ARM: at91: add support for secure suspend on sama5d2
v3 cover ARM: at91: add support for secure suspend on sama5d2
Now that OP-TEE support for sama5d2 is more complete, add support to execute SMC calls and to set suspend mode. This series adds new files to be able to execute SMC calls targeting OP-TEE secure monitor. Then secure suspend support is added and uses these new functions.
---
Changes in v3:
- Move warning for standby in sama5d2_pm_init()
- Remove missleading message in ATMEL_SECURE_PM help
Changes in v2:
- Add suspend mode SMC in already existing secure support
Clément Léger (2):
ARM: at91: add code to handle secure calls
ARM: at91: pm: add support for sama5d2 secure suspend
arch/arm/mach-at91/Kconfig | 11 +++++++- arch/arm/mach-at91/Makefile | 2 +- arch/arm/mach-at91/pm.c | 36 ++++++++++++++++++++++++++ arch/arm/mach-at91/sam_secure.c | 46 +++++++++++++++++++++++++++++++++ arch/arm/mach-at91/sam_secure.h | 18 +++++++++++++ arch/arm/mach-at91/sama5.c | 2 ++ 6 files changed, 113 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-at91/sam_secure.c create mode 100644 arch/arm/mach-at91/sam_secure.h
Signature · 1 line
2.34.1
PATCH v3 1/2 ARM: at91: add code to handle secure calls
Since OP-TEE now has a more complete support for sama5d2, add necessary code to perform SMC calls. The detection of OP-TEE is based on a specific device-tree node path (/firmware/optee) such has done by some other SoC. A check is added to avoid doing SMC calls without having OP-TEE.
--- arch/arm/mach-at91/Makefile | 2 +- arch/arm/mach-at91/sam_secure.c | 46 +++++++++++++++++++++++++++++++++ arch/arm/mach-at91/sam_secure.h | 14 ++++++++++ arch/arm/mach-at91/sama5.c | 2 ++ 4 files changed, 63 insertions(+), 1 deletion(-) create mode 100644 arch/arm/mach-at91/sam_secure.c create mode 100644 arch/arm/mach-at91/sam_secure.h
arch/arm/mach-at91/Makefile +1 -1
@@ -7,7 +7,7 @@ obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o obj-$(CONFIG_SOC_AT91SAM9) += at91sam9.o obj-$(CONFIG_SOC_SAM9X60) += sam9x60.o -obj-$(CONFIG_SOC_SAMA5) += sama5.o +obj-$(CONFIG_SOC_SAMA5) += sama5.o sam_secure.o obj-$(CONFIG_SOC_SAMA7) += sama7.o obj-$(CONFIG_SOC_SAMV7) += samv7.o
arch/arm/mach-at91/sam_secure.c new file +46 -0
46 lines not on this page · raw message
arch/arm/mach-at91/sam_secure.h new file +14 -0
@@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* +* Copyright (C) 2022, Microchip +*/ + +#ifndef SAM_SECURE_H +#define SAM_SECURE_H + +#include <linux/arm-smccc.h> + +void __init sam_secure_init (void ); +struct arm_smccc_res sam_smccc_call (u32 fn,u32 arg0,u32 arg1); + +#endif /* SAM_SECURE_H */
arch/arm/mach-at91/sama5.c +2 -0
@@ -14,6 +14,7 @@#include <asm/system_misc.h> #include "generic.h" +#include "sam_secure.h" static void __init sama5_dt_device_init (void ) {
@@ -47,6 +48,7 @@ MACHINE_ENDstatic void __init sama5d2_init (void ) {of_platform_default_populate (NULL ,NULL ,NULL ); +sam_secure_init ();sama5d2_pm_init (); }
Signature · 1 line
2.34.1
PATCH v3 2/2 ARM: at91: pm: add support for sama5d2 secure suspend
In reply to Clément LégerWhen running with OP-TEE, the suspend control is handled securely. Suspend can be entered using PSCI support. Since the sama5d2 supports multiple suspend modes, add a new CONFIG_ATMEL_SECURE_PM which will send a SMC call to select the suspend mode at init time.
"atmel.pm_modes" boot argument is still supported for compatibility purposes but the standby value is actually ignored since PSCI suspend is used and it only support one mode (suspend).
--- arch/arm/mach-at91/Kconfig | 11 +++++++++- arch/arm/mach-at91/pm.c | 36 +++++++++++++++++++++++++++++++++ arch/arm/mach-at91/sam_secure.h | 4 ++++ 3 files changed, 50 insertions(+), 1 deletion(-)
arch/arm/mach-at91/Kconfig +10 -1
@@ -209,7 +209,16 @@ config SOC_SAMA5 select SRAM if PM config ATMEL_PM - bool + bool "Atmel PM support" + +config ATMEL_SECURE_PM + bool "Atmel Secure PM support" + depends on SOC_SAMA5D2 && ATMEL_PM + select ARM_PSCI + help + When running under a TEE, the suspend mode must be requested to be set + at TEE level. When enable, this option will use secure monitor calls + to set the suspend level. PSCI is then used to enter suspend. config SOC_SAMA7 bool
arch/arm/mach-at91/pm.c +36 -0
@@ -27,6 +27,7 @@#include "generic.h" #include "pm.h" +#include "sam_secure.h" #define BACKUP_DDR_PHY_CALIBRATION (9)
@@ -881,6 +882,35 @@ static int __init at91_pm_backup_init(void)return ret; } +static void at91_pm_secure_init (void ) +{ +int suspend_mode; +struct arm_smccc_res res; + + suspend_mode = soc_pm.data.suspend_mode; + + res =sam_smccc_call (SAMA5_SMC_SIP_SET_SUSPEND_MODE , + suspend_mode,0 ); +if (res.a0 ==0 ) { +pr_info ("AT91: Secure PM: suspend mode set to %s\n" , + pm_modes[suspend_mode].pattern); +return ; + } + +pr_warn ("AT91: Secure PM: %s mode not supported !\n" , + pm_modes[suspend_mode].pattern); + + res =sam_smccc_call (SAMA5_SMC_SIP_GET_SUSPEND_MODE ,0 ,0 ); +if (res.a0 ==0 ) { +pr_warn ("AT91: Secure PM: failed to get default mode\n" ); +return ; + } + +pr_info ("AT91: Secure PM: using default suspend mode %s\n" , + pm_modes[suspend_mode].pattern); + + soc_pm.data.suspend_mode = res.a1; +}static const struct of_device_id atmel_shdwc_ids[] = { { .compatible ="atmel,sama5d2-shdwc" }, { .compatible ="microchip,sam9x60-shdwc" },
@@ -1213,6 +1243,12 @@ void __init sama5d2_pm_init(void)if (!IS_ENABLED (CONFIG_SOC_SAMA5D2 ))return ; +if (IS_ENABLED (CONFIG_ATMEL_SECURE_PM )) { +pr_warn ("AT91: Secure PM: ignoring standby mode\n" ); +at91_pm_secure_init (); +return ; + } +at91_pm_modes_validate (modes,ARRAY_SIZE (modes));at91_pm_modes_init (iomaps,ARRAY_SIZE (iomaps)); ret =at91_dt_ramc (false);
arch/arm/mach-at91/sam_secure.h +4 -0
@@ -8,6 +8,10 @@#include <linux/arm-smccc.h> +/* Secure Monitor mode APIs */ +#define SAMA5_SMC_SIP_SET_SUSPEND_MODE 0x400 +#define SAMA5_SMC_SIP_GET_SUSPEND_MODE 0x401 +void __init sam_secure_init (void );struct arm_smccc_res sam_smccc_call (u32 fn,u32 arg0,u32 arg1);
Signature · 1 line
2.34.1