Skip to contentSkip to conversation

ARM: dts: stm32: Move DHCOR BUCK3 VDD 2V9 adjustment to 1V8 DTSI

PATCH In review Marek Vasut 2 participants 2 messages May 4, 2022 – Jun 13, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: stm32: Move DHCOR BUCK3 VDD 2V9 adjustment to 1V8 DTSI

The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3 in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant which has extra Empirion DCDC converter in front of the 1V8 IO supply, or outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.

The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily high input voltage to the Empirion DCDC converter, so move it into matching DTSI to stop confusing users.

To: [email protected]

---
 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 5 +++++
 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi   | 4 ++--
 2 files changed, 7 insertions(+), 2 deletions(-)
arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi +5 -0
index 75172314d7afd..9937b28548c23 100644
@@ -18,6 +18,11 @@ vdd_io: regulator-buck-io {
 	};
 };
 
+&vdd {
+	regulator-min-microvolt = <2900000>;
+	regulator-max-microvolt = <2900000>;
+};
+
 &pwr_regulators {
 	vdd-supply = <&vdd_io>;
 };
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi +2 -2
index 6336c3ca0f0e2..134a798ad3f23 100644
@@ -119,8 +119,8 @@ vdd_ddr: buck2 {
 
 			vdd: buck3 {
 				regulator-name = "vdd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
 				regulator-over-current-protection;
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#1 lore raw

Hi Marek

Quoted 39 lines · Marek Vasut

The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3 in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant which has extra Empirion DCDC converter in front of the 1V8 IO supply, or outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.

The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily high input voltage to the Empirion DCDC converter, so move it into matching DTSI to stop confusing users.

To: [email protected]

---
  arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 5 +++++
  arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi   | 4 ++--
  2 files changed, 7 insertions(+), 2 deletions(-)
arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi +5 -0
index 75172314d7afd..9937b28548c23 100644
@@ -18,6 +18,11 @@ vdd_io: regulator-buck-io {
  	};
  };
 
+&vdd {
+	regulator-min-microvolt = <2900000>;
+	regulator-max-microvolt = <2900000>;
+};
+
  &pwr_regulators {
  	vdd-supply = <&vdd_io>;
  };
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi +0 -0
index 6336c3ca0f0e2..134a798ad3f23 100644

arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi vdd_ddr: buck2 { · line 126

Quoted 10 lines
arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi +2 -2
@@ -119,8 +119,8 @@ vdd_ddr: buck2 {
 
  			vdd: buck3 {
  				regulator-name = "vdd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
  				regulator-always-on;
  				regulator-initial-mode = <0>;
  				regulator-over-current-protection;

Applied on stm32-next.

Thanks.
Alex

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel