j721e: Add HyperFlash boot support
Subsystems (2)
cover j721e: Add HyperFlash boot support
This series adds support for Hyperflash boot for J721E, the changeset includes the missing pieces from:
https://lore.kernel.org/all/[email protected]/T/#r2f1578fff04474473c82261670b88d2af16841ef
and minor changes to support both OSPI and HyperFlash boot based on the Hypermux selection state similar to as done for J7200.
Changes were tested on J721E SR1.1 for Hyperflash and OSPI boot.
Thanks and Regards,
Vaishnav
Vaishnav Achath (9):
arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
arm: dts: k3-j721e-som-p0: Add HyperFlash node
arm: dts: k3-j721e-r5-common-proc-board: Add HyperFlash node
arm: dts: k3-j721e-common-proc-board-u-boot: enable HyperFlash in SPL
arm: dts: k3-j721e-common-proc-board: enable hyperflash mux sel GPIO
arm: k3: sysfw-loader: add hyperflash support
configs: j721e_evm.h: define CONFIG_SYS_FLASH_BASE
ti: j721e: enable hyperflash spl fixup for j721e
configs: j721e_evm_defconfig: Add HBMC related configs
.../k3-j721e-common-proc-board-u-boot.dtsi | 24 ++++++++ arch/arm/dts/k3-j721e-common-proc-board.dts | 11 ++++ arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 20 ++++++- .../arm/dts/k3-j721e-r5-common-proc-board.dts | 45 +++++++++++++++ arch/arm/dts/k3-j721e-som-p0.dtsi | 32 +++++++++++ arch/arm/mach-k3/sysfw-loader.c | 28 +++++++++ board/ti/j721e/evm.c | 57 ++++++++++++++++++- configs/j721e_evm_a72_defconfig | 5 ++ configs/j721e_evm_r5_defconfig | 14 +++++ include/configs/j721e_evm.h | 2 + 10 files changed, 234 insertions(+), 4 deletions(-)
Signature · 1 line
2.17.1
PATCH 1/9 arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
Add DT node for HyperBus Memory Controller and hbmc-mux in the FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails with current compatible setting.
--- arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 20 +++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)
arch/arm/dts/k3-j721e-mcu-wakeup.dtsi +19 -1
@@ -170,12 +170,30 @@ }; fss: fss@47000000 { - compatible = "simple-bus"; + compatible = "syscon", "simple-mfd"; reg = <0x0 0x47000000 0x0 0x100>; #address-cells = <2>; #size-cells = <2>; ranges; + hbmc_mux: hbmc-mux { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4 0x2>; /* HBMC select */ + }; + + hbmc: hyperbus@47034000 { + compatible = "ti,j721e-hbmc", "ti,am654-hbmc"; + reg = <0x0 0x47034000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <2>; + #size-cells = <1>; + mux-controls = <&hbmc_mux 0>; + assigned-clocks = <&k3_clks 102 0>; + assigned-clock-rates = <250000000>; + }; + ospi0: spi@47040000 { compatible = "ti,am654-ospi", "cdns,qspi-nor"; reg = <0x0 0x47040000 0x0 0x100>,
Signature · 1 line
2.17.1
Re: [PATCH 1/9] arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
Quoted 5 lines · Vaishnav Achath
Add DT node for HyperBus Memory Controller and hbmc-mux in the FSS. hbmc-am654 driver uses
syscon_get_regmap()call which fails with current compatible setting.Signed-off-by Vaishnav Achath <[email protected]>
For the series, applied to u-boot/next, thanks!
Signature · 1 line
Tom
PATCH 2/9 arm: dts: k3-j721e-som-p0: Add HyperFlash node
In reply to Vaishnav AchathJ721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the same.
--- arch/arm/dts/k3-j721e-som-p0.dtsi | 32 +++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/dts/k3-j721e-som-p0.dtsi +32 -0
@@ -150,6 +150,25 @@ >; }; + mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (E20) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */ + J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C21) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */ + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (F19) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */ + J721E_WKUP_IOPAD(0x54, PIN_OUTPUT, 3) /* (E22) MCU_OSPI1_CSn1.MCU_HYPERBUS0_CSn1 */ + J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (E19) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */ + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (D21) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */ + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D20) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */ + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (G19) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */ + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (G20) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */ + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (F20) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */ + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (F21) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */ + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (E21) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */ + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (B22) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */ + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (G21) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ + >; + }; + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { pinctrl-single,pins = < J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -167,6 +186,19 @@ }; }; +&hbmc { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_hpb0_pins_default>; + ranges = <0x0 0x0 0x5 0x0 0x4000000>, /* 64MB Flash on CS0 */ + <0x1 0x0 0x5 0x4000000 0x800000>; /* 8MB RAM on CS1 */ + + flash@0,0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + }; +}; + &ospi0 { pinctrl-names = "default"; pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
Signature · 1 line
2.17.1
PATCH 3/9 arm: dts: k3-j721e-r5-common-proc-board: Add HyperFlash node
In reply to Vaishnav AchathJ721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the same.
--- .../arm/dts/k3-j721e-r5-common-proc-board.dts | 45 +++++++++++++++++++ 1 file changed, 45 insertions(+)
arch/arm/dts/k3-j721e-r5-common-proc-board.dts +45 -0
@@ -129,6 +129,31 @@ >; }; + mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (E20) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */ + J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C21) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */ + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (F19) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */ + J721E_WKUP_IOPAD(0x54, PIN_OUTPUT, 3) /* (E22) MCU_OSPI1_CSn1.MCU_HYPERBUS0_CSn1 */ + J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (E19) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */ + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (D21) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */ + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D20) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */ + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (G19) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */ + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (G20) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */ + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (F20) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */ + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (F21) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */ + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (E21) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */ + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (B22) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */ + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (G21) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ + >; + }; + + wkup_gpio_pins_default: wkup-gpio-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xd0, PIN_INPUT, 7) /* WKUP_GPIO0_8 */ + >; + }; + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { pinctrl-single,pins = < J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -207,6 +232,11 @@ status = "okay"; }; +&wkup_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&wkup_gpio_pins_default>; +}; + &mcu_uart0 { /delete-property/ power-domains; /delete-property/ clocks;
@@ -307,6 +337,21 @@ }; }; +&hbmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_hpb0_pins_default>; + reg = <0x0 0x47040000 0x0 0x100>, + <0x0 0x50000000 0x0 0x8000000>; + ranges = <0x0 0x0 0x0 0x50000000 0x4000000>, /* 64MB Flash on CS0 */ + <0x1 0x0 0x0 0x54000000 0x800000>; /* 8MB flash on CS1 */ + + flash@0,0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + }; +}; + &ospi0 { pinctrl-names = "default"; pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
Signature · 1 line
2.17.1
PATCH 4/9 arm: dts: k3-j721e-common-proc-board-u-boot: enable HyperFlash in SPL
In reply to Vaishnav Achathadd u-boot,dm-spl pre-relocation property to enable hbmc in SPL.
--- .../k3-j721e-common-proc-board-u-boot.dtsi | 24 +++++++++++++++++++ 1 file changed, 24 insertions(+)
arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi +24 -0
@@ -192,6 +192,22 @@ u-boot,dm-spl; }; +&hbmc { + u-boot,dm-spl; + + flash@0,0 { + u-boot,dm-spl; + }; +}; + +&hbmc_mux { + u-boot,dm-spl; +}; + +&wkup_gpio0 { + u-boot,dm-spl; +}; + &ospi0 { u-boot,dm-spl;
@@ -208,6 +224,14 @@ }; }; +&mcu_fss0_hpb0_pins_default { + u-boot,dm-spl; +}; + +&wkup_gpio_pins_default { + u-boot,dm-spl; +}; + &mcu_fss0_ospi1_pins_default { u-boot,dm-spl; };
Signature · 1 line
2.17.1
PATCH 5/9 arm: dts: k3-j721e-common-proc-board: enable hyperflash mux sel GPIO
In reply to Vaishnav AchathAdd wkup_gpio pinmux setting which will be used for performing the DT fixup for hbmc node according to mux selection state, on J721E EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
--- arch/arm/dts/k3-j721e-common-proc-board.dts | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/dts/k3-j721e-common-proc-board.dts +11 -0
@@ -213,6 +213,12 @@ >; }; + wkup_gpio_pins_default: wkup-gpio-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xd0, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_8 */ + >; + }; + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default { pinctrl-single,pins = < J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
@@ -381,6 +387,11 @@ phy-names = "cdns3,usb3-phy"; }; +&wkup_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&wkup_gpio_pins_default>; +}; + &usbss1 { pinctrl-names = "default"; pinctrl-0 = <&main_usbss1_pins_default>;
Signature · 1 line
2.17.1
PATCH 6/9 arm: k3: sysfw-loader: add hyperflash support
In reply to Vaishnav Achathadd support for loading system firmware from hyperflash.
--- arch/arm/mach-k3/sysfw-loader.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
arch/arm/mach-k3/sysfw-loader.c +28 -0
@@ -346,6 +346,25 @@ static void k3_sysfw_spi_copy(u32 *dst, u32 *src, size_t len) }#endif +#if CONFIG_IS_ENABLED (NOR_SUPPORT ) +static void *get_sysfw_hf_addr (void ) +{ +struct udevice *dev; +fdt_addr_t addr; +int ret; + + ret =uclass_find_first_device (UCLASS_MTD , &dev); +if (ret) +return NULL ; + + addr =dev_read_addr_index (dev,1 ); +if (addr ==FDT_ADDR_T_NONE ) +return NULL ; + +return (void *)(addr +CONFIG_K3_SYSFW_IMAGE_SPI_OFFS ); +} +#endif +void k3_sysfw_loader (bool rom_loaded_sysfw,void (*config_pm_pre_callback)(void ),void (*config_pm_done_callback)(void ))
@@ -413,6 +432,15 @@ void k3_sysfw_loader(bool rom_loaded_sysfw, CONFIG_K3_SYSFW_IMAGE_SIZE_MAX);break ;#endif +#if CONFIG_IS_ENABLED (NOR_SUPPORT ) +case BOOT_DEVICE_HYPERFLASH : + sysfw_spi_base =get_sysfw_hf_addr (); +if (!sysfw_spi_base) + ret = -ENODEV ; +k3_sysfw_spi_copy (sysfw_load_address, sysfw_spi_base, +CONFIG_K3_SYSFW_IMAGE_SIZE_MAX ); +break ; +#endif #if CONFIG_IS_ENABLED (YMODEM_SUPPORT )case BOOT_DEVICE_UART :#ifdef CONFIG_K3_EARLY_CONS
Signature · 1 line
2.17.1
PATCH 7/9 configs: j721e_evm.h: define CONFIG_SYS_FLASH_BASE
In reply to Vaishnav AchathDefine CONFIG_SYS_FLASH_BASE to indicate start address of Flash memory
--- include/configs/j721e_evm.h | 2 ++ 1 file changed, 2 insertions(+)
include/configs/j721e_evm.h +2 -0
@@ -17,6 +17,8 @@/* DDR Configuration */ #define CONFIG_SYS_SDRAM_BASE1 0x880000000 +/* FLASH Configuration */ +#define CONFIG_SYS_FLASH_BASE 0x000000000/* SPL Loader Configuration */ #if defined(CONFIG_TARGET_J721E_A72_EVM ) || defined(CONFIG_TARGET_J7200_A72_EVM )
Signature · 1 line
2.17.1
PATCH 8/9 ti: j721e: enable hyperflash spl fixup for j721e
In reply to Vaishnav AchathOn j721e, its not possible to use OSPI0 and HBMC simultaneously as they are muxed within the Flash Subsystem hence disable HBMC by default and keep OSPI enabled. Bootloader will fixup DT when it detects HyperFlash mux selection instead of OSPI.
Also updated detect_enable_hyperflash to use correct GPIO when checking hypermux selection state:
* J7200 - hypermux sel connected to WKUP_GPIO0_6
* J721E - hypermux·sel·connected·to·WKUP_GPIO0_8
--- board/ti/j721e/evm.c | 57 +++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 54 insertions(+), 3 deletions(-)
board/ti/j721e/evm.c +54 -3
@@ -109,11 +109,12 @@ int board_fit_config_name_match(const char *name)static void __maybe_unused detect_enable_hyperflash (void *blob) {struct gpio_desc desc = {0 }; +char *hypermux_sel_gpio = (board_is_j721e_som ()) ?"8" :"6" ; -if (dm_gpio_lookup_name ("6" , &desc)) +if (dm_gpio_lookup_name (hypermux_sel_gpio, &desc))return ; -if (dm_gpio_request (&desc,"6" )) +if (dm_gpio_request (&desc, hypermux_sel_gpio))return ;if (dm_gpio_set_dir_flags (&desc,GPIOD_IS_IN ))
@@ -132,7 +133,8 @@ static void __maybe_unused detect_enable_hyperflash(void *blob) }#endif -#if defined(CONFIG_SPL_BUILD ) && defined(CONFIG_TARGET_J7200_A72_EVM ) +#if defined(CONFIG_SPL_BUILD ) && (defined(CONFIG_TARGET_J7200_A72_EVM ) || defined(CONFIG_TARGET_J7200_R5_EVM ) || \ + defined(CONFIG_TARGET_J721E_A72_EVM ) || defined(CONFIG_TARGET_J721E_R5_EVM ))void spl_perform_fixups (struct spl_image_info *spl_image) {detect_enable_hyperflash (spl_image->fdt_addr);
@@ -490,6 +492,41 @@ int board_late_init(void) }#endif +static int __maybe_unused detect_SW3_1_state (void ) +{ +if (IS_ENABLED (CONFIG_TARGET_J7200_A72_EVM ) ||IS_ENABLED (CONFIG_TARGET_J721E_A72_EVM )) { +struct gpio_desc desc = {0 }; +int ret; +char *hypermux_sel_gpio = (board_is_j721e_som ()) ?"8" :"6" ; + + ret =dm_gpio_lookup_name (hypermux_sel_gpio, &desc); +if (ret) { +printf ("error getting GPIO lookup name: %d\n" , ret); +return ret; + } + + ret =dm_gpio_request (&desc, hypermux_sel_gpio); +if (ret) { +printf ("error requesting GPIO: %d\n" , ret); + goto err_free_gpio; + } + + ret =dm_gpio_set_dir_flags (&desc,GPIOD_IS_IN ); +if (ret) { +printf ("error setting direction flag of GPIO: %d\n" , ret); + goto err_free_gpio; + } + + ret =dm_gpio_get_value (&desc); +if (ret <0 ) +printf ("error getting value of GPIO: %d\n" , ret); + +err_free_gpio: +dm_gpio_free (desc.dev, &desc); +return ret; + } +} +void spl_board_init (void ) {#if defined(CONFIG_ESM_K3 ) || defined(CONFIG_ESM_PMIC )
@@ -522,4 +559,18 @@ void spl_board_init(void) printf("ESM PMIC init failed: %d\n", ret); }#endif +if ((IS_ENABLED (CONFIG_TARGET_J7200_A72_EVM ) ||IS_ENABLED (CONFIG_TARGET_J721E_A72_EVM )) && +IS_ENABLED (CONFIG_HBMC_AM654 )) { +struct udevice *dev; +int ret; + + ret =detect_SW3_1_state (); +if (ret ==1 ) { + ret =uclass_get_device_by_driver (UCLASS_MTD , +DM_DRIVER_GET (hbmc_am654), + &dev); +if (ret) +debug ("Failed to probe hyperflash\n" ); + } + } }
Signature · 1 line
2.17.1
PATCH 9/9 configs: j721e_evm_defconfig: Add HBMC related configs
In reply to Vaishnav AchathEnable HBMC and HyperFlash in R5SPL, A72 SPL and A72 U-Boot
--- configs/j721e_evm_a72_defconfig | 5 +++++ configs/j721e_evm_r5_defconfig | 14 ++++++++++++++ 2 files changed, 19 insertions(+)
configs/j721e_evm_a72_defconfig +5 -0
@@ -127,6 +127,9 @@ CONFIG_MMC_SDHCI_AM654=y CONFIG_MTD=y CONFIG_DM_MTD=y CONFIG_MTD_NOR_FLASH=y +CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_NOR_SUPPORT=y +CONFIG_FLASH_CFI_DRIVER=y CONFIG_CFI_FLASH=y CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y
@@ -176,6 +179,7 @@ CONFIG_HAS_CQSPI_REF_CLK=y CONFIG_CQSPI_REF_CLK=133333333 CONFIG_SYSRESET=y CONFIG_SPL_SYSRESET=y +CONFIG_SPL_SYSCON=y CONFIG_SYSRESET_TI_SCI=y CONFIG_USB=y CONFIG_DM_USB_GADGET=y
@@ -193,3 +197,4 @@ CONFIG_UFS=y CONFIG_CADENCE_UFS=y CONFIG_TI_J721E_UFS=y CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_OF_BOARD_SETUP=y
configs/j721e_evm_r5_defconfig +14 -0
@@ -21,6 +21,9 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_NOR_SUPPORT=y +CONFIG_OF_BOARD_SETUP=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
@@ -101,6 +104,17 @@ CONFIG_MMC_SDHCI=y CONFIG_SPL_MMC_SDHCI_ADMA=y CONFIG_MMC_SDHCI_AM654=y CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_HBMC_AM654=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +CONFIG_FLASH_CFI_DRIVER=y +CONFIG_CFI_FLASH=y +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_SYS_FLASH_CFI=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_SFDP_SUPPORT=y CONFIG_SPI_FLASH_STMICRO=y
Signature · 1 line
2.17.1