Skip to contentSkip to conversation

floppy: use a statically allocated error counter

PATCH In review Willy Tarreau 4 participants 11 messages May 8, 2022 – May 19, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 floppy: use a statically allocated error counter

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

---
 drivers/block/floppy.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)
drivers/block/floppy.c +8 -10
index d5b9ff9bcbb2..015841f50f4e 100644
@@ -509,8 +509,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -530,7 +530,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1455,7 +1454,7 @@ static int interpret_errors(void)
 			if (drive_params[current_drive].flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= drive_params[current_drive].max_errors.reporting) {
+		} else if (floppy_errors >= drive_params[current_drive].max_errors.reporting) {
 			print_errors();
 		}
 		if (reply_buffer[ST2] & ST2_WC || reply_buffer[ST2] & ST2_BC)
@@ -2095,7 +2094,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format(current_drive))
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(write_errors[current_drive].badness, err_count);
 	if (err_count > drive_params[current_drive].max_errors.abort)
 		cont->done(0);
@@ -2241,9 +2240,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2759,10 +2757,11 @@ static int set_next_request(void)
 	current_req = list_first_entry_or_null(&floppy_reqs, struct request,
 					       queuelist);
 	if (current_req) {
-		current_req->error_count = 0;
+		floppy_errors = 0;
 		list_del_init(&current_req->queuelist);
+		return 1;
 	}
-	return current_req != NULL;
+	return 0;
 }
 
 /* Starts or continues processing request. Will automatically unlock the
@@ -2821,7 +2820,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + drive_params[current_drive].autodetect[drive_state[current_drive].probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
Signature · 1 line
2.17.5
#1 lore raw

PATCH 2/3 ataflop: use a statically allocated error counters

This is the last driver making use of fd_request->error_count, which is easy to get wrong as was shown in floppy.c. We don't need to keep it there, it can be moved to the atari_floppy_struct instead, so let's do this.

---
 drivers/block/ataflop.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/block/ataflop.c +6 -4
index 5d819a466e2f..e232cc4fd444 100644
@@ -303,6 +303,7 @@ static struct atari_floppy_struct {
 	int ref;
 	int type;
 	struct blk_mq_tag_set tag_set;
+	int error_count;
 } unit[FD_MAX_UNITS];
 
 #define	UD	unit[drive]
@@ -705,14 +706,14 @@ static void fd_error( void )
 	if (!fd_request)
 		return;
 
-	fd_request->error_count++;
-	if (fd_request->error_count >= MAX_ERRORS) {
+	unit[SelectedDrive].error_count++;
+	if (unit[SelectedDrive].error_count >= MAX_ERRORS) {
 		printk(KERN_ERR "fd%d: too many errors.\n", SelectedDrive );
 		fd_end_request_cur(BLK_STS_IOERR);
 		finish_fdc();
 		return;
 	}
-	else if (fd_request->error_count == RECALIBRATE_ERRORS) {
+	else if (unit[SelectedDrive].error_count == RECALIBRATE_ERRORS) {
 		printk(KERN_WARNING "fd%d: recalibrating\n", SelectedDrive );
 		if (SelectedDrive != -1)
 			SUD.track = -1;
@@ -1491,7 +1492,7 @@ static void setup_req_params( int drive )
 	ReqData = ReqBuffer + 512 * ReqCnt;
 
 	if (UseTrackbuffer)
-		read_track = (ReqCmd == READ && fd_request->error_count == 0);
+		read_track = (ReqCmd == READ && unit[drive].error_count == 0);
 	else
 		read_track = 0;
 
@@ -1520,6 +1521,7 @@ static blk_status_t ataflop_queue_rq(struct blk_mq_hw_ctx *hctx,
 		return BLK_STS_RESOURCE;
 	}
 	fd_request = bd->rq;
+	unit[drive].error_count = 0;
 	blk_mq_start_request(fd_request);
 
 	atari_disable_irq( IRQ_MFP_FDC );
Signature · 1 line
2.17.5
#2 lore raw

PATCH 3/3 blk-mq: remove the error_count from struct request

In reply to Willy Tarreau

The last two users were floppy.c and ataflop.c respectively, it was verified that no other drivers makes use of this, so let's remove it.

Cc Minh Yuan <[email protected]>
Cc Denis Efremov <[email protected]>,
Cc Geert Uytterhoeven <[email protected]>
Cc Christoph Hellwig <[email protected]>
---
 include/linux/blk-mq.h | 1 -
 1 file changed, 1 deletion(-)
include/linux/blk-mq.h +0 -1
index 7aa5c54901a9..9f07061418db 100644
@@ -163,7 +163,6 @@ struct request {
 		struct rb_node rb_node;	/* sort/lookup */
 		struct bio_vec special_vec;
 		void *completion_data;
-		int error_count; /* for legacy drivers, don't use */
 	};
 
 
Signature · 1 line
2.17.5
maintainer
#5 lore raw
In reply to Willy Tarreau

Hi,

Quoted 15 lines · Willy Tarreau

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

Quoted 4 lines

Could you please take this patch (only this one) to the stable trees?

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

The patch applies cleanly to 5.17, 5.15, 5.10 kernels. I'll send a backport for 5.4 and older kernels.

Thanks,
Denis

Quoted 78 lines
---
 drivers/block/floppy.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)
drivers/block/floppy.c +8 -10
index d5b9ff9bcbb2..015841f50f4e 100644
@@ -509,8 +509,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -530,7 +530,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1455,7 +1454,7 @@ static int interpret_errors(void)
 			if (drive_params[current_drive].flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= drive_params[current_drive].max_errors.reporting) {
+		} else if (floppy_errors >= drive_params[current_drive].max_errors.reporting) {
 			print_errors();
 		}
 		if (reply_buffer[ST2] & ST2_WC || reply_buffer[ST2] & ST2_BC)
@@ -2095,7 +2094,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format(current_drive))
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(write_errors[current_drive].badness, err_count);
 	if (err_count > drive_params[current_drive].max_errors.abort)
 		cont->done(0);
@@ -2241,9 +2240,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2759,10 +2757,11 @@ static int set_next_request(void)
 	current_req = list_first_entry_or_null(&floppy_reqs, struct request,
 					       queuelist);
 	if (current_req) {
-		current_req->error_count = 0;
+		floppy_errors = 0;
 		list_del_init(&current_req->queuelist);
+		return 1;
 	}
-	return current_req != NULL;
+	return 0;
 }
 
 /* Starts or continues processing request. Will automatically unlock the
@@ -2821,7 +2820,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + drive_params[current_drive].autodetect[drive_state[current_drive].probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
#6 lore raw
Quoted 23 lines · Denis Efremov

Hi,

Quoted 15 lines · Willy Tarreau

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

Quoted 4 lines
Quoted 6 lines

Could you please take this patch (only this one) to the stable trees?

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

The patch applies cleanly to 5.17, 5.15, 5.10 kernels. I'll send a backport for 5.4 and older kernels.

All now queued up, thanks.

greg k-h

maintainer
#7 lore raw

PATCH 1/1 floppy: use a statically allocated error counter

In reply to Willy Tarreau

From: Willy Tarreau <[email protected]>

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

---

Handled *errors in make_raw_rw_request().

 drivers/block/floppy.c | 20 +++++++++-----------
 1 file changed, 9 insertions(+), 11 deletions(-)
drivers/block/floppy.c +9 -11
index c9411fe2f0af..4ef407a33996 100644
@@ -509,8 +509,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -530,7 +530,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1455,7 +1454,7 @@ static int interpret_errors(void)
 			if (drive_params[current_drive].flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= drive_params[current_drive].max_errors.reporting) {
+		} else if (floppy_errors >= drive_params[current_drive].max_errors.reporting) {
 			print_errors();
 		}
 		if (reply_buffer[ST2] & ST2_WC || reply_buffer[ST2] & ST2_BC)
@@ -2095,7 +2094,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format(current_drive))
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(write_errors[current_drive].badness, err_count);
 	if (err_count > drive_params[current_drive].max_errors.abort)
 		cont->done(0);
@@ -2240,9 +2239,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2721,7 +2719,7 @@ static int make_raw_rw_request(void)
 		 */
 		if (!direct ||
 		    (indirect * 2 > direct * 3 &&
-		     *errors < drive_params[current_drive].max_errors.read_track &&
+		     floppy_errors < drive_params[current_drive].max_errors.read_track &&
 		     ((!probing ||
 		       (drive_params[current_drive].read_track & (1 << drive_state[current_drive].probed_format)))))) {
 			max_size = blk_rq_sectors(current_req);
@@ -2846,10 +2844,11 @@ static int set_next_request(void)
 	current_req = list_first_entry_or_null(&floppy_reqs, struct request,
 					       queuelist);
 	if (current_req) {
-		current_req->error_count = 0;
+		floppy_errors = 0;
 		list_del_init(&current_req->queuelist);
+		return 1;
 	}
-	return current_req != NULL;
+	return 0;
 }
 
 /* Starts or continues processing request. Will automatically unlock the
@@ -2908,7 +2907,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + drive_params[current_drive].autodetect[drive_state[current_drive].probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
Signature · 1 line
2.35.3
maintainer
#8 lore raw

PATCH 1/1 floppy: use a statically allocated error counter

In reply to Willy Tarreau

From: Willy Tarreau <[email protected]>

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

---
 drivers/block/floppy.c | 20 +++++++++-----------
 1 file changed, 9 insertions(+), 11 deletions(-)
drivers/block/floppy.c +9 -11
index f24e3791e840..e133ff5fa596 100644
@@ -521,8 +521,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -542,7 +542,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1435,7 +1434,7 @@ static int interpret_errors(void)
 			if (DP->flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= DP->max_errors.reporting) {
+		} else if (floppy_errors >= DP->max_errors.reporting) {
 			print_errors();
 		}
 		if (ST2 & ST2_WC || ST2 & ST2_BC)
@@ -2055,7 +2054,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format())
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(DRWE->badness, err_count);
 	if (err_count > DP->max_errors.abort)
 		cont->done(0);
@@ -2200,9 +2199,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2677,7 +2675,7 @@ static int make_raw_rw_request(void)
 		 */
 		if (!direct ||
 		    (indirect * 2 > direct * 3 &&
-		     *errors < DP->max_errors.read_track &&
+		     floppy_errors < DP->max_errors.read_track &&
 		     ((!probing ||
 		       (DP->read_track & (1 << DRS->probed_format)))))) {
 			max_size = blk_rq_sectors(current_req);
@@ -2801,10 +2799,11 @@ static int set_next_request(void)
 	current_req = list_first_entry_or_null(&floppy_reqs, struct request,
 					       queuelist);
 	if (current_req) {
-		current_req->error_count = 0;
+		floppy_errors = 0;
 		list_del_init(&current_req->queuelist);
+		return 1;
 	}
-	return current_req != NULL;
+	return 0;
 }
 
 static void redo_fd_request(void)
@@ -2860,7 +2859,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + DP->autodetect[DRS->probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
Signature · 1 line
2.35.3
maintainer
#9 lore raw

PATCH 1/1 floppy: use a statically allocated error counter

In reply to Willy Tarreau

From: Willy Tarreau <[email protected]>

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

---
 drivers/block/floppy.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)
drivers/block/floppy.c +7 -10
index 97c8fc4d6e7b..0e66314415c5 100644
@@ -520,8 +520,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -541,7 +541,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1434,7 +1433,7 @@ static int interpret_errors(void)
 			if (DP->flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= DP->max_errors.reporting) {
+		} else if (floppy_errors >= DP->max_errors.reporting) {
 			print_errors();
 		}
 		if (ST2 & ST2_WC || ST2 & ST2_BC)
@@ -2054,7 +2053,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format())
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(DRWE->badness, err_count);
 	if (err_count > DP->max_errors.abort)
 		cont->done(0);
@@ -2199,9 +2198,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2684,7 +2682,7 @@ static int make_raw_rw_request(void)
 		 */
 		if (!direct ||
 		    (indirect * 2 > direct * 3 &&
-		     *errors < DP->max_errors.read_track &&
+		     floppy_errors < DP->max_errors.read_track &&
 		     ((!probing ||
 		       (DP->read_track & (1 << DRS->probed_format)))))) {
 			max_size = blk_rq_sectors(current_req);
@@ -2818,7 +2816,7 @@ static int set_next_request(void)
 		if (q) {
 			current_req = blk_fetch_request(q);
 			if (current_req) {
-				current_req->error_count = 0;
+				floppy_errors = 0;
 				break;
 			}
 		}
@@ -2880,7 +2878,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + DP->autodetect[DRS->probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->error_count);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
Signature · 1 line
2.35.3
maintainer
#10 lore raw

PATCH 1/1 floppy: use a statically allocated error counter

In reply to Willy Tarreau

From: Willy Tarreau <[email protected]>

commit f71f01394f742fc4558b3f9f4c7ef4c4cf3b07c8 upstream.

Interrupt handler bad_flp_intr() may cause a UAF on the recently freed request just to increment the error count. There's no point keeping that one in the request anyway, and since the interrupt handler uses a static pointer to the error which cannot be kept in sync with the pending request, better make it use a static error counter that's reset for each new request. This reset now happens when entering redo_fd_request() for a new request via set_next_request().

One initial concern about a single error counter was that errors on one floppy drive could be reported on another one, but this problem is not real given that the driver uses a single drive at a time, as that PC-compatible controllers also have this limitation by using shared signals. As such the error count is always for the "current" drive.

---
 drivers/block/floppy.c | 19 +++++++++----------
 1 file changed, 9 insertions(+), 10 deletions(-)
drivers/block/floppy.c +9 -10
index cfe1bfb3c20e..216ee1057b12 100644
@@ -516,8 +516,8 @@ static unsigned long fdc_busy;
 static DECLARE_WAIT_QUEUE_HEAD(fdc_wait);
 static DECLARE_WAIT_QUEUE_HEAD(command_done);
 
-/* Errors during formatting are counted here. */
-static int format_errors;
+/* errors encountered on the current (or last) request */
+static int floppy_errors;
 
 /* Format request descriptor. */
 static struct format_descr format_req;
@@ -537,7 +537,6 @@ static struct format_descr format_req;
 static char *floppy_track_buffer;
 static int max_buffer_sectors;
 
-static int *errors;
 typedef void (*done_f)(int);
 static const struct cont_t {
 	void (*interrupt)(void);
@@ -1426,7 +1425,7 @@ static int interpret_errors(void)
 			if (DP->flags & FTD_MSG)
 				DPRINT("Over/Underrun - retrying\n");
 			bad = 0;
-		} else if (*errors >= DP->max_errors.reporting) {
+		} else if (floppy_errors >= DP->max_errors.reporting) {
 			print_errors();
 		}
 		if (ST2 & ST2_WC || ST2 & ST2_BC)
@@ -2049,7 +2048,7 @@ static void bad_flp_intr(void)
 		if (!next_valid_format())
 			return;
 	}
-	err_count = ++(*errors);
+	err_count = ++floppy_errors;
 	INFBOUND(DRWE->badness, err_count);
 	if (err_count > DP->max_errors.abort)
 		cont->done(0);
@@ -2194,9 +2193,8 @@ static int do_format(int drive, struct format_descr *tmp_format_req)
 		return -EINVAL;
 	}
 	format_req = *tmp_format_req;
-	format_errors = 0;
 	cont = &format_cont;
-	errors = &format_errors;
+	floppy_errors = 0;
 	ret = wait_til_done(redo_format, true);
 	if (ret == -EINTR)
 		return -EINTR;
@@ -2679,7 +2677,7 @@ static int make_raw_rw_request(void)
 		 */
 		if (!direct ||
 		    (indirect * 2 > direct * 3 &&
-		     *errors < DP->max_errors.read_track &&
+		     floppy_errors < DP->max_errors.read_track &&
 		     ((!probing ||
 		       (DP->read_track & (1 << DRS->probed_format)))))) {
 			max_size = blk_rq_sectors(current_req);
@@ -2812,8 +2810,10 @@ static int set_next_request(void)
 			fdc_queue = 0;
 		if (q) {
 			current_req = blk_fetch_request(q);
-			if (current_req)
+			if (current_req) {
+				floppy_errors = 0;
 				break;
+			}
 		}
 	} while (fdc_queue != old_pos);
 
@@ -2873,7 +2873,6 @@ static void redo_fd_request(void)
 		_floppy = floppy_type + DP->autodetect[DRS->probed_format];
 	} else
 		probing = 0;
-	errors = &(current_req->errors);
 	tmp = make_raw_rw_request();
 	if (tmp < 2) {
 		request_done(tmp);
Signature · 1 line
2.35.3