Skip to contentSkip to conversation

Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"

PATCH In review Jarkko Nikula 2 participants 3 messages May 12, 2022 – May 13, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"

This reverts commit 0e8ffdf3b86dfd44b651f91b12fcae76c25c453b.

Commit 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for Elkhart Lake") broke the test case using bitrate switching.

ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
candump can0 &
cangen can1 -I 0x800 -L 64 -e -fb -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v

Above commit does everything correctly according to the datasheet. However datasheet wasn't correct.

I got confirmation from hardware engineers that the actual CAN hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0. Datasheet was mirroring values from an another specification which was based on earlier M_CAN version leading to wrong bit timings.

Therefore revert the commit and switch back to common bit timings.

Fixes 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for Elkhart Lake")
Cc <[email protected]> # v5.16+
---
 drivers/net/can/m_can/m_can_pci.c | 48 +++----------------------------
 1 file changed, 4 insertions(+), 44 deletions(-)
drivers/net/can/m_can/m_can_pci.c +4 -44
index b56a54d6c5a9..8f184a852a0a 100644
@@ -18,14 +18,9 @@
 
 #define M_CAN_PCI_MMIO_BAR		0
 
+#define M_CAN_CLOCK_FREQ_EHL		200000000
 #define CTL_CSR_INT_CTL_OFFSET		0x508
 
-struct m_can_pci_config {
-	const struct can_bittiming_const *bit_timing;
-	const struct can_bittiming_const *data_timing;
-	unsigned int clock_freq;
-};
-
 struct m_can_pci_priv {
 	struct m_can_classdev cdev;
 
@@ -89,40 +84,9 @@ static struct m_can_ops m_can_pci_ops = {
 	.read_fifo = iomap_read_fifo,
 };
 
-static const struct can_bittiming_const m_can_bittiming_const_ehl = {
-	.name = KBUILD_MODNAME,
-	.tseg1_min = 2,		/* Time segment 1 = prop_seg + phase_seg1 */
-	.tseg1_max = 64,
-	.tseg2_min = 1,		/* Time segment 2 = phase_seg2 */
-	.tseg2_max = 128,
-	.sjw_max = 128,
-	.brp_min = 1,
-	.brp_max = 512,
-	.brp_inc = 1,
-};
-
-static const struct can_bittiming_const m_can_data_bittiming_const_ehl = {
-	.name = KBUILD_MODNAME,
-	.tseg1_min = 2,		/* Time segment 1 = prop_seg + phase_seg1 */
-	.tseg1_max = 16,
-	.tseg2_min = 1,		/* Time segment 2 = phase_seg2 */
-	.tseg2_max = 8,
-	.sjw_max = 4,
-	.brp_min = 1,
-	.brp_max = 32,
-	.brp_inc = 1,
-};
-
-static const struct m_can_pci_config m_can_pci_ehl = {
-	.bit_timing = &m_can_bittiming_const_ehl,
-	.data_timing = &m_can_data_bittiming_const_ehl,
-	.clock_freq = 200000000,
-};
-
 static int m_can_pci_probe(struct pci_dev *pci, const struct pci_device_id *id)
 {
 	struct device *dev = &pci->dev;
-	const struct m_can_pci_config *cfg;
 	struct m_can_classdev *mcan_class;
 	struct m_can_pci_priv *priv;
 	void __iomem *base;
@@ -150,8 +114,6 @@ static int m_can_pci_probe(struct pci_dev *pci, const struct pci_device_id *id)
 	if (!mcan_class)
 		return -ENOMEM;
 
-	cfg = (const struct m_can_pci_config *)id->driver_data;
-
 	priv = cdev_to_priv(mcan_class);
 
 	priv->base = base;
@@ -163,9 +125,7 @@ static int m_can_pci_probe(struct pci_dev *pci, const struct pci_device_id *id)
 	mcan_class->dev = &pci->dev;
 	mcan_class->net->irq = pci_irq_vector(pci, 0);
 	mcan_class->pm_clock_support = 1;
-	mcan_class->bit_timing = cfg->bit_timing;
-	mcan_class->data_timing = cfg->data_timing;
-	mcan_class->can.clock.freq = cfg->clock_freq;
+	mcan_class->can.clock.freq = id->driver_data;
 	mcan_class->ops = &m_can_pci_ops;
 
 	pci_set_drvdata(pci, mcan_class);
@@ -218,8 +178,8 @@ static SIMPLE_DEV_PM_OPS(m_can_pci_pm_ops,
 			 m_can_pci_suspend, m_can_pci_resume);
 
 static const struct pci_device_id m_can_pci_id_table[] = {
-	{ PCI_VDEVICE(INTEL, 0x4bc1), (kernel_ulong_t)&m_can_pci_ehl, },
-	{ PCI_VDEVICE(INTEL, 0x4bc2), (kernel_ulong_t)&m_can_pci_ehl, },
+	{ PCI_VDEVICE(INTEL, 0x4bc1), M_CAN_CLOCK_FREQ_EHL, },
+	{ PCI_VDEVICE(INTEL, 0x4bc2), M_CAN_CLOCK_FREQ_EHL, },
 	{  }	/* Terminating Entry */
 };
 MODULE_DEVICE_TABLE(pci, m_can_pci_id_table);
Signature · 1 line
2.35.1
#1 lore raw

PATCH 2/2 can: m_can: remove support for custom bit timing, take #2

Now when Intel Elkhart Lake uses again common bit timing and there are no other users for custom bit timing, we can bring back the changes done by the commit 0ddd83fbebbc ("can: m_can: remove support for custom bit timing").

This effectively reverts commit ea768b2ffec6 ("Revert "can: m_can: remove support for custom bit timing"") while taking into account commit ea22ba40debe ("can: m_can: make custom bittiming fields const") and
commit 7d4a101c0bd3 ("can: dev: add sanity check in can_set_static_ctrlmode()").

---
 drivers/net/can/m_can/m_can.c | 24 ++++++------------------
 drivers/net/can/m_can/m_can.h |  3 ---
 2 files changed, 6 insertions(+), 21 deletions(-)
drivers/net/can/m_can/m_can.c +6 -18
index e6d2da4a9f41..7582908e1192 100644
@@ -1492,34 +1492,22 @@ static int m_can_dev_setup(struct m_can_classdev *cdev)
 		err = can_set_static_ctrlmode(dev, CAN_CTRLMODE_FD_NON_ISO);
 		if (err)
 			return err;
-		cdev->can.bittiming_const = cdev->bit_timing ?
-			cdev->bit_timing : &m_can_bittiming_const_30X;
-
-		cdev->can.data_bittiming_const = cdev->data_timing ?
-			cdev->data_timing :
-			&m_can_data_bittiming_const_30X;
+		cdev->can.bittiming_const = &m_can_bittiming_const_30X;
+		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_30X;
 		break;
 	case 31:
 		/* CAN_CTRLMODE_FD_NON_ISO is fixed with M_CAN IP v3.1.x */
 		err = can_set_static_ctrlmode(dev, CAN_CTRLMODE_FD_NON_ISO);
 		if (err)
 			return err;
-		cdev->can.bittiming_const = cdev->bit_timing ?
-			cdev->bit_timing : &m_can_bittiming_const_31X;
-
-		cdev->can.data_bittiming_const = cdev->data_timing ?
-			cdev->data_timing :
-			&m_can_data_bittiming_const_31X;
+		cdev->can.bittiming_const = &m_can_bittiming_const_31X;
+		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_31X;
 		break;
 	case 32:
 	case 33:
 		/* Support both MCAN version v3.2.x and v3.3.0 */
-		cdev->can.bittiming_const = cdev->bit_timing ?
-			cdev->bit_timing : &m_can_bittiming_const_31X;
-
-		cdev->can.data_bittiming_const = cdev->data_timing ?
-			cdev->data_timing :
-			&m_can_data_bittiming_const_31X;
+		cdev->can.bittiming_const = &m_can_bittiming_const_31X;
+		cdev->can.data_bittiming_const = &m_can_data_bittiming_const_31X;
 
 		cdev->can.ctrlmode_supported |=
 			(m_can_niso_supported(cdev) ?
drivers/net/can/m_can/m_can.h +0 -3
index 2c5d40997168..d18b515e6ccc 100644
@@ -85,9 +85,6 @@ struct m_can_classdev {
 	struct sk_buff *tx_skb;
 	struct phy *transceiver;
 
-	const struct can_bittiming_const *bit_timing;
-	const struct can_bittiming_const *data_timing;
-
 	struct m_can_ops *ops;
 
 	int version;
Signature · 1 line
2.35.1
#2 lore raw
In reply to Jarkko Nikula
Quoted 18 lines · Jarkko Nikula

This reverts commit 0e8ffdf3b86dfd44b651f91b12fcae76c25c453b.

Commit 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for Elkhart Lake") broke the test case using bitrate switching.

ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
candump can0 &
cangen can1 -I 0x800 -L 64 -e -fb -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v

Above commit does everything correctly according to the datasheet. However datasheet wasn't correct.

I got confirmation from hardware engineers that the actual CAN hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0. Datasheet was mirroring values from an another specification which was based on earlier M_CAN version leading to wrong bit timings.

Quoted 8 lines

Therefore revert the commit and switch back to common bit timings.

Fixes 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for Elkhart Lake")
Cc <[email protected]> # v5.16+

Added to can/testing.

Thanks,
Marc

Signature · 4 lines
Pengutronix e.K.                 | Marc Kleine-Budde           |
Embedded Linux                   | https://www.pengutronix.de  |
Vertretung West/Dortmund         | Phone: +49-231-2826-924     |
Amtsgericht Hildesheim, HRA 2686 | Fax:   +49-5121-206917-5555 |