Skip to contentSkip to conversation

Enable QSPI and SF command

PATCH In review Sergiu Moga 2 participants 5 messages May 13, 2022 – Jun 7, 2022 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

cover Enable QSPI and SF command

This patch series enables the SF command and QSPI for the MMC and NANDFLASH defconfigs in the case of the sam9x60 board and for the MMC defconfig in the case of the sama5d2_icp board. It also changes the compatible of the qspi child node from the board file of sam9x60 so that it can be properly found when probing the bus.

Sergiu Moga (3):
ARM: dts: sam9x60: fix compatible for qspi child node
configs: at91: sam9x60ek: enable QSPI and SF command
configs: at91: sama5d2_icp: enable QSPI and SF command

 arch/arm/dts/sam9x60ek.dts            |  2 +-
 configs/sam9x60ek_mmc_defconfig       | 13 +++++++++++++
 configs/sam9x60ek_nandflash_defconfig | 13 +++++++++++++
 configs/sama5d2_icp_mmc_defconfig     | 13 +++++++++++++
 4 files changed, 40 insertions(+), 1 deletion(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/3 ARM: dts: sam9x60: fix compatible for qspi child node

Change the compatible of the qspi child node to
jedec,spi-nor so that it can be properly found
when probing the bus.

---
 arch/arm/dts/sam9x60ek.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/sam9x60ek.dts +1 -1
index 32ffe93b4d..4258e8e1ab 100644
@@ -49,7 +49,7 @@
 				status = "okay";
 
 				nor_flash: sst26vf064@0 {
-					compatible = "spi-flash";
+					compatible = "jedec,spi-nor";
 					reg = <0>;
 					spi-max-frequency = <80000000>;
 					spi-rx-bus-width = <4>;
Signature · 1 line
2.25.1
#2 lore raw

PATCH 2/3 configs: at91: sam9x60ek: enable QSPI and SF command

In reply to Sergiu Moga

Add the configurations required for enabling QSPI and the SF command to allow changes to be made dynamically to serial flash devices from the command line interface.

---
 configs/sam9x60ek_mmc_defconfig       | 13 +++++++++++++
 configs/sam9x60ek_nandflash_defconfig | 13 +++++++++++++
 2 files changed, 26 insertions(+)
configs/sam9x60ek_mmc_defconfig +13 -0
index bc0164c38e..cab469877a 100644
@@ -33,6 +33,7 @@ CONFIG_CMD_DM=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_NAND=y
 CONFIG_CMD_NAND_TRIMFFS=y
 # CONFIG_CMD_SETEXPR is not set
@@ -63,6 +64,8 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
 CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
+CONFIG_SF_DEFAULT_MODE=0x0
+CONFIG_SF_DEFAULT_SPEED=50000000
 CONFIG_NAND_ATMEL=y
 CONFIG_ATMEL_NAND_HW_PMECC=y
 CONFIG_PMECC_CAP=8
@@ -84,3 +87,13 @@ CONFIG_W1_GPIO=y
 CONFIG_W1_EEPROM=y
 CONFIG_W1_EEPROM_DS24XXX=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_ATMEL_QSPI=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_MTD=y
configs/sam9x60ek_nandflash_defconfig +13 -0
index 5c34f089e6..7c1a473208 100644
@@ -33,6 +33,7 @@ CONFIG_CMD_DM=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_NAND=y
 CONFIG_CMD_NAND_TRIMFFS=y
@@ -69,6 +70,15 @@ CONFIG_ATMEL_NAND_HW_PMECC=y
 CONFIG_PMECC_CAP=8
 CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_PHY_MICREL=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=0
+CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
 CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
@@ -78,6 +88,9 @@ CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SYSRESET=y
 CONFIG_SYSRESET_AT91=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_QSPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_W1=y
Signature · 1 line
2.25.1
#3 lore raw

PATCH 3/3 configs: at91: sama5d2_icp: enable QSPI and SF command

In reply to Sergiu Moga

Add the configurations required for enabling QSPI and the SF command to allow changes to be made dynamically to serial flash devices from the command line interface.

---
 configs/sama5d2_icp_mmc_defconfig | 13 +++++++++++++
 1 file changed, 13 insertions(+)
configs/sama5d2_icp_mmc_defconfig +13 -0
index bb70c10e25..5598da9a96 100644
@@ -43,6 +43,7 @@ CONFIG_CMD_DM=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 # CONFIG_CMD_LOADS is not set
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
@@ -71,6 +72,15 @@ CONFIG_SYS_I2C_AT91=y
 CONFIG_I2C_EEPROM=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=2
+CONFIG_SF_DEFAULT_SPEED=66000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
 CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
@@ -82,6 +92,9 @@ CONFIG_ATMEL_USART=y
 CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_AT91=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_QSPI=y
 CONFIG_TIMER=y
 CONFIG_SPL_TIMER=y
 CONFIG_ATMEL_TCB_TIMER=y
Signature · 1 line
2.25.1
#4 lore raw
In reply to Sergiu Moga
Quoted 11 lines · Sergiu Moga

This patch series enables the SF command and QSPI for the MMC and NANDFLASH defconfigs in the case of the sam9x60 board and for the MMC defconfig in the case of the sama5d2_icp board. It also changes the compatible of the qspi child node from the board file of sam9x60 so that it can be properly found when probing the bus.

Sergiu Moga (3):
ARM: dts: sam9x60: fix compatible for qspi child node
configs: at91: sam9x60ek: enable QSPI and SF command
configs: at91: sama5d2_icp: enable QSPI and SF command

Quoted 6 lines
  arch/arm/dts/sam9x60ek.dts            |  2 +-
  configs/sam9x60ek_mmc_defconfig       | 13 +++++++++++++
  configs/sam9x60ek_nandflash_defconfig | 13 +++++++++++++
  configs/sama5d2_icp_mmc_defconfig     | 13 +++++++++++++
  4 files changed, 40 insertions(+), 1 deletion(-)

Applied series to u-boot-at91/next , thanks !