ARM: dts: stm32: Add alternate pinmux for DCMI pins
PATCH 1/3 ARM: dts: stm32: Add alternate pinmux for DCMI pins
Add another mux option for DCMI pins, this is used on AV96 board.
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 37 ++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +37 -0
@@ -151,6 +151,43 @@ pins { }; }; + dcmi_pins_c: dcmi-2 { + pins { + pinmux = <STM32_PINMUX('A', 4, AF13)>,/* DCMI_HSYNC */ + <STM32_PINMUX('B', 7, AF13)>,/* DCMI_VSYNC */ + <STM32_PINMUX('A', 6, AF13)>,/* DCMI_PIXCLK */ + <STM32_PINMUX('A', 9, AF13)>,/* DCMI_D0 */ + <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */ + <STM32_PINMUX('E', 0, AF13)>,/* DCMI_D2 */ + <STM32_PINMUX('E', 1, AF13)>,/* DCMI_D3 */ + <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */ + <STM32_PINMUX('I', 4, AF13)>,/* DCMI_D5 */ + <STM32_PINMUX('I', 6, AF13)>,/* DCMI_D6 */ + <STM32_PINMUX('E', 6, AF13)>,/* DCMI_D7 */ + <STM32_PINMUX('I', 1, AF13)>,/* DCMI_D8 */ + <STM32_PINMUX('H', 7, AF13)>;/* DCMI_D9 */ + bias-pull-up; + }; + }; + + dcmi_sleep_pins_c: dcmi-sleep-2 { + pins { + pinmux = <STM32_PINMUX('A', 4, ANALOG)>,/* DCMI_HSYNC */ + <STM32_PINMUX('B', 7, ANALOG)>,/* DCMI_VSYNC */ + <STM32_PINMUX('A', 6, ANALOG)>,/* DCMI_PIXCLK */ + <STM32_PINMUX('A', 9, ANALOG)>,/* DCMI_D0 */ + <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */ + <STM32_PINMUX('E', 0, ANALOG)>,/* DCMI_D2 */ + <STM32_PINMUX('E', 1, ANALOG)>,/* DCMI_D3 */ + <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */ + <STM32_PINMUX('I', 4, ANALOG)>,/* DCMI_D5 */ + <STM32_PINMUX('I', 6, ANALOG)>,/* DCMI_D6 */ + <STM32_PINMUX('E', 6, ANALOG)>,/* DCMI_D7 */ + <STM32_PINMUX('I', 1, ANALOG)>,/* DCMI_D8 */ + <STM32_PINMUX('H', 7, ANALOG)>;/* DCMI_D9 */ + }; + }; + ethernet0_rgmii_pins_a: rgmii-0 { pins1 { pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
Signature · 7 lines
2.35.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 2/3 ARM: dts: stm32: Add alternate pinmux for RCC pin
Add another mux option for RCC pin, this is used on AV96 board for e.g. sensor clock supply.
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +15 -0
@@ -960,6 +960,21 @@ pins { }; }; + mco1_pins_a: mco1-0 { + pins { + pinmux = <STM32_PINMUX('A', 13, AF2)>; /* MCO1 */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + }; + + mco1_sleep_pins_a: mco1-sleep-0 { + pins { + pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* MCO1 */ + }; + }; + mco2_pins_a: mco2-0 { pins { pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
Signature · 7 lines
2.35.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 3/3 ARM: dts: stm32: Add ST MIPID02 bindings to AV96
In reply to Marek VasutAdd DT bindings for ST MIPID02 and DCMI to Avenger96 base DT. Both the ST MIPID02 and DCMI are disabled by default, as the AV96 camera module is optional.
--- .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 55 +++++++++++++++++++ 1 file changed, 55 insertions(+)
arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi +55 -0
@@ -126,6 +126,22 @@ adc2: adc@100 { }; }; +&dcmi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcmi_pins_c>; + pinctrl-1 = <&dcmi_sleep_pins_c>; + status = "disabled"; + + port { + dcmi_0: endpoint { + remote-endpoint = <&stmipi_2>; + bus-type = <5>; + bus-width = <8>; + pclk-sample = <0>; + }; + }; +}; + ðernet0 { status = "okay"; pinctrl-0 = <ðernet0_rgmii_pins_c>;
@@ -219,6 +235,45 @@ &i2c2 { /* X6 I2C2 */ }; &i2c4 { + stmipi: stmipi@14 { + compatible = "st,st-mipid02"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mco1_pins_a>; + pinctrl-1 = <&mco1_sleep_pins_a>; + reg = <0x14>; + clocks = <&rcc CK_MCO1>; + clock-names = "xclk"; + assigned-clocks = <&rcc CK_MCO1>; + assigned-clock-parents = <&rcc CK_HSE>; + assigned-clock-rates = <24000000>; + VDDE-supply = <&v1v8>; + VDDIN-supply = <&v1v8>; + reset-gpios = <&gpioz 0 GPIO_ACTIVE_LOW>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + stmipi_0: endpoint { + }; + }; + + port@2 { + reg = <2>; + stmipi_2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <0>; + remote-endpoint = <&dcmi_0>; + }; + }; + }; + }; + hdmi-transmitter@3d { compatible = "adi,adv7513"; reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
Signature · 7 lines
2.35.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Alexandre TORGUE
maintainerRe: [PATCH 3/3] ARM: dts: stm32: Add ST MIPID02 bindings to AV96
Hi Marek
Quoted 9 lines · Marek Vasut
Add DT bindings for ST MIPID02 and DCMI to Avenger96 base DT. Both the ST MIPID02 and DCMI are disabled by default, as the AV96 camera module is optional.
Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Manivannan Sadhasivam <[email protected]>
Applied on stm32-next.
thanks
Alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel