m68k: Remove dead code
Subsystems (28)
PATCH 1/11 m68k: Remove dead code
There are no mcf5227x platforms, remove the CPU code.
--- arch/m68k/Kconfig | 6 - arch/m68k/cpu/mcf5227x/Makefile | 9 - arch/m68k/cpu/mcf5227x/cpu.c | 67 ---- arch/m68k/cpu/mcf5227x/cpu_init.c | 152 --------- arch/m68k/cpu/mcf5227x/dspi.c | 43 --- arch/m68k/cpu/mcf5227x/interrupts.c | 37 --- arch/m68k/cpu/mcf5227x/speed.c | 127 ------- arch/m68k/cpu/mcf5227x/start.S | 491 ---------------------------- 8 files changed, 932 deletions(-) delete mode 100644 arch/m68k/cpu/mcf5227x/Makefile delete mode 100644 arch/m68k/cpu/mcf5227x/cpu.c delete mode 100644 arch/m68k/cpu/mcf5227x/cpu_init.c delete mode 100644 arch/m68k/cpu/mcf5227x/dspi.c delete mode 100644 arch/m68k/cpu/mcf5227x/interrupts.c delete mode 100644 arch/m68k/cpu/mcf5227x/speed.c delete mode 100644 arch/m68k/cpu/mcf5227x/start.S
arch/m68k/Kconfig +0 -6
@@ -53,12 +53,6 @@ config MCF5441x select DM_SERIAL bool -config MCF5227x - select OF_CONTROL - select DM - select DM_SERIAL - bool - # processor type config M5208 bool
arch/m68k/cpu/mcf5227x/Makefile deleted +0 -9
@@ -1,9 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2004 -# Wolfgang Denk, DENX Software Engineering, [email protected]. - -# ccflags-y += -DET_DEBUG - -extra-y = start.o -obj-y = cpu.o speed.o cpu_init.o interrupts.o dspi.o
arch/m68k/cpu/mcf5227x/cpu.c deleted +0 -67
67 lines not on this page · raw message
arch/m68k/cpu/mcf5227x/cpu_init.c deleted +0 -152
152 lines not on this page · raw message
arch/m68k/cpu/mcf5227x/dspi.c deleted +0 -43
43 lines not on this page · raw message
arch/m68k/cpu/mcf5227x/interrupts.c deleted +0 -37
@@ -1,37 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* -* -* (C) Copyright 2000-2004 -* Wolfgang Denk, DENX Software Engineering, [email protected]. -* -* Copyright (C) 2004-2007, 2012 Freescale Semiconductor, Inc. -* TsiChung Liew ([email protected]) -*/ - -/* CPU specific interrupt routine */ -#include <common.h> -#include <irq_func.h> -#include <asm/immap.h> -#include <asm/io.h> - -int interrupt_init (void ) -{ -int0_t *intp = (int0_t *) (CONFIG_SYS_INTR_BASE ); - -/* Make sure all interrupts are disabled */ -setbits_be32 (&intp->imrh0,0xffffffff ); -setbits_be32 (&intp->imrl0,0xffffffff ); - -enable_interrupts (); -return 0 ; -} - -#if defined(CONFIG_MCFTMR ) -void dtimer_intr_setup (void ) -{ -int0_t *intp = (int0_t *) (CONFIG_SYS_INTR_BASE ); - -out_8 (&intp->icr0[CONFIG_SYS_TMRINTR_NO ],CONFIG_SYS_TMRINTR_PRI ); -clrbits_be32 (&intp->imrh0,CONFIG_SYS_TMRINTR_MASK ); -} -#endif
arch/m68k/cpu/mcf5227x/speed.c deleted +0 -127
127 lines not on this page · raw message
arch/m68k/cpu/mcf5227x/start.S deleted +0 -491
491 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH 2/11 arm: pxa: Remove CONFIG_CPU_PXA25X
There are no platforms that set this, remove the code.
--- arch/arm/cpu/pxa/Makefile | 1 - arch/arm/cpu/pxa/cpuinfo.c | 6 - arch/arm/cpu/pxa/start.S | 111 +- arch/arm/include/asm/arch-pxa/config.h | 2 - arch/arm/include/asm/config.h | 1 - drivers/mmc/pxa_mmc_gen.c | 7 +- drivers/net/smc91111.h | 152 +- drivers/serial/serial_pxa.c | 1 - drivers/usb/gadget/Makefile | 1 - drivers/usb/gadget/pxa25x_udc.c | 2049 ------------------------ drivers/usb/gadget/pxa25x_udc.h | 149 -- include/dm/platform_data/serial_pxa.h | 15 - include/lcd.h | 3 +- 13 files changed, 6 insertions(+), 2492 deletions(-) delete mode 100644 drivers/usb/gadget/pxa25x_udc.c delete mode 100644 drivers/usb/gadget/pxa25x_udc.h
arch/arm/cpu/pxa/Makefile +0 -1
@@ -5,7 +5,6 @@ extra-y = start.o -obj-$(CONFIG_CPU_PXA25X) += pxa2xx.o obj-$(CONFIG_CPU_PXA27X) += pxa2xx.o obj-y += cpuinfo.o
arch/arm/cpu/pxa/cpuinfo.c +0 -6
@@ -11,12 +11,6 @@#include <errno.h> #include <linux/compiler.h> -#ifdef CONFIG_CPU_PXA25X -#if ((CONFIG_SYS_INIT_SP_ADDR ) !=0xfffff800 ) -#error "Init SP address must be set to 0xfffff800 for PXA250" -#endif -#endif -#define CPU_MASK_PXA_PRODID 0x000003f0#define CPU_MASK_PXA_REVID 0x0000000f
arch/arm/cpu/pxa/start.S +2 -109
133 lines not on this page · raw message
arch/arm/include/asm/arch-pxa/config.h +0 -2
@@ -13,8 +13,6 @@*/ #if defined(CONFIG_CPU_PXA27X ) || defined(CONFIG_CPU_MONAHANS )#define CONFIG_SYS_TIMER_RATE 3250000 -#elif defined(CONFIG_CPU_PXA25X ) -#define CONFIG_SYS_TIMER_RATE 3686400#else #error "Timer frequency unknown - please config PXA CPU type"#endif
arch/arm/include/asm/config.h +0 -1
@@ -11,7 +11,6 @@#if defined(CONFIG_ARCH_LS1021A ) || \ defined(CONFIG_CPU_PXA27X ) || \ defined(CONFIG_CPU_MONAHANS ) || \ - defined(CONFIG_CPU_PXA25X ) || \ defined(CONFIG_FSL_LAYERSCAPE )#include <asm/arch/config.h> #endif
drivers/mmc/pxa_mmc_gen.c +1 -6
@@ -20,12 +20,7 @@#include <mmc.h> /* PXAMMC Generic default config for various CPUs */ -#if defined(CONFIG_CPU_PXA25X ) -#define PXAMMC_FIFO_SIZE 1 -#define PXAMMC_MIN_SPEED 312500 -#define PXAMMC_MAX_SPEED 20000000 -#define PXAMMC_HOST_CAPS (0) -#elif defined(CONFIG_CPU_PXA27X ) +#if defined(CONFIG_CPU_PXA27X )#define PXAMMC_CRC_SKIP #define PXAMMC_FIFO_SIZE 32#define PXAMMC_MIN_SPEED 304000
drivers/net/smc91111.h +2 -150
164 lines not on this page · raw message
drivers/serial/serial_pxa.c +0 -1
@@ -88,7 +88,6 @@ static struct pxa_uart_regs *pxa_uart_index_to_regs(uint32_t uart_index)case FFUART_INDEX :return (struct pxa_uart_regs *)FFUART_BASE ;case BTUART_INDEX :return (struct pxa_uart_regs *)BTUART_BASE ;case STUART_INDEX :return (struct pxa_uart_regs *)STUART_BASE ; -case HWUART_INDEX :return (struct pxa_uart_regs *)HWUART_BASE ;default :return NULL ; }
drivers/usb/gadget/Makefile +0 -1
@@ -37,7 +37,6 @@ ifdef CONFIG_USB_ETHER obj-y += ether.o obj-$(CONFIG_USB_ETH_RNDIS) += rndis.o obj-$(CONFIG_CI_UDC) += ci_udc.o -obj-$(CONFIG_CPU_PXA25X) += pxa25x_udc.o else # Devices not related to the new gadget layer depend on CONFIG_USB_DEVICE ifdef CONFIG_USB_DEVICE
drivers/usb/gadget/pxa25x_udc.c deleted +0 -2049
2,049 lines not on this page · raw message
drivers/usb/gadget/pxa25x_udc.h deleted +0 -149
149 lines not on this page · raw message
include/dm/platform_data/serial_pxa.h +0 -15
@@ -16,13 +16,6 @@#define BTUART_INDEX 0#define FFUART_INDEX 1#define STUART_INDEX 2 -#elif CONFIG_CPU_PXA25X -#define UART_CLK_BASE BIT(4)/* HWUART */ -#define UART_CLK_REG CKEN -#define HWUART_INDEX 0 -#define STUART_INDEX 1 -#define FFUART_INDEX 2 -#define BTUART_INDEX 3#else /* PXA27x */ #define UART_CLK_BASE CKEN5_STUART#define UART_CLK_REG CKEN
@@ -31,14 +24,6 @@#define BTUART_INDEX 2#endif -/* -* Only PXA250 has HWUART, to avoid poluting the code with more macros, -* artificially introduce this. -*/ -#ifndef CONFIG_CPU_PXA25X -#define HWUART_INDEX 0xff -#endif -/* * struct pxa_serial_plat - information about a PXA port *
include/lcd.h +1 -2
@@ -40,8 +40,7 @@ ulong lcd_setmem(ulong addr);*/ void lcd_set_flush_dcache (int flush); -#if defined(CONFIG_CPU_PXA25X ) || defined(CONFIG_CPU_PXA27X ) || \ - definedCONFIG_CPU_MONAHANS +#if defined(CONFIG_CPU_PXA27X ) || definedCONFIG_CPU_MONAHANS #include <pxa_lcd.h> #elif defined(CONFIG_ATMEL_LCD ) || defined(CONFIG_ATMEL_HLCD )#include <atmel_lcd.h>
Signature · 1 line
2.25.1
PATCH 3/11 mvebu: Use CONFIG_SPL_STACK + 4 directly for bootparam location
In reply to Tom RiniThe definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This change will make it clear where the location is still, once CONFIG_SPL_STACK moves to Kconfig.
--- arch/arm/mach-mvebu/lowlevel_spl.S | 8 ++++---- arch/arm/mach-mvebu/spl.c | 2 +- include/configs/clearfog.h | 1 - include/configs/controlcenterdc.h | 1 - include/configs/db-88f6720.h | 1 - include/configs/db-88f6820-amc.h | 1 - include/configs/db-88f6820-gp.h | 1 - include/configs/db-mv784mp-gp.h | 1 - include/configs/ds414.h | 1 - include/configs/helios4.h | 1 - include/configs/maxbcm.h | 1 - include/configs/theadorable.h | 1 - include/configs/turris_omnia.h | 1 - include/configs/x530.h | 1 - 14 files changed, 5 insertions(+), 17 deletions(-)
arch/arm/mach-mvebu/lowlevel_spl.S +4 -4
@@ -8,19 +8,19 @@ * contains U-Boot SPL, optionally it can also contain additional arguments. * The number of these arguments is in r0, pointer to the argument array in r1. * BootROM expects executable BIN header code to return to address stored in lr. - * Other registers (r2 - r12) must be preserved. We save all registers to - * CONFIG_SPL_BOOTROM_SAVE address. BIN header arguments (passed via r0 and r1) + * Other registers (r2 - r12) must be preserved. We save all registers to the + * address of CONFIG_SPL_STACK + 4. BIN header arguments (passed via r0 and r1) * are currently not used by U-Boot SPL binary. */ ENTRY(save_boot_params) stmfd sp!, {r0 - r12, lr} /* @ save registers on stack */ - ldr r12, =CONFIG_SPL_BOOTROM_SAVE + ldr r12, =(CONFIG_SPL_STACK + 4) str sp, [r12] b save_boot_params_ret ENDPROC(save_boot_params) ENTRY(return_to_bootrom) - ldr r12, =CONFIG_SPL_BOOTROM_SAVE + ldr r12, =(CONFIG_SPL_STACK + 4) ldr sp, [r12] ldmfd sp!, {r0 - r12, lr} /* @ restore registers from stack */ mov r0, #0x0 /* @ return value: 0x0 NO_ERR */
arch/arm/mach-mvebu/spl.c +1 -1
@@ -283,7 +283,7 @@ u32 spl_boot_device(void)int board_return_to_bootrom (struct spl_image_info *spl_image,struct spl_boot_device *bootdev) { -u32 *regs = *(u32 **)CONFIG_SPL_BOOTROM_SAVE ; +u32 *regs = *(u32 **)(CONFIG_SPL_STACK +4 );printf ("Returning to BootROM (return address 0x%08x)...\n" , regs[13 ]);return_to_bootrom ();
include/configs/clearfog.h +0 -1
@@ -48,7 +48,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA )/* SPL related MMC defines */
include/configs/controlcenterdc.h +0 -1
@@ -40,7 +40,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#if CONFIG_SPL_BOOT_DEVICE ==SPL_BOOT_SDIO_MMC_CARD /* SPL related MMC defines */
include/configs/db-88f6720.h +0 -1
@@ -38,6 +38,5 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#endif /* _CONFIG_DB_88F6720_H */
include/configs/db-88f6820-amc.h +0 -1
@@ -45,7 +45,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)/* * mv-common.h should be defined after CMD configs since it used them
include/configs/db-88f6820-gp.h +0 -1
@@ -45,7 +45,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#if CONFIG_SPL_BOOT_DEVICE ==SPL_BOOT_SDIO_MMC_CARD /* SPL related MMC defines */
include/configs/db-mv784mp-gp.h +0 -1
@@ -57,7 +57,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */ #define CONFIG_SPD_EEPROM 0x4e
include/configs/ds414.h +0 -1
@@ -49,7 +49,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)/* Default Environment */
include/configs/helios4.h +0 -1
@@ -48,7 +48,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA )/* SPL related MMC defines */
include/configs/maxbcm.h +0 -1
@@ -52,7 +52,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)/* SPL related SPI defines */
include/configs/theadorable.h +0 -1
@@ -77,7 +77,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */ #define CONFIG_SYS_SDRAM_SIZE SZ_2G
include/configs/turris_omnia.h +0 -1
@@ -32,7 +32,6 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC /* SPL related MMC defines */
include/configs/x530.h +0 -1
@@ -72,6 +72,5 @@#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) -#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)#endif /* _CONFIG_X530_H */
Signature · 1 line
2.25.1
PATCH 4/11 arm: Use CONFIG_SPL_STACK or CONFIG_SYS_INIT_SP_ADDR directly.
In reply to Tom RiniIn some cases, we define CONFIG_SYS_INIT_SP_ADDR differently for SPL or full U-Boot. This case should be making use of CONFIG_SPL_STACK, as that's what that variable is for. In a few other cases we define CONFIG_SPL_STACK directly to CONFIG_SYS_INIT_SP_ADDR, but do not need to as the code handles this correctly, normally.
--- include/configs/imxrt1020-evk.h | 5 ----- include/configs/imxrt1050-evk.h | 5 ----- include/configs/sam9x60_curiosity.h | 5 +---- include/configs/sama5d27_som1_ek.h | 5 +---- include/configs/sama5d27_wlsom1_ek.h | 5 +---- include/configs/sama5d2_icp.h | 5 +---- include/configs/sama5d2_xplained.h | 5 +---- include/configs/sama5d3_xplained.h | 5 +---- include/configs/sama5d3xek.h | 5 +---- include/configs/sama5d4_xplained.h | 5 +---- include/configs/sama5d4ek.h | 5 +---- include/configs/sama7g5ek.h | 5 +---- include/configs/smartweb.h | 5 +---- include/configs/socfpga_soc64_common.h | 10 +++------- include/configs/stm32f746-disco.h | 5 ----- 15 files changed, 14 insertions(+), 66 deletions(-)
include/configs/imxrt1020-evk.h +0 -5
@@ -24,12 +24,7 @@* Configuration of the external SDRAM memory */ -/* For SPL */ -#ifdef CONFIG_SUPPORT_SPL -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR#define CONFIG_SYS_SPL_LEN 0x00008000#define CONFIG_SYS_UBOOT_START 0x800023FD -#endif -/* For SPL ends */ #endif /* __IMXRT1020_EVK_H */
include/configs/imxrt1050-evk.h +0 -5
@@ -31,12 +31,7 @@* Configuration of the external SDRAM memory */ -/* For SPL */ -#ifdef CONFIG_SUPPORT_SPL -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR#define CONFIG_SYS_SPL_LEN 0x00008000#define CONFIG_SYS_UBOOT_START 0x800023FD -#endif -/* For SPL ends */ #endif /* __IMXRT1050_EVK_H */
include/configs/sam9x60_curiosity.h +1 -4
@@ -20,12 +20,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x8000000/* 128 MB */ -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 + CONFIG_SYS_MALLOC_F_LEN - \ GENERATED_GBL_DATA_SIZE) -#endif #endif
include/configs/sama5d27_som1_ek.h +1 -4
@@ -14,14 +14,11 @@#undef CONFIG_SYS_AT91_MAIN_CLOCK#define CONFIG_SYS_AT91_MAIN_CLOCK 24000000/* from 24 MHz crystal */ -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else #define CONFIG_SYS_INIT_SP_ADDR \ (0x22000000 + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* SPL */ +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SPL_BSS_START_ADDR 0x20000000#define CONFIG_SYS_SPL_MALLOC_START 0x20080000#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
include/configs/sama5d27_wlsom1_ek.h +1 -4
@@ -19,14 +19,11 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x10000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* SPL */ +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SPL_BSS_START_ADDR 0x20000000#define CONFIG_SYS_SPL_MALLOC_START 0x20080000#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
include/configs/sama5d2_icp.h +1 -4
@@ -18,12 +18,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x20000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif #ifdef CONFIG_SD_BOOT /* u-boot env in sd/mmc card */
include/configs/sama5d2_xplained.h +1 -4
@@ -11,14 +11,11 @@#include "at91-sama5_common.h" -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else #define CONFIG_SYS_INIT_SP_ADDR \ (0x22000000 + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* SPL */ +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SPL_BSS_START_ADDR 0x20000000#define CONFIG_SYS_SPL_MALLOC_START 0x20080000#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
include/configs/sama5d3_xplained.h +1 -4
@@ -27,12 +27,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x10000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x318000 -#else +#define CONFIG_SPL_STACK 0x318000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* NAND flash */ #ifdef CONFIG_CMD_NAND
include/configs/sama5d3xek.h +1 -4
@@ -38,12 +38,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x20000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x318000 -#else +#define CONFIG_SPL_STACK 0x318000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* SerialFlash */
include/configs/sama5d4_xplained.h +1 -4
@@ -15,12 +15,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x20000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* NAND flash */ #ifdef CONFIG_CMD_NAND
include/configs/sama5d4ek.h +1 -4
@@ -15,12 +15,9 @@#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_SDRAM_SIZE 0x20000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) -#endif /* NAND flash */ #ifdef CONFIG_CMD_NAND
include/configs/sama7g5ek.h +1 -4
@@ -16,12 +16,9 @@#define CONFIG_SYS_SDRAM_BASE 0x60000000#define CONFIG_SYS_SDRAM_SIZE 0x20000000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x218000 -#else +#define CONFIG_SPL_STACK 0x218000#define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 + CONFIG_SYS_MALLOC_F_LEN - \ GENERATED_GBL_DATA_SIZE) -#endif #endif
include/configs/smartweb.h +1 -4
@@ -104,9 +104,6 @@ \"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x301000 -#else /* * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, * leaving the correct space for initial global data structure above that
@@ -114,10 +111,10 @@*/ #define CONFIG_SYS_INIT_SP_ADDR \ (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) -#endif /* Defines for SPL */ +#define CONFIG_SPL_STACK 0x301000#define CONFIG_SPL_BSS_START_ADDR CONFIG_SYS_SDRAM_BASE#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ CONFIG_SPL_BSS_MAX_SIZE)
include/configs/socfpga_soc64_common.h +3 -7
@@ -29,14 +29,8 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000#define CONFIG_SYS_INIT_RAM_SIZE 0x40000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR \ - + CONFIG_SYS_INIT_RAM_SIZE \ - - SOC64_HANDOFF_SIZE) -#else #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE \ + 0x100000) -#endif #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_SP_ADDR)/*
@@ -153,7 +147,9 @@ unsigned int cm_get_l4_sys_free_clk_hz(void);* */ #define CONFIG_SPL_TARGET "spl/u-boot-spl-dtb.hex" -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#define CONFIG_SPL_STACK (CONFIG_SYS_INIT_RAM_ADDR \ + + CONFIG_SYS_INIT_RAM_SIZE \ + - SOC64_HANDOFF_SIZE)#define CONFIG_SPL_BSS_START_ADDR (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE \ - CONFIG_SPL_BSS_MAX_SIZE)#define CONFIG_SYS_SPL_MALLOC_SIZE (CONFIG_SYS_MALLOC_LEN)
include/configs/stm32f746-disco.h +0 -5
@@ -39,9 +39,6 @@"ramdisk_addr_r=0xC0438000\0" \ BOOTENV -/* For SPL */ -#ifdef CONFIG_SUPPORT_SPL -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR#define CONFIG_SYS_MONITOR_LEN (512 * 1024)#define CONFIG_SYS_SPL_LEN 0x00008000#define CONFIG_SYS_UBOOT_START 0x080083FD
@@ -51,8 +48,6 @@/* DT blob (fdt) address */ #define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \ 0x1C0000) -#endif -/* For SPL ends */ /* For splashcreen */
Signature · 1 line
2.25.1
PATCH 5/11 arm: Stop using CONFIG_SYS_GBL_DATA_OFFSET
In reply to Tom RiniThis value is only referenced by PowerPC code in a way other than directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR directly.
--- include/configs/integrator-common.h | 3 +-- include/configs/vexpress_common.h | 3 +-- 2 files changed, 2 insertions(+), 4 deletions(-)
include/configs/integrator-common.h +1 -2
@@ -32,10 +32,9 @@#define PHYS_SDRAM_1_SIZE 0x08000000/* 128 MB */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET/* * FLASH and environment organization
include/configs/vexpress_common.h +1 -2
@@ -139,10 +139,9 @@/* additions for new relocation code */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET/* Basic environment settings */ #define BOOT_TARGET_DEVICES (func) \
Signature · 1 line
2.25.1
PATCH 6/11 m68k: Stop using CONFIG_SYS_GBL_DATA_OFFSET
In reply to Tom RiniThis value is only referenced by PowerPC code in a way other than directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR directly.
--- include/configs/M5208EVBE.h | 3 +-- include/configs/M5235EVB.h | 3 +-- include/configs/M5249EVB.h | 3 +-- include/configs/M5253DEMO.h | 3 +-- include/configs/M5272C3.h | 3 +-- include/configs/M5275EVB.h | 3 +-- include/configs/M5282EVB.h | 3 +-- include/configs/M53017EVB.h | 3 +-- include/configs/M5329EVB.h | 3 +-- include/configs/M5373EVB.h | 3 +-- include/configs/amcore.h | 3 +-- include/configs/astro_mcf5373l.h | 3 +-- include/configs/cobra5272.h | 3 +-- include/configs/eb_cpu5282.h | 3 +-- include/configs/stmark2.h | 3 +-- 15 files changed, 15 insertions(+), 30 deletions(-)
include/configs/M5208EVBE.h +1 -2
@@ -65,8 +65,7 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000#define CONFIG_SYS_INIT_RAM_SIZE 0x4000/* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)/* * Start addresses for the final memory configuration
include/configs/M5235EVB.h +1 -2
@@ -75,8 +75,7 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x10000/* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x21 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE - 0x10)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/M5249EVB.h +1 -2
@@ -44,8 +44,7 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)#define LDS_BOARD_TEXT \ . = DEFINED(env_offset) ? env_offset : .; \
include/configs/M5253DEMO.h +1 -2
@@ -79,8 +79,7 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x10000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)/* * Start addresses for the final memory configuration
include/configs/M5272C3.h +1 -2
@@ -76,8 +76,7 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/M5275EVB.h +1 -2
@@ -78,8 +78,7 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x10000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/M5282EVB.h +1 -2
@@ -77,8 +77,7 @@*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x10000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/M53017EVB.h +1 -2
@@ -79,8 +79,7 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000#define CONFIG_SYS_INIT_RAM_SIZE 0x20000/* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)/* * Start addresses for the final memory configuration
include/configs/M5329EVB.h +1 -2
@@ -75,8 +75,7 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000#define CONFIG_SYS_INIT_RAM_SIZE 0x8000/* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/M5373EVB.h +1 -2
@@ -77,8 +77,7 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000#define CONFIG_SYS_INIT_RAM_SIZE 0x8000/* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/amcore.h +1 -2
@@ -32,9 +32,8 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000/* size of internal SRAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET#define CONFIG_SYS_SDRAM_BASE 0x00000000#define CONFIG_SYS_SDRAM_SIZE 0x1000000
include/configs/astro_mcf5373l.h +1 -2
@@ -162,9 +162,8 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000#define CONFIG_SYS_INIT_RAM_SIZE 0x8000#define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET/* * Start addresses for the final memory configuration
include/configs/cobra5272.h +1 -2
@@ -165,8 +165,7 @@ enter a valid image address in flash */*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/eb_cpu5282.h +1 -2
@@ -65,9 +65,8 @@#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 -#define CONFIG_SYS_GBL_DATA_OFFSET \ +#define CONFIG_SYS_INIT_SP_OFFSET \ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET/*----------------------------------------------------------------------- * Start addresses for the final memory configuration
include/configs/stmark2.h +1 -2
@@ -54,9 +54,8 @@/* End of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x10000#define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ +#define CONFIG_SYS_INIT_SP_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) - 32) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32)/*
Signature · 1 line
2.25.1
PATCH 7/11 mpc85xx: Switch to setting the initial stack pointer more clearly
In reply to Tom RiniCurrently, since we know that in the combination of CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET all of the "high" bits are in CONFIG_SYS_INIT_RAM_ADDR and "low" bits are in CONFIG_SYS_GBL_DATA_OFFSET we reference this separately in start.S, but added together everywhere else. For clarity consistency, reference the combined value here instead.
--- arch/powerpc/cpu/mpc85xx/start.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/powerpc/cpu/mpc85xx/start.S +2 -2
@@ -1160,8 +1160,8 @@ _start_cont: bne 1b #if CONFIG_VAL(SYS_MALLOC_F_LEN) - lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h - ori r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l + lis r4,(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h + ori r4,r4,(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@l addi r3,r3,16 /* Pre-relocation malloc area */ stw r3,GD_MALLOC_BASE(r4)
Signature · 1 line
2.25.1
PATCH 8/11 powerpc: Switch to using CONFIG_SYS_INIT_SP_OFFSET from CONFIG_SYS_GBL_DATA_OFFSET
In reply to Tom RiniIn the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for consistency with other architectures.
--- README | 18 ------------------ arch/powerpc/cpu/mpc83xx/cpu_init.c | 2 +- arch/powerpc/cpu/mpc83xx/spl_minimal.c | 2 +- arch/powerpc/cpu/mpc83xx/start.S | 4 ++-- arch/powerpc/cpu/mpc85xx/cpu_init_early.c | 2 +- arch/powerpc/cpu/mpc85xx/start.S | 4 ++-- include/configs/MPC837XERDB.h | 4 ++-- include/configs/MPC8548CDS.h | 4 ++-- include/configs/P1010RDB.h | 5 ++--- include/configs/P2041RDB.h | 5 ++--- include/configs/T102xRDB.h | 5 ++--- include/configs/T104xRDB.h | 5 ++--- include/configs/T208xQDS.h | 5 ++--- include/configs/T208xRDB.h | 5 ++--- include/configs/T4240RDB.h | 5 ++--- include/configs/corenet_ds.h | 4 ++-- include/configs/gazerbeam.h | 4 ++-- include/configs/ids8313.h | 6 ++---- include/configs/km/km-mpc83xx.h | 4 ++-- include/configs/kmcent2.h | 5 ++--- include/configs/p1_p2_rdb_pc.h | 5 ++--- include/configs/qemu-ppce500.h | 5 ++--- include/configs/socrates.h | 4 ++-- 23 files changed, 41 insertions(+), 71 deletions(-)
README +0 -18
@@ -2130,24 +2130,6 @@ Low Level (hardware related) configuration options: U-Boot uses the following memory types: - MPC8xx: IMMR (internal memory of the CPU) -- CONFIG_SYS_GBL_DATA_OFFSET: - - Offset of the initial data structure in the memory - area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually - CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial - data is located at the end of the available space - (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE - - GENERATED_GBL_DATA_SIZE), and the initial stack is just - below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR + - CONFIG_SYS_GBL_DATA_OFFSET) downward. - - Note: - On the MPC824X (or other systems that use the data - cache for initial memory) the address chosen for - CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must - point to an otherwise UNUSED address space between - the top of RAM and the start of the PCI space. - - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27) - CONFIG_SYS_OR_TIMING_SDRAM:
arch/powerpc/cpu/mpc83xx/cpu_init.c +1 -1
@@ -138,7 +138,7 @@ void cpu_init_f (volatile immap_t * im)0 ;/* Pointer is writable since we allocated a register for it */ - gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR +CONFIG_SYS_GBL_DATA_OFFSET ); + gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ;/* global data region was cleared in start.S */
arch/powerpc/cpu/mpc83xx/spl_minimal.c +1 -1
@@ -25,7 +25,7 @@ DECLARE_GLOBAL_DATA_PTR;void cpu_init_f (volatile immap_t * im) {/* Pointer is writable since we allocated a register for it */ - gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR +CONFIG_SYS_GBL_DATA_OFFSET ); + gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ;/* global data region was cleared in start.S */
arch/powerpc/cpu/mpc83xx/start.S +2 -2
@@ -229,8 +229,8 @@ in_flash: /* set up the stack pointer in our newly created * cache-ram; use r3 to keep the new SP for now to * avoid overiding the SP it uselessly */ - lis r3, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h - ori r3, r3, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@l + lis r3, CONFIG_SYS_INIT_SP_ADDR@h + ori r3, r3, CONFIG_SYS_INIT_SP_ADDR@l /* r4 = end of GD area */ addi r4, r3, GENERATED_GBL_DATA_SIZE
arch/powerpc/cpu/mpc85xx/cpu_init_early.c +1 -1
@@ -94,7 +94,7 @@ void cpu_init_early_f(void *fdt)#endif /* Pointer is writable since we allocated a register for it */ - gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR +CONFIG_SYS_GBL_DATA_OFFSET ); + gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ;/* gd area was zeroed during startup */
arch/powerpc/cpu/mpc85xx/start.S +2 -2
@@ -1160,8 +1160,8 @@ _start_cont: bne 1b #if CONFIG_VAL(SYS_MALLOC_F_LEN) - lis r4,(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h - ori r4,r4,(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@l + lis r4,CONFIG_SYS_INIT_SP_ADDR@h + ori r4,r4,CONFIG_SYS_INIT_SP_ADDR@l addi r3,r3,16 /* Pre-relocation malloc area */ stw r3,GD_MALLOC_BASE(r4)
include/configs/MPC837XERDB.h +2 -2
@@ -141,8 +141,8 @@#define CONFIG_SYS_INIT_RAM_LOCK 1#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000/* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)/* * FLASH on the Local Bus
include/configs/MPC8548CDS.h +2 -2
@@ -244,8 +244,8 @@#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000/* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x4000/* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
include/configs/P1010RDB.h +2 -3
@@ -380,9 +380,8 @@ extern unsigned long get_sdram_size(void);#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000/* stack in RAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/P2041RDB.h +2 -3
@@ -196,9 +196,8 @@#endif #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/T102xRDB.h +2 -3
@@ -329,9 +329,8 @@#endif #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/T104xRDB.h +2 -3
@@ -307,9 +307,8 @@ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/T208xQDS.h +2 -3
@@ -302,9 +302,8 @@ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH *1ull <<32 ) | \ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)/*
include/configs/T208xRDB.h +2 -3
@@ -261,9 +261,8 @@ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH *1ull <<32 ) | \ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)/*
include/configs/T4240RDB.h +2 -3
@@ -103,9 +103,8 @@ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/corenet_ds.h +2 -2
@@ -194,8 +194,8 @@#endif #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/gazerbeam.h +2 -2
@@ -33,8 +33,8 @@#define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000/* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)/* * FLASH on the Local Bus
include/configs/ids8313.h +2 -4
@@ -28,10 +28,8 @@#define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000#define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x100 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)/* * Internal Definitions
include/configs/km/km-mpc83xx.h +2 -2
@@ -38,8 +38,8 @@#define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000/* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000/* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)/* * Init Local Bus Memory Controller: *
include/configs/kmcent2.h +2 -3
@@ -339,9 +339,8 @@ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN 0xc0000/* 768k */
include/configs/p1_p2_rdb_pc.h +2 -3
@@ -284,9 +284,8 @@/* Size of used area in RAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
include/configs/qemu-ppce500.h +2 -3
@@ -56,9 +56,8 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void); CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
include/configs/socrates.h +2 -2
@@ -103,8 +103,8 @@#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000/* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x4000/* Size used area in RAM*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)#define CONFIG_SYS_MONITOR_LEN (384 * 1024)/* Reserve 384KiB for Mon */
Signature · 1 line
2.25.1
PATCH 9/11 stih410-b2260: Switch to using GENERATED_GBL_DATA_SIZE
In reply to Tom RiniWe have GENERATED_GBL_DATA_SIZE to tell us how large the generated global data is, so do not use a hard-coded value of 1024 for it.
--- include/configs/stih410-b2260.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
include/configs/stih410-b2260.h +1 -2
@@ -42,10 +42,9 @@/* Extra Commands */ -#define CONFIG_SYS_GBL_DATA_SIZE 1024/* Global data structures */ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ CONFIG_SYS_MALLOC_LEN - \ - CONFIG_SYS_GBL_DATA_SIZE) + GENERATED_GBL_DATA_SIZE)/* USB Configs */ #define CONFIG_USB_OHCI_NEW
Signature · 1 line
2.25.1
PATCH 10/11 Introduce include/system-constants.h
In reply to Tom RiniWe have a number of CONFIG symbols today that are of the form:
SYM1 = CONST1 + CONST2
or other static math operations (shifts, etc). The issue is that by moving these to Kconfig we no longer have the ability to calculate these values, so they become less flexible and useful. It's also the case that sometimes a platform will just define SYM1 directly or perform a slightly different set of calculations. We introduce this header now to have a place to start to handle these cases.
--- include/system-constants.h | 6 ++++++ 1 file changed, 6 insertions(+) create mode 100644 include/system-constants.h
include/system-constants.h new file +6 -0
@@ -0,0 +1,6 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef __SYSTEM_CONSTANTS_H__ +#define __SYSTEM_CONSTANTS_H__ + +#endif
Signature · 1 line
2.25.1
PATCH 11/11 Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h
In reply to Tom Rini- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files.
--- Kconfig | 18 ++++++++++++++++++ README | 6 ------ arch/arc/lib/start.S | 3 ++- arch/arm/cpu/arm926ejs/mxs/start.S | 3 ++- arch/arm/cpu/armv7/lowlevel_init.S | 3 ++- arch/arm/cpu/armv7/start.S | 3 ++- arch/arm/lib/crt0.S | 3 ++- arch/arm/lib/crt0_64.S | 3 ++- arch/arm/lib/vectors_m.S | 3 ++- arch/arm/mach-kirkwood/include/mach/config.h | 3 --- arch/arm/mach-mvebu/include/mach/config.h | 3 --- arch/arm/mach-rmobile/lowlevel_init.S | 1 + arch/arm/mach-rmobile/lowlevel_init_ca15.S | 3 ++- .../mach-uniphier/arm32/late_lowlevel_init.S | 3 ++- arch/mips/cpu/start.S | 8 ++------ arch/mips/mach-mtmips/mt7628/lowlevel_init.S | 11 +++-------- arch/powerpc/cpu/mpc83xx/cpu_init.c | 3 ++- arch/powerpc/cpu/mpc83xx/spl_minimal.c | 3 ++- arch/powerpc/cpu/mpc83xx/start.S | 5 +++-- arch/powerpc/cpu/mpc85xx/cpu_init_early.c | 3 ++- arch/powerpc/cpu/mpc85xx/start.S | 5 +++-- arch/riscv/cpu/start.S | 3 ++- board/synopsys/iot_devkit/u-boot.lds | 1 + configs/SBx81LIFKW_defconfig | 2 ++ configs/SBx81LIFXCAT_defconfig | 2 ++ configs/a3y17lte_defconfig | 2 ++ configs/a5y17lte_defconfig | 2 ++ configs/a7y17lte_defconfig | 2 ++ configs/ae350_rv32_defconfig | 2 ++ configs/ae350_rv32_spl_defconfig | 2 ++ configs/ae350_rv32_spl_xip_defconfig | 2 ++ configs/ae350_rv32_xip_defconfig | 2 ++ configs/ae350_rv64_defconfig | 2 ++ configs/ae350_rv64_spl_defconfig | 2 ++ configs/ae350_rv64_spl_xip_defconfig | 2 ++ configs/ae350_rv64_xip_defconfig | 2 ++ configs/alt_defconfig | 2 ++ configs/am335x_baltos_defconfig | 2 ++ configs/am335x_boneblack_vboot_defconfig | 2 ++ configs/am335x_evm_defconfig | 2 ++ configs/am335x_evm_spiboot_defconfig | 2 ++ configs/am335x_guardian_defconfig | 2 ++ configs/am335x_hs_evm_defconfig | 2 ++ configs/am335x_hs_evm_uart_defconfig | 2 ++ configs/am335x_igep003x_defconfig | 2 ++ configs/am335x_pdu001_defconfig | 2 ++ configs/am335x_shc_defconfig | 2 ++ configs/am335x_shc_ict_defconfig | 2 ++ configs/am335x_shc_netboot_defconfig | 2 ++ configs/am335x_shc_sdboot_defconfig | 2 ++ configs/am335x_sl50_defconfig | 2 ++ configs/am3517_evm_defconfig | 2 ++ configs/am43xx_evm_defconfig | 2 ++ configs/am43xx_evm_qspiboot_defconfig | 2 ++ configs/am43xx_evm_rtconly_defconfig | 2 ++ configs/am43xx_evm_usbhost_boot_defconfig | 2 ++ configs/am43xx_hs_evm_defconfig | 2 ++ configs/am57xx_evm_defconfig | 2 ++ configs/am57xx_hs_evm_defconfig | 2 ++ configs/am57xx_hs_evm_usb_defconfig | 2 ++ configs/am64x_evm_a53_defconfig | 2 ++ configs/am64x_evm_r5_defconfig | 2 ++ configs/am65x_evm_a53_defconfig | 2 ++ configs/am65x_evm_r5_defconfig | 2 ++ configs/am65x_evm_r5_usbdfu_defconfig | 2 ++ configs/am65x_evm_r5_usbmsc_defconfig | 2 ++ configs/am65x_hs_evm_a53_defconfig | 2 ++ configs/am65x_hs_evm_r5_defconfig | 2 ++ configs/ap121_defconfig | 2 ++ configs/ap143_defconfig | 2 ++ configs/ap152_defconfig | 2 ++ configs/apalis-imx8_defconfig | 2 ++ configs/armadillo-800eva_defconfig | 2 ++ configs/arndale_defconfig | 2 ++ configs/at91sam9m10g45ek_mmc_defconfig | 2 ++ configs/at91sam9m10g45ek_nandflash_defconfig | 2 ++ configs/at91sam9n12ek_mmc_defconfig | 2 ++ configs/at91sam9n12ek_nandflash_defconfig | 2 ++ configs/at91sam9n12ek_spiflash_defconfig | 2 ++ configs/at91sam9x5ek_dataflash_defconfig | 2 ++ configs/at91sam9x5ek_mmc_defconfig | 2 ++ configs/at91sam9x5ek_nandflash_defconfig | 2 ++ configs/at91sam9x5ek_spiflash_defconfig | 2 ++ ...zedev_cc_v1_0_ultrazedev_som_v1_0_defconfig | 2 ++ configs/axs101_defconfig | 2 ++ configs/axs103_defconfig | 2 ++ configs/bananapi-m5_defconfig | 2 ++ configs/bcm963158_ram_defconfig | 2 ++ configs/bcm96753ref_ram_defconfig | 2 ++ configs/bcm968360bg_ram_defconfig | 2 ++ configs/bcm968580xref_ram_defconfig | 2 ++ configs/bcm_ns3_defconfig | 2 ++ configs/beelink-gsking-x_defconfig | 2 ++ configs/beelink-gtking_defconfig | 2 ++ configs/beelink-gtkingpro_defconfig | 2 ++ configs/blanche_defconfig | 2 ++ configs/brppt1_mmc_defconfig | 2 ++ configs/brppt1_nand_defconfig | 2 ++ configs/brppt1_spi_defconfig | 2 ++ configs/brsmarc1_defconfig | 2 ++ configs/brxre1_defconfig | 2 ++ configs/bubblegum_96_defconfig | 2 ++ configs/cgtqmx8_defconfig | 2 ++ configs/chiliboard_defconfig | 2 ++ configs/chromebit_mickey_defconfig | 2 ++ configs/chromebook_bob_defconfig | 2 ++ configs/chromebook_jerry_defconfig | 2 ++ configs/chromebook_kevin_defconfig | 2 ++ configs/chromebook_minnie_defconfig | 2 ++ configs/chromebook_speedy_defconfig | 2 ++ configs/clearfog_defconfig | 2 ++ configs/clearfog_gt_8k_defconfig | 2 ++ configs/cm_t335_defconfig | 2 ++ configs/cm_t43_defconfig | 2 ++ configs/colibri-imx8x_defconfig | 2 ++ configs/controlcenterdc_defconfig | 2 ++ configs/cortina_presidio-asic-base_defconfig | 2 ++ configs/cortina_presidio-asic-emmc_defconfig | 2 ++ configs/cortina_presidio-asic-pnand_defconfig | 2 ++ configs/corvus_defconfig | 2 ++ configs/crs305-1g-4s-bit_defconfig | 2 ++ configs/crs305-1g-4s_defconfig | 2 ++ configs/crs326-24g-2s-bit_defconfig | 2 ++ configs/crs326-24g-2s_defconfig | 2 ++ configs/crs328-4c-20s-4s-bit_defconfig | 2 ++ configs/crs328-4c-20s-4s_defconfig | 2 ++ configs/cubieboard7_defconfig | 2 ++ configs/d2net_v2_defconfig | 2 ++ configs/da850evm_defconfig | 2 ++ configs/da850evm_direct_nor_defconfig | 2 ++ configs/da850evm_nand_defconfig | 2 ++ configs/db-88f6720_defconfig | 2 ++ configs/db-88f6820-amc_defconfig | 2 ++ configs/db-88f6820-gp_defconfig | 2 ++ configs/db-mv784mp-gp_defconfig | 2 ++ configs/db-xc3-24g4xg_defconfig | 2 ++ configs/deneb_defconfig | 2 ++ configs/devkit3250_defconfig | 2 ++ configs/devkit8000_defconfig | 2 ++ configs/dns325_defconfig | 2 ++ configs/dockstar_defconfig | 2 ++ configs/dra7xx_evm_defconfig | 2 ++ configs/dra7xx_hs_evm_defconfig | 2 ++ configs/dra7xx_hs_evm_usb_defconfig | 2 ++ configs/draco_defconfig | 2 ++ configs/dragonboard410c_defconfig | 2 ++ configs/dragonboard820c_defconfig | 2 ++ configs/dreamplug_defconfig | 2 ++ configs/ds109_defconfig | 2 ++ configs/ds414_defconfig | 2 ++ configs/durian_defconfig | 2 ++ configs/ea-lpc3250devkitv2_defconfig | 2 ++ configs/edminiv2_defconfig | 2 ++ configs/elgin-rv1108_defconfig | 2 ++ configs/emsdp_defconfig | 2 ++ configs/espresso7420_defconfig | 2 ++ configs/etamin_defconfig | 2 ++ configs/evb-px30_defconfig | 2 ++ configs/evb-px5_defconfig | 2 ++ configs/evb-rk3036_defconfig | 2 ++ configs/evb-rk3128_defconfig | 2 ++ configs/evb-rk3229_defconfig | 2 ++ configs/evb-rk3288_defconfig | 2 ++ configs/evb-rk3308_defconfig | 2 ++ configs/evb-rk3328_defconfig | 2 ++ configs/evb-rk3399_defconfig | 2 ++ configs/evb-rk3568_defconfig | 2 ++ configs/evb-rv1108_defconfig | 2 ++ configs/ficus-rk3399_defconfig | 2 ++ configs/firefly-px30_defconfig | 2 ++ configs/firefly-rk3288_defconfig | 2 ++ configs/firefly-rk3399_defconfig | 2 ++ .../gardena-smart-gateway-at91sam_defconfig | 2 ++ configs/geekbox_defconfig | 2 ++ configs/giedi_defconfig | 2 ++ configs/goflexhome_defconfig | 2 ++ configs/gose_defconfig | 2 ++ configs/grpeach_defconfig | 2 ++ configs/guruplug_defconfig | 2 ++ configs/helios4_defconfig | 2 ++ configs/highbank_defconfig | 2 ++ configs/hikey960_defconfig | 2 ++ configs/hikey_defconfig | 2 ++ configs/hsdk_4xd_defconfig | 2 ++ configs/hsdk_defconfig | 2 ++ configs/ib62x0_defconfig | 2 ++ configs/iconnect_defconfig | 2 ++ configs/igep00x0_defconfig | 2 ++ configs/imgtec_xilfpga_defconfig | 2 ++ configs/imx8qm_mek_defconfig | 2 ++ configs/imx8qm_rom7720_a1_4G_defconfig | 2 ++ configs/imx8qxp_mek_defconfig | 2 ++ configs/imxrt1020-evk_defconfig | 2 ++ configs/imxrt1050-evk_defconfig | 2 ++ configs/inetspace_v2_defconfig | 2 ++ configs/integratorap_cm720t_defconfig | 2 ++ configs/integratorap_cm920t_defconfig | 2 ++ configs/integratorap_cm926ejs_defconfig | 2 ++ configs/integratorap_cm946es_defconfig | 2 ++ configs/integratorcp_cm1136_defconfig | 2 ++ configs/integratorcp_cm920t_defconfig | 2 ++ configs/integratorcp_cm926ejs_defconfig | 2 ++ configs/integratorcp_cm946es_defconfig | 2 ++ configs/iot2050_defconfig | 2 ++ configs/iot_devkit_defconfig | 2 ++ configs/j7200_evm_a72_defconfig | 2 ++ configs/j7200_evm_r5_defconfig | 2 ++ configs/j721e_evm_a72_defconfig | 2 ++ configs/j721e_evm_r5_defconfig | 2 ++ configs/j721e_hs_evm_a72_defconfig | 2 ++ configs/j721e_hs_evm_r5_defconfig | 2 ++ configs/j721s2_evm_a72_defconfig | 2 ++ configs/j721s2_evm_r5_defconfig | 2 ++ configs/jethub_j100_defconfig | 2 ++ configs/jethub_j80_defconfig | 2 ++ configs/k2e_evm_defconfig | 2 ++ configs/k2e_hs_evm_defconfig | 2 ++ configs/k2g_evm_defconfig | 2 ++ configs/k2g_hs_evm_defconfig | 2 ++ configs/k2hk_evm_defconfig | 2 ++ configs/k2hk_hs_evm_defconfig | 2 ++ configs/k2l_evm_defconfig | 2 ++ configs/k2l_hs_evm_defconfig | 2 ++ configs/khadas-edge-captain-rk3399_defconfig | 2 ++ configs/khadas-edge-rk3399_defconfig | 2 ++ configs/khadas-edge-v-rk3399_defconfig | 2 ++ configs/khadas-vim2_defconfig | 2 ++ configs/khadas-vim3_android_ab_defconfig | 2 ++ configs/khadas-vim3_android_defconfig | 2 ++ configs/khadas-vim3_defconfig | 2 ++ configs/khadas-vim3l_android_ab_defconfig | 2 ++ configs/khadas-vim3l_android_defconfig | 2 ++ configs/khadas-vim3l_defconfig | 2 ++ configs/khadas-vim_defconfig | 2 ++ configs/km_kirkwood_128m16_defconfig | 2 ++ configs/km_kirkwood_defconfig | 2 ++ configs/km_kirkwood_pci_defconfig | 2 ++ configs/kmcoge5un_defconfig | 2 ++ configs/kmnusa_defconfig | 2 ++ configs/kmsuse2_defconfig | 2 ++ configs/koelsch_defconfig | 2 ++ configs/kontron_sl28_defconfig | 2 ++ configs/kylin-rk3036_defconfig | 2 ++ configs/lager_defconfig | 2 ++ configs/leez-rk3399_defconfig | 2 ++ configs/legoev3_defconfig | 2 ++ configs/libretech-ac_defconfig | 2 ++ configs/libretech-cc_defconfig | 2 ++ configs/libretech-cc_v2_defconfig | 2 ++ configs/libretech-s905d-pc_defconfig | 2 ++ configs/libretech-s912-pc_defconfig | 2 ++ configs/lion-rk3368_defconfig | 2 ++ configs/ls1012a2g5rdb_qspi_defconfig | 2 ++ configs/ls1012afrdm_qspi_defconfig | 2 ++ configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1012afrwy_qspi_defconfig | 2 ++ configs/ls1012aqds_qspi_defconfig | 2 ++ configs/ls1012ardb_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1012ardb_qspi_defconfig | 2 ++ configs/ls1043aqds_defconfig | 2 ++ configs/ls1043aqds_lpuart_defconfig | 2 ++ configs/ls1043aqds_nand_defconfig | 2 ++ configs/ls1043aqds_nor_ddr3_defconfig | 2 ++ configs/ls1043aqds_qspi_defconfig | 2 ++ configs/ls1043aqds_sdcard_ifc_defconfig | 2 ++ configs/ls1043aqds_sdcard_qspi_defconfig | 2 ++ configs/ls1043ardb_SECURE_BOOT_defconfig | 2 ++ configs/ls1043ardb_defconfig | 2 ++ configs/ls1043ardb_nand_SECURE_BOOT_defconfig | 2 ++ configs/ls1043ardb_nand_defconfig | 2 ++ .../ls1043ardb_sdcard_SECURE_BOOT_defconfig | 2 ++ configs/ls1043ardb_sdcard_defconfig | 2 ++ configs/ls1046aqds_SECURE_BOOT_defconfig | 2 ++ configs/ls1046aqds_defconfig | 2 ++ configs/ls1046aqds_lpuart_defconfig | 2 ++ configs/ls1046aqds_nand_defconfig | 2 ++ configs/ls1046aqds_qspi_defconfig | 2 ++ configs/ls1046aqds_sdcard_ifc_defconfig | 2 ++ configs/ls1046aqds_sdcard_qspi_defconfig | 2 ++ configs/ls1046ardb_emmc_defconfig | 2 ++ configs/ls1046ardb_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1046ardb_qspi_defconfig | 2 ++ configs/ls1046ardb_qspi_spl_defconfig | 2 ++ .../ls1046ardb_sdcard_SECURE_BOOT_defconfig | 2 ++ configs/ls1046ardb_sdcard_defconfig | 2 ++ configs/ls1088aqds_defconfig | 2 ++ configs/ls1088aqds_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1088aqds_qspi_defconfig | 2 ++ configs/ls1088aqds_sdcard_ifc_defconfig | 2 ++ configs/ls1088aqds_sdcard_qspi_defconfig | 2 ++ configs/ls1088ardb_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1088ardb_qspi_defconfig | 2 ++ ...s1088ardb_sdcard_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls1088ardb_sdcard_qspi_defconfig | 2 ++ configs/ls2080aqds_SECURE_BOOT_defconfig | 2 ++ configs/ls2080aqds_defconfig | 2 ++ configs/ls2080aqds_nand_defconfig | 2 ++ configs/ls2080aqds_qspi_defconfig | 2 ++ configs/ls2080aqds_sdcard_defconfig | 2 ++ configs/ls2080ardb_SECURE_BOOT_defconfig | 2 ++ configs/ls2080ardb_defconfig | 2 ++ configs/ls2080ardb_nand_defconfig | 2 ++ configs/ls2081ardb_defconfig | 2 ++ configs/ls2088ardb_qspi_SECURE_BOOT_defconfig | 2 ++ configs/ls2088ardb_qspi_defconfig | 2 ++ configs/lschlv2_defconfig | 2 ++ configs/lsxhl_defconfig | 2 ++ configs/maxbcm_defconfig | 2 ++ configs/microchip_mpfs_icicle_defconfig | 2 ++ configs/miqi-rk3288_defconfig | 2 ++ configs/mk808_defconfig | 2 ++ configs/mt7623a_unielec_u7623_02_defconfig | 2 ++ configs/mt7623n_bpir2_defconfig | 2 ++ configs/mt7629_rfb_defconfig | 2 ++ configs/mvebu_crb_cn9130_defconfig | 2 ++ configs/mvebu_db-88f3720_defconfig | 2 ++ configs/mvebu_db_armada8k_defconfig | 2 ++ configs/mvebu_db_cn9130_defconfig | 2 ++ configs/mvebu_espressobin-88f3720_defconfig | 2 ++ configs/mvebu_mcbin-88f8040_defconfig | 2 ++ configs/mvebu_puzzle-m801-88f8040_defconfig | 2 ++ configs/nanopc-t4-rk3399_defconfig | 2 ++ configs/nanopi-k2_defconfig | 2 ++ configs/nanopi-m4-2gb-rk3399_defconfig | 2 ++ configs/nanopi-m4-rk3399_defconfig | 2 ++ configs/nanopi-m4b-rk3399_defconfig | 2 ++ configs/nanopi-neo4-rk3399_defconfig | 2 ++ configs/nanopi-r2s-rk3328_defconfig | 2 ++ configs/nanopi-r4s-rk3399_defconfig | 2 ++ configs/nas220_defconfig | 2 ++ configs/net2big_v2_defconfig | 2 ++ configs/netspace_lite_v2_defconfig | 2 ++ configs/netspace_max_v2_defconfig | 2 ++ configs/netspace_mini_v2_defconfig | 2 ++ configs/netspace_v2_defconfig | 2 ++ configs/nsa310s_defconfig | 2 ++ configs/nsim_700_defconfig | 2 ++ configs/nsim_700be_defconfig | 2 ++ configs/nsim_hs38_defconfig | 2 ++ configs/nsim_hs38be_defconfig | 2 ++ configs/octeontx2_95xx_defconfig | 2 ++ configs/octeontx2_96xx_defconfig | 2 ++ configs/octeontx_81xx_defconfig | 2 ++ configs/octeontx_83xx_defconfig | 2 ++ configs/odroid-c2_defconfig | 2 ++ configs/odroid-c4_defconfig | 2 ++ configs/odroid-go2_defconfig | 2 ++ configs/odroid-hc4_defconfig | 2 ++ configs/odroid-n2_defconfig | 2 ++ configs/odroid-xu3_defconfig | 2 ++ configs/odroid_defconfig | 2 ++ configs/omap35_logic_defconfig | 2 ++ configs/omap35_logic_somlv_defconfig | 2 ++ configs/omap3_beagle_defconfig | 2 ++ configs/omap3_evm_defconfig | 2 ++ configs/omap3_logic_defconfig | 2 ++ configs/omap3_logic_somlv_defconfig | 2 ++ configs/omap4_panda_defconfig | 2 ++ configs/omap4_sdp4430_defconfig | 2 ++ configs/omap5_uevm_defconfig | 2 ++ configs/omapl138_lcdk_defconfig | 2 ++ configs/openpiton_riscv64_defconfig | 2 ++ configs/openpiton_riscv64_spl_defconfig | 2 ++ configs/openrd_base_defconfig | 2 ++ configs/openrd_client_defconfig | 2 ++ configs/openrd_ultimate_defconfig | 2 ++ configs/orangepi-rk3399_defconfig | 2 ++ configs/origen_defconfig | 2 ++ configs/p200_defconfig | 2 ++ configs/p201_defconfig | 2 ++ configs/p212_defconfig | 2 ++ configs/peach-pi_defconfig | 2 ++ configs/peach-pit_defconfig | 2 ++ configs/phycore-am335x-r2-regor_defconfig | 2 ++ configs/phycore-am335x-r2-wega_defconfig | 2 ++ configs/phycore-rk3288_defconfig | 2 ++ configs/pic32mzdask_defconfig | 2 ++ configs/pinebook-pro-rk3399_defconfig | 2 ++ configs/pm9261_defconfig | 2 ++ configs/pm9263_defconfig | 2 ++ configs/pm9g45_defconfig | 2 ++ configs/pogo_e02_defconfig | 2 ++ configs/pogo_v4_defconfig | 2 ++ configs/poleg_evb_defconfig | 2 ++ configs/pomelo_defconfig | 2 ++ configs/poplar_defconfig | 2 ++ configs/popmetal-rk3288_defconfig | 2 ++ configs/porter_defconfig | 2 ++ configs/puma-rk3399_defconfig | 2 ++ configs/px30-core-ctouch2-of10-px30_defconfig | 2 ++ configs/px30-core-ctouch2-px30_defconfig | 2 ++ configs/px30-core-edimm2.2-px30_defconfig | 2 ++ configs/pxm2_defconfig | 2 ++ configs/qemu-riscv32_defconfig | 2 ++ configs/qemu-riscv32_smode_defconfig | 2 ++ configs/qemu-riscv32_spl_defconfig | 2 ++ configs/qemu-riscv64_defconfig | 2 ++ configs/qemu-riscv64_smode_defconfig | 2 ++ configs/qemu-riscv64_spl_defconfig | 2 ++ configs/qemu_arm64_defconfig | 2 ++ configs/qemu_arm_defconfig | 2 ++ configs/radxa-zero_defconfig | 2 ++ configs/rastaban_defconfig | 2 ++ configs/roc-cc-rk3308_defconfig | 2 ++ configs/roc-cc-rk3328_defconfig | 2 ++ configs/roc-pc-mezzanine-rk3399_defconfig | 2 ++ configs/roc-pc-rk3399_defconfig | 2 ++ configs/rock-pi-4-rk3399_defconfig | 2 ++ configs/rock-pi-4c-rk3399_defconfig | 2 ++ configs/rock-pi-e-rk3328_defconfig | 2 ++ configs/rock-pi-n10-rk3399pro_defconfig | 2 ++ configs/rock-pi-n8-rk3288_defconfig | 2 ++ configs/rock2_defconfig | 2 ++ configs/rock64-rk3328_defconfig | 2 ++ configs/rock960-rk3399_defconfig | 2 ++ configs/rock_defconfig | 2 ++ configs/rockpro64-rk3399_defconfig | 2 ++ configs/rpi_0_w_defconfig | 2 ++ configs/rpi_2_defconfig | 2 ++ configs/rpi_3_32b_defconfig | 2 ++ configs/rpi_3_b_plus_defconfig | 2 ++ configs/rpi_3_defconfig | 2 ++ configs/rpi_4_32b_defconfig | 2 ++ configs/rpi_4_defconfig | 2 ++ configs/rpi_arm64_defconfig | 2 ++ configs/rpi_defconfig | 2 ++ configs/rut_defconfig | 2 ++ configs/s400_defconfig | 2 ++ configs/s5p4418_nanopi2_defconfig | 2 ++ configs/s5p_goni_defconfig | 2 ++ configs/s5pc210_universal_defconfig | 2 ++ configs/sam9x60_curiosity_mmc_defconfig | 2 ++ configs/sam9x60ek_mmc_defconfig | 2 ++ configs/sam9x60ek_nandflash_defconfig | 2 ++ configs/sam9x60ek_qspiflash_defconfig | 2 ++ configs/sama5d27_giantboard_defconfig | 2 ++ configs/sama5d27_som1_ek_mmc1_defconfig | 2 ++ configs/sama5d27_som1_ek_mmc_defconfig | 2 ++ configs/sama5d27_som1_ek_qspiflash_defconfig | 2 ++ configs/sama5d27_wlsom1_ek_mmc_defconfig | 2 ++ configs/sama5d27_wlsom1_ek_qspiflash_defconfig | 2 ++ configs/sama5d2_icp_mmc_defconfig | 2 ++ configs/sama5d2_icp_qspiflash_defconfig | 2 ++ configs/sama5d2_ptc_ek_mmc_defconfig | 2 ++ configs/sama5d2_ptc_ek_nandflash_defconfig | 2 ++ configs/sama5d2_xplained_emmc_defconfig | 2 ++ configs/sama5d2_xplained_mmc_defconfig | 2 ++ configs/sama5d2_xplained_qspiflash_defconfig | 2 ++ configs/sama5d2_xplained_spiflash_defconfig | 2 ++ configs/sama5d36ek_cmp_mmc_defconfig | 2 ++ configs/sama5d36ek_cmp_nandflash_defconfig | 2 ++ configs/sama5d36ek_cmp_spiflash_defconfig | 2 ++ configs/sama5d3_xplained_mmc_defconfig | 2 ++ configs/sama5d3_xplained_nandflash_defconfig | 2 ++ configs/sama5d3xek_mmc_defconfig | 2 ++ configs/sama5d3xek_nandflash_defconfig | 2 ++ configs/sama5d3xek_spiflash_defconfig | 2 ++ configs/sama5d4_xplained_mmc_defconfig | 2 ++ configs/sama5d4_xplained_nandflash_defconfig | 2 ++ configs/sama5d4_xplained_spiflash_defconfig | 2 ++ configs/sama5d4ek_mmc_defconfig | 2 ++ configs/sama5d4ek_nandflash_defconfig | 2 ++ configs/sama5d4ek_spiflash_defconfig | 2 ++ configs/sama7g5ek_mmc1_defconfig | 2 ++ configs/sama7g5ek_mmc_defconfig | 2 ++ configs/sei510_defconfig | 2 ++ configs/sei610_defconfig | 2 ++ configs/sheep-rk3368_defconfig | 2 ++ configs/sheevaplug_defconfig | 2 ++ configs/sifive_unleashed_defconfig | 2 ++ configs/sifive_unmatched_defconfig | 2 ++ configs/silk_defconfig | 2 ++ configs/sipeed_maix_bitm_defconfig | 2 ++ configs/sipeed_maix_smode_defconfig | 2 ++ configs/smdk5250_defconfig | 2 ++ configs/smdk5420_defconfig | 2 ++ configs/smdkc100_defconfig | 2 ++ configs/smdkv310_defconfig | 2 ++ configs/sniper_defconfig | 2 ++ configs/snow_defconfig | 2 ++ configs/socfpga_agilex_atf_defconfig | 2 ++ configs/socfpga_agilex_defconfig | 2 ++ configs/socfpga_agilex_vab_defconfig | 2 ++ configs/socfpga_arria10_defconfig | 2 ++ configs/socfpga_arria5_defconfig | 2 ++ configs/socfpga_cyclone5_defconfig | 2 ++ configs/socfpga_dbm_soc1_defconfig | 2 ++ configs/socfpga_de0_nano_soc_defconfig | 2 ++ configs/socfpga_de10_nano_defconfig | 2 ++ configs/socfpga_de1_soc_defconfig | 2 ++ configs/socfpga_is1_defconfig | 2 ++ configs/socfpga_mcvevk_defconfig | 2 ++ configs/socfpga_n5x_atf_defconfig | 2 ++ configs/socfpga_n5x_defconfig | 2 ++ configs/socfpga_n5x_vab_defconfig | 2 ++ configs/socfpga_secu1_defconfig | 2 ++ configs/socfpga_sockit_defconfig | 2 ++ configs/socfpga_socrates_defconfig | 2 ++ configs/socfpga_sr1500_defconfig | 2 ++ configs/socfpga_stratix10_atf_defconfig | 2 ++ configs/socfpga_stratix10_defconfig | 2 ++ configs/socfpga_vining_fpga_defconfig | 2 ++ configs/spring_defconfig | 2 ++ configs/stemmy_defconfig | 2 ++ configs/stih410-b2260_defconfig | 2 ++ configs/stm32746g-eval_defconfig | 2 ++ configs/stm32746g-eval_spl_defconfig | 2 ++ configs/stm32f429-discovery_defconfig | 2 ++ configs/stm32f429-evaluation_defconfig | 2 ++ configs/stm32f469-discovery_defconfig | 2 ++ configs/stm32f746-disco_defconfig | 2 ++ configs/stm32f746-disco_spl_defconfig | 2 ++ configs/stm32f769-disco_defconfig | 2 ++ configs/stm32f769-disco_spl_defconfig | 2 ++ configs/stm32h743-disco_defconfig | 2 ++ configs/stm32h743-eval_defconfig | 2 ++ configs/stm32h750-art-pi_defconfig | 2 ++ .../stm32mp15-icore-stm32mp1-ctouch2_defconfig | 2 ++ ...stm32mp15-icore-stm32mp1-edimm2.2_defconfig | 2 ++ ...5-microgea-stm32mp1-microdev2-of7_defconfig | 2 ++ ...2mp15-microgea-stm32mp1-microdev2_defconfig | 2 ++ configs/stm32mp15_basic_defconfig | 2 ++ configs/stm32mp15_defconfig | 1 + configs/stm32mp15_dhcom_basic_defconfig | 2 ++ configs/stm32mp15_dhcor_basic_defconfig | 2 ++ configs/stm32mp15_trusted_defconfig | 1 + configs/stout_defconfig | 2 ++ configs/synquacer_developerbox_defconfig | 2 ++ configs/tb100_defconfig | 2 ++ configs/theadorable_debug_defconfig | 2 ++ configs/thuban_defconfig | 2 ++ configs/thunderx_88xx_defconfig | 2 ++ configs/ti816x_evm_defconfig | 2 ++ configs/tinker-rk3288_defconfig | 2 ++ configs/tinker-s-rk3288_defconfig | 2 ++ configs/total_compute_defconfig | 2 ++ configs/tplink_wdr4300_defconfig | 2 ++ configs/trats2_defconfig | 2 ++ configs/trats_defconfig | 2 ++ configs/turris_mox_defconfig | 2 ++ configs/turris_omnia_defconfig | 2 ++ configs/u200_defconfig | 2 ++ configs/uDPU_defconfig | 2 ++ configs/uniphier_ld4_sld8_defconfig | 2 ++ configs/uniphier_v7_defconfig | 2 ++ configs/vexpress_aemv8a_juno_defconfig | 2 ++ configs/vexpress_ca9x4_defconfig | 2 ++ configs/vinco_defconfig | 2 ++ configs/vyasa-rk3288_defconfig | 2 ++ configs/wetek-core2_defconfig | 2 ++ configs/work_92105_defconfig | 2 ++ configs/x530_defconfig | 2 ++ configs/xilinx_versal_mini_defconfig | 2 ++ configs/xilinx_versal_mini_emmc0_defconfig | 2 ++ configs/xilinx_versal_mini_emmc1_defconfig | 2 ++ configs/xilinx_zynqmp_mini_defconfig | 2 ++ configs/xilinx_zynqmp_mini_emmc0_defconfig | 2 ++ configs/xilinx_zynqmp_mini_emmc1_defconfig | 2 ++ configs/xilinx_zynqmp_mini_nand_defconfig | 2 ++ .../xilinx_zynqmp_mini_nand_single_defconfig | 2 ++ configs/xilinx_zynqmp_mini_qspi_defconfig | 2 ++ include/configs/M5208EVBE.h | 1 - include/configs/M5235EVB.h | 1 - include/configs/M5249EVB.h | 1 - include/configs/M5253DEMO.h | 1 - include/configs/M5272C3.h | 1 - include/configs/M5275EVB.h | 1 - include/configs/M5282EVB.h | 1 - include/configs/M53017EVB.h | 1 - include/configs/M5329EVB.h | 1 - include/configs/M5373EVB.h | 1 - include/configs/MPC837XERDB.h | 2 -- include/configs/MPC8548CDS.h | 1 - include/configs/P1010RDB.h | 1 - include/configs/P2041RDB.h | 1 - include/configs/T102xRDB.h | 1 - include/configs/T104xRDB.h | 1 - include/configs/T208xQDS.h | 1 - include/configs/T208xRDB.h | 1 - include/configs/T4240RDB.h | 1 - include/configs/alt.h | 3 +-- include/configs/am64x_evm.h | 2 -- include/configs/am65x_evm.h | 2 -- include/configs/amcore.h | 2 -- include/configs/ap121.h | 2 -- include/configs/ap143.h | 2 -- include/configs/ap152.h | 2 -- include/configs/apalis-imx8.h | 2 -- include/configs/apalis_imx6.h | 5 ----- include/configs/aristainetos2.h | 5 ----- include/configs/armadillo-800eva.h | 3 +-- include/configs/arndale.h | 3 --- include/configs/aspeed-common.h | 5 ----- include/configs/astro_mcf5373l.h | 2 -- include/configs/at91sam9260ek.h | 12 +++--------- include/configs/at91sam9261ek.h | 4 ++-- include/configs/at91sam9263ek.h | 4 ++-- include/configs/at91sam9m10g45ek.h | 3 --- include/configs/at91sam9n12ek.h | 8 -------- include/configs/at91sam9rlek.h | 4 ++-- include/configs/at91sam9x5ek.h | 3 --- include/configs/ax25-ae350.h | 2 -- include/configs/axs10x.h | 3 --- include/configs/bcm_ns3.h | 1 - include/configs/bcmstb.h | 3 --- include/configs/bk4r1.h | 5 ----- include/configs/blanche.h | 3 +-- include/configs/broadcom_bcm963158.h | 1 - include/configs/broadcom_bcm96753ref.h | 1 - include/configs/broadcom_bcm968360bg.h | 1 - include/configs/broadcom_bcm968580xref.h | 1 - include/configs/brppt2.h | 4 ---- include/configs/bur_am335x_common.h | 2 -- include/configs/capricorn-common.h | 1 - include/configs/cgtqmx8.h | 2 -- include/configs/cl-som-imx7.h | 5 ----- include/configs/cm_fx6.h | 4 ---- include/configs/cobra5272.h | 1 - include/configs/colibri-imx6ull.h | 5 ----- include/configs/colibri-imx8x.h | 2 -- include/configs/colibri_imx6.h | 5 ----- include/configs/colibri_imx7.h | 5 ----- include/configs/colibri_vf.h | 5 ----- include/configs/corenet_ds.h | 1 - include/configs/corvus.h | 3 --- include/configs/da850evm.h | 7 ------- include/configs/dart_6ul.h | 5 ----- include/configs/devkit3250.h | 3 --- include/configs/dh_imx6.h | 6 ------ include/configs/display5.h | 5 ----- include/configs/dragonboard410c.h | 1 - include/configs/dragonboard820c.h | 1 - include/configs/durian.h | 2 -- include/configs/ea-lpc3250devkitv2.h | 1 - include/configs/eb_cpu5282.h | 2 -- include/configs/edminiv2.h | 2 -- include/configs/el6x_common.h | 5 ----- include/configs/embestmx6boards.h | 5 ----- include/configs/emsdp.h | 2 -- include/configs/espresso7420.h | 1 - include/configs/ethernut5.h | 6 ++---- include/configs/exynos5250-common.h | 4 ---- include/configs/exynos78x0-common.h | 1 - .../configs/gardena-smart-gateway-at91sam.h | 3 --- include/configs/gazerbeam.h | 2 -- include/configs/ge_b1x5v2.h | 5 ----- include/configs/ge_bx50v3.h | 5 ----- include/configs/gose.h | 3 +-- include/configs/grpeach.h | 2 -- include/configs/gw_ventana.h | 5 ----- include/configs/highbank.h | 1 - include/configs/hikey.h | 2 -- include/configs/hikey960.h | 2 -- include/configs/hsdk-4xd.h | 3 --- include/configs/hsdk.h | 3 --- include/configs/ids8313.h | 2 -- include/configs/imgtec_xilfpga.h | 2 -- include/configs/imx27lite-common.h | 2 -- include/configs/imx6-engicam.h | 5 ----- include/configs/imx6_logic.h | 5 ----- include/configs/imx6dl-mamoj.h | 5 ----- include/configs/imx6q-bosch-acc.h | 3 --- include/configs/imx7-cm.h | 5 ----- include/configs/imx8mm-cl-iot-gate.h | 4 ---- include/configs/imx8mm_beacon.h | 4 ---- include/configs/imx8mm_data_modul_edm_sbc.h | 4 ---- include/configs/imx8mm_evk.h | 4 ---- include/configs/imx8mm_icore_mx8mm.h | 4 ---- include/configs/imx8mm_venice.h | 4 ---- include/configs/imx8mn_beacon.h | 4 ---- include/configs/imx8mn_bsh_smm_s2_common.h | 4 ---- include/configs/imx8mn_evk.h | 4 ---- include/configs/imx8mn_var_som.h | 4 ---- include/configs/imx8mn_venice.h | 4 ---- include/configs/imx8mp_dhcom_pdk2.h | 4 ---- include/configs/imx8mp_evk.h | 4 ---- include/configs/imx8mp_rsb3720.h | 4 ---- include/configs/imx8mp_venice.h | 4 ---- include/configs/imx8mq_cm.h | 4 ---- include/configs/imx8mq_evk.h | 4 ---- include/configs/imx8mq_phanbell.h | 4 ---- include/configs/imx8qm_mek.h | 2 -- include/configs/imx8qm_rom7720.h | 2 -- include/configs/imx8qxp_mek.h | 2 -- include/configs/imx8ulp_evk.h | 2 -- include/configs/imxrt1020-evk.h | 2 -- include/configs/imxrt1050-evk.h | 2 -- include/configs/integrator-common.h | 4 ---- include/configs/iot2050.h | 2 -- include/configs/iot_devkit.h | 10 ++++------ include/configs/j721e_evm.h | 2 -- include/configs/j721s2_evm.h | 2 -- include/configs/km/km-mpc83xx.h | 2 -- include/configs/km/pg-wcom-ls102xa.h | 5 ----- include/configs/kmcent2.h | 1 - include/configs/koelsch.h | 3 +-- include/configs/kontron-sl-mx6ul.h | 5 ----- include/configs/kontron-sl-mx8mm.h | 5 ----- include/configs/kontron_pitx_imx8m.h | 4 ---- include/configs/kontron_sl28.h | 1 - include/configs/kp_imx53.h | 5 ----- include/configs/kp_imx6q_tpc.h | 6 ------ include/configs/kzm9g.h | 3 --- include/configs/lager.h | 3 +-- include/configs/legoev3.h | 2 -- include/configs/liteboard.h | 5 ----- include/configs/ls1012a_common.h | 6 ------ include/configs/ls1021aiot.h | 5 ----- include/configs/ls1021aqds.h | 5 ----- include/configs/ls1021atsn.h | 5 ----- include/configs/ls1021atwr.h | 5 ----- include/configs/ls1028a_common.h | 1 - include/configs/ls1043a_common.h | 5 ----- include/configs/ls1043aqds.h | 3 --- include/configs/ls1046a_common.h | 5 ----- include/configs/ls1046aqds.h | 3 --- include/configs/ls1088a_common.h | 5 ----- include/configs/ls2080a_common.h | 5 ----- include/configs/lx2160a_common.h | 1 - include/configs/m53menlo.h | 5 ----- include/configs/mccmon6.h | 5 ----- include/configs/meerkat96.h | 5 ----- include/configs/meesc.h | 9 ++------- include/configs/meson64.h | 1 - include/configs/microchip_mpfs_icicle.h | 1 - include/configs/mt7622.h | 2 -- include/configs/mt7623.h | 2 -- include/configs/mt7629.h | 2 -- include/configs/mt8183.h | 3 --- include/configs/mt8512.h | 3 --- include/configs/mt8516.h | 3 --- include/configs/mt8518.h | 3 --- include/configs/mvebu_armada-37xx.h | 3 --- include/configs/mvebu_armada-8k.h | 3 --- include/configs/mx51evk.h | 5 ----- include/configs/mx53cx9020.h | 5 ----- include/configs/mx53loco.h | 5 ----- include/configs/mx53ppd.h | 5 ----- include/configs/mx6cuboxi.h | 5 ----- include/configs/mx6memcal.h | 5 ----- include/configs/mx6sabre_common.h | 5 ----- include/configs/mx6slevk.h | 5 ----- include/configs/mx6sllevk.h | 5 ----- include/configs/mx6sxsabreauto.h | 5 ----- include/configs/mx6sxsabresd.h | 5 ----- include/configs/mx6ul_14x14_evk.h | 5 ----- include/configs/mx6ullevk.h | 5 ----- include/configs/mx7dsabresd.h | 5 ----- include/configs/mx7ulp_com.h | 5 ----- include/configs/mx7ulp_evk.h | 5 ----- include/configs/mxs.h | 4 ---- include/configs/mys_6ulx.h | 5 ----- include/configs/nitrogen6x.h | 5 ----- include/configs/nokia_rx51.h | 2 -- include/configs/novena.h | 5 ----- include/configs/npi_imx6ull.h | 5 ----- include/configs/nsim.h | 3 --- include/configs/o4-imx6ull-nano.h | 2 -- include/configs/octeontx2_common.h | 1 - include/configs/octeontx_common.h | 1 - include/configs/odroid.h | 3 --- include/configs/odroid_xu3.h | 2 -- include/configs/omapl138_lcdk.h | 2 -- include/configs/openpiton-riscv64.h | 1 - include/configs/opos6uldev.h | 4 ---- include/configs/origen.h | 2 -- include/configs/owl-common.h | 1 - include/configs/p1_p2_rdb_pc.h | 1 - include/configs/pcl063.h | 5 ----- include/configs/pcl063_ull.h | 5 ----- include/configs/pcm052.h | 5 ----- include/configs/pcm058.h | 5 ----- include/configs/peach-pi.h | 1 - include/configs/peach-pit.h | 1 - include/configs/phycore_imx8mm.h | 4 ---- include/configs/phycore_imx8mp.h | 4 ---- include/configs/pic32mzdask.h | 2 -- include/configs/pico-imx6.h | 5 ----- include/configs/pico-imx6ul.h | 5 ----- include/configs/pico-imx7d.h | 5 ----- include/configs/pico-imx8mq.h | 4 ---- include/configs/pm9261.h | 2 -- include/configs/pm9263.h | 2 -- include/configs/pm9g45.h | 3 --- include/configs/poleg.h | 1 - include/configs/pomelo.h | 1 - include/configs/poplar.h | 1 - include/configs/porter.h | 3 +-- include/configs/presidio_asic.h | 1 - include/configs/px30_common.h | 1 - include/configs/qemu-arm.h | 3 --- include/configs/qemu-ppce500.h | 1 - include/configs/qemu-riscv.h | 1 - include/configs/rcar-gen3-common.h | 1 - include/configs/rk3036_common.h | 1 - include/configs/rk3066_common.h | 2 -- include/configs/rk3128_common.h | 2 -- include/configs/rk3188_common.h | 5 ----- include/configs/rk322x_common.h | 2 -- include/configs/rk3288_common.h | 4 ---- include/configs/rk3308_common.h | 1 - include/configs/rk3328_common.h | 1 - include/configs/rk3368_common.h | 2 -- include/configs/rk3399_common.h | 2 -- include/configs/rk3568_common.h | 2 -- include/configs/rpi.h | 3 --- include/configs/rv1108_common.h | 1 - include/configs/s5p4418_nanopi2.h | 1 - include/configs/s5p_goni.h | 2 -- include/configs/s5pc210_universal.h | 3 --- include/configs/sam9x60_curiosity.h | 3 --- include/configs/sam9x60ek.h | 4 ---- include/configs/sama5d27_som1_ek.h | 3 --- include/configs/sama5d27_wlsom1_ek.h | 3 --- include/configs/sama5d2_icp.h | 2 -- include/configs/sama5d2_ptc_ek.h | 3 --- include/configs/sama5d2_xplained.h | 3 --- include/configs/sama5d3_xplained.h | 2 -- include/configs/sama5d3xek.h | 2 -- include/configs/sama5d4_xplained.h | 2 -- include/configs/sama5d4ek.h | 2 -- include/configs/sama7g5ek.h | 3 --- include/configs/siemens-am33x-common.h | 2 -- include/configs/sifive-unleashed.h | 1 - include/configs/sifive-unmatched.h | 1 - include/configs/silk.h | 3 +-- include/configs/sipeed-maix.h | 3 --- include/configs/smartweb.h | 4 ++-- include/configs/smdk5420.h | 1 - include/configs/smdkc100.h | 2 -- include/configs/smdkv310.h | 2 -- include/configs/smegw01.h | 5 ----- include/configs/snapper9260.h | 4 ++-- include/configs/snapper9g45.h | 4 ++-- include/configs/sniper.h | 2 -- include/configs/socfpga_common.h | 5 ----- include/configs/socfpga_soc64_common.h | 3 --- include/configs/socrates.h | 1 - include/configs/somlabs_visionsom_6ull.h | 5 ----- include/configs/stemmy.h | 1 - include/configs/stih410-b2260.h | 4 ---- include/configs/stm32f429-discovery.h | 2 -- include/configs/stm32f429-evaluation.h | 2 -- include/configs/stm32f469-discovery.h | 2 -- include/configs/stm32f746-disco.h | 1 - include/configs/stm32h743-disco.h | 1 - include/configs/stm32h743-eval.h | 1 - include/configs/stm32h750-art-pi.h | 1 - include/configs/stm32mp15_common.h | 1 - include/configs/stout.h | 3 +-- include/configs/stv0991.h | 4 ---- include/configs/sunxi-common.h | 5 ----- include/configs/synquacer.h | 1 - include/configs/taurus.h | 4 ++-- include/configs/tb100.h | 3 --- include/configs/tbs2910.h | 4 ---- include/configs/tegra-common.h | 5 ----- include/configs/thunderx_88xx.h | 1 - include/configs/ti814x_evm.h | 2 -- include/configs/ti_armv7_common.h | 5 ----- include/configs/ti_armv7_keystone2.h | 2 -- include/configs/total_compute.h | 1 - include/configs/tplink_wdr4300.h | 2 -- include/configs/tqma6.h | 5 ----- include/configs/trats.h | 3 --- include/configs/trats2.h | 3 --- include/configs/turris_mox.h | 1 - include/configs/udoo.h | 5 ----- include/configs/udoo_neo.h | 5 ----- include/configs/uniphier.h | 2 -- include/configs/usb_a9263.h | 4 ++-- include/configs/usbarmory.h | 5 ----- include/configs/verdin-imx8mm.h | 4 ---- include/configs/verdin-imx8mp.h | 4 ---- include/configs/vexpress_aemv8.h | 2 -- include/configs/vexpress_common.h | 3 --- include/configs/vf610twr.h | 5 ----- include/configs/vinco.h | 3 --- include/configs/vining_2000.h | 5 ----- include/configs/wandboard.h | 5 ----- include/configs/warp.h | 5 ----- include/configs/warp7.h | 5 ----- include/configs/work_92105.h | 3 --- include/configs/xilinx_versal.h | 2 -- include/configs/xilinx_versal_mini_qspi.h | 3 --- include/configs/xilinx_zynqmp.h | 2 -- include/configs/xilinx_zynqmp_mini.h | 1 - include/configs/xilinx_zynqmp_mini_emmc.h | 2 -- include/configs/xilinx_zynqmp_mini_nand.h | 1 - include/configs/xilinx_zynqmp_mini_qspi.h | 2 -- include/configs/xilinx_zynqmp_r5.h | 3 --- include/configs/xpress.h | 5 ----- include/configs/zynq-common.h | 3 --- include/system-constants.h | 16 ++++++++++++++++ 894 files changed, 1183 insertions(+), 1027 deletions(-)
Kconfig +18 -0
@@ -242,6 +242,24 @@ config SYS_BOOT_GET_KBD Enables allocating and saving a kernel copy of the bd_info in space between "bootm_low" and "bootm_low" + BOOTMAPSZ. +config HAS_CUSTOM_SYS_INIT_SP_ADDR + bool "Use a custom location for the initial stack pointer address" + depends on ARC || (ARM && !INIT_SP_RELATIVE) || MIPS || PPC || RISCV + default y if TFABOOT + help + Typically, we use an initial stack pointer address that is calculated + by taking the statically defined CONFIG_SYS_INIT_RAM_ADDR, adding the + statically defined CONFIG_SYS_INIT_RAM_SIZE and then subtracting the + build-time constant of GENERATED_GBL_DATA_SIZE. On MIPS a different + but statica calculation is performed. However, some platforms will + take a different approach. Say Y here to define the address statically + instead. + +config CUSTOM_SYS_INIT_SP_ADDR + hex "Static location for the initial stack pointer" + depends on HAS_CUSTOM_SYS_INIT_SP_ADDR + default SYS_TEXT_BASE if TFABOOT + config SYS_MALLOC_F bool "Enable malloc() pool before relocation" default y if DM
README +0 -6
@@ -493,12 +493,6 @@ The following options need to be configured: Defines the SEC controller register space as Little Endian - MIPS CPU options: - CONFIG_SYS_INIT_SP_OFFSET - - Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack - pointer. This is needed for the temporary stack before - relocation. - CONFIG_XWAY_SWAP_BYTES Enable compilation of tools/xway-swap-bytes needed for Lantiq
arch/arc/lib/start.S +2 -1
@@ -7,6 +7,7 @@ #include <config.h> #include <linux/linkage.h> #include <asm/arcregs.h> +#include <system-constants.h> ENTRY(_start) /* Setup interrupt vector base that matches "__text_start" */
@@ -86,7 +87,7 @@ ENTRY(_start) #endif /* Establish C runtime stack and frame */ - mov %sp, CONFIG_SYS_INIT_SP_ADDR + mov %sp, SYS_INIT_SP_ADDR mov %fp, %sp /* Allocate reserved area from current top of stack */
arch/arm/cpu/arm926ejs/mxs/start.S +2 -1
@@ -21,6 +21,7 @@ #include <asm-offsets.h> #include <config.h> #include <common.h> +#include <system-constants.h> /* *************************************************************************
@@ -44,7 +45,7 @@ reset: * it point to the end of OCRAM if the SP is zero. */ cmp sp, #0x00000000 - ldreq sp, =CONFIG_SYS_INIT_SP_ADDR + ldreq sp, =SYS_INIT_SP_ADDR /* * Store all registers on old stack pointer, this will allow us later to
arch/arm/cpu/armv7/lowlevel_init.S +2 -1
@@ -13,6 +13,7 @@ #include <asm-offsets.h> #include <config.h> #include <linux/linkage.h> +#include <system-constants.h> .pushsection .text.s_init, "ax" WEAK(s_init)
@@ -28,7 +29,7 @@ WEAK(lowlevel_init) #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK) ldr sp, =CONFIG_SPL_STACK #else - ldr sp, =CONFIG_SYS_INIT_SP_ADDR + ldr sp, =SYS_INIT_SP_ADDR #endif bic sp, sp, #7 /* 8-byte alignment for ABI compliance */ #ifdef CONFIG_SPL_DM
arch/arm/cpu/armv7/start.S +2 -1
@@ -17,6 +17,7 @@ #include <asm/system.h> #include <linux/linkage.h> #include <asm/armv7.h> +#include <system-constants.h> /************************************************************************* *
@@ -254,7 +255,7 @@ ENTRY(cpu_init_cp15) #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK) ldr r0, =(CONFIG_SPL_STACK) #else - ldr r0, =(CONFIG_SYS_INIT_SP_ADDR) + ldr r0, =(SYS_INIT_SP_ADDR) #endif bic r0, r0, #7 /* 8-byte alignment for ABI compliance */ mov sp, r0
arch/arm/lib/crt0.S +2 -1
@@ -9,6 +9,7 @@ #include <asm-offsets.h> #include <linux/linkage.h> #include <asm/assembler.h> +#include <system-constants.h> /* * This file handles the target-independent stages of the U-Boot
@@ -104,7 +105,7 @@ ENTRY(_main) #elif defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK) ldr r0, =(CONFIG_SPL_STACK) #else - ldr r0, =(CONFIG_SYS_INIT_SP_ADDR) + ldr r0, =(SYS_INIT_SP_ADDR) #endif bic r0, r0, #7 /* 8-byte alignment for ABI compliance */ mov sp, r0
arch/arm/lib/crt0_64.S +2 -1
@@ -13,6 +13,7 @@ #include <asm-offsets.h> #include <asm/macro.h> #include <linux/linkage.h> +#include <system-constants.h> /* * This file handles the target-independent stages of the U-Boot
@@ -81,7 +82,7 @@ ENTRY(_main) #endif add x0, x0, #CONFIG_SYS_INIT_SP_BSS_OFFSET #else - ldr x0, =(CONFIG_SYS_INIT_SP_ADDR) + ldr x0, =(SYS_INIT_SP_ADDR) #endif bic sp, x0, #0xf /* 16-byte alignment for ABI compliance */ mov x0, sp
arch/arm/lib/vectors_m.S +2 -1
@@ -7,6 +7,7 @@ #include <config.h> #include <asm/assembler.h> #include <linux/linkage.h> +#include <system-constants.h> .type __hard_fault_entry, %function __hard_fault_entry:
@@ -35,7 +36,7 @@ __invalid_entry: .section .vectors ENTRY(_start) - .long CONFIG_SYS_INIT_SP_ADDR @ 0 - Reset stack pointer + .long SYS_INIT_SP_ADDR @ 0 - Reset stack pointer .long reset @ 1 - Reset .long __invalid_entry @ 2 - NMI .long __hard_fault_entry @ 3 - HardFault
arch/arm/mach-kirkwood/include/mach/config.h +0 -3
@@ -27,9 +27,6 @@#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ -/* Kirkwood has 2k of Security SRAM, use it for SP */ -#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 -#define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE#define MV_UART_CONSOLE_BASE KW_UART0_BASE#define MV_SATA_BASE KW_SATA_BASE
arch/arm/mach-mvebu/include/mach/config.h +0 -3
@@ -27,9 +27,6 @@#define CONFIG_SYS_L2_PL310 -/* end of 16M scrubbed by training in bootrom */ -#define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000 -#define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE/* Needed for SPI NOR booting in SPL */
arch/arm/mach-rmobile/lowlevel_init.S +1 -0
@@ -6,6 +6,7 @@ #include <config.h> #include <linux/linkage.h> +#include <system-constants.h> ENTRY(lowlevel_init) ldr r0, =MERAM_BASE
arch/arm/mach-rmobile/lowlevel_init_ca15.S +2 -1
@@ -8,6 +8,7 @@ #include <config.h> #include <linux/linkage.h> +#include <system-constants.h> ENTRY(lowlevel_init) #ifndef CONFIG_SPL_BUILD
@@ -75,7 +76,7 @@ _enable_actlr_smp: /* R8A7794 only (CA7) */ #endif _exit_init_l2_a15: - ldr r3, =(CONFIG_SYS_INIT_SP_ADDR) + ldr r3, =(SYS_INIT_SP_ADDR) sub sp, r3, #4 str lr, [sp]
arch/arm/mach-uniphier/arm32/late_lowlevel_init.S +2 -1
@@ -6,8 +6,9 @@ #include <config.h> #include <linux/linkage.h> +#include <system-constants.h> ENTRY(lowlevel_init) - ldr sp, = CONFIG_SYS_INIT_SP_ADDR + ldr sp, = SYS_INIT_SP_ADDR b uniphier_cache_disable ENDPROC(lowlevel_init)
arch/mips/cpu/start.S +2 -6
@@ -10,11 +10,7 @@ #include <asm/asm.h> #include <asm/regdef.h> #include <asm/mipsregs.h> - -#ifndef CONFIG_SYS_INIT_SP_ADDR -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_SP_OFFSET) -#endif +#include <system-constants.h> #ifdef CONFIG_32BIT # define STATUS_SET 0
@@ -44,7 +40,7 @@ .macro setup_stack_gd li t0, -16 - PTR_LI t1, CONFIG_SYS_INIT_SP_ADDR + PTR_LI t1, SYS_INIT_SP_ADDR and sp, t1, t0 # force 16 byte alignment PTR_SUBU \ sp, sp, GD_SIZE # reserve space for gd
arch/mips/mach-mtmips/mt7628/lowlevel_init.S +3 -8
@@ -12,16 +12,11 @@ #include <asm/mipsregs.h> #include <asm/addrspace.h> #include <asm/asm.h> +#include <system-constants.h> #include "mt7628.h" -/* Set temporary stack address range */ -#ifndef CONFIG_SYS_INIT_SP_ADDR -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_SP_OFFSET) -#endif - #define CACHE_STACK_SIZE 0x4000 -#define CACHE_STACK_BASE (CONFIG_SYS_INIT_SP_ADDR - CACHE_STACK_SIZE) +#define CACHE_STACK_BASE (SYS_INIT_SP_ADDR - CACHE_STACK_SIZE) #define DELAY_USEC(us) ((58 * (us)) / 3)
@@ -134,7 +129,7 @@ NESTED(lowlevel_init, 0, ra) #if CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F) /* Set malloc base */ - li t0, (CONFIG_SYS_INIT_SP_ADDR + 15) & (~15) + li t0, (SYS_INIT_SP_ADDR + 15) & (~15) PTR_S t0, GD_MALLOC_BASE(k0) # gd->malloc_base offset #endif
arch/powerpc/cpu/mpc83xx/cpu_init.c +2 -1
@@ -6,6 +6,7 @@#include <common.h> #include <asm-offsets.h> #include <mpc83xx.h> +#include <system-constants.h> #include <ioports.h> #include <asm/global_data.h> #include <asm/io.h>
@@ -138,7 +139,7 @@ void cpu_init_f (volatile immap_t * im)0 ;/* Pointer is writable since we allocated a register for it */ - gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ; + gd = (gd_t *)SYS_INIT_SP_ADDR ;/* global data region was cleared in start.S */
arch/powerpc/cpu/mpc83xx/spl_minimal.c +2 -1
@@ -7,6 +7,7 @@#include <asm-offsets.h> #include <clock_legacy.h> #include <mpc83xx.h> +#include <system-constants.h> #include <time.h> #include <asm/global_data.h>
@@ -25,7 +26,7 @@ DECLARE_GLOBAL_DATA_PTR;void cpu_init_f (volatile immap_t * im) {/* Pointer is writable since we allocated a register for it */ - gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ; + gd = (gd_t *)SYS_INIT_SP_ADDR ;/* global data region was cleared in start.S */
arch/powerpc/cpu/mpc83xx/start.S +3 -2
@@ -13,6 +13,7 @@ #include <asm-offsets.h> #include <config.h> #include <mpc83xx.h> +#include <system-constants.h> #include <ppc_asm.tmpl> #include <ppc_defs.h>
@@ -229,8 +230,8 @@ in_flash: /* set up the stack pointer in our newly created * cache-ram; use r3 to keep the new SP for now to * avoid overiding the SP it uselessly */ - lis r3, CONFIG_SYS_INIT_SP_ADDR@h - ori r3, r3, CONFIG_SYS_INIT_SP_ADDR@l + lis r3, SYS_INIT_SP_ADDR@h + ori r3, r3, SYS_INIT_SP_ADDR@l /* r4 = end of GD area */ addi r4, r3, GENERATED_GBL_DATA_SIZE
arch/powerpc/cpu/mpc85xx/cpu_init_early.c +2 -1
@@ -4,6 +4,7 @@*/ #include <common.h> +#include <system-constants.h> #include <asm-offsets.h> #include <asm/global_data.h> #include <asm/processor.h>
@@ -94,7 +95,7 @@ void cpu_init_early_f(void *fdt)#endif /* Pointer is writable since we allocated a register for it */ - gd = (gd_t *)CONFIG_SYS_INIT_SP_ADDR ; + gd = (gd_t *)SYS_INIT_SP_ADDR ;/* gd area was zeroed during startup */
arch/powerpc/cpu/mpc85xx/start.S +3 -2
@@ -14,6 +14,7 @@ #include <asm-offsets.h> #include <config.h> #include <mpc85xx.h> +#include <system-constants.h> #include <ppc_asm.tmpl> #include <ppc_defs.h>
@@ -1160,8 +1161,8 @@ _start_cont: bne 1b #if CONFIG_VAL(SYS_MALLOC_F_LEN) - lis r4,CONFIG_SYS_INIT_SP_ADDR@h - ori r4,r4,CONFIG_SYS_INIT_SP_ADDR@l + lis r4,SYS_INIT_SP_ADDR@h + ori r4,r4,SYS_INIT_SP_ADDR@l addi r3,r3,16 /* Pre-relocation malloc area */ stw r3,GD_MALLOC_BASE(r4)
arch/riscv/cpu/start.S +2 -1
@@ -13,6 +13,7 @@ #include <config.h> #include <common.h> #include <elf.h> +#include <system-constants.h> #include <asm/encoding.h> #include <generated/asm-offsets.h>
@@ -94,7 +95,7 @@ call_board_init_f: #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK) li t1, CONFIG_SPL_STACK #else - li t1, CONFIG_SYS_INIT_SP_ADDR + li t1, SYS_INIT_SP_ADDR #endif and sp, t1, t0 /* force 16 byte alignment */
board/synopsys/iot_devkit/u-boot.lds +1 -0
@@ -5,6 +5,7 @@ */ #include <config.h> +#include <system-constants.h> MEMORY { ROM : ORIGIN = ROM_BASE, LENGTH = ROM_SIZE
configs/SBx81LIFKW_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifkw" CONFIG_IDENT_STRING="\nSBx81LIFKW" CONFIG_SYS_LOAD_ADDR=0x1000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_SILENT_CONSOLE=y
configs/SBx81LIFXCAT_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifxcat" CONFIG_IDENT_STRING="\nSBx81LIFXCAT" CONFIG_SYS_LOAD_ADDR=0x1000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_SILENT_CONSOLE=y
configs/a3y17lte_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_A3Y17LTE=y CONFIG_NR_DRAM_BANKS=8 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte" CONFIG_SYS_LOAD_ADDR=0x40001000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x40200e50 CONFIG_FIT=y CONFIG_USE_PREBOOT=y CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
configs/a5y17lte_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_A5Y17LTE=y CONFIG_NR_DRAM_BANKS=12 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte" CONFIG_SYS_LOAD_ADDR=0x40001000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x40200e50 CONFIG_FIT=y CONFIG_USE_PREBOOT=y CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
configs/a7y17lte_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_A7Y17LTE=y CONFIG_NR_DRAM_BANKS=12 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte" CONFIG_SYS_LOAD_ADDR=0x40001000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x40200e50 CONFIG_FIT=y CONFIG_USE_PREBOOT=y CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
configs/ae350_rv32_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_DEFAULT_DEVICE_TREE="ae350_32" CONFIG_SYS_LOAD_ADDR=0x100000 CONFIG_TARGET_AX25_AE350=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffe80 CONFIG_FIT=y CONFIG_SYS_MONITOR_BASE=0x88000000 CONFIG_BOOTDELAY=3
configs/ae350_rv32_spl_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_SYS_LOAD_ADDR=0x100000 CONFIG_TARGET_AX25_AE350=y CONFIG_RISCV_SMODE=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xffff00 CONFIG_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x00200000 CONFIG_SYS_MONITOR_BASE=0x88000000
configs/ae350_rv32_spl_xip_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_TARGET_AX25_AE350=y CONFIG_RISCV_SMODE=y CONFIG_XIP=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xffff00 CONFIG_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80010000 CONFIG_SYS_MONITOR_BASE=0x88000000
configs/ae350_rv32_xip_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_SYS_LOAD_ADDR=0x100000 CONFIG_TARGET_AX25_AE350=y CONFIG_XIP=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffe80 CONFIG_FIT=y CONFIG_SYS_MONITOR_BASE=0x88000000 CONFIG_BOOTDELAY=3
configs/ae350_rv64_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_SYS_LOAD_ADDR=0x100000 CONFIG_TARGET_AX25_AE350=y CONFIG_ARCH_RV64I=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffd70 CONFIG_FIT=y CONFIG_SYS_MONITOR_BASE=0x88000000 CONFIG_BOOTDELAY=3
configs/ae350_rv64_spl_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_TARGET_AX25_AE350=y CONFIG_ARCH_RV64I=y CONFIG_RISCV_SMODE=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffe70 CONFIG_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x00200000 CONFIG_SYS_MONITOR_BASE=0x88000000
configs/ae350_rv64_spl_xip_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ARCH_RV64I=y CONFIG_RISCV_SMODE=y CONFIG_XIP=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffe70 CONFIG_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80010000 CONFIG_SYS_MONITOR_BASE=0x88000000
configs/ae350_rv64_xip_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_TARGET_AX25_AE350=y CONFIG_ARCH_RV64I=y CONFIG_XIP=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffd70 CONFIG_FIT=y CONFIG_SYS_MONITOR_BASE=0x88000000 CONFIG_BOOTDELAY=3
configs/alt_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x50000000 CONFIG_ENV_ADDR=0xC0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4f000000 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_SPL_MAX_SIZE=0x4000
configs/am335x_baltos_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_SPL=y CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run findfdt; run usbboot;run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;run nandboot;"
configs/am335x_boneblack_vboot_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_CLOCK_SYNTHESIZER=y CONFIG_SPL=y CONFIG_ENV_OFFSET_REDUND=0x280000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_VERBOSE=y
configs/am335x_evm_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_AM335X_USB0_PERIPHERAL=y CONFIG_AM335X_USB1=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am335x_evm_spiboot_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SPL_LOAD_FIT=y CONFIG_OF_BOARD_SETUP=y
configs/am335x_guardian_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x81000000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030fef0 CONFIG_TIMESTAMP=y CONFIG_BOOTDELAY=0 CONFIG_AUTOBOOT_KEYED=y
configs/am335x_hs_evm_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_AM33XX=y CONFIG_CLOCK_SYNTHESIZER=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am335x_hs_evm_uart_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_SPL=y # CONFIG_SPL_FS_FAT is not set # CONFIG_SPL_LIBDISK_SUPPORT is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am335x_igep003x_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_SPL=y CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run findfdt;run mmcboot;run nandboot;run netboot;" CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/am335x_pdu001_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_LOCALVERSION="-EETS-1.0.0" CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_BOOTDELAY=1 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
configs/am335x_shc_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SERIES=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_ict_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SHC_ICT=y CONFIG_SERIES=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_netboot_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SHC_NETBOOT=y CONFIG_SERIES=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_sdboot_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SHC_SDBOOT=y CONFIG_SERIES=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_AUTOBOOT_KEYED=y
configs/am335x_sl50_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_ENV_OFFSET_REDUND=0x20000 CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
configs/am3517_evm_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_SPL_SYS_MALLOC_F_LEN=0x2500 CONFIG_SPL=y CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_BOOTDELAY=10 CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device $mmcdev; if run loadbootenv; then run importbootenv; fi; echo Checking if uenvcmd is set ...; if test -n $uenvcmd; then echo Running uenvcmd ...; run uenvcmd; fi; echo Running default loadimage ...; setenv bootfile zImage; if run loadimage; then run loadfdt; run mmcboot; fi; else run nandboot; fi" CONFIG_SPL_MAX_SIZE=0xec00
configs/am43xx_evm_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_AM43XX=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
configs/am43xx_evm_qspiboot_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEFAULT_DEVICE_TREE="am437x-sk-evm" CONFIG_AM43XX=y CONFIG_ENV_OFFSET_REDUND=0x120000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_QSPI_BOOT=y CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd" CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/am43xx_evm_rtconly_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_AM43XX=y CONFIG_SPL_RTC_DDR_SUPPORT=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
configs/am43xx_evm_usbhost_boot_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_DEFAULT_DEVICE_TREE="am437x-gp-evm" CONFIG_AM43XX=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
configs/am43xx_hs_evm_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_TI_SECURE_EMIF_PROTECTED_REGION_SIZE=0x01c00000 CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_OF_BOARD_SETUP=y
configs/am57xx_evm_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_OF_BOARD_SETUP=y
configs/am57xx_hs_evm_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037ff00 CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_OF_BOARD_SETUP=y
configs/am57xx_hs_evm_usb_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037ff00 CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80200000 # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am64x_evm_a53_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/am64x_evm_r5_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7019b800 CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000 CONFIG_USE_BOOTCOMMAND=y
configs/am65x_evm_a53_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/am65x_evm_r5_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c7effc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am65x_evm_r5_usbdfu_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c7effc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
configs/am65x_evm_r5_usbmsc_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c7effc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_USE_BOOTCOMMAND=y
configs/am65x_hs_evm_a53_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/am65x_hs_evm_r5_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c7effc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/ap121_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ARCH_ATH79=y CONFIG_DEBUG_UART=y CONFIG_SYS_MEMTEST_START=0x80100000 CONFIG_SYS_MEMTEST_END=0x83f00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xbd007fff CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs"
configs/ap143_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_TARGET_AP143=y CONFIG_DEBUG_UART=y CONFIG_SYS_MEMTEST_START=0x80100000 CONFIG_SYS_MEMTEST_END=0x83f00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xbd001fff CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs"
configs/ap152_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_TARGET_AP152=y CONFIG_DEBUG_UART=y CONFIG_SYS_MEMTEST_START=0x80100000 CONFIG_SYS_MEMTEST_END=0x83f00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xbd001fff CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs"
configs/apalis-imx8_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_SYS_LOAD_ADDR=0x80280000 CONFIG_SYS_MEMTEST_START=0x88000000 CONFIG_SYS_MEMTEST_END=0x89000000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/armadillo-800eva_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_TARGET_ARMADILLO_800EVA=y CONFIG_SYS_CLK_FREQ=50000000 CONFIG_SYS_LOAD_ADDR=0x44000000 CONFIG_ENV_ADDR=0x40000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xe8083000 CONFIG_SYS_MONITOR_BASE=0x00000000 CONFIG_BOOTDELAY=3 # CONFIG_CMDLINE_EDITING is not set
configs/arndale_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL=y CONFIG_IDENT_STRING=" for ARNDALE" CONFIG_SYS_LOAD_ADDR=0x43e00000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x2050000 CONFIG_FIT=y CONFIG_FIT_BEST_MATCH=y CONFIG_USE_PREBOOT=y
configs/at91sam9m10g45ek_mmc_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_BASE=0xffffee00 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x70003f00 CONFIG_SD_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/at91sam9m10g45ek_nandflash_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_ENV_OFFSET_REDUND=0x100000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x70003f00 CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/at91sam9n12ek_mmc_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x303f00 CONFIG_SD_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/at91sam9n12ek_nandflash_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_ENV_OFFSET_REDUND=0x100000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x303f00 CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/at91sam9n12ek_spiflash_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x303f00 CONFIG_SPI_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/at91sam9x5ek_dataflash_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ef0 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/at91sam9x5ek_mmc_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ef0 CONFIG_FIT=y CONFIG_SD_BOOT=y CONFIG_BOOTDELAY=3
configs/at91sam9x5ek_nandflash_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_ENV_OFFSET_REDUND=0x100000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ef0 CONFIG_FIT=y CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=3
configs/at91sam9x5ek_spiflash_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ef0 CONFIG_FIT=y CONFIG_SPI_BOOT=y CONFIG_BOOTDELAY=3
configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART=y CONFIG_SYS_MEMTEST_START=0x00000000 CONFIG_SYS_MEMTEST_END=0x00001000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x8000000 CONFIG_REMAKE_ELF=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/axs101_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_CLOCK=33333333 CONFIG_SYS_CLK_FREQ=750000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS3,115200n8"
configs/axs103_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_CLOCK=33333333 CONFIG_SYS_CLK_FREQ=100000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS3,115200n8"
configs/bananapi-m5_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING="bpi-m5" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/bcm963158_ram_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEFAULT_DEVICE_TREE="bcm963158" CONFIG_SYS_LOAD_ADDR=0x10000000 CONFIG_TARGET_BCM963158=y CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x11000000 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_RSASSA_PSS=y
configs/bcm96753ref_ram_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ARMV7_LPAE=y CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_TARGET_BCM96753REF=y CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x2000000 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_CIPHER=y
configs/bcm968360bg_ram_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="bcm968360bg" CONFIG_SYS_LOAD_ADDR=0x10000000 CONFIG_TARGET_BCM968360BG=y CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x11000000 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_VERBOSE=y
configs/bcm968580xref_ram_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="bcm968580xref" CONFIG_SYS_LOAD_ADDR=0x10000000 CONFIG_TARGET_BCM968580XREF=y CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x11000000 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_VERBOSE=y
configs/bcm_ns3_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_ENV_SIZE=0x80000 CONFIG_DEFAULT_DEVICE_TREE="ns3-board" CONFIG_SYS_LOAD_ADDR=0x80080000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x0 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_SIGNATURE_MAX_SIZE=0x20000000
configs/beelink-gsking-x_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" beelink" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/beelink-gtking_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" beelink" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/beelink-gtkingpro_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" beelink" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/blanche_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_R8A7792=y CONFIG_TARGET_BLANCHE=y CONFIG_SYS_LOAD_ADDR=0x50000000 CONFIG_ENV_ADDR=0x40000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4f000000 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_HUSH_PARSER=y
configs/brppt1_mmc_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL=y CONFIG_ENV_OFFSET_REDUND=0x50000 CONFIG_SYS_LOAD_ADDR=0x80000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 # CONFIG_EXPERT is not set # CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y
configs/brppt1_nand_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_BRPPT1=y CONFIG_SPL_SERIAL=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x80000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 # CONFIG_EXPERT is not set # CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y
configs/brppt1_spi_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_ENV_OFFSET_REDUND=0x30000 CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x80000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 # CONFIG_EXPERT is not set # CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y
configs/brsmarc1_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_ENV_OFFSET_REDUND=0x30000 CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x80000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 # CONFIG_EXPERT is not set # CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y
configs/brxre1_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000 CONFIG_SPL=y CONFIG_ENV_OFFSET_REDUND=0x50000 CONFIG_SYS_LOAD_ADDR=0x80000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 # CONFIG_EXPERT is not set # CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y
configs/bubblegum_96_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_MACH_S900=y CONFIG_IDENT_STRING="\nBubblegum-96" CONFIG_SYS_LOAD_ADDR=0x7ffc0 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1107ff00 CONFIG_BOOTDELAY=5 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyOWL5,115200n8"
configs/cgtqmx8_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_FIT=y CONFIG_SPL_LOAD_FIT=y
configs/chiliboard_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_ENV_OFFSET_REDUND=0x22000 CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030fef0 CONFIG_TIMESTAMP=y CONFIG_BOOTDELAY=1 CONFIG_BOOTCOMMAND="run mmcboot; run nandboot; run netboot"
configs/chromebit_mickey_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_SPL_PAYLOAD="u-boot.img" CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-veyron-mickey.dtb" # CONFIG_DISPLAY_CPUINFO is not set
configs/chromebook_bob_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-gru-bob.dtb" # CONFIG_DISPLAY_CPUINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y
configs/chromebook_jerry_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_SPL_PAYLOAD="u-boot.img" CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-veyron-jerry.dtb" CONFIG_SILENT_CONSOLE=y
configs/chromebook_kevin_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-gru-kevin.dtb" # CONFIG_DISPLAY_CPUINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y
configs/chromebook_minnie_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_SPL_PAYLOAD="u-boot.img" CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-veyron-minnie.dtb" CONFIG_SILENT_CONSOLE=y
configs/chromebook_speedy_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_SPL_PAYLOAD="u-boot.img" CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-veyron-speedy.dtb" CONFIG_SILENT_CONSOLE=y
configs/clearfog_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/clearfog_gt_8k_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/cm_t335_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_SPL=y CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_TIMESTAMP=y # CONFIG_USE_BOOTCOMMAND is not set CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/cm_t43_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4033ff00 CONFIG_BOOTCOMMAND="mmc dev 0; if mmc rescan; then if run loadbootscript; then run bootscript; fi; fi; mmc dev 1; if mmc rescan; then run emmcboot; fi;" CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_CPUINFO is not set
configs/colibri-imx8x_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_SYS_LOAD_ADDR=0x80280000 CONFIG_SYS_MEMTEST_START=0x88000000 CONFIG_SYS_MEMTEST_END=0x89000000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/controlcenterdc_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_OF_BOARD_FIXUP=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_FIT_VERBOSE=y
configs/cortina_presidio-asic-base_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" CONFIG_IDENT_STRING="Presidio-SoC" CONFIG_SYS_LOAD_ADDR=0x10000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_REMAKE_ELF=y CONFIG_SUPPORT_RAW_INITRD=y CONFIG_SHOW_BOOT_PROGRESS=y
configs/cortina_presidio-asic-emmc_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" CONFIG_IDENT_STRING="Presidio-SoC" CONFIG_SYS_LOAD_ADDR=0x10000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_REMAKE_ELF=y CONFIG_SUPPORT_RAW_INITRD=y CONFIG_SHOW_BOOT_PROGRESS=y
configs/cortina_presidio-asic-pnand_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" CONFIG_IDENT_STRING="Presidio-SoC" CONFIG_SYS_LOAD_ADDR=0x10000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 CONFIG_REMAKE_ELF=y CONFIG_SUPPORT_RAW_INITRD=y CONFIG_SHOW_BOOT_PROGRESS=y
configs/corvus_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL=y CONFIG_ENV_OFFSET_REDUND=0x180000 CONFIG_SYS_LOAD_ADDR=0x70000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x70007f00 CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/crs305-1g-4s-bit_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs305-1g-4s-bit" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/crs305-1g-4s_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs305-1g-4s" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/crs326-24g-2s-bit_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs326-24g-2s-bit" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/crs326-24g-2s_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs326-24g-2s" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/crs328-4c-20s-4s-bit_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs328-4c-20s-4s-bit" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/crs328-4c-20s-4s_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs328-4c-20s-4s" CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/cubieboard7_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_MACH_S700=y CONFIG_IDENT_STRING="\ncubieboard7" CONFIG_SYS_LOAD_ADDR=0x7ffc0 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1107ff00 CONFIG_BOOTDELAY=5 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyOWL3,115200n8"
configs/d2net_v2_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net" CONFIG_IDENT_STRING=" D2 v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/da850evm_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0xc0700000 CONFIG_LTO=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0000f20 CONFIG_DYNAMIC_SYS_CLK_FREQ=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/da850evm_direct_nor_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEFAULT_DEVICE_TREE="da850-evm" CONFIG_SYS_LOAD_ADDR=0xc0700000 CONFIG_ENV_ADDR=0x60100000 CONFIG_LTO=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x8001ff00 CONFIG_DYNAMIC_SYS_CLK_FREQ=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/da850evm_nand_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0xc0700000 CONFIG_LTO=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0000f20 CONFIG_DYNAMIC_SYS_CLK_FREQ=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/db-88f6720_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y
configs/db-88f6820-amc_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=200000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_BOOTDELAY=3
configs/db-88f6820-gp_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/db-mv784mp-gp_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y
configs/db-xc3-24g4xg_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BUILD_TARGET="u-boot.kwb" CONFIG_SYS_MEMTEST_START=0x00800000 CONFIG_SYS_MEMTEST_END=0x00ffffff +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_FIT_BEST_MATCH=y
configs/deneb_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_IDENT_STRING=" ##v01.06" CONFIG_SPL_LOAD_IMX_CONTAINER=y CONFIG_IMX_CONTAINER_CFG="board/siemens/capricorn/uboot-container.cfg" CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_OF_SYSTEM_SETUP=y
configs/devkit3250_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_TEXT_BASE=0x00000000 CONFIG_SPL_SERIAL=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x80008000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f20 CONFIG_BOOTDELAY=1 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8"
configs/devkit8000_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_TARGET_DEVKIT8000=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_BOOTCOMMAND="run autoboot" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SPL_MAX_SIZE=0xec00
configs/dns325_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_ENV_OFFSET=0xE0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dns325" CONFIG_IDENT_STRING="\nD-Link DNS-325" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/dockstar_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ENV_OFFSET=0x80000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dockstar" CONFIG_IDENT_STRING="\nSeagate FreeAgent DockStar" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/dra7xx_evm_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037fef0 CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80200000 # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/dra7xx_hs_evm_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037fef0 CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80200000 # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/dra7xx_hs_evm_usb_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_SPI=y CONFIG_ARMV7_LPAE=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4037fef0 CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80200000 # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/draco_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x81000000 CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_BOOTDELAY=3 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
configs/dragonboard410c_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEFAULT_DEVICE_TREE="dragonboard410c" CONFIG_IDENT_STRING="\nQualcomm-DragonBoard 410C" CONFIG_SYS_LOAD_ADDR=0x80080000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x8007fff0 CONFIG_REMAKE_ELF=y # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/dragonboard820c_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_DRAGONBOARD820C=y CONFIG_IDENT_STRING="\nQualcomm-DragonBoard 820C" CONFIG_SYS_LOAD_ADDR=0x80080000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x8007fff0 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyMSM0,115200n8" # CONFIG_USE_BOOTCOMMAND is not set
configs/dreamplug_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dreamplug" CONFIG_IDENT_STRING="\nMarvell-DreamPlug" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x100000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/ds109_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ds109" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x3D0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="setenv ethact egiga0; ${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;"
configs/ds414_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200 ip=off initrd=0x8000040,8M root=/dev/md0 rw syno_hw_version=DS414r1 ihd_num=4 netif_num=2 flash_size=8 SataLedSpecial=1 HddHotplug=1"
configs/durian_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_SYS_LOAD_ADDR=0x90000000 CONFIG_SYS_PCI_64BIT=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x87f00000 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyAMA0,115200 earlycon=pl011,0x28001000 root=/dev/sda2 rw" # CONFIG_DISPLAY_CPUINFO is not set
configs/ea-lpc3250devkitv2_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_TARGET_EA_LPC3250DEVKITV2=y CONFIG_DEFAULT_DEVICE_TREE="lpc3250-ea3250" CONFIG_SYS_LOAD_ADDR=0x80100000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f20 CONFIG_HAS_BOARD_SIZE_LIMIT=y CONFIG_BOARD_SIZE_LIMIT=1048575 # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
configs/edminiv2_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL=y CONFIG_IDENT_STRING=" EDMiniV2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0xFFF84000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xf40 CONFIG_BOOTDELAY=3 # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_ARCH_MISC_INIT=y
configs/elgin-rv1108_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_BASE=0x10210000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x62000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 # CONFIG_USE_BOOTCOMMAND is not set CONFIG_DEFAULT_FDT_FILE="rv1108-elgin-r1.dtb" # CONFIG_DISPLAY_CPUINFO is not set
configs/emsdp_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x1000 CONFIG_DEFAULT_DEVICE_TREE="emsdp" CONFIG_SYS_CLK_FREQ=40000000 CONFIG_SYS_LOAD_ADDR=0x10000000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x10100000 # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set CONFIG_BOARD_EARLY_INIT_R=y CONFIG_HUSH_PARSER=y
configs/espresso7420_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x4000 CONFIG_DEFAULT_DEVICE_TREE="exynos7420-espresso7420" CONFIG_IDENT_STRING=" for ESPRESSO7420" CONFIG_SYS_LOAD_ADDR=0x43e00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x2158000 # CONFIG_AUTOBOOT is not set CONFIG_SILENT_CONSOLE=y CONFIG_CONSOLE_MUX=y
configs/etamin_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x81000000 CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 CONFIG_BOOTDELAY=3 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
configs/evb-px30_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART_BASE=0xFF160000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x400000 CONFIG_TPL_SYS_MALLOC_F_LEN=0x600 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/evb-px5_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_ANDROID_BOOT_IMAGE=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/evb-rk3036_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0x20068000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x60800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3036-evb.dtb"
configs/evb-rk3128_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0x20068000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x60800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 CONFIG_FIT=y CONFIG_DEFAULT_FDT_FILE="rk3128-evb.dtb" # CONFIG_DISPLAY_CPUINFO is not set
configs/evb-rk3229_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART_BASE=0x11030000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x61800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x61100000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y
configs/evb-rk3288_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEBUG_UART_BASE=0xff690000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/evb-rk3308_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEBUG_UART_BASE=0xFF0C0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x800000 CONFIG_ANDROID_BOOT_IMAGE=y CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/evb-rk3328_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/evb-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-evb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/evb-rk3568_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART_BASE=0xFE660000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0xc00800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y
configs/evb-rv1108_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_BASE=0x10210000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x62000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 CONFIG_BOOTCOMMAND="sf probe;sf read 0x62000000 0x140800 0x500000;dcache off;go 0x62000000" CONFIG_DEFAULT_FDT_FILE="rv1108-evb.dtb" # CONFIG_DISPLAY_CPUINFO is not set
configs/ficus-rk3399_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000 CONFIG_SPL_PAD_TO=0x7f8000
configs/firefly-px30_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_DEBUG_UART_BASE=0xFF160000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x400000 CONFIG_TPL_SYS_MALLOC_F_LEN=0x600 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/firefly-rk3288_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEBUG_UART_BASE=0xff690000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-firefly.dtb"
configs/firefly-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-firefly.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_MISC_INIT_R=y
configs/gardena-smart-gateway-at91sam_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_DEBUG_UART_BASE=0xfffff200 CONFIG_DEBUG_UART_CLOCK=132000000 CONFIG_SYS_LOAD_ADDR=0x22000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003f00 CONFIG_FIT=y CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=0
configs/geekbox_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF690000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3368-geekbox.dtb" # CONFIG_DISPLAY_CPUINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y
configs/giedi_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_IDENT_STRING=" ##v01.07" CONFIG_SPL_LOAD_IMX_CONTAINER=y CONFIG_IMX_CONTAINER_CFG="board/siemens/capricorn/uboot-container.cfg" CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_OF_SYSTEM_SETUP=y
configs/goflexhome_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ENV_OFFSET=0xC0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-goflexnet" CONFIG_IDENT_STRING="\nSeagate GoFlex Home" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/gose_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x50000000 CONFIG_ENV_ADDR=0xC0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4f000000 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_SPL_MAX_SIZE=0x4000
configs/grpeach_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEFAULT_DEVICE_TREE="r7s72100-gr-peach-u-boot" CONFIG_RZA1=y CONFIG_SYS_CLK_FREQ=66666666 CONFIG_SYS_LOAD_ADDR=0x20400000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20900000 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="ignore_loglevel"
configs/guruplug_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_ENV_OFFSET=0xE0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus" CONFIG_IDENT_STRING="\nMarvell-GuruPlug" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_HAS_BOARD_SIZE_LIMIT=y CONFIG_BOARD_SIZE_LIMIT=917504
configs/helios4_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/highbank_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0xFFF88000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000000 CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_AUTOBOOT_KEYED=y
configs/hikey960_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_DEFAULT_DEVICE_TREE="hi3660-hikey960" CONFIG_IDENT_STRING="\nHikey960" CONFIG_SYS_LOAD_ADDR=0x80000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7fff0 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyAMA6,115200n8 root=/dev/mmcblk0p2 rw"
configs/hikey_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_DEFAULT_DEVICE_TREE="hi6220-hikey" CONFIG_IDENT_STRING="hikey" CONFIG_SYS_LOAD_ADDR=0x80000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7fff0 CONFIG_REMAKE_ELF=y CONFIG_BOOTDELAY=10 CONFIG_USE_BOOTARGS=y
configs/hsdk_4xd_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=33333333 CONFIG_SYS_CLK_FREQ=500000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8" CONFIG_BOARD_EARLY_INIT_F=y
configs/hsdk_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=33333333 CONFIG_SYS_CLK_FREQ=500000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8" CONFIG_BOARD_EARLY_INIT_F=y
configs/ib62x0_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_ENV_OFFSET=0xE0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ib62x0" CONFIG_IDENT_STRING=" RaidSonic ICY BOX IB-NAS62x0" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/iconnect_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_ENV_OFFSET=0x80000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-iconnect" CONFIG_IDENT_STRING=" Iomega iConnect" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/igep00x0_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_TARGET_OMAP3_IGEP00X0=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
configs/imgtec_xilfpga_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_MIPS_CACHE_SETUP=y CONFIG_MIPS_CACHE_DISABLE=y # CONFIG_MIPS_BOOT_ENV_LEGACY is not set CONFIG_MIPS_BOOT_FDT=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x87fff000 CONFIG_TIMESTAMP=y CONFIG_BOOTDELAY=5 # CONFIG_DISPLAY_BOARDINFO is not set
configs/imx8qm_mek_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL=y CONFIG_SPL_LOAD_IMX_CONTAINER=y CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qm_mek/uboot-container.cfg" CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_OF_SYSTEM_SETUP=y
configs/imx8qm_rom7720_a1_4G_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_FIT=y CONFIG_SPL_LOAD_FIT=y
configs/imx8qxp_mek_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL=y CONFIG_SPL_LOAD_IMX_CONTAINER=y CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qxp_mek/uboot-container.cfg" CONFIG_SYS_LOAD_ADDR=0x80280000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_OF_SYSTEM_SETUP=y
configs/imxrt1020-evk_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SIZE_LIMIT=0x20000 CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x20209000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20240000 CONFIG_SD_BOOT=y # CONFIG_USE_BOOTCOMMAND is not set # CONFIG_DISPLAY_CPUINFO is not set
configs/imxrt1050-evk_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL_SIZE_LIMIT=0x20000 CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x20209000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20280000 CONFIG_SD_BOOT=y # CONFIG_USE_BOOTCOMMAND is not set CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y
configs/inetspace_v2_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-is2" CONFIG_IDENT_STRING=" IS v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/integratorap_cm720t_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_CM720T=y CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x8000 CONFIG_SYS_LOAD_ADDR=0x7fc0 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAM0 console=tty" CONFIG_USE_BOOTCOMMAND=y
configs/integratorap_cm920t_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_CM920T=y CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x8000 CONFIG_SYS_LOAD_ADDR=0x7fc0 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAM0 console=tty" CONFIG_USE_BOOTCOMMAND=y
configs/integratorap_cm926ejs_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_CM926EJ_S=y CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x8000 CONFIG_SYS_LOAD_ADDR=0x7fc0 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAM0 console=tty" CONFIG_USE_BOOTCOMMAND=y
configs/integratorap_cm946es_defconfig +2 -0
@@ -7,6 +7,8 @@ CONFIG_CM946ES=y CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x8000 CONFIG_SYS_LOAD_ADDR=0x7fc0 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAM0 console=tty" CONFIG_USE_BOOTCOMMAND=y
configs/integratorcp_cm1136_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_SECT_SIZE=0x40000 CONFIG_SYS_LOAD_ADDR=0x7fc0 CONFIG_ENV_ADDR=0x24F00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_SYS_MONITOR_BASE=0x27F40000 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAMA0 console=tty ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0"
configs/integratorcp_cm920t_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_SECT_SIZE=0x40000 CONFIG_SYS_LOAD_ADDR=0x7fc0 CONFIG_ENV_ADDR=0x24F00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_SYS_MONITOR_BASE=0x27F40000 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAMA0 console=tty ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0"
configs/integratorcp_cm926ejs_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_SECT_SIZE=0x40000 CONFIG_SYS_LOAD_ADDR=0x7fc0 CONFIG_ENV_ADDR=0x24F00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_SYS_MONITOR_BASE=0x27F40000 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAMA0 console=tty ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0"
configs/integratorcp_cm946es_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_SECT_SIZE=0x40000 CONFIG_SYS_LOAD_ADDR=0x7fc0 CONFIG_ENV_ADDR=0x24F00000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x7ffff20 CONFIG_SYS_MONITOR_BASE=0x27F40000 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="root=/dev/mtdblock0 console=ttyAMA0 console=tty ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0"
configs/iot2050_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_ENV_OFFSET_REDUND=0x6a0000 CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80100000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set
configs/iot_devkit_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEFAULT_DEVICE_TREE="iot_devkit" CONFIG_SYS_CLK_FREQ=16000000 CONFIG_SYS_LOAD_ADDR=0x30000000 CONFIG_LOCALVERSION="-iotdk-1.0" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80008000 # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set CONFIG_SYS_PROMPT="IoTDK# " CONFIG_SYS_CBSIZE=256
configs/j7200_evm_a72_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/j7200_evm_r5_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41cf5bfc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
configs/j721e_evm_a72_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/j721e_evm_r5_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41cf5bfc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
configs/j721e_hs_evm_a72_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/j721e_hs_evm_r5_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41cf5bfc # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
configs/j721s2_evm_a72_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y # CONFIG_PSCI_RESET is not set CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
configs/j721s2_evm_r5_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c76000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_LOAD_FIT=y CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
configs/jethub_j100_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" jethubj100" CONFIG_SYS_LOAD_ADDR=0x01000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/jethub_j80_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" jethubj80" CONFIG_SYS_LOAD_ADDR=0x01000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_CONSOLE_MUX=y
configs/k2e_evm_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run init_${boot}; run get_mon_${boot} run_mon; run get_kern_${boot}; run init_fw_rd_${boot}; run get_fdt_${boot}; run run_kern"
configs/k2e_hs_evm_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_ENV_SIZE=0x40000 CONFIG_ENV_OFFSET=0x100000 CONFIG_DEFAULT_DEVICE_TREE="keystone-k2e-evm" CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run run_mon_hs; run init_${boot}; run get_fit_${boot}; bootm ${addr_fit}#${name_fdt}"
configs/k2g_evm_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc09ff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run get_mon_${boot} run_mon; run set_name_pmmc get_pmmc_${boot} run_pmmc; run get_kern_${boot}; run init_fw_rd_${boot}; run get_fdt_${boot}; run run_kern"
configs/k2g_hs_evm_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_K2G_EVM=y CONFIG_ENV_SIZE=0x40000 CONFIG_DEFAULT_DEVICE_TREE="keystone-k2g-evm" CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc09ff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run findfdt; run envboot; run run_mon_hs; run init_${boot}; run get_fit_${boot}; bootm ${addr_fit}#${name_fdt}"
configs/k2hk_evm_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc1fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run init_${boot}; run get_mon_${boot} run_mon; run get_kern_${boot}; run init_fw_rd_${boot}; run get_fdt_${boot}; run run_kern"
configs/k2hk_hs_evm_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_ENV_SIZE=0x40000 CONFIG_ENV_OFFSET=0x100000 CONFIG_DEFAULT_DEVICE_TREE="keystone-k2hk-evm" CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc1fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run run_mon_hs; run init_${boot}; run get_fit_${boot}; bootm ${addr_fit}#${name_fdt}"
configs/k2l_evm_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTCOMMAND="run init_${boot}; run get_mon_${boot} run_mon; run get_kern_${boot}; run init_fw_rd_${boot}; run get_fdt_${boot}; run run_kern"
configs/k2l_hs_evm_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_K2L_EVM=y CONFIG_ENV_SIZE=0x40000 CONFIG_ENV_OFFSET=0x100000 CONFIG_DEFAULT_DEVICE_TREE="keystone-k2l-evm" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0fff10 CONFIG_TIMESTAMP=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_BOOTCOMMAND=y
configs/khadas-edge-captain-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-khadas-edge-captain.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/khadas-edge-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-khadas-edge.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/khadas-edge-v-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-khadas-edge-v.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/khadas-vim2_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim2" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_CONSOLE_MUX=y
configs/khadas-vim3_android_ab_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim3_android_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim3_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim3l_android_ab_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3l" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim3l_android_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3l" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim3l_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim3l" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/khadas-vim_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_CONSOLE_MUX=y
configs/km_kirkwood_128m16_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_ENV_OFFSET_REDUND=0x2000 CONFIG_IDENT_STRING="\nHitachi Power Grids Kirkwood 128M16" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_KM_KIRKWOOD_128M16=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/km_kirkwood_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_ENV_OFFSET_REDUND=0x2000 CONFIG_IDENT_STRING="\nHitachi Power Grids Kirkwood" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_KM_KIRKWOOD=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/km_kirkwood_pci_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_IDENT_STRING="\nHitachi Power Grids Kirkwood PCI" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_KM_FPGA_CONFIG=y CONFIG_KM_KIRKWOOD_PCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/kmcoge5un_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3 CONFIG_KM_ENV_IS_IN_SPI_NOR=y CONFIG_KM_PIGGY4_88E6352=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/kmnusa_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_KM_FPGA_CONFIG=y CONFIG_KM_ENV_IS_IN_SPI_NOR=y CONFIG_KM_PIGGY4_88E6352=y CONFIG_KM_NUSA=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/kmsuse2_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_KM_FPGA_FORCE_CONFIG=y CONFIG_KM_FPGA_NO_RESET=y CONFIG_KM_ENV_IS_IN_SPI_NOR=y CONFIG_KM_SUSE2=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" "
configs/koelsch_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x50000000 CONFIG_ENV_ADDR=0xC0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4f000000 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_SPL_MAX_SIZE=0x4000
configs/kontron_sl28_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_ARMV8_PSCI_RELOCATE=y CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800eff0 CONFIG_MP=y CONFIG_FIT=y CONFIG_SPL_LOAD_FIT=y
configs/kylin-rk3036_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_DEBUG_UART_BASE=0x20068000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x60800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3036-kylin.dtb"
configs/lager_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x50000000 CONFIG_ENV_ADDR=0xC0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4f000000 CONFIG_FIT=y CONFIG_BOOTDELAY=3 CONFIG_SPL_MAX_SIZE=0x4000
configs/leez-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-leez-p710.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/legoev3_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x4000 CONFIG_DEFAULT_DEVICE_TREE="da850-lego-ev3" CONFIG_SYS_LOAD_ADDR=0xc0700000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80010000 CONFIG_DYNAMIC_SYS_CLK_FREQ=y CONFIG_BOOTDELAY=0 CONFIG_AUTOBOOT_KEYED=y
configs/libretech-ac_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" libretech-ac" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y
configs/libretech-cc_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" libretech-cc" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/libretech-cc_v2_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" libretech-cc-v2" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y
configs/libretech-s905d-pc_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" libretech-s905d-pc" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y
configs/libretech-s912-pc_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" libretech-s912-pc" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y
configs/lion-rk3368_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y
configs/ls1012a2g5rdb_qspi_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012afrdm_qspi_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_QSPI_AHB_INIT=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012afrwy_qspi_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012aqds_qspi_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012ardb_qspi_SECURE_BOOT_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1012ardb_qspi_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y
configs/ls1043aqds_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_lpuart_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_nand_defconfig +2 -0
@@ -30,6 +30,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_nor_ddr3_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_qspi_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_sdcard_ifc_defconfig +2 -0
@@ -31,6 +31,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043aqds_sdcard_qspi_defconfig +2 -0
@@ -30,6 +30,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_SECURE_BOOT_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" CONFIG_FSL_LS_PPA=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" CONFIG_FSL_LS_PPA=y CONFIG_ENV_ADDR=0x60300000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_nand_SECURE_BOOT_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_nand_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1043ardb_sdcard_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_SECURE_BOOT_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_lpuart_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_nand_defconfig +2 -0
@@ -30,6 +30,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_qspi_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_sdcard_ifc_defconfig +2 -0
@@ -31,6 +31,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046aqds_sdcard_qspi_defconfig +2 -0
@@ -30,6 +30,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_emmc_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_qspi_SECURE_BOOT_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_FSL_LS_PPA=y CONFIG_QSPI_AHB_INIT=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_qspi_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_QSPI_AHB_INIT=y CONFIG_ENV_ADDR=0x40300000 CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_qspi_spl_defconfig +2 -0
@@ -24,6 +24,8 @@ CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1046ardb_sdcard_defconfig +2 -0
@@ -22,6 +22,8 @@ CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls1088aqds_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_ENV_ADDR=0x80300000 CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088aqds_qspi_SECURE_BOOT_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088aqds_qspi_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088aqds_sdcard_ifc_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL=y CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088aqds_sdcard_qspi_defconfig +2 -0
@@ -27,6 +27,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088ardb_qspi_SECURE_BOOT_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088ardb_qspi_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088ardb_sdcard_qspi_SECURE_BOOT_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SPL=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls1088ardb_sdcard_qspi_defconfig +2 -0
@@ -27,6 +27,8 @@ CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0x9fffffff CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2080aqds_SECURE_BOOT_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_FSL_QIXIS=y # CONFIG_QIXIS_I2C_ACCESS is not set CONFIG_FSL_LS_PPA=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2080aqds_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_FSL_QIXIS=y CONFIG_FSL_LS_PPA=y CONFIG_ENV_ADDR=0x80300000 CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2080aqds_nand_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT=y
configs/ls2080aqds_qspi_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds" CONFIG_FSL_USE_PCA9547_MUX=y CONFIG_FSL_QIXIS=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT=y
configs/ls2080aqds_sdcard_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT_VERBOSE=y
configs/ls2080ardb_SECURE_BOOT_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_FSL_QIXIS=y # CONFIG_QIXIS_I2C_ACCESS is not set CONFIG_FSL_LS_PPA=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2080ardb_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_FSL_QIXIS=y CONFIG_FSL_LS_PPA=y CONFIG_ENV_ADDR=0x80300000 CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2080ardb_nand_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 CONFIG_REMAKE_ELF=y CONFIG_MP=y CONFIG_FIT=y
configs/ls2081ardb_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_FSL_QIXIS=y CONFIG_FSL_LS_PPA=y CONFIG_QSPI_AHB_INIT=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2088ardb_qspi_SECURE_BOOT_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_VOL_MONITOR_IR36021_SET=y CONFIG_FSL_LS_PPA=y CONFIG_QSPI_AHB_INIT=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/ls2088ardb_qspi_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_FSL_LS_PPA=y CONFIG_QSPI_AHB_INIT=y CONFIG_ENV_ADDR=0x20300000 CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 # CONFIG_SYS_MALLOC_F is not set CONFIG_REMAKE_ELF=y CONFIG_MP=y
configs/lschlv2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lschlv2" CONFIG_IDENT_STRING=" LS-CHLv2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_API=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_BOOTDELAY=3
configs/lsxhl_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lsxhl" CONFIG_IDENT_STRING=" LS-XHL" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_API=y CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_BOOTDELAY=3
configs/maxbcm_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=250000000 CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 CONFIG_BOOTDELAY=3 CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/microchip_mpfs_icicle_defconfig +2 -0
@@ -8,6 +8,8 @@ CONFIG_TARGET_MICROCHIP_ICICLE=y CONFIG_ARCH_RV64I=y CONFIG_RISCV_SMODE=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 CONFIG_FIT=y CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y
configs/miqi-rk3288_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEBUG_UART_BASE=0xff690000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x100000 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3288-miqi.dtb"
configs/mk808_defconfig +2 -0
@@ -25,6 +25,8 @@ CONFIG_SPL_FS_FAT=y CONFIG_SYS_LOAD_ADDR=0x70800800 CONFIG_SPL_PAYLOAD="u-boot.bin" CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x78000000 CONFIG_SD_BOOT=y CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="rk3066a-mk808.dtb"
configs/mt7623a_unielec_u7623_02_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEFAULT_DEVICE_TREE="mt7623a-unielec-u7623-02-emmc" CONFIG_TARGET_MT7623=y CONFIG_SYS_LOAD_ADDR=0x84000000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x81ffff10 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_BOOTDELAY=3
configs/mt7623n_bpir2_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEFAULT_DEVICE_TREE="mt7623n-bananapi-bpi-r2" CONFIG_TARGET_MT7623=y CONFIG_SYS_LOAD_ADDR=0x84000000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x81ffff10 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_BOOTDELAY=3
configs/mt7629_rfb_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SPL_STACK_R_ADDR=0x40800000 CONFIG_SYS_LOAD_ADDR=0x42007f1c CONFIG_SPL_PAYLOAD="u-boot-lzma.img" CONFIG_BUILD_TARGET="u-boot-mtk.bin" +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41fffef0 CONFIG_SPL_IMAGE="spl/u-boot-spl-mtk.bin" CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/mvebu_crb_cn9130_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/mvebu_db-88f3720_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x6000000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/mvebu_db_armada8k_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/mvebu_db_cn9130_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/mvebu_espressobin-88f3720_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x6000000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y
configs/mvebu_mcbin-88f8040_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/mvebu_puzzle-m801-88f8040_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds, to stop use 's' key\n"
configs/nanopc-t4-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nanopi-k2_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" nanopi-k2" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/nanopi-m4-2gb-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4-2gb.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nanopi-m4-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nanopi-m4b-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4b.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nanopi-neo4-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-neo4.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nanopi-r2s-rk3328_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_DEBUG_UART_BASE=0xFF130000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/nanopi-r4s-rk3399_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_BASE=0xFF1A0000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-r4s.dtb" CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x2e000
configs/nas220_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_ENV_OFFSET=0xA0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas220" CONFIG_IDENT_STRING="\nNAS 220" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y
configs/net2big_v2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big" CONFIG_IDENT_STRING=" 2Big v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/netspace_lite_v2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2lite" CONFIG_IDENT_STRING=" NS v2 Lite" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/netspace_max_v2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2max" CONFIG_IDENT_STRING=" NS Max v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/netspace_mini_v2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2mini" CONFIG_IDENT_STRING=" NS v2 Mini" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/netspace_v2_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2" CONFIG_IDENT_STRING=" NS v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 # CONFIG_SYS_MALLOC_F is not set CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y
configs/nsa310s_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_ENV_OFFSET=0xE0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-nsa310s" CONFIG_IDENT_STRING="\nZyXEL NSA310S/320S 1/2-Bay Power Media Server" CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="setenv bootargs ${console} ${mtdparts} ${bootargs_root}; ubi part root; ubifsmount ubi:rootfs; ubifsload 0x800000 ${kernel}; ubifsload 0x700000 ${fdt}; ubifsumount; fdt addr 0x700000; fdt resize; fdt chosen; bootz 0x800000 - 0x700000"
configs/nsim_700_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_CLOCK=70000000 CONFIG_SYS_CLK_FREQ=70000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8"
configs/nsim_700be_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=70000000 CONFIG_SYS_CLK_FREQ=70000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8"
configs/nsim_hs38_defconfig +2 -0
@@ -11,6 +11,8 @@ CONFIG_DEBUG_UART_CLOCK=70000000 CONFIG_SYS_CLK_FREQ=70000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8"
configs/nsim_hs38be_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=70000000 CONFIG_SYS_CLK_FREQ=70000000 CONFIG_SYS_LOAD_ADDR=0x82000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80000f30 CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="console=ttyS0,115200n8"
configs/octeontx2_95xx_defconfig +2 -0
@@ -17,6 +17,8 @@ CONFIG_SYS_LOAD_ADDR=0x4000000 CONFIG_DEBUG_UART=y CONFIG_SYS_MEMTEST_START=0x04000000 CONFIG_SYS_MEMTEST_END=0x040f0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x40ffff0 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_SUPPORT_RAW_INITRD=y
configs/octeontx2_96xx_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x4000000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x40ffff0 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y
configs/octeontx_81xx_defconfig +2 -0
@@ -18,6 +18,8 @@ CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_SYS_MEMTEST_START=0x2800000 CONFIG_SYS_MEMTEST_END=0x28f0000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x28ffff0 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_SUPPORT_RAW_INITRD=y
configs/octeontx_83xx_defconfig +2 -0
@@ -16,6 +16,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x2800000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x28ffff0 CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y CONFIG_SUPPORT_RAW_INITRD=y
configs/odroid-c2_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" odroid-c2" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/odroid-c4_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" odroid-c4/hc4" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/odroid-go2_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_DEBUG_UART_BASE=0xFF160000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SYS_LOAD_ADDR=0x800800 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x400000 CONFIG_TPL_SYS_MALLOC_F_LEN=0x600 # CONFIG_ANDROID_BOOT_IMAGE is not set CONFIG_FIT=y
configs/odroid-hc4_defconfig +2 -0
@@ -13,6 +13,8 @@ CONFIG_IDENT_STRING=" odroid-hc4" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y CONFIG_AHCI=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/odroid-n2_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" odroid-n2/n2-plus" CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_DEBUG_UART=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000 CONFIG_REMAKE_ELF=y CONFIG_OF_BOARD_SETUP=y # CONFIG_DISPLAY_CPUINFO is not set
configs/odroid-xu3_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_IDENT_STRING=" for ODROID-XU3/XU4/HC1/HC2" CONFIG_SYS_MEM_TOP_HIDE=0x01600000 CONFIG_SYS_LOAD_ADDR=0x43e00000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x42e00000 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_FIT=y CONFIG_FIT_BEST_MATCH=y
configs/odroid_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_DEFAULT_DEVICE_TREE="exynos4412-odroid" CONFIG_SYS_MEM_TOP_HIDE=0x00100000 CONFIG_SYS_LOAD_ADDR=0x43e00000 CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x43dfff10 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_FIT=y CONFIG_FIT_VERBOSE=y
configs/omap35_logic_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL=y CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_ANDROID_BOOT_IMAGE=y CONFIG_BOOTCOMMAND="run autoboot" CONFIG_USE_PREBOOT=y
configs/omap35_logic_somlv_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL=y CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_ANDROID_BOOT_IMAGE=y CONFIG_SYS_MONITOR_BASE=0x10000000 CONFIG_BOOTCOMMAND="run autoboot"
configs/omap3_beagle_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_OMAP3_BEAGLE=y CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="omap3-beagle.dtb"
configs/omap3_evm_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_TARGET_OMAP3_EVM=y CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run envboot; run distro_bootcmd" CONFIG_USE_PREBOOT=y CONFIG_DEFAULT_FDT_FILE="omap3-evm.dtb"
configs/omap3_logic_defconfig +2 -0
@@ -14,6 +14,8 @@ CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL=y CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00 CONFIG_ANDROID_BOOT_IMAGE=y
Lines of this file are not shown. View the raw message.
configs/openpiton_riscv64_spl_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/phycore-am335x-r2-regor_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/phycore-am335x-r2-wega_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/px30-core-ctouch2-of10-px30_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/px30-core-ctouch2-px30_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/px30-core-edimm2.2-px30_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/roc-pc-mezzanine-rk3399_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/rock-pi-n10-rk3399pro_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sam9x60_curiosity_mmc_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d27_som1_ek_mmc1_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d27_som1_ek_qspiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d27_wlsom1_ek_mmc_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d27_wlsom1_ek_qspiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d2_icp_qspiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d2_ptc_ek_nandflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d2_xplained_emmc_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d2_xplained_qspiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d2_xplained_spiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d36ek_cmp_nandflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d36ek_cmp_spiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d3_xplained_nandflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d4_xplained_nandflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/sama5d4_xplained_spiflash_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/socfpga_stratix10_atf_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15-icore-stm32mp1-ctouch2_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15-icore-stm32mp1-edimm2.2_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15-microgea-stm32mp1-microdev2-of7_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15-microgea-stm32mp1-microdev2_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15_dhcom_basic_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/stm32mp15_dhcor_basic_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/synquacer_developerbox_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_versal_mini_emmc0_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_versal_mini_emmc1_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_zynqmp_mini_emmc0_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_zynqmp_mini_emmc1_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_zynqmp_mini_nand_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_zynqmp_mini_nand_single_defconfig +2 -0
Lines of this file are not shown. View the raw message.
configs/xilinx_zynqmp_mini_qspi_defconfig +2 -0
Lines of this file are not shown. View the raw message.
include/configs/broadcom_bcm968580xref.h +0 -1
Lines of this file are not shown. View the raw message.
include/configs/gardena-smart-gateway-at91sam.h +0 -3
Lines of this file are not shown. View the raw message.
include/configs/imx8mm_data_modul_edm_sbc.h +0 -4
Lines of this file are not shown. View the raw message.
include/configs/imx8mn_bsh_smm_s2_common.h +0 -4
Lines of this file are not shown. View the raw message.
include/configs/microchip_mpfs_icicle.h +0 -1
Lines of this file are not shown. View the raw message.
include/configs/somlabs_visionsom_6ull.h +0 -5
Lines of this file are not shown. View the raw message.
include/configs/xilinx_versal_mini_qspi.h +0 -3
Lines of this file are not shown. View the raw message.
include/configs/xilinx_zynqmp_mini_emmc.h +0 -2
Lines of this file are not shown. View the raw message.
include/configs/xilinx_zynqmp_mini_nand.h +0 -1
Lines of this file are not shown. View the raw message.
include/configs/xilinx_zynqmp_mini_qspi.h +0 -2
Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.25.1
Part of the diff is not shown here. View the raw message.
Quoted 3 lines · Tom Rini
There are no mcf5227x platforms, remove the CPU code.
Signed-off-by Tom Rini <[email protected]>
For the series, applied to u-boot/next, thanks!
Signature · 1 line
Tom