Skip to contentSkip to conversation

arm: mvebu: Use MVEBU_SPL_BOOT_DEVICE instead of SPL_BOOT_DEVICE

PATCH In review Chris Packham 4 participants 11 messages May 28, 2022 – Jun 6, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 arm: mvebu: Use MVEBU_SPL_BOOT_DEVICE instead of SPL_BOOT_DEVICE

Update the way KWB_CFG_SEC_BOOT_DEV is determined to use CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC} instead of CONFIG_SPL_BOOT_DEVICE.

---

 arch/arm/mach-mvebu/Makefile | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
arch/arm/mach-mvebu/Makefile +6 -4
index 8bd2246325ca..61eeb9c8c186 100644
@@ -65,10 +65,12 @@ KWB_REPLACE += CSK_INDEX
 KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
 
 KWB_REPLACE += SEC_BOOT_DEV
-KWB_CFG_SEC_BOOT_DEV=$(patsubst "%",%, \
-	$(if $(findstring BOOT_SPI_NOR_FLASH,$(CONFIG_SPL_BOOT_DEVICE)),0x34) \
-	$(if $(findstring BOOT_SDIO_MMC_CARD,$(CONFIG_SPL_BOOT_DEVICE)),0x31) \
-	)
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI),)
+	KWB_CFG_SEC_BOOT_DEV=0x34
+endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),)
+	KWB_CFG_SEC_BOOT_DEV=0x31
+endif
 
 KWB_REPLACE += SEC_FUSE_DUMP
 KWB_CFG_SEC_FUSE_DUMP = a38x
Signature · 1 line
2.36.1
#1 lore raw

PATCH 2/3 Convert CONFIG_FIXED_SDHCI_ALIGNED_BUFFER to Kconfig

CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when booting from MMC. All existing usages of this have the same value so make this the default and have the Kconfig option depend on SPL && MVEBU_SPL_BOOT_DEVICE_MMC.

---

 drivers/mmc/Kconfig               | 13 +++++++++++++
 include/configs/clearfog.h        |  7 -------
 include/configs/controlcenterdc.h |  7 -------
 include/configs/db-88f6820-gp.h   |  7 -------
 include/configs/helios4.h         |  7 -------
 include/configs/turris_omnia.h    |  7 -------
 scripts/config_whitelist.txt      |  1 -
 7 files changed, 13 insertions(+), 36 deletions(-)
drivers/mmc/Kconfig +13 -0
index 5e2921ce41a7..c8f9709d2d49 100644
@@ -484,6 +484,19 @@ config SPL_MMC_SDHCI_ADMA
 	  This enables support for the ADMA (Advanced DMA) defined
 	  in the SD Host Controller Standard Specification Version 3.00 in SPL.
 
+config FIXED_SDHCI_ALIGNED_BUFFER
+	hex "SDRAM address for fixed buffer"
+	depends on SPL && MVEBU_SPL_BOOT_DEVICE_MMC
+	default 0x00180000
+	help
+	  On the Marvell Armada 38x when the SPL runs it located in internal
+	  SRAM which is the L2 cache locked to memory. When the MMC buffers
+	  are located on the stack (or bss), the SDIO controller (SDHCI) can't
+	  write into this L2 cache memory.
+
+	  This specifies the address of a fixed buffer located in SDRAM that
+	  will be used for all SDHCI transfers in the SPL.
+
 config MMC_SDHCI_ASPEED
 	bool "Aspeed SDHCI controller"
 	depends on ARCH_ASPEED
include/configs/clearfog.h +0 -7
index 871e87c26d01..ec0f0e3ed115 100644
@@ -56,13 +56,6 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA)
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
include/configs/controlcenterdc.h +0 -7
index b499d7085fd4..a8534e59d9b1 100644
@@ -53,13 +53,6 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((212 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
 /*
  * Environment Configuration
  */
include/configs/db-88f6820-gp.h +0 -7
index 8dc73e8b1cc9..b4b58e0bcb8a 100644
@@ -53,13 +53,6 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
include/configs/helios4.h +0 -7
index 151ab66f4c3f..62a52e68b56a 100644
@@ -56,13 +56,6 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA)
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
include/configs/turris_omnia.h +0 -7
index 8119340b112f..112ddd3f4961 100644
@@ -36,13 +36,6 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC
-/* SPL related MMC defines */
-# ifdef CONFIG_SPL_BUILD
-#  define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-# endif
-#endif
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
scripts/config_whitelist.txt +0 -1
index cecdda678191..25962b735f27 100644
@@ -87,7 +87,6 @@ CONFIG_FDTFILE
 CONFIG_FEC_ENET_DEV
 CONFIG_FEC_FIXED_SPEED
 CONFIG_FEC_MXC_PHYADDR
-CONFIG_FIXED_SDHCI_ALIGNED_BUFFER
 CONFIG_FLASH_BR_PRELIM
 CONFIG_FLASH_CFI_LEGACY
 CONFIG_FLASH_OR_PRELIM
Signature · 1 line
2.36.1
Reviewed-by on v1 2/3
#2 lore raw

Re: [PATCH 2/3] Convert CONFIG_FIXED_SDHCI_ALIGNED_BUFFER to Kconfig

Quoted 6 lines · On Sun, 29 May 2022 11:13:17 +1200 Chris Packham <[email protected]>…

CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when booting from MMC. All existing usages of this have the same value so make this the default and have the Kconfig option depend on SPL && MVEBU_SPL_BOOT_DEVICE_MMC.

Reviewed-by on v1 2/3
#3 lore raw

Re: [PATCH 2/3] Convert CONFIG_FIXED_SDHCI_ALIGNED_BUFFER to Kconfig

In reply to Chris Packham
Quoted 6 lines · Chris Packham

CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when booting from MMC. All existing usages of this have the same value so make this the default and have the Kconfig option depend on SPL && MVEBU_SPL_BOOT_DEVICE_MMC.

Thanks,
Stefan

Quoted 130 lines

---

  drivers/mmc/Kconfig               | 13 +++++++++++++
  include/configs/clearfog.h        |  7 -------
  include/configs/controlcenterdc.h |  7 -------
  include/configs/db-88f6820-gp.h   |  7 -------
  include/configs/helios4.h         |  7 -------
  include/configs/turris_omnia.h    |  7 -------
  scripts/config_whitelist.txt      |  1 -
  7 files changed, 13 insertions(+), 36 deletions(-)
drivers/mmc/Kconfig +13 -0
index 5e2921ce41a7..c8f9709d2d49 100644
@@ -484,6 +484,19 @@ config SPL_MMC_SDHCI_ADMA
  	  This enables support for the ADMA (Advanced DMA) defined
  	  in the SD Host Controller Standard Specification Version 3.00 in SPL.
 
+config FIXED_SDHCI_ALIGNED_BUFFER
+	hex "SDRAM address for fixed buffer"
+	depends on SPL && MVEBU_SPL_BOOT_DEVICE_MMC
+	default 0x00180000
+	help
+	  On the Marvell Armada 38x when the SPL runs it located in internal
+	  SRAM which is the L2 cache locked to memory. When the MMC buffers
+	  are located on the stack (or bss), the SDIO controller (SDHCI) can't
+	  write into this L2 cache memory.
+
+	  This specifies the address of a fixed buffer located in SDRAM that
+	  will be used for all SDHCI transfers in the SPL.
+
  config MMC_SDHCI_ASPEED
  	bool "Aspeed SDHCI controller"
  	depends on ARCH_ASPEED
include/configs/clearfog.h +0 -7
index 871e87c26d01..ec0f0e3ed115 100644
@@ -56,13 +56,6 @@
  #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
  #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA)
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
  /*
   * mv-common.h should be defined after CMD configs since it used them
   * to enable certain macros
include/configs/controlcenterdc.h +0 -7
index b499d7085fd4..a8534e59d9b1 100644
@@ -53,13 +53,6 @@
  #define CONFIG_SPL_STACK		(0x40000000 + ((212 - 16) << 10))
  #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
  /*
   * Environment Configuration
   */
include/configs/db-88f6820-gp.h +0 -7
index 8dc73e8b1cc9..b4b58e0bcb8a 100644
@@ -53,13 +53,6 @@
  #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
  #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
  /*
   * mv-common.h should be defined after CMD configs since it used them
   * to enable certain macros
include/configs/helios4.h +0 -7
index 151ab66f4c3f..62a52e68b56a 100644
@@ -56,13 +56,6 @@
  #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
  #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA)
-/* SPL related MMC defines */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
  /*
   * mv-common.h should be defined after CMD configs since it used them
   * to enable certain macros
include/configs/turris_omnia.h +0 -7
index 8119340b112f..112ddd3f4961 100644
@@ -36,13 +36,6 @@
  #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
  #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC
-/* SPL related MMC defines */
-# ifdef CONFIG_SPL_BUILD
-#  define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-# endif
-#endif
-
  /*
   * mv-common.h should be defined after CMD configs since it used them
   * to enable certain macros
scripts/config_whitelist.txt +0 -0
index cecdda678191..25962b735f27 100644

scripts/config_whitelist.txt CONFIG_FDTFILE · line 92

Quoted 7 lines
scripts/config_whitelist.txt +0 -1
@@ -87,7 +87,6 @@ CONFIG_FDTFILE
  CONFIG_FEC_ENET_DEV
  CONFIG_FEC_FIXED_SPEED
  CONFIG_FEC_MXC_PHYADDR
-CONFIG_FIXED_SDHCI_ALIGNED_BUFFER
  CONFIG_FLASH_BR_PRELIM
  CONFIG_FLASH_CFI_LEGACY
  CONFIG_FLASH_OR_PRELIM

Viele Grüße,
Stefan Roese

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
#4 lore raw

Re: [PATCH 2/3] Convert CONFIG_FIXED_SDHCI_ALIGNED_BUFFER to Kconfig

In reply to Chris Packham
Quoted 8 lines · Chris Packham

CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when booting from MMC. All existing usages of this have the same value so make this the default and have the Kconfig option depend on SPL && MVEBU_SPL_BOOT_DEVICE_MMC.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom
#5 lore raw

PATCH 3/3 arm: mvebu: Remove CONFIG_SPL_BOOT_DEVICE

In reply to Chris Packham

CONFIG_SPL_BOOT_DEVICE was made obsolete by CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}. CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of CONFIG_SPL_BOOT_DEVICE can simply have the option removed.

---

 include/configs/controlcenterdc.h | 11 -----------
 include/configs/db-88f6820-amc.h  | 12 ------------
 include/configs/db-88f6820-gp.h   | 11 -----------
 scripts/config_whitelist.txt      |  1 -
 4 files changed, 35 deletions(-)
include/configs/controlcenterdc.h +0 -11
index a8534e59d9b1..3d7da4b2a33e 100644
@@ -23,17 +23,6 @@
 #endif
 
 /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define SPL_BOOT_SDIO_MMC_CARD		2
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
 /* Defines for SPL */
 #define CONFIG_SPL_SIZE			(160 << 10)
 
include/configs/db-88f6820-amc.h +0 -12
index 6538e66052aa..d044292d6b5a 100644
@@ -27,18 +27,6 @@
 	"initrd_high=0x10000000\0"
 
 /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- *
- * MMC is not populated on this board.
- * NAND support may be added in the future.
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
 /* Defines for SPL */
 #define CONFIG_SPL_SIZE			(140 << 10)
 #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - (CONFIG_SPL_TEXT_BASE - 0x40000000))
include/configs/db-88f6820-gp.h +0 -11
index b4b58e0bcb8a..35ff6a876fde 100644
@@ -28,17 +28,6 @@
 	"initrd_high=0x10000000\0"
 
 /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define SPL_BOOT_SDIO_MMC_CARD		2
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
 /* Defines for SPL */
 #define CONFIG_SPL_SIZE			(140 << 10)
 #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - (CONFIG_SPL_TEXT_BASE - 0x40000000))
scripts/config_whitelist.txt +0 -1
index 25962b735f27..a8766c9755ab 100644
@@ -565,7 +565,6 @@ CONFIG_SPI_HALF_DUPLEX
 CONFIG_SPI_N25Q256A_RESET
 CONFIG_SPL_BOARD_LOAD_IMAGE
 CONFIG_SPL_BOOTROM_SAVE
-CONFIG_SPL_BOOT_DEVICE
 CONFIG_SPL_BSS_MAX_SIZE
 CONFIG_SPL_BSS_START_ADDR
 CONFIG_SPL_CMT
Signature · 1 line
2.36.1
Reviewed-by on v1 3/3
#6 lore raw

Re: [PATCH 3/3] arm: mvebu: Remove CONFIG_SPL_BOOT_DEVICE

Quoted 6 lines · On Sun, 29 May 2022 11:13:18 +1200 Chris Packham <[email protected]>…

CONFIG_SPL_BOOT_DEVICE was made obsolete by CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}. CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of CONFIG_SPL_BOOT_DEVICE can simply have the option removed.

Reviewed-by on v1 3/3
#7 lore raw

Re: [PATCH 3/3] arm: mvebu: Remove CONFIG_SPL_BOOT_DEVICE

In reply to Chris Packham
Quoted 6 lines · Chris Packham

CONFIG_SPL_BOOT_DEVICE was made obsolete by CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}. CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of CONFIG_SPL_BOOT_DEVICE can simply have the option removed.

Thanks,
Stefan

Quoted 80 lines

---

  include/configs/controlcenterdc.h | 11 -----------
  include/configs/db-88f6820-amc.h  | 12 ------------
  include/configs/db-88f6820-gp.h   | 11 -----------
  scripts/config_whitelist.txt      |  1 -
  4 files changed, 35 deletions(-)
include/configs/controlcenterdc.h +0 -11
index a8534e59d9b1..3d7da4b2a33e 100644
@@ -23,17 +23,6 @@
  #endif
 
  /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define SPL_BOOT_SDIO_MMC_CARD		2
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
  /* Defines for SPL */
  #define CONFIG_SPL_SIZE			(160 << 10)
 
include/configs/db-88f6820-amc.h +0 -12
index 6538e66052aa..d044292d6b5a 100644
@@ -27,18 +27,6 @@
  	"initrd_high=0x10000000\0"
 
  /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- *
- * MMC is not populated on this board.
- * NAND support may be added in the future.
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
  /* Defines for SPL */
  #define CONFIG_SPL_SIZE			(140 << 10)
  #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - (CONFIG_SPL_TEXT_BASE - 0x40000000))
include/configs/db-88f6820-gp.h +0 -11
index b4b58e0bcb8a..35ff6a876fde 100644
@@ -28,17 +28,6 @@
  	"initrd_high=0x10000000\0"
 
  /* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define SPL_BOOT_SDIO_MMC_CARD		2
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
  /* Defines for SPL */
  #define CONFIG_SPL_SIZE			(140 << 10)
  #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - (CONFIG_SPL_TEXT_BASE - 0x40000000))
scripts/config_whitelist.txt +0 -0
index 25962b735f27..a8766c9755ab 100644

scripts/config_whitelist.txt CONFIG_SPI_HALF_DUPLEX · line 570

Quoted 7 lines
scripts/config_whitelist.txt +0 -1
@@ -565,7 +565,6 @@ CONFIG_SPI_HALF_DUPLEX
  CONFIG_SPI_N25Q256A_RESET
  CONFIG_SPL_BOARD_LOAD_IMAGE
  CONFIG_SPL_BOOTROM_SAVE
-CONFIG_SPL_BOOT_DEVICE
  CONFIG_SPL_BSS_MAX_SIZE
  CONFIG_SPL_BSS_START_ADDR
  CONFIG_SPL_CMT

Viele Grüße,
Stefan Roese

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
#8 lore raw

Re: [PATCH 3/3] arm: mvebu: Remove CONFIG_SPL_BOOT_DEVICE

In reply to Chris Packham
Quoted 8 lines · Chris Packham

CONFIG_SPL_BOOT_DEVICE was made obsolete by CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}. CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of CONFIG_SPL_BOOT_DEVICE can simply have the option removed.

Applied to u-boot/next, thanks!

Signature · 1 line
Tom
Reviewed-by on v1 1/3
#9 lore raw
In reply to Chris Packham
Quoted 5 lines · Chris Packham

Update the way KWB_CFG_SEC_BOOT_DEV is determined to use CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC} instead of CONFIG_SPL_BOOT_DEVICE.

Thanks,
Stefan

Quoted 16 lines

---

  arch/arm/mach-mvebu/Makefile | 10 ++++++----
  1 file changed, 6 insertions(+), 4 deletions(-)
arch/arm/mach-mvebu/Makefile +0 -3
index 8bd2246325ca..61eeb9c8c186 100644
@@ -65,10 +65,12 @@ KWB_REPLACE += CSK_INDEX
  KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
 
  KWB_REPLACE += SEC_BOOT_DEV
-KWB_CFG_SEC_BOOT_DEV=$(patsubst "%",%, \
-	$(if $(findstring BOOT_SPI_NOR_FLASH,$(CONFIG_SPL_BOOT_DEVICE)),0x34) \
-	$(if $(findstring BOOT_SDIO_MMC_CARD,$(CONFIG_SPL_BOOT_DEVICE)),0x31) \

arch/arm/mach-mvebu/Makefile KWB_REPLACE += CSK_INDEX · line 76

Quoted 10 lines
arch/arm/mach-mvebu/Makefile +6 -1
-	)
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI),)
+	KWB_CFG_SEC_BOOT_DEV=0x34
+endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),)
+	KWB_CFG_SEC_BOOT_DEV=0x31
+endif
 
  KWB_REPLACE += SEC_FUSE_DUMP
  KWB_CFG_SEC_FUSE_DUMP = a38x

Viele Grüße,
Stefan Roese

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]