Skip to contentSkip to conversation

iommu/vt-d: Add RPLS to quirk list to skip TE disabling

PATCH In review Sasha Levin 5 participants 142 messages May 30, 2022 – Jun 6, 2022

Subsystems (38)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/135 iommu/vt-d: Add RPLS to quirk list to skip TE disabling

From: Tejas Upadhyay <[email protected]>

[ Upstream commit 0a967f5bfd9134b89681cae58deb222e20840e76 ]

The VT-d spec requires (10.4.4 Global Command Register, TE field) that:

Hardware implementations supporting DMA draining must drain any in-flight DMA read/write requests queued within the Root-Complex before completing the translation enable command and reflecting the status of the command through the TES field in the Global Status register.

Unfortunately, some integrated graphic devices fail to do so after some kind of power state transition. As the result, the system might stuck in iommu_disable_translati on(), waiting for the completion of TE transition.

This adds RPLS to a quirk list for those devices and skips TE disabling if the qurik hits.

---
 drivers/iommu/intel/iommu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/iommu/intel/iommu.c +1 -1
index ab2273300346..e3f15e0cae34 100644
@@ -5764,7 +5764,7 @@ static void quirk_igfx_skip_te_disable(struct pci_dev *dev)
 	ver = (dev->device >> 8) & 0xff;
 	if (ver != 0x45 && ver != 0x46 && ver != 0x4c &&
 	    ver != 0x4e && ver != 0x8a && ver != 0x98 &&
-	    ver != 0x9a)
+	    ver != 0x9a && ver != 0xa7)
 		return;
 
 	if (risky_device(dev))
Signature · 6 lines
2.35.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#1 lore raw

PATCH 2/135 drm/vmwgfx: validate the screen formats

From: Zack Rusin <[email protected]>

[ Upstream commit 8bb75aeb58bd688d70827ae179bd3da57b6d975b ]

The kms code wasn't validating the modifiers and was letting through unsupported formats. rgb8 was never properly supported and has no matching svga screen target format so remove it.
This fixes format/modifier failures in kms_addfb_basic from IGT.

---
 drivers/gpu/drm/vmwgfx/vmwgfx_kms.c | 30 +++++++++++++++--------------
 drivers/gpu/drm/vmwgfx/vmwgfx_kms.h |  1 -
 2 files changed, 16 insertions(+), 15 deletions(-)
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c +16 -14
index 93431e8f6606..9410152f9d6f 100644
@@ -914,6 +914,15 @@ static int vmw_kms_new_framebuffer_surface(struct vmw_private *dev_priv,
 	 * Sanity checks.
 	 */
 
+	if (!drm_any_plane_has_format(&dev_priv->drm,
+				      mode_cmd->pixel_format,
+				      mode_cmd->modifier[0])) {
+		drm_dbg(&dev_priv->drm,
+			"unsupported pixel format %p4cc / modifier 0x%llx\n",
+			&mode_cmd->pixel_format, mode_cmd->modifier[0]);
+		return -EINVAL;
+	}
+
 	/* Surface must be marked as a scanout. */
 	if (unlikely(!surface->metadata.scanout))
 		return -EINVAL;
@@ -1236,20 +1245,13 @@ static int vmw_kms_new_framebuffer_bo(struct vmw_private *dev_priv,
 		return -EINVAL;
 	}
 
-	/* Limited framebuffer color depth support for screen objects */
-	if (dev_priv->active_display_unit == vmw_du_screen_object) {
-		switch (mode_cmd->pixel_format) {
-		case DRM_FORMAT_XRGB8888:
-		case DRM_FORMAT_ARGB8888:
-			break;
-		case DRM_FORMAT_XRGB1555:
-		case DRM_FORMAT_RGB565:
-			break;
-		default:
-			DRM_ERROR("Invalid pixel format: %p4cc\n",
-				  &mode_cmd->pixel_format);
-			return -EINVAL;
-		}
+	if (!drm_any_plane_has_format(&dev_priv->drm,
+				      mode_cmd->pixel_format,
+				      mode_cmd->modifier[0])) {
+		drm_dbg(&dev_priv->drm,
+			"unsupported pixel format %p4cc / modifier 0x%llx\n",
+			&mode_cmd->pixel_format, mode_cmd->modifier[0]);
+		return -EINVAL;
 	}
 
 	vfbd = kzalloc(sizeof(*vfbd), GFP_KERNEL);
drivers/gpu/drm/vmwgfx/vmwgfx_kms.h +0 -1
index 4d36e8507380..d9ebd02099a6 100644
@@ -247,7 +247,6 @@ struct vmw_framebuffer_bo {
 static const uint32_t __maybe_unused vmw_primary_plane_formats[] = {
 	DRM_FORMAT_XRGB1555,
 	DRM_FORMAT_RGB565,
-	DRM_FORMAT_RGB888,
 	DRM_FORMAT_XRGB8888,
 	DRM_FORMAT_ARGB8888,
 };
Signature · 1 line
2.35.1
author maintainer
#2 lore raw

PATCH 3/135 ath11k: fix the warning of dev_wake in mhi_pm_disable_transition()

In reply to Sasha Levin

From: Wen Gong <[email protected]>

[ Upstream commit 0d7a8a6204ea9271f1d0a8c66a9fd2f54d2e3cbc ]

When test device recovery with below command, it has warning in message as below.
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash

warning message:

[ 1965.642121] ath11k_pci 0000:06:00.0: simulating firmware assert crash
[ 1968.471364] ieee80211 phy0: Hardware restart was requested
[ 1968.511305] ------------[ cut here ]------------
[ 1968.511368] WARNING: CPU: 3 PID: 1546 at drivers/bus/mhi/core/pm.c:505 mhi_pm_disable_transition+0xb37/0xda0 [mhi]
[ 1968.511443] Modules linked in: ath11k_pci ath11k mac80211 libarc4 cfg80211 qmi_helpers qrtr_mhi mhi qrtr nvme nvme_core
[ 1968.511563] CPU: 3 PID: 1546 Comm: kworker/u17:0 Kdump: loaded Tainted: G        W         5.17.0-rc3-wt-ath+ #579
[ 1968.511629] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021
[ 1968.511704] Workqueue: mhi_hiprio_wq mhi_pm_st_worker [mhi]
[ 1968.511787] RIP: 0010:mhi_pm_disable_transition+0xb37/0xda0 [mhi]
[ 1968.511870] Code: a9 fe ff ff 4c 89 ff 44 89 04 24 e8 03 46 f6 e5 44 8b 04 24 41 83 f8 01 0f 84 21 fe ff ff e9 4c fd ff ff 0f 0b e9 af f8 ff ff <0f> 0b e9 5c f8 ff ff 48 89 df e8 da 9e ee e3 e9 12 fd ff ff 4c 89
[ 1968.511923] RSP: 0018:ffffc900024efbf0 EFLAGS: 00010286
[ 1968.511969] RAX: 00000000ffffffff RBX: ffff88811d241250 RCX: ffffffffc0176922
[ 1968.512014] RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffff888118a90a24
[ 1968.512059] RBP: ffff888118a90800 R08: 0000000000000000 R09: ffff888118a90a27
[ 1968.512102] R10: ffffed1023152144 R11: 0000000000000001 R12: ffff888118a908ac
[ 1968.512229] R13: ffff888118a90928 R14: dffffc0000000000 R15: ffff888118a90a24
[ 1968.512310] FS:  0000000000000000(0000) GS:ffff888234200000(0000) knlGS:0000000000000000
[ 1968.512405] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1968.512493] CR2: 00007f5538f443a8 CR3: 000000016dc28001 CR4: 00000000003706e0
[ 1968.512587] Call Trace:
[ 1968.512672]  <TASK>
[ 1968.512751]  ? _raw_spin_unlock_irq+0x1f/0x40
[ 1968.512859]  mhi_pm_st_worker+0x3ac/0x790 [mhi]
[ 1968.512959]  ? mhi_pm_mission_mode_transition.isra.0+0x7d0/0x7d0 [mhi]
[ 1968.513063]  process_one_work+0x86a/0x1400
[ 1968.513184]  ? pwq_dec_nr_in_flight+0x230/0x230
[ 1968.513312]  ? move_linked_works+0x125/0x290
[ 1968.513416]  worker_thread+0x6db/0xf60
[ 1968.513536]  ? process_one_work+0x1400/0x1400
[ 1968.513627]  kthread+0x241/0x2d0
[ 1968.513733]  ? kthread_complete_and_exit+0x20/0x20
[ 1968.513821]  ret_from_fork+0x22/0x30
[ 1968.513924]  </TASK>

Reason is mhi_deassert_dev_wake() from mhi_device_put() is called but mhi_assert_dev_wake() from __mhi_device_get_sync() is not called in progress of recovery. Commit 8e0559921f9a ("bus: mhi: core:
Skip device wake in error or shutdown state") add check for the pm_state of mhi in __mhi_device_get_sync(), and the pm_state is not the normal state untill recovery is completed, so it leads the dev_wake is not 0 and above warning print in mhi_pm_disable_transition() while checking mhi_cntrl->dev_wake.

Add check in ath11k_pci_write32()/ath11k_pci_read32() to skip call mhi_device_put() if mhi_device_get_sync() does not really do wake, then the warning gone.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

---
 drivers/net/wireless/ath/ath11k/pci.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath11k/pci.c +8 -4
index 903758751c99..8a3ff12057e8 100644
@@ -191,6 +191,7 @@ void ath11k_pci_write32(struct ath11k_base *ab, u32 offset, u32 value)
 {
 	struct ath11k_pci *ab_pci = ath11k_pci_priv(ab);
 	u32 window_start;
+	int ret = 0;
 
 	/* for offset beyond BAR + 4K - 32, may
 	 * need to wakeup MHI to access.
@@ -198,7 +199,7 @@ void ath11k_pci_write32(struct ath11k_base *ab, u32 offset, u32 value)
 	if (ab->hw_params.wakeup_mhi &&
 	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
-		mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
+		ret = mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
 
 	if (offset < WINDOW_START) {
 		iowrite32(value, ab->mem  + offset);
@@ -222,7 +223,8 @@ void ath11k_pci_write32(struct ath11k_base *ab, u32 offset, u32 value)
 
 	if (ab->hw_params.wakeup_mhi &&
 	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
-	    offset >= ACCESS_ALWAYS_OFF)
+	    offset >= ACCESS_ALWAYS_OFF &&
+	    !ret)
 		mhi_device_put(ab_pci->mhi_ctrl->mhi_dev);
 }
 
@@ -230,6 +232,7 @@ u32 ath11k_pci_read32(struct ath11k_base *ab, u32 offset)
 {
 	struct ath11k_pci *ab_pci = ath11k_pci_priv(ab);
 	u32 val, window_start;
+	int ret = 0;
 
 	/* for offset beyond BAR + 4K - 32, may
 	 * need to wakeup MHI to access.
@@ -237,7 +240,7 @@ u32 ath11k_pci_read32(struct ath11k_base *ab, u32 offset)
 	if (ab->hw_params.wakeup_mhi &&
 	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
 	    offset >= ACCESS_ALWAYS_OFF)
-		mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
+		ret = mhi_device_get_sync(ab_pci->mhi_ctrl->mhi_dev);
 
 	if (offset < WINDOW_START) {
 		val = ioread32(ab->mem + offset);
@@ -261,7 +264,8 @@ u32 ath11k_pci_read32(struct ath11k_base *ab, u32 offset)
 
 	if (ab->hw_params.wakeup_mhi &&
 	    test_bit(ATH11K_PCI_FLAG_INIT_DONE, &ab_pci->flags) &&
-	    offset >= ACCESS_ALWAYS_OFF)
+	    offset >= ACCESS_ALWAYS_OFF &&
+	    !ret)
 		mhi_device_put(ab_pci->mhi_ctrl->mhi_dev);
 
 	return val;
Signature · 7 lines
2.35.1


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
author maintainer
#3 lore raw

PATCH 4/135 drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes

In reply to Sasha Levin

From: Liu Zixian <[email protected]>

[ Upstream commit 194d250cdc4a40ccbd179afd522a9e9846957402 ]

drm_cvt_mode may return NULL and we should check it.

This bug is found by syzkaller:

FAULT_INJECTION stacktrace:

[  168.567394] FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 1
[  168.567403] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1
[  168.567406] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[  168.567408] Call trace:
[  168.567414]  dump_backtrace+0x0/0x310
[  168.567418]  show_stack+0x28/0x38
[  168.567423]  dump_stack+0xec/0x15c
[  168.567427]  should_fail+0x3ac/0x3d0
[  168.567437]  __should_failslab+0xb8/0x120
[  168.567441]  should_failslab+0x28/0xc0
[  168.567445]  kmem_cache_alloc_trace+0x50/0x640
[  168.567454]  drm_mode_create+0x40/0x90
[  168.567458]  drm_cvt_mode+0x48/0xc78
[  168.567477]  virtio_gpu_conn_get_modes+0xa8/0x140 [virtio_gpu]
[  168.567485]  drm_helper_probe_single_connector_modes+0x3a4/0xd80
[  168.567492]  drm_mode_getconnector+0x2e0/0xa70
[  168.567496]  drm_ioctl_kernel+0x11c/0x1d8
[  168.567514]  drm_ioctl+0x558/0x6d0
[  168.567522]  do_vfs_ioctl+0x160/0xf30
[  168.567525]  ksys_ioctl+0x98/0xd8
[  168.567530]  __arm64_sys_ioctl+0x50/0xc8
[  168.567536]  el0_svc_common+0xc8/0x320
[  168.567540]  el0_svc_handler+0xf8/0x160
[  168.567544]  el0_svc+0x10/0x218

KASAN stacktrace:

[  168.567561] BUG: KASAN: null-ptr-deref in virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu]
[  168.567565] Read of size 4 at addr 0000000000000054 by task syz/6425
[  168.567566]
[  168.567571] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1
[  168.567573] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[  168.567575] Call trace:
[  168.567578]  dump_backtrace+0x0/0x310
[  168.567582]  show_stack+0x28/0x38
[  168.567586]  dump_stack+0xec/0x15c
[  168.567591]  kasan_report+0x244/0x2f0
[  168.567594]  __asan_load4+0x58/0xb0
[  168.567607]  virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu]
[  168.567612]  drm_helper_probe_single_connector_modes+0x3a4/0xd80
[  168.567617]  drm_mode_getconnector+0x2e0/0xa70
[  168.567621]  drm_ioctl_kernel+0x11c/0x1d8
[  168.567624]  drm_ioctl+0x558/0x6d0
[  168.567628]  do_vfs_ioctl+0x160/0xf30
[  168.567632]  ksys_ioctl+0x98/0xd8
[  168.567636]  __arm64_sys_ioctl+0x50/0xc8
[  168.567641]  el0_svc_common+0xc8/0x320
[  168.567645]  el0_svc_handler+0xf8/0x160
[  168.567649]  el0_svc+0x10/0x218
---
 drivers/gpu/drm/virtio/virtgpu_display.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/virtio/virtgpu_display.c +2 -0
index 5b00310ac4cd..f73352e7b832 100644
@@ -179,6 +179,8 @@ static int virtio_gpu_conn_get_modes(struct drm_connector *connector)
 		DRM_DEBUG("add mode: %dx%d\n", width, height);
 		mode = drm_cvt_mode(connector->dev, width, height, 60,
 				    false, false, false);
+		if (!mode)
+			return count;
 		mode->type |= DRM_MODE_TYPE_PREFERRED;
 		drm_mode_probed_add(connector, mode);
 		count++;
Signature · 6 lines
2.35.1

_______________________________________________
Virtualization mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/virtualization
author maintainer
#4 lore raw

PATCH 5/135 selftests/bpf: Fix vfs_link kprobe definition

In reply to Sasha Levin

From: Nikolay Borisov <[email protected]>

[ Upstream commit e299bcd4d16ff86f46c48df1062c8aae0eca1ed8 ]

Since commit 6521f8917082 ("namei: prepare for idmapped mounts") vfs_link's prototype was changed, the kprobe definition in profiler selftest in turn wasn't updated. The result is that all argument after the first are now stored in different registers. This means that self-test has been broken ever since. Fix it by updating the kprobe definition accordingly.

---
 tools/testing/selftests/bpf/progs/profiler.inc.h | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
tools/testing/selftests/bpf/progs/profiler.inc.h +3 -2
index 4896fdf816f7..92331053dba3 100644
@@ -826,8 +826,9 @@ int kprobe_ret__do_filp_open(struct pt_regs* ctx)
 
 SEC("kprobe/vfs_link")
 int BPF_KPROBE(kprobe__vfs_link,
-	       struct dentry* old_dentry, struct inode* dir,
-	       struct dentry* new_dentry, struct inode** delegated_inode)
+	       struct dentry* old_dentry, struct user_namespace *mnt_userns,
+	       struct inode* dir, struct dentry* new_dentry,
+	       struct inode** delegated_inode)
 {
 	struct bpf_func_stats_ctx stats_ctx;
 	bpf_stats_enter(&stats_ctx, profiler_bpf_vfs_link);
Signature · 1 line
2.35.1
author maintainer
#5 lore raw

PATCH 6/135 selftests/bpf: Fix parsing of prog types in UAPI hdr for bpftool sync

In reply to Sasha Levin

From: Quentin Monnet <[email protected]>

[ Upstream commit 4eeebce6ac4ad80ee8243bb847c98e0e55848d47 ]

The script for checking that various lists of types in bpftool remain in sync with the UAPI BPF header uses a regex to parse enum bpf_prog_type. If this enum contains a set of values different from the list of program types in bpftool, it complains.

This script should have reported the addition, some time ago, of the new BPF_PROG_TYPE_SYSCALL, which was not reported to bpftool's program types list. It failed to do so, because it failed to parse that new type from the enum. This is because the new value, in the BPF header, has an explicative comment on the same line, and the regex does not support that.

Let's update the script to support parsing enum values when they have comments on the same line.

---
 tools/testing/selftests/bpf/test_bpftool_synctypes.py | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/bpf/test_bpftool_synctypes.py +1 -1
index 6bf21e47882a..c0e7acd698ed 100755
@@ -180,7 +180,7 @@ class FileExtractor(object):
         @enum_name: name of the enum to parse
         """
         start_marker = re.compile(f'enum {enum_name} {{\n')
-        pattern = re.compile('^\s*(BPF_\w+),?$')
+        pattern = re.compile('^\s*(BPF_\w+),?(\s+/\*.*\*/)?$')
         end_marker = re.compile('^};')
         parser = BlockParser(self.reader)
         parser.search_block(start_marker)
Signature · 1 line
2.35.1
author maintainer
#6 lore raw

PATCH 7/135 ath11k: Change max no of active probe SSID and BSSID to fw capability

In reply to Sasha Levin

From: Karthikeyan Kathirvel <[email protected]>

[ Upstream commit 50dc9ce9f80554a88e33b73c30851acf2be36ed3 ]

The maximum number of SSIDs in a for active probe requests is currently reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver. The scan_req_params structure only has the capacity to hold 10 SSIDs. This leads to a buffer overflow which can be triggered from wpa_supplicant in userspace. When copying the SSIDs into the scan_req_params structure in the ath11k_mac_op_hw_scan route, it can overwrite the extraie pointer.

Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe request will be sent, so totally 64 probe requests supported. So set both max ssid and bssid to 16 and 4 respectively. Remove the redundant macros of ssid and bssid.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1

---
 drivers/net/wireless/ath/ath11k/wmi.h | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)
drivers/net/wireless/ath/ath11k/wmi.h +2 -10
index 2f26ec1a8aa3..8173570975e4 100644
@@ -3087,9 +3087,6 @@ enum scan_dwelltime_adaptive_mode {
 	SCAN_DWELL_MODE_STATIC = 4
 };
 
-#define WLAN_SCAN_MAX_NUM_SSID          10
-#define WLAN_SCAN_MAX_NUM_BSSID         10
-
 #define WLAN_SSID_MAX_LEN 32
 
 struct element_info {
@@ -3104,7 +3101,6 @@ struct wlan_ssid {
 
 #define WMI_IE_BITMAP_SIZE             8
 
-#define WMI_SCAN_MAX_NUM_SSID                0x0A
 /* prefix used by scan requestor ids on the host */
 #define WMI_HOST_SCAN_REQUESTOR_ID_PREFIX 0xA000
 
@@ -3112,10 +3108,6 @@ struct wlan_ssid {
 /* host cycles through the lower 12 bits to generate ids */
 #define WMI_HOST_SCAN_REQ_ID_PREFIX 0xA000
 
-#define WLAN_SCAN_PARAMS_MAX_SSID    16
-#define WLAN_SCAN_PARAMS_MAX_BSSID   4
-#define WLAN_SCAN_PARAMS_MAX_IE_LEN  256
-
 /* Values lower than this may be refused by some firmware revisions with a scan
  * completion with a timedout reason.
  */
@@ -3311,8 +3303,8 @@ struct scan_req_params {
 	u32 n_probes;
 	u32 *chan_list;
 	u32 notify_scan_events;
-	struct wlan_ssid ssid[WLAN_SCAN_MAX_NUM_SSID];
-	struct wmi_mac_addr bssid_list[WLAN_SCAN_MAX_NUM_BSSID];
+	struct wlan_ssid ssid[WLAN_SCAN_PARAMS_MAX_SSID];
+	struct wmi_mac_addr bssid_list[WLAN_SCAN_PARAMS_MAX_BSSID];
 	struct element_info extraie;
 	struct element_info htcap;
 	struct element_info vhtcap;
Signature · 7 lines
2.35.1


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
author maintainer
#7 lore raw

PATCH 8/135 mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queue

In reply to Sasha Levin

From: Niels Dossche <[email protected]>

[ Upstream commit 3e12968f6d12a34b540c39cbd696a760cc4616f0 ]

cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx) is held during the function's execution. mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not hold that lock, therefore violating the assertion.
Add a lock around the call.

Disclaimer:
I am currently working on a static analyser to detect missing locks. This was a reported case. I manually verified the report by looking at the code, so that I do not send wrong information or patches. After concluding that this seems to be a true positive, I created this patch.
However, as I do not in fact have this particular hardware, I was unable to test it.

---
 drivers/net/wireless/marvell/mwifiex/11h.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/net/wireless/marvell/mwifiex/11h.c +2 -0
index d2ee6469e67b..3fa25cd64cda 100644
@@ -303,5 +303,7 @@ void mwifiex_dfs_chan_sw_work_queue(struct work_struct *work)
 
 	mwifiex_dbg(priv->adapter, MSG,
 		    "indicating channel switch completion to kernel\n");
+	mutex_lock(&priv->wdev.mtx);
 	cfg80211_ch_switch_notify(priv->netdev, &priv->dfs_chandef);
+	mutex_unlock(&priv->wdev.mtx);
 }
Signature · 1 line
2.35.1
author maintainer
#8 lore raw

PATCH 9/135 b43legacy: Fix assigning negative value to unsigned variable

In reply to Sasha Levin

From: Haowen Bai <[email protected]>

[ Upstream commit 3f6b867559b3d43a7ce1b4799b755e812fc0d503 ]

fix warning reported by smatch:
drivers/net/wireless/broadcom/b43legacy/phy.c:1181 b43legacy_phy_lo_b_measure()
warn: assigning (-772) to unsigned variable 'fval'

---
 drivers/net/wireless/broadcom/b43legacy/phy.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/broadcom/b43legacy/phy.c +1 -1
index 05404fbd1e70..c1395e622759 100644
@@ -1123,7 +1123,7 @@ void b43legacy_phy_lo_b_measure(struct b43legacy_wldev *dev)
 	struct b43legacy_phy *phy = &dev->phy;
 	u16 regstack[12] = { 0 };
 	u16 mls;
-	u16 fval;
+	s16 fval;
 	int i;
 	int j;
 
Signature · 7 lines
2.35.1


_______________________________________________
b43-dev mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/b43-dev
author maintainer
#9 lore raw

PATCH 10/135 b43: Fix assigning negative value to unsigned variable

In reply to Sasha Levin

From: Haowen Bai <[email protected]>

[ Upstream commit 11800d893b38e0e12d636c170c1abc19c43c730c ]

fix warning reported by smatch:
drivers/net/wireless/broadcom/b43/phy_n.c:585 b43_nphy_adjust_lna_gain_table()
warn: assigning (-2) to unsigned variable '*(lna_gain[0])'

---
 drivers/net/wireless/broadcom/b43/phy_n.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/broadcom/b43/phy_n.c +1 -1
index cf3ccf4ddfe7..aa5c99465674 100644
@@ -582,7 +582,7 @@ static void b43_nphy_adjust_lna_gain_table(struct b43_wldev *dev)
 	u16 data[4];
 	s16 gain[2];
 	u16 minmax[2];
-	static const u16 lna_gain[4] = { -2, 10, 19, 25 };
+	static const s16 lna_gain[4] = { -2, 10, 19, 25 };
 
 	if (nphy->hang_avoid)
 		b43_nphy_stay_in_carrier_search(dev, 1);
Signature · 7 lines
2.35.1


_______________________________________________
b43-dev mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/b43-dev
author maintainer
#10 lore raw

PATCH 11/135 ipw2x00: Fix potential NULL dereference in libipw_xmit()

In reply to Sasha Levin

From: Haowen Bai <[email protected]>

[ Upstream commit e8366bbabe1d207cf7c5b11ae50e223ae6fc278b ]

crypt and crypt->ops could be null, so we need to checking null before dereference

---
 drivers/net/wireless/intel/ipw2x00/libipw_tx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/intel/ipw2x00/libipw_tx.c +1 -1
index 36d1e6b2568d..4aec1fce1ae2 100644
@@ -383,7 +383,7 @@ netdev_tx_t libipw_xmit(struct sk_buff *skb, struct net_device *dev)
 
 		/* Each fragment may need to have room for encryption
 		 * pre/postfix */
-		if (host_encrypt)
+		if (host_encrypt && crypt && crypt->ops)
 			bytes_per_frag -= crypt->ops->extra_mpdu_prefix_len +
 			    crypt->ops->extra_mpdu_postfix_len;
 
Signature · 1 line
2.35.1
author maintainer
#11 lore raw

PATCH 12/135 ipv6: fix locking issues with loops over idev->addr_list

In reply to Sasha Levin

From: Niels Dossche <[email protected]>

[ Upstream commit 51454ea42c1ab4e0c2828bb0d4d53957976980de ]

idev->addr_list needs to be protected by idev->lock. However, it is not always possible to do so while iterating and performing actions on inet6_ifaddr instances. For example, multiple functions (like addrconf_{join,leave}_anycast) eventually call down to other functions that acquire the idev->lock. The current code temporarily unlocked the idev->lock during the loops, which can cause race conditions. Moving the locks up is also not an appropriate solution as the ordering of lock acquisition will be inconsistent with for example mc_lock.

This solution adds an additional field to inet6_ifaddr that is used to temporarily add the instances to a temporary list while holding idev->lock. The temporary list can then be traversed without holding idev->lock. This change was done in two places. In addrconf_ifdown, the list_for_each_entry_safe variant of the list loop is also no longer necessary as there is no deletion within that specific loop.

---
 include/net/if_inet6.h |  8 ++++++++
 net/ipv6/addrconf.c    | 30 ++++++++++++++++++++++++------
 2 files changed, 32 insertions(+), 6 deletions(-)
include/net/if_inet6.h +8 -0
index f026cf08a8e8..471461023443 100644
@@ -64,6 +64,14 @@ struct inet6_ifaddr {
 
 	struct hlist_node	addr_lst;
 	struct list_head	if_list;
+	/*
+	 * Used to safely traverse idev->addr_list in process context
+	 * if the idev->lock needed to protect idev->addr_list cannot be held.
+	 * In that case, add the items to this list temporarily and iterate
+	 * without holding idev->lock.
+	 * See addrconf_ifdown and dev_forward_change.
+	 */
+	struct list_head	if_list_aux;
 
 	struct list_head	tmp_list;
 	struct inet6_ifaddr	*ifpub;
net/ipv6/addrconf.c +24 -6
index 4df84013c4e6..0a9e03465001 100644
@@ -800,6 +800,7 @@ static void dev_forward_change(struct inet6_dev *idev)
 {
 	struct net_device *dev;
 	struct inet6_ifaddr *ifa;
+	LIST_HEAD(tmp_addr_list);
 
 	if (!idev)
 		return;
@@ -818,14 +819,24 @@ static void dev_forward_change(struct inet6_dev *idev)
 		}
 	}
 
+	read_lock_bh(&idev->lock);
 	list_for_each_entry(ifa, &idev->addr_list, if_list) {
 		if (ifa->flags&IFA_F_TENTATIVE)
 			continue;
+		list_add_tail(&ifa->if_list_aux, &tmp_addr_list);
+	}
+	read_unlock_bh(&idev->lock);
+
+	while (!list_empty(&tmp_addr_list)) {
+		ifa = list_first_entry(&tmp_addr_list,
+				       struct inet6_ifaddr, if_list_aux);
+		list_del(&ifa->if_list_aux);
 		if (idev->cnf.forwarding)
 			addrconf_join_anycast(ifa);
 		else
 			addrconf_leave_anycast(ifa);
 	}
+
 	inet6_netconf_notify_devconf(dev_net(dev), RTM_NEWNETCONF,
 				     NETCONFA_FORWARDING,
 				     dev->ifindex, &idev->cnf);
@@ -3730,7 +3741,8 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)
 	unsigned long event = unregister ? NETDEV_UNREGISTER : NETDEV_DOWN;
 	struct net *net = dev_net(dev);
 	struct inet6_dev *idev;
-	struct inet6_ifaddr *ifa, *tmp;
+	struct inet6_ifaddr *ifa;
+	LIST_HEAD(tmp_addr_list);
 	bool keep_addr = false;
 	bool was_ready;
 	int state, i;
@@ -3822,16 +3834,23 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)
 		write_lock_bh(&idev->lock);
 	}
 
-	list_for_each_entry_safe(ifa, tmp, &idev->addr_list, if_list) {
+	list_for_each_entry(ifa, &idev->addr_list, if_list)
+		list_add_tail(&ifa->if_list_aux, &tmp_addr_list);
+	write_unlock_bh(&idev->lock);
+
+	while (!list_empty(&tmp_addr_list)) {
 		struct fib6_info *rt = NULL;
 		bool keep;
 
+		ifa = list_first_entry(&tmp_addr_list,
+				       struct inet6_ifaddr, if_list_aux);
+		list_del(&ifa->if_list_aux);
+
 		addrconf_del_dad_work(ifa);
 
 		keep = keep_addr && (ifa->flags & IFA_F_PERMANENT) &&
 			!addr_is_local(&ifa->addr);
 
-		write_unlock_bh(&idev->lock);
 		spin_lock_bh(&ifa->lock);
 
 		if (keep) {
@@ -3862,15 +3881,14 @@ static int addrconf_ifdown(struct net_device *dev, bool unregister)
 			addrconf_leave_solict(ifa->idev, &ifa->addr);
 		}
 
-		write_lock_bh(&idev->lock);
 		if (!keep) {
+			write_lock_bh(&idev->lock);
 			list_del_rcu(&ifa->if_list);
+			write_unlock_bh(&idev->lock);
 			in6_ifa_put(ifa);
 		}
 	}
 
-	write_unlock_bh(&idev->lock);
-
 	/* Step 5: Discard anycast and multicast list */
 	if (unregister) {
 		ipv6_ac_destroy_dev(idev);
Signature · 1 line
2.35.1
author maintainer
#12 lore raw

PATCH 13/135 fbcon: Consistently protect deferred_takeover with console_lock()

In reply to Sasha Levin

From: Daniel Vetter <[email protected]>

[ Upstream commit 43553559121ca90965b572cf8a1d6d0fd618b449 ]

This shouldn't be a problem in practice since until we've actually taken over the console there's nothing we've registered with the console/vt subsystem, so the exit/unbind path that check this can't do the wrong thing. But it's confusing, so fix it by moving it a tad later.

---
 drivers/video/fbdev/core/fbcon.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/video/fbdev/core/fbcon.c +3 -2
index 2fc1b80a26ad..9a8ae6fa6ecb 100644
@@ -3265,6 +3265,9 @@ static void fbcon_register_existing_fbs(struct work_struct *work)
 
 	console_lock();
 
+	deferred_takeover = false;
+	logo_shown = FBCON_LOGO_DONTSHOW;
+
 	for_each_registered_fb(i)
 		fbcon_fb_registered(registered_fb[i]);
 
@@ -3282,8 +3285,6 @@ static int fbcon_output_notifier(struct notifier_block *nb,
 	pr_info("fbcon: Taking over console\n");
 
 	dummycon_unregister_output_notifier(&fbcon_output_nb);
-	deferred_takeover = false;
-	logo_shown = FBCON_LOGO_DONTSHOW;
 
 	/* We may get called in atomic context */
 	schedule_work(&fbcon_deferred_takeover_work);
Signature · 1 line
2.35.1
author maintainer
#13 lore raw

PATCH 14/135 x86/platform/uv: Update TSC sync state for UV5

In reply to Sasha Levin

From: Mike Travis <[email protected]>

[ Upstream commit bb3ab81bdbd53f88f26ffabc9fb15bd8466486ec ]

The UV5 platform synchronizes the TSCs among all chassis, and will not proceed to OS boot without achieving synchronization. Previous UV platforms provided a register indicating successful synchronization. This is no longer available on UV5. On this platform TSC_ADJUST should not be reset by the kernel.

---
 arch/x86/kernel/apic/x2apic_uv_x.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
arch/x86/kernel/apic/x2apic_uv_x.c +7 -1
index f5a48e66e4f5..a6e9c2794ef5 100644
@@ -199,7 +199,13 @@ static void __init uv_tsc_check_sync(void)
 	int mmr_shift;
 	char *state;
 
-	/* Different returns from different UV BIOS versions */
+	/* UV5 guarantees synced TSCs; do not zero TSC_ADJUST */
+	if (!is_uv(UV2|UV3|UV4)) {
+		mark_tsc_async_resets("UV5+");
+		return;
+	}
+
+	/* UV2,3,4, UV BIOS TSC sync state available */
 	mmr = uv_early_read_mmr(UVH_TSC_SYNC_MMR);
 	mmr_shift =
 		is_uv2_hub() ? UVH_TSC_SYNC_SHIFT_UV2K : UVH_TSC_SYNC_SHIFT;
Signature · 1 line
2.35.1
author maintainer
#14 lore raw

PATCH 15/135 ACPICA: Avoid cache flush inside virtual machines

In reply to Sasha Levin

From: "Kirill A. Shutemov" <[email protected]>

[ Upstream commit e2efb6359e620521d1e13f69b2257de8ceaa9475 ]

While running inside virtual machine, the kernel can bypass cache flushing. Changing sleep state in a virtual machine doesn't affect the host system sleep state and cannot lead to data loss.

Before entering sleep states, the ACPI code flushes caches to prevent data loss using the WBINVD instruction. This mechanism is required on bare metal.

But, any use WBINVD inside of a guest is worthless. Changing sleep state in a virtual machine doesn't affect the host system sleep state and cannot lead to data loss, so most hypervisors simply ignore it. Despite this, the ACPI code calls WBINVD unconditionally anyway. It's useless, but also normally harmless.

In TDX guests, though, WBINVD stops being harmless; it triggers a virtualization exception (#VE). If the ACPI cache-flushing WBINVD were left in place, TDX guests would need handling to recover from the exception.

Avoid using WBINVD whenever running under a hypervisor. This both removes the useless WBINVDs and saves TDX from implementing WBINVD handling.

---
 arch/x86/include/asm/acenv.h | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
arch/x86/include/asm/acenv.h +13 -1
index 9aff97f0de7f..d937c55e717e 100644
@@ -13,7 +13,19 @@
 
 /* Asm macros */
 
-#define ACPI_FLUSH_CPU_CACHE()	wbinvd()
+/*
+ * ACPI_FLUSH_CPU_CACHE() flushes caches on entering sleep states.
+ * It is required to prevent data loss.
+ *
+ * While running inside virtual machine, the kernel can bypass cache flushing.
+ * Changing sleep state in a virtual machine doesn't affect the host system
+ * sleep state and cannot lead to data loss.
+ */
+#define ACPI_FLUSH_CPU_CACHE()					\
+do {								\
+	if (!cpu_feature_enabled(X86_FEATURE_HYPERVISOR))	\
+		wbinvd();					\
+} while (0)
 
 int __acpi_acquire_global_lock(unsigned int *lock);
 int __acpi_release_global_lock(unsigned int *lock);
Signature · 1 line
2.35.1
author maintainer
#15 lore raw

PATCH 16/135 libbpf: Fix a bug with checking bpf_probe_read_kernel() support in old kernels

In reply to Sasha Levin

From: Runqing Yang <[email protected]>

[ Upstream commit d252a4a499a07bec21c65873f605c3a1ef52ffed ]

Background:
Libbpf automatically replaces calls to BPF bpf_probe_read_{kernel,user} [_str]() helpers with bpf_probe_read[_str](), if libbpf detects that kernel doesn't support new APIs. Specifically, libbpf invokes the probe_kern_probe_read_kernel function to load a small eBPF program into the kernel in which bpf_probe_read_kernel API is invoked and lets the kernel checks whether the new API is valid. If the loading fails, libbpf considers the new API invalid and replaces it with the old API.

static int probe_kern_probe_read_kernel(void)

{
	struct bpf_insn insns[] = {
		BPF_MOV64_REG(BPF_REG_1, BPF_REG_10),	/* r1 = r10 (fp) */
		BPF_ALU64_IMM(BPF_ADD, BPF_REG_1, -8),	/* r1 += -8 */
		BPF_MOV64_IMM(BPF_REG_2, 8),		/* r2 = 8 */
		BPF_MOV64_IMM(BPF_REG_3, 0),		/* r3 = 0 */
		BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0, BPF_FUNC_probe_read_kernel),
		BPF_EXIT_INSN(),
	};
	int fd, insn_cnt = ARRAY_SIZE(insns);

	fd = bpf_prog_load(BPF_PROG_TYPE_KPROBE, NULL,
                           "GPL", insns, insn_cnt, NULL);
	return probe_fd(fd);
}

Bug:
On older kernel versions [0], the kernel checks whether the version number provided in the bpf syscall, matches the LINUX_VERSION_CODE. If not matched, the bpf syscall fails. eBPF However, the probe_kern_probe_read_kernel code does not set the kernel version number provided to the bpf syscall, which causes the loading process alwasys fails for old versions. It means that libbpf will replace the new API with the old one even the kernel supports the new one.

Solution:
After a discussion in [1], the solution is using BPF_PROG_TYPE_TRACEPOINT program type instead of BPF_PROG_TYPE_KPROBE because kernel does not enfoce version check for tracepoint programs. I test the patch in old kernels (4.18 and 4.19) and it works well.

[0] https://elixir.bootlin.com/linux/v4.19/source/kernel/bpf/syscall.c#L1360
[1] Closes: https://github.com/libbpf/libbpf/issues/473

---
 tools/lib/bpf/libbpf.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/lib/bpf/libbpf.c +1 -1
index 94a6a8543cbc..41515a770e3a 100644
@@ -4564,7 +4564,7 @@ static int probe_kern_probe_read_kernel(void)
 	};
 	int fd, insn_cnt = ARRAY_SIZE(insns);
 
-	fd = bpf_prog_load(BPF_PROG_TYPE_KPROBE, NULL, "GPL", insns, insn_cnt, NULL);
+	fd = bpf_prog_load(BPF_PROG_TYPE_TRACEPOINT, NULL, "GPL", insns, insn_cnt, NULL);
 	return probe_fd(fd);
 }
 
Signature · 1 line
2.35.1
author maintainer
#16 lore raw

PATCH 17/135 mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs output)

In reply to Sasha Levin

From: Peter Seiderer <[email protected]>

[ Upstream commit 5c6dd7bd569b54c0d2904125d7366aa93f077f67 ]

Using an ath9k card the debugfs output of minstrel_ht looks like the following (note the zero values for the first four rates sum-of success/attempts):

             best    ____________rate__________    ____statistics___    _____last____    ______sum-of________
mode guard #  rate   [name   idx airtime  max_tp]  [avg(tp) avg(prob)]  [retry|suc|att]  [#success | #attempts]
OFDM       1    DP     6.0M  272    1640     5.2       3.1      53.8       3     0 0             0   0
OFDM       1   C       9.0M  273    1104     7.7       4.6      53.8       4     0 0             0   0
OFDM       1  B       12.0M  274     836    10.0       6.0      53.8       4     0 0             0   0
OFDM       1 A    S   18.0M  275     568    14.3       8.5      53.8       5     0 0             0   0
OFDM       1      S   24.0M  276     436    18.1       0.0       0.0       5     0 1            80   1778
OFDM       1          36.0M  277     300    24.9       0.0       0.0       0     0 1             0   107
OFDM       1      S   48.0M  278     236    30.4       0.0       0.0       0     0 0             0   75
OFDM       1          54.0M  279     212    33.0       0.0       0.0       0     0 0             0   72

Total packet count:: ideal 16582 lookaround 885
Average # of aggregated frames per A-MPDU: 1.0

Debugging showed that the rate statistics for the first four rates where stored in the MINSTREL_CCK_GROUP instead of the MINSTREL_OFDM_GROUP because in minstrel_ht_get_stats() the supported check was not honoured as done in various other places, e.g net/mac80211/rc80211_minstrel_ht_debugfs.c:

74 if (!(mi->supported[i] & BIT(j)))
75 continue;

With the patch applied the output looks good:

              best    ____________rate__________    ____statistics___    _____last____    ______sum-of________
mode guard #  rate   [name   idx airtime  max_tp]  [avg(tp) avg(prob)]  [retry|suc|att]  [#success | #attempts]
OFDM       1    D      6.0M  272    1640     5.2       5.2     100.0       3     0 0             1   1
OFDM       1   C       9.0M  273    1104     7.7       7.7     100.0       4     0 0            38   38
OFDM       1  B       12.0M  274     836    10.0       9.9      89.5       4     2 2           372   395
OFDM       1 A   P    18.0M  275     568    14.3      14.3      97.2       5    52 53         6956   7181
OFDM       1      S   24.0M  276     436    18.1       0.0       0.0       0     0 1             6   163
OFDM       1          36.0M  277     300    24.9       0.0       0.0       0     0 1             0   35
OFDM       1      S   48.0M  278     236    30.4       0.0       0.0       0     0 0             0   38
OFDM       1      S   54.0M  279     212    33.0       0.0       0.0       0     0 0             0   38

Total packet count:: ideal 7097 lookaround 287
Average # of aggregated frames per A-MPDU: 1.0

---
 net/mac80211/rc80211_minstrel_ht.c | 3 +++
 1 file changed, 3 insertions(+)
net/mac80211/rc80211_minstrel_ht.c +3 -0
index 9c3b7fc377c1..50cce990784f 100644
@@ -362,6 +362,9 @@ minstrel_ht_get_stats(struct minstrel_priv *mp, struct minstrel_ht_sta *mi,
 
 	group = MINSTREL_CCK_GROUP;
 	for (idx = 0; idx < ARRAY_SIZE(mp->cck_rates); idx++) {
+		if (!(mi->supported[group] & BIT(idx)))
+			continue;
+
 		if (rate->idx != mp->cck_rates[idx])
 			continue;
 
Signature · 1 line
2.35.1
author maintainer
#17 lore raw

PATCH 18/135 drm/komeda: return early if drm_universal_plane_init() fails.

In reply to Sasha Levin

From: Liviu Dudau <[email protected]>

[ Upstream commit c8f76c37cc3668ee45e081e76a15f24a352ebbdd ]

If drm_universal_plane_init() fails early we jump to the common cleanup code that calls komeda_plane_destroy() which in turn could access the uninitalised drm_plane and crash. Return early if an error is detected without going through the common code.

---
 drivers/gpu/drm/arm/display/komeda/komeda_plane.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/gpu/drm/arm/display/komeda/komeda_plane.c +4 -2
index d63d83800a8a..d646e3ae1a23 100644
@@ -275,8 +275,10 @@ static int komeda_plane_add(struct komeda_kms_dev *kms,
 
 	komeda_put_fourcc_list(formats);
 
-	if (err)
-		goto cleanup;
+	if (err) {
+		kfree(kplane);
+		return err;
+	}
 
 	drm_plane_helper_add(plane, &komeda_plane_helper_funcs);
 
Signature · 1 line
2.35.1
author maintainer
#18 lore raw

PATCH 19/135 drm/amd/display: Disabling Z10 on DCN31

In reply to Sasha Levin

From: Saaem Rizvi <[email protected]>

[ Upstream commit 5d5af34072c8b11f60960c3bea57ff9de5877791 ]

[WHY]
Z10 is should not be enabled by default on DCN31.

[HOW]
Using DC debug flags to disable Z10 by default on DCN31.

---
 drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c | 1 +
 1 file changed, 1 insertion(+)
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c +1 -0
index f3933c9f5746..6966b72eefc6 100644
@@ -1030,6 +1030,7 @@ static const struct dc_debug_options debug_defaults_drv = {
 			.afmt = true,
 		}
 	},
+	.disable_z10 = true,
 	.optimize_edp_link_rate = true,
 	.enable_sw_cntl_psr = true,
 	.apply_vendor_specific_lttpr_wa = true,
Signature · 1 line
2.35.1
author maintainer
#19 lore raw

PATCH 20/135 rcu-tasks: Fix race in schedule and flush work

In reply to Sasha Levin

From: Padmanabha Srinivasaiah <[email protected]>

[ Upstream commit f75fd4b9221d93177c50dcfde671b2e907f53e86 ]

While booting secondary CPUs, cpus_read_[lock/unlock] is not keeping online cpumask stable. The transient online mask results in below calltrace.

[    0.324121] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[    0.346652] Detected PIPT I-cache on CPU2
[    0.347212] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[    0.377255] Detected PIPT I-cache on CPU3
[    0.377823] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[    0.379040] ------------[ cut here ]------------
[    0.383662] WARNING: CPU: 0 PID: 10 at kernel/workqueue.c:3084 __flush_work+0x12c/0x138
[    0.384850] Modules linked in:
[    0.385403] CPU: 0 PID: 10 Comm: rcu_tasks_rude_ Not tainted 5.17.0-rc3-v8+ #13
[    0.386473] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[    0.387289] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    0.388308] pc : __flush_work+0x12c/0x138
[    0.388970] lr : __flush_work+0x80/0x138
[    0.389620] sp : ffffffc00aaf3c60
[    0.390139] x29: ffffffc00aaf3d20 x28: ffffffc009c16af0 x27: ffffff80f761df48
[    0.391316] x26: 0000000000000004 x25: 0000000000000003 x24: 0000000000000100
[    0.392493] x23: ffffffffffffffff x22: ffffffc009c16b10 x21: ffffffc009c16b28
[    0.393668] x20: ffffffc009e53861 x19: ffffff80f77fbf40 x18: 00000000d744fcc9
[    0.394842] x17: 000000000000000b x16: 00000000000001c2 x15: ffffffc009e57550
[    0.396016] x14: 0000000000000000 x13: ffffffffffffffff x12: 0000000100000000
[    0.397190] x11: 0000000000000462 x10: ffffff8040258008 x9 : 0000000100000000
[    0.398364] x8 : 0000000000000000 x7 : ffffffc0093c8bf4 x6 : 0000000000000000
[    0.399538] x5 : 0000000000000000 x4 : ffffffc00a976e40 x3 : ffffffc00810444c
[    0.400711] x2 : 0000000000000004 x1 : 0000000000000000 x0 : 0000000000000000
[    0.401886] Call trace:
[    0.402309]  __flush_work+0x12c/0x138
[    0.402941]  schedule_on_each_cpu+0x228/0x278
[    0.403693]  rcu_tasks_rude_wait_gp+0x130/0x144
[    0.404502]  rcu_tasks_kthread+0x220/0x254
[    0.405264]  kthread+0x174/0x1ac
[    0.405837]  ret_from_fork+0x10/0x20
[    0.406456] irq event stamp: 102
[    0.406966] hardirqs last  enabled at (101): [<ffffffc0093c8468>] _raw_spin_unlock_irq+0x78/0xb4
[    0.408304] hardirqs last disabled at (102): [<ffffffc0093b8270>] el1_dbg+0x24/0x5c
[    0.409410] softirqs last  enabled at (54): [<ffffffc0081b80c8>] local_bh_enable+0xc/0x2c
[    0.410645] softirqs last disabled at (50): [<ffffffc0081b809c>] local_bh_disable+0xc/0x2c
[    0.411890] ---[ end trace 0000000000000000 ]---
[    0.413000] smp: Brought up 1 node, 4 CPUs
[    0.413762] SMP: Total of 4 processors activated.
[    0.414566] CPU features: detected: 32-bit EL0 Support
[    0.415414] CPU features: detected: 32-bit EL1 Support
[    0.416278] CPU features: detected: CRC32 instructions
[    0.447021] Callback from call_rcu_tasks_rude() invoked.
[    0.506693] Callback from call_rcu_tasks() invoked.

This commit therefore fixes this issue by applying a single-CPU optimization to the RCU Tasks Rude grace-period process. The key point here is that the purpose of this RCU flavor is to force a schedule on each online CPU since some past event. But the rcu_tasks_rude_wait_gp() function runs in the context of the RCU Tasks Rude's grace-period kthread, so there must already have been a context switch on the current CPU since the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude(). So if there is only a single CPU online, RCU Tasks Rude's grace-period kthread does not need to anything at all.

It turns out that the rcu_tasks_rude_wait_gp() function's call to schedule_on_each_cpu() causes problems during early boot. During that time, there is only one online CPU, namely the boot CPU. Therefore, applying this single-CPU optimization fixes early-boot instances of this problem.

---
 kernel/rcu/tasks.h | 3 +++
 1 file changed, 3 insertions(+)
kernel/rcu/tasks.h +3 -0
index d64f0b1d8cd3..30c42797f53b 100644
@@ -950,6 +950,9 @@ static void rcu_tasks_be_rude(struct work_struct *work)
 // Wait for one rude RCU-tasks grace period.
 static void rcu_tasks_rude_wait_gp(struct rcu_tasks *rtp)
 {
+	if (num_online_cpus() <= 1)
+		return;	// Fastpath for only one CPU.
+
 	rtp->n_ipis += cpumask_weight(cpu_online_mask);
 	schedule_on_each_cpu(rcu_tasks_be_rude);
 }
Signature · 1 line
2.35.1
author maintainer
#20 lore raw

PATCH 21/135 rcu-tasks: Handle sparse cpu_possible_mask in rcu_tasks_invoke_cbs()

In reply to Sasha Levin

From: "Paul E. McKenney" <[email protected]>

[ Upstream commit ab2756ea6b74987849b44ad0e33c3cfec159033b ]

If the cpu_possible_mask is sparse (for example, if bits are set only for CPUs 0, 4, 8, ...), then rcu_tasks_invoke_cbs() will access per-CPU data for a CPU not in cpu_possible_mask. It makes these accesses while doing a workqueue-based binary search for non-empty callback lists. Although this search must pass through CPUs not represented in cpu_possible_mask, it has no need to check the callback list for such CPUs.

This commit therefore changes the rcu_tasks_invoke_cbs() function's binary search so as to only check callback lists for CPUs present in cpu_possible_mask.

---
 kernel/rcu/tasks.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/rcu/tasks.h +1 -1
index 30c42797f53b..1664e472524b 100644
@@ -460,7 +460,7 @@ static void rcu_tasks_invoke_cbs(struct rcu_tasks *rtp, struct rcu_tasks_percpu
 		}
 	}
 
-	if (rcu_segcblist_empty(&rtpcp->cblist))
+	if (rcu_segcblist_empty(&rtpcp->cblist) || !cpu_possible(cpu))
 		return;
 	raw_spin_lock_irqsave_rcu_node(rtpcp, flags);
 	rcu_segcblist_advance(&rtpcp->cblist, rcu_seq_current(&rtp->tasks_gp_seq));
Signature · 1 line
2.35.1
author maintainer
#21 lore raw

PATCH 22/135 rcu: Make TASKS_RUDE_RCU select IRQ_WORK

In reply to Sasha Levin

From: "Paul E. McKenney" <[email protected]>

[ Upstream commit 46e861be589881e0905b9ade3d8439883858721c ]

The TASKS_RUDE_RCU does not select IRQ_WORK, which can result in build failures for kernels that do not otherwise select IRQ_WORK. This commit therefore causes the TASKS_RUDE_RCU Kconfig option to select IRQ_WORK.

---
 kernel/rcu/Kconfig | 1 +
 1 file changed, 1 insertion(+)
kernel/rcu/Kconfig +1 -0
index bf8e341e75b4..f559870fbf8b 100644
@@ -86,6 +86,7 @@ config TASKS_RCU
 
 config TASKS_RUDE_RCU
 	def_bool 0
+	select IRQ_WORK
 	help
 	  This option enables a task-based RCU implementation that uses
 	  only context switch (including preemption) and user-mode
Signature · 1 line
2.35.1
author maintainer
#22 lore raw

PATCH 23/135 sfc: ef10: Fix assigning negative value to unsigned variable

In reply to Sasha Levin

From: Haowen Bai <[email protected]>

[ Upstream commit b8ff3395fbdf3b79a99d0ef410fc34c51044121e ]

fix warning reported by smatch:
251 drivers/net/ethernet/sfc/ef10.c:2259 efx_ef10_tx_tso_desc()
warn: assigning (-208) to unsigned variable 'ip_tot_len'

---
 drivers/net/ethernet/sfc/ef10.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/sfc/ef10.c +1 -1
index 1ab725d554a5..e50dea0e3859 100644
@@ -2256,7 +2256,7 @@ int efx_ef10_tx_tso_desc(struct efx_tx_queue *tx_queue, struct sk_buff *skb,
 	 * guaranteed to satisfy the second as we only attempt TSO if
 	 * inner_network_header <= 208.
 	 */
-	ip_tot_len = -EFX_TSO2_MAX_HDRLEN;
+	ip_tot_len = 0x10000 - EFX_TSO2_MAX_HDRLEN;
 	EFX_WARN_ON_ONCE_PARANOID(mss + EFX_TSO2_MAX_HDRLEN +
 				  (tcp->doff << 2u) > ip_tot_len);
 
Signature · 1 line
2.35.1
author maintainer
#23 lore raw

PATCH 24/135 ALSA: jack: Access input_dev under mutex

In reply to Sasha Levin

From: Amadeusz Sławiński <[email protected]>

[ Upstream commit 1b6a6fc5280e97559287b61eade2d4b363e836f2 ]

It is possible when using ASoC that input_dev is unregistered while calling snd_jack_report, which causes NULL pointer dereference. In order to prevent this serialize access to input_dev using mutex lock.

---
 include/sound/jack.h |  1 +
 sound/core/jack.c    | 34 +++++++++++++++++++++++++++-------
 2 files changed, 28 insertions(+), 7 deletions(-)
include/sound/jack.h +1 -0
index 1181f536557e..1ed90e2109e9 100644
@@ -62,6 +62,7 @@ struct snd_jack {
 	const char *id;
 #ifdef CONFIG_SND_JACK_INPUT_DEV
 	struct input_dev *input_dev;
+	struct mutex input_dev_lock;
 	int registered;
 	int type;
 	char name[100];
sound/core/jack.c +27 -7
index d1e3055f2b6a..88493cc31914 100644
@@ -42,8 +42,11 @@ static int snd_jack_dev_disconnect(struct snd_device *device)
 #ifdef CONFIG_SND_JACK_INPUT_DEV
 	struct snd_jack *jack = device->device_data;
 
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return 0;
+	}
 
 	/* If the input device is registered with the input subsystem
 	 * then we need to use a different deallocator. */
@@ -52,6 +55,7 @@ static int snd_jack_dev_disconnect(struct snd_device *device)
 	else
 		input_free_device(jack->input_dev);
 	jack->input_dev = NULL;
+	mutex_unlock(&jack->input_dev_lock);
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
 	return 0;
 }
@@ -90,8 +94,11 @@ static int snd_jack_dev_register(struct snd_device *device)
 	snprintf(jack->name, sizeof(jack->name), "%s %s",
 		 card->shortname, jack->id);
 
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return 0;
+	}
 
 	jack->input_dev->name = jack->name;
 
@@ -116,6 +123,7 @@ static int snd_jack_dev_register(struct snd_device *device)
 	if (err == 0)
 		jack->registered = 1;
 
+	mutex_unlock(&jack->input_dev_lock);
 	return err;
 }
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
@@ -517,9 +525,11 @@ int snd_jack_new(struct snd_card *card, const char *id, int type,
 		return -ENOMEM;
 	}
 
-	/* don't creat input device for phantom jack */
-	if (!phantom_jack) {
 #ifdef CONFIG_SND_JACK_INPUT_DEV
+	mutex_init(&jack->input_dev_lock);
+
+	/* don't create input device for phantom jack */
+	if (!phantom_jack) {
 		int i;
 
 		jack->input_dev = input_allocate_device();
@@ -537,8 +547,8 @@ int snd_jack_new(struct snd_card *card, const char *id, int type,
 				input_set_capability(jack->input_dev, EV_SW,
 						     jack_switch_types[i]);
 
-#endif /* CONFIG_SND_JACK_INPUT_DEV */
 	}
+#endif /* CONFIG_SND_JACK_INPUT_DEV */
 
 	err = snd_device_new(card, SNDRV_DEV_JACK, jack, &ops);
 	if (err < 0)
@@ -578,10 +588,14 @@ EXPORT_SYMBOL(snd_jack_new);
 void snd_jack_set_parent(struct snd_jack *jack, struct device *parent)
 {
 	WARN_ON(jack->registered);
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return;
+	}
 
 	jack->input_dev->dev.parent = parent;
+	mutex_unlock(&jack->input_dev_lock);
 }
 EXPORT_SYMBOL(snd_jack_set_parent);
 
@@ -629,6 +643,8 @@ EXPORT_SYMBOL(snd_jack_set_key);
 
 /**
  * snd_jack_report - Report the current status of a jack
+ * Note: This function uses mutexes and should be called from a
+ * context which can sleep (such as a workqueue).
  *
  * @jack:   The jack to report status for
  * @status: The current status of the jack
@@ -654,8 +670,11 @@ void snd_jack_report(struct snd_jack *jack, int status)
 					     status & jack_kctl->mask_bits);
 
 #ifdef CONFIG_SND_JACK_INPUT_DEV
-	if (!jack->input_dev)
+	mutex_lock(&jack->input_dev_lock);
+	if (!jack->input_dev) {
+		mutex_unlock(&jack->input_dev_lock);
 		return;
+	}
 
 	for (i = 0; i < ARRAY_SIZE(jack->key); i++) {
 		int testbit = ((SND_JACK_BTN_0 >> i) & ~mask_bits);
@@ -675,6 +694,7 @@ void snd_jack_report(struct snd_jack *jack, int status)
 	}
 
 	input_sync(jack->input_dev);
+	mutex_unlock(&jack->input_dev_lock);
 #endif /* CONFIG_SND_JACK_INPUT_DEV */
 }
 EXPORT_SYMBOL(snd_jack_report);
Signature · 1 line
2.35.1
author maintainer
#24 lore raw

PATCH 25/135 rtw88: fix incorrect frequency reported

In reply to Sasha Levin

From: Po-Hao Huang <[email protected]>

[ Upstream commit 6723c0cde84fde582a261c186ce84100dcfa0019 ]

We should only fill in frequency reported by firmware during scan. Add this so frames won't be dropped by mac80211 due to frequency mismatch.

---
 drivers/net/wireless/realtek/rtw88/rx.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/wireless/realtek/rtw88/rx.c +2 -1
index d2d607e22198..84aedabdf285 100644
@@ -158,7 +158,8 @@ void rtw_rx_fill_rx_status(struct rtw_dev *rtwdev,
 	memset(rx_status, 0, sizeof(*rx_status));
 	rx_status->freq = hw->conf.chandef.chan->center_freq;
 	rx_status->band = hw->conf.chandef.chan->band;
-	if (rtw_fw_feature_check(&rtwdev->fw, FW_FEATURE_SCAN_OFFLOAD))
+	if (rtw_fw_feature_check(&rtwdev->fw, FW_FEATURE_SCAN_OFFLOAD) &&
+	    test_bit(RTW_FLAG_SCANNING, rtwdev->flags))
 		rtw_set_rx_freq_by_pktstat(pkt_stat, rx_status);
 	if (pkt_stat->crc_err)
 		rx_status->flag |= RX_FLAG_FAILED_FCS_CRC;
Signature · 1 line
2.35.1
author maintainer
#25 lore raw

PATCH 26/135 rtw88: 8821c: fix debugfs rssi value

In reply to Sasha Levin

From: Po-Hao Huang <[email protected]>

[ Upstream commit ece31c93d4d68f7eb8eea4431b052aacdb678de2 ]

RSSI value per frame is reported to mac80211 but not maintained in our own statistics, add it back to help us debug.

---
 drivers/net/wireless/realtek/rtw88/rtw8821c.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/net/wireless/realtek/rtw88/rtw8821c.c +4 -0
index 80d4761796b1..0f16f649e03f 100644
@@ -512,6 +512,7 @@ static s8 get_cck_rx_pwr(struct rtw_dev *rtwdev, u8 lna_idx, u8 vga_idx)
 static void query_phy_status_page0(struct rtw_dev *rtwdev, u8 *phy_status,
 				   struct rtw_rx_pkt_stat *pkt_stat)
 {
+	struct rtw_dm_info *dm_info = &rtwdev->dm_info;
 	s8 rx_power;
 	u8 lna_idx = 0;
 	u8 vga_idx = 0;
@@ -523,6 +524,7 @@ static void query_phy_status_page0(struct rtw_dev *rtwdev, u8 *phy_status,
 
 	pkt_stat->rx_power[RF_PATH_A] = rx_power;
 	pkt_stat->rssi = rtw_phy_rf_power_2_rssi(pkt_stat->rx_power, 1);
+	dm_info->rssi[RF_PATH_A] = pkt_stat->rssi;
 	pkt_stat->bw = RTW_CHANNEL_WIDTH_20;
 	pkt_stat->signal_power = rx_power;
 }
@@ -530,6 +532,7 @@ static void query_phy_status_page0(struct rtw_dev *rtwdev, u8 *phy_status,
 static void query_phy_status_page1(struct rtw_dev *rtwdev, u8 *phy_status,
 				   struct rtw_rx_pkt_stat *pkt_stat)
 {
+	struct rtw_dm_info *dm_info = &rtwdev->dm_info;
 	u8 rxsc, bw;
 	s8 min_rx_power = -120;
 
@@ -549,6 +552,7 @@ static void query_phy_status_page1(struct rtw_dev *rtwdev, u8 *phy_status,
 
 	pkt_stat->rx_power[RF_PATH_A] = GET_PHY_STAT_P1_PWDB_A(phy_status) - 110;
 	pkt_stat->rssi = rtw_phy_rf_power_2_rssi(pkt_stat->rx_power, 1);
+	dm_info->rssi[RF_PATH_A] = pkt_stat->rssi;
 	pkt_stat->bw = bw;
 	pkt_stat->signal_power = max(pkt_stat->rx_power[RF_PATH_A],
 				     min_rx_power);
Signature · 1 line
2.35.1
author maintainer
#26 lore raw

PATCH 27/135 spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA direction

In reply to Sasha Levin

From: Biju Das <[email protected]>

[ Upstream commit 6f381481a5b236cb53d6de2c49c6ef83a4d0f432 ]

The direction field in the DMA config is deprecated. The rspi driver sets {src,dst}_{addr,addr_width} based on the DMA direction and it results in dmaengine_slave_config() failure as RZ DMAC driver validates {src,dst}_addr_width values independent of DMA direction.

This patch fixes the issue by passing both {src,dst}_{addr,addr_width} values independent of DMA direction.

---
 drivers/spi/spi-rspi.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/spi/spi-rspi.c +6 -9
index bd5708d7e5a1..7a014eeec2d0 100644
@@ -1108,14 +1108,11 @@ static struct dma_chan *rspi_request_dma_chan(struct device *dev,
 	}
 
 	memset(&cfg, 0, sizeof(cfg));
+	cfg.dst_addr = port_addr + RSPI_SPDR;
+	cfg.src_addr = port_addr + RSPI_SPDR;
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 	cfg.direction = dir;
-	if (dir == DMA_MEM_TO_DEV) {
-		cfg.dst_addr = port_addr;
-		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	} else {
-		cfg.src_addr = port_addr;
-		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	}
 
 	ret = dmaengine_slave_config(chan, &cfg);
 	if (ret) {
@@ -1146,12 +1143,12 @@ static int rspi_request_dma(struct device *dev, struct spi_controller *ctlr,
 	}
 
 	ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_tx)
 		return -ENODEV;
 
 	ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_rx) {
 		dma_release_channel(ctlr->dma_tx);
 		ctlr->dma_tx = NULL;
Signature · 1 line
2.35.1
author maintainer
#27 lore raw

PATCH 28/135 tools/power turbostat: fix ICX DRAM power numbers

In reply to Sasha Levin

From: Len Brown <[email protected]>

[ Upstream commit 6397b6418935773a34b533b3348b03f4ce3d7050 ]

ICX (and its duplicates) require special hard-coded DRAM RAPL units, rather than using the generic RAPL energy units.

---
 tools/power/x86/turbostat/turbostat.c | 1 +
 1 file changed, 1 insertion(+)
tools/power/x86/turbostat/turbostat.c +1 -0
index 47d3ba895d6d..4f176bbf29f4 100644
@@ -4376,6 +4376,7 @@ static double rapl_dram_energy_units_probe(int model, double rapl_energy_units)
 	case INTEL_FAM6_BROADWELL_X:	/* BDX */
 	case INTEL_FAM6_SKYLAKE_X:	/* SKX */
 	case INTEL_FAM6_XEON_PHI_KNL:	/* KNL */
+	case INTEL_FAM6_ICELAKE_X:	/* ICX */
 		return (rapl_dram_energy_units = 15.3 / 1000000);
 	default:
 		return (rapl_energy_units);
Signature · 1 line
2.35.1
author maintainer
#28 lore raw

PATCH 29/135 tcp: consume incoming skb leading to a reset

In reply to Sasha Levin

From: Eric Dumazet <[email protected]>

[ Upstream commit d9d024f96609016628d750ebc8ee4a6f0d80e6e1 ]

Whenever tcp_validate_incoming() handles a valid RST packet, we should not pretend the packet was dropped.

Create a special section at the end of tcp_validate_incoming() to handle this case.

---
 net/ipv4/tcp_input.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)
net/ipv4/tcp_input.c +16 -12
index 7bf84ce34d9e..96c25c97ee56 100644
@@ -5694,7 +5694,7 @@ static bool tcp_validate_incoming(struct sock *sk, struct sk_buff *skb,
 						  &tp->last_oow_ack_time))
 				tcp_send_dupack(sk, skb);
 		} else if (tcp_reset_check(sk, skb)) {
-			tcp_reset(sk, skb);
+			goto reset;
 		}
 		goto discard;
 	}
@@ -5730,17 +5730,16 @@ static bool tcp_validate_incoming(struct sock *sk, struct sk_buff *skb,
 		}
 
 		if (rst_seq_match)
-			tcp_reset(sk, skb);
-		else {
-			/* Disable TFO if RST is out-of-order
-			 * and no data has been received
-			 * for current active TFO socket
-			 */
-			if (tp->syn_fastopen && !tp->data_segs_in &&
-			    sk->sk_state == TCP_ESTABLISHED)
-				tcp_fastopen_active_disable(sk);
-			tcp_send_challenge_ack(sk);
-		}
+			goto reset;
+
+		/* Disable TFO if RST is out-of-order
+		 * and no data has been received
+		 * for current active TFO socket
+		 */
+		if (tp->syn_fastopen && !tp->data_segs_in &&
+		    sk->sk_state == TCP_ESTABLISHED)
+			tcp_fastopen_active_disable(sk);
+		tcp_send_challenge_ack(sk);
 		goto discard;
 	}
 
@@ -5765,6 +5764,11 @@ static bool tcp_validate_incoming(struct sock *sk, struct sk_buff *skb,
 discard:
 	tcp_drop(sk, skb);
 	return false;
+
+reset:
+	tcp_reset(sk, skb);
+	__kfree_skb(skb);
+	return false;
 }
 
 /*
Signature · 1 line
2.35.1
author maintainer
#29 lore raw

PATCH 30/135 scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg()

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit e294647b1aed4247fe52851f3a3b2b19ae906228 ]

In an attempt to log message 0126 with LOG_TRACE_EVENT, the following hard lockup call trace hangs the system.

Call Trace:
 _raw_spin_lock_irqsave+0x32/0x40
 lpfc_dmp_dbg.part.32+0x28/0x220 [lpfc]
 lpfc_cmpl_els_fdisc+0x145/0x460 [lpfc]
 lpfc_sli_cancel_jobs+0x92/0xd0 [lpfc]
 lpfc_els_flush_cmd+0x43c/0x670 [lpfc]
 lpfc_els_flush_all_cmd+0x37/0x60 [lpfc]
 lpfc_sli4_async_event_proc+0x956/0x1720 [lpfc]
 lpfc_do_work+0x1485/0x1d70 [lpfc]
 kthread+0x112/0x130
 ret_from_fork+0x1f/0x40
Kernel panic - not syncing: Hard LOCKUP

The same CPU tries to claim the phba->port_list_lock twice.

Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need to take the phba->port_list_lock within lpfc_dmp_dbg().

---
 drivers/scsi/lpfc/lpfc_init.c   | 29 +----------------------------
 drivers/scsi/lpfc/lpfc_logmsg.h |  6 +++---
 2 files changed, 4 insertions(+), 31 deletions(-)
drivers/scsi/lpfc/lpfc_init.c +1 -28
index 9569a7390f9d..6739bdd8195d 100644
@@ -15712,34 +15712,7 @@ void lpfc_dmp_dbg(struct lpfc_hba *phba)
 	unsigned int temp_idx;
 	int i;
 	int j = 0;
-	unsigned long rem_nsec, iflags;
-	bool log_verbose = false;
-	struct lpfc_vport *port_iterator;
-
-	/* Don't dump messages if we explicitly set log_verbose for the
-	 * physical port or any vport.
-	 */
-	if (phba->cfg_log_verbose)
-		return;
-
-	spin_lock_irqsave(&phba->port_list_lock, iflags);
-	list_for_each_entry(port_iterator, &phba->port_list, listentry) {
-		if (port_iterator->load_flag & FC_UNLOADING)
-			continue;
-		if (scsi_host_get(lpfc_shost_from_vport(port_iterator))) {
-			if (port_iterator->cfg_log_verbose)
-				log_verbose = true;
-
-			scsi_host_put(lpfc_shost_from_vport(port_iterator));
-
-			if (log_verbose) {
-				spin_unlock_irqrestore(&phba->port_list_lock,
-						       iflags);
-				return;
-			}
-		}
-	}
-	spin_unlock_irqrestore(&phba->port_list_lock, iflags);
+	unsigned long rem_nsec;
 
 	if (atomic_cmpxchg(&phba->dbg_log_dmping, 0, 1) != 0)
 		return;
drivers/scsi/lpfc/lpfc_logmsg.h +3 -3
index 7d480c798794..a5aafe230c74 100644
@@ -73,7 +73,7 @@ do { \
 #define lpfc_printf_vlog(vport, level, mask, fmt, arg...) \
 do { \
 	{ if (((mask) & (vport)->cfg_log_verbose) || (level[1] <= '3')) { \
-		if ((mask) & LOG_TRACE_EVENT) \
+		if ((mask) & LOG_TRACE_EVENT && !(vport)->cfg_log_verbose) \
 			lpfc_dmp_dbg((vport)->phba); \
 		dev_printk(level, &((vport)->phba->pcidev)->dev, "%d:(%d):" \
 			   fmt, (vport)->phba->brd_no, vport->vpi, ##arg);  \
@@ -89,11 +89,11 @@ do { \
 				 (phba)->pport->cfg_log_verbose : \
 				 (phba)->cfg_log_verbose; \
 	if (((mask) & log_verbose) || (level[1] <= '3')) { \
-		if ((mask) & LOG_TRACE_EVENT) \
+		if ((mask) & LOG_TRACE_EVENT && !log_verbose) \
 			lpfc_dmp_dbg(phba); \
 		dev_printk(level, &((phba)->pcidev)->dev, "%d:" \
 			fmt, phba->brd_no, ##arg); \
-	} else  if (!(phba)->cfg_log_verbose)\
+	} else if (!log_verbose)\
 		lpfc_dbg_print(phba, "%d:" fmt, phba->brd_no, ##arg); \
 	} \
 } while (0)
Signature · 1 line
2.35.1
author maintainer
#30 lore raw

PATCH 31/135 scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit 03cbbd7c2f5ee288f648f4aeedc765a181188553 ]

During stress I/O tests with 500+ vports, hard LOCKUP call traces are observed.

CPU A:
native_queued_spin_lock_slowpath+0x192
_raw_spin_lock_irqsave+0x32
lpfc_handle_fcp_err+0x4c6
lpfc_fcp_io_cmd_wqe_cmpl+0x964
lpfc_sli4_fp_handle_cqe+0x266
__lpfc_sli4_process_cq+0x105
__lpfc_sli4_hba_process_cq+0x3c
lpfc_cq_poll_hdler+0x16
irq_poll_softirq+0x76
__softirqentry_text_start+0xe4
irq_exit+0xf7
do_IRQ+0x7f

CPU B:
native_queued_spin_lock_slowpath+0x5b
_raw_spin_lock+0x1c
lpfc_abort_handler+0x13e
scmd_eh_abort_handler+0x85
process_one_work+0x1a7
worker_thread+0x30
kthread+0x112
ret_from_fork+0x1f

Diagram of lockup:

CPUA CPUB
---- ----
lpfc_cmd->buf_lock

                            phba->hbalock
                            lpfc_cmd->buf_lock

phba->hbalock

Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock first before phba->hbalock.

---
 drivers/scsi/lpfc/lpfc_scsi.c | 33 +++++++++++++++------------------
 1 file changed, 15 insertions(+), 18 deletions(-)
drivers/scsi/lpfc/lpfc_scsi.c +15 -18
index 5a3da38a9067..6cc94fae01b8 100644
@@ -5907,25 +5907,25 @@ lpfc_abort_handler(struct scsi_cmnd *cmnd)
 	if (!lpfc_cmd)
 		return ret;
 
-	spin_lock_irqsave(&phba->hbalock, flags);
+	/* Guard against IO completion being called at same time */
+	spin_lock_irqsave(&lpfc_cmd->buf_lock, flags);
+
+	spin_lock(&phba->hbalock);
 	/* driver queued commands are in process of being flushed */
 	if (phba->hba_flag & HBA_IOQ_FLUSH) {
 		lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			"3168 SCSI Layer abort requested I/O has been "
 			"flushed by LLD.\n");
 		ret = FAILED;
-		goto out_unlock;
+		goto out_unlock_hba;
 	}
 
-	/* Guard against IO completion being called at same time */
-	spin_lock(&lpfc_cmd->buf_lock);
-
 	if (!lpfc_cmd->pCmd) {
 		lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			 "2873 SCSI Layer I/O Abort Request IO CMPL Status "
 			 "x%x ID %d LUN %llu\n",
 			 SUCCESS, cmnd->device->id, cmnd->device->lun);
-		goto out_unlock_buf;
+		goto out_unlock_hba;
 	}
 
 	iocb = &lpfc_cmd->cur_iocbq;
@@ -5933,7 +5933,7 @@ lpfc_abort_handler(struct scsi_cmnd *cmnd)
 		pring_s4 = phba->sli4_hba.hdwq[iocb->hba_wqidx].io_wq->pring;
 		if (!pring_s4) {
 			ret = FAILED;
-			goto out_unlock_buf;
+			goto out_unlock_hba;
 		}
 		spin_lock(&pring_s4->ring_lock);
 	}
@@ -5966,8 +5966,8 @@ lpfc_abort_handler(struct scsi_cmnd *cmnd)
 			 "3389 SCSI Layer I/O Abort Request is pending\n");
 		if (phba->sli_rev == LPFC_SLI_REV4)
 			spin_unlock(&pring_s4->ring_lock);
-		spin_unlock(&lpfc_cmd->buf_lock);
-		spin_unlock_irqrestore(&phba->hbalock, flags);
+		spin_unlock(&phba->hbalock);
+		spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 		goto wait_for_cmpl;
 	}
 
@@ -5988,15 +5988,13 @@ lpfc_abort_handler(struct scsi_cmnd *cmnd)
 	if (ret_val != IOCB_SUCCESS) {
 		/* Indicate the IO is not being aborted by the driver. */
 		lpfc_cmd->waitq = NULL;
-		spin_unlock(&lpfc_cmd->buf_lock);
-		spin_unlock_irqrestore(&phba->hbalock, flags);
 		ret = FAILED;
-		goto out;
+		goto out_unlock_hba;
 	}
 
 	/* no longer need the lock after this point */
-	spin_unlock(&lpfc_cmd->buf_lock);
-	spin_unlock_irqrestore(&phba->hbalock, flags);
+	spin_unlock(&phba->hbalock);
+	spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 
 	if (phba->cfg_poll & DISABLE_FCP_RING_INT)
 		lpfc_sli_handle_fast_ring_event(phba,
@@ -6031,10 +6029,9 @@ lpfc_abort_handler(struct scsi_cmnd *cmnd)
 out_unlock_ring:
 	if (phba->sli_rev == LPFC_SLI_REV4)
 		spin_unlock(&pring_s4->ring_lock);
-out_unlock_buf:
-	spin_unlock(&lpfc_cmd->buf_lock);
-out_unlock:
-	spin_unlock_irqrestore(&phba->hbalock, flags);
+out_unlock_hba:
+	spin_unlock(&phba->hbalock);
+	spin_unlock_irqrestore(&lpfc_cmd->buf_lock, flags);
 out:
 	lpfc_printf_vlog(vport, KERN_WARNING, LOG_FCP,
 			 "0749 SCSI Layer I/O Abort Request Status x%x ID %d "
Signature · 1 line
2.35.1
author maintainer
#31 lore raw

PATCH 32/135 scsi: lpfc: Fix call trace observed during I/O with CMF enabled

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit d6d45f67a11136cb88a70a29ab22ea6db8ae6bd5 ]

The following was seen with CMF enabled:

BUG: using smp_processor_id() in preemptible

code: systemd-udevd/31711
kernel: caller is lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: CPU: 12 PID: 31711 Comm: systemd-udevd
kernel: Call Trace:
kernel: <TASK>
kernel: dump_stack_lvl+0x44/0x57
kernel: check_preemption_disabled+0xbf/0xe0
kernel: lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: lpfc_nvme_fcp_io_submit+0x23b4/0x4df0 [lpfc]

this_cpu_ptr() calls smp_processor_id() in a preemptible context.

Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.

---
 drivers/scsi/lpfc/lpfc_scsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/scsi/lpfc/lpfc_scsi.c +2 -2
index 6cc94fae01b8..d9a8e3a59d94 100644
@@ -3936,7 +3936,7 @@ lpfc_update_cmf_cmpl(struct lpfc_hba *phba,
 		else
 			time = div_u64(time + 500, 1000); /* round it */
 
-		cgs = this_cpu_ptr(phba->cmf_stat);
+		cgs = per_cpu_ptr(phba->cmf_stat, raw_smp_processor_id());
 		atomic64_add(size, &cgs->rcv_bytes);
 		atomic64_add(time, &cgs->rx_latency);
 		atomic_inc(&cgs->rx_io_cnt);
@@ -3980,7 +3980,7 @@ lpfc_update_cmf_cmd(struct lpfc_hba *phba, uint32_t size)
 			atomic_set(&phba->rx_max_read_cnt, size);
 	}
 
-	cgs = this_cpu_ptr(phba->cmf_stat);
+	cgs = per_cpu_ptr(phba->cmf_stat, raw_smp_processor_id());
 	atomic64_add(size, &cgs->total_bytes);
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#32 lore raw

PATCH 33/135 net: sched: use queue_mapping to pick tx queue

In reply to Sasha Levin

From: Tonghao Zhang <[email protected]>

[ Upstream commit 2f1e85b1aee459b7d0fd981839042c6a38ffaf0c ]

This patch fixes issue:
* If we install tc filters with act_skbedit in clsact hook. It doesn't work, because netdev_core_pick_tx() overwrites queue_mapping.

  $ tc filter ... action skbedit queue_mapping 1

And this patch is useful:
* We can use FQ + EDT to implement efficient policies. Tx queues are picked by xps, ndo_select_queue of netdev driver, or skb hash in netdev_core_pick_tx(). In fact, the netdev driver, and skb hash are _not_ under control. xps uses the CPUs map to select Tx queues, but we can't figure out which task_struct of pod/containter running on this cpu in most case. We can use clsact filters to classify one pod/container traffic to one Tx queue. Why ?

In containter networking environment, there are two kinds of pod/ containter/net-namespace. One kind (e.g. P1, P2), the high throughput is key in these applications. But avoid running out of network resource, the outbound traffic of these pods is limited, using or sharing one dedicated Tx queues assigned HTB/TBF/FQ Qdisc. Other kind of pods (e.g. Pn), the low latency of data access is key. And the traffic is not limited. Pods use or share other dedicated Tx queues assigned FIFO Qdisc. This choice provides two benefits. First, contention on the HTB/FQ Qdisc lock is significantly reduced since fewer CPUs contend for the same queue. More importantly, Qdisc contention can be eliminated completely if each CPU has its own FIFO Qdisc for the second kind of pods.

There must be a mechanism in place to support classifying traffic based on pods/container to different Tx queues. Note that clsact is outside of Qdisc while Qdisc can run a classifier to select a sub-queue under the lock.

In general recording the decision in the skb seems a little heavy handed. This patch introduces a per-CPU variable, suggested by Eric.

The xmit.skip_txqueue flag is firstly cleared in __dev_queue_xmit().
- Tx Qdisc may install that skbedit actions, then xmit.skip_txqueue flag is set in qdisc->enqueue() though tx queue has been selected in netdev_tx_queue_mapping() or netdev_core_pick_tx(). That flag is cleared firstly in __dev_queue_xmit(), is useful:
- Avoid picking Tx queue with netdev_tx_queue_mapping() in next netdev in such case: eth0 macvlan - eth0.3 vlan - eth0 ixgbe-phy:
For example, eth0, macvlan in pod, which root Qdisc install skbedit queue_mapping, send packets to eth0.3, vlan in host. In __dev_queue_xmit() of eth0.3, clear the flag, does not select tx queue according to skb->queue_mapping because there is no filters in clsact or tx Qdisc of this netdev. Same action taked in eth0, ixgbe in Host.
- Avoid picking Tx queue for next packet. If we set xmit.skip_txqueue in tx Qdisc (qdisc->enqueue()), the proper way to clear it is clearing it in __dev_queue_xmit when processing next packets.

For performance reasons, use the static key. If user does not config the NET_EGRESS, the patch will not be compiled.

  +----+      +----+      +----+
  | P1 |      | P2 |      | Pn |
  +----+      +----+      +----+
    |           |           |
    +-----------+-----------+
                |
                | clsact/skbedit
                |      MQ

v
+-----------+-----------+
| q0 | q1 | qn
v v v
HTB/FQ HTB/FQ ... FIFO

Cc Jamal Hadi Salim <[email protected]>
Cc Cong Wang <[email protected]>
Cc Jiri Pirko <[email protected]>
Cc "David S. Miller" <[email protected]>
Cc Jakub Kicinski <[email protected]>
Cc Jonathan Lemon <[email protected]>
Cc Eric Dumazet <[email protected]>
Cc Alexander Lobakin <[email protected]>
Cc Paolo Abeni <[email protected]>
Cc Talal Ahmad <[email protected]>
Cc Kevin Hao <[email protected]>
Cc Ilias Apalodimas <[email protected]>
Cc Kees Cook <[email protected]>
Cc Kumar Kartikeya Dwivedi <[email protected]>
Cc Antoine Tenart <[email protected]>
Cc Wei Wang <[email protected]>
Cc Arnd Bergmann <[email protected]>
---
 include/linux/netdevice.h |  3 +++
 include/linux/rtnetlink.h |  1 +
 net/core/dev.c            | 31 +++++++++++++++++++++++++++++--
 net/sched/act_skbedit.c   |  6 +++++-
 4 files changed, 38 insertions(+), 3 deletions(-)
include/linux/netdevice.h +3 -0
index dadd4d2f6d8a..ac4094cf824a 100644
@@ -3015,6 +3015,9 @@ struct softnet_data {
 	struct {
 		u16 recursion;
 		u8  more;
+#ifdef CONFIG_NET_EGRESS
+		u8  skip_txqueue;
+#endif
 	} xmit;
 #ifdef CONFIG_RPS
 	/* input_queue_head should be written by cpu owning this struct,
include/linux/rtnetlink.h +1 -0
index bb9cb84114c1..e87c2dccc4d5 100644
@@ -100,6 +100,7 @@ void net_dec_ingress_queue(void);
 #ifdef CONFIG_NET_EGRESS
 void net_inc_egress_queue(void);
 void net_dec_egress_queue(void);
+void netdev_xmit_skip_txqueue(bool skip);
 #endif
 
 void rtnetlink_init(void);
net/core/dev.c +29 -2
index 5f1ac4812277..80dbbd5f6a73 100644
@@ -3860,6 +3860,25 @@ sch_handle_egress(struct sk_buff *skb, int *ret, struct net_device *dev)
 
 	return skb;
 }
+
+static struct netdev_queue *
+netdev_tx_queue_mapping(struct net_device *dev, struct sk_buff *skb)
+{
+	int qm = skb_get_queue_mapping(skb);
+
+	return netdev_get_tx_queue(dev, netdev_cap_txqueue(dev, qm));
+}
+
+static bool netdev_xmit_txqueue_skipped(void)
+{
+	return __this_cpu_read(softnet_data.xmit.skip_txqueue);
+}
+
+void netdev_xmit_skip_txqueue(bool skip)
+{
+	__this_cpu_write(softnet_data.xmit.skip_txqueue, skip);
+}
+EXPORT_SYMBOL_GPL(netdev_xmit_skip_txqueue);
 #endif /* CONFIG_NET_EGRESS */
 
 #ifdef CONFIG_XPS
@@ -4030,7 +4049,7 @@ struct netdev_queue *netdev_core_pick_tx(struct net_device *dev,
 static int __dev_queue_xmit(struct sk_buff *skb, struct net_device *sb_dev)
 {
 	struct net_device *dev = skb->dev;
-	struct netdev_queue *txq;
+	struct netdev_queue *txq = NULL;
 	struct Qdisc *q;
 	int rc = -ENOMEM;
 	bool again = false;
@@ -4058,11 +4077,17 @@ static int __dev_queue_xmit(struct sk_buff *skb, struct net_device *sb_dev)
 			if (!skb)
 				goto out;
 		}
+
+		netdev_xmit_skip_txqueue(false);
+
 		nf_skip_egress(skb, true);
 		skb = sch_handle_egress(skb, &rc, dev);
 		if (!skb)
 			goto out;
 		nf_skip_egress(skb, false);
+
+		if (netdev_xmit_txqueue_skipped())
+			txq = netdev_tx_queue_mapping(dev, skb);
 	}
 #endif
 	/* If device/qdisc don't need skb->dst, release it right now while
@@ -4073,7 +4098,9 @@ static int __dev_queue_xmit(struct sk_buff *skb, struct net_device *sb_dev)
 	else
 		skb_dst_force(skb);
 
-	txq = netdev_core_pick_tx(dev, skb, sb_dev);
+	if (!txq)
+		txq = netdev_core_pick_tx(dev, skb, sb_dev);
+
 	q = rcu_dereference_bh(txq->qdisc);
 
 	trace_net_dev_queue(skb);
net/sched/act_skbedit.c +5 -1
index ceba11b198bb..d5799b4fc499 100644
@@ -58,8 +58,12 @@ static int tcf_skbedit_act(struct sk_buff *skb, const struct tc_action *a,
 		}
 	}
 	if (params->flags & SKBEDIT_F_QUEUE_MAPPING &&
-	    skb->dev->real_num_tx_queues > params->queue_mapping)
+	    skb->dev->real_num_tx_queues > params->queue_mapping) {
+#ifdef CONFIG_NET_EGRESS
+		netdev_xmit_skip_txqueue(true);
+#endif
 		skb_set_queue_mapping(skb, params->queue_mapping);
+	}
 	if (params->flags & SKBEDIT_F_MARK) {
 		skb->mark &= ~params->mask;
 		skb->mark |= params->mark & params->mask;
Signature · 1 line
2.35.1
author maintainer
#33 lore raw

PATCH 34/135 cpuidle: PSCI: Improve support for suspend-to-RAM for PSCI OSI mode

In reply to Sasha Levin

From: Ulf Hansson <[email protected]>

[ Upstream commit 171b66e2e2e9d80b93c8cff799e6175074b22297 ]

When PSCI OSI mode is supported the syscore flag is set for the CPU devices that becomes attached to their PM domains (genpds). In the suspend-to-idle case, we call dev_pm_genpd_suspend|resume() to allow genpd to properly manage the power-off/on operations (pick an idlestate and manage the on/off notifications).

For suspend-to-ram, dev_pm_genpd_suspend|resume() is currently not being called, which causes a problem that the genpd on/off notifiers do not get sent as expected. This prevents the platform-specific operations from being executed, typically needed just before/after the boot CPU is being turned off/on.

To deal with this problem, let's register a syscore ops for cpuidle-psci when PSCI OSI mode is being used and call dev_pm_genpd_suspend|resume() from them. In this way, genpd regains control of the PM domain topology and then sends the on/off notifications when it's appropriate.

---
 drivers/cpuidle/cpuidle-psci.c | 46 ++++++++++++++++++++++++++++++++++
 1 file changed, 46 insertions(+)
drivers/cpuidle/cpuidle-psci.c +46 -0
index b51b5df08450..540105ca0781 100644
@@ -23,6 +23,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/string.h>
+#include <linux/syscore_ops.h>
 
 #include <asm/cpuidle.h>
 
@@ -131,6 +132,49 @@ static int psci_idle_cpuhp_down(unsigned int cpu)
 	return 0;
 }
 
+static void psci_idle_syscore_switch(bool suspend)
+{
+	bool cleared = false;
+	struct device *dev;
+	int cpu;
+
+	for_each_possible_cpu(cpu) {
+		dev = per_cpu_ptr(&psci_cpuidle_data, cpu)->dev;
+
+		if (dev && suspend) {
+			dev_pm_genpd_suspend(dev);
+		} else if (dev) {
+			dev_pm_genpd_resume(dev);
+
+			/* Account for userspace having offlined a CPU. */
+			if (pm_runtime_status_suspended(dev))
+				pm_runtime_set_active(dev);
+
+			/* Clear domain state to re-start fresh. */
+			if (!cleared) {
+				psci_set_domain_state(0);
+				cleared = true;
+			}
+		}
+	}
+}
+
+static int psci_idle_syscore_suspend(void)
+{
+	psci_idle_syscore_switch(true);
+	return 0;
+}
+
+static void psci_idle_syscore_resume(void)
+{
+	psci_idle_syscore_switch(false);
+}
+
+static struct syscore_ops psci_idle_syscore_ops = {
+	.suspend = psci_idle_syscore_suspend,
+	.resume = psci_idle_syscore_resume,
+};
+
 static void psci_idle_init_cpuhp(void)
 {
 	int err;
@@ -138,6 +182,8 @@ static void psci_idle_init_cpuhp(void)
 	if (!psci_cpuidle_use_cpuhp)
 		return;
 
+	register_syscore_ops(&psci_idle_syscore_ops);
+
 	err = cpuhp_setup_state_nocalls(CPUHP_AP_CPU_PM_STARTING,
 					"cpuidle/psci:online",
 					psci_idle_cpuhp_up,
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#34 lore raw

PATCH 35/135 drm/amd/pm: fix double free in si_parse_power_table()

In reply to Sasha Levin

From: Keita Suzuki <[email protected]>

[ Upstream commit f3fa2becf2fc25b6ac7cf8d8b1a2e4a86b3b72bd ]

In function si_parse_power_table(), array adev->pm.dpm.ps and its member is allocated. If the allocation of each member fails, the array itself is freed and returned with an error code. However, the array is later freed again in si_dpm_fini() function which is called when the function returns an error.

This leads to potential double free of the array adev->pm.dpm.ps, as well as leak of its array members, since the members are not freed in the allocation function and the array is not nulled when freed. In addition adev->pm.dpm.num_ps, which keeps track of the allocated array member, is not updated until the member allocation is successfully finished, this could also lead to either use after free, or uninitialized variable access in si_dpm_fini().

Fix this by postponing the free of the array until si_dpm_fini() and increment adev->pm.dpm.num_ps everytime the array member is allocated.

---
 drivers/gpu/drm/amd/pm/powerplay/si_dpm.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)
drivers/gpu/drm/amd/pm/powerplay/si_dpm.c +3 -5
index 81f82aa05ec2..66fc63f1f1c1 100644
@@ -7247,17 +7247,15 @@ static int si_parse_power_table(struct amdgpu_device *adev)
 	if (!adev->pm.dpm.ps)
 		return -ENOMEM;
 	power_state_offset = (u8 *)state_array->states;
-	for (i = 0; i < state_array->ucNumEntries; i++) {
+	for (adev->pm.dpm.num_ps = 0, i = 0; i < state_array->ucNumEntries; i++) {
 		u8 *idx;
 		power_state = (union pplib_power_state *)power_state_offset;
 		non_clock_array_index = power_state->v2.nonClockInfoIndex;
 		non_clock_info = (struct _ATOM_PPLIB_NONCLOCK_INFO *)
 			&non_clock_info_array->nonClockInfo[non_clock_array_index];
 		ps = kzalloc(sizeof(struct  si_ps), GFP_KERNEL);
-		if (ps == NULL) {
-			kfree(adev->pm.dpm.ps);
+		if (ps == NULL)
 			return -ENOMEM;
-		}
 		adev->pm.dpm.ps[i].ps_priv = ps;
 		si_parse_pplib_non_clock_info(adev, &adev->pm.dpm.ps[i],
 					      non_clock_info,
@@ -7279,8 +7277,8 @@ static int si_parse_power_table(struct amdgpu_device *adev)
 			k++;
 		}
 		power_state_offset += 2 + power_state->v2.ucNumDPMLevels;
+		adev->pm.dpm.num_ps++;
 	}
-	adev->pm.dpm.num_ps = state_array->ucNumEntries;
 
 	/* fill in the vce power states */
 	for (i = 0; i < adev->pm.dpm.num_of_vce_states; i++) {
Signature · 1 line
2.35.1
author maintainer
#35 lore raw

PATCH 36/135 ASoC: rsnd: care default case on rsnd_ssiu_busif_err_status_clear()

In reply to Sasha Levin

From: Kuninori Morimoto <[email protected]>

[ Upstream commit b1384d4c95088d01f4266237faabf165d3d605fc ]

commit cfb7b8bf1e2d66 ("ASoC: rsnd: tidyup rsnd_ssiu_busif_err_status_clear()") merged duplicate code, but it didn't care about default case, and causes smatch warnings.

smatch warnings:
sound/soc/sh/rcar/ssiu.c:112 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'offset'.
sound/soc/sh/rcar/ssiu.c:114 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'shift'.

This patch cares it.

---
 sound/soc/sh/rcar/ssiu.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
sound/soc/sh/rcar/ssiu.c +3 -1
index 0d8f97633dd2..138f95dd9f4a 100644
@@ -102,6 +102,8 @@ bool rsnd_ssiu_busif_err_status_clear(struct rsnd_mod *mod)
 		shift  = 1;
 		offset = 1;
 		break;
+	default:
+		goto out;
 	}
 
 	for (i = 0; i < 4; i++) {
@@ -120,7 +122,7 @@ bool rsnd_ssiu_busif_err_status_clear(struct rsnd_mod *mod)
 		}
 		rsnd_mod_write(mod, reg, val);
 	}
-
+out:
 	return error;
 }
 
Signature · 1 line
2.35.1
author maintainer
#36 lore raw

PATCH 37/135 ASoC: rsnd: care return value from rsnd_node_fixed_index()

In reply to Sasha Levin

From: Kuninori Morimoto <[email protected]>

[ Upstream commit d09a7db431c65aaa8303eb456439d1831ca2e6b4 ]

Renesas Sound is very complex, and thus it needs to use rsnd_node_fixed_index() to know enabled pin index.

It returns error if strange pin was selected, but some codes didn't check it.

This patch 1) indicates error message, 2) check return value.

---
 sound/soc/sh/rcar/core.c | 15 ++++++++++-----
 sound/soc/sh/rcar/dma.c  |  9 ++++++++-
 sound/soc/sh/rcar/rsnd.h |  2 +-
 sound/soc/sh/rcar/src.c  |  7 ++++++-
 sound/soc/sh/rcar/ssi.c  | 14 ++++++++++++--
 sound/soc/sh/rcar/ssiu.c |  7 ++++++-
 6 files changed, 43 insertions(+), 11 deletions(-)
sound/soc/sh/rcar/core.c +10 -5
index 6a8fe0da7670..af8ef2a27d34 100644
@@ -1159,6 +1159,7 @@ void rsnd_parse_connect_common(struct rsnd_dai *rdai, char *name,
 		struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *np;
 	int i;
 
@@ -1169,7 +1170,11 @@ void rsnd_parse_connect_common(struct rsnd_dai *rdai, char *name,
 	for_each_child_of_node(node, np) {
 		struct rsnd_mod *mod;
 
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
+		if (i < 0) {
+			of_node_put(np);
+			break;
+		}
 
 		mod = mod_get(priv, i);
 
@@ -1183,7 +1188,7 @@ void rsnd_parse_connect_common(struct rsnd_dai *rdai, char *name,
 	of_node_put(node);
 }
 
-int rsnd_node_fixed_index(struct device_node *node, char *name, int idx)
+int rsnd_node_fixed_index(struct device *dev, struct device_node *node, char *name, int idx)
 {
 	char node_name[16];
 
@@ -1210,6 +1215,8 @@ int rsnd_node_fixed_index(struct device_node *node, char *name, int idx)
 			return idx;
 	}
 
+	dev_err(dev, "strange node numbering (%s)",
+		of_node_full_name(node));
 	return -EINVAL;
 }
 
@@ -1221,10 +1228,8 @@ int rsnd_node_count(struct rsnd_priv *priv, struct device_node *node, char *name
 
 	i = 0;
 	for_each_child_of_node(node, np) {
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
 		if (i < 0) {
-			dev_err(dev, "strange node numbering (%s)",
-				of_node_full_name(node));
 			of_node_put(np);
 			return 0;
 		}
sound/soc/sh/rcar/dma.c +8 -1
index 03e0d4eca781..463ab237d7bd 100644
@@ -240,12 +240,19 @@ static int rsnd_dmaen_start(struct rsnd_mod *mod,
 struct dma_chan *rsnd_dma_request_channel(struct device_node *of_node, char *name,
 					  struct rsnd_mod *mod, char *x)
 {
+	struct rsnd_priv *priv = rsnd_mod_to_priv(mod);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct dma_chan *chan = NULL;
 	struct device_node *np;
 	int i = 0;
 
 	for_each_child_of_node(of_node, np) {
-		i = rsnd_node_fixed_index(np, name, i);
+		i = rsnd_node_fixed_index(dev, np, name, i);
+		if (i < 0) {
+			chan = NULL;
+			of_node_put(np);
+			break;
+		}
 
 		if (i == rsnd_mod_id_raw(mod) && (!chan))
 			chan = of_dma_request_slave_channel(np, x);
sound/soc/sh/rcar/rsnd.h +1 -1
index 6580bab0e229..d9cd190d7e19 100644
@@ -460,7 +460,7 @@ void rsnd_parse_connect_common(struct rsnd_dai *rdai, char *name,
 		struct device_node *playback,
 		struct device_node *capture);
 int rsnd_node_count(struct rsnd_priv *priv, struct device_node *node, char *name);
-int rsnd_node_fixed_index(struct device_node *node, char *name, int idx);
+int rsnd_node_fixed_index(struct device *dev, struct device_node *node, char *name, int idx);
 
 int rsnd_channel_normalization(int chan);
 #define rsnd_runtime_channel_original(io) \
sound/soc/sh/rcar/src.c +6 -1
index 42a100c6303d..0ea84ae57c6a 100644
@@ -676,7 +676,12 @@ int rsnd_src_probe(struct rsnd_priv *priv)
 		if (!of_device_is_available(np))
 			goto skip;
 
-		i = rsnd_node_fixed_index(np, SRC_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SRC_NAME, i);
+		if (i < 0) {
+			ret = -EINVAL;
+			of_node_put(np);
+			goto rsnd_src_probe_done;
+		}
 
 		src = rsnd_src_get(priv, i);
 
sound/soc/sh/rcar/ssi.c +12 -2
index 87e606f688d3..43c5e27dc5c8 100644
@@ -1105,6 +1105,7 @@ void rsnd_parse_connect_ssi(struct rsnd_dai *rdai,
 			    struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *node;
 	struct device_node *np;
 	int i;
@@ -1117,7 +1118,11 @@ void rsnd_parse_connect_ssi(struct rsnd_dai *rdai,
 	for_each_child_of_node(node, np) {
 		struct rsnd_mod *mod;
 
-		i = rsnd_node_fixed_index(np, SSI_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SSI_NAME, i);
+		if (i < 0) {
+			of_node_put(np);
+			break;
+		}
 
 		mod = rsnd_ssi_mod_get(priv, i);
 
@@ -1182,7 +1187,12 @@ int rsnd_ssi_probe(struct rsnd_priv *priv)
 		if (!of_device_is_available(np))
 			goto skip;
 
-		i = rsnd_node_fixed_index(np, SSI_NAME, i);
+		i = rsnd_node_fixed_index(dev, np, SSI_NAME, i);
+		if (i < 0) {
+			ret = -EINVAL;
+			of_node_put(np);
+			goto rsnd_ssi_probe_done;
+		}
 
 		ssi = rsnd_ssi_get(priv, i);
 
sound/soc/sh/rcar/ssiu.c +6 -1
index 138f95dd9f4a..4b8a63e336c7 100644
@@ -462,6 +462,7 @@ void rsnd_parse_connect_ssiu(struct rsnd_dai *rdai,
 			     struct device_node *capture)
 {
 	struct rsnd_priv *priv = rsnd_rdai_to_priv(rdai);
+	struct device *dev = rsnd_priv_to_dev(priv);
 	struct device_node *node = rsnd_ssiu_of_node(priv);
 	struct rsnd_dai_stream *io_p = &rdai->playback;
 	struct rsnd_dai_stream *io_c = &rdai->capture;
@@ -474,7 +475,11 @@ void rsnd_parse_connect_ssiu(struct rsnd_dai *rdai,
 		for_each_child_of_node(node, np) {
 			struct rsnd_mod *mod;
 
-			i = rsnd_node_fixed_index(np, SSIU_NAME, i);
+			i = rsnd_node_fixed_index(dev, np, SSIU_NAME, i);
+			if (i < 0) {
+				of_node_put(np);
+				break;
+			}
 
 			mod = rsnd_ssiu_mod_get(priv, i);
 
Signature · 1 line
2.35.1
author maintainer
#37 lore raw

PATCH 38/135 ath9k: fix QCA9561 PA bias level

In reply to Sasha Levin

From: Thibaut VARÈNE <[email protected]>

[ Upstream commit e999a5da28a0e0f7de242d841ef7d5e48f4646ae ]

This patch fixes an invalid TX PA DC bias level on QCA9561, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs).

This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is wrong for 9561."

In real life testing, without this patch the 2.4GHz throughput on Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to practical maximum with the patch applied.

[1] https://lore.kernel.org/all/[email protected]

---
 drivers/net/wireless/ath/ath9k/ar9003_phy.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/ath9k/ar9003_phy.h +1 -1
index a171dbb29fbb..ad949eb02f3d 100644
@@ -720,7 +720,7 @@
 #define AR_CH0_TOP2		(AR_SREV_9300(ah) ? 0x1628c : \
 					(AR_SREV_9462(ah) ? 0x16290 : 0x16284))
 #define AR_CH0_TOP2_XPABIASLVL		(AR_SREV_9561(ah) ? 0x1e00 : 0xf000)
-#define AR_CH0_TOP2_XPABIASLVL_S	12
+#define AR_CH0_TOP2_XPABIASLVL_S	(AR_SREV_9561(ah) ? 9 : 12)
 
 #define AR_CH0_XTAL		(AR_SREV_9300(ah) ? 0x16294 : \
 				 ((AR_SREV_9462(ah) || AR_SREV_9565(ah)) ? 0x16298 : \
Signature · 1 line
2.35.1
author maintainer
#38 lore raw

PATCH 39/135 media: Revert "media: dw9768: activate runtime PM and turn off device"

In reply to Sasha Levin

From: Sakari Ailus <[email protected]>

[ Upstream commit 7dd0f93a31af03cba81c684c4c361bba510ffe71 ]

This reverts commit c09d776eaa060534a1663e3b89d842db3e1d9076.

Revert the commit as it breaks runtime PM support on OF based systems. More fixes to the driver are needed.

---
 drivers/media/i2c/dw9768.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/media/i2c/dw9768.c +0 -6
index 65c6acf3ced9..c086580efac7 100644
@@ -469,11 +469,6 @@ static int dw9768_probe(struct i2c_client *client)
 
 	dw9768->sd.entity.function = MEDIA_ENT_F_LENS;
 
-	/*
-	 * Device is already turned on by i2c-core with ACPI domain PM.
-	 * Attempt to turn off the device to satisfy the privacy LED concerns.
-	 */
-	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
 	if (!pm_runtime_enabled(dev)) {
 		ret = dw9768_runtime_resume(dev);
@@ -488,7 +483,6 @@ static int dw9768_probe(struct i2c_client *client)
 		dev_err(dev, "failed to register V4L2 subdev: %d", ret);
 		goto err_power_off;
 	}
-	pm_runtime_idle(dev);
 
 	return 0;
 
Signature · 1 line
2.35.1
author maintainer
#39 lore raw

PATCH 40/135 media: venus: hfi: avoid null dereference in deinit

In reply to Sasha Levin

From: Luca Weiss <[email protected]>

[ Upstream commit 86594f6af867b5165d2ba7b5a71fae3a5961e56c ]

If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore.

Avoid this null pointer derefence by skipping the call when necessary.

---
 drivers/media/platform/qcom/venus/hfi.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/platform/qcom/venus/hfi.c +3 -0
index 4e2151fb47f0..1968f09ad177 100644
@@ -104,6 +104,9 @@ int hfi_core_deinit(struct venus_core *core, bool blocking)
 		mutex_lock(&core->lock);
 	}
 
+	if (!core->ops)
+		goto unlock;
+
 	ret = core->ops->core_deinit(core);
 
 	if (!ret)
Signature · 1 line
2.35.1
author maintainer
#40 lore raw

PATCH 41/135 media: venus: do not queue internal buffers from previous sequence

In reply to Sasha Levin

From: Vikash Garodia <[email protected]>

[ Upstream commit 73664f107c0fafb59cd91e576b81c986adb74610 ]

During reconfig (DRC) event from firmware, it is not guaranteed that all the DPB(internal) buffers would be released by the firmware. Some buffers might be released gradually while processing frames from the new sequence. These buffers now stay idle in the dpblist. In subsequent call to queue the DPBs to firmware, these idle buffers should not be queued. The fix identifies those buffers and free them.

---
 drivers/media/platform/qcom/venus/helpers.c | 34 +++++++++++++++------
 1 file changed, 25 insertions(+), 9 deletions(-)
drivers/media/platform/qcom/venus/helpers.c +25 -9
index 0bca95d01650..fa01edd54c03 100644
@@ -90,12 +90,28 @@ bool venus_helper_check_codec(struct venus_inst *inst, u32 v4l2_pixfmt)
 }
 EXPORT_SYMBOL_GPL(venus_helper_check_codec);
 
+static void free_dpb_buf(struct venus_inst *inst, struct intbuf *buf)
+{
+	ida_free(&inst->dpb_ids, buf->dpb_out_tag);
+
+	list_del_init(&buf->list);
+	dma_free_attrs(inst->core->dev, buf->size, buf->va, buf->da,
+		       buf->attrs);
+	kfree(buf);
+}
+
 int venus_helper_queue_dpb_bufs(struct venus_inst *inst)
 {
-	struct intbuf *buf;
+	struct intbuf *buf, *next;
+	unsigned int dpb_size = 0;
 	int ret = 0;
 
-	list_for_each_entry(buf, &inst->dpbbufs, list) {
+	if (inst->dpb_buftype == HFI_BUFFER_OUTPUT)
+		dpb_size = inst->output_buf_size;
+	else if (inst->dpb_buftype == HFI_BUFFER_OUTPUT2)
+		dpb_size = inst->output2_buf_size;
+
+	list_for_each_entry_safe(buf, next, &inst->dpbbufs, list) {
 		struct hfi_frame_data fdata;
 
 		memset(&fdata, 0, sizeof(fdata));
@@ -106,6 +122,12 @@ int venus_helper_queue_dpb_bufs(struct venus_inst *inst)
 		if (buf->owned_by == FIRMWARE)
 			continue;
 
+		/* free buffer from previous sequence which was released later */
+		if (dpb_size > buf->size) {
+			free_dpb_buf(inst, buf);
+			continue;
+		}
+
 		fdata.clnt_data = buf->dpb_out_tag;
 
 		ret = hfi_session_process_buf(inst, &fdata);
@@ -127,13 +149,7 @@ int venus_helper_free_dpb_bufs(struct venus_inst *inst)
 	list_for_each_entry_safe(buf, n, &inst->dpbbufs, list) {
 		if (buf->owned_by == FIRMWARE)
 			continue;
-
-		ida_free(&inst->dpb_ids, buf->dpb_out_tag);
-
-		list_del_init(&buf->list);
-		dma_free_attrs(inst->core->dev, buf->size, buf->va, buf->da,
-			       buf->attrs);
-		kfree(buf);
+		free_dpb_buf(inst, buf);
 	}
 
 	if (list_empty(&inst->dpbbufs))
Signature · 1 line
2.35.1
author maintainer
#41 lore raw

PATCH 42/135 media: pci: cx23885: Fix the error handling in cx23885_initdev()

In reply to Sasha Levin

From: Zheyu Ma <[email protected]>

[ Upstream commit e8123311cf06d7dae71e8c5fe78e0510d20cd30b ]

When the driver fails to call the dma_set_mask(), the driver will get the following splat:

[   55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[   55.854486] Read of size 8 at addr ffff88810de60408 by task modprobe/590
[   55.856822] Call Trace:
[   55.860327]  __process_removed_driver+0x3c/0x240
[   55.861347]  bus_for_each_dev+0x102/0x160
[   55.861681]  i2c_del_driver+0x2f/0x50

This is because the driver has initialized the i2c related resources in cx23885_dev_setup() but not released them in error handling, fix this bug by modifying the error path that jumps after failing to call the dma_set_mask().

---
 drivers/media/pci/cx23885/cx23885-core.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/media/pci/cx23885/cx23885-core.c +3 -3
index f8f2ff3b00c3..a07b18f2034e 100644
@@ -2165,7 +2165,7 @@ static int cx23885_initdev(struct pci_dev *pci_dev,
 	err = dma_set_mask(&pci_dev->dev, 0xffffffff);
 	if (err) {
 		pr_err("%s/0: Oops: no 32bit PCI DMA ???\n", dev->name);
-		goto fail_ctrl;
+		goto fail_dma_set_mask;
 	}
 
 	err = request_irq(pci_dev->irq, cx23885_irq,
@@ -2173,7 +2173,7 @@ static int cx23885_initdev(struct pci_dev *pci_dev,
 	if (err < 0) {
 		pr_err("%s: can't get IRQ %d\n",
 		       dev->name, pci_dev->irq);
-		goto fail_irq;
+		goto fail_dma_set_mask;
 	}
 
 	switch (dev->board) {
@@ -2195,7 +2195,7 @@ static int cx23885_initdev(struct pci_dev *pci_dev,
 
 	return 0;
 
-fail_irq:
+fail_dma_set_mask:
 	cx23885_dev_unregister(dev);
 fail_ctrl:
 	v4l2_ctrl_handler_free(hdl);
Signature · 1 line
2.35.1
author maintainer
#42 lore raw

PATCH 43/135 media: cx25821: Fix the warning when removing the module

In reply to Sasha Levin

From: Zheyu Ma <[email protected]>

[ Upstream commit 2203436a4d24302871617373a7eb21bc17e38762 ]

When removing the module, we will get the following warning:

[   14.746697] remove_proc_entry: removing non-empty directory 'irq/21', leaking at least 'cx25821[1]'
[   14.747449] WARNING: CPU: 4 PID: 368 at fs/proc/generic.c:717 remove_proc_entry+0x389/0x3f0
[   14.751611] RIP: 0010:remove_proc_entry+0x389/0x3f0
[   14.759589] Call Trace:
[   14.759792]  <TASK>
[   14.759975]  unregister_irq_proc+0x14c/0x170
[   14.760340]  irq_free_descs+0x94/0xe0
[   14.760640]  mp_unmap_irq+0xb6/0x100
[   14.760937]  acpi_unregister_gsi_ioapic+0x27/0x40
[   14.761334]  acpi_pci_irq_disable+0x1d3/0x320
[   14.761688]  pci_disable_device+0x1ad/0x380
[   14.762027]  ? _raw_spin_unlock_irqrestore+0x2d/0x60
[   14.762442]  ? cx25821_shutdown+0x20/0x9f0 [cx25821]
[   14.762848]  cx25821_finidev+0x48/0xc0 [cx25821]
[   14.763242]  pci_device_remove+0x92/0x240

Fix this by freeing the irq before call pci_disable_device().

---
 drivers/media/pci/cx25821/cx25821-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/pci/cx25821/cx25821-core.c +1 -1
index 3078a39f0b95..6627fa9166d3 100644
@@ -1332,11 +1332,11 @@ static void cx25821_finidev(struct pci_dev *pci_dev)
 	struct cx25821_dev *dev = get_cx25821(v4l2_dev);
 
 	cx25821_shutdown(dev);
-	pci_disable_device(pci_dev);
 
 	/* unregister stuff */
 	if (pci_dev->irq)
 		free_irq(pci_dev->irq, dev);
+	pci_disable_device(pci_dev);
 
 	cx25821_dev_unregister(dev);
 	v4l2_device_unregister(v4l2_dev);
Signature · 1 line
2.35.1
author maintainer
#43 lore raw

PATCH 44/135 md/bitmap: don't set sb values if can't pass sanity check

In reply to Sasha Levin

From: Heming Zhao <[email protected]>

[ Upstream commit e68cb83a57a458b01c9739e2ad9cb70b04d1e6d2 ]

If bitmap area contains invalid data, kernel will crash then mdadm triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will handle broken metadata case. In clustered array, only kernel space handles bitmap slot info. But even this bug only happened in clustered env, current sanity check is wrong, the code should be changed.

How to trigger: (faulty injection)

dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sda
dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sdb mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb mdadm -Ss
echo aaa > magic.txt
== below modifying slot 2 bitmap data ==
dd if=magic.txt of=/dev/sda seek=16384 bs=1 count=3 <== destroy magic dd if=/dev/zero of=/dev/sda seek=16436 bs=1 count=4 <== ZERO chunksize mdadm -A /dev/md0 /dev/sda /dev/sdb
== kernel crashes. mdadm outputs "Segmentation fault" ==

Reason of kernel crash:

In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T() trigger "divide error".

Crash log:

kernel: md: md0 stopped.
kernel: md/raid1:md0: not clean -- starting background reconstruction
kernel: md/raid1:md0: active with 2 out of 2 mirrors
kernel: dlm: ... ...
kernel: md-cluster: Joined cluster 44810aba-38bb-e6b8-daca-bc97a0b254aa slot 1
kernel: md0: invalid bitmap file superblock: bad magic
kernel: md_bitmap_copy_from_slot can't get bitmap from slot 2
kernel: md-cluster: Could not gather bitmaps from slot 2
kernel: divide error: 0000 [#1] SMP NOPTI
kernel: CPU: 0 PID: 1603 Comm: mdadm Not tainted 5.14.6-1-default
kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]
kernel: RSP: 0018:ffffc22ac0843ba0 EFLAGS: 00010246
kernel: ... ...
kernel: Call Trace:
kernel:  ? dlm_lock_sync+0xd0/0xd0 [md_cluster 77fe..7a0]
kernel:  md_bitmap_copy_from_slot+0x2c/0x290 [md_mod 24ea..d3a]
kernel:  load_bitmaps+0xec/0x210 [md_cluster 77fe..7a0]
kernel:  md_bitmap_load+0x81/0x1e0 [md_mod 24ea..d3a]
kernel:  do_md_run+0x30/0x100 [md_mod 24ea..d3a]
kernel:  md_ioctl+0x1290/0x15a0 [md_mod 24ea....d3a]
kernel:  ? mddev_unlock+0xaa/0x130 [md_mod 24ea..d3a]
kernel:  ? blkdev_ioctl+0xb1/0x2b0
kernel:  block_ioctl+0x3b/0x40
kernel:  __x64_sys_ioctl+0x7f/0xb0
kernel:  do_syscall_64+0x59/0x80
kernel:  ? exit_to_user_mode_prepare+0x1ab/0x230
kernel:  ? syscall_exit_to_user_mode+0x18/0x40
kernel:  ? do_syscall_64+0x69/0x80
kernel:  entry_SYSCALL_64_after_hwframe+0x44/0xae
kernel: RIP: 0033:0x7f4a15fa722b
kernel: ... ...
kernel: ---[ end trace 8afa7612f559c868 ]---
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]
---
 drivers/md/md-bitmap.c | 44 ++++++++++++++++++++++--------------------
 1 file changed, 23 insertions(+), 21 deletions(-)
drivers/md/md-bitmap.c +23 -21
index bfd6026d7809..612460d2bdaf 100644
@@ -639,14 +639,6 @@ static int md_bitmap_read_sb(struct bitmap *bitmap)
 	daemon_sleep = le32_to_cpu(sb->daemon_sleep) * HZ;
 	write_behind = le32_to_cpu(sb->write_behind);
 	sectors_reserved = le32_to_cpu(sb->sectors_reserved);
-	/* Setup nodes/clustername only if bitmap version is
-	 * cluster-compatible
-	 */
-	if (sb->version == cpu_to_le32(BITMAP_MAJOR_CLUSTERED)) {
-		nodes = le32_to_cpu(sb->nodes);
-		strlcpy(bitmap->mddev->bitmap_info.cluster_name,
-				sb->cluster_name, 64);
-	}
 
 	/* verify that the bitmap-specific fields are valid */
 	if (sb->magic != cpu_to_le32(BITMAP_MAGIC))
@@ -668,6 +660,16 @@ static int md_bitmap_read_sb(struct bitmap *bitmap)
 		goto out;
 	}
 
+	/*
+	 * Setup nodes/clustername only if bitmap version is
+	 * cluster-compatible
+	 */
+	if (sb->version == cpu_to_le32(BITMAP_MAJOR_CLUSTERED)) {
+		nodes = le32_to_cpu(sb->nodes);
+		strlcpy(bitmap->mddev->bitmap_info.cluster_name,
+				sb->cluster_name, 64);
+	}
+
 	/* keep the array size field of the bitmap superblock up to date */
 	sb->sync_size = cpu_to_le64(bitmap->mddev->resync_max_sectors);
 
@@ -700,9 +702,9 @@ static int md_bitmap_read_sb(struct bitmap *bitmap)
 
 out:
 	kunmap_atomic(sb);
-	/* Assigning chunksize is required for "re_read" */
-	bitmap->mddev->bitmap_info.chunksize = chunksize;
 	if (err == 0 && nodes && (bitmap->cluster_slot < 0)) {
+		/* Assigning chunksize is required for "re_read" */
+		bitmap->mddev->bitmap_info.chunksize = chunksize;
 		err = md_setup_cluster(bitmap->mddev, nodes);
 		if (err) {
 			pr_warn("%s: Could not setup cluster service (%d)\n",
@@ -713,18 +715,18 @@ static int md_bitmap_read_sb(struct bitmap *bitmap)
 		goto re_read;
 	}
 
-
 out_no_sb:
-	if (test_bit(BITMAP_STALE, &bitmap->flags))
-		bitmap->events_cleared = bitmap->mddev->events;
-	bitmap->mddev->bitmap_info.chunksize = chunksize;
-	bitmap->mddev->bitmap_info.daemon_sleep = daemon_sleep;
-	bitmap->mddev->bitmap_info.max_write_behind = write_behind;
-	bitmap->mddev->bitmap_info.nodes = nodes;
-	if (bitmap->mddev->bitmap_info.space == 0 ||
-	    bitmap->mddev->bitmap_info.space > sectors_reserved)
-		bitmap->mddev->bitmap_info.space = sectors_reserved;
-	if (err) {
+	if (err == 0) {
+		if (test_bit(BITMAP_STALE, &bitmap->flags))
+			bitmap->events_cleared = bitmap->mddev->events;
+		bitmap->mddev->bitmap_info.chunksize = chunksize;
+		bitmap->mddev->bitmap_info.daemon_sleep = daemon_sleep;
+		bitmap->mddev->bitmap_info.max_write_behind = write_behind;
+		bitmap->mddev->bitmap_info.nodes = nodes;
+		if (bitmap->mddev->bitmap_info.space == 0 ||
+			bitmap->mddev->bitmap_info.space > sectors_reserved)
+			bitmap->mddev->bitmap_info.space = sectors_reserved;
+	} else {
 		md_bitmap_print_sb(bitmap);
 		if (bitmap->cluster_slot < 0)
 			md_cluster_stop(bitmap->mddev);
Signature · 1 line
2.35.1
author maintainer
#44 lore raw

PATCH 45/135 mmc: jz4740: Apply DMA engine limits to maximum segment size

In reply to Sasha Levin

From: Aidan MacDonald <[email protected]>

[ Upstream commit afadb04f1d6e74b18a253403f5274cde5e3fd7bd ]

Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and limit the maximum segment size based on the DMA engine's capabilities. This is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 21 at kernel/dma/debug.c:1162 debug_dma_map_sg+0x2f4/0x39c
DMA-API: jz4780-dma 13420000.dma-controller: mapping sg segment longer than device claims to support [len=98304] [max=65536]
CPU: 0 PID: 21 Comm: kworker/0:1H Not tainted 5.18.0-rc1 #19
Workqueue: kblockd blk_mq_run_work_fn
Stack : 81575aec 00000004 80620000 80620000 80620000 805e7358 00000009 801537ac
        814c832c 806276e3 806e34b4 80620000 81575aec 00000001 81575ab8 09291444
        00000000 00000000 805e7358 81575958 ffffffea 8157596c 00000000 636f6c62
        6220646b 80387a70 0000000f 6d5f6b6c 80620000 00000000 81575ba4 00000009
        805e170c 80896640 00000001 00010000 00000000 00000000 00006098 806e0000
        ...
Call Trace:
[<80107670>] show_stack+0x84/0x120
[<80528cd8>] __warn+0xb8/0xec
[<80528d78>] warn_slowpath_fmt+0x6c/0xb8
[<8016f1d4>] debug_dma_map_sg+0x2f4/0x39c
[<80169d4c>] __dma_map_sg_attrs+0xf0/0x118
[<8016a27c>] dma_map_sg_attrs+0x14/0x28
[<804f66b4>] jz4740_mmc_prepare_dma_data+0x74/0xa4
[<804f6714>] jz4740_mmc_pre_request+0x30/0x54
[<804f4ff4>] mmc_blk_mq_issue_rq+0x6e0/0x7bc
[<804f5590>] mmc_mq_queue_rq+0x220/0x2d4
[<8038b2c0>] blk_mq_dispatch_rq_list+0x480/0x664
[<80391040>] blk_mq_do_dispatch_sched+0x2dc/0x370
[<80391468>] __blk_mq_sched_dispatch_requests+0xec/0x164
[<80391540>] blk_mq_sched_dispatch_requests+0x44/0x94
[<80387900>] __blk_mq_run_hw_queue+0xb0/0xcc
[<80134c14>] process_one_work+0x1b8/0x264
[<80134ff8>] worker_thread+0x2ec/0x3b8
[<8013b13c>] kthread+0x104/0x10c
[<80101dcc>] ret_from_kernel_thread+0x14/0x1c

---[ end trace 0000000000000000 ]---
---
 drivers/mmc/host/jz4740_mmc.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
drivers/mmc/host/jz4740_mmc.c +20 -0
index 7ab1b38a7be5..b1d563b2ed1b 100644
@@ -247,6 +247,26 @@ static int jz4740_mmc_acquire_dma_channels(struct jz4740_mmc_host *host)
 		return PTR_ERR(host->dma_rx);
 	}
 
+	/*
+	 * Limit the maximum segment size in any SG entry according to
+	 * the parameters of the DMA engine device.
+	 */
+	if (host->dma_tx) {
+		struct device *dev = host->dma_tx->device->dev;
+		unsigned int max_seg_size = dma_get_max_seg_size(dev);
+
+		if (max_seg_size < host->mmc->max_seg_size)
+			host->mmc->max_seg_size = max_seg_size;
+	}
+
+	if (host->dma_rx) {
+		struct device *dev = host->dma_rx->device->dev;
+		unsigned int max_seg_size = dma_get_max_seg_size(dev);
+
+		if (max_seg_size < host->mmc->max_seg_size)
+			host->mmc->max_seg_size = max_seg_size;
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#45 lore raw

PATCH 46/135 drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit

In reply to Sasha Levin

From: Vignesh Raghavendra <[email protected]>

[ Upstream commit c7666240ec76422cb7546bd07cc8ae80dc0ccdd2 ]

The ARASAN MMC controller on Keystone 3 class of devices need the SDCD line to be connected for proper functioning. Similar to the issue pointed out in sdhci-of-arasan.c driver, commit 3794c542641f ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").

In cases where this can't be connected, add a quirk to force the controller into test mode and set the TESTCD bit. Use the flag "ti,fails-without-test-cd", to implement this above quirk when required.

---
 drivers/mmc/host/sdhci_am654.c | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)
drivers/mmc/host/sdhci_am654.c +22 -1
index b4891bb26648..a3e62e212631 100644
@@ -147,6 +147,9 @@ struct sdhci_am654_data {
 	int drv_strength;
 	int strb_sel;
 	u32 flags;
+	u32 quirks;
+
+#define SDHCI_AM654_QUIRK_FORCE_CDTEST BIT(0)
 };
 
 struct sdhci_am654_driver_data {
@@ -369,6 +372,21 @@ static void sdhci_am654_write_b(struct sdhci_host *host, u8 val, int reg)
 	}
 }
 
+static void sdhci_am654_reset(struct sdhci_host *host, u8 mask)
+{
+	u8 ctrl;
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_am654_data *sdhci_am654 = sdhci_pltfm_priv(pltfm_host);
+
+	sdhci_reset(host, mask);
+
+	if (sdhci_am654->quirks & SDHCI_AM654_QUIRK_FORCE_CDTEST) {
+		ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
+		ctrl |= SDHCI_CTRL_CDTEST_INS | SDHCI_CTRL_CDTEST_EN;
+		sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
+	}
+}
+
 static int sdhci_am654_execute_tuning(struct mmc_host *mmc, u32 opcode)
 {
 	struct sdhci_host *host = mmc_priv(mmc);
@@ -500,7 +518,7 @@ static struct sdhci_ops sdhci_j721e_4bit_ops = {
 	.set_clock = sdhci_j721e_4bit_set_clock,
 	.write_b = sdhci_am654_write_b,
 	.irq = sdhci_am654_cqhci_irq,
-	.reset = sdhci_reset,
+	.reset = sdhci_am654_reset,
 };
 
 static const struct sdhci_pltfm_data sdhci_j721e_4bit_pdata = {
@@ -719,6 +737,9 @@ static int sdhci_am654_get_of_property(struct platform_device *pdev,
 	device_property_read_u32(dev, "ti,clkbuf-sel",
 				 &sdhci_am654->clkbuf_sel);
 
+	if (device_property_read_bool(dev, "ti,fails-without-test-cd"))
+		sdhci_am654->quirks |= SDHCI_AM654_QUIRK_FORCE_CDTEST;
+
 	sdhci_get_of_property(pdev);
 
 	return 0;
Signature · 1 line
2.35.1
author maintainer
#46 lore raw

PATCH 47/135 drm/sun4i: Add support for D1 TCONs

In reply to Sasha Levin

From: Samuel Holland <[email protected]>

[ Upstream commit b9b52d2f4aafa2bd637ace0f24615bdad8e49f01 ]

D1 has a TCON TOP, so its quirks are similar to those for the R40 TCONs. While there are some register changes, the part of the TCON TV supported by the driver matches the R40 quirks, so that quirks structure can be reused. D1 has the first supported TCON LCD with a TCON TOP, so the TCON LCD needs a new quirks structure.

D1's TCON LCD hardware supports LVDS; in fact it provides dual-link LVDS from a single TCON. However, it comes with a brand new LVDS PHY. Since this PHY has not been tested, leave out LVDS driver support for now.

---
 drivers/gpu/drm/sun4i/sun4i_tcon.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/gpu/drm/sun4i/sun4i_tcon.c +8 -0
index 88db2d2a9336..2ee158aaeb9e 100644
@@ -1542,6 +1542,12 @@ static const struct sun4i_tcon_quirks sun9i_a80_tcon_tv_quirks = {
 	.needs_edp_reset = true,
 };
 
+static const struct sun4i_tcon_quirks sun20i_d1_lcd_quirks = {
+	.has_channel_0		= true,
+	.dclk_min_div		= 1,
+	.set_mux		= sun8i_r40_tcon_tv_set_mux,
+};
+
 /* sun4i_drv uses this list to check if a device node is a TCON */
 const struct of_device_id sun4i_tcon_of_table[] = {
 	{ .compatible = "allwinner,sun4i-a10-tcon", .data = &sun4i_a10_quirks },
@@ -1559,6 +1565,8 @@ const struct of_device_id sun4i_tcon_of_table[] = {
 	{ .compatible = "allwinner,sun8i-v3s-tcon", .data = &sun8i_v3s_quirks },
 	{ .compatible = "allwinner,sun9i-a80-tcon-lcd", .data = &sun9i_a80_tcon_lcd_quirks },
 	{ .compatible = "allwinner,sun9i-a80-tcon-tv", .data = &sun9i_a80_tcon_tv_quirks },
+	{ .compatible = "allwinner,sun20i-d1-tcon-lcd", .data = &sun20i_d1_lcd_quirks },
+	{ .compatible = "allwinner,sun20i-d1-tcon-tv", .data = &sun8i_r40_tv_quirks },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, sun4i_tcon_of_table);
Signature · 1 line
2.35.1
author maintainer
#47 lore raw

PATCH 48/135 scsi: megaraid: Fix error check return value of register_chrdev()

In reply to Sasha Levin

From: Lv Ruyi <[email protected]>

[ Upstream commit c5acd61dbb32b6bda0f3a354108f2b8dcb788985 ]

If major equals 0, register_chrdev() returns an error code when it fails. This function dynamically allocates a major and returns its number on success, so we should use "< 0" to check it instead of "!".

---
 drivers/scsi/megaraid.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/megaraid.c +1 -1
index bf987f3a7f3f..840175f34d1a 100644
@@ -4608,7 +4608,7 @@ static int __init megaraid_init(void)
 	 * major number allocation.
 	 */
 	major = register_chrdev(0, "megadev_legacy", &megadev_fops);
-	if (!major) {
+	if (major < 0) {
 		printk(KERN_WARNING
 				"megaraid: failed to register char device\n");
 	}
Signature · 1 line
2.35.1
author maintainer
#48 lore raw

PATCH 49/135 drm/amdgpu/sdma: Fix incorrect calculations of the wptr of the doorbells

In reply to Sasha Levin

From: Haohui Mai <[email protected]>

[ Upstream commit 7dba6e838e741caadcf27ef717b6dcb561e77f89 ]

This patch fixes the issue where the driver miscomputes the 64-bit values of the wptr of the SDMA doorbell when initializing the hardware. SDMA engines v4 and later on have full 64-bit registers for wptr thus they should be set properly.

Older generation hardwares like CIK / SI have only 16 / 20 / 24bits for the WPTR, where the calls of lower_32_bits() will be removed in a following patch.

---
 drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c | 4 ++--
 drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c | 8 ++++----
 drivers/gpu/drm/amd/amdgpu/sdma_v5_2.c | 8 ++++----
 3 files changed, 10 insertions(+), 10 deletions(-)
drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c +2 -2
index f0638db57111..66b6b175ae90 100644
@@ -772,8 +772,8 @@ static void sdma_v4_0_ring_set_wptr(struct amdgpu_ring *ring)
 
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c +4 -4
index 81e033549dda..6982735e88ba 100644
@@ -400,8 +400,8 @@ static void sdma_v5_0_ring_set_wptr(struct amdgpu_ring *ring)
 	if (ring->use_doorbell) {
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
@@ -780,9 +780,9 @@ static int sdma_v5_0_gfx_resume(struct amdgpu_device *adev)
 
 		if (!amdgpu_sriov_vf(adev)) { /* only bare-metal use register write for wptr */
 			WREG32(sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR),
-			       lower_32_bits(ring->wptr) << 2);
+			       lower_32_bits(ring->wptr << 2));
 			WREG32(sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI),
-			       upper_32_bits(ring->wptr) << 2);
+			       upper_32_bits(ring->wptr << 2));
 		}
 
 		doorbell = RREG32_SOC15_IP(GC, sdma_v5_0_get_reg_offset(adev, i, mmSDMA0_GFX_DOORBELL));
drivers/gpu/drm/amd/amdgpu/sdma_v5_2.c +4 -4
index d3d6d5b045b8..ce3a3d1bdaa8 100644
@@ -287,8 +287,8 @@ static void sdma_v5_2_ring_set_wptr(struct amdgpu_ring *ring)
 	if (ring->use_doorbell) {
 		DRM_DEBUG("Using doorbell -- "
 				"wptr_offs == 0x%08x "
-				"lower_32_bits(ring->wptr) << 2 == 0x%08x "
-				"upper_32_bits(ring->wptr) << 2 == 0x%08x\n",
+				"lower_32_bits(ring->wptr << 2) == 0x%08x "
+				"upper_32_bits(ring->wptr << 2) == 0x%08x\n",
 				ring->wptr_offs,
 				lower_32_bits(ring->wptr << 2),
 				upper_32_bits(ring->wptr << 2));
@@ -664,8 +664,8 @@ static int sdma_v5_2_gfx_resume(struct amdgpu_device *adev)
 		WREG32_SOC15_IP(GC, sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_MINOR_PTR_UPDATE), 1);
 
 		if (!amdgpu_sriov_vf(adev)) { /* only bare-metal use register write for wptr */
-			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR), lower_32_bits(ring->wptr) << 2);
-			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI), upper_32_bits(ring->wptr) << 2);
+			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR), lower_32_bits(ring->wptr << 2));
+			WREG32(sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_RB_WPTR_HI), upper_32_bits(ring->wptr << 2));
 		}
 
 		doorbell = RREG32_SOC15_IP(GC, sdma_v5_2_get_reg_offset(adev, i, mmSDMA0_GFX_DOORBELL));
Signature · 1 line
2.35.1
author maintainer
#49 lore raw

PATCH 50/135 scsi: ufs: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()

In reply to Sasha Levin

From: Minghao Chi <[email protected]>

[ Upstream commit 75b8715e20a20bc7b4844835e4035543a2674200 ]

Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync() and pm_runtime_put_noidle(). This change is just to simplify the code, no actual functional changes.

---
 drivers/scsi/ufs/ti-j721e-ufs.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/scsi/ufs/ti-j721e-ufs.c +2 -4
index eafe0db98d54..122d650d0810 100644
@@ -29,11 +29,9 @@ static int ti_j721e_ufs_probe(struct platform_device *pdev)
 		return PTR_ERR(regbase);
 
 	pm_runtime_enable(dev);
-	ret = pm_runtime_get_sync(dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(dev);
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret < 0)
 		goto disable_pm;
-	}
 
 	/* Select MPHY refclk frequency */
 	clk = devm_clk_get(dev, NULL);
Signature · 1 line
2.35.1
author maintainer
#50 lore raw

PATCH 51/135 scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit 646db1a560f44236b7278b822ca99a1d3b6ea72c ]

If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a received frame, the frame is dropped and resources are leaked.

Fix by returning resources when discarding an unhandled frame type. Update lpfc_fc_frame_check() handling of NOP basic link service.

---
 drivers/scsi/lpfc/lpfc_sli.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/scsi/lpfc/lpfc_sli.c +4 -2
index b64c5f157ce9..f5f472991816 100644
@@ -18466,7 +18466,6 @@ lpfc_fc_frame_check(struct lpfc_hba *phba, struct fc_frame_header *fc_hdr)
 	case FC_RCTL_ELS_REP:	/* extended link services reply */
 	case FC_RCTL_ELS4_REQ:	/* FC-4 ELS request */
 	case FC_RCTL_ELS4_REP:	/* FC-4 ELS reply */
-	case FC_RCTL_BA_NOP:  	/* basic link service NOP */
 	case FC_RCTL_BA_ABTS: 	/* basic link service abort */
 	case FC_RCTL_BA_RMC: 	/* remove connection */
 	case FC_RCTL_BA_ACC:	/* basic accept */
@@ -18487,6 +18486,7 @@ lpfc_fc_frame_check(struct lpfc_hba *phba, struct fc_frame_header *fc_hdr)
 		fc_vft_hdr = (struct fc_vft_header *)fc_hdr;
 		fc_hdr = &((struct fc_frame_header *)fc_vft_hdr)[1];
 		return lpfc_fc_frame_check(phba, fc_hdr);
+	case FC_RCTL_BA_NOP:	/* basic link service NOP */
 	default:
 		goto drop;
 	}
@@ -19299,12 +19299,14 @@ lpfc_sli4_send_seq_to_ulp(struct lpfc_vport *vport,
 	if (!lpfc_complete_unsol_iocb(phba,
 				      phba->sli4_hba.els_wq->pring,
 				      iocbq, fc_hdr->fh_r_ctl,
-				      fc_hdr->fh_type))
+				      fc_hdr->fh_type)) {
 		lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
 				"2540 Ring %d handler: unexpected Rctl "
 				"x%x Type x%x received\n",
 				LPFC_ELS_RING,
 				fc_hdr->fh_r_ctl, fc_hdr->fh_type);
+		lpfc_in_buf_free(phba, &seq_dmabuf->dbuf);
+	}
 
 	/* Free iocb created in lpfc_prep_seq */
 	list_for_each_entry_safe(curr_iocb, next_iocb,
Signature · 1 line
2.35.1
author maintainer
#51 lore raw

PATCH 52/135 ath11k: disable spectral scan during spectral deinit

In reply to Sasha Levin

From: Hari Chandrakanthan <[email protected]>

[ Upstream commit 161c64de239c7018e0295e7e0520a19f00aa32dc ]

When ath11k modules are removed using rmmod with spectral scan enabled, crash is observed. Different crash trace is observed for each crash.

Send spectral scan disable WMI command to firmware before cleaning the spectral dbring in the spectral_deinit API to avoid this crash.

call trace from one of the crash observed:

[ 1252.880802] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 1252.882722] pgd = 0f42e886
[ 1252.890955] [00000008] *pgd=00000000
[ 1252.893478] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1253.093035] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.89 #0
[ 1253.115261] Hardware name: Generic DT based system
[ 1253.121149] PC is at ath11k_spectral_process_data+0x434/0x574 [ath11k]
[ 1253.125940] LR is at 0x88e31017
[ 1253.132448] pc : [<7f9387b8>]    lr : [<88e31017>]    psr: a0000193
[ 1253.135488] sp : 80d01bc8  ip : 00000001  fp : 970e0000
[ 1253.141737] r10: 88e31000  r9 : 970ec000  r8 : 00000080
[ 1253.146946] r7 : 94734040  r6 : a0000113  r5 : 00000057  r4 : 00000000
[ 1253.152159] r3 : e18cb694  r2 : 00000217  r1 : 1df1f000  r0 : 00000001
[ 1253.158755] Flags: NzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[ 1253.165266] Control: 10c0383d  Table: 5e71006a  DAC: 00000055
[ 1253.172472] Process swapper/0 (pid: 0, stack limit = 0x60870141)
[ 1253.458055] [<7f9387b8>] (ath11k_spectral_process_data [ath11k]) from [<7f917fdc>] (ath11k_dbring_buffer_release_event+0x214/0x2e4 [ath11k])
[ 1253.466139] [<7f917fdc>] (ath11k_dbring_buffer_release_event [ath11k]) from [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx+0x1840/0x29cc [ath11k])
[ 1253.478807] [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx [ath11k]) from [<7f8fe868>] (ath11k_htc_rx_completion_handler+0x180/0x4e0 [ath11k])
[ 1253.490699] [<7f8fe868>] (ath11k_htc_rx_completion_handler [ath11k]) from [<7f91308c>] (ath11k_ce_per_engine_service+0x2c4/0x3b4 [ath11k])
[ 1253.502386] [<7f91308c>] (ath11k_ce_per_engine_service [ath11k]) from [<7f9a4198>] (ath11k_pci_ce_tasklet+0x28/0x80 [ath11k_pci])
[ 1253.514811] [<7f9a4198>] (ath11k_pci_ce_tasklet [ath11k_pci]) from [<8032227c>] (tasklet_action_common.constprop.2+0x64/0xe8)
[ 1253.526476] [<8032227c>] (tasklet_action_common.constprop.2) from [<803021e8>] (__do_softirq+0x130/0x2d0)
[ 1253.537756] [<803021e8>] (__do_softirq) from [<80322610>] (irq_exit+0xcc/0xe8)
[ 1253.547304] [<80322610>] (irq_exit) from [<8036a4a4>] (__handle_domain_irq+0x60/0xb4)
[ 1253.554428] [<8036a4a4>] (__handle_domain_irq) from [<805eb348>] (gic_handle_irq+0x4c/0x90)
[ 1253.562321] [<805eb348>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)

Tested-on: QCN6122 hw1.0 AHB WLAN.HK.2.6.0.1-00851-QCAHKSWPL_SILICONZ-1

---
 drivers/net/wireless/ath/ath11k/spectral.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)
drivers/net/wireless/ath/ath11k/spectral.c +9 -8
index 4100cc1449a2..e997426a1b4b 100644
@@ -212,7 +212,10 @@ static int ath11k_spectral_scan_config(struct ath11k *ar,
 		return -ENODEV;
 
 	arvif->spectral_enabled = (mode != ATH11K_SPECTRAL_DISABLED);
+
+	spin_lock_bh(&ar->spectral.lock);
 	ar->spectral.mode = mode;
+	spin_unlock_bh(&ar->spectral.lock);
 
 	ret = ath11k_wmi_vdev_spectral_enable(ar, arvif->vdev_id,
 					      ATH11K_WMI_SPECTRAL_TRIGGER_CMD_CLEAR,
@@ -843,9 +846,6 @@ static inline void ath11k_spectral_ring_free(struct ath11k *ar)
 {
 	struct ath11k_spectral *sp = &ar->spectral;
 
-	if (!sp->enabled)
-		return;
-
 	ath11k_dbring_srng_cleanup(ar, &sp->rx_ring);
 	ath11k_dbring_buf_cleanup(ar, &sp->rx_ring);
 }
@@ -897,15 +897,16 @@ void ath11k_spectral_deinit(struct ath11k_base *ab)
 		if (!sp->enabled)
 			continue;
 
-		ath11k_spectral_debug_unregister(ar);
-		ath11k_spectral_ring_free(ar);
+		mutex_lock(&ar->conf_mutex);
+		ath11k_spectral_scan_config(ar, ATH11K_SPECTRAL_DISABLED);
+		mutex_unlock(&ar->conf_mutex);
 
 		spin_lock_bh(&sp->lock);
-
-		sp->mode = ATH11K_SPECTRAL_DISABLED;
 		sp->enabled = false;
-
 		spin_unlock_bh(&sp->lock);
+
+		ath11k_spectral_debug_unregister(ar);
+		ath11k_spectral_ring_free(ar);
 	}
 }
 
Signature · 7 lines
2.35.1


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
author maintainer
#52 lore raw

PATCH 53/135 ASoC: Intel: bytcr_rt5640: Add quirk for the HP Pro Tablet 408

In reply to Sasha Levin

From: Hans de Goede <[email protected]>

[ Upstream commit ce216cfa84a4e1c23b105e652c550bdeaac9e922 ]

Add a quirk for the HP Pro Tablet 408, this BYTCR tablet has no CHAN package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which is the default for BYTCR devices.

It also uses DMIC1 for the internal mic rather then the default IN3 and it uses JD2 rather then the default JD1 for jack-detect.

---
 sound/soc/intel/boards/bytcr_rt5640.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
sound/soc/intel/boards/bytcr_rt5640.c +12 -0
index 2ace32c03ec9..b5ac226c59e1 100644
@@ -773,6 +773,18 @@ static const struct dmi_system_id byt_rt5640_quirk_table[] = {
 					BYT_RT5640_OVCD_SF_0P75 |
 					BYT_RT5640_MCLK_EN),
 	},
+	{	/* HP Pro Tablet 408 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pro Tablet 408"),
+		},
+		.driver_data = (void *)(BYT_RT5640_DMIC1_MAP |
+					BYT_RT5640_JD_SRC_JD2_IN4N |
+					BYT_RT5640_OVCD_TH_1500UA |
+					BYT_RT5640_OVCD_SF_0P75 |
+					BYT_RT5640_SSP0_AIF1 |
+					BYT_RT5640_MCLK_EN),
+	},
 	{	/* HP Stream 7 */
 		.matches = {
 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
Signature · 1 line
2.35.1
author maintainer
#53 lore raw

PATCH 54/135 drm/plane: Move range check for format_count earlier

In reply to Sasha Levin

From: Steven Price <[email protected]>

[ Upstream commit 4b674dd69701c2e22e8e7770c1706a69f3b17269 ]

While the check for format_count > 64 in __drm_universal_plane_init() shouldn't be hit (it's a WARN_ON), in its current position it will then leak the plane->format_types array and fail to call drm_mode_object_unregister() leaking the modeset identifier. Move it to the start of the function to avoid allocating those resources in the first place.

---
 drivers/gpu/drm/drm_plane.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/gpu/drm/drm_plane.c +7 -7
index 82afb854141b..fd0bf90fb4c2 100644
@@ -249,6 +249,13 @@ static int __drm_universal_plane_init(struct drm_device *dev,
 	if (WARN_ON(config->num_total_plane >= 32))
 		return -EINVAL;
 
+	/*
+	 * First driver to need more than 64 formats needs to fix this. Each
+	 * format is encoded as a bit and the current code only supports a u64.
+	 */
+	if (WARN_ON(format_count > 64))
+		return -EINVAL;
+
 	WARN_ON(drm_drv_uses_atomic_modeset(dev) &&
 		(!funcs->atomic_destroy_state ||
 		 !funcs->atomic_duplicate_state));
@@ -270,13 +277,6 @@ static int __drm_universal_plane_init(struct drm_device *dev,
 		return -ENOMEM;
 	}
 
-	/*
-	 * First driver to need more than 64 formats needs to fix this. Each
-	 * format is encoded as a bit and the current code only supports a u64.
-	 */
-	if (WARN_ON(format_count > 64))
-		return -EINVAL;
-
 	if (format_modifiers) {
 		const uint64_t *temp_modifiers = format_modifiers;
 
Signature · 1 line
2.35.1
author maintainer
#54 lore raw

PATCH 55/135 drm/amd/pm: fix the compile warning

In reply to Sasha Levin

From: Evan Quan <[email protected]>

[ Upstream commit 555238d92ac32dbad2d77ad2bafc48d17391990c ]

Fix the compile warning below:
drivers/gpu/drm/amd/amdgpu/../pm/legacy-dpm/kv_dpm.c:1641
kv_get_acp_boot_level() warn: always true condition '(table->entries[i]->clk >= 0) => (0-u32max >= 0)'

---
 drivers/gpu/drm/amd/pm/powerplay/kv_dpm.c | 14 +-------------
 1 file changed, 1 insertion(+), 13 deletions(-)
drivers/gpu/drm/amd/pm/powerplay/kv_dpm.c +1 -13
index bcae42cef374..6ba4c2ae69a6 100644
@@ -1609,19 +1609,7 @@ static int kv_update_samu_dpm(struct amdgpu_device *adev, bool gate)
 
 static u8 kv_get_acp_boot_level(struct amdgpu_device *adev)
 {
-	u8 i;
-	struct amdgpu_clock_voltage_dependency_table *table =
-		&adev->pm.dpm.dyn_state.acp_clock_voltage_dependency_table;
-
-	for (i = 0; i < table->count; i++) {
-		if (table->entries[i].clk >= 0) /* XXX */
-			break;
-	}
-
-	if (i >= table->count)
-		i = table->count - 1;
-
-	return i;
+	return 0;
 }
 
 static void kv_update_acp_boot_level(struct amdgpu_device *adev)
Signature · 1 line
2.35.1
author maintainer
#55 lore raw

PATCH 56/135 ath10k: skip ath10k_halt during suspend for driver state RESTARTING

In reply to Sasha Levin

From: Abhishek Kumar <[email protected]>

[ Upstream commit b72a4aff947ba807177bdabb43debaf2c66bee05 ]

Double free crash is observed when FW recovery(caused by wmi timeout/crash) is followed by immediate suspend event. The FW recovery is triggered by ath10k_core_restart() which calls driver clean up via ath10k_halt(). When the suspend event occurs between the FW recovery, the restart worker thread is put into frozen state until suspend completes. The suspend event triggers ath10k_stop() which again triggers ath10k_halt() The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be called twice(Note: ath10k_htt_rx_alloc was not called by restart worker thread because of its frozen state), causing the crash.

To fix this, during the suspend flow, skip call to ath10k_halt() in ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING. Also, for driver state ATH10K_STATE_RESTARTING, call ath10k_wait_for_suspend() in ath10k_stop(). This is because call to ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state ATH10K_STATE_RESTARTING.

The frozen restart worker thread will be cancelled during resume when the device comes out of suspend.

Below is the crash stack for reference:

[  428.469167] ------------[ cut here ]------------
[  428.469180] kernel BUG at mm/slub.c:4150!
[  428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[  428.469219] Workqueue: events_unbound async_run_entry_fn
[  428.469230] RIP: 0010:kfree+0x319/0x31b
[  428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246
[  428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000
[  428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000
[  428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000
[  428.469276] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  428.469285] Call Trace:
[  428.469295]  ? dma_free_attrs+0x5f/0x7d
[  428.469320]  ath10k_core_stop+0x5b/0x6f
[  428.469336]  ath10k_halt+0x126/0x177
[  428.469352]  ath10k_stop+0x41/0x7e
[  428.469387]  drv_stop+0x88/0x10e
[  428.469410]  __ieee80211_suspend+0x297/0x411
[  428.469441]  rdev_suspend+0x6e/0xd0
[  428.469462]  wiphy_suspend+0xb1/0x105
[  428.469483]  ? name_show+0x2d/0x2d
[  428.469490]  dpm_run_callback+0x8c/0x126
[  428.469511]  ? name_show+0x2d/0x2d
[  428.469517]  __device_suspend+0x2e7/0x41b
[  428.469523]  async_suspend+0x1f/0x93
[  428.469529]  async_run_entry_fn+0x3d/0xd1
[  428.469535]  process_one_work+0x1b1/0x329
[  428.469541]  worker_thread+0x213/0x372
[  428.469547]  kthread+0x150/0x15f
[  428.469552]  ? pr_cont_work+0x58/0x58
[  428.469558]  ? kthread_blkcg+0x31/0x31

Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1

---
 drivers/net/wireless/ath/ath10k/mac.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)
drivers/net/wireless/ath/ath10k/mac.c +18 -2
index b11aaee8b8c0..a11b31191d5a 100644
@@ -5339,13 +5339,29 @@ static int ath10k_start(struct ieee80211_hw *hw)
 static void ath10k_stop(struct ieee80211_hw *hw)
 {
 	struct ath10k *ar = hw->priv;
+	u32 opt;
 
 	ath10k_drain_tx(ar);
 
 	mutex_lock(&ar->conf_mutex);
 	if (ar->state != ATH10K_STATE_OFF) {
-		if (!ar->hw_rfkill_on)
-			ath10k_halt(ar);
+		if (!ar->hw_rfkill_on) {
+			/* If the current driver state is RESTARTING but not yet
+			 * fully RESTARTED because of incoming suspend event,
+			 * then ath10k_halt() is already called via
+			 * ath10k_core_restart() and should not be called here.
+			 */
+			if (ar->state != ATH10K_STATE_RESTARTING) {
+				ath10k_halt(ar);
+			} else {
+				/* Suspending here, because when in RESTARTING
+				 * state, ath10k_core_stop() skips
+				 * ath10k_wait_for_suspend().
+				 */
+				opt = WMI_PDEV_SUSPEND_AND_DISABLE_INTR;
+				ath10k_wait_for_suspend(ar, opt);
+			}
+		}
 		ar->state = ATH10K_STATE_OFF;
 	}
 	mutex_unlock(&ar->conf_mutex);
Signature · 7 lines
2.35.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#56 lore raw

PATCH 57/135 arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall

In reply to Sasha Levin

From: Alexandru Elisei <[email protected]>

[ Upstream commit 3fed9e551417b84038b15117732ea4505eee386b ]

If a compat process tries to execute an unknown system call above the __ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the offending process. Information about the error is printed to dmesg in compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() -> arm64_show_signal().

arm64_show_signal() interprets a non-zero value for current->thread.fault_code as an exception syndrome and displays the message associated with the ESR_ELx.EC field (bits 31:26). current->thread.fault_code is set in compat_arm_syscall() -> arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx value. This means that the ESR_ELx.EC field has the value that the user set for the syscall number and the kernel can end up printing bogus exception messages*. For example, for the syscall number 0x68000000, which evaluates to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error:

[   18.349161] syscall[300]: unhandled exception: ERET/ERETAA/ERETAB, ESR 0x68000000, Oops - bad compat syscall(2) in syscall[10000+50000]
[   18.350639] CPU: 2 PID: 300 Comm: syscall Not tainted 5.18.0-rc1 #79
[   18.351249] Hardware name: Pine64 RockPro64 v2.0 (DT)

[..]

which is misleading, as the bad compat syscall has nothing to do with pointer authentication.

Stop arm64_show_signal() from printing exception syndrome information by having compat_arm_syscall() set the ESR_ELx value to 0, as it has no meaning for an invalid system call number. The example above now becomes:

[   19.935275] syscall[301]: unhandled exception: Oops - bad compat syscall(2) in syscall[10000+50000]
[   19.936124] CPU: 1 PID: 301 Comm: syscall Not tainted 5.18.0-rc1-00005-g7e08006d4102 #80
[   19.936894] Hardware name: Pine64 RockPro64 v2.0 (DT)

[..]

which although shows less information because the syscall number, wrongfully advertised as the ESR value, is missing, it is better than showing plainly wrong information. The syscall number can be easily obtained with strace.

*A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END evaluates to true; the syscall will exit to userspace in this case with the ENOSYS error code instead of arm64_notify_die() being called.

---
 arch/arm64/kernel/sys_compat.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/kernel/sys_compat.c +1 -1
index db5159a3055f..b88a52f7188f 100644
@@ -114,6 +114,6 @@ long compat_arm_syscall(struct pt_regs *regs, int scno)
 	addr = instruction_pointer(regs) - (compat_thumb_mode(regs) ? 2 : 4);
 
 	arm64_notify_die("Oops - bad compat syscall(2)", regs,
-			 SIGILL, ILL_ILLTRP, addr, scno);
+			 SIGILL, ILL_ILLTRP, addr, 0);
 	return 0;
 }
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#57 lore raw

PATCH 58/135 drm: msm: fix error check return value of irq_of_parse_and_map()

In reply to Sasha Levin

From: Lv Ruyi <[email protected]>

[ Upstream commit b9e4f1d2b505df8e2439b63e67afaa287c1c43e2 ]

The irq_of_parse_and_map() function returns 0 on failure, and does not return an negative value.

Patchwork: https://patchwork.freedesktop.org/patch/483175/

---
 drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c +3 -3
index 12a5f81e402b..1c0dde825e57 100644
@@ -577,9 +577,9 @@ struct msm_kms *mdp5_kms_init(struct drm_device *dev)
 	}
 
 	irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
-	if (irq < 0) {
-		ret = irq;
-		DRM_DEV_ERROR(&pdev->dev, "failed to get irq: %d\n", ret);
+	if (!irq) {
+		ret = -EINVAL;
+		DRM_DEV_ERROR(&pdev->dev, "failed to get irq\n");
 		goto fail;
 	}
 
Signature · 1 line
2.35.1
author maintainer
#58 lore raw

PATCH 59/135 drm/msm/dpu: Clean up CRC debug logs

In reply to Sasha Levin

From: Jessica Zhang <[email protected]>

[ Upstream commit 3ce8bdca394fc606b55e7c5ed779d171aaae5d09 ]

Currently, dpu_hw_lm_collect_misr returns EINVAL if CRC is disabled. This causes a lot of spam in the DRM debug logs as it's called for every vblank.

Instead of returning EINVAL when CRC is disabled in dpu_hw_lm_collect_misr, let's return ENODATA and add an extra ENODATA check before the debug log in dpu_crtc_get_crc.

Changes since V1:
- Added reported-by and suggested-by tags

Patchwork: https://patchwork.freedesktop.org/patch/484274/

---
 drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c  | 3 ++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c | 2 +-
 2 files changed, 3 insertions(+), 2 deletions(-)
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c +2 -1
index e7c9fe1a250f..0a857f222982 100644
@@ -204,7 +204,8 @@ static int dpu_crtc_get_crc(struct drm_crtc *crtc)
 		rc = m->hw_lm->ops.collect_misr(m->hw_lm, &crcs[i]);
 
 		if (rc) {
-			DRM_DEBUG_DRIVER("MISR read failed\n");
+			if (rc != -ENODATA)
+				DRM_DEBUG_DRIVER("MISR read failed\n");
 			return rc;
 		}
 	}
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c +1 -1
index 86363c0ec834..462f5082099e 100644
@@ -138,7 +138,7 @@ static int dpu_hw_lm_collect_misr(struct dpu_hw_mixer *ctx, u32 *misr_value)
 	ctrl = DPU_REG_READ(c, LM_MISR_CTRL);
 
 	if (!(ctrl & LM_MISR_CTRL_ENABLE))
-		return -EINVAL;
+		return -ENODATA;
 
 	if (!(ctrl & LM_MISR_CTRL_STATUS))
 		return -EINVAL;
Signature · 1 line
2.35.1
author maintainer
#59 lore raw

PATCH 60/135 xtensa: move trace_hardirqs_off call back to entry.S

In reply to Sasha Levin

From: Max Filippov <[email protected]>

[ Upstream commit de4415d0bac91192ee9c74e849bc61429efa9b42 ]

Context tracking call must be done after hardirq tracking call, otherwise lockdep_assert_irqs_disabled called from rcu_eqs_exit gives a warning. To avoid context tracking logic duplication for IRQ/exception entry paths move trace_hardirqs_off call back to common entry code.

---
 arch/xtensa/kernel/entry.S | 19 +++++++++++++------
 arch/xtensa/kernel/traps.c | 11 ++---------
 2 files changed, 15 insertions(+), 15 deletions(-)
arch/xtensa/kernel/entry.S +13 -6
index a1029a5b6a1d..ee08238099f4 100644
@@ -442,7 +442,6 @@ KABI_W	or	a3, a3, a0
 	moveqz	a3, a0, a2		# a3 = LOCKLEVEL iff interrupt
 KABI_W	movi	a2, PS_WOE_MASK
 KABI_W	or	a3, a3, a2
-	rsr	a2, exccause
 #endif
 
 	/* restore return address (or 0 if return to userspace) */
@@ -469,19 +468,27 @@ KABI_W	or	a3, a3, a2
 
 	save_xtregs_opt a1 a3 a4 a5 a6 a7 PT_XTREGS_OPT
 	
+#ifdef CONFIG_TRACE_IRQFLAGS
+	rsr		abi_tmp0, ps
+	extui		abi_tmp0, abi_tmp0, PS_INTLEVEL_SHIFT, PS_INTLEVEL_WIDTH
+	beqz		abi_tmp0, 1f
+	abi_call	trace_hardirqs_off
+1:
+#endif
+
 	/* Go to second-level dispatcher. Set up parameters to pass to the
 	 * exception handler and call the exception handler.
 	 */
 
-	rsr	a4, excsave1
-	addx4	a4, a2, a4
-	l32i	a4, a4, EXC_TABLE_DEFAULT		# load handler
-	mov	abi_arg1, a2			# pass EXCCAUSE
+	l32i	abi_arg1, a1, PT_EXCCAUSE	# pass EXCCAUSE
+	rsr	abi_tmp0, excsave1
+	addx4	abi_tmp0, abi_arg1, abi_tmp0
+	l32i	abi_tmp0, abi_tmp0, EXC_TABLE_DEFAULT	# load handler
 	mov	abi_arg0, a1			# pass stack frame
 
 	/* Call the second-level handler */
 
-	abi_callx	a4
+	abi_callx	abi_tmp0
 
 	/* Jump here for exception exit */
 	.global common_exception_return
arch/xtensa/kernel/traps.c +2 -9
index 9345007d474d..5f86208c67c8 100644
@@ -242,12 +242,8 @@ DEFINE_PER_CPU(unsigned long, nmi_count);
 
 void do_nmi(struct pt_regs *regs)
 {
-	struct pt_regs *old_regs;
+	struct pt_regs *old_regs = set_irq_regs(regs);
 
-	if ((regs->ps & PS_INTLEVEL_MASK) < LOCKLEVEL)
-		trace_hardirqs_off();
-
-	old_regs = set_irq_regs(regs);
 	nmi_enter();
 	++*this_cpu_ptr(&nmi_count);
 	check_valid_nmi();
@@ -269,12 +265,9 @@ void do_interrupt(struct pt_regs *regs)
 		XCHAL_INTLEVEL6_MASK,
 		XCHAL_INTLEVEL7_MASK,
 	};
-	struct pt_regs *old_regs;
+	struct pt_regs *old_regs = set_irq_regs(regs);
 	unsigned unhandled = ~0u;
 
-	trace_hardirqs_off();
-
-	old_regs = set_irq_regs(regs);
 	irq_enter();
 
 	for (;;) {
Signature · 1 line
2.35.1
author maintainer
#60 lore raw

PATCH 61/135 ath11k: fix warning of not found station for bssid in message

In reply to Sasha Levin

From: Wen Gong <[email protected]>

[ Upstream commit 7330e1ec9748948177830c6e1a13379835d577f9 ]

When test connect/disconnect to an AP frequently with WCN6855, sometimes it show below log.

[  277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[  277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[  277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif         pK-error
[  277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[  277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[  277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[  277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[  277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif         pK-error
[  277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[  277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[  277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[  278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110

Reason is:
When running disconnect operation, sta_info removed from local->sta_hash by __sta_info_destroy_part1() from __sta_info_flush(), after this, ieee80211_find_sta_by_ifaddr() which called by ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse() cannot find this station, then failed log printed.

steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1() and __sta_info_destroy_part2().

2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)" and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the list of ieee80211_hw.

3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(), then peer->sta is clear at this moment.

4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics() ->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.

5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the ieee80211_sta can not be found again because it has remove from list in step2 and also peer->sta is clear in step3.

6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()-> sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed in memory, then the failed log will not happen because function ath11k_mac_op_sta_state() will not be called.

Actually this print log is not a real error, it is only to skip parse the info, so change to skip print by default debug setting.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

---
 drivers/net/wireless/ath/ath11k/wmi.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
drivers/net/wireless/ath/ath11k/wmi.c +6 -5
index 22921673e956..4ad3fe7d7d1f 100644
@@ -5616,9 +5616,9 @@ static int ath11k_wmi_tlv_rssi_chain_parse(struct ath11k_base *ab,
 					   arvif->bssid,
 					   NULL);
 	if (!sta) {
-		ath11k_warn(ab, "not found station for bssid %pM\n",
-			    arvif->bssid);
-		ret = -EPROTO;
+		ath11k_dbg(ab, ATH11K_DBG_WMI,
+			   "not found station of bssid %pM for rssi chain\n",
+			   arvif->bssid);
 		goto exit;
 	}
 
@@ -5716,8 +5716,9 @@ static int ath11k_wmi_tlv_fw_stats_data_parse(struct ath11k_base *ab,
 					   "wmi stats vdev id %d snr %d\n",
 					   src->vdev_id, src->beacon_snr);
 			} else {
-				ath11k_warn(ab, "not found station for bssid %pM\n",
-					    arvif->bssid);
+				ath11k_dbg(ab, ATH11K_DBG_WMI,
+					   "not found station of bssid %pM for vdev stat\n",
+					   arvif->bssid);
 			}
 		}
 
Signature · 7 lines
2.35.1


-- 
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
author maintainer
#61 lore raw

PATCH 62/135 scsi: target: tcmu: Fix possible data corruption

In reply to Sasha Levin

From: Xiaoguang Wang <[email protected]>

[ Upstream commit bb9b9eb0ae2e9d3f6036f0ad907c3a83dcd43485 ]

When tcmu_vma_fault() gets a page successfully, before the current context completes page fault procedure, find_free_blocks() may run and call unmap_mapping_range() to unmap the page. Assume that when find_free_blocks() initially completes and the previous page fault procedure starts to run again and completes, then one truncated page has been mapped to userspace. But note that tcmu_vma_fault() has gotten a refcount for the page so any other subsystem won't be able to use the page unless the userspace address is unmapped later.

If another command subsequently runs and needs to extend dbi_thresh it may reuse the corresponding slot for the previous page in data_bitmap. Then though we'll allocate new page for this slot in data_area, no page fault will happen because we have a valid map and the real request's data will be lost.

Filesystem implementations will also run into this issue but they usually lock the page when vm_operations_struct->fault gets a page and unlock the page after finish_fault() completes. For truncate filesystems lock pages in truncate_inode_pages() to protect against racing wrt. page faults.

To fix this possible data corruption scenario we can apply a method similar to the filesystems. For pages that are to be freed, tcmu_blocks_release() locks and unlocks. Make tcmu_vma_fault() also lock found page under cmdr_lock. At the same time, since tcmu_vma_fault() gets an extra page refcount, tcmu_blocks_release() won't free pages if pages are in page fault procedure, which means it is safe to call tcmu_blocks_release() before unmap_mapping_range().

With these changes tcmu_blocks_release() will wait for all page faults to be completed before calling unmap_mapping_range(). And later, if unmap_mapping_range() is called, it will ensure stale mappings are removed.

---
 drivers/target/target_core_user.c | 40 ++++++++++++++++++++++++++++---
 1 file changed, 37 insertions(+), 3 deletions(-)
drivers/target/target_core_user.c +37 -3
index 06a5c4086551..f26767a55d38 100644
@@ -20,6 +20,7 @@
 #include <linux/configfs.h>
 #include <linux/mutex.h>
 #include <linux/workqueue.h>
+#include <linux/pagemap.h>
 #include <net/genetlink.h>
 #include <scsi/scsi_common.h>
 #include <scsi/scsi_proto.h>
@@ -1666,6 +1667,26 @@ static u32 tcmu_blocks_release(struct tcmu_dev *udev, unsigned long first,
 	xas_lock(&xas);
 	xas_for_each(&xas, page, (last + 1) * udev->data_pages_per_blk - 1) {
 		xas_store(&xas, NULL);
+		/*
+		 * While reaching here there may be page faults occurring on
+		 * the to-be-released pages. A race condition may occur if
+		 * unmap_mapping_range() is called before page faults on these
+		 * pages have completed; a valid but stale map is created.
+		 *
+		 * If another command subsequently runs and needs to extend
+		 * dbi_thresh, it may reuse the slot corresponding to the
+		 * previous page in data_bitmap. Though we will allocate a new
+		 * page for the slot in data_area, no page fault will happen
+		 * because we have a valid map. Therefore the command's data
+		 * will be lost.
+		 *
+		 * We lock and unlock pages that are to be released to ensure
+		 * all page faults have completed. This way
+		 * unmap_mapping_range() can ensure stale maps are cleanly
+		 * removed.
+		 */
+		lock_page(page);
+		unlock_page(page);
 		__free_page(page);
 		pages_freed++;
 	}
@@ -1821,6 +1842,7 @@ static struct page *tcmu_try_get_data_page(struct tcmu_dev *udev, uint32_t dpi)
 	page = xa_load(&udev->data_pages, dpi);
 	if (likely(page)) {
 		get_page(page);
+		lock_page(page);
 		mutex_unlock(&udev->cmdr_lock);
 		return page;
 	}
@@ -1862,6 +1884,7 @@ static vm_fault_t tcmu_vma_fault(struct vm_fault *vmf)
 	struct page *page;
 	unsigned long offset;
 	void *addr;
+	vm_fault_t ret = 0;
 
 	int mi = tcmu_find_mem_index(vmf->vma);
 	if (mi < 0)
@@ -1886,10 +1909,11 @@ static vm_fault_t tcmu_vma_fault(struct vm_fault *vmf)
 		page = tcmu_try_get_data_page(udev, dpi);
 		if (!page)
 			return VM_FAULT_SIGBUS;
+		ret = VM_FAULT_LOCKED;
 	}
 
 	vmf->page = page;
-	return 0;
+	return ret;
 }
 
 static const struct vm_operations_struct tcmu_vm_ops = {
@@ -3152,12 +3176,22 @@ static void find_free_blocks(void)
 			udev->dbi_max = block;
 		}
 
+		/*
+		 * Release the block pages.
+		 *
+		 * Also note that since tcmu_vma_fault() gets an extra page
+		 * refcount, tcmu_blocks_release() won't free pages if pages
+		 * are mapped. This means it is safe to call
+		 * tcmu_blocks_release() before unmap_mapping_range() which
+		 * drops the refcount of any pages it unmaps and thus releases
+		 * them.
+		 */
+		pages_freed = tcmu_blocks_release(udev, start, end - 1);
+
 		/* Here will truncate the data area from off */
 		off = udev->data_off + (loff_t)start * udev->data_blk_size;
 		unmap_mapping_range(udev->inode->i_mapping, off, 0, 1);
 
-		/* Release the block pages */
-		pages_freed = tcmu_blocks_release(udev, start, end - 1);
 		mutex_unlock(&udev->cmdr_lock);
 
 		total_pages_freed += pages_freed;
Signature · 1 line
2.35.1
author maintainer
#62 lore raw

PATCH 63/135 ipv6: Don't send rs packets to the interface of ARPHRD_TUNNEL

In reply to Sasha Levin

From: jianghaoran <[email protected]>

[ Upstream commit b52e1cce31ca721e937d517411179f9196ee6135 ]

ARPHRD_TUNNEL interface can't process rs packets
and will generate TX errors

ex:
ip tunnel add ethn mode ipip local 192.168.1.1 remote 192.168.1.2 ifconfig ethn x.x.x.x

ethn: flags=209<UP,POINTOPOINT,RUNNING,NOARP> mtu 1480
inet x.x.x.x netmask 255.255.255.255 destination x.x.x.x inet6 fe80::5efe:ac1e:3cdb prefixlen 64 scopeid 0x20<link>
tunnel txqueuelen 1000 (IPIP Tunnel)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 3 dropped 0 overruns 0 carrier 0 collisions 0

---
 net/ipv6/addrconf.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
net/ipv6/addrconf.c +2 -1
index 0a9e03465001..5ec289e0f2ac 100644
@@ -4221,7 +4221,8 @@ static void addrconf_dad_completed(struct inet6_ifaddr *ifp, bool bump_id,
 	send_rs = send_mld &&
 		  ipv6_accept_ra(ifp->idev) &&
 		  ifp->idev->cnf.rtr_solicits != 0 &&
-		  (dev->flags&IFF_LOOPBACK) == 0;
+		  (dev->flags & IFF_LOOPBACK) == 0 &&
+		  (dev->type != ARPHRD_TUNNEL);
 	read_unlock_bh(&ifp->idev->lock);
 
 	/* While dad is in progress mld report's source address is in6_addrany.
Signature · 1 line
2.35.1
author maintainer
#63 lore raw

PATCH 64/135 net/mlx5: fs, delete the FTE when there are no rules attached to it

In reply to Sasha Levin

From: Mark Bloch <[email protected]>

[ Upstream commit 7b0c6338597613f465d131bd939a51844a00455a ]

When an FTE has no children is means all the rules where removed and the FTE can be deleted regardless of the dests_size value. While dests_size should be 0 when there are no children be extra careful not to leak memory or get firmware syndrome if the proper bookkeeping of dests_size wasn't done.

---
 drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/fs_core.c +5 -5
index b6f58d16d145..298c614c631b 100644
@@ -2064,16 +2064,16 @@ void mlx5_del_flow_rules(struct mlx5_flow_handle *handle)
 	down_write_ref_node(&fte->node, false);
 	for (i = handle->num_rules - 1; i >= 0; i--)
 		tree_remove_node(&handle->rule[i]->node, true);
-	if (fte->dests_size) {
-		if (fte->modify_mask)
-			modify_fte(fte);
-		up_write_ref_node(&fte->node, false);
-	} else if (list_empty(&fte->node.children)) {
+	if (list_empty(&fte->node.children)) {
 		del_hw_fte(&fte->node);
 		/* Avoid double call to del_hw_fte */
 		fte->node.del_hw_func = NULL;
 		up_write_ref_node(&fte->node, false);
 		tree_put_node(&fte->node, false);
+	} else if (fte->dests_size) {
+		if (fte->modify_mask)
+			modify_fte(fte);
+		up_write_ref_node(&fte->node, false);
 	} else {
 		up_write_ref_node(&fte->node, false);
 	}
Signature · 1 line
2.35.1
author maintainer
#64 lore raw

PATCH 65/135 ASoC: dapm: Don't fold register value changes into notifications

In reply to Sasha Levin

From: Mark Brown <[email protected]>

[ Upstream commit ad685980469b9f9b99d4d6ea05f4cb8f57cb2234 ]

DAPM tracks and reports the value presented to the user from DAPM controls separately to the register value, these may diverge during initialisation or when an autodisable control is in use.

When writing DAPM controls we currently report that a change has occurred if either the DAPM value or the value stored in the register has changed, meaning that if the two are out of sync we may appear to report a spurious event to userspace. Since we use this folded in value for nothing other than the value reported to userspace simply drop the folding in of the register change.

---
 sound/soc/soc-dapm.c | 2 --
 1 file changed, 2 deletions(-)
sound/soc/soc-dapm.c +0 -2
index fb43b331a36e..f62dd119639d 100644
@@ -3430,7 +3430,6 @@ int snd_soc_dapm_put_volsw(struct snd_kcontrol *kcontrol,
 			update.val = val;
 			card->update = &update;
 		}
-		change |= reg_change;
 
 		ret = soc_dapm_mixer_update_power(card, kcontrol, connect,
 						  rconnect);
@@ -3532,7 +3531,6 @@ int snd_soc_dapm_put_enum_double(struct snd_kcontrol *kcontrol,
 			update.val = val;
 			card->update = &update;
 		}
-		change |= reg_change;
 
 		ret = soc_dapm_mux_update_power(card, kcontrol, item[0], e);
 
Signature · 1 line
2.35.1
author maintainer
#65 lore raw

PATCH 66/135 mlxsw: spectrum_dcb: Do not warn about priority changes

In reply to Sasha Levin

From: Petr Machata <[email protected]>

[ Upstream commit b6b584562cbe7dc357083459d6dd5b171e12cadb ]

The idea behind the warnings is that the user would get warned in case when more than one priority is configured for a given DSCP value on a netdevice.

The warning is currently wrong, because dcb_ieee_getapp_mask() returns the first matching entry, not all of them, and the warning will then claim that some priority is "current", when in fact it is not.

But more importantly, the warning is misleading in general. Consider the following commands:

 # dcb app flush dev swp19 dscp-prio
 # dcb app add dev swp19 dscp-prio 24:3
 # dcb app replace dev swp19 dscp-prio 24:2

The last command will issue the following warning:

mlxsw_spectrum3 0000:07:00.0 swp19: Ignoring new priority 2 for DSCP 24 in favor of current value of 3

The reason is that the "replace" command works by first adding the new value, and then removing all old values. This is the only way to make the replacement without causing the traffic to be prioritized to whatever the chip defaults to. The warning is issued in response to adding the new priority, and then no warning is shown when the old priority is removed. The upshot is that the canonical way to change traffic prioritization always produces a warning about ignoring the new priority, but what gets configured is in fact what the user intended.

An option to just emit warning every time that the prioritization changes just to make it clear that it happened is obviously unsatisfactory.

Therefore, in this patch, remove the warnings.

---
 drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c | 13 -------------
 1 file changed, 13 deletions(-)
drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c +0 -13
index 5f92b1691360..aff6d4f35cd2 100644
@@ -168,8 +168,6 @@ static int mlxsw_sp_dcbnl_ieee_setets(struct net_device *dev,
 static int mlxsw_sp_dcbnl_app_validate(struct net_device *dev,
 				       struct dcb_app *app)
 {
-	int prio;
-
 	if (app->priority >= IEEE_8021QAZ_MAX_TCS) {
 		netdev_err(dev, "APP entry with priority value %u is invalid\n",
 			   app->priority);
@@ -183,17 +181,6 @@ static int mlxsw_sp_dcbnl_app_validate(struct net_device *dev,
 				   app->protocol);
 			return -EINVAL;
 		}
-
-		/* Warn about any DSCP APP entries with the same PID. */
-		prio = fls(dcb_ieee_getapp_mask(dev, app));
-		if (prio--) {
-			if (prio < app->priority)
-				netdev_warn(dev, "Choosing priority %d for DSCP %d in favor of previously-active value of %d\n",
-					    app->priority, app->protocol, prio);
-			else if (prio > app->priority)
-				netdev_warn(dev, "Ignoring new priority %d for DSCP %d in favor of current value of %d\n",
-					    app->priority, app->protocol, prio);
-		}
 		break;
 
 	case IEEE_8021QAZ_APP_SEL_ETHERTYPE:
Signature · 1 line
2.35.1
author maintainer
#66 lore raw

PATCH 67/135 mlxsw: Treat LLDP packets as control

In reply to Sasha Levin

From: Petr Machata <[email protected]>

[ Upstream commit 0106668cd2f91bf913fb78972840dedfba80a3c3 ]

When trapping packets for on-CPU processing, Spectrum machines differentiate between control and non-control traps. Traffic trapped through non-control traps is treated as data and kept in shared buffer in pools 0-4. Traffic trapped through control traps is kept in the dedicated control buffer 9. The advantage of marking traps as control is that pressure in the data plane does not prevent the control traffic to be processed.

When the LLDP trap was introduced, it was marked as a control trap. But then in commit aed4b5721143 ("mlxsw: spectrum: PTP: Hook into packet receive path"), PTP traps were introduced. Because Ethernet-encapsulated PTP packets look to the Spectrum-1 ASIC as LLDP traffic and are trapped under the LLDP trap, this trap was reconfigured as non-control, in sync with the PTP traps.

There is however no requirement that PTP traffic be handled as data. Besides, the usual encapsulation for PTP traffic is UDP, not bare Ethernet, and that is in deployments that even need PTP, which is far less common than LLDP. This is reflected by the default policer, which was not bumped up to the 19Kpps / 24Kpps that is the expected load of a PTP-enabled Spectrum-1 switch.

Marking of LLDP trap as non-control was therefore probably misguided. In this patch, change it back to control.

---
 drivers/net/ethernet/mellanox/mlxsw/spectrum_trap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlxsw/spectrum_trap.c +1 -1
index 47b061b99160..ed4d0d3448f3 100644
@@ -864,7 +864,7 @@ static const struct mlxsw_sp_trap_item mlxsw_sp_trap_items_arr[] = {
 		.trap = MLXSW_SP_TRAP_CONTROL(LLDP, LLDP, TRAP),
 		.listeners_arr = {
 			MLXSW_RXL(mlxsw_sp_rx_ptp_listener, LLDP, TRAP_TO_CPU,
-				  false, SP_LLDP, DISCARD),
+				  true, SP_LLDP, DISCARD),
 		},
 	},
 	{
Signature · 1 line
2.35.1
author maintainer
#67 lore raw

PATCH 68/135 drm/amdgpu/psp: move PSP memory alloc from hw_init to sw_init

In reply to Sasha Levin

From: Alex Deucher <[email protected]>

[ Upstream commit b95b5391684b39695887afb4a13cccee7820f5d6 ]

Memory allocations should be done in sw_init. hw_init should just be hardware programming needed to initialize the IP block. This is how most other IP blocks work. Move the GPU memory allocations from psp hw_init to psp sw_init and move the memory free to sw_fini. This also fixes a potential GPU memory leak if psp hw_init fails.

---
 drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c | 95 ++++++++++++-------------
 1 file changed, 47 insertions(+), 48 deletions(-)
drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c +47 -48
index dee17a0e1187..786518f7e37b 100644
@@ -331,7 +331,39 @@ static int psp_sw_init(void *handle)
 		}
 	}
 
+	ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
+				      amdgpu_sriov_vf(adev) ?
+				      AMDGPU_GEM_DOMAIN_VRAM : AMDGPU_GEM_DOMAIN_GTT,
+				      &psp->fw_pri_bo,
+				      &psp->fw_pri_mc_addr,
+				      &psp->fw_pri_buf);
+	if (ret)
+		return ret;
+
+	ret = amdgpu_bo_create_kernel(adev, PSP_FENCE_BUFFER_SIZE, PAGE_SIZE,
+				      AMDGPU_GEM_DOMAIN_VRAM,
+				      &psp->fence_buf_bo,
+				      &psp->fence_buf_mc_addr,
+				      &psp->fence_buf);
+	if (ret)
+		goto failed1;
+
+	ret = amdgpu_bo_create_kernel(adev, PSP_CMD_BUFFER_SIZE, PAGE_SIZE,
+				      AMDGPU_GEM_DOMAIN_VRAM,
+				      &psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
+				      (void **)&psp->cmd_buf_mem);
+	if (ret)
+		goto failed2;
+
 	return 0;
+
+failed2:
+	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
+			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
+failed1:
+	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
+			      &psp->fence_buf_mc_addr, &psp->fence_buf);
+	return ret;
 }
 
 static int psp_sw_fini(void *handle)
@@ -361,6 +393,13 @@ static int psp_sw_fini(void *handle)
 	kfree(cmd);
 	cmd = NULL;
 
+	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
+			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
+	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
+			      &psp->fence_buf_mc_addr, &psp->fence_buf);
+	amdgpu_bo_free_kernel(&psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
+			      (void **)&psp->cmd_buf_mem);
+
 	return 0;
 }
 
@@ -2391,51 +2430,18 @@ static int psp_load_fw(struct amdgpu_device *adev)
 	struct psp_context *psp = &adev->psp;
 
 	if (amdgpu_sriov_vf(adev) && amdgpu_in_reset(adev)) {
-		psp_ring_stop(psp, PSP_RING_TYPE__KM); /* should not destroy ring, only stop */
-		goto skip_memalloc;
-	}
-
-	if (amdgpu_sriov_vf(adev)) {
-		ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
-						AMDGPU_GEM_DOMAIN_VRAM,
-						&psp->fw_pri_bo,
-						&psp->fw_pri_mc_addr,
-						&psp->fw_pri_buf);
+		/* should not destroy ring, only stop */
+		psp_ring_stop(psp, PSP_RING_TYPE__KM);
 	} else {
-		ret = amdgpu_bo_create_kernel(adev, PSP_1_MEG, PSP_1_MEG,
-						AMDGPU_GEM_DOMAIN_GTT,
-						&psp->fw_pri_bo,
-						&psp->fw_pri_mc_addr,
-						&psp->fw_pri_buf);
-	}
-
-	if (ret)
-		goto failed;
-
-	ret = amdgpu_bo_create_kernel(adev, PSP_FENCE_BUFFER_SIZE, PAGE_SIZE,
-					AMDGPU_GEM_DOMAIN_VRAM,
-					&psp->fence_buf_bo,
-					&psp->fence_buf_mc_addr,
-					&psp->fence_buf);
-	if (ret)
-		goto failed;
-
-	ret = amdgpu_bo_create_kernel(adev, PSP_CMD_BUFFER_SIZE, PAGE_SIZE,
-				      AMDGPU_GEM_DOMAIN_VRAM,
-				      &psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
-				      (void **)&psp->cmd_buf_mem);
-	if (ret)
-		goto failed;
+		memset(psp->fence_buf, 0, PSP_FENCE_BUFFER_SIZE);
 
-	memset(psp->fence_buf, 0, PSP_FENCE_BUFFER_SIZE);
-
-	ret = psp_ring_init(psp, PSP_RING_TYPE__KM);
-	if (ret) {
-		DRM_ERROR("PSP ring init failed!\n");
-		goto failed;
+		ret = psp_ring_init(psp, PSP_RING_TYPE__KM);
+		if (ret) {
+			DRM_ERROR("PSP ring init failed!\n");
+			goto failed;
+		}
 	}
 
-skip_memalloc:
 	ret = psp_hw_start(psp);
 	if (ret)
 		goto failed;
@@ -2553,13 +2559,6 @@ static int psp_hw_fini(void *handle)
 	psp_tmr_terminate(psp);
 	psp_ring_destroy(psp, PSP_RING_TYPE__KM);
 
-	amdgpu_bo_free_kernel(&psp->fw_pri_bo,
-			      &psp->fw_pri_mc_addr, &psp->fw_pri_buf);
-	amdgpu_bo_free_kernel(&psp->fence_buf_bo,
-			      &psp->fence_buf_mc_addr, &psp->fence_buf);
-	amdgpu_bo_free_kernel(&psp->cmd_buf_bo, &psp->cmd_buf_mc_addr,
-			      (void **)&psp->cmd_buf_mem);
-
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#68 lore raw

PATCH 69/135 drm/amdgpu/ucode: Remove firmware load type check in amdgpu_ucode_free_bo

In reply to Sasha Levin

From: Alice Wong <[email protected]>

[ Upstream commit ab0cd4a9ae5b4679b714d8dbfedc0901fecdce9f ]

When psp_hw_init failed, it will set the load_type to AMDGPU_FW_LOAD_DIRECT. During amdgpu_device_ip_fini, amdgpu_ucode_free_bo checks that load_type is AMDGPU_FW_LOAD_DIRECT and skips deallocating fw_buf causing memory leak. Remove load_type check in amdgpu_ucode_free_bo.

---
 drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c +1 -2
index ca3350502618..aebafbc327fb 100644
@@ -714,8 +714,7 @@ int amdgpu_ucode_create_bo(struct amdgpu_device *adev)
 
 void amdgpu_ucode_free_bo(struct amdgpu_device *adev)
 {
-	if (adev->firmware.load_type != AMDGPU_FW_LOAD_DIRECT)
-		amdgpu_bo_free_kernel(&adev->firmware.fw_buf,
+	amdgpu_bo_free_kernel(&adev->firmware.fw_buf,
 		&adev->firmware.fw_buf_mc,
 		&adev->firmware.fw_buf_ptr);
 }
Signature · 1 line
2.35.1
author maintainer
#69 lore raw

PATCH 70/135 regulator: mt6315: Enforce regulator-compatible, not name

In reply to Sasha Levin

From: Nícolas F. R. A. Prado <[email protected]>

[ Upstream commit 6d435a94ba5bb4f2ad381c0828fbae89c66b50fe ]

The MT6315 PMIC dt-binding should enforce that one of the valid regulator-compatible is set in each regulator node. However it was mistakenly matching against regulator-name instead.

Fix the typo. This not only fixes the compatible verification, but also lifts the regulator-name restriction, so that more meaningful names can be set for each platform.

---
 .../devicetree/bindings/regulator/mt6315-regulator.yaml         | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/devicetree/bindings/regulator/mt6315-regulator.yaml +1 -1
index 61dd5af80db6..5d2d989de893 100644
@@ -31,7 +31,7 @@ properties:
         $ref: "regulator.yaml#"
 
         properties:
-          regulator-name:
+          regulator-compatible:
             pattern: "^vbuck[1-4]$"
 
     additionalProperties: false
Signature · 7 lines
2.35.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#70 lore raw

PATCH 71/135 HID: bigben: fix slab-out-of-bounds Write in bigben_probe

In reply to Sasha Levin

From: Dongliang Mu <[email protected]>

[ Upstream commit fc4ef9d5724973193bfa5ebed181dba6de3a56db ]

There is a slab-out-of-bounds Write bug in hid-bigbenff driver. The problem is the driver assumes the device must have an input but some malicious devices violate this assumption.

Fix this by checking hid_device's input is non-empty before its usage.

---
 drivers/hid/hid-bigbenff.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/hid/hid-bigbenff.c +6 -0
index 74ad8bf98bfd..e8c5e3ac9fff 100644
@@ -347,6 +347,12 @@ static int bigben_probe(struct hid_device *hid,
 	bigben->report = list_entry(report_list->next,
 		struct hid_report, list);
 
+	if (list_empty(&hid->inputs)) {
+		hid_err(hid, "no inputs found\n");
+		error = -ENODEV;
+		goto error_hw_stop;
+	}
+
 	hidinput = list_first_entry(&hid->inputs, struct hid_input, list);
 	set_bit(FF_RUMBLE, hidinput->input->ffbit);
 
Signature · 1 line
2.35.1
author maintainer
#71 lore raw

PATCH 72/135 drm/tegra: gem: Do not try to dereference ERR_PTR()

In reply to Sasha Levin

From: Thierry Reding <[email protected]>

[ Upstream commit cb7e1abc2c73633e1eefa168ab2dad6e838899c9 ]

When mapping the DMA-BUF attachment fails, map->sgt will be an ERR_PTR- encoded error code and the cleanup code would try to free that memory, which obviously would fail.

Zero out that pointer after extracting the error code when this happens so that kfree() can do the right thing.

---
 drivers/gpu/drm/tegra/gem.c | 1 +
 1 file changed, 1 insertion(+)
drivers/gpu/drm/tegra/gem.c +1 -0
index fce0e52973c2..9810b3bdd342 100644
@@ -88,6 +88,7 @@ static struct host1x_bo_mapping *tegra_bo_pin(struct device *dev, struct host1x_
 		if (IS_ERR(map->sgt)) {
 			dma_buf_detach(buf, map->attach);
 			err = PTR_ERR(map->sgt);
+			map->sgt = NULL;
 			goto free;
 		}
 
Signature · 1 line
2.35.1
author maintainer
#72 lore raw

PATCH 73/135 of: Support more than one crash kernel regions for kexec -s

In reply to Sasha Levin

From: Zhen Lei <[email protected]>

[ Upstream commit 8af6b91f58341325bf74ecb0389ddc0039091d84 ]

When "crashkernel=X,high" is used, there may be two crash regions:
high=crashk_res and low=crashk_low_res. But now the syscall kexec_file_load() only add crashk_res into "linux,usable-memory-range", this may cause the second kernel to have no available dma memory.

Fix it like kexec-tools does for option -c, add both 'high' and 'low' regions into the dtb.

---
 drivers/of/kexec.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/of/kexec.c +9 -0
index b9bd1cff1793..8d374cc552be 100644
@@ -386,6 +386,15 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 				crashk_res.end - crashk_res.start + 1);
 		if (ret)
 			goto out;
+
+		if (crashk_low_res.end) {
+			ret = fdt_appendprop_addrrange(fdt, 0, chosen_node,
+					"linux,usable-memory-range",
+					crashk_low_res.start,
+					crashk_low_res.end - crashk_low_res.start + 1);
+			if (ret)
+				goto out;
+		}
 	}
 
 	/* add bootargs */
Signature · 1 line
2.35.1
author maintainer
#73 lore raw

PATCH 74/135 ASoC: tscs454: Add endianness flag in snd_soc_component_driver

In reply to Sasha Levin

From: Charles Keepax <[email protected]>

[ Upstream commit ff69ec96b87dccb3a29edef8cec5d4fefbbc2055 ]

The endianness flag is used on the CODEC side to specify an ambivalence to endian, typically because it is lost over the hardware link. This device receives audio over an I2S DAI and as such should have endianness applied.

A fixup is also required to use the width directly rather than relying on the format in hw_params, now both little and big endian would be supported. It is worth noting this changes the behaviour of S24_LE to use a word length of 24 rather than 32. This would appear to be a correction since the fact S24_LE is stored as 32 bits should not be presented over the bus.

---
 sound/soc/codecs/tscs454.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
sound/soc/codecs/tscs454.c +6 -6
index 43220bb36701..c27ca9a273e1 100644
@@ -3120,18 +3120,17 @@ static int set_aif_sample_format(struct snd_soc_component *component,
 	unsigned int width;
 	int ret;
 
-	switch (format) {
-	case SNDRV_PCM_FORMAT_S16_LE:
+	switch (snd_pcm_format_width(format)) {
+	case 16:
 		width = FV_WL_16;
 		break;
-	case SNDRV_PCM_FORMAT_S20_3LE:
+	case 20:
 		width = FV_WL_20;
 		break;
-	case SNDRV_PCM_FORMAT_S24_3LE:
+	case 24:
 		width = FV_WL_24;
 		break;
-	case SNDRV_PCM_FORMAT_S24_LE:
-	case SNDRV_PCM_FORMAT_S32_LE:
+	case 32:
 		width = FV_WL_32;
 		break;
 	default:
@@ -3326,6 +3325,7 @@ static const struct snd_soc_component_driver soc_component_dev_tscs454 = {
 	.num_dapm_routes = ARRAY_SIZE(tscs454_intercon),
 	.controls =	tscs454_snd_controls,
 	.num_controls = ARRAY_SIZE(tscs454_snd_controls),
+	.endianness = 1,
 };
 
 #define TSCS454_RATES SNDRV_PCM_RATE_8000_96000
Signature · 1 line
2.35.1
author maintainer
#74 lore raw

PATCH 75/135 net/mlx5: Increase FW pre-init timeout for health recovery

In reply to Sasha Levin

From: Gavin Li <[email protected]>

[ Upstream commit 37ca95e62ee23fa6d2c2c64e3dc40b4a0c0146dc ]

Currently, health recovery will reload driver to recover it from fatal errors. During the driver's load process, it would wait for FW to set the pre-init bit for up to 120 seconds, beyond this threshold it would abort the load process. In some cases, such as a FW upgrade on the DPU, this timeout period is insufficient, and the user has no way to recover the host device.

To solve this issue, introduce a new FW pre-init timeout for health recovery, which is set to 2 hours.

The timeout for devlink reload and probe will use the original one because they are user triggered flows, and therefore should not have a significantly long timeout, during which the user command would hang.

---
 .../net/ethernet/mellanox/mlx5/core/devlink.c |  4 ++--
 .../ethernet/mellanox/mlx5/core/fw_reset.c    |  2 +-
 .../ethernet/mellanox/mlx5/core/lib/tout.c    |  1 +
 .../ethernet/mellanox/mlx5/core/lib/tout.h    |  1 +
 .../net/ethernet/mellanox/mlx5/core/main.c    | 23 +++++++++++--------
 .../ethernet/mellanox/mlx5/core/mlx5_core.h   |  2 +-
 6 files changed, 20 insertions(+), 13 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/devlink.c +2 -2
index d1093bb2d436..5e432e4fc381 100644
@@ -182,13 +182,13 @@ static int mlx5_devlink_reload_up(struct devlink *devlink, enum devlink_reload_a
 	*actions_performed = BIT(action);
 	switch (action) {
 	case DEVLINK_RELOAD_ACTION_DRIVER_REINIT:
-		return mlx5_load_one(dev);
+		return mlx5_load_one(dev, false);
 	case DEVLINK_RELOAD_ACTION_FW_ACTIVATE:
 		if (limit == DEVLINK_RELOAD_LIMIT_NO_RESET)
 			break;
 		/* On fw_activate action, also driver is reloaded and reinit performed */
 		*actions_performed |= BIT(DEVLINK_RELOAD_ACTION_DRIVER_REINIT);
-		return mlx5_load_one(dev);
+		return mlx5_load_one(dev, false);
 	default:
 		/* Unsupported action should not get to this function */
 		WARN_ON(1);
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c +1 -1
index 1c771287bee5..d5f540132a0e 100644
@@ -106,7 +106,7 @@ static void mlx5_fw_reset_complete_reload(struct mlx5_core_dev *dev)
 	if (test_bit(MLX5_FW_RESET_FLAGS_PENDING_COMP, &fw_reset->reset_flags)) {
 		complete(&fw_reset->done);
 	} else {
-		mlx5_load_one(dev);
+		mlx5_load_one(dev, false);
 		devlink_remote_reload_actions_performed(priv_to_devlink(dev), 0,
 							BIT(DEVLINK_RELOAD_ACTION_DRIVER_REINIT) |
 							BIT(DEVLINK_RELOAD_ACTION_FW_ACTIVATE));
drivers/net/ethernet/mellanox/mlx5/core/lib/tout.c +1 -0
index c1df0d3595d8..d758848d34d0 100644
@@ -10,6 +10,7 @@ struct mlx5_timeouts {
 
 static const u32 tout_def_sw_val[MAX_TIMEOUT_TYPES] = {
 	[MLX5_TO_FW_PRE_INIT_TIMEOUT_MS] = 120000,
+	[MLX5_TO_FW_PRE_INIT_ON_RECOVERY_TIMEOUT_MS] = 7200000,
 	[MLX5_TO_FW_PRE_INIT_WARN_MESSAGE_INTERVAL_MS] = 20000,
 	[MLX5_TO_FW_PRE_INIT_WAIT_MS] = 2,
 	[MLX5_TO_FW_INIT_MS] = 2000,
drivers/net/ethernet/mellanox/mlx5/core/lib/tout.h +1 -0
index 1c42ead782fa..257c03eeab36 100644
@@ -7,6 +7,7 @@
 enum mlx5_timeouts_types {
 	/* pre init timeouts (not read from FW) */
 	MLX5_TO_FW_PRE_INIT_TIMEOUT_MS,
+	MLX5_TO_FW_PRE_INIT_ON_RECOVERY_TIMEOUT_MS,
 	MLX5_TO_FW_PRE_INIT_WARN_MESSAGE_INTERVAL_MS,
 	MLX5_TO_FW_PRE_INIT_WAIT_MS,
 
drivers/net/ethernet/mellanox/mlx5/core/main.c +14 -9
index 4e49dca94bc3..56a8079dc16a 100644
@@ -1015,7 +1015,7 @@ static void mlx5_cleanup_once(struct mlx5_core_dev *dev)
 	mlx5_devcom_unregister_device(dev->priv.devcom);
 }
 
-static int mlx5_function_setup(struct mlx5_core_dev *dev, bool boot)
+static int mlx5_function_setup(struct mlx5_core_dev *dev, u64 timeout)
 {
 	int err;
 
@@ -1030,11 +1030,11 @@ static int mlx5_function_setup(struct mlx5_core_dev *dev, bool boot)
 
 	/* wait for firmware to accept initialization segments configurations
 	 */
-	err = wait_fw_init(dev, mlx5_tout_ms(dev, FW_PRE_INIT_TIMEOUT),
+	err = wait_fw_init(dev, timeout,
 			   mlx5_tout_ms(dev, FW_PRE_INIT_WARN_MESSAGE_INTERVAL));
 	if (err) {
 		mlx5_core_err(dev, "Firmware over %llu MS in pre-initializing state, aborting\n",
-			      mlx5_tout_ms(dev, FW_PRE_INIT_TIMEOUT));
+			      timeout);
 		return err;
 	}
 
@@ -1297,7 +1297,7 @@ int mlx5_init_one(struct mlx5_core_dev *dev)
 	mutex_lock(&dev->intf_state_mutex);
 	dev->state = MLX5_DEVICE_STATE_UP;
 
-	err = mlx5_function_setup(dev, true);
+	err = mlx5_function_setup(dev, mlx5_tout_ms(dev, FW_PRE_INIT_TIMEOUT));
 	if (err)
 		goto err_function;
 
@@ -1361,9 +1361,10 @@ void mlx5_uninit_one(struct mlx5_core_dev *dev)
 	mutex_unlock(&dev->intf_state_mutex);
 }
 
-int mlx5_load_one(struct mlx5_core_dev *dev)
+int mlx5_load_one(struct mlx5_core_dev *dev, bool recovery)
 {
 	int err = 0;
+	u64 timeout;
 
 	mutex_lock(&dev->intf_state_mutex);
 	if (test_bit(MLX5_INTERFACE_STATE_UP, &dev->intf_state)) {
@@ -1373,7 +1374,11 @@ int mlx5_load_one(struct mlx5_core_dev *dev)
 	/* remove any previous indication of internal error */
 	dev->state = MLX5_DEVICE_STATE_UP;
 
-	err = mlx5_function_setup(dev, false);
+	if (recovery)
+		timeout = mlx5_tout_ms(dev, FW_PRE_INIT_ON_RECOVERY_TIMEOUT);
+	else
+		timeout = mlx5_tout_ms(dev, FW_PRE_INIT_TIMEOUT);
+	err = mlx5_function_setup(dev, timeout);
 	if (err)
 		goto err_function;
 
@@ -1746,7 +1751,7 @@ static void mlx5_pci_resume(struct pci_dev *pdev)
 
 	mlx5_pci_trace(dev, "Enter, loading driver..\n");
 
-	err = mlx5_load_one(dev);
+	err = mlx5_load_one(dev, false);
 
 	mlx5_pci_trace(dev, "Done, err = %d, device %s\n", err,
 		       !err ? "recovered" : "Failed");
@@ -1833,7 +1838,7 @@ static int mlx5_resume(struct pci_dev *pdev)
 {
 	struct mlx5_core_dev *dev = pci_get_drvdata(pdev);
 
-	return mlx5_load_one(dev);
+	return mlx5_load_one(dev, false);
 }
 
 static const struct pci_device_id mlx5_core_pci_table[] = {
@@ -1878,7 +1883,7 @@ int mlx5_recover_device(struct mlx5_core_dev *dev)
 			return -EIO;
 	}
 
-	return mlx5_load_one(dev);
+	return mlx5_load_one(dev, true);
 }
 
 static struct pci_driver mlx5_core_driver = {
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.h +1 -1
index 6f8baa0f2a73..2d2150fc7a0f 100644
@@ -290,7 +290,7 @@ void mlx5_mdev_uninit(struct mlx5_core_dev *dev);
 int mlx5_init_one(struct mlx5_core_dev *dev);
 void mlx5_uninit_one(struct mlx5_core_dev *dev);
 void mlx5_unload_one(struct mlx5_core_dev *dev);
-int mlx5_load_one(struct mlx5_core_dev *dev);
+int mlx5_load_one(struct mlx5_core_dev *dev, bool recovery);
 
 int mlx5_vport_get_other_func_cap(struct mlx5_core_dev *dev, u16 function_id, void *out);
 
Signature · 1 line
2.35.1
author maintainer
#75 lore raw

PATCH 76/135 scsi: hisi_sas: Undo RPM resume for failed notify phy event for v3 HW

In reply to Sasha Levin

From: Xiang Chen <[email protected]>

[ Upstream commit 9b5387fe5af38116b452259d87cd66594b6277c1 ]

If we fail to notify the phy up event then undo the RPM resume, as the phy up notify event handling pairs with that RPM resume.

---
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c +8 -2
index 52089538e9de..b309a9d0f5b7 100644
@@ -1561,9 +1561,15 @@ static irqreturn_t phy_up_v3_hw(int phy_no, struct hisi_hba *hisi_hba)
 
 	phy->port_id = port_id;
 
-	/* Call pm_runtime_put_sync() with pairs in hisi_sas_phyup_pm_work() */
+	/*
+	 * Call pm_runtime_get_noresume() which pairs with
+	 * hisi_sas_phyup_pm_work() -> pm_runtime_put_sync().
+	 * For failure call pm_runtime_put() as we are in a hardirq context.
+	 */
 	pm_runtime_get_noresume(dev);
-	hisi_sas_notify_phy_event(phy, HISI_PHYE_PHY_UP_PM);
+	res = hisi_sas_notify_phy_event(phy, HISI_PHYE_PHY_UP_PM);
+	if (!res)
+		pm_runtime_put(dev);
 
 	res = IRQ_HANDLED;
 
Signature · 1 line
2.35.1
author maintainer
#76 lore raw

PATCH 77/135 scsi: lpfc: Alter FPIN stat accounting logic

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit e6f51041450282a8668af3a8fc5c7744e81a447c ]

When configuring CMF management based on signals instead of FPINs, FPIN alarm and warning statistics are not tracked.

Change the behavior so that FPIN alarms and warnings are always tracked regardless of the configured mode.

Similar changes are made in the CMF signal stat accounting logic. Upon receipt of a signal, only track signaled alarms and warnings. FPIN stats should not be incremented upon receipt of a signal.

---
 drivers/scsi/lpfc/lpfc_els.c  | 49 +++++++++++------------------------
 drivers/scsi/lpfc/lpfc_init.c | 22 ++--------------
 2 files changed, 17 insertions(+), 54 deletions(-)
drivers/scsi/lpfc/lpfc_els.c +15 -34
index f936833c9909..8d416019f59f 100644
@@ -3784,9 +3784,6 @@ lpfc_least_capable_settings(struct lpfc_hba *phba,
 {
 	u32 rsp_sig_cap = 0, drv_sig_cap = 0;
 	u32 rsp_sig_freq_cyc = 0, rsp_sig_freq_scale = 0;
-	struct lpfc_cgn_info *cp;
-	u32 crc;
-	u16 sig_freq;
 
 	/* Get rsp signal and frequency capabilities.  */
 	rsp_sig_cap = be32_to_cpu(pcgd->xmt_signal_capability);
@@ -3842,25 +3839,7 @@ lpfc_least_capable_settings(struct lpfc_hba *phba,
 		}
 	}
 
-	if (!phba->cgn_i)
-		return;
-
-	/* Update signal frequency in congestion info buffer */
-	cp = (struct lpfc_cgn_info *)phba->cgn_i->virt;
-
-	/* Frequency (in ms) Signal Warning/Signal Congestion Notifications
-	 * are received by the HBA
-	 */
-	sig_freq = phba->cgn_sig_freq;
-
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY)
-		cp->cgn_warn_freq = cpu_to_le16(sig_freq);
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-		cp->cgn_alarm_freq = cpu_to_le16(sig_freq);
-		cp->cgn_warn_freq = cpu_to_le16(sig_freq);
-	}
-	crc = lpfc_cgn_calc_crc32(cp, LPFC_CGN_INFO_SZ, LPFC_CGN_CRC32_SEED);
-	cp->cgn_info_crc = cpu_to_le32(crc);
+	/* We are NOT recording signal frequency in congestion info buffer */
 	return;
 
 out_no_support:
@@ -9606,11 +9585,14 @@ lpfc_els_rcv_fpin_cgn(struct lpfc_hba *phba, struct fc_tlv_desc *tlv)
 			/* Take action here for an Alarm event */
 			if (phba->cmf_active_mode != LPFC_CFG_OFF) {
 				if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_ALARM) {
-					/* Track of alarm cnt for cgn_info */
-					atomic_inc(&phba->cgn_fabric_alarm_cnt);
 					/* Track of alarm cnt for SYNC_WQE */
 					atomic_inc(&phba->cgn_sync_alarm_cnt);
 				}
+				/* Track alarm cnt for cgn_info regardless
+				 * of whether CMF is configured for Signals
+				 * or FPINs.
+				 */
+				atomic_inc(&phba->cgn_fabric_alarm_cnt);
 				goto cleanup;
 			}
 			break;
@@ -9618,11 +9600,14 @@ lpfc_els_rcv_fpin_cgn(struct lpfc_hba *phba, struct fc_tlv_desc *tlv)
 			/* Take action here for a Warning event */
 			if (phba->cmf_active_mode != LPFC_CFG_OFF) {
 				if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_WARN) {
-					/* Track of warning cnt for cgn_info */
-					atomic_inc(&phba->cgn_fabric_warn_cnt);
 					/* Track of warning cnt for SYNC_WQE */
 					atomic_inc(&phba->cgn_sync_warn_cnt);
 				}
+				/* Track warning cnt and freq for cgn_info
+				 * regardless of whether CMF is configured for
+				 * Signals or FPINs.
+				 */
+				atomic_inc(&phba->cgn_fabric_warn_cnt);
 cleanup:
 				/* Save frequency in ms */
 				phba->cgn_fpin_frequency =
@@ -9631,14 +9616,10 @@ lpfc_els_rcv_fpin_cgn(struct lpfc_hba *phba, struct fc_tlv_desc *tlv)
 				if (phba->cgn_i) {
 					cp = (struct lpfc_cgn_info *)
 						phba->cgn_i->virt;
-					if (phba->cgn_reg_fpin &
-						LPFC_CGN_FPIN_ALARM)
-						cp->cgn_alarm_freq =
-							cpu_to_le16(value);
-					if (phba->cgn_reg_fpin &
-						LPFC_CGN_FPIN_WARN)
-						cp->cgn_warn_freq =
-							cpu_to_le16(value);
+					cp->cgn_alarm_freq =
+						cpu_to_le16(value);
+					cp->cgn_warn_freq =
+						cpu_to_le16(value);
 					crc = lpfc_cgn_calc_crc32
 						(cp,
 						LPFC_CGN_INFO_SZ,
drivers/scsi/lpfc/lpfc_init.c +2 -20
index 6739bdd8195d..7e4a8848a12c 100644
@@ -5877,21 +5877,8 @@ lpfc_cgn_save_evt_cnt(struct lpfc_hba *phba)
 
 	/* Use the frequency found in the last rcv'ed FPIN */
 	value = phba->cgn_fpin_frequency;
-	if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_WARN)
-		cp->cgn_warn_freq = cpu_to_le16(value);
-	if (phba->cgn_reg_fpin & LPFC_CGN_FPIN_ALARM)
-		cp->cgn_alarm_freq = cpu_to_le16(value);
-
-	/* Frequency (in ms) Signal Warning/Signal Congestion Notifications
-	 * are received by the HBA
-	 */
-	value = phba->cgn_sig_freq;
-
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY ||
-	    phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM)
-		cp->cgn_warn_freq = cpu_to_le16(value);
-	if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM)
-		cp->cgn_alarm_freq = cpu_to_le16(value);
+	cp->cgn_warn_freq = cpu_to_le16(value);
+	cp->cgn_alarm_freq = cpu_to_le16(value);
 
 	lvalue = lpfc_cgn_calc_crc32(cp, LPFC_CGN_INFO_SZ,
 				     LPFC_CGN_CRC32_SEED);
@@ -6606,9 +6593,6 @@ lpfc_sli4_async_sli_evt(struct lpfc_hba *phba, struct lpfc_acqe_sli *acqe_sli)
 		/* Alarm overrides warning, so check that first */
 		if (cgn_signal->alarm_cnt) {
 			if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-				/* Keep track of alarm cnt for cgn_info */
-				atomic_add(cgn_signal->alarm_cnt,
-					   &phba->cgn_fabric_alarm_cnt);
 				/* Keep track of alarm cnt for CMF_SYNC_WQE */
 				atomic_add(cgn_signal->alarm_cnt,
 					   &phba->cgn_sync_alarm_cnt);
@@ -6617,8 +6601,6 @@ lpfc_sli4_async_sli_evt(struct lpfc_hba *phba, struct lpfc_acqe_sli *acqe_sli)
 			/* signal action needs to be taken */
 			if (phba->cgn_reg_signal == EDC_CG_SIG_WARN_ONLY ||
 			    phba->cgn_reg_signal == EDC_CG_SIG_WARN_ALARM) {
-				/* Keep track of warning cnt for cgn_info */
-				atomic_add(cnt, &phba->cgn_fabric_warn_cnt);
 				/* Keep track of warning cnt for CMF_SYNC_WQE */
 				atomic_add(cnt, &phba->cgn_sync_warn_cnt);
 			}
Signature · 1 line
2.35.1
author maintainer
#77 lore raw

PATCH 78/135 net: remove two BUG() from skb_checksum_help()

In reply to Sasha Levin

From: Eric Dumazet <[email protected]>

[ Upstream commit d7ea0d9df2a6265b2b180d17ebc64b38105968fc ]

I have a syzbot report that managed to get a crash in skb_checksum_help()

If syzbot can trigger these BUG(), it makes sense to replace them with more friendly WARN_ON_ONCE() since skb_checksum_help() can instead return an error code.

Note that syzbot will still crash there, until real bug is fixed.

---
 net/core/dev.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
net/core/dev.c +6 -2
index 80dbbd5f6a73..178400e4d13e 100644
@@ -3156,11 +3156,15 @@ int skb_checksum_help(struct sk_buff *skb)
 	}
 
 	offset = skb_checksum_start_offset(skb);
-	BUG_ON(offset >= skb_headlen(skb));
+	ret = -EINVAL;
+	if (WARN_ON_ONCE(offset >= skb_headlen(skb)))
+		goto out;
+
 	csum = skb_checksum(skb, offset, skb->len - offset, 0);
 
 	offset += skb->csum_offset;
-	BUG_ON(offset + sizeof(__sum16) > skb_headlen(skb));
+	if (WARN_ON_ONCE(offset + sizeof(__sum16) > skb_headlen(skb)))
+		goto out;
 
 	ret = skb_ensure_writable(skb, offset + sizeof(__sum16));
 	if (ret)
Signature · 1 line
2.35.1
author maintainer
#78 lore raw

PATCH 79/135 s390/preempt: disable __preempt_count_add() optimization for PROFILE_ALL_BRANCHES

In reply to Sasha Levin

From: Heiko Carstens <[email protected]>

[ Upstream commit 63678eecec57fc51b778be3da35a397931287170 ]

gcc 12 does not (always) optimize away code that should only be generated if parameters are constant and within in a certain range. This depends on various obscure kernel config options, however in particular PROFILE_ALL_BRANCHES can trigger this compile error:

In function ‘__atomic_add_const’,

    inlined from ‘__preempt_count_add.part.0’ at ./arch/s390/include/asm/preempt.h:50:3:
./arch/s390/include/asm/atomic_ops.h:80:9: error: impossible constraint in ‘asm’
   80 |         asm volatile(                                                   \
      |         ^~~

Workaround this by simply disabling the optimization for PROFILE_ALL_BRANCHES, since the kernel will be so slow, that this optimization won't matter at all.

---
 arch/s390/include/asm/preempt.h | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)
arch/s390/include/asm/preempt.h +11 -4
index d9d5350cc3ec..bf15da0fedbc 100644
@@ -46,10 +46,17 @@ static inline bool test_preempt_need_resched(void)
 
 static inline void __preempt_count_add(int val)
 {
-	if (__builtin_constant_p(val) && (val >= -128) && (val <= 127))
-		__atomic_add_const(val, &S390_lowcore.preempt_count);
-	else
-		__atomic_add(val, &S390_lowcore.preempt_count);
+	/*
+	 * With some obscure config options and CONFIG_PROFILE_ALL_BRANCHES
+	 * enabled, gcc 12 fails to handle __builtin_constant_p().
+	 */
+	if (!IS_ENABLED(CONFIG_PROFILE_ALL_BRANCHES)) {
+		if (__builtin_constant_p(val) && (val >= -128) && (val <= 127)) {
+			__atomic_add_const(val, &S390_lowcore.preempt_count);
+			return;
+		}
+	}
+	__atomic_add(val, &S390_lowcore.preempt_count);
 }
 
 static inline void __preempt_count_sub(int val)
Signature · 1 line
2.35.1
author maintainer
#79 lore raw

PATCH 80/135 perf/amd/ibs: Cascade pmu init functions' return value

In reply to Sasha Levin

From: Ravi Bangoria <[email protected]>

[ Upstream commit 39b2ca75eec8a33e2ffdb8aa0c4840ec3e3b472c ]

IBS pmu initialization code ignores return value provided by callee functions. Fix it.

---
 arch/x86/events/amd/ibs.c | 37 +++++++++++++++++++++++++++++--------
 1 file changed, 29 insertions(+), 8 deletions(-)
arch/x86/events/amd/ibs.c +29 -8
index 9739019d4b67..367ca899e6e8 100644
@@ -759,9 +759,10 @@ static __init int perf_ibs_pmu_init(struct perf_ibs *perf_ibs, char *name)
 	return ret;
 }
 
-static __init void perf_event_ibs_init(void)
+static __init int perf_event_ibs_init(void)
 {
 	struct attribute **attr = ibs_op_format_attrs;
+	int ret;
 
 	/*
 	 * Some chips fail to reset the fetch count when it is written; instead
@@ -773,7 +774,9 @@ static __init void perf_event_ibs_init(void)
 	if (boot_cpu_data.x86 == 0x19 && boot_cpu_data.x86_model < 0x10)
 		perf_ibs_fetch.fetch_ignore_if_zero_rip = 1;
 
-	perf_ibs_pmu_init(&perf_ibs_fetch, "ibs_fetch");
+	ret = perf_ibs_pmu_init(&perf_ibs_fetch, "ibs_fetch");
+	if (ret)
+		return ret;
 
 	if (ibs_caps & IBS_CAPS_OPCNT) {
 		perf_ibs_op.config_mask |= IBS_OP_CNT_CTL;
@@ -786,15 +789,35 @@ static __init void perf_event_ibs_init(void)
 		perf_ibs_op.cnt_mask    |= IBS_OP_MAX_CNT_EXT_MASK;
 	}
 
-	perf_ibs_pmu_init(&perf_ibs_op, "ibs_op");
+	ret = perf_ibs_pmu_init(&perf_ibs_op, "ibs_op");
+	if (ret)
+		goto err_op;
+
+	ret = register_nmi_handler(NMI_LOCAL, perf_ibs_nmi_handler, 0, "perf_ibs");
+	if (ret)
+		goto err_nmi;
 
-	register_nmi_handler(NMI_LOCAL, perf_ibs_nmi_handler, 0, "perf_ibs");
 	pr_info("perf: AMD IBS detected (0x%08x)\n", ibs_caps);
+	return 0;
+
+err_nmi:
+	perf_pmu_unregister(&perf_ibs_op.pmu);
+	free_percpu(perf_ibs_op.pcpu);
+	perf_ibs_op.pcpu = NULL;
+err_op:
+	perf_pmu_unregister(&perf_ibs_fetch.pmu);
+	free_percpu(perf_ibs_fetch.pcpu);
+	perf_ibs_fetch.pcpu = NULL;
+
+	return ret;
 }
 
 #else /* defined(CONFIG_PERF_EVENTS) && defined(CONFIG_CPU_SUP_AMD) */
 
-static __init void perf_event_ibs_init(void) { }
+static __init int perf_event_ibs_init(void)
+{
+	return 0;
+}
 
 #endif
 
@@ -1064,9 +1087,7 @@ static __init int amd_ibs_init(void)
 			  x86_pmu_amd_ibs_starting_cpu,
 			  x86_pmu_amd_ibs_dying_cpu);
 
-	perf_event_ibs_init();
-
-	return 0;
+	return perf_event_ibs_init();
 }
 
 /* Since we need the pci subsystem to init ibs we can't do this earlier: */
Signature · 1 line
2.35.1
author maintainer
#80 lore raw

PATCH 81/135 sched/core: Avoid obvious double update_rq_clock warning

In reply to Sasha Levin

From: Hao Jia <[email protected]>

[ Upstream commit 2679a83731d51a744657f718fc02c3b077e47562 ]

When we use raw_spin_rq_lock() to acquire the rq lock and have to update the rq clock while holding the lock, the kernel may issue a WARN_DOUBLE_CLOCK warning.

Since we directly use raw_spin_rq_lock() to acquire rq lock instead of rq_lock(), there is no corresponding change to rq->clock_update_flags. In particular, we have obtained the rq lock of other CPUs, the rq->clock_update_flags of this CPU may be RQCF_UPDATED at this time, and then calling update_rq_clock() will trigger the WARN_DOUBLE_CLOCK warning.

So we need to clear RQCF_UPDATED of rq->clock_update_flags to avoid the WARN_DOUBLE_CLOCK warning.

For the sched_rt_period_timer() and migrate_task_rq_dl() cases we simply replace raw_spin_rq_lock()/raw_spin_rq_unlock() with rq_lock()/rq_unlock().

For the {pull,push}_{rt,dl}_task() cases, we add the double_rq_clock_clear_update() function to clear RQCF_UPDATED of rq->clock_update_flags, and call double_rq_clock_clear_update() before double_lock_balance()/double_rq_lock() returns to avoid the WARN_DOUBLE_CLOCK warning.

Some call trace reports:
Call Trace 1:

 <IRQ>
 sched_rt_period_timer+0x10f/0x3a0
 ? enqueue_top_rt_rq+0x110/0x110
 __hrtimer_run_queues+0x1a9/0x490
 hrtimer_interrupt+0x10b/0x240
 __sysvec_apic_timer_interrupt+0x8a/0x250
 sysvec_apic_timer_interrupt+0x9a/0xd0
 </IRQ>
 <TASK>
 asm_sysvec_apic_timer_interrupt+0x12/0x20

Call Trace 2:

 <TASK>
 activate_task+0x8b/0x110
 push_rt_task.part.108+0x241/0x2c0
 push_rt_tasks+0x15/0x30
 finish_task_switch+0xaa/0x2e0
 ? __switch_to+0x134/0x420
 __schedule+0x343/0x8e0
 ? hrtimer_start_range_ns+0x101/0x340
 schedule+0x4e/0xb0
 do_nanosleep+0x8e/0x160
 hrtimer_nanosleep+0x89/0x120
 ? hrtimer_init_sleeper+0x90/0x90
 __x64_sys_nanosleep+0x96/0xd0
 do_syscall_64+0x34/0x90
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Call Trace 3:

 <TASK>
 deactivate_task+0x93/0xe0
 pull_rt_task+0x33e/0x400
 balance_rt+0x7e/0x90
 __schedule+0x62f/0x8e0
 do_task_dead+0x3f/0x50
 do_exit+0x7b8/0xbb0
 do_group_exit+0x2d/0x90
 get_signal+0x9df/0x9e0
 ? preempt_count_add+0x56/0xa0
 ? __remove_hrtimer+0x35/0x70
 arch_do_signal_or_restart+0x36/0x720
 ? nanosleep_copyout+0x39/0x50
 ? do_nanosleep+0x131/0x160
 ? audit_filter_inodes+0xf5/0x120
 exit_to_user_mode_prepare+0x10f/0x1e0
 syscall_exit_to_user_mode+0x17/0x30
 do_syscall_64+0x40/0x90
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Call Trace 4:

 update_rq_clock+0x128/0x1a0
 migrate_task_rq_dl+0xec/0x310
 set_task_cpu+0x84/0x1e4
 try_to_wake_up+0x1d8/0x5c0
 wake_up_process+0x1c/0x30
 hrtimer_wakeup+0x24/0x3c
 __hrtimer_run_queues+0x114/0x270
 hrtimer_interrupt+0xe8/0x244
 arch_timer_handler_phys+0x30/0x50
 handle_percpu_devid_irq+0x88/0x140
 generic_handle_domain_irq+0x40/0x60
 gic_handle_irq+0x48/0xe0
 call_on_irq_stack+0x2c/0x60
 do_interrupt_handler+0x80/0x84

Steps to reproduce:
1. Enable CONFIG_SCHED_DEBUG when compiling the kernel
2. echo 1 > /sys/kernel/debug/clear_warn_once
echo "WARN_DOUBLE_CLOCK" > /sys/kernel/debug/sched/features echo "NO_RT_PUSH_IPI" > /sys/kernel/debug/sched/features
3. Run some rt/dl tasks that periodically work and sleep, e.g. Create 2*n rt or dl (90% running) tasks via rt-app (on a system with n CPUs), and Dietmar Eggemann reports Call Trace 4 when running on PREEMPT_RT kernel.

---
 kernel/sched/core.c     |  6 +++---
 kernel/sched/deadline.c |  5 +++--
 kernel/sched/rt.c       |  5 +++--
 kernel/sched/sched.h    | 28 ++++++++++++++++++++++++----
 4 files changed, 33 insertions(+), 11 deletions(-)
kernel/sched/core.c +3 -3
index 1eec4925b8c6..a6722496ed5f 100644
@@ -546,10 +546,10 @@ void double_rq_lock(struct rq *rq1, struct rq *rq2)
 		swap(rq1, rq2);
 
 	raw_spin_rq_lock(rq1);
-	if (__rq_lockp(rq1) == __rq_lockp(rq2))
-		return;
+	if (__rq_lockp(rq1) != __rq_lockp(rq2))
+		raw_spin_rq_lock_nested(rq2, SINGLE_DEPTH_NESTING);
 
-	raw_spin_rq_lock_nested(rq2, SINGLE_DEPTH_NESTING);
+	double_rq_clock_clear_update(rq1, rq2);
 }
 #endif
 
kernel/sched/deadline.c +3 -2
index 62f0cf842277..1571b775ec15 100644
@@ -1804,6 +1804,7 @@ select_task_rq_dl(struct task_struct *p, int cpu, int flags)
 
 static void migrate_task_rq_dl(struct task_struct *p, int new_cpu __maybe_unused)
 {
+	struct rq_flags rf;
 	struct rq *rq;
 
 	if (READ_ONCE(p->__state) != TASK_WAKING)
@@ -1815,7 +1816,7 @@ static void migrate_task_rq_dl(struct task_struct *p, int new_cpu __maybe_unused
 	 * from try_to_wake_up(). Hence, p->pi_lock is locked, but
 	 * rq->lock is not... So, lock it
 	 */
-	raw_spin_rq_lock(rq);
+	rq_lock(rq, &rf);
 	if (p->dl.dl_non_contending) {
 		update_rq_clock(rq);
 		sub_running_bw(&p->dl, &rq->dl);
@@ -1831,7 +1832,7 @@ static void migrate_task_rq_dl(struct task_struct *p, int new_cpu __maybe_unused
 			put_task_struct(p);
 	}
 	sub_rq_bw(&p->dl, &rq->dl);
-	raw_spin_rq_unlock(rq);
+	rq_unlock(rq, &rf);
 }
 
 static void check_preempt_equal_dl(struct rq *rq, struct task_struct *p)
kernel/sched/rt.c +3 -2
index 14f273c29518..3b8a7e153367 100644
@@ -885,6 +885,7 @@ static int do_sched_rt_period_timer(struct rt_bandwidth *rt_b, int overrun)
 		int enqueue = 0;
 		struct rt_rq *rt_rq = sched_rt_period_rt_rq(rt_b, i);
 		struct rq *rq = rq_of_rt_rq(rt_rq);
+		struct rq_flags rf;
 		int skip;
 
 		/*
@@ -899,7 +900,7 @@ static int do_sched_rt_period_timer(struct rt_bandwidth *rt_b, int overrun)
 		if (skip)
 			continue;
 
-		raw_spin_rq_lock(rq);
+		rq_lock(rq, &rf);
 		update_rq_clock(rq);
 
 		if (rt_rq->rt_time) {
@@ -937,7 +938,7 @@ static int do_sched_rt_period_timer(struct rt_bandwidth *rt_b, int overrun)
 
 		if (enqueue)
 			sched_rt_rq_enqueue(rt_rq);
-		raw_spin_rq_unlock(rq);
+		rq_unlock(rq, &rf);
 	}
 
 	if (!throttled && (!rt_bandwidth_enabled() || rt_b->rt_runtime == RUNTIME_INF))
kernel/sched/sched.h +24 -4
index e8a5549488dd..3887f4aea160 100644
@@ -2494,6 +2494,24 @@ unsigned long arch_scale_freq_capacity(int cpu)
 }
 #endif
 
+#ifdef CONFIG_SCHED_DEBUG
+/*
+ * In double_lock_balance()/double_rq_lock(), we use raw_spin_rq_lock() to
+ * acquire rq lock instead of rq_lock(). So at the end of these two functions
+ * we need to call double_rq_clock_clear_update() to clear RQCF_UPDATED of
+ * rq->clock_update_flags to avoid the WARN_DOUBLE_CLOCK warning.
+ */
+static inline void double_rq_clock_clear_update(struct rq *rq1, struct rq *rq2)
+{
+	rq1->clock_update_flags &= (RQCF_REQ_SKIP|RQCF_ACT_SKIP);
+	/* rq1 == rq2 for !CONFIG_SMP, so just clear RQCF_UPDATED once. */
+#ifdef CONFIG_SMP
+	rq2->clock_update_flags &= (RQCF_REQ_SKIP|RQCF_ACT_SKIP);
+#endif
+}
+#else
+static inline void double_rq_clock_clear_update(struct rq *rq1, struct rq *rq2) {}
+#endif
 
 #ifdef CONFIG_SMP
 
@@ -2559,14 +2577,15 @@ static inline int _double_lock_balance(struct rq *this_rq, struct rq *busiest)
 	__acquires(busiest->lock)
 	__acquires(this_rq->lock)
 {
-	if (__rq_lockp(this_rq) == __rq_lockp(busiest))
-		return 0;
-
-	if (likely(raw_spin_rq_trylock(busiest)))
+	if (__rq_lockp(this_rq) == __rq_lockp(busiest) ||
+	    likely(raw_spin_rq_trylock(busiest))) {
+		double_rq_clock_clear_update(this_rq, busiest);
 		return 0;
+	}
 
 	if (rq_order_less(this_rq, busiest)) {
 		raw_spin_rq_lock_nested(busiest, SINGLE_DEPTH_NESTING);
+		double_rq_clock_clear_update(this_rq, busiest);
 		return 0;
 	}
 
@@ -2660,6 +2679,7 @@ static inline void double_rq_lock(struct rq *rq1, struct rq *rq2)
 	BUG_ON(rq1 != rq2);
 	raw_spin_rq_lock(rq1);
 	__acquire(rq2->lock);	/* Fake it out ;) */
+	double_rq_clock_clear_update(rq1, rq2);
 }
 
 /*
Signature · 1 line
2.35.1
author maintainer
#81 lore raw

PATCH 82/135 spi: stm32-qspi: Fix wait_cmd timeout in APM mode

In reply to Sasha Levin

From: Patrice Chotard <[email protected]>

[ Upstream commit d83d89ea68b4726700fa87b22db075e4217e691c ]

In APM mode, TCF and TEF flags are not set. To avoid timeout in stm32_qspi_wait_cmd(), don't check if TCF/TEF are set.

---
 drivers/spi/spi-stm32-qspi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/spi/spi-stm32-qspi.c +2 -1
index ffdc55f87e82..dd38cb8ffbc2 100644
@@ -308,7 +308,8 @@ static int stm32_qspi_wait_cmd(struct stm32_qspi *qspi,
 	if (!op->data.nbytes)
 		goto wait_nobusy;
 
-	if (readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF)
+	if ((readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF) ||
+	    qspi->fmode == CCR_FMODE_APM)
 		goto out;
 
 	reinit_completion(&qspi->data_completion);
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#82 lore raw

PATCH 83/135 dma-debug: change allocation mode from GFP_NOWAIT to GFP_ATIOMIC

In reply to Sasha Levin

From: Mikulas Patocka <[email protected]>

[ Upstream commit 84bc4f1dbbbb5f8aa68706a96711dccb28b518e5 ]

We observed the error "cacheline tracking ENOMEM, dma-debug disabled" during a light system load (copying some files). The reason for this error is that the dma_active_cacheline radix tree uses GFP_NOWAIT allocation - so it can't access the emergency memory reserves and it fails as soon as anybody reaches the watermark.

This patch changes GFP_NOWAIT to GFP_ATOMIC, so that it can access the emergency memory reserves.

---
 kernel/dma/debug.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/dma/debug.c +1 -1
index f8ff598596b8..ac740630c79c 100644
@@ -448,7 +448,7 @@ void debug_dma_dump_mappings(struct device *dev)
  * other hand, consumes a single dma_debug_entry, but inserts 'nents'
  * entries into the tree.
  */
-static RADIX_TREE(dma_active_cacheline, GFP_NOWAIT);
+static RADIX_TREE(dma_active_cacheline, GFP_ATOMIC);
 static DEFINE_SPINLOCK(radix_lock);
 #define ACTIVE_CACHELINE_MAX_OVERLAP ((1 << RADIX_TREE_MAX_TAGS) - 1)
 #define CACHELINE_PER_PAGE_SHIFT (PAGE_SHIFT - L1_CACHE_SHIFT)
Signature · 6 lines
2.35.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#83 lore raw

PATCH 84/135 ASoC: SOF: amd: add missing platform_device_unregister in acp_pci_rn_probe

In reply to Sasha Levin

From: Zheng Bin <[email protected]>

[ Upstream commit cbcab8cd737c74c20195c31d647e19f7cb49c9b8 ]

acp_pci_rn_probe misses a call platform_device_unregister in error path, this patch fixes that.

---
 sound/soc/sof/amd/pci-rn.c | 1 +
 1 file changed, 1 insertion(+)
sound/soc/sof/amd/pci-rn.c +1 -0
index 392ffbdf6417..d809d151a38c 100644
@@ -93,6 +93,7 @@ static int acp_pci_rn_probe(struct pci_dev *pci, const struct pci_device_id *pci
 	res = devm_kzalloc(&pci->dev, sizeof(struct resource) * ARRAY_SIZE(renoir_res), GFP_KERNEL);
 	if (!res) {
 		sof_pci_remove(pci);
+		platform_device_unregister(dmic_dev);
 		return -ENOMEM;
 	}
 
Signature · 1 line
2.35.1
author maintainer
#84 lore raw

PATCH 85/135 ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default

In reply to Sasha Levin

From: Mario Limonciello <[email protected]>

[ Upstream commit d52848620de00cde4a3a5df908e231b8c8868250 ]

ASUS B1400CEAE fails to resume from suspend to idle by default. This was bisected back to commit df4f9bc4fb9c ("nvme-pci: add support for ACPI StorageD3Enable property") but this is a red herring to the problem.

Before this commit the system wasn't getting into deepest sleep state. Presumably this commit is allowing entry into deepest sleep state as advertised by firmware, but there are some other problems related to the wakeup.

As it is confirmed the system works properly with S3, set the default for this system to S3.

---
 drivers/acpi/sleep.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/acpi/sleep.c +12 -0
index d4fbea91ab6b..8a5cb115fea8 100644
@@ -373,6 +373,18 @@ static const struct dmi_system_id acpisleep_dmi_table[] __initconst = {
 		DMI_MATCH(DMI_PRODUCT_NAME, "20GGA00L00"),
 		},
 	},
+	/*
+	 * ASUS B1400CEAE hangs on resume from suspend (see
+	 * https://bugzilla.kernel.org/show_bug.cgi?id=215742).
+	 */
+	{
+	.callback = init_default_s3,
+	.ident = "ASUS B1400CEAE",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+		DMI_MATCH(DMI_PRODUCT_NAME, "ASUS EXPERTBOOK B1400CEAE"),
+		},
+	},
 	{},
 };
 
Signature · 1 line
2.35.1
author maintainer
#85 lore raw

PATCH 86/135 ipmi:ssif: Check for NULL msg when handling events and messages

In reply to Sasha Levin

From: Corey Minyard <[email protected]>

[ Upstream commit 7602b957e2404e5f98d9a40b68f1fd27f0028712 ]

Even though it's not possible to get into the SSIF_GETTING_MESSAGES and SSIF_GETTING_EVENTS states without a valid message in the msg field, it's probably best to be defensive here and check and print a log, since that means something else went wrong.

Also add a default clause to that switch statement to release the lock and print a log, in case the state variable gets messed up somehow.

---
 drivers/char/ipmi/ipmi_ssif.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)
drivers/char/ipmi/ipmi_ssif.c +23 -0
index 48aab77abebf..588610236de1 100644
@@ -814,6 +814,14 @@ static void msg_done_handler(struct ssif_info *ssif_info, int result,
 		break;
 
 	case SSIF_GETTING_EVENTS:
+		if (!msg) {
+			/* Should never happen, but just in case. */
+			dev_warn(&ssif_info->client->dev,
+				 "No message set while getting events\n");
+			ipmi_ssif_unlock_cond(ssif_info, flags);
+			break;
+		}
+
 		if ((result < 0) || (len < 3) || (msg->rsp[2] != 0)) {
 			/* Error getting event, probably done. */
 			msg->done(msg);
@@ -838,6 +846,14 @@ static void msg_done_handler(struct ssif_info *ssif_info, int result,
 		break;
 
 	case SSIF_GETTING_MESSAGES:
+		if (!msg) {
+			/* Should never happen, but just in case. */
+			dev_warn(&ssif_info->client->dev,
+				 "No message set while getting messages\n");
+			ipmi_ssif_unlock_cond(ssif_info, flags);
+			break;
+		}
+
 		if ((result < 0) || (len < 3) || (msg->rsp[2] != 0)) {
 			/* Error getting event, probably done. */
 			msg->done(msg);
@@ -861,6 +877,13 @@ static void msg_done_handler(struct ssif_info *ssif_info, int result,
 			deliver_recv_msg(ssif_info, msg);
 		}
 		break;
+
+	default:
+		/* Should never happen, but just in case. */
+		dev_warn(&ssif_info->client->dev,
+			 "Invalid state in message done handling: %d\n",
+			 ssif_info->ssif_state);
+		ipmi_ssif_unlock_cond(ssif_info, flags);
 	}
 
 	flags = ipmi_ssif_lock_cond(ssif_info, &oflags);
Signature · 1 line
2.35.1
author maintainer
#86 lore raw

PATCH 87/135 ipmi: Add an intializer for ipmi_smi_msg struct

In reply to Sasha Levin

From: Corey Minyard <[email protected]>

[ Upstream commit 9824117dd964ecebf5d81990dbf21dfb56445049 ]

There was a "type" element added to this structure, but some static values were missed. The default value will be zero, which is correct, but create an initializer for the type and initialize the type properly in the initializer to avoid future issues.

---
 drivers/char/ipmi/ipmi_poweroff.c |  4 +---
 drivers/char/ipmi/ipmi_watchdog.c | 14 +++++---------
 include/linux/ipmi_smi.h          |  6 ++++++
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/char/ipmi/ipmi_poweroff.c +1 -3
index bc3a18daf97a..62e71c46ac5f 100644
@@ -94,9 +94,7 @@ static void dummy_recv_free(struct ipmi_recv_msg *msg)
 {
 	atomic_dec(&dummy_count);
 }
-static struct ipmi_smi_msg halt_smi_msg = {
-	.done = dummy_smi_free
-};
+static struct ipmi_smi_msg halt_smi_msg = INIT_IPMI_SMI_MSG(dummy_smi_free);
 static struct ipmi_recv_msg halt_recv_msg = {
 	.done = dummy_recv_free
 };
drivers/char/ipmi/ipmi_watchdog.c +5 -9
index 883b4a341012..8e536ce0a5d2 100644
@@ -354,9 +354,7 @@ static void msg_free_recv(struct ipmi_recv_msg *msg)
 			complete(&msg_wait);
 	}
 }
-static struct ipmi_smi_msg smi_msg = {
-	.done = msg_free_smi
-};
+static struct ipmi_smi_msg smi_msg = INIT_IPMI_SMI_MSG(msg_free_smi);
 static struct ipmi_recv_msg recv_msg = {
 	.done = msg_free_recv
 };
@@ -475,9 +473,8 @@ static void panic_recv_free(struct ipmi_recv_msg *msg)
 	atomic_dec(&panic_done_count);
 }
 
-static struct ipmi_smi_msg panic_halt_heartbeat_smi_msg = {
-	.done = panic_smi_free
-};
+static struct ipmi_smi_msg panic_halt_heartbeat_smi_msg =
+	INIT_IPMI_SMI_MSG(panic_smi_free);
 static struct ipmi_recv_msg panic_halt_heartbeat_recv_msg = {
 	.done = panic_recv_free
 };
@@ -516,9 +513,8 @@ static void panic_halt_ipmi_heartbeat(void)
 		atomic_sub(2, &panic_done_count);
 }
 
-static struct ipmi_smi_msg panic_halt_smi_msg = {
-	.done = panic_smi_free
-};
+static struct ipmi_smi_msg panic_halt_smi_msg =
+	INIT_IPMI_SMI_MSG(panic_smi_free);
 static struct ipmi_recv_msg panic_halt_recv_msg = {
 	.done = panic_recv_free
 };
include/linux/ipmi_smi.h +6 -0
index 9277d21c2690..5d69820d8b02 100644
@@ -125,6 +125,12 @@ struct ipmi_smi_msg {
 	void (*done)(struct ipmi_smi_msg *msg);
 };
 
+#define INIT_IPMI_SMI_MSG(done_handler) \
+{						\
+	.done = done_handler,			\
+	.type = IPMI_SMI_MSG_TYPE_NORMAL	\
+}
+
 struct ipmi_smi_handlers {
 	struct module *owner;
 
Signature · 1 line
2.35.1
author maintainer
#87 lore raw

PATCH 88/135 ipmi: Fix pr_fmt to avoid compilation issues

In reply to Sasha Levin

From: Corey Minyard <[email protected]>

[ Upstream commit 2ebaf18a0b7fb764bba6c806af99fe868cee93de ]

The was it was wouldn't work in some situations, simplify it. What was there was unnecessary complexity.

---
 drivers/char/ipmi/ipmi_msghandler.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/char/ipmi/ipmi_msghandler.c +2 -2
index f1827257ef0e..2610e809c802 100644
@@ -11,8 +11,8 @@
  * Copyright 2002 MontaVista Software Inc.
  */
 
-#define pr_fmt(fmt) "%s" fmt, "IPMI message handler: "
-#define dev_fmt pr_fmt
+#define pr_fmt(fmt) "IPMI message handler: " fmt
+#define dev_fmt(fmt) pr_fmt(fmt)
 
 #include <linux/module.h>
 #include <linux/errno.h>
Signature · 1 line
2.35.1
author maintainer
#88 lore raw

PATCH 89/135 kunit: bail out of test filtering logic quicker if OOM

In reply to Sasha Levin

From: Daniel Latypov <[email protected]>

[ Upstream commit a02353f491622e49c7ddedc6a6dc4f1d6ed2150a ]

When filtering what tests to run (suites and/or cases) via kunit.filter_glob (e.g. kunit.py run <glob>), we allocate copies of suites.

These allocations can fail, and we largely don't handle that.
Note: realistically, this probably doesn't matter much. We're not allocating much memory and this happens early in boot, so if we can't do that, then there's likely far bigger problems.

This patch makes us immediately bail out from the top-level function (kunit_filter_suites) with -ENOMEM if any of the underlying kmalloc() calls return NULL.

Implementation note: we used to return NULL pointers from some functions to indicate either that all suites/tests were filtered out or there was an error allocating the new array.

We'll log a short error in this case and not run any tests or print a TAP header. From a kunit.py user's perspective, they'll get a message about missing/invalid TAP output and have to dig into the test.log to see it. Since hitting this error seems so unlikely, it's probably fine to not invent a way to plumb this error message more visibly.

See also: https://lore.kernel.org/linux-kselftest/[email protected]/

---
 lib/kunit/executor.c      | 27 ++++++++++++++++++++++-----
 lib/kunit/executor_test.c |  4 +++-
 2 files changed, 25 insertions(+), 6 deletions(-)
lib/kunit/executor.c +22 -5
index 22640c9ee819..2f73a6a35a7e 100644
@@ -71,9 +71,13 @@ kunit_filter_tests(struct kunit_suite *const suite, const char *test_glob)
 
 	/* Use memcpy to workaround copy->name being const. */
 	copy = kmalloc(sizeof(*copy), GFP_KERNEL);
+	if (!copy)
+		return ERR_PTR(-ENOMEM);
 	memcpy(copy, suite, sizeof(*copy));
 
 	filtered = kcalloc(n + 1, sizeof(*filtered), GFP_KERNEL);
+	if (!filtered)
+		return ERR_PTR(-ENOMEM);
 
 	n = 0;
 	kunit_suite_for_each_test_case(suite, test_case) {
@@ -106,14 +110,16 @@ kunit_filter_subsuite(struct kunit_suite * const * const subsuite,
 
 	filtered = kmalloc_array(n + 1, sizeof(*filtered), GFP_KERNEL);
 	if (!filtered)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	n = 0;
 	for (i = 0; subsuite[i] != NULL; ++i) {
 		if (!glob_match(filter->suite_glob, subsuite[i]->name))
 			continue;
 		filtered_suite = kunit_filter_tests(subsuite[i], filter->test_glob);
-		if (filtered_suite)
+		if (IS_ERR(filtered_suite))
+			return ERR_CAST(filtered_suite);
+		else if (filtered_suite)
 			filtered[n++] = filtered_suite;
 	}
 	filtered[n] = NULL;
@@ -146,7 +152,8 @@ static void kunit_free_suite_set(struct suite_set suite_set)
 }
 
 static struct suite_set kunit_filter_suites(const struct suite_set *suite_set,
-					    const char *filter_glob)
+					    const char *filter_glob,
+					    int *err)
 {
 	int i;
 	struct kunit_suite * const **copy, * const *filtered_subsuite;
@@ -166,6 +173,10 @@ static struct suite_set kunit_filter_suites(const struct suite_set *suite_set,
 
 	for (i = 0; i < max; ++i) {
 		filtered_subsuite = kunit_filter_subsuite(suite_set->start[i], &filter);
+		if (IS_ERR(filtered_subsuite)) {
+			*err = PTR_ERR(filtered_subsuite);
+			return filtered;
+		}
 		if (filtered_subsuite)
 			*copy++ = filtered_subsuite;
 	}
@@ -236,9 +247,15 @@ int kunit_run_all_tests(void)
 		.start = __kunit_suites_start,
 		.end = __kunit_suites_end,
 	};
+	int err;
 
-	if (filter_glob_param)
-		suite_set = kunit_filter_suites(&suite_set, filter_glob_param);
+	if (filter_glob_param) {
+		suite_set = kunit_filter_suites(&suite_set, filter_glob_param, &err);
+		if (err) {
+			pr_err("kunit executor: error filtering suites: %d\n", err);
+			return err;
+		}
+	}
 
 	if (!action_param)
 		kunit_exec_run_tests(&suite_set);
lib/kunit/executor_test.c +3 -1
index 4ed57fd94e42..eac6ff480273 100644
@@ -137,14 +137,16 @@ static void filter_suites_test(struct kunit *test)
 		.end = suites + 2,
 	};
 	struct suite_set filtered = {.start = NULL, .end = NULL};
+	int err = 0;
 
 	/* Emulate two files, each having one suite */
 	subsuites[0][0] = alloc_fake_suite(test, "suite0", dummy_test_cases);
 	subsuites[1][0] = alloc_fake_suite(test, "suite1", dummy_test_cases);
 
 	/* Filter out suite1 */
-	filtered = kunit_filter_suites(&suite_set, "suite0");
+	filtered = kunit_filter_suites(&suite_set, "suite0", &err);
 	kfree_subsuites_at_end(test, &filtered); /* let us use ASSERTs without leaking */
+	KUNIT_EXPECT_EQ(test, err, 0);
 	KUNIT_ASSERT_EQ(test, filtered.end - filtered.start, (ptrdiff_t)1);
 
 	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, filtered.start);
Signature · 1 line
2.35.1
Reviewed-by Brendan Higgins on v1 89/135
#89 lore raw

Re: [PATCH AUTOSEL 5.17 089/135] kunit: bail out of test filtering logic quicker if OOM

Quoted 5 lines · Sasha Levin

From: Daniel Latypov <[email protected]>

[ Upstream commit a02353f491622e49c7ddedc6a6dc4f1d6ed2150a ]

Is it possible to make sure the fix for this commit gets picked up as well [1]? I was waiting a bit to see if it was going to get picked up automatically, but I don't see such an email yet:
https://lore.kernel.org/stable/?q=kunit+OOM
(Perhaps the automation just hasn't gotten around to it yet?)

Alternatively, reverting just this commit would also work, if that's easier.

[1] commit 1b11063d32d7e11366e48be64215ff517ce32217

Author: Daniel Latypov <[email protected]>
Date:   Fri May 13 11:37:07 2022 -0700

kunit: fix executor OOM error handling logic on non-UML

The existing logic happens to work fine on UML, but is not correct when running on other arches.

1. We didn't initialize int err, and kunit_filter_suites() doesn't explicitly set it to 0 on success. So we had false "failures".
Note: it doesn't happen on UML, causing this to get overlooked.
2. If we error out, we do not call kunit_handle_shutdown(). This makes kunit.py timeout when using a non-UML arch, since the QEMU process doesn't ever exit.

Fixes a02353f49162 ("kunit: bail out of test filtering logic

quicker if OOM")

Without 1b11063d32d7 above, this "fix" breaks more cases than it fixes due to my sloppiness.

Thanks,
Daniel

author maintainer
#90 lore raw

Re: [PATCH AUTOSEL 5.17 089/135] kunit: bail out of test filtering logic quicker if OOM

Quoted 4 lines · Daniel Latypov
Quoted 3 lines · Sasha Levin

From: Daniel Latypov <[email protected]>

Quoted 8 lines
Quoted 2 lines

[ Upstream commit a02353f491622e49c7ddedc6a6dc4f1d6ed2150a ]

Is it possible to make sure the fix for this commit gets picked up as well [1]? I was waiting a bit to see if it was going to get picked up automatically, but I don't see such an email yet:
https://lore.kernel.org/stable/?q=kunit+OOM
(Perhaps the automation just hasn't gotten around to it yet?)

I'll make sure the fix added along with this commit.

Signature · 2 lines
Thanks,
Sasha
#91 lore raw

Re: [PATCH AUTOSEL 5.17 089/135] kunit: bail out of test filtering logic quicker if OOM

Quoted 9 lines · Sasha Levin
Quoted 7 lines · Daniel Latypov
Quoted 5 lines · Sasha Levin

From: Daniel Latypov <[email protected]>

[ Upstream commit a02353f491622e49c7ddedc6a6dc4f1d6ed2150a ]

Quoted 7 lines
Quoted 5 lines

Is it possible to make sure the fix for this commit gets picked up as well [1]? I was waiting a bit to see if it was going to get picked up automatically, but I don't see such an email yet:
https://lore.kernel.org/stable/?q=kunit+OOM
(Perhaps the automation just hasn't gotten around to it yet?)

I'll make sure the fix added along with this commit.

I just saw the emails about it being added to the 5.{17,18} stable trees.

Thanks a bunch!
Daniel

author maintainer
#92 lore raw

PATCH 90/135 rtlwifi: Use pr_warn instead of WARN_ONCE

In reply to Sasha Levin

From: Dongliang Mu <[email protected]>

[ Upstream commit ad732da434a2936128769216eddaece3b1af4588 ]

This memory allocation failure can be triggered by fault injection or high pressure testing, resulting a WARN.

Fix this by replacing WARN with pr_warn.

---
 drivers/net/wireless/realtek/rtlwifi/usb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/realtek/rtlwifi/usb.c +1 -1
index 86a236873254..a8eebafb9a7e 100644
@@ -1014,7 +1014,7 @@ int rtl_usb_probe(struct usb_interface *intf,
 	hw = ieee80211_alloc_hw(sizeof(struct rtl_priv) +
 				sizeof(struct rtl_usb_priv), &rtl_ops);
 	if (!hw) {
-		WARN_ONCE(true, "rtl_usb: ieee80211 alloc failed\n");
+		pr_warn("rtl_usb: ieee80211 alloc failed\n");
 		return -ENOMEM;
 	}
 	rtlpriv = hw->priv;
Signature · 1 line
2.35.1
author maintainer
#93 lore raw

PATCH 91/135 mt76: mt7921: accept rx frames with non-standard VHT MCS10-11

In reply to Sasha Levin

From: Felix Fietkau <[email protected]>

[ Upstream commit 3128ea016965ce9f91ddf4e1dd944724462d1698 ]

The hardware receives them properly, they should not be dropped

---
 drivers/net/wireless/mediatek/mt76/mt7921/mac.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/mediatek/mt76/mt7921/mac.c +1 -1
index 84f72dd1bf93..e07707f518a2 100644
@@ -698,7 +698,7 @@ mt7921_mac_fill_rx(struct mt7921_dev *dev, struct sk_buff *skb)
 			status->nss =
 				FIELD_GET(MT_PRXV_NSTS, v0) + 1;
 			status->encoding = RX_ENC_VHT;
-			if (i > 9)
+			if (i > 11)
 				return -EINVAL;
 			break;
 		case MT_PHY_TYPE_HE_MU:
Signature · 7 lines
2.35.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#94 lore raw

PATCH 92/135 mt76: fix encap offload ethernet type check

In reply to Sasha Levin

From: Felix Fietkau <[email protected]>

[ Upstream commit bc98e7fdd80d215b4b55eea001023231eb8ce12e ]

The driver needs to check if the format is 802.2 vs 802.3 in order to set a tx descriptor flag. skb->protocol can't be used, since it may not be properly initialized for packets coming in from a packet socket.
Fix misdetection by checking the ethertype from the skb data instead

---
 drivers/net/wireless/mediatek/mt76/mt7915/mac.c | 4 +++-
 drivers/net/wireless/mediatek/mt76/mt7921/mac.c | 4 +++-
 2 files changed, 6 insertions(+), 2 deletions(-)
drivers/net/wireless/mediatek/mt76/mt7915/mac.c +3 -1
index e4c300aa1526..efc04f7a3c71 100644
@@ -982,6 +982,7 @@ mt7915_mac_write_txwi_8023(struct mt7915_dev *dev, __le32 *txwi,
 
 	u8 tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
 	u8 fc_type, fc_stype;
+	u16 ethertype;
 	bool wmm = false;
 	u32 val;
 
@@ -995,7 +996,8 @@ mt7915_mac_write_txwi_8023(struct mt7915_dev *dev, __le32 *txwi,
 	val = FIELD_PREP(MT_TXD1_HDR_FORMAT, MT_HDR_FORMAT_802_3) |
 	      FIELD_PREP(MT_TXD1_TID, tid);
 
-	if (be16_to_cpu(skb->protocol) >= ETH_P_802_3_MIN)
+	ethertype = get_unaligned_be16(&skb->data[12]);
+	if (ethertype >= ETH_P_802_3_MIN)
 		val |= MT_TXD1_ETH_802_3;
 
 	txwi[1] |= cpu_to_le32(val);
drivers/net/wireless/mediatek/mt76/mt7921/mac.c +3 -1
index e07707f518a2..eac2d85b5864 100644
@@ -816,6 +816,7 @@ mt7921_mac_write_txwi_8023(struct mt7921_dev *dev, __le32 *txwi,
 {
 	u8 tid = skb->priority & IEEE80211_QOS_CTL_TID_MASK;
 	u8 fc_type, fc_stype;
+	u16 ethertype;
 	bool wmm = false;
 	u32 val;
 
@@ -829,7 +830,8 @@ mt7921_mac_write_txwi_8023(struct mt7921_dev *dev, __le32 *txwi,
 	val = FIELD_PREP(MT_TXD1_HDR_FORMAT, MT_HDR_FORMAT_802_3) |
 	      FIELD_PREP(MT_TXD1_TID, tid);
 
-	if (be16_to_cpu(skb->protocol) >= ETH_P_802_3_MIN)
+	ethertype = get_unaligned_be16(&skb->data[12]);
+	if (ethertype >= ETH_P_802_3_MIN)
 		val |= MT_TXD1_ETH_802_3;
 
 	txwi[1] |= cpu_to_le32(val);
Signature · 7 lines
2.35.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#95 lore raw

PATCH 93/135 media: rga: fix possible memory leak in rga_probe

In reply to Sasha Levin

From: Hangyu Hua <[email protected]>

[ Upstream commit a71eb6025305192e646040cd76ccacb5bd48a1b5 ]

rga->m2m_dev needs to be freed when rga_probe fails.

---
 drivers/media/platform/rockchip/rga/rga.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/media/platform/rockchip/rga/rga.c +4 -2
index 3d3d1062e212..2f8df74ad0fd 100644
@@ -865,7 +865,7 @@ static int rga_probe(struct platform_device *pdev)
 
 	ret = pm_runtime_resume_and_get(rga->dev);
 	if (ret < 0)
-		goto rel_vdev;
+		goto rel_m2m;
 
 	rga->version.major = (rga_read(rga, RGA_VERSION_INFO) >> 24) & 0xFF;
 	rga->version.minor = (rga_read(rga, RGA_VERSION_INFO) >> 20) & 0x0F;
@@ -881,7 +881,7 @@ static int rga_probe(struct platform_device *pdev)
 					   DMA_ATTR_WRITE_COMBINE);
 	if (!rga->cmdbuf_virt) {
 		ret = -ENOMEM;
-		goto rel_vdev;
+		goto rel_m2m;
 	}
 
 	rga->src_mmu_pages =
@@ -918,6 +918,8 @@ static int rga_probe(struct platform_device *pdev)
 free_dma:
 	dma_free_attrs(rga->dev, RGA_CMDBUF_SIZE, rga->cmdbuf_virt,
 		       rga->cmdbuf_phy, DMA_ATTR_WRITE_COMBINE);
+rel_m2m:
+	v4l2_m2m_release(rga->m2m_dev);
 rel_vdev:
 	video_device_release(vfd);
 unreg_v4l2_dev:
Signature · 7 lines
2.35.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
author maintainer
#96 lore raw

PATCH 94/135 media: coda: limit frame interval enumeration to supported encoder frame sizes

In reply to Sasha Levin

From: Philipp Zabel <[email protected]>

[ Upstream commit 67e33dd957880879e785cfea83a3aa24bd5c5577 ]

Let VIDIOC_ENUM_FRAMEINTERVALS return -EINVAL if userspace queries frame intervals for frame sizes unsupported by the encoder. Fixes the following v4l2-compliance failure:

fail: v4l2-test-formats.cpp(123): found frame intervals for invalid size 47x16
fail: v4l2-test-formats.cpp(282): node->codec_mask & STATEFUL_ENCODER
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL

[hverkuil: drop incorrect 'For decoder devices, return -ENOTTY.' in the commit log]

---
 drivers/media/platform/coda/coda-common.c | 20 ++++++++++++++------
 1 file changed, 14 insertions(+), 6 deletions(-)
drivers/media/platform/coda/coda-common.c +14 -6
index a57822b05070..a2cad1830318 100644
@@ -1324,7 +1324,8 @@ static int coda_enum_frameintervals(struct file *file, void *fh,
 				    struct v4l2_frmivalenum *f)
 {
 	struct coda_ctx *ctx = fh_to_ctx(fh);
-	int i;
+	struct coda_q_data *q_data;
+	const struct coda_codec *codec;
 
 	if (f->index)
 		return -EINVAL;
@@ -1333,12 +1334,19 @@ static int coda_enum_frameintervals(struct file *file, void *fh,
 	if (!ctx->vdoa && f->pixel_format == V4L2_PIX_FMT_YUYV)
 		return -EINVAL;
 
-	for (i = 0; i < CODA_MAX_FORMATS; i++) {
-		if (f->pixel_format == ctx->cvd->src_formats[i] ||
-		    f->pixel_format == ctx->cvd->dst_formats[i])
-			break;
+	if (coda_format_normalize_yuv(f->pixel_format) == V4L2_PIX_FMT_YUV420) {
+		q_data = get_q_data(ctx, V4L2_BUF_TYPE_VIDEO_CAPTURE);
+		codec = coda_find_codec(ctx->dev, f->pixel_format,
+					q_data->fourcc);
+	} else {
+		codec = coda_find_codec(ctx->dev, V4L2_PIX_FMT_YUV420,
+					f->pixel_format);
 	}
-	if (i == CODA_MAX_FORMATS)
+	if (!codec)
+		return -EINVAL;
+
+	if (f->width < MIN_W || f->width > codec->max_w ||
+	    f->height < MIN_H || f->height > codec->max_h)
 		return -EINVAL;
 
 	f->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
Signature · 1 line
2.35.1
author maintainer
#97 lore raw

PATCH 95/135 media: hantro: HEVC: unconditionnaly set pps_{cb/cr}_qp_offset values

In reply to Sasha Levin

From: Benjamin Gaignard <[email protected]>

[ Upstream commit 46c836569196f377f87a3657b330cffaf94bd727 ]

Always set pps_cb_qp_offset and pps_cr_qp_offset values in Hantro/G2 register whatever is V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT flag value.
The vendor code does the same to set these values.
This fixes conformance test CAINIT_G_SHARP_3.

Fluster HEVC score is increase by one with this patch.

---
 drivers/staging/media/hantro/hantro_g2_hevc_dec.c | 9 ++-------
 1 file changed, 2 insertions(+), 7 deletions(-)
drivers/staging/media/hantro/hantro_g2_hevc_dec.c +2 -7
index 99d8ea7543da..fab326389261 100644
@@ -180,13 +180,8 @@ static void set_params(struct hantro_ctx *ctx)
 		hantro_reg_write(vpu, &g2_max_cu_qpd_depth, 0);
 	}
 
-	if (pps->flags & V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT) {
-		hantro_reg_write(vpu, &g2_cb_qp_offset, pps->pps_cb_qp_offset);
-		hantro_reg_write(vpu, &g2_cr_qp_offset, pps->pps_cr_qp_offset);
-	} else {
-		hantro_reg_write(vpu, &g2_cb_qp_offset, 0);
-		hantro_reg_write(vpu, &g2_cr_qp_offset, 0);
-	}
+	hantro_reg_write(vpu, &g2_cb_qp_offset, pps->pps_cb_qp_offset);
+	hantro_reg_write(vpu, &g2_cr_qp_offset, pps->pps_cr_qp_offset);
 
 	hantro_reg_write(vpu, &g2_filt_offset_beta, pps->pps_beta_offset_div2);
 	hantro_reg_write(vpu, &g2_filt_offset_tc, pps->pps_tc_offset_div2);
Signature · 1 line
2.35.1
author maintainer
#98 lore raw

PATCH 96/135 media: ccs-core.c: fix failure to call clk_disable_unprepare

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit eca89cf60b040ee2cae693ea72a0364284f3084c ]

Fixes smatch warning:

drivers/media/i2c/ccs/ccs-core.c:1676 ccs_power_on() warn: 'sensor->ext_clk' from clk_prepare_enable() not released on lines: 1606.

---
 drivers/media/i2c/ccs/ccs-core.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/media/i2c/ccs/ccs-core.c +5 -2
index 9158d3ce45c0..1649b7a9ff72 100644
@@ -1603,8 +1603,11 @@ static int ccs_power_on(struct device *dev)
 			usleep_range(1000, 2000);
 		} while (--retry);
 
-		if (!reset)
-			return -EIO;
+		if (!reset) {
+			dev_err(dev, "software reset failed\n");
+			rval = -EIO;
+			goto out_cci_addr_fail;
+		}
 	}
 
 	if (sensor->hwcfg.i2c_addr_alt) {
Signature · 1 line
2.35.1
author maintainer
#99 lore raw

PATCH 97/135 media: imon: reorganize serialization

In reply to Sasha Levin

From: Tetsuo Handa <[email protected]>

[ Upstream commit db264d4c66c0fe007b5d19fd007707cd0697603d ]

Since usb_register_dev() from imon_init_display() from imon_probe() holds minor_rwsem while display_open() which holds driver_lock and ictx->lock is called with minor_rwsem held from usb_open(), holding driver_lock or ictx->lock when calling usb_register_dev() causes circular locking dependency problem.

Since usb_deregister_dev() from imon_disconnect() holds minor_rwsem while display_open() which holds driver_lock is called with minor_rwsem held, holding driver_lock when calling usb_deregister_dev() also causes circular locking dependency problem.

Sean Young explained that the problem is there are imon devices which have two usb interfaces, even though it is one device. The probe and disconnect function of both usb interfaces can run concurrently.

Alan Stern responded that the driver and USB cores guarantee that when an interface is probed, both the interface and its USB device are locked. Ditto for when the disconnect callback gets run. So concurrent probing/ disconnection of multiple interfaces on the same device is not possible.

Therefore, we don't need locks for handling race between imon_probe() and imon_disconnect(). But we still need to handle race between display_open() /vfd_write()/lcd_write()/display_close() and imon_disconnect(), for disconnect event can happen while file descriptors are in use.

Since "struct file"->private_data is set by display_open(), vfd_write()/ lcd_write()/display_close() can assume that "struct file"->private_data is not NULL even after usb_set_intfdata(interface, NULL) was called.

Replace insufficiently held driver_lock with refcount_t based management. Add a boolean flag for recording whether imon_disconnect() was already called. Use RCU for accessing this boolean flag and refcount_t.

Since the boolean flag for imon_disconnect() is shared, disconnect event on either intf0 or intf1 affects both interfaces. But I assume that this change does not matter, for usually disconnect event would not happen while interfaces are in use.

---
 drivers/media/rc/imon.c | 99 +++++++++++++++++++----------------------
 1 file changed, 47 insertions(+), 52 deletions(-)
drivers/media/rc/imon.c +47 -52
index 54da6f60079b..ab090663f975 100644
@@ -153,6 +153,24 @@ struct imon_context {
 	const struct imon_usb_dev_descr *dev_descr;
 					/* device description with key */
 					/* table for front panels */
+	/*
+	 * Fields for deferring free_imon_context().
+	 *
+	 * Since reference to "struct imon_context" is stored into
+	 * "struct file"->private_data, we need to remember
+	 * how many file descriptors might access this "struct imon_context".
+	 */
+	refcount_t users;
+	/*
+	 * Use a flag for telling display_open()/vfd_write()/lcd_write() that
+	 * imon_disconnect() was already called.
+	 */
+	bool disconnected;
+	/*
+	 * We need to wait for RCU grace period in order to allow
+	 * display_open() to safely check ->disconnected and increment ->users.
+	 */
+	struct rcu_head rcu;
 };
 
 #define TOUCH_TIMEOUT	(HZ/30)
@@ -160,18 +178,18 @@ struct imon_context {
 /* vfd character device file operations */
 static const struct file_operations vfd_fops = {
 	.owner		= THIS_MODULE,
-	.open		= &display_open,
-	.write		= &vfd_write,
-	.release	= &display_close,
+	.open		= display_open,
+	.write		= vfd_write,
+	.release	= display_close,
 	.llseek		= noop_llseek,
 };
 
 /* lcd character device file operations */
 static const struct file_operations lcd_fops = {
 	.owner		= THIS_MODULE,
-	.open		= &display_open,
-	.write		= &lcd_write,
-	.release	= &display_close,
+	.open		= display_open,
+	.write		= lcd_write,
+	.release	= display_close,
 	.llseek		= noop_llseek,
 };
 
@@ -439,9 +457,6 @@ static struct usb_driver imon_driver = {
 	.id_table	= imon_usb_id_table,
 };
 
-/* to prevent races between open() and disconnect(), probing, etc */
-static DEFINE_MUTEX(driver_lock);
-
 /* Module bookkeeping bits */
 MODULE_AUTHOR(MOD_AUTHOR);
 MODULE_DESCRIPTION(MOD_DESC);
@@ -481,9 +496,11 @@ static void free_imon_context(struct imon_context *ictx)
 	struct device *dev = ictx->dev;
 
 	usb_free_urb(ictx->tx_urb);
+	WARN_ON(ictx->dev_present_intf0);
 	usb_free_urb(ictx->rx_urb_intf0);
+	WARN_ON(ictx->dev_present_intf1);
 	usb_free_urb(ictx->rx_urb_intf1);
-	kfree(ictx);
+	kfree_rcu(ictx, rcu);
 
 	dev_dbg(dev, "%s: iMON context freed\n", __func__);
 }
@@ -499,9 +516,6 @@ static int display_open(struct inode *inode, struct file *file)
 	int subminor;
 	int retval = 0;
 
-	/* prevent races with disconnect */
-	mutex_lock(&driver_lock);
-
 	subminor = iminor(inode);
 	interface = usb_find_interface(&imon_driver, subminor);
 	if (!interface) {
@@ -509,13 +523,16 @@ static int display_open(struct inode *inode, struct file *file)
 		retval = -ENODEV;
 		goto exit;
 	}
-	ictx = usb_get_intfdata(interface);
 
-	if (!ictx) {
+	rcu_read_lock();
+	ictx = usb_get_intfdata(interface);
+	if (!ictx || ictx->disconnected || !refcount_inc_not_zero(&ictx->users)) {
+		rcu_read_unlock();
 		pr_err("no context found for minor %d\n", subminor);
 		retval = -ENODEV;
 		goto exit;
 	}
+	rcu_read_unlock();
 
 	mutex_lock(&ictx->lock);
 
@@ -533,8 +550,10 @@ static int display_open(struct inode *inode, struct file *file)
 
 	mutex_unlock(&ictx->lock);
 
+	if (retval && refcount_dec_and_test(&ictx->users))
+		free_imon_context(ictx);
+
 exit:
-	mutex_unlock(&driver_lock);
 	return retval;
 }
 
@@ -544,16 +563,9 @@ static int display_open(struct inode *inode, struct file *file)
  */
 static int display_close(struct inode *inode, struct file *file)
 {
-	struct imon_context *ictx = NULL;
+	struct imon_context *ictx = file->private_data;
 	int retval = 0;
 
-	ictx = file->private_data;
-
-	if (!ictx) {
-		pr_err("no context for device\n");
-		return -ENODEV;
-	}
-
 	mutex_lock(&ictx->lock);
 
 	if (!ictx->display_supported) {
@@ -568,6 +580,8 @@ static int display_close(struct inode *inode, struct file *file)
 	}
 
 	mutex_unlock(&ictx->lock);
+	if (refcount_dec_and_test(&ictx->users))
+		free_imon_context(ictx);
 	return retval;
 }
 
@@ -934,15 +948,12 @@ static ssize_t vfd_write(struct file *file, const char __user *buf,
 	int offset;
 	int seq;
 	int retval = 0;
-	struct imon_context *ictx;
+	struct imon_context *ictx = file->private_data;
 	static const unsigned char vfd_packet6[] = {
 		0x01, 0x00, 0x00, 0x00, 0x00, 0xFF, 0xFF };
 
-	ictx = file->private_data;
-	if (!ictx) {
-		pr_err_ratelimited("no context for device\n");
+	if (ictx->disconnected)
 		return -ENODEV;
-	}
 
 	mutex_lock(&ictx->lock);
 
@@ -1018,13 +1029,10 @@ static ssize_t lcd_write(struct file *file, const char __user *buf,
 			 size_t n_bytes, loff_t *pos)
 {
 	int retval = 0;
-	struct imon_context *ictx;
+	struct imon_context *ictx = file->private_data;
 
-	ictx = file->private_data;
-	if (!ictx) {
-		pr_err_ratelimited("no context for device\n");
+	if (ictx->disconnected)
 		return -ENODEV;
-	}
 
 	mutex_lock(&ictx->lock);
 
@@ -2404,7 +2412,6 @@ static int imon_probe(struct usb_interface *interface,
 	int ifnum, sysfs_err;
 	int ret = 0;
 	struct imon_context *ictx = NULL;
-	struct imon_context *first_if_ctx = NULL;
 	u16 vendor, product;
 
 	usbdev     = usb_get_dev(interface_to_usbdev(interface));
@@ -2416,17 +2423,12 @@ static int imon_probe(struct usb_interface *interface,
 	dev_dbg(dev, "%s: found iMON device (%04x:%04x, intf%d)\n",
 		__func__, vendor, product, ifnum);
 
-	/* prevent races probing devices w/multiple interfaces */
-	mutex_lock(&driver_lock);
-
 	first_if = usb_ifnum_to_if(usbdev, 0);
 	if (!first_if) {
 		ret = -ENODEV;
 		goto fail;
 	}
 
-	first_if_ctx = usb_get_intfdata(first_if);
-
 	if (ifnum == 0) {
 		ictx = imon_init_intf0(interface, id);
 		if (!ictx) {
@@ -2434,9 +2436,11 @@ static int imon_probe(struct usb_interface *interface,
 			ret = -ENODEV;
 			goto fail;
 		}
+		refcount_set(&ictx->users, 1);
 
 	} else {
 		/* this is the secondary interface on the device */
+		struct imon_context *first_if_ctx = usb_get_intfdata(first_if);
 
 		/* fail early if first intf failed to register */
 		if (!first_if_ctx) {
@@ -2450,14 +2454,13 @@ static int imon_probe(struct usb_interface *interface,
 			ret = -ENODEV;
 			goto fail;
 		}
+		refcount_inc(&ictx->users);
 
 	}
 
 	usb_set_intfdata(interface, ictx);
 
 	if (ifnum == 0) {
-		mutex_lock(&ictx->lock);
-
 		if (product == 0xffdc && ictx->rf_device) {
 			sysfs_err = sysfs_create_group(&interface->dev.kobj,
 						       &imon_rf_attr_group);
@@ -2468,21 +2471,17 @@ static int imon_probe(struct usb_interface *interface,
 
 		if (ictx->display_supported)
 			imon_init_display(ictx, interface);
-
-		mutex_unlock(&ictx->lock);
 	}
 
 	dev_info(dev, "iMON device (%04x:%04x, intf%d) on usb<%d:%d> initialized\n",
 		 vendor, product, ifnum,
 		 usbdev->bus->busnum, usbdev->devnum);
 
-	mutex_unlock(&driver_lock);
 	usb_put_dev(usbdev);
 
 	return 0;
 
 fail:
-	mutex_unlock(&driver_lock);
 	usb_put_dev(usbdev);
 	dev_err(dev, "unable to register, err %d\n", ret);
 
@@ -2498,10 +2497,8 @@ static void imon_disconnect(struct usb_interface *interface)
 	struct device *dev;
 	int ifnum;
 
-	/* prevent races with multi-interface device probing and display_open */
-	mutex_lock(&driver_lock);
-
 	ictx = usb_get_intfdata(interface);
+	ictx->disconnected = true;
 	dev = ictx->dev;
 	ifnum = interface->cur_altsetting->desc.bInterfaceNumber;
 
@@ -2542,11 +2539,9 @@ static void imon_disconnect(struct usb_interface *interface)
 		}
 	}
 
-	if (!ictx->dev_present_intf0 && !ictx->dev_present_intf1)
+	if (refcount_dec_and_test(&ictx->users))
 		free_imon_context(ictx);
 
-	mutex_unlock(&driver_lock);
-
 	dev_dbg(dev, "%s: iMON device (intf%d) disconnected\n",
 		__func__, ifnum);
 }
Signature · 1 line
2.35.1
author maintainer
#100 lore raw

PATCH 98/135 media: cec-adap.c: fix is_configuring state

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit 59267fc34f4900dcd2ec3295f6be04b79aee2186 ]

If an adapter is trying to claim a free logical address then it is in the 'is_configuring' state. If during that process the cable is disconnected (HPD goes low, which in turn invalidates the physical address), then cec_adap_unconfigure() is called, and that set the is_configuring boolean to false, even though the thread that's trying to claim an LA is still running.

Don't touch the is_configuring bool in cec_adap_unconfigure(), it will eventually be cleared by the thread. By making that change the cec_config_log_addr() function also had to change: it was aborting if is_configuring became false (since that is what cec_adap_unconfigure() did), but that no longer works. Instead check if the physical address is invalid. That is a much more appropriate check anyway.

This fixes a bug where the the adapter could be disabled even though the device was still configuring. This could cause POLL transmits to time out.

---
 drivers/media/cec/core/cec-adap.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/media/cec/core/cec-adap.c +3 -3
index 2e12331c12a9..01766e744772 100644
@@ -1278,7 +1278,7 @@ static int cec_config_log_addr(struct cec_adapter *adap,
 		 * While trying to poll the physical address was reset
 		 * and the adapter was unconfigured, so bail out.
 		 */
-		if (!adap->is_configuring)
+		if (adap->phys_addr == CEC_PHYS_ADDR_INVALID)
 			return -EINTR;
 
 		if (err)
@@ -1335,7 +1335,6 @@ static void cec_adap_unconfigure(struct cec_adapter *adap)
 	    adap->phys_addr != CEC_PHYS_ADDR_INVALID)
 		WARN_ON(adap->ops->adap_log_addr(adap, CEC_LOG_ADDR_INVALID));
 	adap->log_addrs.log_addr_mask = 0;
-	adap->is_configuring = false;
 	adap->is_configured = false;
 	cec_flush(adap);
 	wake_up_interruptible(&adap->kthread_waitq);
@@ -1527,9 +1526,10 @@ static int cec_config_thread_func(void *arg)
 	for (i = 0; i < las->num_log_addrs; i++)
 		las->log_addr[i] = CEC_LOG_ADDR_INVALID;
 	cec_adap_unconfigure(adap);
+	adap->is_configuring = false;
 	adap->kthread_config = NULL;
-	mutex_unlock(&adap->lock);
 	complete(&adap->config_completion);
+	mutex_unlock(&adap->lock);
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#101 lore raw

PATCH 99/135 usbnet: Run unregister_netdev() before unbind() again

In reply to Sasha Levin

From: Lukas Wunner <[email protected]>

[ Upstream commit d1408f6b4dd78fb1b9e26bcf64477984e5f85409 ]

Commit 2c9d6c2b871d ("usbnet: run unbind() before unregister_netdev()") sought to fix a use-after-free on disconnect of USB Ethernet adapters.

It turns out that a different fix is necessary to address the issue:
https://lore.kernel.org/netdev/18b3541e5372bc9b9fc733d422f4e698c089077c.1650177997.git.lukas@wunner.de/

So the commit was not necessary.

The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then register_netdev(). usbnet_disconnect() mirrored that by first invoking unregister_netdev() and then ->unbind().

Since the commit, the order in usbnet_disconnect() is reversed and no longer mirrors usbnet_probe().

One consequence is that a PHY disconnected (and stopped) in ->unbind() is afterwards stopped once more by unregister_netdev() as it closes the netdev before unregistering. That necessitates a contortion in ->stop() because the PHY may only be stopped if it hasn't already been disconnected.

Reverting the commit allows making the call to phy_stop() unconditional in ->stop().

---
 drivers/net/usb/asix_devices.c | 6 +-----
 drivers/net/usb/smsc95xx.c     | 3 +--
 drivers/net/usb/usbnet.c       | 6 +++---
 3 files changed, 5 insertions(+), 10 deletions(-)
drivers/net/usb/asix_devices.c +1 -5
index 6b2fbdf4e0fd..34854ee537dc 100644
@@ -799,11 +799,7 @@ static int ax88772_stop(struct usbnet *dev)
 {
 	struct asix_common_private *priv = dev->driver_priv;
 
-	/* On unplugged USB, we will get MDIO communication errors and the
-	 * PHY will be set in to PHY_HALTED state.
-	 */
-	if (priv->phydev->state != PHY_HALTED)
-		phy_stop(priv->phydev);
+	phy_stop(priv->phydev);
 
 	return 0;
 }
drivers/net/usb/smsc95xx.c +1 -2
index a0f29482294d..d81485cd7e90 100644
@@ -1218,8 +1218,7 @@ static int smsc95xx_start_phy(struct usbnet *dev)
 
 static int smsc95xx_stop(struct usbnet *dev)
 {
-	if (dev->net->phydev)
-		phy_stop(dev->net->phydev);
+	phy_stop(dev->net->phydev);
 
 	return 0;
 }
drivers/net/usb/usbnet.c +3 -3
index 9a6450f796dc..36b24ec11650 100644
@@ -1616,9 +1616,6 @@ void usbnet_disconnect (struct usb_interface *intf)
 		   xdev->bus->bus_name, xdev->devpath,
 		   dev->driver_info->description);
 
-	if (dev->driver_info->unbind)
-		dev->driver_info->unbind(dev, intf);
-
 	net = dev->net;
 	unregister_netdev (net);
 
@@ -1626,6 +1623,9 @@ void usbnet_disconnect (struct usb_interface *intf)
 
 	usb_scuttle_anchored_urbs(&dev->deferred);
 
+	if (dev->driver_info->unbind)
+		dev->driver_info->unbind(dev, intf);
+
 	usb_kill_urb(dev->interrupt);
 	usb_free_urb(dev->interrupt);
 	kfree(dev->padding_pkt);
Signature · 1 line
2.35.1
author maintainer
#102 lore raw

PATCH 100/135 Bluetooth: HCI: Add HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk

In reply to Sasha Levin

From: Luiz Augusto von Dentz <[email protected]>

[ Upstream commit 05abad857277dda198063017b00ba5b9fed2c0cb ]

This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even if its support command bit are set since some controller report it as supported but the command don't work properly with some configurations (e.g. BT_VOICE_TRANSPARENT/mSBC).

---
 include/net/bluetooth/hci.h      | 9 +++++++++
 include/net/bluetooth/hci_core.h | 8 ++++++--
 net/bluetooth/hci_conn.c         | 2 +-
 net/bluetooth/sco.c              | 2 +-
 4 files changed, 17 insertions(+), 4 deletions(-)
include/net/bluetooth/hci.h +9 -0
index 69ef31cea582..62a9bb022aed 100644
@@ -265,6 +265,15 @@ enum {
 	 * runtime suspend, because event filtering takes place there.
 	 */
 	HCI_QUIRK_BROKEN_FILTER_CLEAR_ALL,
+
+	/*
+	 * When this quirk is set, disables the use of
+	 * HCI_OP_ENHANCED_SETUP_SYNC_CONN command to setup SCO connections.
+	 *
+	 * This quirk can be set before hci_register_dev is called or
+	 * during the hdev->setup vendor callback.
+	 */
+	HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN,
 };
 
 /* HCI device flags */
include/net/bluetooth/hci_core.h +6 -2
index 131514913430..49a88b2f4678 100644
@@ -1483,8 +1483,12 @@ void hci_conn_del_sysfs(struct hci_conn *conn);
 #define privacy_mode_capable(dev) (use_ll_privacy(dev) && \
 				   (hdev->commands[39] & 0x04))
 
-/* Use enhanced synchronous connection if command is supported */
-#define enhanced_sco_capable(dev) ((dev)->commands[29] & 0x08)
+/* Use enhanced synchronous connection if command is supported and its quirk
+ * has not been set.
+ */
+#define enhanced_sync_conn_capable(dev) \
+	(((dev)->commands[29] & 0x08) && \
+	 !test_bit(HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN, &(dev)->quirks))
 
 /* Use ext scanning if set ext scan param and ext scan enable is supported */
 #define use_ext_scan(dev) (((dev)->commands[37] & 0x20) && \
net/bluetooth/hci_conn.c +1 -1
index 84312c836549..cd51bf2a709b 100644
@@ -481,7 +481,7 @@ static bool hci_setup_sync_conn(struct hci_conn *conn, __u16 handle)
 
 bool hci_setup_sync(struct hci_conn *conn, __u16 handle)
 {
-	if (enhanced_sco_capable(conn->hdev))
+	if (enhanced_sync_conn_capable(conn->hdev))
 		return hci_enhanced_setup_sync_conn(conn, handle);
 
 	return hci_setup_sync_conn(conn, handle);
net/bluetooth/sco.c +1 -1
index 8eabf41b2993..2a58c7d88433 100644
@@ -885,7 +885,7 @@ static int sco_sock_setsockopt(struct socket *sock, int level, int optname,
 			err = -EBADFD;
 			break;
 		}
-		if (enhanced_sco_capable(hdev) &&
+		if (enhanced_sync_conn_capable(hdev) &&
 		    voice.setting == BT_VOICE_TRANSPARENT)
 			sco_pi(sk)->codec.id = BT_CODEC_TRANSPARENT;
 		hci_dev_put(hdev);
Signature · 1 line
2.35.1
author maintainer
#103 lore raw

PATCH 101/135 Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA

In reply to Sasha Levin

From: Luiz Augusto von Dentz <[email protected]>

[ Upstream commit d44e1dbda36fff5d7c2586683c4adc0963aef908 ]

This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA controllers since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.

---
 drivers/bluetooth/btusb.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/bluetooth/btusb.c +5 -0
index 42234d5f602d..34215dc5e684 100644
@@ -3317,6 +3317,11 @@ static int btusb_setup_qca(struct hci_dev *hdev)
 			return err;
 	}
 
+	/* Mark HCI_OP_ENHANCED_SETUP_SYNC_CONN as broken as it doesn't seem to
+	 * work with the likes of HSP/HFP mSBC.
+	 */
+	set_bit(HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN, &hdev->quirks);
+
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#104 lore raw

PATCH 102/135 Bluetooth: btusb: Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA

In reply to Sasha Levin

From: Zijun Hu <[email protected]>

[ Upstream commit 247f226adadfb7be09dd537f177429f4415aef8e ]

Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA controllers since they answer HCI_OP_READ_DEF_ERR_DATA_REPORTING with error code "UNKNOWN HCI COMMAND" as shown below:

[  580.517552] Bluetooth: hci0: unexpected cc 0x0c5a length: 1 < 2
[  580.517660] Bluetooth: hci0: Opcode 0x c5a failed: -38

hcitool -i hci0 cmd 0x03 0x5a
< HCI Command: ogf 0x03, ocf 0x005a, plen 0

Quoted 1 line

HCI Event: 0x0e plen 4

01 5A 0C 01

btmon log:
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0

Quoted 1 line

HCI Event: Command Complete (0x0e) plen 4

      Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
        Status: Unknown HCI Command (0x01)
---
 drivers/bluetooth/btusb.c | 1 +
 1 file changed, 1 insertion(+)
drivers/bluetooth/btusb.c +1 -0
index 34215dc5e684..304351d2cfdf 100644
@@ -3321,6 +3321,7 @@ static int btusb_setup_qca(struct hci_dev *hdev)
 	 * work with the likes of HSP/HFP mSBC.
 	 */
 	set_bit(HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN, &hdev->quirks);
+	set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);
 
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#105 lore raw

PATCH 103/135 init: call time_init() before rand_initialize()

In reply to Sasha Levin

From: "Jason A. Donenfeld" <[email protected]>

[ Upstream commit fe222a6ca2d53c38433cba5d3be62a39099e708e ]

Currently time_init() is called after rand_initialize(), but rand_initialize() makes use of the timer on various platforms, and sometimes this timer needs to be initialized by time_init() first. In order for random_get_entropy() to not return zero during early boot when it's potentially used as an entropy source, reverse the order of these two calls. The block doing random initialization was right before time_init() before, so changing the order shouldn't have any complicated effects.

---
 init/main.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
init/main.c +2 -1
index 9a5097b2251a..b18aa5d19038 100644
@@ -1035,11 +1035,13 @@ asmlinkage __visible void __init __no_sanitize_address start_kernel(void)
 	softirq_init();
 	timekeeping_init();
 	kfence_init();
+	time_init();
 
 	/*
 	 * For best initial stack canary entropy, prepare it after:
 	 * - setup_arch() for any UEFI RNG entropy and boot cmdline access
 	 * - timekeeping_init() for ktime entropy used in rand_initialize()
+	 * - time_init() for making random_get_entropy() work on some platforms
 	 * - rand_initialize() to get any arch-specific entropy like RDRAND
 	 * - add_latent_entropy() to get any latent entropy
 	 * - adding command line entropy
@@ -1049,7 +1051,6 @@ asmlinkage __visible void __init __no_sanitize_address start_kernel(void)
 	add_device_randomness(command_line, strlen(command_line));
 	boot_init_stack_canary();
 
-	time_init();
 	perf_event_init();
 	profile_init();
 	call_function_init();
Signature · 1 line
2.35.1
author maintainer
#106 lore raw

PATCH 104/135 openrisc: start CPU timer early in boot

In reply to Sasha Levin

From: "Jason A. Donenfeld" <[email protected]>

[ Upstream commit 516dd4aacd67a0f27da94f3fe63fe0f4dbab6e2b ]

In order to measure the boot process, the timer should be switched on as early in boot as possible. As well, the commit defines the get_cycles macro, like the previous patches in this series, so that generic code is aware that it's implemented by the platform, as is done on other archs.

---
 arch/openrisc/include/asm/timex.h | 1 +
 arch/openrisc/kernel/head.S       | 9 +++++++++
 2 files changed, 10 insertions(+)
arch/openrisc/include/asm/timex.h +1 -0
index d52b4e536e3f..5487fa93dd9b 100644
@@ -23,6 +23,7 @@ static inline cycles_t get_cycles(void)
 {
 	return mfspr(SPR_TTCR);
 }
+#define get_cycles get_cycles
 
 /* This isn't really used any more */
 #define CLOCK_TICK_RATE 1000
arch/openrisc/kernel/head.S +9 -0
index 15f1b38dfe03..871f4c858859 100644
@@ -521,6 +521,15 @@ _start:
 	l.ori	r3,r0,0x1
 	l.mtspr	r0,r3,SPR_SR
 
+	/*
+	 * Start the TTCR as early as possible, so that the RNG can make use of
+	 * measurements of boot time from the earliest opportunity. Especially
+	 * important is that the TTCR does not return zero by the time we reach
+	 * rand_initialize().
+	 */
+	l.movhi r3,hi(SPR_TTMR_CR)
+	l.mtspr r0,r3,SPR_TTMR
+
 	CLEAR_GPR(r1)
 	CLEAR_GPR(r2)
 	CLEAR_GPR(r3)
Signature · 1 line
2.35.1
author maintainer
#107 lore raw

PATCH 105/135 nvme-pci: fix a NULL pointer dereference in nvme_alloc_admin_tags

In reply to Sasha Levin

From: "Smith, Kyle Miller (Nimble Kernel)" <[email protected]>

[ Upstream commit da42761181627e9bdc37d18368b827948a583929 ]

In nvme_alloc_admin_tags, the admin_q can be set to an error (typically -ENOMEM) if the blk_mq_init_queue call fails to set up the queue, which is checked immediately after the call. However, when we return the error message up the stack, to nvme_reset_work the error takes us to nvme_remove_dead_ctrl()
nvme_dev_disable()
nvme_suspend_queue(&dev->queues[0]).

Here, we only check that the admin_q is non-NULL, rather than not an error or NULL, and begin quiescing a queue that never existed, leading to bad / NULL pointer dereference.

---
 drivers/nvme/host/pci.c | 1 +
 1 file changed, 1 insertion(+)
drivers/nvme/host/pci.c +1 -0
index 94a0b933b133..823fa48fbfb0 100644
@@ -1772,6 +1772,7 @@ static int nvme_alloc_admin_tags(struct nvme_dev *dev)
 		dev->ctrl.admin_q = blk_mq_init_queue(&dev->admin_tagset);
 		if (IS_ERR(dev->ctrl.admin_q)) {
 			blk_mq_free_tag_set(&dev->admin_tagset);
+			dev->ctrl.admin_q = NULL;
 			return -ENOMEM;
 		}
 		if (!blk_get_queue(dev->ctrl.admin_q)) {
Signature · 1 line
2.35.1
author maintainer
#108 lore raw

PATCH 106/135 ASoC: rt5645: Fix errorenous cleanup order

In reply to Sasha Levin

From: Lin Ma <[email protected]>

[ Upstream commit 2def44d3aec59e38d2701c568d65540783f90f2f ]

There is a logic error when removing rt5645 device as the function rt5645_i2c_remove() first cancel the &rt5645->jack_detect_work and delete the &rt5645->btn_check_timer latter. However, since the timer handler rt5645_btn_check_callback() will re-queue the jack_detect_work, this cleanup order is buggy.

That is, once the del_timer_sync in rt5645_i2c_remove is concurrently run with the rt5645_btn_check_callback, the canceled jack_detect_work will be rescheduled again, leading to possible use-after-free.

This patch fix the issue by placing the del_timer_sync function before the cancel_delayed_work_sync.

---
 sound/soc/codecs/rt5645.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
sound/soc/codecs/rt5645.c +6 -1
index 197c56047947..4b2e027c1033 100644
@@ -4154,9 +4154,14 @@ static int rt5645_i2c_remove(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, rt5645);
 
+	/*
+	 * Since the rt5645_btn_check_callback() can queue jack_detect_work,
+	 * the timer need to be delted first
+	 */
+	del_timer_sync(&rt5645->btn_check_timer);
+
 	cancel_delayed_work_sync(&rt5645->jack_detect_work);
 	cancel_delayed_work_sync(&rt5645->rcclock_work);
-	del_timer_sync(&rt5645->btn_check_timer);
 
 	regulator_bulk_disable(ARRAY_SIZE(rt5645->supplies), rt5645->supplies);
 
Signature · 1 line
2.35.1
author maintainer
#109 lore raw

PATCH 107/135 nbd: Fix hung on disconnect request if socket is closed before

In reply to Sasha Levin

From: Xie Yongji <[email protected]>

[ Upstream commit 491bf8f236fdeec698fa6744993f1ecf3fafd1a5 ]

When userspace closes the socket before sending a disconnect request, the following I/O requests will be blocked in wait_for_reconnect() until dead timeout. This will cause the following disconnect request also hung on blk_mq_quiesce_queue(). That means we have no way to disconnect a nbd device if there are some I/O requests waiting for reconnecting until dead timeout. It's not expected. So let's wake up the thread waiting for reconnecting directly when a disconnect request is sent.

---
 drivers/block/nbd.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/block/nbd.c +9 -4
index 5a1f98494ddd..284557041336 100644
@@ -947,11 +947,15 @@ static int wait_for_reconnect(struct nbd_device *nbd)
 	struct nbd_config *config = nbd->config;
 	if (!config->dead_conn_timeout)
 		return 0;
-	if (test_bit(NBD_RT_DISCONNECTED, &config->runtime_flags))
+
+	if (!wait_event_timeout(config->conn_wait,
+				test_bit(NBD_RT_DISCONNECTED,
+					 &config->runtime_flags) ||
+				atomic_read(&config->live_connections) > 0,
+				config->dead_conn_timeout))
 		return 0;
-	return wait_event_timeout(config->conn_wait,
-				  atomic_read(&config->live_connections) > 0,
-				  config->dead_conn_timeout) > 0;
+
+	return !test_bit(NBD_RT_DISCONNECTED, &config->runtime_flags);
 }
 
 static int nbd_handle_cmd(struct nbd_cmd *cmd, int index)
@@ -2082,6 +2086,7 @@ static void nbd_disconnect_and_put(struct nbd_device *nbd)
 	mutex_lock(&nbd->config_lock);
 	nbd_disconnect(nbd);
 	sock_shutdown(nbd);
+	wake_up(&nbd->config->conn_wait);
 	/*
 	 * Make sure recv thread has finished, we can safely call nbd_clear_que()
 	 * to cancel the inflight I/Os.
Signature · 1 line
2.35.1
author maintainer
#110 lore raw

PATCH 108/135 drm/amd/pm: update smartshift powerboost calc for smu12

In reply to Sasha Levin

From: Sathishkumar S <[email protected]>

[ Upstream commit 138292f1dc00e7e0724f44769f9da39cf2f3bf0b ]

smartshift apu and dgpu power boost are reported as percentage with respect to their power limits. This value[0-100] reflects the boost for the respective device.

---
 .../gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c   | 60 ++++++++++++++-----
 1 file changed, 44 insertions(+), 16 deletions(-)
drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c +44 -16
index 25c4b135f830..5e7c9e6d8125 100644
@@ -1119,6 +1119,39 @@ static int renoir_get_power_profile_mode(struct smu_context *smu,
 	return size;
 }
 
+static void renoir_get_ss_power_percent(SmuMetrics_t *metrics,
+					uint32_t *apu_percent, uint32_t *dgpu_percent)
+{
+	uint32_t apu_boost = 0;
+	uint32_t dgpu_boost = 0;
+	uint16_t apu_limit = 0;
+	uint16_t dgpu_limit = 0;
+	uint16_t apu_power = 0;
+	uint16_t dgpu_power = 0;
+
+	apu_power = metrics->ApuPower;
+	apu_limit = metrics->StapmOriginalLimit;
+	if (apu_power > apu_limit && apu_limit != 0)
+		apu_boost =  ((apu_power - apu_limit) * 100) / apu_limit;
+	apu_boost = (apu_boost > 100) ? 100 : apu_boost;
+
+	dgpu_power = metrics->dGpuPower;
+	if (metrics->StapmCurrentLimit > metrics->StapmOriginalLimit)
+		dgpu_limit = metrics->StapmCurrentLimit - metrics->StapmOriginalLimit;
+	if (dgpu_power > dgpu_limit && dgpu_limit != 0)
+		dgpu_boost = ((dgpu_power - dgpu_limit) * 100) / dgpu_limit;
+	dgpu_boost = (dgpu_boost > 100) ? 100 : dgpu_boost;
+
+	if (dgpu_boost >= apu_boost)
+		apu_boost = 0;
+	else
+		dgpu_boost = 0;
+
+	*apu_percent = apu_boost;
+	*dgpu_percent = dgpu_boost;
+}
+
+
 static int renoir_get_smu_metrics_data(struct smu_context *smu,
 				       MetricsMember_t member,
 				       uint32_t *value)
@@ -1127,6 +1160,9 @@ static int renoir_get_smu_metrics_data(struct smu_context *smu,
 
 	SmuMetrics_t *metrics = (SmuMetrics_t *)smu_table->metrics_table;
 	int ret = 0;
+	uint32_t apu_percent = 0;
+	uint32_t dgpu_percent = 0;
+
 
 	mutex_lock(&smu->metrics_lock);
 
@@ -1175,26 +1211,18 @@ static int renoir_get_smu_metrics_data(struct smu_context *smu,
 		*value = metrics->Voltage[1];
 		break;
 	case METRICS_SS_APU_SHARE:
-		/* return the percentage of APU power with respect to APU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of APU power boost
+		 * with respect to APU's power limit.
 		 */
-		if (metrics->StapmOriginalLimit > 0)
-			*value =  (metrics->ApuPower * 100) / metrics->StapmOriginalLimit;
-		else
-			*value = 0;
+		renoir_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = apu_percent;
 		break;
 	case METRICS_SS_DGPU_SHARE:
-		/* return the percentage of dGPU power with respect to dGPU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of dGPU power boost
+		 * with respect to dGPU's power limit.
 		 */
-		if ((metrics->dGpuPower > 0) &&
-		    (metrics->StapmCurrentLimit > metrics->StapmOriginalLimit))
-			*value = (metrics->dGpuPower * 100) /
-				  (metrics->StapmCurrentLimit - metrics->StapmOriginalLimit);
-		else
-			*value = 0;
+		renoir_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = dgpu_percent;
 		break;
 	default:
 		*value = UINT_MAX;
Signature · 1 line
2.35.1
author maintainer
#111 lore raw

PATCH 109/135 drm/amd/pm: update smartshift powerboost calc for smu13

In reply to Sasha Levin

From: Sathishkumar S <[email protected]>

[ Upstream commit cdf4c8ec39872a61a58d62f19b4db80f0f7bc586 ]

smartshift apu and dgpu power boost are reported as percentage with respect to their power limits. adjust the units of power before calculating the percentage of boost.

---
 .../drm/amd/pm/swsmu/smu13/yellow_carp_ppt.c  | 62 ++++++++++++++-----
 1 file changed, 46 insertions(+), 16 deletions(-)
drivers/gpu/drm/amd/pm/swsmu/smu13/yellow_carp_ppt.c +46 -16
index 0bc84b709a93..d0715927b07f 100644
@@ -296,6 +296,42 @@ static int yellow_carp_mode2_reset(struct smu_context *smu)
 	return yellow_carp_mode_reset(smu, SMU_RESET_MODE_2);
 }
 
+
+static void yellow_carp_get_ss_power_percent(SmuMetrics_t *metrics,
+					uint32_t *apu_percent, uint32_t *dgpu_percent)
+{
+	uint32_t apu_boost = 0;
+	uint32_t dgpu_boost = 0;
+	uint16_t apu_limit = 0;
+	uint16_t dgpu_limit = 0;
+	uint16_t apu_power = 0;
+	uint16_t dgpu_power = 0;
+
+	/* APU and dGPU power values are reported in milli Watts
+	 * and STAPM power limits are in Watts */
+	apu_power = metrics->ApuPower/1000;
+	apu_limit = metrics->StapmOpnLimit;
+	if (apu_power > apu_limit && apu_limit != 0)
+		apu_boost =  ((apu_power - apu_limit) * 100) / apu_limit;
+	apu_boost = (apu_boost > 100) ? 100 : apu_boost;
+
+	dgpu_power = metrics->dGpuPower/1000;
+	if (metrics->StapmCurrentLimit > metrics->StapmOpnLimit)
+		dgpu_limit = metrics->StapmCurrentLimit - metrics->StapmOpnLimit;
+	if (dgpu_power > dgpu_limit && dgpu_limit != 0)
+		dgpu_boost = ((dgpu_power - dgpu_limit) * 100) / dgpu_limit;
+	dgpu_boost = (dgpu_boost > 100) ? 100 : dgpu_boost;
+
+	if (dgpu_boost >= apu_boost)
+		apu_boost = 0;
+	else
+		dgpu_boost = 0;
+
+	*apu_percent = apu_boost;
+	*dgpu_percent = dgpu_boost;
+
+}
+
 static int yellow_carp_get_smu_metrics_data(struct smu_context *smu,
 							MetricsMember_t member,
 							uint32_t *value)
@@ -304,6 +340,8 @@ static int yellow_carp_get_smu_metrics_data(struct smu_context *smu,
 
 	SmuMetrics_t *metrics = (SmuMetrics_t *)smu_table->metrics_table;
 	int ret = 0;
+	uint32_t apu_percent = 0;
+	uint32_t dgpu_percent = 0;
 
 	mutex_lock(&smu->metrics_lock);
 
@@ -356,26 +394,18 @@ static int yellow_carp_get_smu_metrics_data(struct smu_context *smu,
 		*value = metrics->Voltage[1];
 		break;
 	case METRICS_SS_APU_SHARE:
-		/* return the percentage of APU power with respect to APU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of APU power boost
+		 * with respect to APU's power limit.
 		 */
-		if (metrics->StapmOpnLimit > 0)
-			*value =  (metrics->ApuPower * 100) / metrics->StapmOpnLimit;
-		else
-			*value = 0;
+		yellow_carp_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = apu_percent;
 		break;
 	case METRICS_SS_DGPU_SHARE:
-		/* return the percentage of dGPU power with respect to dGPU's power limit.
-		 * percentage is reported, this isn't boost value. Smartshift power
-		 * boost/shift is only when the percentage is more than 100.
+		/* return the percentage of dGPU power boost
+		 * with respect to dGPU's power limit.
 		 */
-		if ((metrics->dGpuPower > 0) &&
-		    (metrics->StapmCurrentLimit > metrics->StapmOpnLimit))
-			*value = (metrics->dGpuPower * 100) /
-				  (metrics->StapmCurrentLimit - metrics->StapmOpnLimit);
-		else
-			*value = 0;
+		yellow_carp_get_ss_power_percent(metrics, &apu_percent, &dgpu_percent);
+		*value = dgpu_percent;
 		break;
 	default:
 		*value = UINT_MAX;
Signature · 1 line
2.35.1
author maintainer
#112 lore raw

PATCH 110/135 btrfs: fix anon_dev leak in create_subvol()

In reply to Sasha Levin

From: Omar Sandoval <[email protected]>

[ Upstream commit 2256e901f5bddc56e24089c96f27b77da932dfcc ]

When btrfs_qgroup_inherit(), btrfs_alloc_tree_block, or btrfs_insert_root() fail in create_subvol(), we return without freeing anon_dev. Reorganize the error handling in create_subvol() to fix this.

---
 fs/btrfs/ioctl.c | 49 +++++++++++++++++++++++-------------------------
 1 file changed, 23 insertions(+), 26 deletions(-)
fs/btrfs/ioctl.c +23 -26
index 8fe9d55d6862..072cdcab3061 100644
@@ -544,7 +544,7 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	struct timespec64 cur_time = current_time(dir);
 	struct inode *inode;
 	int ret;
-	dev_t anon_dev = 0;
+	dev_t anon_dev;
 	u64 objectid;
 	u64 index = 0;
 
@@ -554,11 +554,7 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 
 	ret = btrfs_get_free_objectid(fs_info->tree_root, &objectid);
 	if (ret)
-		goto fail_free;
-
-	ret = get_anon_bdev(&anon_dev);
-	if (ret < 0)
-		goto fail_free;
+		goto out_root_item;
 
 	/*
 	 * Don't create subvolume whose level is not zero. Or qgroup will be
@@ -566,9 +562,13 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	 */
 	if (btrfs_qgroup_level(objectid)) {
 		ret = -ENOSPC;
-		goto fail_free;
+		goto out_root_item;
 	}
 
+	ret = get_anon_bdev(&anon_dev);
+	if (ret < 0)
+		goto out_root_item;
+
 	btrfs_init_block_rsv(&block_rsv, BTRFS_BLOCK_RSV_TEMP);
 	/*
 	 * The same as the snapshot creation, please see the comment
@@ -576,26 +576,26 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	 */
 	ret = btrfs_subvolume_reserve_metadata(root, &block_rsv, 8, false);
 	if (ret)
-		goto fail_free;
+		goto out_anon_dev;
 
 	trans = btrfs_start_transaction(root, 0);
 	if (IS_ERR(trans)) {
 		ret = PTR_ERR(trans);
 		btrfs_subvolume_release_metadata(root, &block_rsv);
-		goto fail_free;
+		goto out_anon_dev;
 	}
 	trans->block_rsv = &block_rsv;
 	trans->bytes_reserved = block_rsv.size;
 
 	ret = btrfs_qgroup_inherit(trans, 0, objectid, inherit);
 	if (ret)
-		goto fail;
+		goto out;
 
 	leaf = btrfs_alloc_tree_block(trans, root, 0, objectid, NULL, 0, 0, 0,
 				      BTRFS_NESTING_NORMAL);
 	if (IS_ERR(leaf)) {
 		ret = PTR_ERR(leaf);
-		goto fail;
+		goto out;
 	}
 
 	btrfs_mark_buffer_dirty(leaf);
@@ -650,7 +650,7 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 		btrfs_tree_unlock(leaf);
 		btrfs_free_tree_block(trans, objectid, leaf, 0, 1);
 		free_extent_buffer(leaf);
-		goto fail;
+		goto out;
 	}
 
 	free_extent_buffer(leaf);
@@ -659,19 +659,18 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	key.offset = (u64)-1;
 	new_root = btrfs_get_new_fs_root(fs_info, objectid, anon_dev);
 	if (IS_ERR(new_root)) {
-		free_anon_bdev(anon_dev);
 		ret = PTR_ERR(new_root);
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
-	/* Freeing will be done in btrfs_put_root() of new_root */
+	/* anon_dev is owned by new_root now. */
 	anon_dev = 0;
 
 	ret = btrfs_record_root_in_trans(trans, new_root);
 	if (ret) {
 		btrfs_put_root(new_root);
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	ret = btrfs_create_subvol_root(trans, new_root, root, mnt_userns);
@@ -679,7 +678,7 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	if (ret) {
 		/* We potentially lose an unused inode item here */
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	/*
@@ -688,28 +687,28 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	ret = btrfs_set_inode_index(BTRFS_I(dir), &index);
 	if (ret) {
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	ret = btrfs_insert_dir_item(trans, name, namelen, BTRFS_I(dir), &key,
 				    BTRFS_FT_DIR, index);
 	if (ret) {
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	btrfs_i_size_write(BTRFS_I(dir), dir->i_size + namelen * 2);
 	ret = btrfs_update_inode(trans, root, BTRFS_I(dir));
 	if (ret) {
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	ret = btrfs_add_root_ref(trans, objectid, root->root_key.objectid,
 				 btrfs_ino(BTRFS_I(dir)), index, name, namelen);
 	if (ret) {
 		btrfs_abort_transaction(trans, ret);
-		goto fail;
+		goto out;
 	}
 
 	ret = btrfs_uuid_tree_add(trans, root_item->uuid,
@@ -717,8 +716,7 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 	if (ret)
 		btrfs_abort_transaction(trans, ret);
 
-fail:
-	kfree(root_item);
+out:
 	trans->block_rsv = NULL;
 	trans->bytes_reserved = 0;
 	btrfs_subvolume_release_metadata(root, &block_rsv);
@@ -734,11 +732,10 @@ static noinline int create_subvol(struct user_namespace *mnt_userns,
 			return PTR_ERR(inode);
 		d_instantiate(dentry, inode);
 	}
-	return ret;
-
-fail_free:
+out_anon_dev:
 	if (anon_dev)
 		free_anon_bdev(anon_dev);
+out_root_item:
 	kfree(root_item);
 	return ret;
 }
Signature · 1 line
2.35.1
author maintainer
#113 lore raw

PATCH 111/135 kunit: tool: make parser stop overwriting status of suites w/ no_tests

In reply to Sasha Levin

From: Daniel Latypov <[email protected]>

[ Upstream commit dbf0b0d53a2b5afa6ef7372dcedf52302669fc2c ]

Consider this invocation

$ ./tools/testing/kunit/kunit.py parse <<EOF
  TAP version 14
  1..2
  ok 1 - suite
    # Subtest: no_tests_suite
    # catastrophic error!
  not ok 1 - no_tests_suite
EOF

It will have a 0 exit code even though there's a "not ok".

Consider this one:

$ ./tools/testing/kunit/kunit.py parse <<EOF
  TAP version 14
  1..2
  ok 1 - suite
  not ok 1 - no_tests_suite
EOF

It will a non-zero exit code.

Why?
We have this line in the kunit_parser.py

Quoted 1 line

parent_test = parse_test_header(lines, test)

where we have special handling when we see "# Subtest" and we ignore the explicit reported "not ok 1" status!

Also, NO_TESTS at a suite-level only results in a non-zero status code where then there's only one suite atm.

This change is the minimal one to make sure we don't overwrite it.

---
 tools/testing/kunit/kunit_parser.py                        | 7 +++++--
 .../test_data/test_is_test_passed-no_tests_no_plan.log     | 2 +-
 2 files changed, 6 insertions(+), 3 deletions(-)
tools/testing/kunit/kunit_parser.py +5 -2
index 05ff334761dd..2f93ed1d7f99 100644
@@ -789,8 +789,11 @@ def parse_test(lines: LineStream, expected_num: int, log: List[str]) -> Test:
 
 	# Check for there being no tests
 	if parent_test and len(subtests) == 0:
-		test.status = TestStatus.NO_TESTS
-		test.add_error('0 tests run!')
+		# Don't override a bad status if this test had one reported.
+		# Assumption: no subtests means CRASHED is from Test.__init__()
+		if test.status in (TestStatus.TEST_CRASHED, TestStatus.SUCCESS):
+			test.status = TestStatus.NO_TESTS
+			test.add_error('0 tests run!')
 
 	# Add statuses to TestCounts attribute in Test object
 	bubble_up_test_results(test)
tools/testing/kunit/test_data/test_is_test_passed-no_tests_no_plan.log +1 -1
index dd873c981108..4f81876ee6f1 100644
@@ -3,5 +3,5 @@ TAP version 14
   # Subtest: suite
   1..1
     # Subtest: case
-  ok 1 - case # SKIP
+  ok 1 - case
 ok 1 - suite
Signature · 1 line
2.35.1
author maintainer
#114 lore raw

PATCH 112/135 net: phy: micrel: Allow probing without .driver_data

In reply to Sasha Levin

From: Fabio Estevam <[email protected]>

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure and the .driver_data is not, a NULL pointer dereference happens.

Allow passing .probe without .driver_data by inserting NULL checks for priv->type.

---
 drivers/net/phy/micrel.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
drivers/net/phy/micrel.c +6 -5
index cfb5378bbb39..f20d8c3e91bf 100644
@@ -348,7 +348,7 @@ static int kszphy_config_reset(struct phy_device *phydev)
 		}
 	}
 
-	if (priv->led_mode >= 0)
+	if (priv->type && priv->led_mode >= 0)
 		kszphy_setup_led(phydev, priv->type->led_mode_reg, priv->led_mode);
 
 	return 0;
@@ -364,10 +364,10 @@ static int kszphy_config_init(struct phy_device *phydev)
 
 	type = priv->type;
 
-	if (type->has_broadcast_disable)
+	if (type && type->has_broadcast_disable)
 		kszphy_broadcast_disable(phydev);
 
-	if (type->has_nand_tree_disable)
+	if (type && type->has_nand_tree_disable)
 		kszphy_nand_tree_disable(phydev);
 
 	return kszphy_config_reset(phydev);
@@ -1365,7 +1365,7 @@ static int kszphy_probe(struct phy_device *phydev)
 
 	priv->type = type;
 
-	if (type->led_mode_reg) {
+	if (type && type->led_mode_reg) {
 		ret = of_property_read_u32(np, "micrel,led-mode",
 				&priv->led_mode);
 		if (ret)
@@ -1386,7 +1386,8 @@ static int kszphy_probe(struct phy_device *phydev)
 		unsigned long rate = clk_get_rate(clk);
 		bool rmii_ref_clk_sel_25_mhz;
 
-		priv->rmii_ref_clk_sel = type->has_rmii_ref_clk_sel;
+		if (type)
+			priv->rmii_ref_clk_sel = type->has_rmii_ref_clk_sel;
 		rmii_ref_clk_sel_25_mhz = of_property_read_bool(np,
 				"micrel,rmii-reference-clock-select-25-mhz");
 
Signature · 1 line
2.35.1
author maintainer
#115 lore raw

PATCH 113/135 media: exynos4-is: Fix compile warning

In reply to Sasha Levin

From: Kwanghoon Son <[email protected]>

[ Upstream commit e080f5c1f2b6d02c02ee5d674e0e392ccf63bbaf ]

Declare static on function 'fimc_isp_video_device_unregister'.

When VIDEO_EXYNOS4_ISP_DMA_CAPTURE=n, compiler warns about
warning: no previous prototype for function [-Wmissing-prototypes]

---
 drivers/media/platform/exynos4-is/fimc-isp-video.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/platform/exynos4-is/fimc-isp-video.h +1 -1
index edcb3a5e3cb9..2dd4ddbc748a 100644
@@ -32,7 +32,7 @@ static inline int fimc_isp_video_device_register(struct fimc_isp *isp,
 	return 0;
 }
 
-void fimc_isp_video_device_unregister(struct fimc_isp *isp,
+static inline void fimc_isp_video_device_unregister(struct fimc_isp *isp,
 				enum v4l2_buf_type type)
 {
 }
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#116 lore raw

PATCH 114/135 media: hantro: Stop using H.264 parameter pic_num

In reply to Sasha Levin

From: Nicolas Dufresne <[email protected]>

[ Upstream commit 831410700909f4e29d5af1ef26b8c59fc2d1988e ]

The hardware expects FrameNumWrap or long_term_frame_idx. Picture numbers are per field, and are mostly used during the memory management process, which is done in userland. This fixes two ITU conformance tests:

- MR6_BT_B
- MR8_BT_B

---
 drivers/staging/media/hantro/hantro_h264.c | 2 --
 1 file changed, 2 deletions(-)
drivers/staging/media/hantro/hantro_h264.c +0 -2
index 0b4d2491be3b..228629fb3cdf 100644
@@ -354,8 +354,6 @@ u16 hantro_h264_get_ref_nbr(struct hantro_ctx *ctx, unsigned int dpb_idx)
 
 	if (!(dpb->flags & V4L2_H264_DPB_ENTRY_FLAG_ACTIVE))
 		return 0;
-	if (dpb->flags & V4L2_H264_DPB_ENTRY_FLAG_LONG_TERM)
-		return dpb->pic_num;
 	return dpb->frame_num;
 }
 
Signature · 1 line
2.35.1
author maintainer
#117 lore raw

PATCH 115/135 rtw89: cfo: check mac_id to avoid out-of-bounds

In reply to Sasha Levin

From: Ping-Ke Shih <[email protected]>

[ Upstream commit 97df85871a5b187609d30fca6d85b912d9e02f29 ]

Somehow, hardware reports incorrect mac_id and pollute memory. Check index before we access the array.

  UBSAN: array-index-out-of-bounds in rtw89/phy.c:2517:23
  index 188 is out of range for type 's32 [64]'
  CPU: 1 PID: 51550 Comm: irq/35-rtw89_pc Tainted: G           OE
  Call Trace:
   <IRQ>
   show_stack+0x52/0x58
   dump_stack_lvl+0x4c/0x63
   dump_stack+0x10/0x12
   ubsan_epilogue+0x9/0x45
   __ubsan_handle_out_of_bounds.cold+0x44/0x49
   ? __alloc_skb+0x92/0x1d0
   rtw89_phy_cfo_parse+0x44/0x7f [rtw89_core]
   rtw89_core_rx+0x261/0x871 [rtw89_core]
   ? __alloc_skb+0xee/0x1d0
   rtw89_pci_napi_poll+0x3fa/0x4ea [rtw89_pci]
   __napi_poll+0x33/0x1a0
   net_rx_action+0x126/0x260
   ? __queue_work+0x217/0x4c0
   __do_softirq+0xd9/0x315
   ? disable_irq_nosync+0x10/0x10
   do_softirq.part.0+0x6d/0x90
   </IRQ>
   <TASK>
   __local_bh_enable_ip+0x62/0x70
   rtw89_pci_interrupt_threadfn+0x182/0x1a6 [rtw89_pci]
   irq_thread_fn+0x28/0x60
   irq_thread+0xc8/0x190
   ? irq_thread_fn+0x60/0x60
   kthread+0x16b/0x190
   ? irq_thread_check_affinity+0xe0/0xe0
   ? set_kthread_struct+0x50/0x50
   ret_from_fork+0x22/0x30
   </TASK>
---
 drivers/net/wireless/realtek/rtw89/phy.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/net/wireless/realtek/rtw89/phy.c +5 -0
index 147009888de0..777ad4e8f45f 100644
@@ -1872,6 +1872,11 @@ void rtw89_phy_cfo_parse(struct rtw89_dev *rtwdev, s16 cfo_val,
 	struct rtw89_cfo_tracking_info *cfo = &rtwdev->cfo_tracking;
 	u8 macid = phy_ppdu->mac_id;
 
+	if (macid >= CFO_TRACK_MAX_USER) {
+		rtw89_warn(rtwdev, "mac_id %d is out of range\n", macid);
+		return;
+	}
+
 	cfo->cfo_tail[macid] += cfo_val;
 	cfo->cfo_cnt[macid]++;
 	cfo->packet_count++;
Signature · 1 line
2.35.1
author maintainer
#118 lore raw

PATCH 116/135 of/fdt: Ignore disabled memory nodes

In reply to Sasha Levin

From: Andre Przywara <[email protected]>

[ Upstream commit df5cd369876114f91f9ae60658fea80acfb15890 ]

When we boot a machine using a devicetree, the generic DT code goes through all nodes with a 'device_type = "memory"' property, and collects all memory banks mentioned there. However it does not check for the status property, so any nodes which are explicitly "disabled" will still be added as a memblock.
This ends up badly for QEMU, when booting with secure firmware on arm/arm64 machines, because QEMU adds a node describing secure-only memory:
===================

	secram@e000000 {
		secure-status = "okay";
		status = "disabled";
		reg = <0x00 0xe000000 0x00 0x1000000>;
		device_type = "memory";
	};

===================

The kernel will eventually use that memory block (which is located below the main DRAM bank), but accesses to that will be answered with an SError:
===================

[    0.000000] Internal error: synchronous external abort: 96000050 [#1] PREEMPT SMP
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc6-00014-g10c8acb8b679 #524
[    0.000000] Hardware name: linux,dummy-virt (DT)
[    0.000000] pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    0.000000] pc : new_slab+0x190/0x340
[    0.000000] lr : new_slab+0x184/0x340
[    0.000000] sp : ffff80000a4b3d10

....
==================
The actual crash location and call stack will be somewhat random, and depend on the specific allocation of that physical memory range.

As the DT spec[1] explicitly mentions standard properties, add a simple check to skip over disabled memory nodes, so that we only use memory that is meant for non-secure code to use.

That fixes booting a QEMU arm64 VM with EL3 enabled ("secure=on"), when not using UEFI. In this case the QEMU generated DT will be handed on to the kernel, which will see the secram node.
This issue is reproducible when using TF-A together with U-Boot as firmware, then booting with the "booti" command.

When using U-Boot as an UEFI provider, the code there [2] explicitly filters for disabled nodes when generating the UEFI memory map, so we are safe.
EDK/2 only reads the first bank of the first DT memory node [3] to learn about memory, so we got lucky there.

[1] https://github.com/devicetree-org/devicetree-specification/blob/main/source/chapter3-devicenodes.rst#memory-node (after the table)
[2] https://source.denx.de/u-boot/u-boot/-/blob/master/lib/fdtdec.c#L1061-1063
[3] https://github.com/tianocore/edk2/blob/master/ArmVirtPkg/PrePi/FdtParser.c

---
 drivers/of/fdt.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/of/fdt.c +3 -0
index ec315b060cd5..0f30496ce80b 100644
@@ -1105,6 +1105,9 @@ int __init early_init_dt_scan_memory(void)
 		if (type == NULL || strcmp(type, "memory") != 0)
 			continue;
 
+		if (!of_fdt_device_is_available(fdt, node))
+			continue;
+
 		reg = of_get_flat_dt_prop(node, "linux,usable-memory", &l);
 		if (reg == NULL)
 			reg = of_get_flat_dt_prop(node, "reg", &l);
Signature · 1 line
2.35.1
author maintainer
#119 lore raw

PATCH 117/135 blk-throttle: Set BIO_THROTTLED when bio has been throttled

In reply to Sasha Levin

From: Laibin Qiu <[email protected]>

[ Upstream commit 5a011f889b4832aa80c2a872a5aade5c48d2756f ]

1.In current process, all bio will set the BIO_THROTTLED flag after __blk_throtl_bio().

2.If bio needs to be throttled, it will start the timer and stop submit bio directly. Bio will submit in blk_throtl_dispatch_work_fn() when the timer expires.But in the current process, if bio is throttled. The BIO_THROTTLED will be set to bio after timer start. If the bio has been completed, it may cause use-after-free blow.

BUG: KASAN: use-after-free in blk_throtl_bio+0x12f0/0x2c70
Read of size 2 at addr ffff88801b8902d4 by task fio/26380

 dump_stack+0x9b/0xce
 print_address_description.constprop.6+0x3e/0x60
 kasan_report.cold.9+0x22/0x3a
 blk_throtl_bio+0x12f0/0x2c70
 submit_bio_checks+0x701/0x1550
 submit_bio_noacct+0x83/0xc80
 submit_bio+0xa7/0x330
 mpage_readahead+0x380/0x500
 read_pages+0x1c1/0xbf0
 page_cache_ra_unbounded+0x471/0x6f0
 do_page_cache_ra+0xda/0x110
 ondemand_readahead+0x442/0xae0
 page_cache_async_ra+0x210/0x300
 generic_file_buffered_read+0x4d9/0x2130
 generic_file_read_iter+0x315/0x490
 blkdev_read_iter+0x113/0x1b0
 aio_read+0x2ad/0x450
 io_submit_one+0xc8e/0x1d60
 __se_sys_io_submit+0x125/0x350
 do_syscall_64+0x2d/0x40
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Allocated by task 26380:
 kasan_save_stack+0x19/0x40
 __kasan_kmalloc.constprop.2+0xc1/0xd0
 kmem_cache_alloc+0x146/0x440
 mempool_alloc+0x125/0x2f0
 bio_alloc_bioset+0x353/0x590
 mpage_alloc+0x3b/0x240
 do_mpage_readpage+0xddf/0x1ef0
 mpage_readahead+0x264/0x500
 read_pages+0x1c1/0xbf0
 page_cache_ra_unbounded+0x471/0x6f0
 do_page_cache_ra+0xda/0x110
 ondemand_readahead+0x442/0xae0
 page_cache_async_ra+0x210/0x300
 generic_file_buffered_read+0x4d9/0x2130
 generic_file_read_iter+0x315/0x490
 blkdev_read_iter+0x113/0x1b0
 aio_read+0x2ad/0x450
 io_submit_one+0xc8e/0x1d60
 __se_sys_io_submit+0x125/0x350
 do_syscall_64+0x2d/0x40
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Freed by task 0:
 kasan_save_stack+0x19/0x40
 kasan_set_track+0x1c/0x30
 kasan_set_free_info+0x1b/0x30
 __kasan_slab_free+0x111/0x160
 kmem_cache_free+0x94/0x460
 mempool_free+0xd6/0x320
 bio_free+0xe0/0x130
 bio_put+0xab/0xe0
 bio_endio+0x3a6/0x5d0
 blk_update_request+0x590/0x1370
 scsi_end_request+0x7d/0x400
 scsi_io_completion+0x1aa/0xe50
 scsi_softirq_done+0x11b/0x240
 blk_mq_complete_request+0xd4/0x120
 scsi_mq_done+0xf0/0x200
 virtscsi_vq_done+0xbc/0x150
 vring_interrupt+0x179/0x390
 __handle_irq_event_percpu+0xf7/0x490
 handle_irq_event_percpu+0x7b/0x160
 handle_irq_event+0xcc/0x170
 handle_edge_irq+0x215/0xb20
 common_interrupt+0x60/0x120
 asm_common_interrupt+0x1e/0x40

Fix this by move BIO_THROTTLED set into the queue_lock.

---
 block/blk-throttle.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
block/blk-throttle.c +2 -1
index 87769b337fc5..e1b253775a56 100644
@@ -2167,13 +2167,14 @@ bool __blk_throtl_bio(struct bio *bio)
 	}
 
 out_unlock:
-	spin_unlock_irq(&q->queue_lock);
 	bio_set_flag(bio, BIO_THROTTLED);
 
 #ifdef CONFIG_BLK_DEV_THROTTLING_LOW
 	if (throttled || !td->track_bio_latency)
 		bio->bi_issue.value |= BIO_ISSUE_THROTL_SKIP_LATENCY;
 #endif
+	spin_unlock_irq(&q->queue_lock);
+
 	rcu_read_unlock();
 	return throttled;
 }
Signature · 1 line
2.35.1
author maintainer
#120 lore raw

PATCH 118/135 ASoC: max98357a: remove dependency on GPIOLIB

In reply to Sasha Levin

From: Pierre-Louis Bossart <[email protected]>

[ Upstream commit 21ca3274333f5c1cbbf9d91e5b33f4f2463859b2 ]

commit dcc2c012c7691 ("ASoC: Fix gpiolib dependencies") removed a series of unnecessary dependencies on GPIOLIB when the gpio was optional.

A similar simplification seems valid for max98357a, so remove the dependency as well. This will avoid the following warning

   WARNING: unmet direct dependencies detected for SND_SOC_MAX98357A
     Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && GPIOLIB [=n]
     Selected by [y]:
     - SND_SOC_INTEL_SOF_CS42L42_MACH [=y] && SOUND [=y] && !UML &&
       SND [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
       (SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) && I2C
       [=y] && ACPI [=y] && SND_HDA_CODEC_HDMI [=y] &&
       SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=y] ||
       COMPILE_TEST [=n])
---
 sound/soc/codecs/Kconfig | 1 -
 1 file changed, 1 deletion(-)
sound/soc/codecs/Kconfig +0 -1
index 30c00380499c..a8c6c2bfd5a7 100644
@@ -943,7 +943,6 @@ config SND_SOC_MAX98095
 
 config SND_SOC_MAX98357A
 	tristate "Maxim MAX98357A CODEC"
-	depends on GPIOLIB
 
 config SND_SOC_MAX98371
 	tristate
Signature · 1 line
2.35.1
author maintainer
#121 lore raw

PATCH 119/135 ASoC: rt1015p: remove dependency on GPIOLIB

In reply to Sasha Levin

From: Pierre-Louis Bossart <[email protected]>

[ Upstream commit b390c25c6757b9d56cecdfbf6d55f15fc89a6386 ]

commit dcc2c012c7691 ("ASoC: Fix gpiolib dependencies") removed a series of unnecessary dependencies on GPIOLIB when the gpio was optional.

A similar simplification seems valid for rt1015p, so remove the dependency as well. This will avoid the following warning

WARNING: unmet direct dependencies detected for SND_SOC_RT1015P

     Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] &&
     GPIOLIB [=n]

     Selected by [y]:

     - SND_SOC_INTEL_SOF_RT5682_MACH [=y] && SOUND [=y] && !UML && SND
       [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
       (SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) && I2C
       [=y] && ACPI [=y] && (SND_HDA_CODEC_HDMI [=y] &&
       SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=y] ||
       COMPILE_TEST [=y]) || SND_SOC_SOF_BAYTRAIL [=n] &&
       (X86_INTEL_LPSS [=n] || COMPILE_TEST [=y]))
---
 sound/soc/codecs/Kconfig | 1 -
 1 file changed, 1 deletion(-)
sound/soc/codecs/Kconfig +0 -1
index a8c6c2bfd5a7..3496403004ac 100644
@@ -1202,7 +1202,6 @@ config SND_SOC_RT1015
 
 config SND_SOC_RT1015P
 	tristate
-	depends on GPIOLIB
 
 config SND_SOC_RT1019
 	tristate
Signature · 1 line
2.35.1
author maintainer
#122 lore raw

PATCH 120/135 ACPI: CPPC: Assume no transition latency if no PCCT

In reply to Sasha Levin

From: Pierre Gondois <[email protected]>

[ Upstream commit 6380b7b2b29da9d9c5ab2d4a265901cd93ba3696 ]

The transition_delay_us (struct cpufreq_policy) is currently defined as:
Preferred average time interval between consecutive invocations of the driver to set the frequency for this policy. To be set by the scaling driver (0, which is the default, means no preference).
The transition_latency represents the amount of time necessary for a CPU to change its frequency.

A PCCT table advertises mutliple values:
- pcc_nominal: Expected latency to process a command, in microseconds
- pcc_mpar: The maximum number of periodic requests that the subspace channel can support, reported in commands per minute. 0 indicates no limitation.
- pcc_mrtt: The minimum amount of time that OSPM must wait after the completion of a command before issuing the next command, in microseconds.
cppc_get_transition_latency() allows to get the max of them.

commit d4f3388afd48 ("cpufreq / CPPC: Set platform specific transition_delay_us") allows to select transition_delay_us based on the platform, and fallbacks to cppc_get_transition_latency() otherwise.

If _CPC objects are not using PCC channels (no PPCT table), the transition_delay_us is set to CPUFREQ_ETERNAL, leading to really long periods between frequency updates (~4s).

If the desired_reg, where performance requests are written, is in SystemMemory or SystemIo ACPI address space, there is no delay in requests. So return 0 instead of CPUFREQ_ETERNAL, leading to transition_delay_us being set to LATENCY_MULTIPLIER us (1000 us).

This patch also adds two macros to check the address spaces.

---
 drivers/acpi/cppc_acpi.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
drivers/acpi/cppc_acpi.c +16 -1
index 123e98a765de..a7facd4b4ca8 100644
@@ -100,6 +100,16 @@ static DEFINE_PER_CPU(struct cpc_desc *, cpc_desc_ptr);
 				(cpc)->cpc_entry.reg.space_id ==	\
 				ACPI_ADR_SPACE_PLATFORM_COMM)
 
+/* Check if a CPC register is in SystemMemory */
+#define CPC_IN_SYSTEM_MEMORY(cpc) ((cpc)->type == ACPI_TYPE_BUFFER &&	\
+				(cpc)->cpc_entry.reg.space_id ==	\
+				ACPI_ADR_SPACE_SYSTEM_MEMORY)
+
+/* Check if a CPC register is in SystemIo */
+#define CPC_IN_SYSTEM_IO(cpc) ((cpc)->type == ACPI_TYPE_BUFFER &&	\
+				(cpc)->cpc_entry.reg.space_id ==	\
+				ACPI_ADR_SPACE_SYSTEM_IO)
+
 /* Evaluates to True if reg is a NULL register descriptor */
 #define IS_NULL_REG(reg) ((reg)->space_id ==  ACPI_ADR_SPACE_SYSTEM_MEMORY && \
 				(reg)->address == 0 &&			\
@@ -1441,6 +1451,9 @@ EXPORT_SYMBOL_GPL(cppc_set_perf);
  * transition latency for performance change requests. The closest we have
  * is the timing information from the PCCT tables which provides the info
  * on the number and frequency of PCC commands the platform can handle.
+ *
+ * If desired_reg is in the SystemMemory or SystemIo ACPI address space,
+ * then assume there is no latency.
  */
 unsigned int cppc_get_transition_latency(int cpu_num)
 {
@@ -1466,7 +1479,9 @@ unsigned int cppc_get_transition_latency(int cpu_num)
 		return CPUFREQ_ETERNAL;
 
 	desired_reg = &cpc_desc->cpc_regs[DESIRED_PERF];
-	if (!CPC_IN_PCC(desired_reg))
+	if (CPC_IN_SYSTEM_MEMORY(desired_reg) || CPC_IN_SYSTEM_IO(desired_reg))
+		return 0;
+	else if (!CPC_IN_PCC(desired_reg))
 		return CPUFREQ_ETERNAL;
 
 	if (pcc_ss_id < 0)
Signature · 1 line
2.35.1
author maintainer
#123 lore raw

PATCH 121/135 nvme: set non-mdts limits in nvme_scan_work

In reply to Sasha Levin

From: Chaitanya Kulkarni <[email protected]>

[ Upstream commit 78288665b5d0154978fed431985310cb4f166836 ]

In current implementation we set the non-mdts limits by calling nvme_init_non_mdts_limits() from nvme_init_ctrl_finish(). This also tries to set the limits for the discovery controller which has no I/O queues resulting in the warning message reported by the nvme_log_error() when running blktest nvme/002: -

[ 2005.155946] run blktests nvme/002 at 2022-04-09 16:57:47
[ 2005.192223] loop: module loaded
[ 2005.196429] nvmet: adding nsid 1 to subsystem blktests-subsystem-0
[ 2005.200334] nvmet: adding nsid 1 to subsystem blktests-subsystem-1

<------------------------------SNIP---------------------------------->

[ 2008.958108] nvmet: adding nsid 1 to subsystem blktests-subsystem-997
[ 2008.962082] nvmet: adding nsid 1 to subsystem blktests-subsystem-998
[ 2008.966102] nvmet: adding nsid 1 to subsystem blktests-subsystem-999
[ 2008.973132] nvmet: creating discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN testhostnqn.
*[ 2008.973196] nvme1: Identify(0x6), Invalid Field in Command (sct 0x0 / sc 0x2) MORE DNR*
[ 2008.974595] nvme nvme1: new ctrl: "nqn.2014-08.org.nvmexpress.discovery"
[ 2009.103248] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"

Move the call of nvme_init_non_mdts_limits() to nvme_scan_work() after we verify that I/O queues are created since that is a converging point for each transport where these limits are actually used.

1. FC :
nvme_fc_create_association()
...
nvme_fc_create_io_queues(ctrl);
...
nvme_start_ctrl()
nvme_scan_queue()
nvme_scan_work()

2. PCIe:-
nvme_reset_work()
...
nvme_setup_io_queues()
nvme_create_io_queues()
nvme_alloc_queue()
...
nvme_start_ctrl()
nvme_scan_queue()
nvme_scan_work()

3. RDMA :-
nvme_rdma_setup_ctrl
...
nvme_rdma_configure_io_queues
...
nvme_start_ctrl()
nvme_scan_queue()
nvme_scan_work()

4. TCP :-
nvme_tcp_setup_ctrl
...
nvme_tcp_configure_io_queues
...
nvme_start_ctrl()
nvme_scan_queue()
nvme_scan_work()

* nvme_scan_work()
...
nvme_validate_or_alloc_ns()
nvme_alloc_ns()
nvme_update_ns_info()

    nvme_update_disk_info()
     nvme_config_discard() <---
     blk_queue_max_write_zeroes_sectors() <---
---
 drivers/nvme/host/core.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)
drivers/nvme/host/core.c +15 -4
index 0abd772c57f0..79ef46356d40 100644
@@ -3096,10 +3096,6 @@ int nvme_init_ctrl_finish(struct nvme_ctrl *ctrl)
 	if (ret)
 		return ret;
 
-	ret = nvme_init_non_mdts_limits(ctrl);
-	if (ret < 0)
-		return ret;
-
 	ret = nvme_configure_apst(ctrl);
 	if (ret < 0)
 		return ret;
@@ -4160,11 +4156,26 @@ static void nvme_scan_work(struct work_struct *work)
 {
 	struct nvme_ctrl *ctrl =
 		container_of(work, struct nvme_ctrl, scan_work);
+	int ret;
 
 	/* No tagset on a live ctrl means IO queues could not created */
 	if (ctrl->state != NVME_CTRL_LIVE || !ctrl->tagset)
 		return;
 
+	/*
+	 * Identify controller limits can change at controller reset due to
+	 * new firmware download, even though it is not common we cannot ignore
+	 * such scenario. Controller's non-mdts limits are reported in the unit
+	 * of logical blocks that is dependent on the format of attached
+	 * namespace. Hence re-read the limits at the time of ns allocation.
+	 */
+	ret = nvme_init_non_mdts_limits(ctrl);
+	if (ret < 0) {
+		dev_warn(ctrl->device,
+			"reading non-mdts-limits failed: %d\n", ret);
+		return;
+	}
+
 	if (test_and_clear_bit(NVME_AER_NOTICE_NS_CHANGED, &ctrl->events)) {
 		dev_info(ctrl->device, "rescanning namespaces.\n");
 		nvme_clear_changed_ns_log(ctrl);
Signature · 1 line
2.35.1
author maintainer
#124 lore raw

PATCH 122/135 can: mcp251xfd: silence clang's -Wunaligned-access warning

In reply to Sasha Levin

From: Vincent Mailhol <[email protected]>

[ Upstream commit 1a6dd9996699889313327be03981716a8337656b ]

clang emits a -Wunaligned-access warning on union
mcp251xfd_tx_ojb_load_buf.

The reason is that field hw_tx_obj (not declared as packed) is being packed right after a 16 bits field inside a packed struct:

| union mcp251xfd_tx_obj_load_buf {
| 	struct __packed {
| 		struct mcp251xfd_buf_cmd cmd;
| 		  /* ^ 16 bits fields */
| 		struct mcp251xfd_hw_tx_obj_raw hw_tx_obj;
| 		  /* ^ not declared as packed */
| 	} nocrc;
| 	struct __packed {
| 		struct mcp251xfd_buf_cmd_crc cmd;
| 		struct mcp251xfd_hw_tx_obj_raw hw_tx_obj;
| 		__be16 crc;
| 	} crc;
| } ____cacheline_aligned;

Starting from LLVM 14, having an unpacked struct nested in a packed struct triggers a warning. c.f. [1].

This is a false positive because the field is always being accessed with the relevant put_unaligned_*() function. Adding __packed to the structure declaration silences the warning.

[1] https://github.com/llvm/llvm-project/issues/55520

---
 drivers/net/can/spi/mcp251xfd/mcp251xfd.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/can/spi/mcp251xfd/mcp251xfd.h +1 -1
index f551c900803e..aed6e9d47517 100644
@@ -434,7 +434,7 @@ struct mcp251xfd_hw_tef_obj {
 /* The tx_obj_raw version is used in spi async, i.e. without
  * regmap. We have to take care of endianness ourselves.
  */
-struct mcp251xfd_hw_tx_obj_raw {
+struct __packed mcp251xfd_hw_tx_obj_raw {
 	__le32 id;
 	__le32 flags;
 	u8 data[sizeof_field(struct canfd_frame, data)];
Signature · 1 line
2.35.1
author maintainer
#125 lore raw

PATCH 123/135 x86/microcode: Add explicit CPU vendor dependency

In reply to Sasha Levin

From: Borislav Petkov <[email protected]>

[ Upstream commit 9c55d99e099bd7aa6b91fce8718505c35d5dfc65 ]

Add an explicit dependency to the respective CPU vendor so that the respective microcode support for it gets built only when that support is enabled.

---
 arch/x86/Kconfig | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/Kconfig +2 -2
index d0ecc4005df3..380c16ff5078 100644
@@ -1332,7 +1332,7 @@ config MICROCODE
 
 config MICROCODE_INTEL
 	bool "Intel microcode loading support"
-	depends on MICROCODE
+	depends on CPU_SUP_INTEL && MICROCODE
 	default MICROCODE
 	help
 	  This options enables microcode patch loading support for Intel
@@ -1344,7 +1344,7 @@ config MICROCODE_INTEL
 
 config MICROCODE_AMD
 	bool "AMD microcode loading support"
-	depends on MICROCODE
+	depends on CPU_SUP_AMD && MICROCODE
 	help
 	  If you select this option, microcode patch loading support for AMD
 	  processors will be enabled.
Signature · 1 line
2.35.1
author maintainer
#126 lore raw

PATCH 124/135 net: ipa: ignore endianness if there is no header

In reply to Sasha Levin

From: Alex Elder <[email protected]>

[ Upstream commit 332ef7c814bdd60f08d0d9013d0e1104798b2d23 ]

If we program an RX endpoint to have no header (header length is 0), header-related endpoint configuration values are meaningless and are ignored.

The only case we support that defines a header is QMAP endpoints. In ipa_endpoint_init_hdr_ext() we set the endianness mask value unconditionally, but it should not be done if there is no header (meaning it is not configured for QMAP).

Set the endianness conditionally, and rearrange the logic in that function slightly to avoid testing the qmap flag twice.

Delete an incorrect comment in ipa_endpoint_init_aggr().

---
 drivers/net/ipa/ipa_endpoint.c | 32 +++++++++++++++++---------------
 1 file changed, 17 insertions(+), 15 deletions(-)
drivers/net/ipa/ipa_endpoint.c +17 -15
index 2ecfc17544a6..58b3a2d15d31 100644
@@ -571,19 +571,23 @@ static void ipa_endpoint_init_hdr_ext(struct ipa_endpoint *endpoint)
 	struct ipa *ipa = endpoint->ipa;
 	u32 val = 0;
 
-	val |= HDR_ENDIANNESS_FMASK;		/* big endian */
-
-	/* A QMAP header contains a 6 bit pad field at offset 0.  The RMNet
-	 * driver assumes this field is meaningful in packets it receives,
-	 * and assumes the header's payload length includes that padding.
-	 * The RMNet driver does *not* pad packets it sends, however, so
-	 * the pad field (although 0) should be ignored.
-	 */
-	if (endpoint->data->qmap && !endpoint->toward_ipa) {
-		val |= HDR_TOTAL_LEN_OR_PAD_VALID_FMASK;
-		/* HDR_TOTAL_LEN_OR_PAD is 0 (pad, not total_len) */
-		val |= HDR_PAYLOAD_LEN_INC_PADDING_FMASK;
-		/* HDR_TOTAL_LEN_OR_PAD_OFFSET is 0 */
+	if (endpoint->data->qmap) {
+		/* We have a header, so we must specify its endianness */
+		val |= HDR_ENDIANNESS_FMASK;	/* big endian */
+
+		/* A QMAP header contains a 6 bit pad field at offset 0.
+		 * The RMNet driver assumes this field is meaningful in
+		 * packets it receives, and assumes the header's payload
+		 * length includes that padding.  The RMNet driver does
+		 * *not* pad packets it sends, however, so the pad field
+		 * (although 0) should be ignored.
+		 */
+		if (!endpoint->toward_ipa) {
+			val |= HDR_TOTAL_LEN_OR_PAD_VALID_FMASK;
+			/* HDR_TOTAL_LEN_OR_PAD is 0 (pad, not total_len) */
+			val |= HDR_PAYLOAD_LEN_INC_PADDING_FMASK;
+			/* HDR_TOTAL_LEN_OR_PAD_OFFSET is 0 */
+		}
 	}
 
 	/* HDR_PAYLOAD_LEN_INC_PADDING is 0 */
@@ -739,8 +743,6 @@ static void ipa_endpoint_init_aggr(struct ipa_endpoint *endpoint)
 
 			close_eof = endpoint->data->rx.aggr_close_eof;
 			val |= aggr_sw_eof_active_encoded(version, close_eof);
-
-			/* AGGR_HARD_BYTE_LIMIT_ENABLE is 0 */
 		} else {
 			val |= u32_encode_bits(IPA_ENABLE_DEAGGR,
 					       AGGR_EN_FMASK);
Signature · 1 line
2.35.1
author maintainer
#127 lore raw

PATCH 125/135 ARM: 9201/1: spectre-bhb: rely on linker to emit cross-section literal loads

In reply to Sasha Levin

From: Ard Biesheuvel <[email protected]>

[ Upstream commit ad12c2f1587c6ec9b52ff226f438955bfae6ad89 ]

The assembler does not permit 'LDR PC, <sym>' when the symbol lives in a different section, which is why we have been relying on rather fragile open-coded arithmetic to load the address of the vector_swi routine into the program counter using a single LDR instruction in the SWI slot in the vector table. The literal was moved to a different section to in commit 19accfd373847 ("ARM: move vector stubs") to ensure that the vector stubs page does not need to be mapped readable for user space, which is the case for the vector page itself, as it carries the kuser helpers as well.

So the cross-section literal load is open-coded, and this relies on the address of vector_swi to be at the very start of the vector stubs page, and we won't notice if we got it wrong until booting the kernel and see it break. Fortunately, it was guaranteed to break, so this was fragile but not problematic.

Now that we have added two other variants of the vector table, we have 3 occurrences of the same trick, and so the size of our ISA/compiler/CPU validation space has tripled, in a way that may cause regressions to only be observed once booting the image in question on a CPU that exercises a particular vector table.

So let's switch to true cross section references, and let the linker fix them up like it fixes up all the other cross section references in the vector page.

---
 arch/arm/kernel/entry-armv.S | 22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)
arch/arm/kernel/entry-armv.S +15 -7
index 4bbd92d41031..bc536c6fcf2d 100644
@@ -1071,10 +1071,15 @@ ENDPROC(vector_bhb_bpiall_\name)
 	.endm
 
 	.section .stubs, "ax", %progbits
-	@ This must be the first word
+	@ These need to remain at the start of the section so that
+	@ they are in range of the 'SWI' entries in the vector tables
+	@ located 4k down.
+.L__vector_swi:
 	.word	vector_swi
 #ifdef CONFIG_HARDEN_BRANCH_HISTORY
+.L__vector_bhb_loop8_swi:
 	.word	vector_bhb_loop8_swi
+.L__vector_bhb_bpiall_swi:
 	.word	vector_bhb_bpiall_swi
 #endif
 
@@ -1217,10 +1222,11 @@ vector_addrexcptn:
 	.globl	vector_fiq
 
 	.section .vectors, "ax", %progbits
-.L__vectors_start:
 	W(b)	vector_rst
 	W(b)	vector_und
-	W(ldr)	pc, .L__vectors_start + 0x1000
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_swi		)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_swi		)
+	W(ldr)	pc, .
 	W(b)	vector_pabt
 	W(b)	vector_dabt
 	W(b)	vector_addrexcptn
@@ -1229,10 +1235,11 @@ vector_addrexcptn:
 
 #ifdef CONFIG_HARDEN_BRANCH_HISTORY
 	.section .vectors.bhb.loop8, "ax", %progbits
-.L__vectors_bhb_loop8_start:
 	W(b)	vector_rst
 	W(b)	vector_bhb_loop8_und
-	W(ldr)	pc, .L__vectors_bhb_loop8_start + 0x1004
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_bhb_loop8_swi	)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_bhb_loop8_swi	)
+	W(ldr)	pc, .
 	W(b)	vector_bhb_loop8_pabt
 	W(b)	vector_bhb_loop8_dabt
 	W(b)	vector_addrexcptn
@@ -1240,10 +1247,11 @@ vector_addrexcptn:
 	W(b)	vector_bhb_loop8_fiq
 
 	.section .vectors.bhb.bpiall, "ax", %progbits
-.L__vectors_bhb_bpiall_start:
 	W(b)	vector_rst
 	W(b)	vector_bhb_bpiall_und
-	W(ldr)	pc, .L__vectors_bhb_bpiall_start + 0x1008
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_bhb_bpiall_swi	)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_bhb_bpiall_swi	)
+	W(ldr)	pc, .
 	W(b)	vector_bhb_bpiall_pabt
 	W(b)	vector_bhb_bpiall_dabt
 	W(b)	vector_addrexcptn
Signature · 7 lines
2.35.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#128 lore raw

Re: [PATCH AUTOSEL 5.17 125/135] ARM: 9201/1: spectre-bhb: rely on linker to emit cross-section literal loads

AUTONAK

Quoted 102 lines · Sasha Levin

From: Ard Biesheuvel <[email protected]>

[ Upstream commit ad12c2f1587c6ec9b52ff226f438955bfae6ad89 ]

The assembler does not permit 'LDR PC, <sym>' when the symbol lives in a different section, which is why we have been relying on rather fragile open-coded arithmetic to load the address of the vector_swi routine into the program counter using a single LDR instruction in the SWI slot in the vector table. The literal was moved to a different section to in commit 19accfd373847 ("ARM: move vector stubs") to ensure that the vector stubs page does not need to be mapped readable for user space, which is the case for the vector page itself, as it carries the kuser helpers as well.

So the cross-section literal load is open-coded, and this relies on the address of vector_swi to be at the very start of the vector stubs page, and we won't notice if we got it wrong until booting the kernel and see it break. Fortunately, it was guaranteed to break, so this was fragile but not problematic.

Now that we have added two other variants of the vector table, we have 3 occurrences of the same trick, and so the size of our ISA/compiler/CPU validation space has tripled, in a way that may cause regressions to only be observed once booting the image in question on a CPU that exercises a particular vector table.

So let's switch to true cross section references, and let the linker fix them up like it fixes up all the other cross section references in the vector page.

---
 arch/arm/kernel/entry-armv.S | 22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)
arch/arm/kernel/entry-armv.S +15 -8
index 4bbd92d41031..bc536c6fcf2d 100644
@@ -1071,10 +1071,15 @@ ENDPROC(vector_bhb_bpiall_\name)
        .endm
 
        .section .stubs, "ax", %progbits
-       @ This must be the first word
+       @ These need to remain at the start of the section so that
+       @ they are in range of the 'SWI' entries in the vector tables
+       @ located 4k down.
+.L__vector_swi:
        .word   vector_swi
 #ifdef CONFIG_HARDEN_BRANCH_HISTORY
+.L__vector_bhb_loop8_swi:
        .word   vector_bhb_loop8_swi
+.L__vector_bhb_bpiall_swi:
        .word   vector_bhb_bpiall_swi
 #endif
 
@@ -1217,10 +1222,11 @@ vector_addrexcptn:
        .globl  vector_fiq
 
        .section .vectors, "ax", %progbits
-.L__vectors_start:
        W(b)    vector_rst
        W(b)    vector_und
-       W(ldr)  pc, .L__vectors_start + 0x1000
+ARM(   .reloc  ., R_ARM_LDR_PC_G0, .L__vector_swi              )
+THUMB( .reloc  ., R_ARM_THM_PC12, .L__vector_swi               )
+       W(ldr)  pc, .
        W(b)    vector_pabt
        W(b)    vector_dabt
        W(b)    vector_addrexcptn
@@ -1229,10 +1235,11 @@ vector_addrexcptn:
 
 #ifdef CONFIG_HARDEN_BRANCH_HISTORY
        .section .vectors.bhb.loop8, "ax", %progbits
-.L__vectors_bhb_loop8_start:
        W(b)    vector_rst
        W(b)    vector_bhb_loop8_und
-       W(ldr)  pc, .L__vectors_bhb_loop8_start + 0x1004
+ARM(   .reloc  ., R_ARM_LDR_PC_G0, .L__vector_bhb_loop8_swi    )
+THUMB( .reloc  ., R_ARM_THM_PC12, .L__vector_bhb_loop8_swi     )
+       W(ldr)  pc, .
        W(b)    vector_bhb_loop8_pabt
        W(b)    vector_bhb_loop8_dabt
        W(b)    vector_addrexcptn
@@ -1240,10 +1247,11 @@ vector_addrexcptn:
        W(b)    vector_bhb_loop8_fiq
 
        .section .vectors.bhb.bpiall, "ax", %progbits
-.L__vectors_bhb_bpiall_start:
        W(b)    vector_rst
        W(b)    vector_bhb_bpiall_und
-       W(ldr)  pc, .L__vectors_bhb_bpiall_start + 0x1008
+ARM(   .reloc  ., R_ARM_LDR_PC_G0, .L__vector_bhb_bpiall_swi   )
+THUMB( .reloc  ., R_ARM_THM_PC12, .L__vector_bhb_bpiall_swi    )
+       W(ldr)  pc, .
        W(b)    vector_bhb_bpiall_pabt
        W(b)    vector_bhb_bpiall_dabt
        W(b)    vector_addrexcptn
--
Quoted 2 lines

2.35.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author maintainer
#129 lore raw

PATCH 126/135 selftests/bpf: Add missing trampoline program type to trampoline_count test

In reply to Sasha Levin

From: Yuntao Wang <[email protected]>

[ Upstream commit b23316aabffa835ecc516cb81daeef5b9155e8a5 ]

Currently the trampoline_count test doesn't include any fmod_ret bpf programs, fix it to make the test cover all possible trampoline program types.

Since fmod_ret bpf programs can't be attached to __set_task_comm function, as it's neither whitelisted for error injection nor a security hook, change it to bpf_modify_return_test.

This patch also does some other cleanups such as removing duplicate code, dropping inconsistent comments, etc.

---
 include/linux/bpf.h                           |   2 +-
 .../bpf/prog_tests/trampoline_count.c         | 134 +++++++-----------
 .../bpf/progs/test_trampoline_count.c         |  16 ++-
 3 files changed, 61 insertions(+), 91 deletions(-)
include/linux/bpf.h +1 -1
index 3121d1fc8e75..2f7e00e7af37 100644
@@ -652,7 +652,7 @@ struct btf_func_model {
 #define BPF_TRAMP_F_RET_FENTRY_RET	BIT(4)
 
 /* Each call __bpf_prog_enter + call bpf_func + call __bpf_prog_exit is ~50
- * bytes on x86.  Pick a number to fit into BPF_IMAGE_SIZE / 2
+ * bytes on x86.
  */
 #define BPF_MAX_TRAMP_PROGS 38
 
tools/testing/selftests/bpf/prog_tests/trampoline_count.c +51 -83

177 lines not on this page · raw message

tools/testing/selftests/bpf/progs/test_trampoline_count.c +9 -7
index f030e469d05b..7765720da7d5 100644
@@ -1,20 +1,22 @@
 // SPDX-License-Identifier: GPL-2.0
-#include <stdbool.h>
-#include <stddef.h>
 #include <linux/bpf.h>
 #include <bpf/bpf_helpers.h>
 #include <bpf/bpf_tracing.h>
 
-struct task_struct;
+SEC("fentry/bpf_modify_return_test")
+int BPF_PROG(fentry_test, int a, int *b)
+{
+	return 0;
+}
 
-SEC("fentry/__set_task_comm")
-int BPF_PROG(prog1, struct task_struct *tsk, const char *buf, bool exec)
+SEC("fmod_ret/bpf_modify_return_test")
+int BPF_PROG(fmod_ret_test, int a, int *b, int ret)
 {
 	return 0;
 }
 
-SEC("fexit/__set_task_comm")
-int BPF_PROG(prog2, struct task_struct *tsk, const char *buf, bool exec)
+SEC("fexit/bpf_modify_return_test")
+int BPF_PROG(fexit_test, int a, int *b, int ret)
 {
 	return 0;
 }
Signature · 1 line
2.35.1
author maintainer
#130 lore raw

PATCH 127/135 m68k: atari: Make Atari ROM port I/O write macros return void

In reply to Sasha Levin

From: Geert Uytterhoeven <[email protected]>

[ Upstream commit 30b5e6ef4a32ea4985b99200e06d6660a69f9246 ]

The macros implementing Atari ROM port I/O writes do not cast away their output, unlike similar implementations for other I/O buses. When they are combined using conditional expressions in the definitions of outb() and friends, this triggers sparse warnings like:

drivers/net/appletalk/cops.c:382:17: error: incompatible types in conditional expression (different base types):
drivers/net/appletalk/cops.c:382:17: unsigned char
drivers/net/appletalk/cops.c:382:17: void

Fix this by adding casts to "void".

---
 arch/m68k/include/asm/raw_io.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/m68k/include/asm/raw_io.h +3 -3
index 80eb2396d01e..3ba40bc1dfaa 100644
@@ -80,14 +80,14 @@
 	({ u16 __v = le16_to_cpu(*(__force volatile u16 *) (addr)); __v; })
 
 #define rom_out_8(addr, b)	\
-	({u8 __maybe_unused __w, __v = (b);  u32 _addr = ((u32) (addr)); \
+	(void)({u8 __maybe_unused __w, __v = (b);  u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u8 *)  ((_addr | 0x10000) + (__v<<1)))); })
 #define rom_out_be16(addr, w)	\
-	({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
+	(void)({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u16 *) ((_addr & 0xFFFF0000UL) + ((__v & 0xFF)<<1)))); \
 	__w = ((*(__force volatile u16 *) ((_addr | 0x10000) + ((__v >> 8)<<1)))); })
 #define rom_out_le16(addr, w)	\
-	({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
+	(void)({u16 __maybe_unused __w, __v = (w); u32 _addr = ((u32) (addr)); \
 	__w = ((*(__force volatile u16 *) ((_addr & 0xFFFF0000UL) + ((__v >> 8)<<1)))); \
 	__w = ((*(__force volatile u16 *) ((_addr | 0x10000) + ((__v & 0xFF)<<1)))); })
 
Signature · 1 line
2.35.1
author maintainer
#131 lore raw

PATCH 128/135 hwmon: Make chip parameter for with_info API mandatory

In reply to Sasha Levin

From: Guenter Roeck <[email protected]>

[ Upstream commit ddaefa209c4ac791c1262e97c9b2d0440c8ef1d5 ]

Various attempts were made recently to "convert" the old hwmon_device_register() API to devm_hwmon_device_register_with_info() by just changing the function name without actually converting the driver. Prevent this from happening by making the 'chip' parameter of devm_hwmon_device_register_with_info() mandatory.

---
 Documentation/hwmon/hwmon-kernel-api.rst |  2 +-
 drivers/hwmon/hwmon.c                    | 16 +++++++---------
 2 files changed, 8 insertions(+), 10 deletions(-)
Documentation/hwmon/hwmon-kernel-api.rst +1 -1
index c41eb6108103..23f27fe78e37 100644
@@ -72,7 +72,7 @@ hwmon_device_register_with_info is the most comprehensive and preferred means
 to register a hardware monitoring device. It creates the standard sysfs
 attributes in the hardware monitoring core, letting the driver focus on reading
 from and writing to the chip instead of having to bother with sysfs attributes.
-The parent device parameter cannot be NULL with non-NULL chip info. Its
+The parent device parameter as well as the chip parameter must not be NULL. Its
 parameters are described in more detail below.
 
 devm_hwmon_device_register_with_info is similar to
drivers/hwmon/hwmon.c +7 -9
index 3ae961986fc3..55237a5fc49a 100644
@@ -854,11 +854,12 @@ EXPORT_SYMBOL_GPL(hwmon_device_register_with_groups);
 
 /**
  * hwmon_device_register_with_info - register w/ hwmon
- * @dev: the parent device
- * @name: hwmon name attribute
- * @drvdata: driver data to attach to created device
- * @chip: pointer to hwmon chip information
+ * @dev: the parent device (mandatory)
+ * @name: hwmon name attribute (mandatory)
+ * @drvdata: driver data to attach to created device (optional)
+ * @chip: pointer to hwmon chip information (mandatory)
  * @extra_groups: pointer to list of additional non-standard attribute groups
+ *	(optional)
  *
  * hwmon_device_unregister() must be called when the device is no
  * longer needed.
@@ -871,13 +872,10 @@ hwmon_device_register_with_info(struct device *dev, const char *name,
 				const struct hwmon_chip_info *chip,
 				const struct attribute_group **extra_groups)
 {
-	if (!name)
-		return ERR_PTR(-EINVAL);
-
-	if (chip && (!chip->ops || !chip->ops->is_visible || !chip->info))
+	if (!dev || !name || !chip)
 		return ERR_PTR(-EINVAL);
 
-	if (chip && !dev)
+	if (!chip->ops || !chip->ops->is_visible || !chip->info)
 		return ERR_PTR(-EINVAL);
 
 	return __hwmon_device_register(dev, name, drvdata, chip, extra_groups);
Signature · 1 line
2.35.1
maintainer
#132 lore raw

Re: [PATCH AUTOSEL 5.17 128/135] hwmon: Make chip parameter for with_info API mandatory

Quoted 4 lines · Sasha Levin

From: Guenter Roeck <[email protected]>

[ Upstream commit ddaefa209c4ac791c1262e97c9b2d0440c8ef1d5 ]

Quoted 8 lines

Various attempts were made recently to "convert" the old hwmon_device_register() API to devm_hwmon_device_register_with_info() by just changing the function name without actually converting the driver. Prevent this from happening by making the 'chip' parameter of devm_hwmon_device_register_with_info() mandatory.

This patch should not be backported. It is only relevant for new kernel releases, and may have adverse affect if applied to older kernels.

Guenter

Quoted 55 lines
---
  Documentation/hwmon/hwmon-kernel-api.rst |  2 +-
  drivers/hwmon/hwmon.c                    | 16 +++++++---------
  2 files changed, 8 insertions(+), 10 deletions(-)
Documentation/hwmon/hwmon-kernel-api.rst +1 -1
index c41eb6108103..23f27fe78e37 100644
@@ -72,7 +72,7 @@ hwmon_device_register_with_info is the most comprehensive and preferred means
  to register a hardware monitoring device. It creates the standard sysfs
  attributes in the hardware monitoring core, letting the driver focus on reading
  from and writing to the chip instead of having to bother with sysfs attributes.
-The parent device parameter cannot be NULL with non-NULL chip info. Its
+The parent device parameter as well as the chip parameter must not be NULL. Its
  parameters are described in more detail below.
 
  devm_hwmon_device_register_with_info is similar to
drivers/hwmon/hwmon.c +7 -9
index 3ae961986fc3..55237a5fc49a 100644
@@ -854,11 +854,12 @@ EXPORT_SYMBOL_GPL(hwmon_device_register_with_groups);
 
  /**
   * hwmon_device_register_with_info - register w/ hwmon
- * @dev: the parent device
- * @name: hwmon name attribute
- * @drvdata: driver data to attach to created device
- * @chip: pointer to hwmon chip information
+ * @dev: the parent device (mandatory)
+ * @name: hwmon name attribute (mandatory)
+ * @drvdata: driver data to attach to created device (optional)
+ * @chip: pointer to hwmon chip information (mandatory)
   * @extra_groups: pointer to list of additional non-standard attribute groups
+ *	(optional)
   *
   * hwmon_device_unregister() must be called when the device is no
   * longer needed.
@@ -871,13 +872,10 @@ hwmon_device_register_with_info(struct device *dev, const char *name,
  				const struct hwmon_chip_info *chip,
  				const struct attribute_group **extra_groups)
  {
-	if (!name)
-		return ERR_PTR(-EINVAL);
-
-	if (chip && (!chip->ops || !chip->ops->is_visible || !chip->info))
+	if (!dev || !name || !chip)
  		return ERR_PTR(-EINVAL);
 
-	if (chip && !dev)
+	if (!chip->ops || !chip->ops->is_visible || !chip->info)
  		return ERR_PTR(-EINVAL);
 
  	return __hwmon_device_register(dev, name, drvdata, chip, extra_groups);
#133 lore raw

Re: [PATCH AUTOSEL 5.17 128/135] hwmon: Make chip parameter for with_info API mandatory

Quoted 11 lines · Guenter Roeck
Quoted 10 lines · Sasha Levin

From: Guenter Roeck <[email protected]>

[ Upstream commit ddaefa209c4ac791c1262e97c9b2d0440c8ef1d5 ]

Various attempts were made recently to "convert" the old hwmon_device_register() API to devm_hwmon_device_register_with_info() by just changing the function name without actually converting the driver. Prevent this from happening by making the 'chip' parameter of devm_hwmon_device_register_with_info() mandatory.

Quoted 6 lines
Quoted 2 lines

This patch should not be backported. It is only relevant for new kernel releases, and may have adverse affect if applied to older kernels.

So this patch is meant to be backported to 5.18 only, right?

Signature · 1 line
An old man doll... just what I always wanted! - Clara
maintainer
#134 lore raw

Re: [PATCH AUTOSEL 5.17 128/135] hwmon: Make chip parameter for with_info API mandatory

Quoted 12 lines · Bagas Sanjaya
Quoted 11 lines · Guenter Roeck
Quoted 10 lines · Sasha Levin

From: Guenter Roeck <[email protected]>

[ Upstream commit ddaefa209c4ac791c1262e97c9b2d0440c8ef1d5 ]

Various attempts were made recently to "convert" the old hwmon_device_register() API to devm_hwmon_device_register_with_info() by just changing the function name without actually converting the driver. Prevent this from happening by making the 'chip' parameter of devm_hwmon_device_register_with_info() mandatory.

Quoted 9 lines
Quoted 6 lines
Quoted 2 lines

This patch should not be backported. It is only relevant for new kernel releases, and may have adverse affect if applied to older kernels.

So this patch is meant to be backported to 5.18 only, right?

I said "do not backport". I specifically asked not to backport this patch. It does not include Cc: stable, and it does not include a Fixes: tag. I even said "... may have adverse affect if applied to older kernels".

I have no idea how that can be interpreted as "backport to 5.18". Did I miss the explicit "do not backport to 5.18 ?" If so, my bad.

Ok, here it is a more explicit request:

Do not backport this patch to 5.18.y, 5.17.y, 5.15.y, 5.10.y, 5.4.y, 4.19.y, 4.14.y, 4.9.y, or any other stable release.

Guenter

author maintainer
#135 lore raw

PATCH 129/135 rxrpc: Return an error to sendmsg if call failed

In reply to Sasha Levin

From: David Howells <[email protected]>

[ Upstream commit 4ba68c5192554876bd8c3afd904e3064d2915341 ]

If at the end of rxrpc sendmsg() or rxrpc_kernel_send_data() the call that was being given data was aborted remotely or otherwise failed, return an error rather than returning the amount of data buffered for transmission.

The call (presumably) did not complete, so there's not much point continuing with it. AF_RXRPC considers it "complete" and so will be unwilling to do anything else with it - and won't send a notification for it, deeming the return from sendmsg sufficient.

Not returning an error causes afs to incorrectly handle a StoreData operation that gets interrupted by a change of address due to NAT reconfiguration.

This doesn't normally affect most operations since their request parameters tend to fit into a single UDP packet and afs_make_call() returns before the server responds; StoreData is different as it involves transmission of a lot of data.

This can be triggered on a client by doing something like:

	dd if=/dev/zero of=/afs/example.com/foo bs=1M count=512

at one prompt, and then changing the network address at another prompt, e.g.:

	ifconfig enp6s0 inet 192.168.6.2 && route add 192.168.6.1 dev enp6s0

Tracing packets on an Auristor fileserver looks something like:

192.168.6.1 -> 192.168.6.3  RX 107 ACK Idle  Seq: 0  Call: 4  Source Port: 7000  Destination Port: 7001
192.168.6.3 -> 192.168.6.1  AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.3 -> 192.168.6.1  AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.1 -> 192.168.6.3  RX 107 ACK Idle  Seq: 0  Call: 4  Source Port: 7000  Destination Port: 7001
<ARP exchange for 192.168.6.2>
192.168.6.2 -> 192.168.6.1  AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.2 -> 192.168.6.1  AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.1 -> 192.168.6.2  RX 107 ACK Exceeds Window  Seq: 0  Call: 4  Source Port: 7000  Destination Port: 7001
192.168.6.1 -> 192.168.6.2  RX 74 ABORT  Seq: 0  Call: 4  Source Port: 7000  Destination Port: 7001
192.168.6.1 -> 192.168.6.2  RX 74 ABORT  Seq: 29321  Call: 4  Source Port: 7000  Destination Port: 7001

The Auristor fileserver logs code -453 (RXGEN_SS_UNMARSHAL), but the abort code received by kafs is -5 (RX_PROTOCOL_ERROR) as the rx layer sees the condition and generates an abort first and the unmarshal error is a consequence of that at the application layer.

---
 net/rxrpc/sendmsg.c | 6 ++++++
 1 file changed, 6 insertions(+)
net/rxrpc/sendmsg.c +6 -0
index af8ad6c30b9f..1d38e279e2ef 100644
@@ -444,6 +444,12 @@ static int rxrpc_send_data(struct rxrpc_sock *rx,
 
 success:
 	ret = copied;
+	if (READ_ONCE(call->state) == RXRPC_CALL_COMPLETE) {
+		read_lock_bh(&call->state_lock);
+		if (call->error < 0)
+			ret = call->error;
+		read_unlock_bh(&call->state_lock);
+	}
 out:
 	call->tx_pending = skb;
 	_leave(" = %d", ret);
Signature · 1 line
2.35.1
author maintainer
#136 lore raw

PATCH 130/135 rxrpc, afs: Fix selection of abort codes

In reply to Sasha Levin

From: David Howells <[email protected]>

[ Upstream commit de696c4784f0706884458893c5a6c39b3a3ff65c ]

The RX_USER_ABORT code should really only be used to indicate that the user of the rxrpc service (ie. userspace) implicitly caused a call to be aborted
- for instance if the AF_RXRPC socket is closed whilst the call was in progress. (The user may also explicitly abort a call and specify the abort code to use).

Change some of the points of generation to use other abort codes instead:

(1) Abort the call with RXGEN_SS_UNMARSHAL or RXGEN_CC_UNMARSHAL if we see ENOMEM and EFAULT during received data delivery and abort with RX_CALL_DEAD in the default case.

(2) Abort with RXGEN_SS_MARSHAL if we get ENOMEM whilst trying to send a reply.

(3) Abort with RX_CALL_DEAD if we stop hearing from the peer if we had heard from the peer and abort with RX_CALL_TIMEOUT if we hadn't.

(4) Abort with RX_CALL_DEAD if we try to disconnect a call that's not completed successfully or been aborted.

---
 fs/afs/rxrpc.c          | 8 +++++---
 net/rxrpc/call_event.c  | 4 ++--
 net/rxrpc/conn_object.c | 2 +-
 3 files changed, 8 insertions(+), 6 deletions(-)
fs/afs/rxrpc.c +5 -3
index 23a1a92d64bb..a5434f3e57c6 100644
@@ -537,6 +537,8 @@ static void afs_deliver_to_call(struct afs_call *call)
 		case -ENODATA:
 		case -EBADMSG:
 		case -EMSGSIZE:
+		case -ENOMEM:
+		case -EFAULT:
 			abort_code = RXGEN_CC_UNMARSHAL;
 			if (state != AFS_CALL_CL_AWAIT_REPLY)
 				abort_code = RXGEN_SS_UNMARSHAL;
@@ -544,7 +546,7 @@ static void afs_deliver_to_call(struct afs_call *call)
 						abort_code, ret, "KUM");
 			goto local_abort;
 		default:
-			abort_code = RX_USER_ABORT;
+			abort_code = RX_CALL_DEAD;
 			rxrpc_kernel_abort_call(call->net->socket, call->rxcall,
 						abort_code, ret, "KER");
 			goto local_abort;
@@ -836,7 +838,7 @@ void afs_send_empty_reply(struct afs_call *call)
 	case -ENOMEM:
 		_debug("oom");
 		rxrpc_kernel_abort_call(net->socket, call->rxcall,
-					RX_USER_ABORT, -ENOMEM, "KOO");
+					RXGEN_SS_MARSHAL, -ENOMEM, "KOO");
 		fallthrough;
 	default:
 		_leave(" [error]");
@@ -878,7 +880,7 @@ void afs_send_simple_reply(struct afs_call *call, const void *buf, size_t len)
 	if (n == -ENOMEM) {
 		_debug("oom");
 		rxrpc_kernel_abort_call(net->socket, call->rxcall,
-					RX_USER_ABORT, -ENOMEM, "KOO");
+					RXGEN_SS_MARSHAL, -ENOMEM, "KOO");
 	}
 	_leave(" [error]");
 }
net/rxrpc/call_event.c +2 -2
index 22e05de5d1ca..e426f6831aab 100644
@@ -377,9 +377,9 @@ void rxrpc_process_call(struct work_struct *work)
 		if (test_bit(RXRPC_CALL_RX_HEARD, &call->flags) &&
 		    (int)call->conn->hi_serial - (int)call->rx_serial > 0) {
 			trace_rxrpc_call_reset(call);
-			rxrpc_abort_call("EXP", call, 0, RX_USER_ABORT, -ECONNRESET);
+			rxrpc_abort_call("EXP", call, 0, RX_CALL_DEAD, -ECONNRESET);
 		} else {
-			rxrpc_abort_call("EXP", call, 0, RX_USER_ABORT, -ETIME);
+			rxrpc_abort_call("EXP", call, 0, RX_CALL_TIMEOUT, -ETIME);
 		}
 		set_bit(RXRPC_CALL_EV_ABORT, &call->events);
 		goto recheck_state;
net/rxrpc/conn_object.c +1 -1
index b2159dbf5412..660cd9b1a465 100644
@@ -183,7 +183,7 @@ void __rxrpc_disconnect_call(struct rxrpc_connection *conn,
 			chan->last_type = RXRPC_PACKET_TYPE_ABORT;
 			break;
 		default:
-			chan->last_abort = RX_USER_ABORT;
+			chan->last_abort = RX_CALL_DEAD;
 			chan->last_type = RXRPC_PACKET_TYPE_ABORT;
 			break;
 		}
Signature · 1 line
2.35.1
author maintainer
#137 lore raw

PATCH 131/135 afs: Adjust ACK interpretation to try and cope with NAT

In reply to Sasha Levin

From: David Howells <[email protected]>

[ Upstream commit adc9613ff66c26ebaff9814973181ac178beb90b ]

If a client's address changes, say if it is NAT'd, this can disrupt an in progress operation. For most operations, this is not much of a problem, but StoreData can be different as some servers modify the target file as the data comes in, so if a store request is disrupted, the file can get corrupted on the server.

The problem is that the server doesn't recognise packets that come after the change of address as belonging to the original client and will bounce them, either by sending an OUT_OF_SEQUENCE ACK to the apparent new call if the packet number falls within the initial sequence number window of a call or by sending an EXCEEDS_WINDOW ACK if it falls outside and then aborting it. In both cases, firstPacket will be 1 and previousPacket will be 0 in the ACK information.

Fix this by the following means:

(1) If a client call receives an EXCEEDS_WINDOW ACK with firstPacket as 1 and previousPacket as 0, assume this indicates that the server saw the incoming packets from a different peer and thus as a different call. Fail the call with error -ENETRESET.

(2) Also fail the call if a similar OUT_OF_SEQUENCE ACK occurs if the first packet has been hard-ACK'd. If it hasn't been hard-ACK'd, the ACK packet will cause it to get retransmitted, so the call will just be repeated.

(3) Make afs_select_fileserver() treat -ENETRESET as a straight fail of the operation.

(4) Prioritise the error code over things like -ECONNRESET as the server did actually respond.

(5) Make writeback treat -ENETRESET as a retryable error and make it redirty all the pages involved in a write so that the VM will retry.

Note that there is still a circumstance that I can't easily deal with: if the operation is fully received and processed by the server, but the reply is lost due to address change. There's no way to know if the op happened. We can examine the server, but a conflicting change could have been made by a third party - and we can't tell the difference. In such a case, a message like:

    kAFS: vnode modified {100058:146266} b7->b8 YFS.StoreData64 (op=2646a)

will be logged to dmesg on the next op to touch the file and the client will reset the inode state, including invalidating clean parts of the pagecache.

---
 fs/afs/misc.c     |  5 ++++-
 fs/afs/rotate.c   |  4 ++++
 fs/afs/write.c    |  1 +
 net/rxrpc/input.c | 27 +++++++++++++++++++++++++++
 4 files changed, 36 insertions(+), 1 deletion(-)
fs/afs/misc.c +4 -1
index 1d1a8debe472..933e67fcdab1 100644
@@ -163,8 +163,11 @@ void afs_prioritise_error(struct afs_error *e, int error, u32 abort_code)
 		return;
 
 	case -ECONNABORTED:
+		error = afs_abort_to_error(abort_code);
+		fallthrough;
+	case -ENETRESET: /* Responded, but we seem to have changed address */
 		e->responded = true;
-		e->error = afs_abort_to_error(abort_code);
+		e->error = error;
 		return;
 	}
 }
fs/afs/rotate.c +4 -0
index 79e1a5f6701b..a840c3588ebb 100644
@@ -292,6 +292,10 @@ bool afs_select_fileserver(struct afs_operation *op)
 		op->error = error;
 		goto iterate_address;
 
+	case -ENETRESET:
+		pr_warn("kAFS: Peer reset %s (op=%x)\n",
+			op->type ? op->type->name : "???", op->debug_id);
+		fallthrough;
 	case -ECONNRESET:
 		_debug("call reset");
 		op->error = error;
fs/afs/write.c +1 -0
index f447c902318d..07454b1ed240 100644
@@ -638,6 +638,7 @@ static ssize_t afs_write_back_from_locked_folio(struct address_space *mapping,
 	case -EKEYEXPIRED:
 	case -EKEYREJECTED:
 	case -EKEYREVOKED:
+	case -ENETRESET:
 		afs_redirty_pages(wbc, mapping, start, len);
 		mapping_set_error(mapping, ret);
 		break;
net/rxrpc/input.c +27 -0
index dc201363f2c4..67d3eba60dc7 100644
@@ -903,6 +903,33 @@ static void rxrpc_input_ack(struct rxrpc_call *call, struct sk_buff *skb)
 				  rxrpc_propose_ack_respond_to_ack);
 	}
 
+	/* If we get an EXCEEDS_WINDOW ACK from the server, it probably
+	 * indicates that the client address changed due to NAT.  The server
+	 * lost the call because it switched to a different peer.
+	 */
+	if (unlikely(buf.ack.reason == RXRPC_ACK_EXCEEDS_WINDOW) &&
+	    first_soft_ack == 1 &&
+	    prev_pkt == 0 &&
+	    rxrpc_is_client_call(call)) {
+		rxrpc_set_call_completion(call, RXRPC_CALL_REMOTELY_ABORTED,
+					  0, -ENETRESET);
+		return;
+	}
+
+	/* If we get an OUT_OF_SEQUENCE ACK from the server, that can also
+	 * indicate a change of address.  However, we can retransmit the call
+	 * if we still have it buffered to the beginning.
+	 */
+	if (unlikely(buf.ack.reason == RXRPC_ACK_OUT_OF_SEQUENCE) &&
+	    first_soft_ack == 1 &&
+	    prev_pkt == 0 &&
+	    call->tx_hard_ack == 0 &&
+	    rxrpc_is_client_call(call)) {
+		rxrpc_set_call_completion(call, RXRPC_CALL_REMOTELY_ABORTED,
+					  0, -ENETRESET);
+		return;
+	}
+
 	/* Discard any out-of-order or duplicate ACKs (outside lock). */
 	if (!rxrpc_is_ack_valid(call, first_soft_ack, prev_pkt)) {
 		trace_rxrpc_rx_discard_ack(call->debug_id, ack_serial,
Signature · 1 line
2.35.1
author maintainer
#138 lore raw

PATCH 132/135 eth: tg3: silence the GCC 12 array-bounds warning

In reply to Sasha Levin

From: Jakub Kicinski <[email protected]>

[ Upstream commit 9dec850fd7c210a04b4707df8e6c95bfafdd6a4b ]

GCC 12 currently generates a rather inconsistent warning:

drivers/net/ethernet/broadcom/tg3.c:17795:51: warning: array subscript 5 is above array bounds of ‘struct tg3_napi[5]’ [-Warray-bounds]
17795 | struct tg3_napi *tnapi = &tp->napi[i];
| ~~~~~~~~^~~

i is guaranteed < tp->irq_max which in turn is either 1 or 5. There are more loops like this one in the driver, but strangely GCC 12 dislikes only this single one.

Silence this silliness for now.

---
 drivers/net/ethernet/broadcom/Makefile | 5 +++++
 1 file changed, 5 insertions(+)
drivers/net/ethernet/broadcom/Makefile +5 -0
index 0ddfb5b5d53c..2e6c5f258a1f 100644
@@ -17,3 +17,8 @@ obj-$(CONFIG_BGMAC_BCMA) += bgmac-bcma.o bgmac-bcma-mdio.o
 obj-$(CONFIG_BGMAC_PLATFORM) += bgmac-platform.o
 obj-$(CONFIG_SYSTEMPORT) += bcmsysport.o
 obj-$(CONFIG_BNXT) += bnxt/
+
+# FIXME: temporarily silence -Warray-bounds on non W=1+ builds
+ifndef KBUILD_EXTRA_WARN
+CFLAGS_tg3.o += -Wno-array-bounds
+endif
Signature · 1 line
2.35.1
author maintainer
#139 lore raw

PATCH 133/135 char: tpm: cr50_i2c: Suppress duplicated error message in .remove()

In reply to Sasha Levin

From: Uwe Kleine-König <[email protected]>

[ Upstream commit e0687fe958f763f1790f22ed5483025b7624e744 ]

Returning an error value in an i2c remove callback results in an error message being emitted by the i2c core, but otherwise it doesn't make a difference. The device goes away anyhow and the devm cleanups are called.

As tpm_cr50_i2c_remove() emits an error message already and the additional error message by the i2c core doesn't add any useful information, change the return value to zero to suppress this error message.

Note that if i2c_clientdata is NULL, there is something really fishy. Assuming no memory corruption happened (then all bets are lost anyhow), tpm_cr50_i2c_remove() is only called after tpm_cr50_i2c_probe() returned successfully. So there was a tpm chip registered before and after tpm_cr50_i2c_remove() its privdata is freed but the associated character device isn't removed. If after that happened userspace accesses the character device it's likely that the freed memory is accessed. For that reason the warning message is made a bit more frightening.

---
 drivers/char/tpm/tpm_tis_i2c_cr50.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/char/tpm/tpm_tis_i2c_cr50.c +2 -2
index f6c0affbb456..bf608b6af339 100644
@@ -768,8 +768,8 @@ static int tpm_cr50_i2c_remove(struct i2c_client *client)
 	struct device *dev = &client->dev;
 
 	if (!chip) {
-		dev_err(dev, "Could not get client data at remove\n");
-		return -ENODEV;
+		dev_crit(dev, "Could not get client data at remove, memory corruption ahead\n");
+		return 0;
 	}
 
 	tpm_chip_unregister(chip);
Signature · 1 line
2.35.1
author maintainer
#140 lore raw

PATCH 134/135 selftests/bpf: fix btf_dump/btf_dump due to recent clang change

In reply to Sasha Levin

From: Yonghong Song <[email protected]>

[ Upstream commit 4050764cbaa25760aab40857f723393c07898474 ]

Latest llvm-project upstream had a change of behavior related to qualifiers on function return type ([1]). This caused selftests btf_dump/btf_dump failure. The following example shows what changed.

  $ cat t.c
  typedef const char * const (* const (* const fn_ptr_arr2_t[5])())(char * (*)(int));
  struct t {
    int a;
    fn_ptr_arr2_t l;
  };
  int foo(struct t *arg) {
    return arg->a;
  }

Compiled with latest upstream llvm15,

  $ clang -O2 -g -target bpf -S -emit-llvm t.c
The related generated debuginfo IR looks like:
  !16 = !DIDerivedType(tag: DW_TAG_typedef, name: "fn_ptr_arr2_t", file: !1, line: 1, baseType: !17)
  !17 = !DICompositeType(tag: DW_TAG_array_type, baseType: !18, size: 320, elements: !32)
  !18 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !19)
  !19 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !20, size: 64)
  !20 = !DISubroutineType(types: !21)
  !21 = !{!22, null}
  !22 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !23, size: 64)
  !23 = !DISubroutineType(types: !24)
  !24 = !{!25, !28}
  !25 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !26, size: 64)
  !26 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !27)
  !27 = !DIBasicType(name: "char", size: 8, encoding: DW_ATE_signed_char)
You can see two intermediate const qualifier to pointer are dropped in debuginfo IR.

With llvm14, we have following debuginfo IR:
!16 = !DIDerivedType(tag: DW_TAG_typedef, name: "fn_ptr_arr2_t", file: !1, line: 1, baseType: !17) !17 = !DICompositeType(tag: DW_TAG_array_type, baseType: !18, size: 320, elements: !34) !18 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !19)
!19 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !20, size: 64)
!20 = !DISubroutineType(types: !21)
!21 = !{!22, null}
!22 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !23)
!23 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !24, size: 64)
!24 = !DISubroutineType(types: !25)
!25 = !{!26, !30}
!26 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !27)
!27 = !DIDerivedType(tag: DW_TAG_pointer_type, baseType: !28, size: 64)
!28 = !DIDerivedType(tag: DW_TAG_const_type, baseType: !29)
!29 = !DIBasicType(name: "char", size: 8, encoding: DW_ATE_signed_char)
All const qualifiers are preserved.

To adapt the selftest to both old and new llvm, this patch removed the intermediate const qualifier in const-to-ptr types, to make the test succeed again.

[1] https://reviews.llvm.org/D125919

---
 tools/testing/selftests/bpf/progs/btf_dump_test_case_syntax.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/bpf/progs/btf_dump_test_case_syntax.c +1 -1
index 1c7105fcae3c..4ee4748133fe 100644
@@ -94,7 +94,7 @@ typedef void (* (*signal_t)(int, void (*)(int)))(int);
 
 typedef char * (*fn_ptr_arr1_t[10])(int **);
 
-typedef char * (* const (* const fn_ptr_arr2_t[5])())(char * (*)(int));
+typedef char * (* (* const fn_ptr_arr2_t[5])())(char * (*)(int));
 
 struct struct_w_typedefs {
 	int_t a;
Signature · 1 line
2.35.1
author maintainer
#141 lore raw

PATCH 135/135 gfs2: use i_lock spin_lock for inode qadata

In reply to Sasha Levin

From: Bob Peterson <[email protected]>

[ Upstream commit 5fcff61eea9efd1f4b60e89d2d686b5feaea100f ]

Before this patch, functions gfs2_qa_get and _put used the i_rw_mutex to prevent simultaneous access to its i_qadata. But i_rw_mutex is now used for many other things, including iomap_begin and end, which causes a conflict according to lockdep. We cannot just remove the lock since simultaneous opens (gfs2_open -> gfs2_open_common -> gfs2_qa_get) can then stomp on each others values for i_qadata.

This patch solves the conflict by using the i_lock spin_lock in the inode to prevent simultaneous access.

---
 fs/gfs2/quota.c | 32 ++++++++++++++++++++------------
 1 file changed, 20 insertions(+), 12 deletions(-)
fs/gfs2/quota.c +20 -12
index be0997e24d60..dc77080a82bb 100644
@@ -531,34 +531,42 @@ static void qdsb_put(struct gfs2_quota_data *qd)
  */
 int gfs2_qa_get(struct gfs2_inode *ip)
 {
-	int error = 0;
 	struct gfs2_sbd *sdp = GFS2_SB(&ip->i_inode);
+	struct inode *inode = &ip->i_inode;
 
 	if (sdp->sd_args.ar_quota == GFS2_QUOTA_OFF)
 		return 0;
 
-	down_write(&ip->i_rw_mutex);
+	spin_lock(&inode->i_lock);
 	if (ip->i_qadata == NULL) {
-		ip->i_qadata = kmem_cache_zalloc(gfs2_qadata_cachep, GFP_NOFS);
-		if (!ip->i_qadata) {
-			error = -ENOMEM;
-			goto out;
-		}
+		struct gfs2_qadata *tmp;
+
+		spin_unlock(&inode->i_lock);
+		tmp = kmem_cache_zalloc(gfs2_qadata_cachep, GFP_NOFS);
+		if (!tmp)
+			return -ENOMEM;
+
+		spin_lock(&inode->i_lock);
+		if (ip->i_qadata == NULL)
+			ip->i_qadata = tmp;
+		else
+			kmem_cache_free(gfs2_qadata_cachep, tmp);
 	}
 	ip->i_qadata->qa_ref++;
-out:
-	up_write(&ip->i_rw_mutex);
-	return error;
+	spin_unlock(&inode->i_lock);
+	return 0;
 }
 
 void gfs2_qa_put(struct gfs2_inode *ip)
 {
-	down_write(&ip->i_rw_mutex);
+	struct inode *inode = &ip->i_inode;
+
+	spin_lock(&inode->i_lock);
 	if (ip->i_qadata && --ip->i_qadata->qa_ref == 0) {
 		kmem_cache_free(gfs2_qadata_cachep, ip->i_qadata);
 		ip->i_qadata = NULL;
 	}
-	up_write(&ip->i_rw_mutex);
+	spin_unlock(&inode->i_lock);
 }
 
 int gfs2_quota_hold(struct gfs2_inode *ip, kuid_t uid, kgid_t gid)
Signature · 1 line
2.35.1