iio: adc: meson_saradc: Don't attach managed resource to IIO device object
Subsystems (2)
PATCH v3 1/6 iio: adc: meson_saradc: Don't attach managed resource to IIO device object
It feels wrong and actually inconsistent to attach managed resources to the IIO device object, which is child of the physical device object. The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
---
v3: new fix-patch
drivers/iio/adc/meson_saradc.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)
drivers/iio/adc/meson_saradc.c +5 -7
@@ -650,11 +650,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, void __iomem *base) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;struct clk_init_data init;const char *clk_parents[1 ]; - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_div" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_div" ,dev_name (dev));if (!init.name)return -ENOMEM ;
@@ -670,13 +670,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_div.hw.init = &init; priv->clk_div.flags =0 ; - priv->adc_div_clk =devm_clk_register (&indio_dev->dev, - &priv->clk_div.hw); + priv->adc_div_clk =devm_clk_register (dev, &priv->clk_div.hw);if (WARN_ON (IS_ERR (priv->adc_div_clk)))return PTR_ERR (priv->adc_div_clk); - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_en" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_en" ,dev_name (dev));if (!init.name)return -ENOMEM ;
@@ -690,7 +688,7 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_gate.bit_idx =__ffs (MESON_SAR_ADC_REG3_CLK_EN ); priv->clk_gate.hw.init = &init; - priv->adc_clk =devm_clk_register (&indio_dev->dev, &priv->clk_gate.hw); + priv->adc_clk =devm_clk_register (dev, &priv->clk_gate.hw);if (WARN_ON (IS_ERR (priv->adc_clk)))return PTR_ERR (priv->adc_clk);
Signature · 1 line
2.35.1
PATCH v3 2/6 iio: adc: meson_saradc: Align messages to be with physical device prefix
Align messages to be printed with the physical device prefix as it's done everywhere else in this driver.
---
v3: new patch (inspired by previous change)
drivers/iio/adc/meson_saradc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/iio/adc/meson_saradc.c +3 -4
@@ -345,6 +345,7 @@ static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev, int *val) { struct meson_sar_adc_priv *priv = iio_priv(indio_dev); + struct device *dev = indio_dev->dev.parent; int regval, fifo_chan, fifo_val, count; if (!wait_for_completion_timeout(&priv->done,
@@ -353,16 +354,14 @@ static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev, count =meson_sar_adc_get_fifo_count (indio_dev);if (count !=1 ) { -dev_err (&indio_dev->dev, -"ADC FIFO has %d element(s) instead of one\n" , count); +dev_err (dev,"ADC FIFO has %d element(s) instead of one\n" , count);return -EINVAL ; }regmap_read (priv->regmap,MESON_SAR_ADC_FIFO_RD , ®val); fifo_chan =FIELD_GET (MESON_SAR_ADC_FIFO_RD_CHAN_ID_MASK , regval);if (fifo_chan != chan->address) { -dev_err (&indio_dev->dev, -"ADC FIFO entry belongs to channel %d instead of %lu\n" , +dev_err (dev,"ADC FIFO entry belongs to channel %d instead of %lu\n" , fifo_chan, chan->address);return -EINVAL ; }
Signature · 1 line
2.35.1
Jonathan Cameron
maintainerRe: [PATCH v3 2/6] iio: adc: meson_saradc: Align messages to be with physical device prefix
Quoted 4 lines · On Fri, 3 Jun 2022 13:00:00 +0300 Andy Shevchenko…
Align messages to be printed with the physical device prefix as it's done everywhere else in this driver.
Signed-off-by Andy Shevchenko <[email protected]>
Here I'm fine with the use of the parent as can only happen after all the setup is done, so it's obvious the parent will be assigned (some might argue it is obvious in the previous patch, but I had to check as I couldn't remember when we set it :)
Anyhow, LGTM.
Quoted 36 lines
---
v3: new patch (inspired by previous change)drivers/iio/adc/meson_saradc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)drivers/iio/adc/meson_saradc.c +3
-4@@ -345,6 +345,7 @@ static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev, int *val) { struct meson_sar_adc_priv *priv = iio_priv(indio_dev); + struct device *dev = indio_dev->dev.parent; int regval, fifo_chan, fifo_val, count; if (!wait_for_completion_timeout(&priv->done,@@ -353,16 +354,14 @@ static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev, count =meson_sar_adc_get_fifo_count (indio_dev);if (count !=1 ) { -dev_err (&indio_dev->dev, -"ADC FIFO has %d element(s) instead of one\n" , count); +dev_err (dev,"ADC FIFO has %d element(s) instead of one\n" , count);return -EINVAL ; }regmap_read (priv->regmap,MESON_SAR_ADC_FIFO_RD , ®val); fifo_chan =FIELD_GET (MESON_SAR_ADC_FIFO_RD_CHAN_ID_MASK , regval);if (fifo_chan != chan->address) { -dev_err (&indio_dev->dev, -"ADC FIFO entry belongs to channel %d instead of %lu\n" , +dev_err (dev,"ADC FIFO entry belongs to channel %d instead of %lu\n" , fifo_chan, chan->address);return -EINVAL ; }
Re: [PATCH v3 2/6] iio: adc: meson_saradc: Align messages to be with physical device prefix
Quoted 6 lines · Jonathan Cameron
Quoted 2 lines · On Fri, 3 Jun 2022 13:00:00 +0300 Andy Shevchenko…
Align messages to be printed with the physical device prefix as it's done everywhere else in this driver.
Quoted 6 lines
Here I'm fine with the use of the parent as can only happen after all the setup is done, so it's obvious the parent will be assigned (some might argue it is obvious in the previous patch, but I had to check as I couldn't remember when we set it :)
Anyhow, LGTM.
Thanks!
Quoted 1 line
Quoted 1 line
v3: new patch (inspired by previous change)
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH v3 2/6] iio: adc: meson_saradc: Align messages to be with physical device prefix
In reply to Andy ShevchenkoQuoted 5 lines · Andy Shevchenko
Align messages to be printed with the physical device prefix as it's done everywhere else in this driver.
Signed-off-by Andy Shevchenko <[email protected]>
PATCH v3 3/6 iio: adc: meson_saradc: Convert to use dev_err_probe()
In reply to Andy ShevchenkoIt's fine to call dev_err_probe() in ->probe() when error code is known. Convert the driver to use dev_err_probe().
---
v3: rebased on top of previous changes
drivers/iio/adc/meson_saradc.c | 52 +++++++++++++--------------------- 1 file changed, 19 insertions(+), 33 deletions(-)
drivers/iio/adc/meson_saradc.c +19 -33
@@ -698,6 +698,7 @@ static int meson_sar_adc_temp_sensor_init(struct iio_dev *indio_dev) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev);u8 *buf, trimming_bits, trimming_mask, upper_adc_val; +struct device *dev = indio_dev->dev.parent;struct nvmem_cell *temperature_calib;size_t read_len;int ret;
@@ -714,30 +715,23 @@ static int meson_sar_adc_temp_sensor_init(struct iio_dev *indio_dev)if (ret == -ENODEV )return 0 ; -return dev_err_probe (indio_dev->dev.parent, ret, -"failed to get temperature_calib cell\n" ); +return dev_err_probe (dev, ret,"failed to get temperature_calib cell\n" ); } priv->tsc_regmap =syscon_regmap_lookup_by_phandle (indio_dev->dev.parent->of_node,"amlogic,hhi-sysctrl" ); -if (IS_ERR (priv->tsc_regmap)) { -dev_err (indio_dev->dev.parent, -"failed to get amlogic,hhi-sysctrl regmap\n" ); -return PTR_ERR (priv->tsc_regmap); - } +if (IS_ERR (priv->tsc_regmap)) +return dev_err_probe (dev,PTR_ERR (priv->tsc_regmap), +"failed to get amlogic,hhi-sysctrl regmap\n" ); read_len =MESON_SAR_ADC_EFUSE_BYTES ; buf =nvmem_cell_read (temperature_calib, &read_len); -if (IS_ERR (buf)) { -dev_err (indio_dev->dev.parent, -"failed to read temperature_calib cell\n" ); -return PTR_ERR (buf); - }else if (read_len !=MESON_SAR_ADC_EFUSE_BYTES ) { +if (IS_ERR (buf)) +return dev_err_probe (dev,PTR_ERR (buf),"failed to read temperature_calib cell\n" ); +if (read_len !=MESON_SAR_ADC_EFUSE_BYTES ) {kfree (buf); -dev_err (indio_dev->dev.parent, -"invalid read size of temperature_calib cell\n" ); -return -EINVAL ; +return dev_err_probe (dev, -EINVAL ,"invalid read size of temperature_calib cell\n" ); } trimming_bits = priv->param->temperature_trimming_bits;
@@ -762,6 +756,7 @@ static int meson_sar_adc_temp_sensor_init(struct iio_dev *indio_dev)static int meson_sar_adc_init (struct iio_dev *indio_dev) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;int regval, i, ret;/*
@@ -885,18 +880,12 @@ static int meson_sar_adc_init(struct iio_dev *indio_dev) } ret =clk_set_parent (priv->adc_sel_clk, priv->clkin); -if (ret) { -dev_err (indio_dev->dev.parent, -"failed to set adc parent to clkin\n" ); -return ret; - } +if (ret) +return dev_err_probe (dev, ret,"failed to set adc parent to clkin\n" ); ret =clk_set_rate (priv->adc_clk, priv->param->clock_rate); -if (ret) { -dev_err (indio_dev->dev.parent, -"failed to set adc clock rate\n" ); -return ret; - } +if (ret) +return dev_err_probe (dev, ret,"failed to set adc clock rate\n" );return 0 ; }
@@ -1183,24 +1172,21 @@ static int meson_sar_adc_probe(struct platform_device *pdev) {const struct meson_sar_adc_data *match_data;struct meson_sar_adc_priv *priv; +struct device *dev = &pdev->dev;struct iio_dev *indio_dev;void __iomem *base;int irq, ret; indio_dev =devm_iio_device_alloc (&pdev->dev,sizeof (*priv)); -if (!indio_dev) { -dev_err (&pdev->dev,"failed allocating iio device\n" ); -return -ENOMEM ; - } +if (!indio_dev) +return dev_err_probe (dev, -ENOMEM ,"failed allocating iio device\n" ); priv =iio_priv (indio_dev);init_completion (&priv->done); match_data =of_device_get_match_data (&pdev->dev); -if (!match_data) { -dev_err (&pdev->dev,"failed to get match data\n" ); -return -ENODEV ; - } +if (!match_data) +return dev_err_probe (dev, -ENODEV ,"failed to get match data\n" ); priv->param = match_data->param;
Signature · 1 line
2.35.1
Re: [PATCH v3 3/6] iio: adc: meson_saradc: Convert to use dev_err_probe()
Quoted 5 lines · Andy Shevchenko
It's fine to call
dev_err_probe()in ->probe() when error code is known. Convert the driver to usedev_err_probe().Signed-off-by Andy Shevchenko <[email protected]>
PATCH v3 4/6 iio: adc: meson_saradc: Use devm_clk_get_optional()
In reply to Andy ShevchenkoReplace open coded variants of devm_clk_get_optional().
---
v3: no changes
drivers/iio/adc/meson_saradc.c | 22 ++++++---------------- 1 file changed, 6 insertions(+), 16 deletions(-)
drivers/iio/adc/meson_saradc.c +6 -16
@@ -1222,23 +1222,13 @@ static int meson_sar_adc_probe(struct platform_device *pdev)return dev_err_probe (&pdev->dev,PTR_ERR (priv->core_clk),"failed to get core clk\n" ); - priv->adc_clk =devm_clk_get (&pdev->dev,"adc_clk" ); -if (IS_ERR (priv->adc_clk)) { -if (PTR_ERR (priv->adc_clk) == -ENOENT ) - priv->adc_clk =NULL ; -else -return dev_err_probe (&pdev->dev,PTR_ERR (priv->adc_clk), -"failed to get adc clk\n" ); - } + priv->adc_clk =devm_clk_get_optional (dev,"adc_clk" ); +if (IS_ERR (priv->adc_clk)) +return dev_err_probe (dev,PTR_ERR (priv->adc_clk),"failed to get adc clk\n" ); - priv->adc_sel_clk =devm_clk_get (&pdev->dev,"adc_sel" ); -if (IS_ERR (priv->adc_sel_clk)) { -if (PTR_ERR (priv->adc_sel_clk) == -ENOENT ) - priv->adc_sel_clk =NULL ; -else -return dev_err_probe (&pdev->dev,PTR_ERR (priv->adc_sel_clk), -"failed to get adc_sel clk\n" ); - } + priv->adc_sel_clk =devm_clk_get_optional (dev,"adc_sel" ); +if (IS_ERR (priv->adc_sel_clk)) +return dev_err_probe (dev,PTR_ERR (priv->adc_sel_clk),"failed to get adc_sel clk\n" );/* on pre-GXBB SoCs the SAR ADC itself provides the ADC clock: */ if (!priv->adc_clk) {
Signature · 1 line
2.35.1
PATCH v3 5/6 iio: adc: meson_saradc: Use temporary variable for struct device
In reply to Andy ShevchenkoUse temporary variable for struct device to make code neater.
---
v3: rebased on top of previous changes
drivers/iio/adc/meson_saradc.c | 53 ++++++++++++++-------------------- 1 file changed, 22 insertions(+), 31 deletions(-)
drivers/iio/adc/meson_saradc.c +22 -31
@@ -549,6 +549,7 @@ static int meson_sar_adc_get_sample(struct iio_dev *indio_dev, int *val) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;int ret;if (chan->type ==IIO_TEMP && !priv->temperature_sensor_calibrated)
@@ -572,8 +573,7 @@ static int meson_sar_adc_get_sample(struct iio_dev *indio_dev,meson_sar_adc_unlock (indio_dev);if (ret) { -dev_warn (indio_dev->dev.parent, -"failed to read sample for channel %lu: %d\n" , +dev_warn (dev,"failed to read sample for channel %lu: %d\n" , chan->address, ret);return ret; }
@@ -586,6 +586,7 @@ static int meson_sar_adc_iio_info_read_raw(struct iio_dev *indio_dev, int *val, int *val2, long mask) { struct meson_sar_adc_priv *priv = iio_priv(indio_dev); +struct device *dev = indio_dev->dev.parent;int ret;switch (mask) {
@@ -602,9 +603,7 @@ static int meson_sar_adc_iio_info_read_raw(struct iio_dev *indio_dev,if (chan->type ==IIO_VOLTAGE ) { ret =regulator_get_voltage (priv->vref);if (ret <0 ) { -dev_err (indio_dev->dev.parent, -"failed to get vref voltage: %d\n" , - ret); +dev_err (dev,"failed to get vref voltage: %d\n" , ret);return ret; }
@@ -703,8 +702,7 @@ static int meson_sar_adc_temp_sensor_init(struct iio_dev *indio_dev)size_t read_len;int ret; - temperature_calib =devm_nvmem_cell_get (indio_dev->dev.parent, -"temperature_calib" ); + temperature_calib =devm_nvmem_cell_get (dev,"temperature_calib" );if (IS_ERR (temperature_calib)) { ret =PTR_ERR (temperature_calib);
@@ -718,9 +716,7 @@ static int meson_sar_adc_temp_sensor_init(struct iio_dev *indio_dev)return dev_err_probe (dev, ret,"failed to get temperature_calib cell\n" ); } - priv->tsc_regmap = -syscon_regmap_lookup_by_phandle (indio_dev->dev.parent->of_node, -"amlogic,hhi-sysctrl" ); + priv->tsc_regmap =syscon_regmap_lookup_by_phandle (dev->of_node,"amlogic,hhi-sysctrl" );if (IS_ERR (priv->tsc_regmap))return dev_err_probe (dev,PTR_ERR (priv->tsc_regmap),"failed to get amlogic,hhi-sysctrl regmap\n" );
@@ -908,6 +904,7 @@ static void meson_sar_adc_set_bandgap(struct iio_dev *indio_dev, bool on_off)static int meson_sar_adc_hw_enable (struct iio_dev *indio_dev) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;int ret;u32 regval;
@@ -917,14 +914,13 @@ static int meson_sar_adc_hw_enable(struct iio_dev *indio_dev) ret =regulator_enable (priv->vref);if (ret <0 ) { -dev_err (indio_dev->dev.parent, -"failed to enable vref regulator\n" ); +dev_err (dev,"failed to enable vref regulator\n" ); goto err_vref; } ret =clk_prepare_enable (priv->core_clk);if (ret) { -dev_err (indio_dev->dev.parent,"failed to enable core clk\n" ); +dev_err (dev,"failed to enable core clk\n" ); goto err_core_clk; }
@@ -942,7 +938,7 @@ static int meson_sar_adc_hw_enable(struct iio_dev *indio_dev) ret =clk_prepare_enable (priv->adc_clk);if (ret) { -dev_err (indio_dev->dev.parent,"failed to enable adc clk\n" ); +dev_err (dev,"failed to enable adc clk\n" ); goto err_adc_clk; }
@@ -1177,14 +1173,14 @@ static int meson_sar_adc_probe(struct platform_device *pdev)void __iomem *base;int irq, ret; - indio_dev =devm_iio_device_alloc (&pdev->dev,sizeof (*priv)); + indio_dev =devm_iio_device_alloc (dev,sizeof (*priv));if (!indio_dev)return dev_err_probe (dev, -ENOMEM ,"failed allocating iio device\n" ); priv =iio_priv (indio_dev);init_completion (&priv->done); - match_data =of_device_get_match_data (&pdev->dev); + match_data =of_device_get_match_data (dev);if (!match_data)return dev_err_probe (dev, -ENODEV ,"failed to get match data\n" );
@@ -1198,29 +1194,25 @@ static int meson_sar_adc_probe(struct platform_device *pdev)if (IS_ERR (base))return PTR_ERR (base); - priv->regmap =devm_regmap_init_mmio (&pdev->dev, base, - priv->param->regmap_config); + priv->regmap =devm_regmap_init_mmio (dev, base, priv->param->regmap_config);if (IS_ERR (priv->regmap))return PTR_ERR (priv->regmap); - irq =irq_of_parse_and_map (pdev->dev.of_node,0 ); + irq =irq_of_parse_and_map (dev->of_node,0 );if (!irq)return -EINVAL ; - ret =devm_request_irq (&pdev->dev, irq, meson_sar_adc_irq,IRQF_SHARED , -dev_name (&pdev->dev), indio_dev); + ret =devm_request_irq (dev, irq, meson_sar_adc_irq,IRQF_SHARED ,dev_name (dev), indio_dev);if (ret)return ret; - priv->clkin =devm_clk_get (&pdev->dev,"clkin" ); + priv->clkin =devm_clk_get (dev,"clkin" );if (IS_ERR (priv->clkin)) -return dev_err_probe (&pdev->dev,PTR_ERR (priv->clkin), -"failed to get clkin\n" ); +return dev_err_probe (dev,PTR_ERR (priv->clkin),"failed to get clkin\n" ); - priv->core_clk =devm_clk_get (&pdev->dev,"core" ); + priv->core_clk =devm_clk_get (dev,"core" );if (IS_ERR (priv->core_clk)) -return dev_err_probe (&pdev->dev,PTR_ERR (priv->core_clk), -"failed to get core clk\n" ); +return dev_err_probe (dev,PTR_ERR (priv->core_clk),"failed to get core clk\n" ); priv->adc_clk =devm_clk_get_optional (dev,"adc_clk" );if (IS_ERR (priv->adc_clk))
@@ -1237,10 +1229,9 @@ static int meson_sar_adc_probe(struct platform_device *pdev)return ret; } - priv->vref =devm_regulator_get (&pdev->dev,"vref" ); + priv->vref =devm_regulator_get (dev,"vref" );if (IS_ERR (priv->vref)) -return dev_err_probe (&pdev->dev,PTR_ERR (priv->vref), -"failed to get vref regulator\n" ); +return dev_err_probe (dev,PTR_ERR (priv->vref),"failed to get vref regulator\n" ); priv->calibscale =MILLION ;
@@ -1270,7 +1261,7 @@ static int meson_sar_adc_probe(struct platform_device *pdev) ret =meson_sar_adc_calib (indio_dev);if (ret) -dev_warn (&pdev->dev,"calibration failed\n" ); +dev_warn (dev,"calibration failed\n" );platform_set_drvdata (pdev, indio_dev);
Signature · 1 line
2.35.1
Re: [PATCH v3 5/6] iio: adc: meson_saradc: Use temporary variable for struct device
Quoted 4 lines · Andy Shevchenko
Use temporary variable for struct device to make code neater.
Signed-off-by Andy Shevchenko <[email protected]>
RFC PATCH v3 6/6 iio: adc: meson_saradc: Use regmap_read_poll_timeout() for busy wait
In reply to Andy ShevchenkoSimplify busy wait stages by using regmap_read_poll_timeout().
---
v3: new patch, but RFC, not always the read_poll_timeout() can be used, would
be nice to have it tested.
drivers/iio/adc/meson_saradc.c | 31 +++++++++++++------------------ 1 file changed, 13 insertions(+), 18 deletions(-)
drivers/iio/adc/meson_saradc.c +13 -18
@@ -322,22 +322,17 @@ static int meson_sar_adc_calib_val(struct iio_dev *indio_dev, int val)static int meson_sar_adc_wait_busy_clear (struct iio_dev *indio_dev) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); -int regval, timeout =10000 ; +int val;/* * NOTE: we need a small delay before reading the status, otherwise * the sample engine may not have started internally (which would * seem to us that sampling is already finished). */ -do { -udelay (1 ); -regmap_read (priv->regmap,MESON_SAR_ADC_REG0 , ®val); - }while (FIELD_GET (MESON_SAR_ADC_REG0_BUSY_MASK , regval) && timeout--); - -if (timeout <0 ) -return -ETIMEDOUT ; - -return 0 ; +udelay (1 ); +return regmap_read_poll_timeout_atomic (priv->regmap,MESON_SAR_ADC_REG0 , val, + !FIELD_GET (MESON_SAR_ADC_REG0_BUSY_MASK , val), +1 ,10000 ); } static int meson_sar_adc_read_raw_sample(struct iio_dev *indio_dev,
@@ -489,7 +484,7 @@ static void meson_sar_adc_stop_sample_engine(struct iio_dev *indio_dev)static int meson_sar_adc_lock (struct iio_dev *indio_dev) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); -int val, timeout =10000 ; +int val, ret;mutex_lock (&indio_dev->mlock);
@@ -499,18 +494,18 @@ static int meson_sar_adc_lock(struct iio_dev *indio_dev)MESON_SAR_ADC_DELAY_KERNEL_BUSY , MESON_SAR_ADC_DELAY_KERNEL_BUSY); +udelay (1 ); +/* * wait until BL30 releases it's lock (so we can use the SAR * ADC) */ -do { -udelay (1 ); -regmap_read (priv->regmap,MESON_SAR_ADC_DELAY , &val); - }while (val &MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--); - -if (timeout <0 ) { + ret =regmap_read_poll_timeout_atomic (priv->regmap,MESON_SAR_ADC_DELAY , val, + !(val &MESON_SAR_ADC_DELAY_BL30_BUSY ), +1 ,10000 ); +if (ret) {mutex_unlock (&indio_dev->mlock); -return -ETIMEDOUT ; +return ret; } }
Signature · 1 line
2.35.1
Re: [RFC PATCH v3 6/6] iio: adc: meson_saradc: Use regmap_read_poll_timeout() for busy wait
Quoted 4 lines · Andy Shevchenko
Simplify busy wait stages by using
regmap_read_poll_timeout().Signed-off-by Andy Shevchenko <[email protected]>
Quoted 2 lines
v3: new patch, but RFC, not always the
read_poll_timeout()can be used, would
be nice to have it tested.
and also:
Re: [RFC PATCH v3 6/6] iio: adc: meson_saradc: Use regmap_read_poll_timeout() for busy wait
Quoted 5 lines · Martin Blumenstingl
Quoted 3 lines · Andy Shevchenko
Simplify busy wait stages by using
regmap_read_poll_timeout().
Quoted 7 lines
Quoted 1 line
Signed-off-by Andy Shevchenko <[email protected]>Reviewed-by Martin Blumenstingl <[email protected]>Quoted 2 lines
v3: new patch, but RFC, not always the
read_poll_timeout()can be used, would
be nice to have it tested.and also:
Thanks for testing!
Signature · 2 lines
With Best Regards, Andy Shevchenko
Jonathan Cameron
maintainerQuoted 9 lines · On Fri, 3 Jun 2022 12:59:59 +0300 Andy Shevchenko…
It feels wrong and actually inconsistent to attach managed resources to the IIO device object, which is child of the physical device object. The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
Fixes 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")Suggested-by Lars-Peter Clausen <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>
Hi Andy,
This has come up a few times in the past (and we elected to not clean it up at the time, though it wasn't a decision to never do so!)
It would definitely be wrong if we had another driver binding against the resulting created device (funnily enough I reported a bug on a driver doing just that earlier this week), but in this case it's harmless because the the tear down will occur with a put_device() ultimately calling device_release() and devres_release_all()
https://elixir.bootlin.com/linux/latest/source/drivers/base/core.c#L2211
Has a comment that covers this case (more or less).
"
* Some platform devices are driven without driver attached
* and managed resources may have been acquired. Make sure
* all resources are released.
"
Now, I definitely agree with your statement that it's a bit inconsistent to do this, just not the fixes tag.
One other suggestion below.
Quoted 10 lines
---
v3: new fix-patchdrivers/iio/adc/meson_saradc.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)drivers/iio/adc/meson_saradc.c +0
-0
drivers/iio/adc/meson_saradc.c static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, · line 653
Quoted 4 lines
drivers/iio/adc/meson_saradc.c +1
-0@@ -650,11 +650,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, void __iomem *base) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;
I'd slightly prefer the device was passed in explicitly to this function rather than using the parent assignment which feels a little fragile.
Quoted 34 lines
drivers/iio/adc/meson_saradc.c +4
-7struct clk_init_data init;const char *clk_parents[1 ]; - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_div" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_div" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -670,13 +670,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_div.hw.init = &init; priv->clk_div.flags =0 ; - priv->adc_div_clk =devm_clk_register (&indio_dev->dev, - &priv->clk_div.hw); + priv->adc_div_clk =devm_clk_register (dev, &priv->clk_div.hw);if (WARN_ON (IS_ERR (priv->adc_div_clk)))return PTR_ERR (priv->adc_div_clk); - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_en" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_en" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -690,7 +688,7 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_gate.bit_idx =__ffs (MESON_SAR_ADC_REG3_CLK_EN ); priv->clk_gate.hw.init = &init; - priv->adc_clk =devm_clk_register (&indio_dev->dev, &priv->clk_gate.hw); + priv->adc_clk =devm_clk_register (dev, &priv->clk_gate.hw);if (WARN_ON (IS_ERR (priv->adc_clk)))return PTR_ERR (priv->adc_clk);
Jonathan Cameron
maintainerQuoted 43 lines · On Fri, 3 Jun 2022 17:06:12 +0100 Jonathan Cameron <[email protected]> wrote:
Quoted 9 lines · On Fri, 3 Jun 2022 12:59:59 +0300 Andy Shevchenko…
It feels wrong and actually inconsistent to attach managed resources to the IIO device object, which is child of the physical device object. The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
Fixes 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")Suggested-by Lars-Peter Clausen <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>Hi Andy,
This has come up a few times in the past (and we elected to not clean it up at the time, though it wasn't a decision to never do so!)
It would definitely be wrong if we had another driver binding against the resulting created device (funnily enough I reported a bug on a driver doing just that earlier this week), but in this case it's harmless because the the tear down will occur with a
put_device()ultimately callingdevice_release()anddevres_release_all()https://elixir.bootlin.com/linux/latest/source/drivers/base/core.c#L2211
Has a comment that covers this case (more or less).
"
* Some platform devices are driven without driver attached
* and managed resources may have been acquired. Make sure
* all resources are released.
"Now, I definitely agree with your statement that it's a bit inconsistent to do this, just not the fixes tag.
One other suggestion below.
Quoted 5 lines
---
v3: new fix-patchdrivers/iio/adc/meson_saradc.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)
Quoted 12 lines
drivers/iio/adc/meson_saradc.c static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, · line 653
Quoted 9 lines
drivers/iio/adc/meson_saradc.c +1
-0@@ -650,11 +650,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, void __iomem *base) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;I'd slightly prefer the device was passed in explicitly to this function rather than using the parent assignment which feels a little fragile.
Meh, ignore this. I see from one of the later patches, the driver is already making the assumption this is set in other calls, so we aren't making anything worse with this change.
Jonathan
Quoted 37 lines
Quoted 36 lines
drivers/iio/adc/meson_saradc.c +4
-7struct clk_init_data init;const char *clk_parents[1 ]; - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_div" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_div" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -670,13 +670,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_div.hw.init = &init; priv->clk_div.flags =0 ; - priv->adc_div_clk =devm_clk_register (&indio_dev->dev, - &priv->clk_div.hw); + priv->adc_div_clk =devm_clk_register (dev, &priv->clk_div.hw);if (WARN_ON (IS_ERR (priv->adc_div_clk)))return PTR_ERR (priv->adc_div_clk); - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_en" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_en" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -690,7 +688,7 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_gate.bit_idx =__ffs (MESON_SAR_ADC_REG3_CLK_EN ); priv->clk_gate.hw.init = &init; - priv->adc_clk =devm_clk_register (&indio_dev->dev, &priv->clk_gate.hw); + priv->adc_clk =devm_clk_register (dev, &priv->clk_gate.hw);if (WARN_ON (IS_ERR (priv->adc_clk)))return PTR_ERR (priv->adc_clk);
Jonathan Cameron
maintainerQuoted 35 lines · On Fri, 3 Jun 2022 17:23:07 +0100 Jonathan Cameron <[email protected]> wrote:
Quoted 32 lines · On Fri, 3 Jun 2022 17:06:12 +0100 Jonathan Cameron <[email protected]> wrote:
Quoted 9 lines · On Fri, 3 Jun 2022 12:59:59 +0300 Andy Shevchenko…
It feels wrong and actually inconsistent to attach managed resources to the IIO device object, which is child of the physical device object. The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
Fixes 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")Suggested-by Lars-Peter Clausen <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>Hi Andy,
This has come up a few times in the past (and we elected to not clean it up at the time, though it wasn't a decision to never do so!)
It would definitely be wrong if we had another driver binding against the resulting created device (funnily enough I reported a bug on a driver doing just that earlier this week), but in this case it's harmless because the the tear down will occur with a
put_device()ultimately callingdevice_release()anddevres_release_all()https://elixir.bootlin.com/linux/latest/source/drivers/base/core.c#L2211
Has a comment that covers this case (more or less).
"
* Some platform devices are driven without driver attached
* and managed resources may have been acquired. Make sure
* all resources are released.
"
Quoted 4 lines
Quoted 4 lines
Now, I definitely agree with your statement that it's a bit inconsistent to do this, just not the fixes tag.
One other suggestion below.
Andy, put a cover letter on these larger series - if nothing else it gives somewhere convenient for people to give tags for the whole series, or maintainer to say what they are doing with it.
Anyhow, I'm fine with the series, but will leave it on list for a while longer, particularly to get patch 6 some eyes + testing.
Currently I plan to drop the fixes tag from this first patch, but I'm prepared to be convinced it's a bug fix rather than a consistency cleanup.
Jonathan
Quoted 64 lines
Quoted 7 lines
Quoted 7 lines
---
v3: new fix-patchdrivers/iio/adc/meson_saradc.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)Quoted 12 lines
drivers/iio/adc/meson_saradc.c static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, · line 653
Quoted 9 lines
drivers/iio/adc/meson_saradc.c +1
-0@@ -650,11 +650,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, void __iomem *base) {struct meson_sar_adc_priv *priv =iio_priv (indio_dev); +struct device *dev = indio_dev->dev.parent;I'd slightly prefer the device was passed in explicitly to this function rather than using the parent assignment which feels a little fragile.
Meh, ignore this. I see from one of the later patches, the driver is already making the assumption this is set in other calls, so we aren't making anything worse with this change.
Jonathan
Quoted 37 lines
Quoted 36 lines
drivers/iio/adc/meson_saradc.c +4
-7struct clk_init_data init;const char *clk_parents[1 ]; - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_div" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_div" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -670,13 +670,11 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_div.hw.init = &init; priv->clk_div.flags =0 ; - priv->adc_div_clk =devm_clk_register (&indio_dev->dev, - &priv->clk_div.hw); + priv->adc_div_clk =devm_clk_register (dev, &priv->clk_div.hw);if (WARN_ON (IS_ERR (priv->adc_div_clk)))return PTR_ERR (priv->adc_div_clk); - init.name =devm_kasprintf (&indio_dev->dev,GFP_KERNEL ,"%s#adc_en" , -dev_name (indio_dev->dev.parent)); + init.name =devm_kasprintf (dev,GFP_KERNEL ,"%s#adc_en" ,dev_name (dev));if (!init.name)return -ENOMEM ;@@ -690,7 +688,7 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, priv->clk_gate.bit_idx =__ffs (MESON_SAR_ADC_REG3_CLK_EN ); priv->clk_gate.hw.init = &init; - priv->adc_clk =devm_clk_register (&indio_dev->dev, &priv->clk_gate.hw); + priv->adc_clk =devm_clk_register (dev, &priv->clk_gate.hw);if (WARN_ON (IS_ERR (priv->adc_clk)))return PTR_ERR (priv->adc_clk);
Quoted 2 lines · Jonathan Cameron
On Fri, 3 Jun 2022 17:23:07 +0100
Jonathan Cameron <[email protected]> wrote:
...
Quoted 3 lines
Andy, put a cover letter on these larger series - if nothing else it gives somewhere convenient for people to give tags for the whole series, or maintainer to say what they are doing with it.
I'll try to remember this. The series was started from only a couple of patches and grew to this big, and I forgot to add a cover letter when it seems not anymore obvious what has been done.
Quoted 5 lines
Anyhow, I'm fine with the series, but will leave it on list for a while longer, particularly to get patch 6 some eyes + testing.
Currently I plan to drop the fixes tag from this first patch, but I'm prepared to be convinced it's a bug fix rather than a consistency cleanup.
Fine with me, thanks!
Signature · 2 lines
With Best Regards, Andy Shevchenko
Jonathan Cameron
maintainerQuoted 14 lines · On Fri, 3 Jun 2022 19:54:43 +0300 Andy Shevchenko…
Quoted 2 lines · Jonathan Cameron
On Fri, 3 Jun 2022 17:23:07 +0100
Jonathan Cameron <[email protected]> wrote:...
Quoted 3 lines
Andy, put a cover letter on these larger series - if nothing else it gives somewhere convenient for people to give tags for the whole series, or maintainer to say what they are doing with it.
I'll try to remember this. The series was started from only a couple of patches and grew to this big, and I forgot to add a cover letter when it seems not anymore obvious what has been done.
Quoted 8 lines
Quoted 5 lines
Anyhow, I'm fine with the series, but will leave it on list for a while longer, particularly to get patch 6 some eyes + testing.
Currently I plan to drop the fixes tag from this first patch, but I'm prepared to be convinced it's a bug fix rather than a consistency cleanup.
Fine with me, thanks!
Applied to the togreg branch of iio.git and pushed out as testing for all the normal reasons.
Thanks,
Jonathan
Quoted 10 lines · Andy Shevchenko
It feels wrong and actually inconsistent to attach managed resources to the IIO device object, which is child of the physical device object. The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
Fixes 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")Suggested-by Lars-Peter Clausen <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>
I am also fine if the Fixes tag is being dropped - please keep my Reviewed-by in that case.