DC Patches May 30, 2022
cover DC Patches May 30, 2022
* DPP DTO fix
* Transient encoder fix
* Restrict the reading of LTTPR capabilities in LTTPR mode
* Increase maximum stages for BB
* Distinguish HDMI DTO from DP DTO
* Optimized blank calculations
* More robust DP MST hotplug support
* eDP bug fix relating to ODM
* Revert a patch that caused a regression with DP
* min comp buffer size fix
* Make DP easier to debug
* Calculate the maximum OLED brightness correctly
* 3 plane MPO.
Anthony Koo (1):
drm/amd/display: [FW Promotion] Release 0.0.119.0
Aric Cyr (2):
drm/amd/display: 3.2.188
drm/amd/display: 3.2.189
Chris Park (1):
drm/amd/display: Add HDMI member to DTO
Duncan Ma (3):
drm/amd/display: Blank eDP on enable drv if odm enabled drm/amd/display: Correct min comp buffer size drm/amd/display: Fix dpp dto for disabled pipes
Gabe Teeger (1):
drm/amd/display: Update optimized blank calc and programming
Hansen Dsouza (1):
drm/amd/display: Enable 3 plane MPO
Jimmy Kizito (2):
drm/amd/display: Fix entry into transient encoder assignment mode. drm/amd/display: Avoid reading LTTPR caps in non-LTTPR mode.
Lei, Jun (1):
drm/amd/display: Extend soc BB capabilitiy
Nicholas Kazlauskas (1):
Revert "drm/amd/display: Pass the new context into disable OTG WA"
Roman Li (1):
drm/amd/display: Cap OLED brightness per max frame-average luminance
Wayne Lin (1):
drm/amd/display: Detect dpcd_rev when hotplug mst monitor
Wenjing Liu (1):
drm/amd/display: add DP sanity checks during enable stream
.../gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 8 +- .../display/amdgpu_dm/amdgpu_dm_mst_types.c | 38 ++++++++- .../display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c | 8 +- .../dc/clk_mgr/dcn315/dcn315_clk_mgr.c | 8 +- .../dc/clk_mgr/dcn316/dcn316_clk_mgr.c | 8 +- .../gpu/drm/amd/display/dc/core/dc_debug.c | 2 + drivers/gpu/drm/amd/display/dc/core/dc_link.c | 21 +++++ .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 77 +++++++++++++------ .../drm/amd/display/dc/core/dc_link_enc_cfg.c | 45 ++++++++++- drivers/gpu/drm/amd/display/dc/dc.h | 4 +- drivers/gpu/drm/amd/display/dc/dc_link.h | 1 + .../drm/amd/display/dc/dcn20/dcn20_hwseq.c | 4 + .../display/dc/dcn31/dcn31_dio_link_encoder.c | 6 ++ .../gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c | 2 +- .../drm/amd/display/dc/dcn31/dcn31_hwseq.c | 24 +++++- .../drm/amd/display/dc/dcn31/dcn31_resource.c | 1 - .../amd/display/dc/dcn315/dcn315_resource.c | 6 +- .../amd/display/dc/dcn316/dcn316_resource.c | 6 +- .../gpu/drm/amd/display/dc/dml/dc_features.h | 2 +- .../drm/amd/display/dc/dml/dcn31/dcn31_fpu.c | 3 +- .../dc/dml/dcn31/display_rq_dlg_calc_31.c | 16 +--- .../amd/display/dc/dml/display_mode_structs.h | 1 + .../drm/amd/display/dc/dml/display_mode_vba.h | 1 + .../gpu/drm/amd/display/dc/inc/core_status.h | 2 +- drivers/gpu/drm/amd/display/dc/inc/hw/dccg.h | 1 + .../gpu/drm/amd/display/dc/inc/link_enc_cfg.h | 7 ++ .../gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 1 + 27 files changed, 234 insertions(+), 69 deletions(-)
Signature · 1 line
2.36.1
PATCH 1/16 drm/amd/display: Update optimized blank calc and programming
From: Gabe Teeger <[email protected]>
[Why]
The existing calculations in DCN3.1 were placeholder and need to be replaced with HW team approved calculations.
[How]
The new calculations add new parameters to the bounding box and pipe params - VblankNom and the bounding box default.
The placeholder calculations are dropped from DCN3.1 in the meantime while we work out hardware approved replacements.
Also fix a bug where we wipe out other register contents with a REG_SET instead of a REG_UPDATE for the register we were programming the min_dst_y_next_start_optimized.
--- .../gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c | 2 +- .../drm/amd/display/dc/dcn31/dcn31_resource.c | 1 - .../dc/dml/dcn31/display_rq_dlg_calc_31.c | 16 ++-------------- .../amd/display/dc/dml/display_mode_structs.h | 1 + .../drm/amd/display/dc/dml/display_mode_vba.h | 1 + 5 files changed, 5 insertions(+), 16 deletions(-)
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c +1 -1
@@ -59,7 +59,7 @@ static void hubp31_program_extended_blank(struct hubp *hubp, {struct dcn20_hubp *hubp2 =TO_DCN20_HUBP (hubp); -REG_SET (BLANK_OFFSET_1 ,0 ,MIN_DST_Y_NEXT_START , min_dst_y_next_start_optimized); +REG_UPDATE (BLANK_OFFSET_1 ,MIN_DST_Y_NEXT_START , min_dst_y_next_start_optimized); }static struct hubp_funcs dcn31_hubp_funcs = {
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c +0 -1
@@ -1651,7 +1651,6 @@ int dcn31_populate_dml_pipes_from_context(continue ; pipe = &res_ctx->pipe_ctx[i]; timing = &pipe->stream->timing; -if (pipe->plane_state && (pipe->plane_state->src_rect.height < pipe->plane_state->dst_rect.height || pipe->plane_state->src_rect.width < pipe->plane_state->dst_rect.width))
drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.c +2 -14
@@ -1055,7 +1055,6 @@ static void dml_rq_dlg_get_dlg_params(float vba__refcyc_per_req_delivery_pre_l =get_refcyc_per_req_delivery_pre_l_in_us (mode_lib, e2e_pipe_param, num_pipes, pipe_idx) * refclk_freq_in_mhz;// From VBA float vba__refcyc_per_req_delivery_l =get_refcyc_per_req_delivery_l_in_us (mode_lib, e2e_pipe_param, num_pipes, pipe_idx) * refclk_freq_in_mhz;// From VBA -int blank_lines;memset (disp_dlg_regs,0 ,sizeof (*disp_dlg_regs));memset (disp_ttu_regs,0 ,sizeof (*disp_ttu_regs));
@@ -1079,20 +1078,9 @@ static void dml_rq_dlg_get_dlg_params( min_ttu_vblank =get_min_ttu_vblank_in_us (mode_lib, e2e_pipe_param, num_pipes, pipe_idx);// From VBA dlg_vblank_start = interlaced ? (vblank_start /2 ) : vblank_start; - disp_dlg_regs->min_dst_y_next_start = (unsigned int ) (((double ) dlg_vblank_start) *dml_pow (2 ,2 )); - blank_lines = (dst->vblank_end + dst->vtotal_min - dst->vblank_start - dst->vstartup_start -1 ); -if (blank_lines <0 ) - blank_lines =0 ; -if (blank_lines !=0 ) { - disp_dlg_regs->optimized_min_dst_y_next_start_us = - ((unsigned int ) blank_lines * dst->hactive) / (unsigned int ) dst->pixel_rate_mhz; - disp_dlg_regs->optimized_min_dst_y_next_start = - (unsigned int )(((double ) (dlg_vblank_start + blank_lines)) *dml_pow (2 ,2 )); - }else { -// use unoptimized value - disp_dlg_regs->optimized_min_dst_y_next_start = disp_dlg_regs->min_dst_y_next_start; - } + disp_dlg_regs->optimized_min_dst_y_next_start_us =0 ; + disp_dlg_regs->optimized_min_dst_y_next_start = disp_dlg_regs->min_dst_y_next_start;ASSERT (disp_dlg_regs->min_dst_y_next_start < (unsigned int )dml_pow (2 ,18 ));dml_print ("DML_DLG: %s: min_ttu_vblank (us) = %3.2f\n" , __func__, min_ttu_vblank);
drivers/gpu/drm/amd/display/dc/dml/display_mode_structs.h +1 -0
@@ -224,6 +224,7 @@ struct _vcs_dpi_ip_params_st {unsigned int can_vstartup_lines_exceed_vsync_plus_back_porch_lines_minus_one;unsigned int bug_forcing_LC_req_same_size_fixed;unsigned int number_of_cursors; +unsigned int VBlankNomDefaultUS; };struct _vcs_dpi_display_xfc_params_st {
drivers/gpu/drm/amd/display/dc/dml/display_mode_vba.h +1 -0
@@ -355,6 +355,7 @@ struct vba_vars_st {unsigned int CursorBPP[DC__NUM_DPP__MAX ][DC__NUM_CURSOR__MAX ];bool XFCEnabled[DC__NUM_DPP__MAX ];bool ScalerEnabled[DC__NUM_DPP__MAX ]; +unsigned int VBlankNom[DC__NUM_DPP__MAX ];// Intermediates/Informational bool ImmediateFlipSupport;
Signature · 1 line
2.36.1
PATCH 2/16 drm/amd/display: Detect dpcd_rev when hotplug mst monitor
In reply to Hamza MahfoozFrom: Wayne Lin <[email protected]>
[Why]
Once mst topology is constructed, later on new connected monitors are reported to source by CSN message. Within CSN, there is no carried info of DPCD_REV comparing to LINK_ADDRESS reply. As the result, we might leave some ports connected to DP but without DPCD revision number which will affect us determining the capability of the DP Rx.
[How]
Send out remote DPCD read when the port's dpcd_rev is 0x0 in detect_ctx(). Firstly, read out the value from DPCD 0x2200. If the return value is 0x0, it's likely the DP1.2 DP Rx then we reques revision from DPCD 0x0 again.
--- .../display/amdgpu_dm/amdgpu_dm_mst_types.c | 38 ++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c +37 -1
@@ -344,12 +344,48 @@ dm_dp_mst_detect(struct drm_connector *connector, {struct amdgpu_dm_connector *aconnector =to_amdgpu_dm_connector (connector);struct amdgpu_dm_connector *master = aconnector->mst_port; +struct drm_dp_mst_port *port = aconnector->port; +int connection_status;if (drm_connector_is_unregistered (connector))return connector_status_disconnected; -return drm_dp_mst_detect_port (connector, ctx, &master->mst_mgr, + connection_status =drm_dp_mst_detect_port (connector, ctx, &master->mst_mgr, aconnector->port); + +if (port->pdt !=DP_PEER_DEVICE_NONE && !port->dpcd_rev) { +uint8_t dpcd_rev; +int ret; + + ret =drm_dp_dpcd_readb (&port->aux,DP_DP13_DPCD_REV , &dpcd_rev); + +if (ret ==1 ) { + port->dpcd_rev = dpcd_rev; + +/* Could be DP1.2 DP Rx case*/ +if (!dpcd_rev) { + ret =drm_dp_dpcd_readb (&port->aux,DP_DPCD_REV , &dpcd_rev); + +if (ret ==1 ) + port->dpcd_rev = dpcd_rev; + } + +if (!dpcd_rev) +DRM_DEBUG_KMS ("Can't decide DPCD revision number!" ); + } + +/* +* Could be legacy sink, logical port etc on DP1.2. +* Will get Nack under these cases when issue remote +* DPCD read. +*/ +if (ret !=1 ) +DRM_DEBUG_KMS ("Can't access DPCD" ); + }else if (port->pdt ==DP_PEER_DEVICE_NONE ) { + port->dpcd_rev =0 ; + } + +return connection_status; } static int dm_dp_mst_atomic_check(struct drm_connector *connector,
Signature · 1 line
2.36.1
PATCH 3/16 Revert "drm/amd/display: Pass the new context into disable OTG WA"
In reply to Hamza MahfoozFrom: Nicholas Kazlauskas <[email protected]>
This reverts commit 25b1b4128c75bc9b9cf033425427d085f97439ec.
Causes a hang when hotplugging DP, shutting down system, or enabling dual eDP.
--- .../gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c | 8 ++++---- .../drm/amd/display/dc/clk_mgr/dcn315/dcn315_clk_mgr.c | 8 ++++---- .../drm/amd/display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c | 8 ++++---- 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c +4 -4
@@ -99,13 +99,13 @@ static int dcn31_get_active_display_cnt_wa(return display_count; } -static void dcn31_disable_otg_wa (struct clk_mgr *clk_mgr_base,struct dc_state *context,bool disable) +static void dcn31_disable_otg_wa (struct clk_mgr *clk_mgr_base,bool disable) {struct dc *dc = clk_mgr_base->ctx->dc;int i;for (i =0 ; i < dc->res_pool->pipe_count; ++i) { -struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i]; +struct pipe_ctx *pipe = &dc->current_state->res_ctx.pipe_ctx[i];if (pipe->top_pipe || pipe->prev_odm_pipe)continue ;
@@ -211,11 +211,11 @@ void dcn31_update_clocks(struct clk_mgr *clk_mgr_base, }if (should_set_clock (safe_to_lower, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz)) { -dcn31_disable_otg_wa (clk_mgr_base, context, true); +dcn31_disable_otg_wa (clk_mgr_base, true); clk_mgr_base->clks.dispclk_khz = new_clocks->dispclk_khz;dcn31_smu_set_dispclk (clk_mgr, clk_mgr_base->clks.dispclk_khz); -dcn31_disable_otg_wa (clk_mgr_base, context, false); +dcn31_disable_otg_wa (clk_mgr_base, false); update_dispclk = true; }
drivers/gpu/drm/amd/display/dc/clk_mgr/dcn315/dcn315_clk_mgr.c +4 -4
@@ -79,13 +79,13 @@ static int dcn315_get_active_display_cnt_wa(return display_count; } -static void dcn315_disable_otg_wa (struct clk_mgr *clk_mgr_base,struct dc_state *context,bool disable) +static void dcn315_disable_otg_wa (struct clk_mgr *clk_mgr_base,bool disable) {struct dc *dc = clk_mgr_base->ctx->dc;int i;for (i =0 ; i < dc->res_pool->pipe_count; ++i) { -struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i]; +struct pipe_ctx *pipe = &dc->current_state->res_ctx.pipe_ctx[i];if (pipe->top_pipe || pipe->prev_odm_pipe)continue ;
@@ -173,11 +173,11 @@ static void dcn315_update_clocks(struct clk_mgr *clk_mgr_base, }if (should_set_clock (safe_to_lower, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz)) { -dcn315_disable_otg_wa (clk_mgr_base, context, true); +dcn315_disable_otg_wa (clk_mgr_base, true); clk_mgr_base->clks.dispclk_khz = new_clocks->dispclk_khz;dcn315_smu_set_dispclk (clk_mgr, clk_mgr_base->clks.dispclk_khz); -dcn315_disable_otg_wa (clk_mgr_base, context, false); +dcn315_disable_otg_wa (clk_mgr_base, false); update_dispclk = true; }
drivers/gpu/drm/amd/display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c +4 -4
@@ -112,13 +112,13 @@ static int dcn316_get_active_display_cnt_wa(return display_count; } -static void dcn316_disable_otg_wa (struct clk_mgr *clk_mgr_base,struct dc_state *context,bool disable) +static void dcn316_disable_otg_wa (struct clk_mgr *clk_mgr_base,bool disable) {struct dc *dc = clk_mgr_base->ctx->dc;int i;for (i =0 ; i < dc->res_pool->pipe_count; ++i) { -struct pipe_ctx *pipe = &context->res_ctx.pipe_ctx[i]; +struct pipe_ctx *pipe = &dc->current_state->res_ctx.pipe_ctx[i];if (pipe->top_pipe || pipe->prev_odm_pipe)continue ;
@@ -221,11 +221,11 @@ static void dcn316_update_clocks(struct clk_mgr *clk_mgr_base, }if (should_set_clock (safe_to_lower, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz)) { -dcn316_disable_otg_wa (clk_mgr_base, context, true); +dcn316_disable_otg_wa (clk_mgr_base, true); clk_mgr_base->clks.dispclk_khz = new_clocks->dispclk_khz;dcn316_smu_set_dispclk (clk_mgr, clk_mgr_base->clks.dispclk_khz); -dcn316_disable_otg_wa (clk_mgr_base, context, false); +dcn316_disable_otg_wa (clk_mgr_base, false); update_dispclk = true; }
Signature · 1 line
2.36.1
PATCH 4/16 drm/amd/display: Blank eDP on enable drv if odm enabled
In reply to Hamza MahfoozFrom: Duncan Ma <[email protected]>
[Why]
For panels with pixel clock > 1200MHz that require ODM in pre-OS, when driver is disabled in OS, odm is enabled. Upon driver enablement, corruption is seen if odm was originally enabled. DP_PIXEL_COMBINE and pixelclk must be programmed prior to programming the optc-odm registers. However, eDP displays aren't blanked prior to initializing odm in this case.
[How]
Upon driver enablement, check whether odm is enabled, if so, blank eDP prior to programming optc-odm registers.
--- drivers/gpu/drm/amd/display/dc/core/dc_link.c | 20 +++++++++++++++++ drivers/gpu/drm/amd/display/dc/dc.h | 1 + drivers/gpu/drm/amd/display/dc/dc_link.h | 1 + .../drm/amd/display/dc/dcn31/dcn31_hwseq.c | 22 +++++++++++++++++++ 4 files changed, 44 insertions(+)
drivers/gpu/drm/amd/display/dc/core/dc_link.c +20 -0
@@ -2126,6 +2126,26 @@ void dc_link_blank_all_dp_displays(struct dc *dc) } +void dc_link_blank_all_edp_displays (struct dc *dc) +{ +unsigned int i; +uint8_t dpcd_power_state ='\0' ; +enum dc_status status =DC_ERROR_UNEXPECTED ; + +for (i =0 ; i < dc->link_count; i++) { +if ((dc->links[i]->connector_signal !=SIGNAL_TYPE_EDP ) || + (!dc->links[i]->edp_sink_present)) +continue ; + +/* if any of the displays are lit up turn them off */ + status =core_link_read_dpcd (dc->links[i],DP_SET_POWER , + &dpcd_power_state,sizeof (dpcd_power_state)); + +if (status ==DC_OK && dpcd_power_state ==DP_POWER_STATE_D0 ) +dc_link_blank_dp_stream (dc->links[i], true); + } +} +void dc_link_blank_dp_stream (struct dc_link *link,bool hw_init) {unsigned int j;
drivers/gpu/drm/amd/display/dc/dc.h +1 -0
@@ -202,6 +202,7 @@ struct dc_caps {bool vbios_lttpr_aware;bool vbios_lttpr_enable;uint32_t max_otg_num; +bool seamless_odm; };struct dc_bug_wa {
drivers/gpu/drm/amd/display/dc/dc_link.h +1 -0
@@ -321,6 +321,7 @@ bool dc_link_setup_psr(struct dc_link *dc_link,void dc_link_get_psr_residency (const struct dc_link *link,uint32_t *residency);void dc_link_blank_all_dp_displays (struct dc *dc); +void dc_link_blank_all_edp_displays (struct dc *dc);void dc_link_blank_dp_stream (struct dc_link *link,bool hw_init);
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c +22 -0
@@ -213,6 +213,28 @@ void dcn31_init_hw(struct dc *dc)* everything down. */ if (dcb->funcs->is_accelerated_mode (dcb) || !dc->config.seamless_boot_edp_requested) { + +// we want to turn off edp displays if odm is enabled and no seamless boot +if (!dc->caps.seamless_odm) { +for (i =0 ; i < dc->res_pool->timing_generator_count; i++) { +struct timing_generator *tg = dc->res_pool->timing_generators[i]; +uint32_t num_opps, opp_id_src0, opp_id_src1; + + num_opps =1 ; +if (tg) { +if (tg->funcs->is_tg_enabled (tg) && tg->funcs->get_optc_source) { + tg->funcs->get_optc_source (tg, &num_opps, + &opp_id_src0, &opp_id_src1); + } + } + +if (num_opps >1 ) { +dc_link_blank_all_edp_displays (dc); +break ; + } + } + } + hws->funcs.init_pipes (dc, dc->current_state);if (dc->res_pool->hubbub->funcs->allow_self_refresh_control) dc->res_pool->hubbub->funcs->allow_self_refresh_control(dc->res_pool->hubbub,
Signature · 1 line
2.36.1
PATCH 5/16 drm/amd/display: Correct min comp buffer size
In reply to Hamza MahfoozFrom: Duncan Ma <[email protected]>
[Why]
In 3-way mpo pipes, there is a case that we overbook the CRB buffer size. At rare instances, overbooking the crb will cause underflow. This only happens when det_size changes dynamically based on pipe_cnt.
[How]
Set min compbuff size to 1 segment when preparing BW.
--- drivers/gpu/drm/amd/display/dc/dml/dcn31/dcn31_fpu.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dml/dcn31/dcn31_fpu.c +2 -1
@@ -201,7 +201,7 @@ struct _vcs_dpi_ip_params_st dcn3_15_ip = { .hostvm_max_page_table_levels = 2, .rob_buffer_size_kbytes = 64, .det_buffer_size_kbytes = DCN3_15_DEFAULT_DET_SIZE, - .min_comp_buffer_size_kbytes = DCN3_15_MIN_COMPBUF_SIZE_KB, + .min_comp_buffer_size_kbytes = 64, .config_return_buffer_size_in_kbytes = 1024, .compressed_buffer_segment_size_in_kbytes = 64, .meta_fifo_size_in_kentries = 32,
@@ -297,6 +297,7 @@ struct _vcs_dpi_ip_params_st dcn3_16_ip = { .hostvm_max_page_table_levels = 2, .rob_buffer_size_kbytes = 64, .det_buffer_size_kbytes = DCN3_16_DEFAULT_DET_SIZE, + .min_comp_buffer_size_kbytes = 64, .config_return_buffer_size_in_kbytes = 1024, .compressed_buffer_segment_size_in_kbytes = 64, .meta_fifo_size_in_kentries = 32,
Signature · 1 line
2.36.1
PATCH 6/16 drm/amd/display: add DP sanity checks during enable stream
In reply to Hamza MahfoozFrom: Wenjing Liu <[email protected]>
[why]
1. When HPD deassertion is pulled in the middle of enabe stream link training, we will abort current training and turn off PHY. This causes current link settings to be zeroed this causes later stream enablement sequence to fail as we prefer to carry on enablement process despite of link training failure for SST.
2. When HPD is toggled after detection before before the enable stream sequence as a result. There could be a race condition where we could end up enable stream based on the previous link even though the link is updated after the HPD toggle. This causes an issue where our link bandwidth is no longer enough to accommodate the timing therefore causes us to oversubscribe MST payload time slots. As discussed we decided to add basic sanity check to make sure that our code can handle the oversubscription failure silently without system hang.
[how]
1. Keep PHY powered on when HPD is deasserted during enable stream and wait for the detection sequence to power it off later.
2. Do not allocate payload if the required timeslot for current timing is greater than 64 timeslots.
--- drivers/gpu/drm/amd/display/dc/core/dc_debug.c | 2 ++ drivers/gpu/drm/amd/display/dc/core/dc_link.c | 1 + drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c | 16 +++++++++++----- drivers/gpu/drm/amd/display/dc/inc/core_status.h | 2 +- 4 files changed, 15 insertions(+), 6 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_debug.c +2 -0
@@ -422,6 +422,8 @@ char *dc_status_to_str(enum dc_status status)return "The value specified is not supported." ;case DC_NO_LINK_ENC_RESOURCE :return "No link encoder resource" ; +case DC_FAIL_DP_PAYLOAD_ALLOCATION : +return "Fail dp payload allocation" ;case DC_ERROR_UNEXPECTED :return "Unexpected error" ; }
drivers/gpu/drm/amd/display/dc/core/dc_link.c +1 -0
@@ -3566,6 +3566,7 @@ static enum dc_status dc_link_update_sst_payload(struct pipe_ctx *pipe_ctx,"allocation table for " "pipe idx: %d\n" , pipe_ctx->pipe_idx); +return DC_FAIL_DP_PAYLOAD_ALLOCATION ; } proposed_table.stream_allocations[0 ].hpo_dp_stream_enc = pipe_ctx->stream_res.hpo_dp_stream_enc;
drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c +11 -5
@@ -2875,10 +2875,13 @@ bool perform_link_training_with_retries( fail_count++;dp_trace_lt_fail_count_update (link, fail_count, false); -/* latest link training still fail, skip delay and keep PHY on -*/ -if (j == (attempts -1 ) && link->ep_type ==DISPLAY_ENDPOINT_PHY ) -break ; +if (link->ep_type ==DISPLAY_ENDPOINT_PHY ) { +/* latest link training still fail or link training is aborted +* skip delay and keep PHY on +*/ +if (j == (attempts -1 ) || (status ==LINK_TRAINING_ABORT )) +break ; + } DC_LOG_WARNING("%s: Link training attempt %u of %d failed @ rate(%d) x lane(%d)\n", __func__, (unsigned int)j + 1, attempts, cur_link_settings.link_rate,
@@ -6869,6 +6872,10 @@ bool dpcd_write_128b_132b_sst_payload_allocation_table(if (allocate) { avg_time_slots_per_mtp =calculate_sst_avg_time_slots_per_mtp (stream, link); req_slot_count =dc_fixpt_ceil (avg_time_slots_per_mtp); +/// Validation should filter out modes that exceed link BW +ASSERT (req_slot_count <=MAX_MTP_SLOT_COUNT ); +if (req_slot_count >MAX_MTP_SLOT_COUNT ) +return false; }else {/// Leave req_slot_count = 0 if allocate is false. }
@@ -6896,7 +6903,6 @@ bool dpcd_write_128b_132b_sst_payload_allocation_table( &start_time_slot, 1); -ASSERT (req_slot_count <=MAX_MTP_SLOT_COUNT );/// Validation should filter out modes that exceed link BW core_link_write_dpcd( link, DP_PAYLOAD_ALLOCATE_TIME_SLOT_COUNT,
drivers/gpu/drm/amd/display/dc/inc/core_status.h +1 -1
@@ -54,7 +54,7 @@ enum dc_status {DC_UNSUPPORTED_VALUE =25 ,DC_NO_LINK_ENC_RESOURCE =26 , - +DC_FAIL_DP_PAYLOAD_ALLOCATION =27 , DC_ERROR_UNEXPECTED = -1 };
Signature · 1 line
2.36.1
PATCH 7/16 drm/amd/display: Cap OLED brightness per max frame-average luminance
In reply to Hamza MahfoozFrom: Roman Li <[email protected]>
[Why]
For OLED eDP the Display Manager uses max_cll value as a limit for brightness control.max_cll defines the content light luminance for individual pixel. Whereas max_fall defines frame-average level luminance. The user may not observe the difference in brightness in between max_fall and max_cll.
That negatively impacts the user experience.
[How]
Use max_fall value instead of max_cll as a limit for brightness control.
--- drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c +4 -4
@@ -2813,7 +2813,7 @@ static struct drm_mode_config_helper_funcs amdgpu_dm_mode_config_helperfuncs = {static void update_connector_ext_caps (struct amdgpu_dm_connector *aconnector) { -u32 max_cll, min_cll, max, min, q, r; +u32 max_avg, min_cll, max, min, q, r;struct amdgpu_dm_backlight_caps *caps;struct amdgpu_display_manager *dm;struct drm_connector *conn_base;
@@ -2843,7 +2843,7 @@ static void update_connector_ext_caps(struct amdgpu_dm_connector *aconnector) caps = &dm->backlight_caps[i]; caps->ext_caps = &aconnector->dc_link->dpcd_sink_ext_caps; caps->aux_support = false; - max_cll = conn_base->hdr_sink_metadata.hdmi_type1.max_cll; + max_avg = conn_base->hdr_sink_metadata.hdmi_type1.max_fall; min_cll = conn_base->hdr_sink_metadata.hdmi_type1.min_cll;if (caps->ext_caps->bits.oled ==1 /*||
@@ -2871,8 +2871,8 @@ static void update_connector_ext_caps(struct amdgpu_dm_connector *aconnector)* The results of the above expressions can be verified at * pre_computed_values. */ - q = max_cll >>5 ; - r = max_cll %32 ; + q = max_avg >>5 ; + r = max_avg %32 ; max = (1 << q) * pre_computed_values[r];// min luminance: maxLum * (CV/255)^2 / 100
Signature · 1 line
2.36.1
Re: [PATCH 07/16] drm/amd/display: Cap OLED brightness per max frame-average luminance
Hi Roman:
Can the panel achieve the max peak luminance
if it is limited in frame-average luminance?
Regards,
Aaron
RE: [PATCH 07/16] drm/amd/display: Cap OLED brightness per max frame-average luminance
[AMD Official Use Only - General]
Hi Aaron,
Yes, the panel brightness should reach max after we send max-fall value as backlight current peak.
Thanks,
Roman
Quoted 25 lines
-----Original Message-----
From: Aaron Ma <[email protected]>
Sent: Wednesday, June 8, 2022 6:02 AM
To: Mahfooz, Hamza <[email protected]>; Li, Roman <[email protected]>
Cc: Pillai, Aurabindo <[email protected]>; Lakha, Bhawanpreet <[email protected]>; Wentland, Harry <[email protected]>; Siqueira, Rodrigo <[email protected]>; Li, Sun peng (Leo) <[email protected]>; Gutierrez, Agustin <[email protected]>; amd- [email protected]; Zuo, Jerry <[email protected]>; Kotarac, Pavle <[email protected]>; Zhuo, Qingqing (Lillian) <[email protected]>; Chiu, Solomon <[email protected]>; Wang, Chao-kai (Stylon) <[email protected]>; Lin, Wayne <[email protected]>
Subject: Re: [PATCH 07/16] drm/amd/display: Cap OLED brightness per max frame-average luminanceHi Roman:
Can the panel achieve the max peak luminance if it is limited in frame-average luminance?
Regards,
Aaron
PATCH 8/16 drm/amd/display: Enable 3 plane MPO
In reply to Hamza MahfoozFrom: Hansen Dsouza <[email protected]>
[why and how]
3 plane MPO is a new feature missing in a few resource files Enable 3 plane MPO by setting slave planes to 2
--- drivers/gpu/drm/amd/display/dc/dcn315/dcn315_resource.c | 6 +++--- drivers/gpu/drm/amd/display/dc/dcn316/dcn316_resource.c | 6 +++--- 2 files changed, 6 insertions(+), 6 deletions(-)
drivers/gpu/drm/amd/display/dc/dcn315/dcn315_resource.c +3 -3
@@ -1762,9 +1762,9 @@ static bool dcn315_resource_construct( dc->caps.max_cursor_size =256 ; dc->caps.min_horizontal_blanking_period =80 ; dc->caps.dmdata_alloc_size =2048 ; - dc->caps.max_slave_planes =1 ; - dc->caps.max_slave_yuv_planes =1 ; - dc->caps.max_slave_rgb_planes =1 ; + dc->caps.max_slave_planes =2 ; + dc->caps.max_slave_yuv_planes =2 ; + dc->caps.max_slave_rgb_planes =2 ; dc->caps.post_blend_color_processing = true; dc->caps.force_dp_tps4_for_cp2520 = true; dc->caps.dp_hpo = true;
drivers/gpu/drm/amd/display/dc/dcn316/dcn316_resource.c +3 -3
@@ -1764,9 +1764,9 @@ static bool dcn316_resource_construct( dc->caps.max_cursor_size =256 ; dc->caps.min_horizontal_blanking_period =80 ; dc->caps.dmdata_alloc_size =2048 ; - dc->caps.max_slave_planes =1 ; - dc->caps.max_slave_yuv_planes =1 ; - dc->caps.max_slave_rgb_planes =1 ; + dc->caps.max_slave_planes =2 ; + dc->caps.max_slave_yuv_planes =2 ; + dc->caps.max_slave_rgb_planes =2 ; dc->caps.post_blend_color_processing = true; dc->caps.force_dp_tps4_for_cp2520 = true; dc->caps.dp_hpo = true;
Signature · 1 line
2.36.1
PATCH 9/16 drm/amd/display: [FW Promotion] Release 0.0.119.0
In reply to Hamza MahfoozFrom: Anthony Koo <[email protected]>
--- drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/amd/display/dmub/inc/dmub_cmd.h +1 -0
@@ -1363,6 +1363,7 @@ struct dmub_rb_cmd_dp_set_config_reply {struct dmub_cmd_hpd_state_query_data {uint8_t instance;/**< HPD instance or DPIA instance */ uint8_t result;/**< For returning HPD state */ +uint16_t pad;/** < Alignment */ enum aux_channel_type ch_type;/**< enum aux_channel_type */ enum aux_return_code_type status;/**< for returning the status of command */ };
Signature · 1 line
2.36.1
PATCH 10/16 drm/amd/display: 3.2.188
In reply to Hamza MahfoozFrom: Aric Cyr <[email protected]>
This version brings along the following:
- Optimized blank calculations
- More robust DP MST hotplug support
- eDP bug fix relating to ODM
- Revert a patch that caused a regression with DP
- min comp buffer size fix
- Make DP easier to debug
- Calculate the maximum OLED brightness correctly
- 3 plane MPO.
--- drivers/gpu/drm/amd/display/dc/dc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dc.h +1 -1
@@ -47,7 +47,7 @@ struct aux_payload;struct set_config_cmd_payload ;struct dmub_notification ; -#define DC_VER "3.2.187" +#define DC_VER "3.2.188"#define MAX_SURFACES 3#define MAX_PLANES 6
Signature · 1 line
2.36.1
PATCH 11/16 drm/amd/display: Fix dpp dto for disabled pipes
In reply to Hamza MahfoozFrom: Duncan Ma <[email protected]>
[Why]
When switching from 1 pipe to 4to1 mpc combine, DppDtoClk aren't enabled for the disabled pipes pior to programming the pipes. Upon optimizing bandwidth, DppDto are enabled causing intermittent underflow.
[How]
Update dppclk dto whenever pipe are flagged to
enable.
--- drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c +4 -0
@@ -1412,11 +1412,15 @@ static void dcn20_update_dchubp_dpp(struct hubp *hubp = pipe_ctx->plane_res.hubp;struct dpp *dpp = pipe_ctx->plane_res.dpp;struct dc_plane_state *plane_state = pipe_ctx->plane_state; +struct dccg *dccg = dc->res_pool->dccg;bool viewport_changed = false;if (pipe_ctx->update_flags.bits.dppclk) dpp->funcs->dpp_dppclk_control (dpp, false, true); +if (pipe_ctx->update_flags.bits.enable) + dccg->funcs->update_dpp_dto (dccg, dpp->inst, pipe_ctx->plane_res.bw.dppclk_khz); +/* TODO: Need input parameter to tell current DCHUB pipe tie to which OTG * VTG is within DCHUBBUB which is commond block share by each pipe HUBP. * VTG is 1:1 mapping with OTG. Each pipe HUBP will select which VTG
Signature · 1 line
2.36.1
PATCH 12/16 drm/amd/display: Fix entry into transient encoder assignment mode.
In reply to Hamza MahfoozFrom: Jimmy Kizito <[email protected]>
[Why]
In some scenarios it is possible for the encoder assignment module to be set to "transient" mode even though there are no new encoder assignments.
This can lead to incorrect results when querying encoder assignment, which in turn can cause incorrect displays to be manipulated.
[How]
Only allow encoder assignment to be in transient mode of operation when there are valid new encoder assignments.
--- .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 17 ++++--- .../drm/amd/display/dc/core/dc_link_enc_cfg.c | 45 ++++++++++++++++++- .../display/dc/dcn31/dcn31_dio_link_encoder.c | 6 +++ .../drm/amd/display/dc/dcn31/dcn31_hwseq.c | 2 +- .../gpu/drm/amd/display/dc/inc/link_enc_cfg.h | 7 +++ 5 files changed, 69 insertions(+), 8 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c +11 -6
@@ -2812,8 +2812,8 @@ bool perform_link_training_with_retries( j =0 ;while (j < attempts && fail_count < (attempts *10 )) { -DC_LOG_HW_LINK_TRAINING ("%s: Beginning link training attempt %u of %d @ rate(%d) x lane(%d)\n" , - __func__, (unsigned int )j +1 , attempts, cur_link_settings.link_rate, +DC_LOG_HW_LINK_TRAINING ("%s: Beginning link(%d) training attempt %u of %d @ rate(%d) x lane(%d)\n" , + __func__, link->link_index, (unsigned int )j +1 , attempts, cur_link_settings.link_rate, cur_link_settings.lane_count); dp_enable_link_phy(
@@ -2883,8 +2883,8 @@ bool perform_link_training_with_retries(break ; } -DC_LOG_WARNING ("%s: Link training attempt %u of %d failed @ rate(%d) x lane(%d)\n" , - __func__, (unsigned int )j +1 , attempts, cur_link_settings.link_rate, +DC_LOG_WARNING ("%s: Link(%d) training attempt %u of %d failed @ rate(%d) x lane(%d)\n" , + __func__, link->link_index, (unsigned int )j +1 , attempts, cur_link_settings.link_rate, cur_link_settings.lane_count);dp_disable_link_phy (link, &pipe_ctx->link_res, signal);
@@ -2927,8 +2927,13 @@ bool perform_link_training_with_retries(*/ req_bw =dc_bandwidth_in_kbps_from_timing (&stream->timing); link_bw =dc_link_bandwidth_kbps (link, &cur_link_settings); -if (req_bw > link_bw) -break ; + is_link_bw_low = (req_bw > link_bw); + is_link_bw_min = ((cur_link_settings.link_rate <=LINK_RATE_LOW ) && + (cur_link_settings.lane_count <=LANE_COUNT_ONE )); +if (is_link_bw_low) +DC_LOG_WARNING ( +"%s: Link(%d) bandwidth too low after fallback req_bw(%d) > link_bw(%d)\n" , + __func__, link->link_index, req_bw, link_bw); }msleep (delay_between_attempts);
drivers/gpu/drm/amd/display/dc/core/dc_link_enc_cfg.c +44 -1
64 lines not on this page · raw message
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dio_link_encoder.c +6 -0
@@ -458,6 +458,7 @@ void dcn31_link_encoder_enable_dp_output(/* Enable transmitter and encoder. */ if (!link_enc_cfg_is_transmitter_mappable (enc->ctx->dc, enc)) { +DC_LOG_DEBUG ("%s: enc_id(%d)\n" , __func__, enc->preferred_engine);dcn20_link_encoder_enable_dp_output (enc, link_settings, clock_source); }else {
@@ -489,6 +490,7 @@ void dcn31_link_encoder_enable_dp_output(return ; } +DC_LOG_DEBUG ("%s: DPIA(%d) - enc_id(%d)\n" , __func__, dpia_control.dpia_id, dpia_control.enc_id);link_dpia_control (enc->ctx, &dpia_control); } }
@@ -503,6 +505,7 @@ void dcn31_link_encoder_enable_dp_mst_output(/* Enable transmitter and encoder. */ if (!link_enc_cfg_is_transmitter_mappable (enc->ctx->dc, enc)) { +DC_LOG_DEBUG ("%s: enc_id(%d)\n" , __func__, enc->preferred_engine);dcn10_link_encoder_enable_dp_mst_output (enc, link_settings, clock_source); }else {
@@ -534,6 +537,7 @@ void dcn31_link_encoder_enable_dp_mst_output(return ; } +DC_LOG_DEBUG ("%s: DPIA(%d) - enc_id(%d)\n" , __func__, dpia_control.dpia_id, dpia_control.enc_id);link_dpia_control (enc->ctx, &dpia_control); } }
@@ -547,6 +551,7 @@ void dcn31_link_encoder_disable_output(/* Disable transmitter and encoder. */ if (!link_enc_cfg_is_transmitter_mappable (enc->ctx->dc, enc)) { +DC_LOG_DEBUG ("%s: enc_id(%d)\n" , __func__, enc->preferred_engine);dcn10_link_encoder_disable_output (enc, signal); }else {
@@ -578,6 +583,7 @@ void dcn31_link_encoder_disable_output(return ; } +DC_LOG_DEBUG ("%s: DPIA(%d) - enc_id(%d)\n" , __func__, dpia_control.dpia_id, dpia_control.enc_id);link_dpia_control (enc->ctx, &dpia_control);link_encoder_disable (enc10);
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c +1 -1
@@ -613,7 +613,7 @@ void dcn31_reset_hw_ctx_wrap( }/* New dc_state in the process of being applied to hardware. */ - dc->current_state->res_ctx.link_enc_cfg_ctx.mode =LINK_ENC_CFG_TRANSIENT ; +link_enc_cfg_set_transient_mode (dc, dc->current_state, context); }void dcn31_setup_hpo_hw_control (const struct dce_hwseq *hws,bool enable)
drivers/gpu/drm/amd/display/dc/inc/link_enc_cfg.h +7 -0
@@ -110,4 +110,11 @@ bool link_enc_cfg_is_link_enc_avail(struct dc *dc, enum engine_id eng_id, struct/* Returns true if encoder assignments in supplied state pass validity checks. */ bool link_enc_cfg_validate (struct dc *dc,struct dc_state *state); +/* Set the link encoder assignment mode for the current_state to LINK_ENC_CFG_TRANSIENT mode. +* This indicates that a new_state is in the process of being applied to hardware. +* During this transition, old and new encoder assignments should be accessible from the old_state. +* Only allow transition into transient mode if new encoder assignments are valid. +*/ +void link_enc_cfg_set_transient_mode (struct dc *dc,struct dc_state *current_state,struct dc_state *new_state); +#endif /* DC_INC_LINK_ENC_CFG_H_ */
Signature · 1 line
2.36.1
PATCH 13/16 drm/amd/display: Avoid reading LTTPR caps in non-LTTPR mode.
In reply to Hamza MahfoozFrom: Jimmy Kizito <[email protected]>
[Why]
LTTPR capable devices on the DisplayPort path may assume that extended LTTPR AUX timeouts will be used after LTTPR capabilities are read.
When DPTX operates in non-LTTPR mode, AUX timeouts are not extended and this can result in AUX transactions timing out.
[How]
Use shared helper function to determine LTTPR mode and do not read LTTPR capabilities in non-LTTPR mode.
--- .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 44 +++++++++++++------ 1 file changed, 31 insertions(+), 13 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c +31 -13
@@ -5134,16 +5134,13 @@ static bool dpcd_read_sink_ext_caps(struct dc_link *link)return true; } -bool dp_retrieve_lttpr_cap (struct dc_link *link) +/* Logic to determine LTTPR mode */ +static void determine_lttpr_mode (struct dc_link *link) { -uint8_t lttpr_dpcd_data[8 ];bool allow_lttpr_non_transparent_mode =0 ;bool vbios_lttpr_enable = link->dc->caps.vbios_lttpr_enable;bool vbios_lttpr_interop = link->dc->caps.vbios_lttpr_aware; -enum dc_status status =DC_ERROR_UNEXPECTED ; -bool is_lttpr_present = false; -memset (lttpr_dpcd_data,'\0' ,sizeof (lttpr_dpcd_data));if ((link->dc->config.allow_lttpr_non_transparent_mode.bits.DP2_0 && link->dpcd_caps.channel_coding_cap.bits.DP_128b_132b_SUPPORTED)) {
@@ -5153,9 +5150,6 @@ bool dp_retrieve_lttpr_cap(struct dc_link *link) allow_lttpr_non_transparent_mode =1 ; } -/* -* Logic to determine LTTPR mode -*/ link->lttpr_mode =LTTPR_MODE_NON_LTTPR ;if (vbios_lttpr_enable && vbios_lttpr_interop) link->lttpr_mode =LTTPR_MODE_NON_TRANSPARENT ;
@@ -5177,6 +5171,18 @@ bool dp_retrieve_lttpr_cap(struct dc_link *link) link->dc->debug.dpia_debug.bits.force_non_lttpr) link->lttpr_mode = LTTPR_MODE_NON_LTTPR;#endif +} + +bool dp_retrieve_lttpr_cap (struct dc_link *link) +{ +uint8_t lttpr_dpcd_data[8 ]; +enum dc_status status =DC_ERROR_UNEXPECTED ; +bool is_lttpr_present = false; + +memset (lttpr_dpcd_data,'\0' ,sizeof (lttpr_dpcd_data)); + +/* Logic to determine LTTPR mode*/ +determine_lttpr_mode (link);if (link->lttpr_mode ==LTTPR_MODE_NON_TRANSPARENT || link->lttpr_mode ==LTTPR_MODE_TRANSPARENT ) {/* By reading LTTPR capability, RX assumes that we will enable
@@ -5292,11 +5298,23 @@ static enum dc_status wa_try_to_wake_dprx(struct dc_link *link, uint64_t timeoutuint64_t time_taken_ms =0 ;enum dc_connection_type type = dc_connection_none; - status =core_link_read_dpcd ( - link, -DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV , - &dpcd_data, -sizeof (dpcd_data)); +determine_lttpr_mode (link); + +/* Issue an AUX read to test DPRX responsiveness. If LTTPR is supported the first read is expected to +* be to determine LTTPR capabilities. Otherwise trying to read power state should be an innocuous AUX read. +*/ +if (link->lttpr_mode ==LTTPR_MODE_NON_TRANSPARENT || link->lttpr_mode ==LTTPR_MODE_TRANSPARENT ) + status =core_link_read_dpcd ( + link, +DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV , + &dpcd_data, +sizeof (dpcd_data)); +else + status =core_link_read_dpcd ( + link, +DP_SET_POWER , + &dpcd_data, +sizeof (dpcd_data));if (status !=DC_OK ) { DC_LOG_WARNING("%s: Read DPCD LTTPR_CAP failed - try to toggle DPCD SET_POWER for %lld ms.",
Signature · 1 line
2.36.1
PATCH 14/16 drm/amd/display: Extend soc BB capabilitiy
In reply to Hamza MahfoozFrom: "Lei, Jun" <[email protected]>
[why]
Some parts are consuming dangerously close to maximum number of states supported when updating the BB (i.e. 8).
[how]
Change maximum stages from 9 to 20.
--- drivers/gpu/drm/amd/display/dc/dc.h | 1 + drivers/gpu/drm/amd/display/dc/dml/dc_features.h | 2 +- 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dc.h +1 -0
@@ -726,6 +726,7 @@ struct dc_debug_options {bool disable_dtb_ref_clk_switch;uint8_t psr_power_use_phy_fsm;enum dml_hostvm_override_opts dml_hostvm_override; +bool use_legacy_soc_bb_mechanism; };struct gpu_info_soc_bounding_box_v1_0 ;
drivers/gpu/drm/amd/display/dc/dml/dc_features.h +1 -1
@@ -29,7 +29,7 @@#define DC__PRESENT 1#define DC__PRESENT__1 1#define DC__NUM_DPP 4 -#define DC__VOLTAGE_STATES 9 +#define DC__VOLTAGE_STATES 20#define DC__NUM_DPP__4 1#define DC__NUM_DPP__0_PRESENT 1#define DC__NUM_DPP__1_PRESENT 1
Signature · 1 line
2.36.1
PATCH 15/16 drm/amd/display: Add HDMI member to DTO
In reply to Hamza MahfoozFrom: Chris Park <[email protected]>
[Why]
For Pixel Rate control, when on HDMI, HDMI DTO
should be selected instead of DP DTO.
[How]
Add HDMI member to dtbclk_dto_params, so it can be used tell apart HDMI and DP DTO in the future.
--- drivers/gpu/drm/amd/display/dc/inc/hw/dccg.h | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/amd/display/dc/inc/hw/dccg.h +1 -0
@@ -72,6 +72,7 @@ struct dtbclk_dto_params {int req_audio_dtbclk_khz;int num_odm_segments;int ref_dtbclk_khz; +bool is_hdmi; };struct dccg_funcs {
Signature · 1 line
2.36.1
PATCH 16/16 drm/amd/display: 3.2.189
In reply to Hamza MahfoozFrom: Aric Cyr <[email protected]>
This version brings along the following:
- DPP DTO fix
- Transient encoder fix
- Restrict the reading of LTTPR capabilities in LTTPR mode
- Increase maximum stages for BB
- Distinguish HDMI DTO from DP DTO
--- drivers/gpu/drm/amd/display/dc/dc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/amd/display/dc/dc.h +1 -1
@@ -47,7 +47,7 @@ struct aux_payload;struct set_config_cmd_payload ;struct dmub_notification ; -#define DC_VER "3.2.188" +#define DC_VER "3.2.189"#define MAX_SURFACES 3#define MAX_PLANES 6
Signature · 1 line
2.36.1
[Public]
Hi all,
This week this patchset was tested on the following systems:
HP Envy 360, with Ryzen 5 4500U
Lenovo Thinkpad T14s Gen2, with AMD Ryzen 5 5650U
Sapphire Pulse RX5700XT
Reference AMD RX6800
Engineering board with Ryzen 9 5900H
These systems were tested on the following display types:
eDP, (1080p 60hz [4500U, 5650U, 5900H])
VGA and DVI (1680x1050 60HZ [DP to VGA/DVI, USB-C to DVI/VGA]) DP/HDMI/USB-C (1440p 170hz, 4k 60hz, 4k 144hz [Includes USB-C to DP/HDMI adapters])
MST tested with Startech MST14DP123DP and 2x 4k 60Hz displays
DSC tested with Cable Matters 101075 (DP to 3x DP), and 201375 (USB-C to 3x DP) with 3x 4k60 displays
The testing is a mix of automated and manual tests. Manual testing includes (but is not limited to):
Changing display configurations and settings
Benchmark testing
Feature testing (Freesync, etc.)
Automated testing includes (but is not limited to):
Script testing (scripts to automate some of the manual checks) IGT testing
The patchset consists of the amd-staging-drm-next branch (Head commit - 79d15ef553971d39ae0df0c3ccf35905e4e4f1bf -> drm/amd/display: Add DCN32/321 version identifiers) with new patches added on top of it. This branch is used for both Ubuntu and Chrome OS testing (ChromeOS on a bi-weekly basis).
Tested on Ubuntu 22.04
Thank you,
Dan Wheeler
Technologist | AMD
SW Display
------------------------------------------------------------------------------------------------------------------
1 Commerce Valley Dr E, Thornhill, ON L3T 7X6
amd.com
-----Original Message-----
From: amd-gfx <[email protected]> On Behalf Of Hamza Mahfooz
Sent: June 3, 2022 4:12 PM
To: [email protected]
Cc: Wang, Chao-kai (Stylon) <[email protected]>; Li, Sun peng (Leo) <[email protected]>; Wentland, Harry <[email protected]>; Zhuo, Qingqing (Lillian) <[email protected]>; Siqueira, Rodrigo <[email protected]>; Li, Roman <[email protected]>; Chiu, Solomon <[email protected]>; Zuo, Jerry <[email protected]>; Pillai, Aurabindo <[email protected]>; Mahfooz, Hamza <[email protected]>; Lin, Wayne <[email protected]>; Lakha, Bhawanpreet <[email protected]>; Gutierrez, Agustin <[email protected]>; Kotarac, Pavle <[email protected]>
Subject: [PATCH 00/16] DC Patches May 30, 2022
* DPP DTO fix
* Transient encoder fix
* Restrict the reading of LTTPR capabilities in LTTPR mode
* Increase maximum stages for BB
* Distinguish HDMI DTO from DP DTO
* Optimized blank calculations
* More robust DP MST hotplug support
* eDP bug fix relating to ODM
* Revert a patch that caused a regression with DP
* min comp buffer size fix
* Make DP easier to debug
* Calculate the maximum OLED brightness correctly
* 3 plane MPO.
Anthony Koo (1):
drm/amd/display: [FW Promotion] Release 0.0.119.0
Aric Cyr (2):
drm/amd/display: 3.2.188
drm/amd/display: 3.2.189
Chris Park (1):
drm/amd/display: Add HDMI member to DTO
Duncan Ma (3):
drm/amd/display: Blank eDP on enable drv if odm enabled drm/amd/display: Correct min comp buffer size drm/amd/display: Fix dpp dto for disabled pipes
Gabe Teeger (1):
drm/amd/display: Update optimized blank calc and programming
Hansen Dsouza (1):
drm/amd/display: Enable 3 plane MPO
Jimmy Kizito (2):
drm/amd/display: Fix entry into transient encoder assignment mode. drm/amd/display: Avoid reading LTTPR caps in non-LTTPR mode.
Lei, Jun (1):
drm/amd/display: Extend soc BB capabilitiy
Nicholas Kazlauskas (1):
Revert "drm/amd/display: Pass the new context into disable OTG WA"
Roman Li (1):
drm/amd/display: Cap OLED brightness per max frame-average luminance
Wayne Lin (1):
drm/amd/display: Detect dpcd_rev when hotplug mst monitor
Wenjing Liu (1):
drm/amd/display: add DP sanity checks during enable stream
.../gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 8 +- .../display/amdgpu_dm/amdgpu_dm_mst_types.c | 38 ++++++++- .../display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c | 8 +- .../dc/clk_mgr/dcn315/dcn315_clk_mgr.c | 8 +- .../dc/clk_mgr/dcn316/dcn316_clk_mgr.c | 8 +- .../gpu/drm/amd/display/dc/core/dc_debug.c | 2 + drivers/gpu/drm/amd/display/dc/core/dc_link.c | 21 +++++ .../gpu/drm/amd/display/dc/core/dc_link_dp.c | 77 +++++++++++++------ .../drm/amd/display/dc/core/dc_link_enc_cfg.c | 45 ++++++++++- drivers/gpu/drm/amd/display/dc/dc.h | 4 +- drivers/gpu/drm/amd/display/dc/dc_link.h | 1 + .../drm/amd/display/dc/dcn20/dcn20_hwseq.c | 4 + .../display/dc/dcn31/dcn31_dio_link_encoder.c | 6 ++ .../gpu/drm/amd/display/dc/dcn31/dcn31_hubp.c | 2 +- .../drm/amd/display/dc/dcn31/dcn31_hwseq.c | 24 +++++- .../drm/amd/display/dc/dcn31/dcn31_resource.c | 1 - .../amd/display/dc/dcn315/dcn315_resource.c | 6 +- .../amd/display/dc/dcn316/dcn316_resource.c | 6 +- .../gpu/drm/amd/display/dc/dml/dc_features.h | 2 +- .../drm/amd/display/dc/dml/dcn31/dcn31_fpu.c | 3 +- .../dc/dml/dcn31/display_rq_dlg_calc_31.c | 16 +--- .../amd/display/dc/dml/display_mode_structs.h | 1 + .../drm/amd/display/dc/dml/display_mode_vba.h | 1 + .../gpu/drm/amd/display/dc/inc/core_status.h | 2 +- drivers/gpu/drm/amd/display/dc/inc/hw/dccg.h | 1 + .../gpu/drm/amd/display/dc/inc/link_enc_cfg.h | 7 ++ .../gpu/drm/amd/display/dmub/inc/dmub_cmd.h | 1 + 27 files changed, 234 insertions(+), 69 deletions(-)
--
2.36.1