ARM: imx: Switch Data Modul i.MX8M Mini eDM SBC to USB251x Hub driver
PATCH v4 1/1 ARM: imx: Switch Data Modul i.MX8M Mini eDM SBC to USB251x Hub driver
Replace the ad-hoc I2C register programming scripted in board environment with U-Boot DM driver.
Signed-off-by Marek Vasut <[email protected]>
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2: Use uclass_get_device_by_name()
V3: Reinstate the device-internal.h, needed for device_probe()
V4: Drop the device_probe() too
--- .../imx8mm_data_modul_edm_sbc.c | 9 +++++++++ configs/imx8mm_data_modul_edm_sbc_defconfig | 1 + include/configs/imx8mm_data_modul_edm_sbc.h | 20 ------------------- 3 files changed, 10 insertions(+), 20 deletions(-)
board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c +9 -0
@@ -9,6 +9,7 @@#include <asm/io.h> #include <asm/mach-imx/boot_mode.h> #include <dm.h> +#include <dm/device-internal.h> #include <i2c_eeprom.h> #include <malloc.h> #include <net.h>
@@ -104,7 +105,15 @@ int board_init(void)int board_late_init (void ) { +struct udevice *dev; +int ret; +setup_boot_device ();setup_mac_address (); + + ret =uclass_get_device_by_name (UCLASS_MISC ,"usb-hub@2c" , &dev); +if (ret) +printf ("Error bringing up USB hub (%d)\n" , ret); +return 0 ; }
configs/imx8mm_data_modul_edm_sbc_defconfig +1 -0
@@ -156,6 +156,7 @@ CONFIG_MXC_GPIO=y CONFIG_DM_I2C=y # CONFIG_INPUT is not set CONFIG_MISC=y +CONFIG_USB_HUB_USB251XB=y CONFIG_I2C_EEPROM=y CONFIG_SYS_I2C_EEPROM_ADDR=0x50 CONFIG_SUPPORT_EMMC_BOOT=y
include/configs/imx8mm_data_modul_edm_sbc.h +0 -20
@@ -71,7 +71,6 @@"mtd nor0=sf raw 0x0 0x1000000\0" \"dmo_preboot=" \"sf probe ; " /* Scan for SPI NOR, needed by DFU */ \ -"run dmo_usb_start_hub ; " \/* Attempt to start USB and Network console */ \"run dmo_usb_cdc_acm_start ; " \"run dmo_netconsole_start\0" \
@@ -91,25 +90,6 @@"setenv stdin ${stdin},usbacm ; " \"fi ; " \"fi\0" \ -"dmo_usb_start_hub=" \ -"i2c dev 1 ; " \ -/* Reset the USB USB */ \ -"gpio clear GPIO5_2 ; sleep 0.01 ; " /* t1 > 1us */ \ -"gpio set GPIO5_2 ; sleep 0.01 ; " /* t5 > 3us */ \ -/* Write chunks of descriptor into the USB HUB */ \ -"mw.l 0x7e1000 0x14042417 ; mw.l 0x7e1004 0x9b0bb325 ; " \ -"mw.l 0x7e1008 0x00000220 ; mw.l 0x7e100c 0x01320100 ; " \ -"mw.l 0x7e1010 0x00003232 ; mw.l 0x7e1014 0x4d000909 ; " \ -"i2c write 0x7e1000 0x2c 0x00 0x18 -s ; " \ -"mw.l 0x7e1000 0x6300690f ; mw.l 0x7e1004 0x6f007200 ; " \ -"mw.l 0x7e1008 0x68006300 ; mw.l 0x7e100c 0x70006900 ; " \ -"i2c write 0x7e1000 0x2c 0x18 0x10 -s ; " \ -"mw.l 0x7e1000 0x53005511 ; mw.l 0x7e1004 0x32004200 ; " \ -"mw.l 0x7e1008 0x31003500 ; mw.l 0x7e100c 0x42003400 ; " \ -"mw.l 0x7e1010 0x00006900 ; " \ -"i2c write 0x7e1000 0x2c 0x54 0x12 -s ; " \ -"mw.l 0x7e1000 0x00000101 ; " \ -"i2c write 0x7e1000 0x2c 0xff 0x2 -s\0" \"dmo_netconsole_start=" \"if test \"${dmo_netconsole_enabled}\" = \"true\" ; then " \"setenv autoload false && " \
Signature · 1 line
2.35.1
Quoted 8 lines · Marek Vasut
Replace the ad-hoc I2C register programming scripted in board environment with U-Boot DM driver.
Signed-off-by Marek Vasut <[email protected]>Cc Fabio Estevam <[email protected]>Cc Peng Fan <[email protected]>Cc Stefano Babic <[email protected]>
Reviewed-by Fabio Estevam <[email protected]>