Skip to contentSkip to conversation

net: dsa: qca8k: reduce mgmt ethernet timeout

PATCH RESEND Superseded Christian Marangi 2 participants 6 messages Jun 18, 2022 – Jun 21, 2022

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/3 net: dsa: qca8k: reduce mgmt ethernet timeout

The current mgmt ethernet timeout is set to 100ms. This value is too big and would slow down any mdio command in case the mgmt ethernet packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the master port that would cause the mgmt ethernet to not work temporarily.

---
 drivers/net/dsa/qca8k.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/dsa/qca8k.h +1 -1
index 04408e11402a..ec58d0e80a70 100644
@@ -15,7 +15,7 @@
 
 #define QCA8K_ETHERNET_MDIO_PRIORITY			7
 #define QCA8K_ETHERNET_PHY_PRIORITY			6
-#define QCA8K_ETHERNET_TIMEOUT				100
+#define QCA8K_ETHERNET_TIMEOUT				5
 
 #define QCA8K_NUM_PORTS					7
 #define QCA8K_NUM_CPU_PORTS				2
Signature · 1 line
2.36.1
#1 lore raw

PATCH RESEND 2/3 net: dsa: qca8k: change only max_frame_size of mac_frame_size_reg

Currently we overwrite the entire MAX_FRAME_SIZE reg instead of tweaking just the MAX_FRAME_SIZE value. Change this and update only the relevant bits.

---
 drivers/net/dsa/qca8k.c | 8 ++++++--
 drivers/net/dsa/qca8k.h | 3 ++-
 2 files changed, 8 insertions(+), 3 deletions(-)
drivers/net/dsa/qca8k.c +6 -2
index 2727d3169c25..eaaf80f96fa9 100644
@@ -2345,7 +2345,9 @@ qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 		return 0;
 
 	/* Include L2 header / FCS length */
-	return qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, new_mtu + ETH_HLEN + ETH_FCS_LEN);
+	return regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
+				  QCA8K_MAX_FRAME_SIZE_MASK,
+				  new_mtu + ETH_HLEN + ETH_FCS_LEN);
 }
 
 static int
@@ -3015,7 +3017,9 @@ qca8k_setup(struct dsa_switch *ds)
 	}
 
 	/* Setup our port MTUs to match power on defaults */
-	ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN);
+	ret = regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
+				 QCA8K_MAX_FRAME_SIZE_MASK,
+				 ETH_FRAME_LEN + ETH_FCS_LEN);
 	if (ret)
 		dev_warn(priv->dev, "failed setting MTU settings");
 
drivers/net/dsa/qca8k.h +2 -1
index ec58d0e80a70..1d0c383a95e7 100644
@@ -87,7 +87,8 @@
 #define   QCA8K_MDIO_MASTER_MAX_REG			32
 #define QCA8K_GOL_MAC_ADDR0				0x60
 #define QCA8K_GOL_MAC_ADDR1				0x64
-#define QCA8K_MAX_FRAME_SIZE				0x78
+#define QCA8K_MAX_FRAME_SIZE_REG			0x78
+#define   QCA8K_MAX_FRAME_SIZE_MASK			GENMASK(13, 0)
 #define QCA8K_REG_PORT_STATUS(_i)			(0x07c + (_i) * 4)
 #define   QCA8K_PORT_STATUS_SPEED			GENMASK(1, 0)
 #define   QCA8K_PORT_STATUS_SPEED_10			0
Signature · 1 line
2.36.1
#2 lore raw

PATCH RESEND 3/3 net: dsa: qca8k: reset cpu port on MTU change

In reply to Christian Marangi

It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required.

To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied.

Fixes f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
---
 drivers/net/dsa/qca8k.c | 26 +++++++++++++++++++++++---
 1 file changed, 23 insertions(+), 3 deletions(-)
drivers/net/dsa/qca8k.c +23 -3
index eaaf80f96fa9..0b92b9d5954a 100644
@@ -2334,6 +2334,7 @@ static int
 qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct qca8k_priv *priv = ds->priv;
+	int ret;
 
 	/* We have only have a general MTU setting.
 	 * DSA always set the CPU port's MTU to the largest MTU of the slave
@@ -2344,10 +2345,29 @@ qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
+	/* To change the MAX_FRAME_SIZE the cpu ports must be off or
+	 * the switch panics.
+	 * Turn off both cpu ports before applying the new value to prevent
+	 * this.
+	 */
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 0);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 0);
+
 	/* Include L2 header / FCS length */
-	return regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
-				  QCA8K_MAX_FRAME_SIZE_MASK,
-				  new_mtu + ETH_HLEN + ETH_FCS_LEN);
+	ret = regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
+				 QCA8K_MAX_FRAME_SIZE_MASK,
+				 new_mtu + ETH_HLEN + ETH_FCS_LEN);
+
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 1);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 1);
+
+	return ret;
 }
 
 static int
Signature · 1 line
2.36.1
maintainer
#3 lore raw

Re: [RESEND net-next PATCH 3/3] net: dsa: qca8k: reset cpu port on MTU change

Quoted 9 lines · On Sat, 18 Jun 2022 09:26:50 +0200 Christian Marangi wrote:

It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required.

Quoted 5 lines

To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied.

Fixes f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")

It reads like this patch should be backported to 5.10 and 5.15 stable branches. While patches 1 and 2 are cleanups. In which case you should reports just patch 3 against net/master first, we'll send it to Linus at the end of the week and then you can send the cleanups on top for -next.

One extra question below.

Quoted 22 lines
drivers/net/dsa/qca8k.c +7 -0
index eaaf80f96fa9..0b92b9d5954a 100644
@@ -2334,6 +2334,7 @@ static int
 qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct qca8k_priv *priv = ds->priv;
+	int ret;
 
 	/* We have only have a general MTU setting.
 	 * DSA always set the CPU port's MTU to the largest MTU of the slave
@@ -2344,10 +2345,29 @@ qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
+	/* To change the MAX_FRAME_SIZE the cpu ports must be off or
+	 * the switch panics.
+	 * Turn off both cpu ports before applying the new value to prevent
+	 * this.
+	 */
+	if (priv->port_enabled_map & BIT(0))

drivers/net/dsa/qca8k.c qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) · line 2360

Quoted 10 lines
drivers/net/dsa/qca8k.c +6 -3
+		qca8k_port_set_status(priv, 0, 0);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 0);
+
 	/* Include L2 header / FCS length */
-	return regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
-				  QCA8K_MAX_FRAME_SIZE_MASK,
-				  new_mtu + ETH_HLEN + ETH_FCS_LEN);
+	ret = regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,

Why care about the return code of this regmap access but not the ones inside the *port_set_status() calls?

Quoted 13 lines
drivers/net/dsa/qca8k.c +10 -0
+				 QCA8K_MAX_FRAME_SIZE_MASK,
+				 new_mtu + ETH_HLEN + ETH_FCS_LEN);
+
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 1);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 1);
+
+	return ret;
 }
 
 static int
#4 lore raw

Re: [RESEND net-next PATCH 3/3] net: dsa: qca8k: reset cpu port on MTU change

Quoted 13 lines · Jakub Kicinski
Quoted 12 lines · On Sat, 18 Jun 2022 09:26:50 +0200 Christian Marangi wrote:

It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required.

To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied.

Quoted 8 lines
Quoted 2 lines
Fixes f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")

It reads like this patch should be backported to 5.10 and 5.15 stable branches. While patches 1 and 2 are cleanups. In which case you should reports just patch 3 against net/master first, we'll send it to Linus at the end of the week and then you can send the cleanups on top for -next.

Ok will split this series.

Quoted 29 lines

One extra question below.

Quoted 27 lines
drivers/net/dsa/qca8k.c +12 -0
index eaaf80f96fa9..0b92b9d5954a 100644
@@ -2334,6 +2334,7 @@ static int
 qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct qca8k_priv *priv = ds->priv;
+	int ret;
 
 	/* We have only have a general MTU setting.
 	 * DSA always set the CPU port's MTU to the largest MTU of the slave
@@ -2344,10 +2345,29 @@ qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
+	/* To change the MAX_FRAME_SIZE the cpu ports must be off or
+	 * the switch panics.
+	 * Turn off both cpu ports before applying the new value to prevent
+	 * this.
+	 */
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 0);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 0);
+
Quoted 9 lines

drivers/net/dsa/qca8k.c qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) · line 2360

Quoted 5 lines
drivers/net/dsa/qca8k.c +1 -3
 	/* Include L2 header / FCS length */
-	return regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
-				  QCA8K_MAX_FRAME_SIZE_MASK,
-				  new_mtu + ETH_HLEN + ETH_FCS_LEN);
+	ret = regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,

Why care about the return code of this regmap access but not the ones inside the *port_set_status() calls?

No reason just following old bad behaviour done in other function where qca8k_port_set_status is used. Will send v2 with the error handled.

Quoted 13 lines
Quoted 13 lines
drivers/net/dsa/qca8k.c +10 -0
+				 QCA8K_MAX_FRAME_SIZE_MASK,
+				 new_mtu + ETH_HLEN + ETH_FCS_LEN);
+
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 1);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 1);
+
+	return ret;
 }
 
 static int
Signature · 1 line
	Ansuel
#5 lore raw

Re: [RESEND net-next PATCH 3/3] net: dsa: qca8k: reset cpu port on MTU change

Quoted 64 lines · Christian Marangi
Quoted 13 lines · Jakub Kicinski
Quoted 12 lines · On Sat, 18 Jun 2022 09:26:50 +0200 Christian Marangi wrote:

It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required.

To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied.

Quoted 8 lines
Quoted 2 lines
Fixes f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")

It reads like this patch should be backported to 5.10 and 5.15 stable branches. While patches 1 and 2 are cleanups. In which case you should reports just patch 3 against net/master first, we'll send it to Linus at the end of the week and then you can send the cleanups on top for -next.

Ok will split this series.

Quoted 29 lines

One extra question below.

Quoted 27 lines
drivers/net/dsa/qca8k.c +12 -0
index eaaf80f96fa9..0b92b9d5954a 100644
@@ -2334,6 +2334,7 @@ static int
 qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct qca8k_priv *priv = ds->priv;
+	int ret;
 
 	/* We have only have a general MTU setting.
 	 * DSA always set the CPU port's MTU to the largest MTU of the slave
@@ -2344,10 +2345,29 @@ qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
+	/* To change the MAX_FRAME_SIZE the cpu ports must be off or
+	 * the switch panics.
+	 * Turn off both cpu ports before applying the new value to prevent
+	 * this.
+	 */
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 0);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 0);
+
Quoted 9 lines

drivers/net/dsa/qca8k.c qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) · line 2360

Quoted 5 lines
drivers/net/dsa/qca8k.c +1 -3
 	/* Include L2 header / FCS length */
-	return regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,
-				  QCA8K_MAX_FRAME_SIZE_MASK,
-				  new_mtu + ETH_HLEN + ETH_FCS_LEN);
+	ret = regmap_update_bits(priv->regmap, QCA8K_MAX_FRAME_SIZE_REG,

Why care about the return code of this regmap access but not the ones inside the *port_set_status() calls?

Quoted 3 lines

No reason just following old bad behaviour done in other function where qca8k_port_set_status is used. Will send v2 with the error handled.

Actually now that i checked, the qca8k_port_set_status is void... So it would require an additional change to that function. Will make it part of the net-next series...

Quoted 16 lines
Quoted 13 lines
Quoted 13 lines
drivers/net/dsa/qca8k.c +10 -0
+				 QCA8K_MAX_FRAME_SIZE_MASK,
+				 new_mtu + ETH_HLEN + ETH_FCS_LEN);
+
+	if (priv->port_enabled_map & BIT(0))
+		qca8k_port_set_status(priv, 0, 1);
+
+	if (priv->port_enabled_map & BIT(6))
+		qca8k_port_set_status(priv, 6, 1);
+
+	return ret;
 }
 
 static int
Signature · 1 line
	Ansuel
Signature · 1 line
	Ansuel