phy: qcom-qmp-pcie: make pipe clock rate configurable
PATCH v4 1/3 phy: qcom-qmp-pcie: make pipe clock rate configurable
IPQ8074 Gen3 PCIe PHY uses 250MHz as the pipe clock rate instead of 125MHz like every other PCIe QMP PHY does, so make it configurable as part of the qmp_phy_cfg.
---
Changes in v4:
* Set 125MHz as the default if not set in qmp_phy_cfg
--- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-)
drivers/phy/qualcomm/phy-qcom-qmp-pcie.c +12 -2
@@ -1284,6 +1284,9 @@ struct qmp_phy_cfg {/* true, if PHY has secondary tx/rx lanes to be configured */ bool is_dual_lane_phy; + +/* QMP PHY pipe clock interface rate */ +unsigned long pipe_clock_rate; };/**
@@ -2121,8 +2124,15 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) init.ops = &clk_fixed_rate_ops; -/* controllers using QMP phys use 125MHz pipe clock interface */ - fixed->fixed_rate =125000000 ; +/* +* Controllers using QMP PHY-s use 125MHz pipe clock interface +* unless other frequency is specified in the PHY config. +*/ +if (qmp->phys[0 ]->cfg->pipe_clock_rate) + fixed->fixed_rate = qmp->phys[0 ]->cfg->pipe_clock_rate; +else + fixed->fixed_rate =125000000 ; + fixed->hw.init = &init; ret =devm_clk_hw_register (qmp->dev, &fixed->hw);
Signature · 1 line
2.36.1
PATCH v4 2/3 dt-bindings: phy: qcom,qmp: add IPQ8074 PCIe Gen3 PHY binding
IPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, document the bindings for the Gen3 one.
--- Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml +2 -0
@@ -19,6 +19,7 @@ properties: enum: - qcom,ipq6018-qmp-pcie-phy - qcom,ipq6018-qmp-usb3-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy - qcom,ipq8074-qmp-usb3-phy - qcom,msm8996-qmp-pcie-phy
@@ -312,6 +313,7 @@ allOf: contains: enum: - qcom,ipq6018-qmp-pcie-phy + - qcom,ipq8074-qmp-gen3-pcie-phy - qcom,ipq8074-qmp-pcie-phy then: properties:
Signature · 1 line
2.36.1
PATCH v4 3/3 phy: qcom-qmp-pcie: add IPQ8074 PCIe Gen3 QMP PHY support
In reply to Robert MarkoIPQ8074 has 2 different single lane PCIe PHY-s, one Gen2 and one Gen3. Gen2 one is already supported, so add the support for the Gen3 one. It uses the same register layout as IPQ6018.
---
Changes in v3:
* Remove parsing QMP pipe clock rate from DT, and instead use the rate as set in the PHY config
Changes in v2:
* Rebase onto next-20220621 to apply on the refactored driver
* Remove non existant has_phy_com_ctrl and has_lane_rst
--- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 160 +++++++++++++++++++++++ 1 file changed, 160 insertions(+)
drivers/phy/qualcomm/phy-qcom-qmp-pcie.c +160 -0
@@ -450,6 +450,133 @@ static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = { QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3), }; +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_serdes_tbl[] = { +QMP_PHY_INIT_CFG (QSERDES_PLL_BIAS_EN_CLKBUFLR_EN ,0x18 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_BIAS_EN_CTRL_BY_PSM ,0x01 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_SELECT ,0x31 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_PLL_IVCO ,0x0f ), +QMP_PHY_INIT_CFG (QSERDES_PLL_BG_TRIM ,0x0f ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CMN_CONFIG ,0x06 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_LOCK_CMP_EN ,0x42 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_RESETSM_CNTRL ,0x20 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SVS_MODE_CLK_SEL ,0x01 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE_MAP ,0x04 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SVS_MODE_CLK_SEL ,0x05 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE_TIMER1 ,0xff ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE_TIMER2 ,0x3f ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CORE_CLK_EN ,0x30 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_HSCLK_SEL ,0x21 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DEC_START_MODE0 ,0x82 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START3_MODE0 ,0x03 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START2_MODE0 ,0x355 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START1_MODE0 ,0x35555 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_LOCK_CMP2_MODE0 ,0x1a ), +QMP_PHY_INIT_CFG (QSERDES_PLL_LOCK_CMP1_MODE0 ,0x1a0a ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CP_CTRL_MODE0 ,0xb ), +QMP_PHY_INIT_CFG (QSERDES_PLL_PLL_RCTRL_MODE0 ,0x16 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_PLL_CCTRL_MODE0 ,0x28 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_INTEGLOOP_GAIN1_MODE0 ,0x0 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_INTEGLOOP_GAIN0_MODE0 ,0x40 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE2_MODE0 ,0x02 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE1_MODE0 ,0x24 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SVS_MODE_CLK_SEL ,0x05 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CORE_CLK_EN ,0x20 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CORECLK_DIV ,0xa ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_SELECT ,0x32 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SYS_CLK_CTRL ,0x02 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SYSCLK_BUF_ENABLE ,0x07 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SYSCLK_EN_SEL ,0x08 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_BG_TIMER ,0xa ), +QMP_PHY_INIT_CFG (QSERDES_PLL_HSCLK_SEL ,0x1 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DEC_START_MODE1 ,0x68 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START3_MODE1 ,0x2 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START2_MODE1 ,0x2aa ), +QMP_PHY_INIT_CFG (QSERDES_PLL_DIV_FRAC_START1_MODE1 ,0x2aaab ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_ENABLE1 ,0x90 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_LOCK_CMP2_MODE1 ,0x34 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_LOCK_CMP1_MODE1 ,0x3414 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CP_CTRL_MODE1 ,0x0b ), +QMP_PHY_INIT_CFG (QSERDES_PLL_PLL_RCTRL_MODE1 ,0x16 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_PLL_CCTRL_MODE1 ,0x28 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_INTEGLOOP_GAIN1_MODE1 ,0x0 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_INTEGLOOP_GAIN0_MODE1 ,0x40 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE2_MODE1 ,0x03 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_VCO_TUNE1_MODE1 ,0xb4 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_SVS_MODE_CLK_SEL ,0x05 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CORE_CLK_EN ,0x0 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CORECLK_DIV_MODE1 ,0x08 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_EP_DIV_MODE0 ,0x19 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_EP_DIV_MODE1 ,0x28 ), +QMP_PHY_INIT_CFG (QSERDES_PLL_CLK_ENABLE1 ,0x90 ), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_tx_tbl[] = { +QMP_PHY_INIT_CFG (QSERDES_TX0_RES_CODE_LANE_OFFSET_TX ,0x02 ), +QMP_PHY_INIT_CFG (QSERDES_TX0_RCV_DETECT_LVL_2 ,0x12 ), +QMP_PHY_INIT_CFG (QSERDES_TX0_HIGHZ_DRVR_EN ,0x10 ), +QMP_PHY_INIT_CFG (QSERDES_TX0_LANE_MODE_1 ,0x06 ), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_rx_tbl[] = { +QMP_PHY_INIT_CFG (QSERDES_RX0_SIGDET_CNTRL ,0x03 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_SIGDET_ENABLES ,0x1c ), +QMP_PHY_INIT_CFG (QSERDES_RX0_SIGDET_DEGLITCH_CNTRL ,0x14 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL2 ,0xe ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL3 ,0x4 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_EQU_ADAPTOR_CNTRL4 ,0x1b ), +QMP_PHY_INIT_CFG (QSERDES_RX0_DFE_EN_TIMER ,0x04 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_UCDR_SO_SATURATION_AND_ENABLE ,0x7f ), +QMP_PHY_INIT_CFG (QSERDES_RX0_UCDR_PI_CONTROLS ,0x70 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_EQ_OFFSET_ADAPTOR_CNTRL1 ,0x73 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_OFFSET_ADAPTOR_CNTRL2 ,0x80 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_10_LOW ,0x00 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_10_HIGH ,0x02 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_10_HIGH2 ,0xc8 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_10_HIGH3 ,0x09 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_10_HIGH4 ,0xb1 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_01_LOW ,0x01 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_01_HIGH ,0x02 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_01_HIGH2 ,0xc8 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_01_HIGH3 ,0x09 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_01_HIGH4 ,0xb1 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_00_LOW ,0xf0 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_00_HIGH ,0x2 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_00_HIGH2 ,0x2f ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_00_HIGH3 ,0xd3 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_MODE_00_HIGH4 ,0x40 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_IDAC_TSETTLE_HIGH ,0x00 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_RX_IDAC_TSETTLE_LOW ,0xc0 ), +QMP_PHY_INIT_CFG (QSERDES_RX0_UCDR_FO_GAIN ,0x0c ), +QMP_PHY_INIT_CFG (QSERDES_RX0_UCDR_SO_GAIN ,0x02 ), +}; + +static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_pcs_tbl[] = { +QMP_PHY_INIT_CFG (PCS_COM_FLL_CNTRL2 ,0x83 ), +QMP_PHY_INIT_CFG (PCS_COM_FLL_CNT_VAL_L ,0x9 ), +QMP_PHY_INIT_CFG (PCS_COM_FLL_CNT_VAL_H_TOL ,0x42 ), +QMP_PHY_INIT_CFG (PCS_COM_FLL_MAN_CODE ,0x40 ), +QMP_PHY_INIT_CFG (PCS_COM_FLL_CNTRL1 ,0x01 ), +QMP_PHY_INIT_CFG (PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_H ,0x0 ), +QMP_PHY_INIT_CFG (PCS_COM_P2U3_WAKEUP_DLY_TIME_AUXCLK_L ,0x1 ), +QMP_PHY_INIT_CFG (PCS_PCIE_OSC_DTCT_ACTIONS ,0x0 ), +QMP_PHY_INIT_CFG (PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H ,0x00 ), +QMP_PHY_INIT_CFG (PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L ,0x01 ), +QMP_PHY_INIT_CFG (PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H ,0x00 ), +QMP_PHY_INIT_CFG (PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L ,0x01 ), +QMP_PHY_INIT_CFG (PCS_PCIE_EQ_CONFIG1 ,0x11 ), +QMP_PHY_INIT_CFG (PCS_PCIE_EQ_CONFIG2 ,0xb ), +QMP_PHY_INIT_CFG (PCS_PCIE_POWER_STATE_CONFIG4 ,0x07 ), +QMP_PHY_INIT_CFG (PCS_PCIE_OSC_DTCT_CONFIG2 ,0x52 ), +QMP_PHY_INIT_CFG (PCS_PCIE_OSC_DTCT_MODE2_CONFIG2 ,0x50 ), +QMP_PHY_INIT_CFG (PCS_PCIE_OSC_DTCT_MODE2_CONFIG4 ,0x1a ), +QMP_PHY_INIT_CFG (PCS_PCIE_OSC_DTCT_MODE2_CONFIG5 ,0x6 ), +QMP_PHY_INIT_CFG (PCS_COM_G12S1_TXDEEMPH_M3P5DB ,0x10 ), +QMP_PHY_INIT_CFG (PCS_PCIE_ENDPOINT_REFCLK_DRIVE ,0xc1 ), +QMP_PHY_INIT_CFG (PCS_COM_RX_DCC_CAL_CONFIG ,0x01 ), +QMP_PHY_INIT_CFG (PCS_COM_RX_SIGDET_LVL ,0xaa ), +QMP_PHY_INIT_CFG (PCS_COM_REFGEN_REQ_CONFIG1 ,0x0d ), +}; +static const struct qmp_phy_init_tbl sdm845_qmp_pcie_serdes_tbl[] = {QMP_PHY_INIT_CFG (QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN ,0x14 ),QMP_PHY_INIT_CFG (QSERDES_V3_COM_CLK_SELECT ,0x30 ),
@@ -1424,6 +1551,36 @@ static const struct qmp_phy_cfg ipq8074_pciephy_cfg = { .pwrdn_delay_max = 1005, /* us */ }; +static const struct qmp_phy_cfg ipq8074_pciephy_gen3_cfg = { + .type =PHY_TYPE_PCIE , + .nlanes =1 , + + .serdes_tbl = ipq8074_pcie_gen3_serdes_tbl, + .serdes_tbl_num =ARRAY_SIZE (ipq8074_pcie_gen3_serdes_tbl), + .tx_tbl = ipq8074_pcie_gen3_tx_tbl, + .tx_tbl_num =ARRAY_SIZE (ipq8074_pcie_gen3_tx_tbl), + .rx_tbl = ipq8074_pcie_gen3_rx_tbl, + .rx_tbl_num =ARRAY_SIZE (ipq8074_pcie_gen3_rx_tbl), + .pcs_tbl = ipq8074_pcie_gen3_pcs_tbl, + .pcs_tbl_num =ARRAY_SIZE (ipq8074_pcie_gen3_pcs_tbl), + .clk_list = ipq8074_pciephy_clk_l, + .num_clks =ARRAY_SIZE (ipq8074_pciephy_clk_l), + .reset_list = ipq8074_pciephy_reset_l, + .num_resets =ARRAY_SIZE (ipq8074_pciephy_reset_l), + .vreg_list =NULL , + .num_vregs =0 , + .regs = ipq_pciephy_gen3_regs_layout, + + .start_ctrl =SERDES_START |PCS_START , + .pwrdn_ctrl =SW_PWRDN |REFCLK_DRV_DSBL , + + .has_pwrdn_delay = true, + .pwrdn_delay_min =995 ,/* us */ + .pwrdn_delay_max =1005 ,/* us */ + + .pipe_clock_rate =250000000 , +}; +static const struct qmp_phy_cfg ipq6018_pciephy_cfg = { .type =PHY_TYPE_PCIE , .nlanes =1 ,
@@ -2265,6 +2422,9 @@ static const struct of_device_id qcom_qmp_phy_pcie_of_match_table[] = { }, { .compatible = "qcom,ipq8074-qmp-pcie-phy", .data = &ipq8074_pciephy_cfg, + }, { + .compatible = "qcom,ipq8074-qmp-gen3-pcie-phy", + .data = &ipq8074_pciephy_gen3_cfg, }, { .compatible = "qcom,ipq6018-qmp-pcie-phy", .data = &ipq6018_pciephy_cfg,
Signature · 1 line
2.36.1
Quoted 6 lines · Robert Marko
IPQ8074 Gen3 PCIe PHY uses 250MHz as the pipe clock rate instead of 125MHz like every other PCIe QMP PHY does, so make it configurable as part of the
qmp_phy_cfg.Signed-off-by Robert Marko <[email protected]>
Quoted 7 lines
---
Changes in v4:
* Set 125MHz as the default if not set inqmp_phy_cfg--- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-)
Signature · 2 lines
With best wishes Dmitry
Quoted 3 lines · Robert Marko
IPQ8074 Gen3 PCIe PHY uses 250MHz as the pipe clock rate instead of 125MHz like every other PCIe QMP PHY does, so make it configurable as part of the
qmp_phy_cfg.
Applied, thanks
Signature · 6 lines
~Vinod -- linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy