Skip to contentSkip to conversation

pmic: pca9450: Add optional SD_VSEL GPIO for LDO5

PATCH In review Frieder Schrempf 2 participants 4 messages Jun 27, 2022 – Jun 28, 2022

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 pmic: pca9450: Add optional SD_VSEL GPIO for LDO5

From: Frieder Schrempf <[email protected]>

LDO5 has two separate control registers. LDO5CTRL_L is used if the input signal SD_VSEL is low and LDO5CTRL_H if it is high. The current driver implementation only uses LDO5CTRL_H. To make this work on boards that have SD_VSEL connected to a GPIO, we add support for specifying an optional GPIO and setting it to high at probe time.

In the future we might also want to add support for boards that have SD_VSEL set to a fixed low level. In this case we need to change the driver to be able to use the LDO5CTRL_L register.

This is a port of the same change in the Linux kernel:
8c67a11bae88 ("regulator: pca9450: Add SD_VSEL GPIO for LDO5")

---
Changes in v2:
* Add Fabio's R-b (Thanks!)
* Use CONFIG_IS_ENABLED() instead of IS_ENABLED(CONFIG_*) to properly detect the options for SPL.

---
 drivers/power/pmic/pca9450.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/power/pmic/pca9450.c +27 -0
index 116ac49a8db..a186edc08da 100644
@@ -7,9 +7,12 @@
 #include <fdtdec.h>
 #include <errno.h>
 #include <dm.h>
+#include <dm/device_compat.h>
 #include <i2c.h>
+#include <linux/err.h>
 #include <log.h>
 #include <asm/global_data.h>
+#include <asm-generic/gpio.h>
 #include <power/pmic.h>
 #include <power/regulator.h>
 #include <power/pca9450.h>
@@ -26,6 +29,10 @@ static const struct pmic_child_info pmic_children_info[] = {
 	{ },
 };
 
+struct pca9450_priv {
+	struct gpio_desc *sd_vsel_gpio;
+};
+
 static int pca9450_reg_count(struct udevice *dev)
 {
 	return PCA9450_REG_NUM;
@@ -76,6 +83,24 @@ static int pca9450_bind(struct udevice *dev)
 	return 0;
 }
 
+static int pca9450_probe(struct udevice *dev)
+{
+	struct pca9450_priv *priv = dev_get_priv(dev);
+	int ret = 0;
+
+	if (CONFIG_IS_ENABLED(DM_GPIO) && CONFIG_IS_ENABLED(DM_REGULATOR_PCA9450)) {
+		priv->sd_vsel_gpio = devm_gpiod_get_optional(dev, "sd-vsel",
+							     GPIOD_IS_OUT |
+							     GPIOD_IS_OUT_ACTIVE);
+		if (IS_ERR(priv->sd_vsel_gpio)) {
+			ret = PTR_ERR(priv->sd_vsel_gpio);
+			dev_err(dev, "Failed to request SD_VSEL GPIO: %d\n", ret);
+		}
+	}
+
+	return ret;
+}
+
 static struct dm_pmic_ops pca9450_ops = {
 	.reg_count = pca9450_reg_count,
 	.read = pca9450_read,
@@ -94,5 +119,7 @@ U_BOOT_DRIVER(pmic_pca9450) = {
 	.id = UCLASS_PMIC,
 	.of_match = pca9450_ids,
 	.bind = pca9450_bind,
+	.probe = pca9450_probe,
 	.ops = &pca9450_ops,
+	.priv_auto = sizeof(struct pca9450_priv),
 };
Signature · 1 line
2.36.1
#1 lore raw

PATCH v2 2/2 imx: kontron-sl-mx8mm: Enable PCA9450 regulator driver and fix SD card access

From: Frieder Schrempf <[email protected]>

Currently accessing the SD card on USDHC2 fails with:

=> mmc dev 1
Card did not respond to voltage select! : -110

This is due to the fact that UHS modes are enabled in the defconfig and the devicetree, but the referenced LDO5 regulator (reg_nvcc_sd) is not available to switch the data lines from 3.3V to 1.8V mode.

By enabling the regulator driver the vqmmc-supply is now available and the SD card works also in high speed modes:

=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Please note that the board has a GPIO connected to the SD_VSEL signal of the PMIC. As the driver uses the LDO5CTRL_H register to set the voltage, we need to make sure that this GPIO (GPIO01_IO4) is set to a high level.

---
Changes in v2:
* Add Fabio's R-b (Thanks!)

---
 configs/kontron-sl-mx8mm_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/kontron-sl-mx8mm_defconfig +1 -0
index 2e9d52522b2..727f99f0063 100644
@@ -99,6 +99,7 @@ CONFIG_DM_PMIC=y
 CONFIG_DM_PMIC_PCA9450=y
 CONFIG_SPL_DM_PMIC_PCA9450=y
 CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PCA9450=y
 CONFIG_DM_RTC=y
 CONFIG_RTC_RV8803=y
 CONFIG_CONS_INDEX=2
Signature · 1 line
2.36.1
Tested-by on v2 2/2
#2 lore raw

Re: [PATCH v2 2/2] imx: kontron-sl-mx8mm: Enable PCA9450 regulator driver and fix SD card access

Quoted 19 lines · Frieder Schrempf

From: Frieder Schrempf <[email protected]>

Currently accessing the SD card on USDHC2 fails with:

=> mmc dev 1
Card did not respond to voltage select! : -110

This is due to the fact that UHS modes are enabled in the defconfig and the devicetree, but the referenced LDO5 regulator (reg_nvcc_sd) is not available to switch the data lines from 3.3V to 1.8V mode.

By enabling the regulator driver the vqmmc-supply is now available and the SD card works also in high speed modes:

=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Quoted 7 lines

Please note that the board has a GPIO connected to the SD_VSEL signal of the PMIC. As the driver uses the LDO5CTRL_H register to set the voltage, we need to make sure that this GPIO (GPIO01_IO4) is set to a high level.

Tested-by on v2 1/2
#3 lore raw
In reply to Frieder Schrempf
Quoted 13 lines · Frieder Schrempf

From: Frieder Schrempf <[email protected]>

LDO5 has two separate control registers. LDO5CTRL_L is used if the input signal SD_VSEL is low and LDO5CTRL_H if it is high. The current driver implementation only uses LDO5CTRL_H. To make this work on boards that have SD_VSEL connected to a GPIO, we add support for specifying an optional GPIO and setting it to high at probe time.

In the future we might also want to add support for boards that have SD_VSEL set to a fixed low level. In this case we need to change the driver to be able to use the LDO5CTRL_L register.

Quoted 5 lines

This is a port of the same change in the Linux kernel:
8c67a11bae88 ("regulator: pca9450: Add SD_VSEL GPIO for LDO5")

Tom,

Please apply these patches to 2022.07.

Thanks