rk3399 after reboot mmc1 is inaceessible
Hello,
after rebooting rk3399 Pinebook Pro mmc1 is no longer accessible from u-boot, and video is not working, only cold boot works.
This is not a problem anymore when Linux is loaded from another device.
Any idea how to debug this?
Thanks
Michal
U-Boot TPL 2022.07-rc5 (May 16 2022 - 12:00:00)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2022.07-rc5 (May 16 2022 - 12:00:00 +0000) Trying to boot from MMC1
NOTICE: BL31: v2.6(debug): NOTICE: BL31: Built : 14:50:40, Jul 1 2022 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 287 INFO: plat_rockchip_pmu_init(1624): pd status 3e INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9
U-Boot 2022.07-rc5 (May 16 2022 - 00:00:00 +0000)
SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 Pinebook Pro DRAM: 3.9 GiB PMIC: RK808 Core: 317 devices, 34 uclasses, devicetree: separate MMC: mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: vidconsole Err: vidconsole Model: Pine64 Pinebook Pro Net: No ethernet found.
starting USB...
Bus usb@fe380000: ehci_generic usb@fe380000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: ehci_generic usb@fe3c0000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3e0000: USB OHCI 1.0
Bus usb@fe800000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe900000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3e0000 for devices... 4 USB Device(s) found scanning bus usb@fe800000 for devices... 1 USB Device(s) found scanning bus usb@fe900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
** Invalid partition 3 **
Couldn't find partition mmc 1:3
** Invalid partition 4 **
Couldn't find partition mmc 1:4
Scanning mmc 1:1...
BootOrder not defined
EFI boot manager: Cannot load any image
Found EFI removable media binary efi/boot/bootaa64.efi
857968 bytes read in 96 ms (8.5 MiB/s)
Booting /efi\boot\bootaa64.efi
U-Boot TPL 2022.07-rc5 (May 16 2022 - 12:00:00)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2022.07-rc5 (May 16 2022 - 12:00:00 +0000) Trying to boot from MMC1
NOTICE: BL31: v2.6(debug): NOTICE: BL31: Built : 14:50:40, Jul 1 2022 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 287 INFO: plat_rockchip_pmu_init(1624): pd status 3e INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9
U-Boot 2022.07-rc5 (May 16 2022 - 00:00:00 +0000)
SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 Pinebook Pro DRAM: 3.9 GiB PMIC: RK808 Core: 317 devices, 34 uclasses, devicetree: separate MMC: mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: vidconsole Err: vidconsole Model: Pine64 Pinebook Pro Net: No ethernet found.
starting USB...
Bus usb@fe380000: ehci_generic usb@fe380000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: ehci_generic usb@fe3c0000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3e0000: USB OHCI 1.0
Bus usb@fe800000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe900000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3e0000 for devices... 4 USB Device(s) found scanning bus usb@fe800000 for devices... 1 USB Device(s) found scanning bus usb@fe900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
U-Boot TPL 2022.07-rc6-00020-g049b3b43be-dirty (Jul 09 2022 - 12:52:27) Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2022.07-rc6-00020-g049b3b43be-dirty (Jul 09 2022 - 12:52:27 +0200)
Trying to boot from MMC2
Buswidth = 0, clock: 0
Buswidth = 1, clock: 0
Buswidth = 1, clock: 400000
Sending CMD0
Sending CMD8
Sending CMD55
Sending CMD41
Sending CMD55
Sending CMD41
Sending CMD55
Sending CMD41
Sending CMD55
Sending CMD41
Sending CMD55
Sending CMD41
Sending CMD55
Sending CMD41
Sending CMD2
Sending CMD3
Sending CMD9
Sending CMD7
Sending CMD55
Sending CMD51
Sending CMD6
Sending CMD55
Sending CMD6
Buswidth = 4, clock: 400000
Sending CMD6
Buswidth = 4, clock: 20000000
Sending CMD16
Sending CMD17mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Sending CMD16
Sending CMD17dwmci_data_transfer: Timeout waiting for data!mmc_load_image_raw_sector: mmc block read error
Trying to boot from SPI
Trying to boot from MMC2
Sending CMD16
Sending CMD17mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Quoted 183 lines · Michal Suchánek
Hello,
after rebooting rk3399 Pinebook Pro mmc1 is no longer accessible from u-boot, and video is not working, only cold boot works.
This is not a problem anymore when Linux is loaded from another device.
Any idea how to debug this?
Thanks
Michal
U-Boot TPL 2022.07-rc5 (May 16 2022 - 12:00:00)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2022.07-rc5 (May 16 2022 - 12:00:00 +0000) Trying to boot from MMC1
NOTICE: BL31: v2.6(debug): NOTICE: BL31: Built : 14:50:40, Jul 1 2022 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 287 INFO: plat_rockchip_pmu_init(1624): pd status 3e INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9U-Boot 2022.07-rc5 (May 16 2022 - 00:00:00 +0000)
SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 Pinebook Pro DRAM: 3.9 GiB PMIC: RK808 Core: 317 devices, 34 uclasses, devicetree: separate MMC: mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: vidconsole Err: vidconsole Model: Pine64 Pinebook Pro Net: No ethernet found.starting USB...
Bus usb@fe380000:ehci_genericusb@fe380000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000:ehci_genericusb@fe3c0000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3e0000: USB OHCI 1.0
Bus usb@fe800000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe900000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3e0000 for devices... 4 USB Device(s) found scanning bus usb@fe800000 for devices... 1 USB Device(s) found scanning bus usb@fe900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
** Invalid partition 3 **
Couldn't find partition mmc 1:3
** Invalid partition 4 **
Couldn't find partition mmc 1:4
Scanning mmc 1:1...
BootOrder not defined
EFI boot manager: Cannot load any image
Found EFI removable media binary efi/boot/bootaa64.efi
857968 bytes read in 96 ms (8.5 MiB/s)
Booting /efi\boot\bootaa64.efiU-Boot TPL 2022.07-rc5 (May 16 2022 - 12:00:00)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stridelpddr4_set_rate: change freq to 400000000 mhz 0, 1lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2022.07-rc5 (May 16 2022 - 12:00:00 +0000) Trying to boot from MMC1
NOTICE: BL31: v2.6(debug): NOTICE: BL31: Built : 14:50:40, Jul 1 2022 INFO: GICv3 with legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 287 INFO: plat_rockchip_pmu_init(1624): pd status 3e INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9U-Boot 2022.07-rc5 (May 16 2022 - 00:00:00 +0000)
SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 Pinebook Pro DRAM: 3.9 GiB PMIC: RK808 Core: 317 devices, 34 uclasses, devicetree: separate MMC: mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: vidconsole Err: vidconsole Model: Pine64 Pinebook Pro Net: No ethernet found.starting USB...
Bus usb@fe380000:ehci_genericusb@fe380000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000:ehci_genericusb@fe3c0000: Failed to get clocks (ret=-19) Port not available.
Bus usb@fe3e0000: USB OHCI 1.0
Bus usb@fe800000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe900000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3e0000 for devices... 4 USB Device(s) found scanning bus usb@fe800000 for devices... 1 USB Device(s) found scanning bus usb@fe900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***
*** ERROR: Can't read GPT header ***find_valid_gpt: *** ERROR: Invalid Backup GPT ***
*** ERROR: Can't read GPT Entries ***find_valid_gpt: *** ERROR: Invalid GPT ***