PCI: qcom: Move IPQ8074 DBI register accesses after phy_power_on()
Subsystems (4)
PATCH v4 1/2 PCI: qcom: Move IPQ8074 DBI register accesses after phy_power_on()
Currently the Gen2 port in IPQ8074 will cause the system to hang as it accesses DBI registers in qcom_pcie_init_2_3_3(), and those are only accesible after phy_power_on().
Move the DBI read/writes to a new qcom_pcie_post_init_2_3_3(), which is executed after phy_power_on().
---
Changes in v4:
* Correct title and description
Changes in v3:
* Make sure it applies onto 5.19-rc3
* Update the commit description to make it clear this only affects the Gen2 port
Changes in v2:
* Rebase onto next-20220621
--- drivers/pci/controller/dwc/pcie-qcom.c | 48 +++++++++++++++----------- 1 file changed, 28 insertions(+), 20 deletions(-)
drivers/pci/controller/dwc/pcie-qcom.c +28 -20
@@ -1061,9 +1061,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u16 offset =dw_pcie_find_capability (pci,PCI_CAP_ID_EXP );int i, ret; -u32 val;for (i =0 ; i <ARRAY_SIZE (res->rst); i++) { ret =reset_control_assert (res->rst[i]);
@@ -1120,6 +1118,33 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) goto err_clk_aux; } +return 0 ; + +err_clk_aux: +clk_disable_unprepare (res->ahb_clk); +err_clk_ahb: +clk_disable_unprepare (res->axi_s_clk); +err_clk_axi_s: +clk_disable_unprepare (res->axi_m_clk); +err_clk_axi_m: +clk_disable_unprepare (res->iface); +err_clk_iface: +/* +* Not checking for failure, will anyway return +* the original failure in 'ret'. +*/ +for (i =0 ; i <ARRAY_SIZE (res->rst); i++) +reset_control_assert (res->rst[i]); + +return ret; +} + +static int qcom_pcie_post_init_2_3_3 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +u16 offset =dw_pcie_find_capability (pci,PCI_CAP_ID_EXP ); +u32 val; +writel (SLV_ADDR_SPACE_SZ , pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
@@ -1147,24 +1172,6 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) PCI_EXP_DEVCTL2);return 0 ; - -err_clk_aux: -clk_disable_unprepare (res->ahb_clk); -err_clk_ahb: -clk_disable_unprepare (res->axi_s_clk); -err_clk_axi_s: -clk_disable_unprepare (res->axi_m_clk); -err_clk_axi_m: -clk_disable_unprepare (res->iface); -err_clk_iface: -/* -* Not checking for failure, will anyway return -* the original failure in 'ret'. -*/ -for (i =0 ; i <ARRAY_SIZE (res->rst); i++) -reset_control_assert (res->rst[i]); - -return ret; }static int qcom_pcie_get_resources_2_7_0 (struct qcom_pcie *pcie)
@@ -1596,6 +1603,7 @@ static const struct qcom_pcie_ops ops_2_4_0 = {static const struct qcom_pcie_ops ops_2_3_3 = { .get_resources = qcom_pcie_get_resources_2_3_3, .init = qcom_pcie_init_2_3_3, + .post_init = qcom_pcie_post_init_2_3_3, .deinit = qcom_pcie_deinit_2_3_3, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, };
Signature · 1 line
2.36.1
PATCH v4 2/2 PCI: qcom: Move all DBI register accesses after phy_power_on()
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after phy_power_on().
---
Changes in v4:
* Move 2.7.0 accesses as well
* Correct title and description (Bjorn)
--- drivers/pci/controller/dwc/pcie-qcom.c | 215 ++++++++++++++----------- 1 file changed, 119 insertions(+), 96 deletions(-)
drivers/pci/controller/dwc/pcie-qcom.c +119 -96
@@ -348,8 +348,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -struct device_node *node = dev->of_node; -u32 val;int ret;/* reset the PCIe interface as uboot can leave it undefined state */
@@ -360,8 +358,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)reset_control_assert (res->ext_reset);reset_control_assert (res->phy_reset); -writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); - ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);if (ret <0 ) {dev_err (dev,"cannot enable regulators\n" );
@@ -408,6 +404,35 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->axi_reset); +err_deassert_axi: +reset_control_assert (res->por_reset); +err_deassert_por: +reset_control_assert (res->pci_reset); +err_deassert_pci: +reset_control_assert (res->phy_reset); +err_deassert_phy: +reset_control_assert (res->ext_reset); +err_deassert_ext: +reset_control_assert (res->ahb_reset); +err_deassert_ahb: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static int qcom_pcie_post_init_2_1_0 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +struct device *dev = pci->dev; +struct device_node *node = dev->of_node; +u32 val; + +writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );
@@ -451,23 +476,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);return 0 ; - -err_clks: -reset_control_assert (res->axi_reset); -err_deassert_axi: -reset_control_assert (res->por_reset); -err_deassert_por: -reset_control_assert (res->pci_reset); -err_deassert_pci: -reset_control_assert (res->phy_reset); -err_deassert_phy: -reset_control_assert (res->ext_reset); -err_deassert_ext: -reset_control_assert (res->ahb_reset); -err_deassert_ahb: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; }static int qcom_pcie_get_resources_1_0_0 (struct qcom_pcie *pcie)
@@ -555,16 +563,6 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) goto err_slave; } -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -if (IS_ENABLED (CONFIG_PCI_MSI )) { -u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - } -return 0 ; err_slave:clk_disable_unprepare (res->slave_bus);
@@ -580,6 +578,22 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)return ret; } +static int qcom_pcie_post_init_1_0_0 (struct qcom_pcie *pcie) +{ + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +if (IS_ENABLED (CONFIG_PCI_MSI )) { +u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + } + +return 0 ; +} +static void qcom_pcie_2_3_2_ltssm_enable (struct qcom_pcie *pcie) {u32 val;
@@ -648,7 +662,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);
@@ -681,27 +694,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) goto err_slave_clk; } -/* enable PCIe clocks and resets */ - val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); - val &= ~BIT (0 ); -writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); - -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -/* MAC PHY_POWERDOWN MUX DISABLE */ - val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); - val &= ~BIT (29 ); -writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - val |=BIT (4 ); -writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); -return 0 ; err_slave_clk:
@@ -722,8 +714,30 @@ static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; +u32 val;int ret; +/* enable PCIe clocks and resets */ + val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); + val &= ~BIT (0 ); +writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +/* MAC PHY_POWERDOWN MUX DISABLE */ + val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); + val &= ~BIT (29 ); +writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + val |=BIT (4 ); +writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + ret =clk_prepare_enable (res->pipe_clk);if (ret) {dev_err (dev,"cannot prepare/enable pipe clock\n" );
@@ -837,7 +851,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =reset_control_assert (res->axi_m_reset);
@@ -962,6 +975,33 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->ahb_reset); +err_rst_ahb: +reset_control_assert (res->pwr_reset); +err_rst_pwr: +reset_control_assert (res->axi_s_reset); +err_rst_axi_s: +reset_control_assert (res->axi_m_sticky_reset); +err_rst_axi_m_sticky: +reset_control_assert (res->axi_m_reset); +err_rst_axi_m: +reset_control_assert (res->pipe_sticky_reset); +err_rst_pipe_sticky: +reset_control_assert (res->pipe_reset); +err_rst_pipe: +reset_control_assert (res->phy_reset); +err_rst_phy: +reset_control_assert (res->phy_ahb_reset); +return ret; +} + +static int qcom_pcie_post_init_2_4_0 (struct qcom_pcie *pcie) +{ +u32 val; +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );
@@ -984,26 +1024,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 );return 0 ; - -err_clks: -reset_control_assert (res->ahb_reset); -err_rst_ahb: -reset_control_assert (res->pwr_reset); -err_rst_pwr: -reset_control_assert (res->axi_s_reset); -err_rst_axi_s: -reset_control_assert (res->axi_m_sticky_reset); -err_rst_axi_m_sticky: -reset_control_assert (res->axi_m_reset); -err_rst_axi_m: -reset_control_assert (res->pipe_sticky_reset); -err_rst_pipe_sticky: -reset_control_assert (res->pipe_reset); -err_rst_pipe: -reset_control_assert (res->phy_reset); -err_rst_phy: -reset_control_assert (res->phy_ahb_reset); -return ret; }static int qcom_pcie_get_resources_2_3_3 (struct qcom_pcie *pcie)
@@ -1237,7 +1257,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);
@@ -1271,6 +1290,28 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)/* Wait for reset to complete, required on SM8450 */ usleep_range (1000 ,1500 ); +return 0 ; +err_disable_clocks: +clk_bulk_disable_unprepare (res->num_clks, res->clks); +err_disable_regulators: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + +clk_bulk_disable_unprepare (res->num_clks, res->clks); +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); +} + +static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; +u32 val; +/* configure PCIe to RC mode */ writel (DEVICE_TYPE_RC , pcie->parf +PCIE20_PARF_DEVICE_TYPE );
@@ -1297,27 +1338,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); } -return 0 ; -err_disable_clocks: -clk_bulk_disable_unprepare (res->num_clks, res->clks); -err_disable_regulators: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; -} - -static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; - -clk_bulk_disable_unprepare (res->num_clks, res->clks); -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); -} - -static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; -/* Set pipe clock as clock source for pcie_pipe_clk_src */ if (pcie->cfg->pipe_clk_need_muxing)clk_set_parent (res->pipe_clk_src, res->phy_pipe_clk);
@@ -1569,6 +1589,7 @@ static const struct dw_pcie_host_ops qcom_pcie_dw_ops = {static const struct qcom_pcie_ops ops_2_1_0 = { .get_resources = qcom_pcie_get_resources_2_1_0, .init = qcom_pcie_init_2_1_0, + .post_init = qcom_pcie_post_init_2_1_0, .deinit = qcom_pcie_deinit_2_1_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };
@@ -1577,6 +1598,7 @@ static const struct qcom_pcie_ops ops_2_1_0 = {static const struct qcom_pcie_ops ops_1_0_0 = { .get_resources = qcom_pcie_get_resources_1_0_0, .init = qcom_pcie_init_1_0_0, + .post_init = qcom_pcie_post_init_1_0_0, .deinit = qcom_pcie_deinit_1_0_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };
@@ -1595,6 +1617,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {static const struct qcom_pcie_ops ops_2_4_0 = { .get_resources = qcom_pcie_get_resources_2_4_0, .init = qcom_pcie_init_2_4_0, + .post_init = qcom_pcie_post_init_2_4_0, .deinit = qcom_pcie_deinit_2_4_0, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, };
Signature · 1 line
2.36.1
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>
Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Quoted 358 lines
---
Changes in v4:
* Move 2.7.0 accesses as well
* Correct title and description (Bjorn)--- drivers/pci/controller/dwc/pcie-qcom.c | 215 ++++++++++++++----------- 1 file changed, 119 insertions(+), 96 deletions(-)drivers/pci/controller/dwc/pcie-qcom.c +119
-96@@ -348,8 +348,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -struct device_node *node = dev->of_node; -u32 val;int ret;/* reset the PCIe interface as uboot can leave it undefined state */ @@ -360,8 +358,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)reset_control_assert (res->ext_reset);reset_control_assert (res->phy_reset); -writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); - ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);if (ret <0 ) {dev_err (dev,"cannot enable regulators\n" );@@ -408,6 +404,35 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->axi_reset); +err_deassert_axi: +reset_control_assert (res->por_reset); +err_deassert_por: +reset_control_assert (res->pci_reset); +err_deassert_pci: +reset_control_assert (res->phy_reset); +err_deassert_phy: +reset_control_assert (res->ext_reset); +err_deassert_ext: +reset_control_assert (res->ahb_reset); +err_deassert_ahb: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static int qcom_pcie_post_init_2_1_0 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +struct device *dev = pci->dev; +struct device_node *node = dev->of_node; +u32 val; + +writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -451,23 +476,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);return 0 ; - -err_clks: -reset_control_assert (res->axi_reset); -err_deassert_axi: -reset_control_assert (res->por_reset); -err_deassert_por: -reset_control_assert (res->pci_reset); -err_deassert_pci: -reset_control_assert (res->phy_reset); -err_deassert_phy: -reset_control_assert (res->ext_reset); -err_deassert_ext: -reset_control_assert (res->ahb_reset); -err_deassert_ahb: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; }static int qcom_pcie_get_resources_1_0_0 (struct qcom_pcie *pcie)@@ -555,16 +563,6 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) goto err_slave; } -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -if (IS_ENABLED (CONFIG_PCI_MSI )) { -u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - } -return 0 ; err_slave:clk_disable_unprepare (res->slave_bus);@@ -580,6 +578,22 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)return ret; } +static int qcom_pcie_post_init_1_0_0 (struct qcom_pcie *pcie) +{ + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +if (IS_ENABLED (CONFIG_PCI_MSI )) { +u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + } + +return 0 ; +} +static void qcom_pcie_2_3_2_ltssm_enable (struct qcom_pcie *pcie) {u32 val;@@ -648,7 +662,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -681,27 +694,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) goto err_slave_clk; } -/* enable PCIe clocks and resets */ - val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); - val &= ~BIT (0 ); -writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); - -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -/* MAC PHY_POWERDOWN MUX DISABLE */ - val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); - val &= ~BIT (29 ); -writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - val |=BIT (4 ); -writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); -return 0 ; err_slave_clk:@@ -722,8 +714,30 @@ static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; +u32 val;int ret; +/* enable PCIe clocks and resets */ + val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); + val &= ~BIT (0 ); +writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +/* MAC PHY_POWERDOWN MUX DISABLE */ + val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); + val &= ~BIT (29 ); +writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + val |=BIT (4 ); +writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + ret =clk_prepare_enable (res->pipe_clk);if (ret) {dev_err (dev,"cannot prepare/enable pipe clock\n" );@@ -837,7 +851,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =reset_control_assert (res->axi_m_reset);@@ -962,6 +975,33 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->ahb_reset); +err_rst_ahb: +reset_control_assert (res->pwr_reset); +err_rst_pwr: +reset_control_assert (res->axi_s_reset); +err_rst_axi_s: +reset_control_assert (res->axi_m_sticky_reset); +err_rst_axi_m_sticky: +reset_control_assert (res->axi_m_reset); +err_rst_axi_m: +reset_control_assert (res->pipe_sticky_reset); +err_rst_pipe_sticky: +reset_control_assert (res->pipe_reset); +err_rst_pipe: +reset_control_assert (res->phy_reset); +err_rst_phy: +reset_control_assert (res->phy_ahb_reset); +return ret; +} + +static int qcom_pcie_post_init_2_4_0 (struct qcom_pcie *pcie) +{ +u32 val; +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -984,26 +1024,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 );return 0 ; - -err_clks: -reset_control_assert (res->ahb_reset); -err_rst_ahb: -reset_control_assert (res->pwr_reset); -err_rst_pwr: -reset_control_assert (res->axi_s_reset); -err_rst_axi_s: -reset_control_assert (res->axi_m_sticky_reset); -err_rst_axi_m_sticky: -reset_control_assert (res->axi_m_reset); -err_rst_axi_m: -reset_control_assert (res->pipe_sticky_reset); -err_rst_pipe_sticky: -reset_control_assert (res->pipe_reset); -err_rst_pipe: -reset_control_assert (res->phy_reset); -err_rst_phy: -reset_control_assert (res->phy_ahb_reset); -return ret; }static int qcom_pcie_get_resources_2_3_3 (struct qcom_pcie *pcie)@@ -1237,7 +1257,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -1271,6 +1290,28 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)/* Wait for reset to complete, required on SM8450 */ usleep_range (1000 ,1500 ); +return 0 ; +err_disable_clocks: +clk_bulk_disable_unprepare (res->num_clks, res->clks); +err_disable_regulators: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + +clk_bulk_disable_unprepare (res->num_clks, res->clks); +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); +} + +static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; +u32 val; +/* configure PCIe to RC mode */ writel (DEVICE_TYPE_RC , pcie->parf +PCIE20_PARF_DEVICE_TYPE );@@ -1297,27 +1338,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); } -return 0 ; -err_disable_clocks: -clk_bulk_disable_unprepare (res->num_clks, res->clks); -err_disable_regulators: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; -} - -static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; - -clk_bulk_disable_unprepare (res->num_clks, res->clks); -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); -} - -static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; -/* Set pipe clock as clock source for pcie_pipe_clk_src */ if (pcie->cfg->pipe_clk_need_muxing)clk_set_parent (res->pipe_clk_src, res->phy_pipe_clk);@@ -1569,6 +1589,7 @@ static const struct dw_pcie_host_ops qcom_pcie_dw_ops = {static const struct qcom_pcie_ops ops_2_1_0 = { .get_resources = qcom_pcie_get_resources_2_1_0, .init = qcom_pcie_init_2_1_0, + .post_init = qcom_pcie_post_init_2_1_0, .deinit = qcom_pcie_deinit_2_1_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1577,6 +1598,7 @@ static const struct qcom_pcie_ops ops_2_1_0 = {static const struct qcom_pcie_ops ops_1_0_0 = { .get_resources = qcom_pcie_get_resources_1_0_0, .init = qcom_pcie_init_1_0_0, + .post_init = qcom_pcie_post_init_1_0_0, .deinit = qcom_pcie_deinit_1_0_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1595,6 +1617,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {static const struct qcom_pcie_ops ops_2_4_0 = { .get_resources = qcom_pcie_get_resources_2_4_0, .init = qcom_pcie_init_2_4_0, + .post_init = qcom_pcie_post_init_2_4_0, .deinit = qcom_pcie_deinit_2_4_0, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, };Signature · 1 line
2.36.1
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
CC-ing Christian who did a lot of work on 2.1.0 (IPQ806x).
Regards,
Robert
Quoted 370 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Quoted 358 lines
---
Changes in v4:
* Move 2.7.0 accesses as well
* Correct title and description (Bjorn)--- drivers/pci/controller/dwc/pcie-qcom.c | 215 ++++++++++++++----------- 1 file changed, 119 insertions(+), 96 deletions(-)drivers/pci/controller/dwc/pcie-qcom.c +119
-97@@ -348,8 +348,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -struct device_node *node = dev->of_node; -u32 val;int ret;/* reset the PCIe interface as uboot can leave it undefined state */ @@ -360,8 +358,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)reset_control_assert (res->ext_reset);reset_control_assert (res->phy_reset); -writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); - ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);if (ret <0 ) {dev_err (dev,"cannot enable regulators\n" );@@ -408,6 +404,35 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->axi_reset); +err_deassert_axi: +reset_control_assert (res->por_reset); +err_deassert_por: +reset_control_assert (res->pci_reset); +err_deassert_pci: +reset_control_assert (res->phy_reset); +err_deassert_phy: +reset_control_assert (res->ext_reset); +err_deassert_ext: +reset_control_assert (res->ahb_reset); +err_deassert_ahb: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static int qcom_pcie_post_init_2_1_0 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +struct device *dev = pci->dev; +struct device_node *node = dev->of_node; +u32 val; + +writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -451,23 +476,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);return 0 ; - -err_clks: -reset_control_assert (res->axi_reset); -err_deassert_axi: -reset_control_assert (res->por_reset); -err_deassert_por: -reset_control_assert (res->pci_reset); -err_deassert_pci: -reset_control_assert (res->phy_reset); -err_deassert_phy: -reset_control_assert (res->ext_reset); -err_deassert_ext: -reset_control_assert (res->ahb_reset); -err_deassert_ahb: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; }static int qcom_pcie_get_resources_1_0_0 (struct qcom_pcie *pcie)@@ -555,16 +563,6 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) goto err_slave; } -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -if (IS_ENABLED (CONFIG_PCI_MSI )) { -u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - } -return 0 ; err_slave:clk_disable_unprepare (res->slave_bus);@@ -580,6 +578,22 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)return ret; } +static int qcom_pcie_post_init_1_0_0 (struct qcom_pcie *pcie) +{ + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +if (IS_ENABLED (CONFIG_PCI_MSI )) { +u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + } + +return 0 ; +} +static void qcom_pcie_2_3_2_ltssm_enable (struct qcom_pcie *pcie) {u32 val;@@ -648,7 +662,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -681,27 +694,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) goto err_slave_clk; } -/* enable PCIe clocks and resets */ - val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); - val &= ~BIT (0 ); -writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); - -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -/* MAC PHY_POWERDOWN MUX DISABLE */ - val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); - val &= ~BIT (29 ); -writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - val |=BIT (4 ); -writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); -return 0 ; err_slave_clk:@@ -722,8 +714,30 @@ static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; +u32 val;int ret; +/* enable PCIe clocks and resets */ + val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); + val &= ~BIT (0 ); +writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +/* MAC PHY_POWERDOWN MUX DISABLE */ + val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); + val &= ~BIT (29 ); +writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + val |=BIT (4 ); +writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + ret =clk_prepare_enable (res->pipe_clk);if (ret) {dev_err (dev,"cannot prepare/enable pipe clock\n" );@@ -837,7 +851,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =reset_control_assert (res->axi_m_reset);@@ -962,6 +975,33 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->ahb_reset); +err_rst_ahb: +reset_control_assert (res->pwr_reset); +err_rst_pwr: +reset_control_assert (res->axi_s_reset); +err_rst_axi_s: +reset_control_assert (res->axi_m_sticky_reset); +err_rst_axi_m_sticky: +reset_control_assert (res->axi_m_reset); +err_rst_axi_m: +reset_control_assert (res->pipe_sticky_reset); +err_rst_pipe_sticky: +reset_control_assert (res->pipe_reset); +err_rst_pipe: +reset_control_assert (res->phy_reset); +err_rst_phy: +reset_control_assert (res->phy_ahb_reset); +return ret; +} + +static int qcom_pcie_post_init_2_4_0 (struct qcom_pcie *pcie) +{ +u32 val; +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -984,26 +1024,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 );return 0 ; - -err_clks: -reset_control_assert (res->ahb_reset); -err_rst_ahb: -reset_control_assert (res->pwr_reset); -err_rst_pwr: -reset_control_assert (res->axi_s_reset); -err_rst_axi_s: -reset_control_assert (res->axi_m_sticky_reset); -err_rst_axi_m_sticky: -reset_control_assert (res->axi_m_reset); -err_rst_axi_m: -reset_control_assert (res->pipe_sticky_reset); -err_rst_pipe_sticky: -reset_control_assert (res->pipe_reset); -err_rst_pipe: -reset_control_assert (res->phy_reset); -err_rst_phy: -reset_control_assert (res->phy_ahb_reset); -return ret; }static int qcom_pcie_get_resources_2_3_3 (struct qcom_pcie *pcie)@@ -1237,7 +1257,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -1271,6 +1290,28 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)/* Wait for reset to complete, required on SM8450 */ usleep_range (1000 ,1500 ); +return 0 ; +err_disable_clocks: +clk_bulk_disable_unprepare (res->num_clks, res->clks); +err_disable_regulators: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + +clk_bulk_disable_unprepare (res->num_clks, res->clks); +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); +} + +static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; +u32 val; +/* configure PCIe to RC mode */ writel (DEVICE_TYPE_RC , pcie->parf +PCIE20_PARF_DEVICE_TYPE );@@ -1297,27 +1338,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); } -return 0 ; -err_disable_clocks: -clk_bulk_disable_unprepare (res->num_clks, res->clks); -err_disable_regulators: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; -} - -static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; - -clk_bulk_disable_unprepare (res->num_clks, res->clks); -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); -} - -static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; -/* Set pipe clock as clock source for pcie_pipe_clk_src */ if (pcie->cfg->pipe_clk_need_muxing)clk_set_parent (res->pipe_clk_src, res->phy_pipe_clk);@@ -1569,6 +1589,7 @@ static const struct dw_pcie_host_ops qcom_pcie_dw_ops = {static const struct qcom_pcie_ops ops_2_1_0 = { .get_resources = qcom_pcie_get_resources_2_1_0, .init = qcom_pcie_init_2_1_0, + .post_init = qcom_pcie_post_init_2_1_0, .deinit = qcom_pcie_deinit_2_1_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1577,6 +1598,7 @@ static const struct qcom_pcie_ops ops_2_1_0 = {static const struct qcom_pcie_ops ops_1_0_0 = { .get_resources = qcom_pcie_get_resources_1_0_0, .init = qcom_pcie_init_1_0_0, + .post_init = qcom_pcie_post_init_1_0_0, .deinit = qcom_pcie_deinit_1_0_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1595,6 +1617,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {static const struct qcom_pcie_ops ops_2_4_0 = { .get_resources = qcom_pcie_get_resources_2_4_0, .init = qcom_pcie_init_2_4_0, + .post_init = qcom_pcie_post_init_2_4_0, .deinit = qcom_pcie_deinit_2_4_0, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, }; --2.36.1
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 18 lines · Robert Marko
CC-ing Christian who did a lot of work on 2.1.0 (IPQ806x).
Regards,
RobertQuoted 12 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].
As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came up
The cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.
This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to havewritel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
in qcom_pcie_init_2_1_0 right after the reset_contro_assert.
This command is also present in qcom_pcie_init_2_3_2 where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved to post_init.
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30d
Quoted 358 lines
Quoted 358 lines
Quoted 358 lines
---
Changes in v4:
* Move 2.7.0 accesses as well
* Correct title and description (Bjorn)--- drivers/pci/controller/dwc/pcie-qcom.c | 215 ++++++++++++++----------- 1 file changed, 119 insertions(+), 96 deletions(-)drivers/pci/controller/dwc/pcie-qcom.c +119
-97@@ -348,8 +348,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -struct device_node *node = dev->of_node; -u32 val;int ret;/* reset the PCIe interface as uboot can leave it undefined state */ @@ -360,8 +358,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)reset_control_assert (res->ext_reset);reset_control_assert (res->phy_reset); -writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); - ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);if (ret <0 ) {dev_err (dev,"cannot enable regulators\n" );@@ -408,6 +404,35 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->axi_reset); +err_deassert_axi: +reset_control_assert (res->por_reset); +err_deassert_por: +reset_control_assert (res->pci_reset); +err_deassert_pci: +reset_control_assert (res->phy_reset); +err_deassert_phy: +reset_control_assert (res->ext_reset); +err_deassert_ext: +reset_control_assert (res->ahb_reset); +err_deassert_ahb: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static int qcom_pcie_post_init_2_1_0 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +struct device *dev = pci->dev; +struct device_node *node = dev->of_node; +u32 val; + +writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -451,23 +476,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);return 0 ; - -err_clks: -reset_control_assert (res->axi_reset); -err_deassert_axi: -reset_control_assert (res->por_reset); -err_deassert_por: -reset_control_assert (res->pci_reset); -err_deassert_pci: -reset_control_assert (res->phy_reset); -err_deassert_phy: -reset_control_assert (res->ext_reset); -err_deassert_ext: -reset_control_assert (res->ahb_reset); -err_deassert_ahb: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; }static int qcom_pcie_get_resources_1_0_0 (struct qcom_pcie *pcie)@@ -555,16 +563,6 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) goto err_slave; } -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -if (IS_ENABLED (CONFIG_PCI_MSI )) { -u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - } -return 0 ; err_slave:clk_disable_unprepare (res->slave_bus);@@ -580,6 +578,22 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)return ret; } +static int qcom_pcie_post_init_1_0_0 (struct qcom_pcie *pcie) +{ + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +if (IS_ENABLED (CONFIG_PCI_MSI )) { +u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + } + +return 0 ; +} +static void qcom_pcie_2_3_2_ltssm_enable (struct qcom_pcie *pcie) {u32 val;@@ -648,7 +662,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -681,27 +694,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) goto err_slave_clk; } -/* enable PCIe clocks and resets */ - val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); - val &= ~BIT (0 ); -writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); - -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -/* MAC PHY_POWERDOWN MUX DISABLE */ - val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); - val &= ~BIT (29 ); -writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - val |=BIT (4 ); -writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); -return 0 ; err_slave_clk:@@ -722,8 +714,30 @@ static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; +u32 val;int ret; +/* enable PCIe clocks and resets */ + val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); + val &= ~BIT (0 ); +writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +/* MAC PHY_POWERDOWN MUX DISABLE */ + val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); + val &= ~BIT (29 ); +writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + val |=BIT (4 ); +writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + ret =clk_prepare_enable (res->pipe_clk);if (ret) {dev_err (dev,"cannot prepare/enable pipe clock\n" );@@ -837,7 +851,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =reset_control_assert (res->axi_m_reset);@@ -962,6 +975,33 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->ahb_reset); +err_rst_ahb: +reset_control_assert (res->pwr_reset); +err_rst_pwr: +reset_control_assert (res->axi_s_reset); +err_rst_axi_s: +reset_control_assert (res->axi_m_sticky_reset); +err_rst_axi_m_sticky: +reset_control_assert (res->axi_m_reset); +err_rst_axi_m: +reset_control_assert (res->pipe_sticky_reset); +err_rst_pipe_sticky: +reset_control_assert (res->pipe_reset); +err_rst_pipe: +reset_control_assert (res->phy_reset); +err_rst_phy: +reset_control_assert (res->phy_ahb_reset); +return ret; +} + +static int qcom_pcie_post_init_2_4_0 (struct qcom_pcie *pcie) +{ +u32 val; +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -984,26 +1024,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 );return 0 ; - -err_clks: -reset_control_assert (res->ahb_reset); -err_rst_ahb: -reset_control_assert (res->pwr_reset); -err_rst_pwr: -reset_control_assert (res->axi_s_reset); -err_rst_axi_s: -reset_control_assert (res->axi_m_sticky_reset); -err_rst_axi_m_sticky: -reset_control_assert (res->axi_m_reset); -err_rst_axi_m: -reset_control_assert (res->pipe_sticky_reset); -err_rst_pipe_sticky: -reset_control_assert (res->pipe_reset); -err_rst_pipe: -reset_control_assert (res->phy_reset); -err_rst_phy: -reset_control_assert (res->phy_ahb_reset); -return ret; }static int qcom_pcie_get_resources_2_3_3 (struct qcom_pcie *pcie)@@ -1237,7 +1257,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -1271,6 +1290,28 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)/* Wait for reset to complete, required on SM8450 */ usleep_range (1000 ,1500 ); +return 0 ; +err_disable_clocks: +clk_bulk_disable_unprepare (res->num_clks, res->clks); +err_disable_regulators: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + +clk_bulk_disable_unprepare (res->num_clks, res->clks); +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); +} + +static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; +u32 val; +/* configure PCIe to RC mode */ writel (DEVICE_TYPE_RC , pcie->parf +PCIE20_PARF_DEVICE_TYPE );@@ -1297,27 +1338,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); } -return 0 ; -err_disable_clocks: -clk_bulk_disable_unprepare (res->num_clks, res->clks); -err_disable_regulators: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; -} - -static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; - -clk_bulk_disable_unprepare (res->num_clks, res->clks); -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); -} - -static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; -/* Set pipe clock as clock source for pcie_pipe_clk_src */ if (pcie->cfg->pipe_clk_need_muxing)clk_set_parent (res->pipe_clk_src, res->phy_pipe_clk);@@ -1569,6 +1589,7 @@ static const struct dw_pcie_host_ops qcom_pcie_dw_ops = {static const struct qcom_pcie_ops ops_2_1_0 = { .get_resources = qcom_pcie_get_resources_2_1_0, .init = qcom_pcie_init_2_1_0, + .post_init = qcom_pcie_post_init_2_1_0, .deinit = qcom_pcie_deinit_2_1_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1577,6 +1598,7 @@ static const struct qcom_pcie_ops ops_2_1_0 = {static const struct qcom_pcie_ops ops_1_0_0 = { .get_resources = qcom_pcie_get_resources_1_0_0, .init = qcom_pcie_init_1_0_0, + .post_init = qcom_pcie_post_init_1_0_0, .deinit = qcom_pcie_deinit_1_0_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1595,6 +1617,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {static const struct qcom_pcie_ops ops_2_4_0 = { .get_resources = qcom_pcie_get_resources_2_4_0, .init = qcom_pcie_init_2_4_0, + .post_init = qcom_pcie_post_init_2_4_0, .deinit = qcom_pcie_deinit_2_4_0, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, }; --2.36.1
Signature · 1 line
Ansuel
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 47 lines · Christian Marangi
Quoted 18 lines · Robert Marko
CC-ing Christian who did a lot of work on 2.1.0 (IPQ806x).
Regards,
RobertQuoted 12 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came upThe cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to have
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
inqcom_pcie_init_2_1_0right after thereset_contro_assert.This command is also present in
qcom_pcie_init_2_3_2where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved topost_init.
Quoted 6 lines
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30d
While testing this I notice something odd...
2_4_2 prepare the pipe clock only AFTER PCIe clocks and reset are enabled while in 2_1_0... That made me think there could be a problem with the current code of 2_1_0... A quick change made me discover that the problem is actually that we enable prepare_enable clock BEFORE the value is written in PCIE20_PARF_PHY_CTRL.
By moving the clk_bulk_prepare_enable after the "enable PCIe clocks and resets" make the pci work with the current change...
So it could be that the current changes are correct and it's really just a bug in 2_1_0 enabling clock before writing the correct value...
Tell me how to proceed... think at this point a good idea would be to create a separate patch and fix this for good.
Also bonus question, should I drop the bulk_prepare_enable and follow the pattern of 2_3_2 and enable aux, cfg, master and slave in init and pipe in post init or I can keep it? (still have to test but I assume that it will work.)
Quoted 361 lines
Quoted 358 lines
Quoted 358 lines
Quoted 358 lines
---
Changes in v4:
* Move 2.7.0 accesses as well
* Correct title and description (Bjorn)--- drivers/pci/controller/dwc/pcie-qcom.c | 215 ++++++++++++++----------- 1 file changed, 119 insertions(+), 96 deletions(-)drivers/pci/controller/dwc/pcie-qcom.c +119
-97@@ -348,8 +348,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -struct device_node *node = dev->of_node; -u32 val;int ret;/* reset the PCIe interface as uboot can leave it undefined state */ @@ -360,8 +358,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)reset_control_assert (res->ext_reset);reset_control_assert (res->phy_reset); -writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); - ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);if (ret <0 ) {dev_err (dev,"cannot enable regulators\n" );@@ -408,6 +404,35 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->axi_reset); +err_deassert_axi: +reset_control_assert (res->por_reset); +err_deassert_por: +reset_control_assert (res->pci_reset); +err_deassert_pci: +reset_control_assert (res->phy_reset); +err_deassert_phy: +reset_control_assert (res->ext_reset); +err_deassert_ext: +reset_control_assert (res->ahb_reset); +err_deassert_ahb: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static int qcom_pcie_post_init_2_1_0 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +struct device *dev = pci->dev; +struct device_node *node = dev->of_node; +u32 val; + +writel (1 , pcie->parf +PCIE20_PARF_PHY_CTRL ); +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -451,23 +476,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);return 0 ; - -err_clks: -reset_control_assert (res->axi_reset); -err_deassert_axi: -reset_control_assert (res->por_reset); -err_deassert_por: -reset_control_assert (res->pci_reset); -err_deassert_pci: -reset_control_assert (res->phy_reset); -err_deassert_phy: -reset_control_assert (res->ext_reset); -err_deassert_ext: -reset_control_assert (res->ahb_reset); -err_deassert_ahb: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; }static int qcom_pcie_get_resources_1_0_0 (struct qcom_pcie *pcie)@@ -555,16 +563,6 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) goto err_slave; } -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -if (IS_ENABLED (CONFIG_PCI_MSI )) { -u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); - } -return 0 ; err_slave:clk_disable_unprepare (res->slave_bus);@@ -580,6 +578,22 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)return ret; } +static int qcom_pcie_post_init_1_0_0 (struct qcom_pcie *pcie) +{ + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +if (IS_ENABLED (CONFIG_PCI_MSI )) { +u32 val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); + } + +return 0 ; +} +static void qcom_pcie_2_3_2_ltssm_enable (struct qcom_pcie *pcie) {u32 val;@@ -648,7 +662,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -681,27 +694,6 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) goto err_slave_clk; } -/* enable PCIe clocks and resets */ - val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); - val &= ~BIT (0 ); -writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); - -/* change DBI base address */ -writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); - -/* MAC PHY_POWERDOWN MUX DISABLE */ - val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); - val &= ~BIT (29 ); -writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - val |=BIT (4 ); -writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); - - val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); - val |=BIT (31 ); -writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); -return 0 ; err_slave_clk:@@ -722,8 +714,30 @@ static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; +u32 val;int ret; +/* enable PCIe clocks and resets */ + val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); + val &= ~BIT (0 ); +writel (val, pcie->parf +PCIE20_PARF_PHY_CTRL ); + +/* change DBI base address */ +writel (0 , pcie->parf +PCIE20_PARF_DBI_BASE_ADDR ); + +/* MAC PHY_POWERDOWN MUX DISABLE */ + val =readl (pcie->parf +PCIE20_PARF_SYS_CTRL ); + val &= ~BIT (29 ); +writel (val, pcie->parf +PCIE20_PARF_SYS_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + val |=BIT (4 ); +writel (val, pcie->parf +PCIE20_PARF_MHI_CLOCK_RESET_CTRL ); + + val =readl (pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + val |=BIT (31 ); +writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 ); + ret =clk_prepare_enable (res->pipe_clk);if (ret) {dev_err (dev,"cannot prepare/enable pipe clock\n" );@@ -837,7 +851,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =reset_control_assert (res->axi_m_reset);@@ -962,6 +975,33 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)if (ret) goto err_clks; +return 0 ; + +err_clks: +reset_control_assert (res->ahb_reset); +err_rst_ahb: +reset_control_assert (res->pwr_reset); +err_rst_pwr: +reset_control_assert (res->axi_s_reset); +err_rst_axi_s: +reset_control_assert (res->axi_m_sticky_reset); +err_rst_axi_m_sticky: +reset_control_assert (res->axi_m_reset); +err_rst_axi_m: +reset_control_assert (res->pipe_sticky_reset); +err_rst_pipe_sticky: +reset_control_assert (res->pipe_reset); +err_rst_pipe: +reset_control_assert (res->phy_reset); +err_rst_phy: +reset_control_assert (res->phy_ahb_reset); +return ret; +} + +static int qcom_pcie_post_init_2_4_0 (struct qcom_pcie *pcie) +{ +u32 val; +/* enable PCIe clocks and resets */ val =readl (pcie->parf +PCIE20_PARF_PHY_CTRL ); val &= ~BIT (0 );@@ -984,26 +1024,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 );return 0 ; - -err_clks: -reset_control_assert (res->ahb_reset); -err_rst_ahb: -reset_control_assert (res->pwr_reset); -err_rst_pwr: -reset_control_assert (res->axi_s_reset); -err_rst_axi_s: -reset_control_assert (res->axi_m_sticky_reset); -err_rst_axi_m_sticky: -reset_control_assert (res->axi_m_reset); -err_rst_axi_m: -reset_control_assert (res->pipe_sticky_reset); -err_rst_pipe_sticky: -reset_control_assert (res->pipe_reset); -err_rst_pipe: -reset_control_assert (res->phy_reset); -err_rst_phy: -reset_control_assert (res->phy_ahb_reset); -return ret; }static int qcom_pcie_get_resources_2_3_3 (struct qcom_pcie *pcie)@@ -1237,7 +1257,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u32 val;int ret; ret =regulator_bulk_enable (ARRAY_SIZE (res->supplies), res->supplies);@@ -1271,6 +1290,28 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)/* Wait for reset to complete, required on SM8450 */ usleep_range (1000 ,1500 ); +return 0 ; +err_disable_clocks: +clk_bulk_disable_unprepare (res->num_clks, res->clks); +err_disable_regulators: +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); + +return ret; +} + +static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + +clk_bulk_disable_unprepare (res->num_clks, res->clks); +regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); +} + +static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) +{ +struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; +u32 val; +/* configure PCIe to RC mode */ writel (DEVICE_TYPE_RC , pcie->parf +PCIE20_PARF_DEVICE_TYPE );@@ -1297,27 +1338,6 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)writel (val, pcie->parf +PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT ); } -return 0 ; -err_disable_clocks: -clk_bulk_disable_unprepare (res->num_clks, res->clks); -err_disable_regulators: -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); - -return ret; -} - -static void qcom_pcie_deinit_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; - -clk_bulk_disable_unprepare (res->num_clks, res->clks); -regulator_bulk_disable (ARRAY_SIZE (res->supplies), res->supplies); -} - -static int qcom_pcie_post_init_2_7_0 (struct qcom_pcie *pcie) -{ -struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; -/* Set pipe clock as clock source for pcie_pipe_clk_src */ if (pcie->cfg->pipe_clk_need_muxing)clk_set_parent (res->pipe_clk_src, res->phy_pipe_clk);@@ -1569,6 +1589,7 @@ static const struct dw_pcie_host_ops qcom_pcie_dw_ops = {static const struct qcom_pcie_ops ops_2_1_0 = { .get_resources = qcom_pcie_get_resources_2_1_0, .init = qcom_pcie_init_2_1_0, + .post_init = qcom_pcie_post_init_2_1_0, .deinit = qcom_pcie_deinit_2_1_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1577,6 +1598,7 @@ static const struct qcom_pcie_ops ops_2_1_0 = {static const struct qcom_pcie_ops ops_1_0_0 = { .get_resources = qcom_pcie_get_resources_1_0_0, .init = qcom_pcie_init_1_0_0, + .post_init = qcom_pcie_post_init_1_0_0, .deinit = qcom_pcie_deinit_1_0_0, .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, };@@ -1595,6 +1617,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {static const struct qcom_pcie_ops ops_2_4_0 = { .get_resources = qcom_pcie_get_resources_2_4_0, .init = qcom_pcie_init_2_4_0, + .post_init = qcom_pcie_post_init_2_4_0, .deinit = qcom_pcie_deinit_2_4_0, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, }; --2.36.1
Signature · 1 line
Ansuel
Signature · 1 line
Ansuel
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 55 lines · Christian Marangi
Quoted 40 lines · Christian Marangi
Quoted 11 lines · Robert Marko
Quoted 10 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came upThe cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to have
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
inqcom_pcie_init_2_1_0right after thereset_contro_assert.This command is also present in
qcom_pcie_init_2_3_2where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved topost_init.Quoted 5 lines
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30dWhile testing this I notice something odd...
2_4_2 prepare the pipe clock only AFTER PCIe clocks and reset are enabled while in 2_1_0... That made me think there could be a problem with the current code of 2_1_0... A quick change made me discover that the problem is actually that we enable
prepare_enableclock BEFORE the value is written inPCIE20_PARF_PHY_CTRL.
Quoted 8 lines
By moving the
clk_bulk_prepare_enableafter the "enable PCIe clocks and resets" make the pci work with the current change...So it could be that the current changes are correct and it's really just a bug in 2_1_0 enabling clock before writing the correct value...
Tell me how to proceed... think at this point a good idea would be to create a separate patch and fix this for good.
Hmm, I think I made a mistake when I put this patch in the middle and applied other stuff on top of it. I'd like to just postpone this patch while we work out these issues, but I think it's not completely trivial since it's in the middle. I'll try to straighten this out next week.
Quoted 4 lines
Also bonus question, should I drop the
bulk_prepare_enableand follow the pattern of 2_3_2 and enable aux, cfg, master and slave in init and pipe in post init or I can keep it? (still have to test but I assume that it will work.)
I haven't looked at the code again, but will just offer the opinion that unnecessary differences in structure often hide bugs, and they're always minor speed bumps for readers.
Bjorn
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 62 lines · Bjorn Helgaas
Quoted 61 lines · Christian Marangi
Quoted 40 lines · Christian Marangi
Quoted 11 lines · Robert Marko
Quoted 10 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came upThe cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to have
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
inqcom_pcie_init_2_1_0right after thereset_contro_assert.This command is also present in
qcom_pcie_init_2_3_2where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved topost_init.Quoted 5 lines
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30dWhile testing this I notice something odd...
2_4_2 prepare the pipe clock only AFTER PCIe clocks and reset are enabled while in 2_1_0... That made me think there could be a problem with the current code of 2_1_0... A quick change made me discover that the problem is actually that we enable
prepare_enableclock BEFORE the value is written inPCIE20_PARF_PHY_CTRL.By moving the
clk_bulk_prepare_enableafter the "enable PCIe clocks and resets" make the pci work with the current change...So it could be that the current changes are correct and it's really just a bug in 2_1_0 enabling clock before writing the correct value...
Quoted 9 lines
Quoted 2 lines
Tell me how to proceed... think at this point a good idea would be to create a separate patch and fix this for good.
Hmm, I think I made a mistake when I put this patch in the middle and applied other stuff on top of it. I'd like to just postpone this patch while we work out these issues, but I think it's not completely trivial since it's in the middle. I'll try to straighten this out next week.
From my discoveries it really seems just a bug in 2_1_0 with enabling the phy clk BEFORE setting the require bit...
Moving the bulk_prepare_enable after the bit is set makes everything works as it should... If you want I can send a patch as that is clearly a bug and currenty we have a workaround in place...
(with the patch the workaround can be dropped aka we even remove a line of code)
Quoted 10 lines
Quoted 4 lines
Also bonus question, should I drop the
bulk_prepare_enableand follow the pattern of 2_3_2 and enable aux, cfg, master and slave in init and pipe in post init or I can keep it? (still have to test but I assume that it will work.)I haven't looked at the code again, but will just offer the opinion that unnecessary differences in structure often hide bugs, and they're always minor speed bumps for readers.
Bjorn
Considering it won't change anything and pci 2_1_0 use the bulk api... calling each clock separately will actually makes things less readable... Sooo think it's just a line to drop and a code move.
Signature · 1 line
Ansuel
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 72 lines · Christian Marangi
Quoted 62 lines · Bjorn Helgaas
Quoted 61 lines · Christian Marangi
Quoted 40 lines · Christian Marangi
Quoted 11 lines · Robert Marko
Quoted 10 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came upThe cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to have
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
inqcom_pcie_init_2_1_0right after thereset_contro_assert.This command is also present in
qcom_pcie_init_2_3_2where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved topost_init.Quoted 5 lines
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30dWhile testing this I notice something odd...
2_4_2 prepare the pipe clock only AFTER PCIe clocks and reset are enabled while in 2_1_0... That made me think there could be a problem with the current code of 2_1_0... A quick change made me discover that the problem is actually that we enable
prepare_enableclock BEFORE the value is written inPCIE20_PARF_PHY_CTRL.By moving the
clk_bulk_prepare_enableafter the "enable PCIe clocks and resets" make the pci work with the current change...So it could be that the current changes are correct and it's really just a bug in 2_1_0 enabling clock before writing the correct value...
Quoted 8 lines
Quoted 2 lines
Tell me how to proceed... think at this point a good idea would be to create a separate patch and fix this for good.
Hmm, I think I made a mistake when I put this patch in the middle and applied other stuff on top of it. I'd like to just postpone this patch while we work out these issues, but I think it's not completely trivial since it's in the middle. I'll try to straighten this out next week.
Quoted 6 lines
From my discoveries it really seems just a bug in 2_1_0 with enabling the phy clk BEFORE setting the require bit...
Moving the
bulk_prepare_enableafter the bit is set makes everything works as it should... If you want I can send a patch as that is clearly a bug and currenty we have a workaround in place...
That'd be great! Since it's an actual bug fix, I think it would be good if it were a separate patch instead of doing in the middle of a patch that also does other things.
Bjorn
Re: [PATCH v4 2/2] PCI: qcom: Move all DBI register accesses after phy_power_on()
Quoted 80 lines · Bjorn Helgaas
Quoted 72 lines · Christian Marangi
Quoted 62 lines · Bjorn Helgaas
Quoted 61 lines · Christian Marangi
Quoted 40 lines · Christian Marangi
Quoted 11 lines · Robert Marko
Quoted 10 lines · Bjorn Helgaas
Quoted 6 lines · Robert Marko
IPQ8074 requires the PHY to be powered on before accessing DBI registers. It's not clear whether other variants have the same dependency, but there seems to be no reason for them to be different, so move all the DBI accesses from .init() to .post_init() so they are all after
phy_power_on().Signed-off-by Robert Marko <[email protected]>Would any of the qcom driver folks care to review and ack this? Stanimir, Andy, Bjorn A (from get_maintainer.pl)?
Hi Bjorn,
I tested this on ipq806x and the current patch cause regression as pci doesn't work anymore...
This is a before the patch [1] and this is an after [2].As you notice the main problem here is
[ 2.559962] qcom-pcie 1b700000.pci: Phy link never came upThe cause of this has already been bisected and actually it was a fixup pushed some time ago for 2_1_0.
Uboot can leave the pci in an underfined state and this
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL); is never called.This is mandatory to a correct init and MUST be called before regulator enable and reset deassert or the "Phy link never came up" problem is triggered.
So to fix this we just have to have
writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
inqcom_pcie_init_2_1_0right after thereset_contro_assert.This command is also present in
qcom_pcie_init_2_3_2where the same exact reg is written so I assume 2_3_2 have the same regression and the write must be placed in init and can't be moved topost_init.Quoted 5 lines
Feel free to tell me how to proceed if I should post an additional patch or you prefer Robi to respin this with the few lines reverted.
[1] https://gist.github.com/Ansuel/ec827319e585630356fc586273db6f0d
[2] https://gist.github.com/Ansuel/63fbcab2681cd28a61ec52d7874fa30dWhile testing this I notice something odd...
2_4_2 prepare the pipe clock only AFTER PCIe clocks and reset are enabled while in 2_1_0... That made me think there could be a problem with the current code of 2_1_0... A quick change made me discover that the problem is actually that we enable
prepare_enableclock BEFORE the value is written inPCIE20_PARF_PHY_CTRL.By moving the
clk_bulk_prepare_enableafter the "enable PCIe clocks and resets" make the pci work with the current change...So it could be that the current changes are correct and it's really just a bug in 2_1_0 enabling clock before writing the correct value...
Quoted 8 lines
Quoted 2 lines
Tell me how to proceed... think at this point a good idea would be to create a separate patch and fix this for good.
Hmm, I think I made a mistake when I put this patch in the middle and applied other stuff on top of it. I'd like to just postpone this patch while we work out these issues, but I think it's not completely trivial since it's in the middle. I'll try to straighten this out next week.
Quoted 6 lines
From my discoveries it really seems just a bug in 2_1_0 with enabling the phy clk BEFORE setting the require bit...
Moving the
bulk_prepare_enableafter the bit is set makes everything works as it should... If you want I can send a patch as that is clearly a bug and currenty we have a workaround in place...
Quoted 5 lines
That'd be great! Since it's an actual bug fix, I think it would be good if it were a separate patch instead of doing in the middle of a patch that also does other things.
Bjorn
Just sent the small fix that will indirectly make this series work as it should.
Signature · 1 line
Ansuel
Quoted 11 lines · Robert Marko
Currently the Gen2 port in IPQ8074 will cause the system to hang as it accesses DBI registers in
qcom_pcie_init_2_3_3(), and those are only accesible afterphy_power_on().Move the DBI read/writes to a new
qcom_pcie_post_init_2_3_3(), which is executed afterphy_power_on().Fixes a0fd361db8e5 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")Signed-off-by Robert Marko <[email protected]>Reviewed-by Dmitry Baryshkov <[email protected]>
Hi,
Bjorn, is there something else I need to fixup?
Regards,
Robert
Quoted 99 lines
---
Changes in v4:
* Correct title and descriptionChanges in v3:
* Make sure it applies onto 5.19-rc3
* Update the commit description to make it clear this only affects the Gen2 portChanges in v2:
* Rebase onto next-20220621--- drivers/pci/controller/dwc/pcie-qcom.c | 48 +++++++++++++++----------- 1 file changed, 28 insertions(+), 20 deletions(-)drivers/pci/controller/dwc/pcie-qcom.c +28
-21@@ -1061,9 +1061,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;struct dw_pcie *pci = pcie->pci;struct device *dev = pci->dev; -u16 offset =dw_pcie_find_capability (pci,PCI_CAP_ID_EXP );int i, ret; -u32 val;for (i =0 ; i <ARRAY_SIZE (res->rst); i++) { ret =reset_control_assert (res->rst[i]);@@ -1120,6 +1118,33 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) goto err_clk_aux; } +return 0 ; + +err_clk_aux: +clk_disable_unprepare (res->ahb_clk); +err_clk_ahb: +clk_disable_unprepare (res->axi_s_clk); +err_clk_axi_s: +clk_disable_unprepare (res->axi_m_clk); +err_clk_axi_m: +clk_disable_unprepare (res->iface); +err_clk_iface: +/* +* Not checking for failure, will anyway return +* the original failure in 'ret'. +*/ +for (i =0 ; i <ARRAY_SIZE (res->rst); i++) +reset_control_assert (res->rst[i]); + +return ret; +} + +static int qcom_pcie_post_init_2_3_3 (struct qcom_pcie *pcie) +{ +struct dw_pcie *pci = pcie->pci; +u16 offset =dw_pcie_find_capability (pci,PCI_CAP_ID_EXP ); +u32 val; +writel (SLV_ADDR_SPACE_SZ , pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);@@ -1147,24 +1172,6 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) PCI_EXP_DEVCTL2);return 0 ; - -err_clk_aux: -clk_disable_unprepare (res->ahb_clk); -err_clk_ahb: -clk_disable_unprepare (res->axi_s_clk); -err_clk_axi_s: -clk_disable_unprepare (res->axi_m_clk); -err_clk_axi_m: -clk_disable_unprepare (res->iface); -err_clk_iface: -/* -* Not checking for failure, will anyway return -* the original failure in 'ret'. -*/ -for (i =0 ; i <ARRAY_SIZE (res->rst); i++) -reset_control_assert (res->rst[i]); - -return ret; }static int qcom_pcie_get_resources_2_7_0 (struct qcom_pcie *pcie)@@ -1596,6 +1603,7 @@ static const struct qcom_pcie_ops ops_2_4_0 = {static const struct qcom_pcie_ops ops_2_3_3 = { .get_resources = qcom_pcie_get_resources_2_3_3, .init = qcom_pcie_init_2_3_3, + .post_init = qcom_pcie_post_init_2_3_3, .deinit = qcom_pcie_deinit_2_3_3, .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, }; --2.36.1