Skip to contentSkip to conversation

serial: fsl_lpuart: zero out parity bit in CS7 mode

PATCH New [email protected] 1 participant 1 message Jul 8, 2022 TTY layer and serial drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 serial: fsl_lpuart: zero out parity bit in CS7 mode

The LPUART hardware doesn't zero out the parity bit on the received characters. This behavior won't impact the use cases of CS8 because the parity bit is the 9th bit which is not currently used by software. But the parity bit for CS7 must be zeroed out by software in order to get the correct raw data.

---
 drivers/tty/serial/fsl_lpuart.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)
drivers/tty/serial/fsl_lpuart.c +25 -3
index 8fe0494d4057b..202431f75e913 100644
@@ -274,6 +274,8 @@ struct lpuart_port {
 	int			rx_dma_rng_buf_len;
 	unsigned int		dma_tx_nents;
 	wait_queue_head_t	dma_wait;
+    bool		is_cs7; /* Set to true when character size is 7 */
+						/* and the parity is enabled			*/
 };
 
 struct lpuart_soc_data {
@@ -1022,6 +1024,9 @@ static void lpuart32_rxint(struct lpuart_port *sport)
 				flg = TTY_OVERRUN;
 		}
 
+        if (sport->is_cs7)
+			rx &= 0x7F;
+
 		if (tty_insert_flip_char(port, rx, flg) == 0)
 			sport->port.icount.buf_overrun++;
 	}
@@ -1107,6 +1112,17 @@ static void lpuart_handle_sysrq(struct lpuart_port *sport)
 	}
 }
 
+static inline int lpuart_tty_insert_flip_string(struct tty_port *port,
+               unsigned char *chars, size_t size, bool is_cs7)
+{
+	int i;
+
+	if (is_cs7)
+		for (i = 0; i < size; i++)
+			chars[i] &= 0x7F;
+	return tty_insert_flip_string(port, chars, size);
+}
+
 static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
 {
 	struct tty_port *port = &sport->port.state->port;
@@ -1217,7 +1233,8 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
 	if (ring->head < ring->tail) {
 		count = sport->rx_sgl.length - ring->tail;
 
-		copied = tty_insert_flip_string(port, ring->buf + ring->tail, count);
+		copied = lpuart_tty_insert_flip_string(port, ring->buf + ring->tail,
+					count, sport->is_cs7);
 		if (copied != count)
 			sport->port.icount.buf_overrun++;
 		ring->tail = 0;
@@ -1227,8 +1244,9 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
 	/* Finally we read data from tail to head */
 	if (ring->tail < ring->head) {
 		count = ring->head - ring->tail;
-		copied = tty_insert_flip_string(port, ring->buf + ring->tail, count);
-		if (copied != count)
+		copied = lpuart_tty_insert_flip_string(port, ring->buf + ring->tail,
+					count, sport->is_cs7);
+	if (copied != count)
 			sport->port.icount.buf_overrun++;
 		/* Wrap ring->head if needed */
 		if (ring->head >= sport->rx_sgl.length)
@@ -2066,6 +2084,7 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 	ctrl = old_ctrl = lpuart32_read(&sport->port, UARTCTRL);
 	bd = lpuart32_read(&sport->port, UARTBAUD);
 	modem = lpuart32_read(&sport->port, UARTMODIR);
+	sport->is_cs7 = false;
 	/*
 	 * only support CS8 and CS7, and for CS7 must enable PE.
 	 * supported mode:
@@ -2184,6 +2203,9 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 	lpuart32_write(&sport->port, ctrl, UARTCTRL);
 	/* restore control register */
 
+	if ((ctrl & (UARTCTRL_PE | UARTCTRL_M)) == UARTCTRL_PE)
+		sport->is_cs7 = true;
+
 	if (old && sport->lpuart_dma_rx_use) {
 		if (!lpuart_start_rx_dma(sport))
 			rx_dma_timer_init(sport);
Signature · 1 line
2.25.1