extcon: usbc-tusb320: Factor out extcon into dedicated functions
Subsystems (2)
PATCH 1/2 extcon: usbc-tusb320: Factor out extcon into dedicated functions
Move extcon code into separate functions in preparation for addition of USB TYPE-C support. No functional change.
---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]
--- drivers/extcon/extcon-usbc-tusb320.c | 75 +++++++++++++++++----------- 1 file changed, 46 insertions(+), 29 deletions(-)
drivers/extcon/extcon-usbc-tusb320.c +46 -29
@@ -184,19 +184,9 @@ static struct tusb320_ops tusb320l_ops = { .get_revision = tusb320l_get_revision, }; -static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +static void tusb320_extcon_irq_handler (struct tusb320_priv *priv,u8 reg) { -struct tusb320_priv *priv = dev_id;int state, polarity; -unsigned reg; - -if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { -dev_err (priv->dev,"error during i2c read!\n" ); -return IRQ_NONE ; - } - -if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) -return IRQ_NONE ; state = (reg >>TUSB320_REG9_ATTACHED_STATE_SHIFT ) &TUSB320_REG9_ATTACHED_STATE_MASK ;
@@ -219,6 +209,22 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)extcon_sync (priv->edev,EXTCON_USB_HOST ); priv->state = state; +} + +static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +{ +struct tusb320_priv *priv = dev_id; +unsigned int reg; + +if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { +dev_err (priv->dev,"error during i2c read!\n" ); +return IRQ_NONE ; + } + +if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) +return IRQ_NONE ; + +tusb320_extcon_irq_handler (priv, reg);regmap_write (priv->regmap,TUSB320_REG9 , reg);
@@ -230,8 +236,32 @@ static const struct regmap_config tusb320_regmap_config = { .val_bits = 8, }; -static int tusb320_extcon_probe (struct i2c_client *client, -const struct i2c_device_id *id) +static int tusb320_extcon_probe (struct tusb320_priv *priv) +{ +int ret; + + priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); +if (IS_ERR (priv->edev)) { +dev_err (priv->dev,"failed to allocate extcon device\n" ); +return PTR_ERR (priv->edev); + } + + ret =devm_extcon_dev_register (priv->dev, priv->edev); +if (ret <0 ) { +dev_err (priv->dev,"failed to register extcon device\n" ); +return ret; + } + +extcon_set_property_capability (priv->edev,EXTCON_USB , +EXTCON_PROP_USB_TYPEC_POLARITY ); +extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , +EXTCON_PROP_USB_TYPEC_POLARITY ); + +return 0 ; +} + +static int tusb320_probe (struct i2c_client *client, +const struct i2c_device_id *id) {struct tusb320_priv *priv;const void *match_data;
@@ -257,12 +287,6 @@ static int tusb320_extcon_probe(struct i2c_client *client, priv->ops = (struct tusb320_ops *)match_data; - priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); -if (IS_ERR (priv->edev)) { -dev_err (priv->dev,"failed to allocate extcon device\n" ); -return PTR_ERR (priv->edev); - } -if (priv->ops->get_revision) { ret = priv->ops->get_revision (priv, &revision);if (ret)
@@ -272,16 +296,9 @@ static int tusb320_extcon_probe(struct i2c_client *client,dev_info (priv->dev,"chip revision %d\n" , revision); } - ret =devm_extcon_dev_register (priv->dev, priv->edev); -if (ret <0 ) { -dev_err (priv->dev,"failed to register extcon device\n" ); + ret =tusb320_extcon_probe (priv); +if (ret)return ret; - } - -extcon_set_property_capability (priv->edev,EXTCON_USB , -EXTCON_PROP_USB_TYPEC_POLARITY ); -extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , -EXTCON_PROP_USB_TYPEC_POLARITY );/* update initial state */ tusb320_irq_handler (client->irq, priv);
@@ -313,7 +330,7 @@ static const struct of_device_id tusb320_extcon_dt_match[] = {MODULE_DEVICE_TABLE (of, tusb320_extcon_dt_match);static struct i2c_driver tusb320_extcon_driver = { - .probe = tusb320_extcon_probe, + .probe = tusb320_probe, .driver = { .name ="extcon-tusb320" , .of_match_table = tusb320_extcon_dt_match,
Signature · 1 line
2.35.1
PATCH 2/2 extcon: usbc-tusb320: Add USB TYPE-C support
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]
--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)
drivers/extcon/Kconfig +1 -1
@@ -180,7 +180,7 @@ config EXTCON_USBC_CROS_EC config EXTCON_USBC_TUSB320 tristate "TI TUSB320 USB-C extcon support" - depends on I2C + depends on I2C && TYPEC select REGMAP_I2C help Say Y here to enable support for USB Type C cable detection extcon
drivers/extcon/extcon-usbc-tusb320.c +159 -0
207 lines not on this page · raw message
Signature · 1 line
2.35.1
kernel test robot
build botRe: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
I love your patch! Perhaps something to improve:
Hi Marek,
I love your patch! Perhaps something to improve:
[auto build test WARNING on chanwoo-extcon/extcon-next] [also build test WARNING on linus/master v5.19-rc8 next-20220728] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Marek-Vasut/extcon-usbc-tusb320-Factor-out-extcon-into-dedicated-functions/20220731-020545 base: https://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon.git extcon-next config: x86_64-randconfig-a012 (https://download.01.org/0day-ci/archive/20220731/[email protected]/config) compiler: clang version 16.0.0 (https://github.com/llvm/llvm-project 52cd00cabf479aa7eb6dbb063b7ba41ea57bce9e)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/7bce9c0377f5e41fa29f57af40f436a48e2260b1
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Marek-Vasut/extcon-usbc-tusb320-Factor-out-extcon-into-dedicated-functions/20220731-020545 git checkout 7bce9c0377f5e41fa29f57af40f436a48e2260b1
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash drivers/extcon/
If you fix the issue, kindly add following tag where applicable
All warnings (new ones prefixed by >>):
>> drivers/extcon/extcon-usbc-tusb320.c:19: warning: expecting prototype for drivers/extcon/extcon-tusb320.c(). Prototype was for TUSB320_REG8() instead
vim +19 drivers/extcon/extcon-usbc-tusb320.c
18
> 19 #define TUSB320_REG8 0x8
20 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE GENMASK(7, 6)
21 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB 0x0
22 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A 0x1
23 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A 0x2
24 #define TUSB320_REG8_CURRENT_MODE_DETECT GENMASK(5, 4)
25 #define TUSB320_REG8_CURRENT_MODE_DETECT_DEF 0x0
26 #define TUSB320_REG8_CURRENT_MODE_DETECT_MED 0x1
27 #define TUSB320_REG8_CURRENT_MODE_DETECT_ACC 0x2
28 #define TUSB320_REG8_CURRENT_MODE_DETECT_HI 0x3
29 #define TUSB320_REG8_ACCESSORY_CONNECTED GENMASK(3, 2)
30 #define TUSB320_REG8_ACCESSORY_CONNECTED_NONE 0x0
31 #define TUSB320_REG8_ACCESSORY_CONNECTED_AUDIO 0x4
32 #define TUSB320_REG8_ACCESSORY_CONNECTED_ACC 0x5
33 #define TUSB320_REG8_ACCESSORY_CONNECTED_DEBUG 0x6
34 #define TUSB320_REG8_ACTIVE_CABLE_DETECTION BIT(0)
35 Signature · 2 lines
0-DAY CI Kernel Test Service https://01.org/lkp
kernel test robot
build botRe: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
In reply to Marek VasutI love your patch! Perhaps something to improve:
Hi Marek,
I love your patch! Perhaps something to improve:
[auto build test WARNING on chanwoo-extcon/extcon-next] [also build test WARNING on linus/master v5.19-rc8 next-20220728] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Marek-Vasut/extcon-usbc-tusb320-Factor-out-extcon-into-dedicated-functions/20220731-020545 base: https://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon.git extcon-next config: sparc-randconfig-r031-20220731 (https://download.01.org/0day-ci/archive/20220731/[email protected]/config) compiler: sparc64-linux-gcc (GCC) 12.1.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/7bce9c0377f5e41fa29f57af40f436a48e2260b1
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Marek-Vasut/extcon-usbc-tusb320-Factor-out-extcon-into-dedicated-functions/20220731-020545 git checkout 7bce9c0377f5e41fa29f57af40f436a48e2260b1
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=sparc SHELL=/bin/bash drivers/extcon/
If you fix the issue, kindly add following tag where applicable
All warnings (new ones prefixed by >>):
>> drivers/extcon/extcon-usbc-tusb320.c:19: warning: expecting prototype for drivers/extcon/extcon-tusb320.c(). Prototype was for TUSB320_REG8() instead
vim +19 drivers/extcon/extcon-usbc-tusb320.c
18
> 19 #define TUSB320_REG8 0x8
20 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE GENMASK(7, 6)
21 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB 0x0
22 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A 0x1
23 #define TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A 0x2
24 #define TUSB320_REG8_CURRENT_MODE_DETECT GENMASK(5, 4)
25 #define TUSB320_REG8_CURRENT_MODE_DETECT_DEF 0x0
26 #define TUSB320_REG8_CURRENT_MODE_DETECT_MED 0x1
27 #define TUSB320_REG8_CURRENT_MODE_DETECT_ACC 0x2
28 #define TUSB320_REG8_CURRENT_MODE_DETECT_HI 0x3
29 #define TUSB320_REG8_ACCESSORY_CONNECTED GENMASK(3, 2)
30 #define TUSB320_REG8_ACCESSORY_CONNECTED_NONE 0x0
31 #define TUSB320_REG8_ACCESSORY_CONNECTED_AUDIO 0x4
32 #define TUSB320_REG8_ACCESSORY_CONNECTED_ACC 0x5
33 #define TUSB320_REG8_ACCESSORY_CONNECTED_DEBUG 0x6
34 #define TUSB320_REG8_ACTIVE_CABLE_DETECTION BIT(0)
35 Signature · 2 lines
0-DAY CI Kernel Test Service https://01.org/lkp
Re: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
In reply to Marek VasutQuoted 10 lines · Marek Vasut
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>
Quoted 245 lines
---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)drivers/extcon/Kconfig +1
-1@@ -180,7 +180,7 @@ config EXTCON_USBC_CROS_EC config EXTCON_USBC_TUSB320 tristate "TI TUSB320 USB-C extcon support" - depends on I2C + depends on I2C && TYPEC select REGMAP_I2C help Say Y here to enable support for USB Type C cable detection extcondrivers/extcon/extcon-usbc-tusb320.c +159
-0@@ -6,6 +6,7 @@* Author: Michael Auchter <[email protected]> */ +#include <linux/bitfield.h> #include <linux/extcon-provider.h> #include <linux/i2c.h> #include <linux/init.h> @@ -13,6 +14,24 @@#include <linux/kernel.h> #include <linux/module.h> #include <linux/regmap.h> +#include <linux/usb/typec.h> + +#define TUSB320_REG8 0x8 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE GENMASK(7, 6) +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB 0x0 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A 0x1 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A 0x2 +#define TUSB320_REG8_CURRENT_MODE_DETECT GENMASK(5, 4) +#define TUSB320_REG8_CURRENT_MODE_DETECT_DEF 0x0 +#define TUSB320_REG8_CURRENT_MODE_DETECT_MED 0x1 +#define TUSB320_REG8_CURRENT_MODE_DETECT_ACC 0x2 +#define TUSB320_REG8_CURRENT_MODE_DETECT_HI 0x3 +#define TUSB320_REG8_ACCESSORY_CONNECTED GENMASK(3, 2) +#define TUSB320_REG8_ACCESSORY_CONNECTED_NONE 0x0 +#define TUSB320_REG8_ACCESSORY_CONNECTED_AUDIO 0x4 +#define TUSB320_REG8_ACCESSORY_CONNECTED_ACC 0x5 +#define TUSB320_REG8_ACCESSORY_CONNECTED_DEBUG 0x6 +#define TUSB320_REG8_ACTIVE_CABLE_DETECTION BIT(0)#define TUSB320_REG9 0x9#define TUSB320_REG9_ATTACHED_STATE_SHIFT 6@@ -55,6 +74,10 @@ struct tusb320_priv {struct extcon_dev *edev;struct tusb320_ops *ops;enum tusb320_attached_state state; +struct typec_port *port; +struct typec_capability cap; +enum typec_port_type port_type; +enum typec_pwr_opmode pwr_opmode; };static const char *const tusb_attached_states[] = {@@ -184,6 +207,44 @@ static struct tusb320_ops tusb320l_ops = { .get_revision = tusb320l_get_revision, }; +static int tusb320_set_adv_pwr_mode (struct tusb320_priv *priv) +{ +u8 mode; + +if (priv->pwr_opmode ==TYPEC_PWR_MODE_USB ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB ; +else if (priv->pwr_opmode ==TYPEC_PWR_MODE_1_5A ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A ; +else if (priv->pwr_opmode ==TYPEC_PWR_MODE_3_0A ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A ; +else /* No other mode is supported. */ +return -EINVAL ; + +return regmap_write_bits (priv->regmap,TUSB320_REG8 , +TUSB320_REG8_CURRENT_MODE_ADVERTISE , +FIELD_PREP (TUSB320_REG8_CURRENT_MODE_ADVERTISE , + mode)); +} + +static int tusb320_port_type_set (struct typec_port *port, +enum typec_port_type type) +{ +struct tusb320_priv *priv =typec_get_drvdata (port); + +if (type ==TYPEC_PORT_SRC ) +return priv->ops->set_mode (priv,TUSB320_MODE_DFP ); +else if (type ==TYPEC_PORT_SNK ) +return priv->ops->set_mode (priv,TUSB320_MODE_UFP ); +else if (type ==TYPEC_PORT_DRP ) +return priv->ops->set_mode (priv,TUSB320_MODE_DRP ); +else +return priv->ops->set_mode (priv,TUSB320_MODE_PORT ); +} + +static const struct typec_operations tusb320_typec_ops = { + .port_type_set = tusb320_port_type_set, +}; +static void tusb320_extcon_irq_handler (struct tusb320_priv *priv,u8 reg) {int state, polarity;@@ -211,6 +272,47 @@ static void tusb320_extcon_irq_handler(struct tusb320_priv *priv, u8 reg) priv->state = state; } +static void tusb320_typec_irq_handler (struct tusb320_priv *priv,u8 reg9) +{ +struct typec_port *port = priv->port; +struct device *dev = priv->dev; +u8 mode, role, state; +int ret, reg8; +bool ori; + + ori = reg9 &TUSB320_REG9_CABLE_DIRECTION ; +typec_set_orientation (port, ori ?TYPEC_ORIENTATION_REVERSE : +TYPEC_ORIENTATION_NORMAL ); + + state = (reg9 >>TUSB320_REG9_ATTACHED_STATE_SHIFT ) & +TUSB320_REG9_ATTACHED_STATE_MASK ; +if (state ==TUSB320_ATTACHED_STATE_DFP ) + role =TYPEC_SOURCE ; +else + role =TYPEC_SINK ; + +typec_set_vconn_role (port, role); +typec_set_pwr_role (port, role); +typec_set_data_role (port, role ==TYPEC_SOURCE ? +TYPEC_HOST :TYPEC_DEVICE ); + + ret =regmap_read (priv->regmap,TUSB320_REG8 , ®8); +if (ret) { +dev_err (dev,"error during reg8 i2c read, ret=%d!\n" , ret); +return ; + } + + mode =FIELD_GET (TUSB320_REG8_CURRENT_MODE_DETECT , reg8); +if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_DEF ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_USB ); +else if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_MED ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_1_5A ); +else if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_HI ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_3_0A ); +else /* Charge through accessory */ +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_USB ); +} +static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) {struct tusb320_priv *priv = dev_id;@@ -225,6 +327,7 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)return IRQ_NONE ;tusb320_extcon_irq_handler (priv, reg); +tusb320_typec_irq_handler (priv, reg);regmap_write (priv->regmap,TUSB320_REG9 , reg);@@ -260,6 +363,58 @@ static int tusb320_extcon_probe(struct tusb320_priv *priv)return 0 ; } +static int tusb320_typec_probe (struct i2c_client *client, +struct tusb320_priv *priv) +{ +struct fwnode_handle *connector; +const char *cap_str; +int ret; + +/* The Type-C connector is optional, for backward compatibility. */ + connector =device_get_named_child_node (&client->dev,"connector" ); +if (!connector) +return 0 ; + +/* Type-C connector found. */ + ret =typec_get_fw_cap (&priv->cap, connector); +if (ret) +return ret; + + priv->port_type = priv->cap.type; + +/* This goes into register 0x8 field CURRENT_MODE_ADVERTISE */ + ret =fwnode_property_read_string (connector,"typec-power-opmode" , &cap_str); +if (ret) +return ret; + + ret =typec_find_pwr_opmode (cap_str); +if (ret <0 ) +return ret; +if (ret ==TYPEC_PWR_MODE_PD ) +return -EINVAL ; + + priv->pwr_opmode = ret; + +/* Initialize the hardware with the devicetree settings. */ + ret =tusb320_set_adv_pwr_mode (priv); +if (ret) +return ret; + + priv->cap.revision =USB_TYPEC_REV_1_1 ; + priv->cap.accessory[0 ] =TYPEC_ACCESSORY_AUDIO ; + priv->cap.accessory[1 ] =TYPEC_ACCESSORY_DEBUG ; + priv->cap.orientation_aware = true; + priv->cap.driver_data = priv; + priv->cap.ops = &tusb320_typec_ops; + priv->cap.fwnode = connector; + + priv->port =typec_register_port (&client->dev, &priv->cap); +if (IS_ERR (priv->port)) +return PTR_ERR (priv->port); + +return 0 ; +} +static int tusb320_probe (struct i2c_client *client,const struct i2c_device_id *id) {@@ -300,6 +455,10 @@ static int tusb320_probe(struct i2c_client *client,if (ret)return ret; + ret =tusb320_typec_probe (client, priv); +if (ret) +return ret; +/* update initial state */ tusb320_irq_handler (client->irq, priv);Signature · 1 line
2.35.1
Signature · 1 line
heikki
Re: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
Quoted 7 lines · Heikki Krogerus
Quoted 6 lines · Marek Vasut
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Quoted 6 lines
Quoted 4 lines
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>Acked-by Heikki Krogerus <[email protected]>
I wonder, can this now be applied ?
The LKP robot is picking up on macro name, i.e. the report seems bogus ?
Re: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
In reply to Marek VasutHi Marek,
Quoted 16 lines · Marek Vasut
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]
Quoted 4 lines
--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)
Happy to see I'm not the only one that observed this. I wonder if you saw also my previous stab at this:
https://lore.kernel.org/linux-usb/[email protected]/
I had some issues with the dt-bindings which I could not reconcile, but the basic problem was how to describe a typec accessory mode mux connected to the TUSB320. Perhaps you have a better intuition for how this should look?
One thing that is missing from your implementation that we are using on our end is the USB role switch. I set this from the typec driver via usb_role_switch_set_role().
Kind regards,
Alvin
Re: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
Quoted 1 line · Alvin Šipraga
Hi Marek,
Hi,
Quoted 22 lines · Marek Vasut
Quoted 16 lines
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]Quoted 4 lines
--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)
Quoted 4 lines
Happy to see I'm not the only one that observed this. I wonder if you saw also my previous stab at this:
I have not.
Quoted 8 lines
I had some issues with the dt-bindings which I could not reconcile, but the basic problem was how to describe a typec accessory mode mux connected to the TUSB320. Perhaps you have a better intuition for how this should look?
One thing that is missing from your implementation that we are using on our end is the USB role switch. I set this from the typec driver via
usb_role_switch_set_role().
I only use this chip to detect charger type (and cable polarity), the device where this is integrated is always peripheral and cannot charge other devices or become host.
But I think those aforementioned requirements could be extended on top of this patch, can they not ? I recall I looked at least at the direction detection and that could be added easily. I have no way of testing any of that functionality, so I didn't add them as part of the patch.
Alvin Šipraga
Reviewed-byRe: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
Quoted 43 lines · Marek Vasut
Quoted 1 line · Alvin Šipraga
Hi Marek,
Hi,
Quoted 22 lines · Marek Vasut
Quoted 16 lines
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]Quoted 4 lines
--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)Quoted 4 lines
Happy to see I'm not the only one that observed this. I wonder if you saw also my previous stab at this:
I have not.
Quoted 8 lines
I had some issues with the dt-bindings which I could not reconcile, but the basic problem was how to describe a typec accessory mode mux connected to the TUSB320. Perhaps you have a better intuition for how this should look?
One thing that is missing from your implementation that we are using on our end is the USB role switch. I set this from the typec driver via
usb_role_switch_set_role().
Quoted 8 lines
I only use this chip to detect charger type (and cable polarity), the device where this is integrated is always peripheral and cannot charge other devices or become host.
But I think those aforementioned requirements could be extended on top of this patch, can they not ? I recall I looked at least at the direction detection and that could be added easily. I have no way of testing any of that functionality, so I didn't add them as part of the patch.
Sure - if your patch gets merged then I'll just extend it. Fair enough that you cannot test on your board.
To that end, you can add:
Thanks!
Kind regards,
Alvin
Re: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
Quoted 53 lines · Alvin Šipraga
Quoted 43 lines · Marek Vasut
Quoted 1 line · Alvin Šipraga
Hi Marek,
Hi,
Quoted 22 lines · Marek Vasut
Quoted 16 lines
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]Quoted 4 lines
--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)Quoted 4 lines
Happy to see I'm not the only one that observed this. I wonder if you saw also my previous stab at this:
I have not.
Quoted 8 lines
I had some issues with the dt-bindings which I could not reconcile, but the basic problem was how to describe a typec accessory mode mux connected to the TUSB320. Perhaps you have a better intuition for how this should look?
One thing that is missing from your implementation that we are using on our end is the USB role switch. I set this from the typec driver via
usb_role_switch_set_role().Quoted 8 lines
I only use this chip to detect charger type (and cable polarity), the device where this is integrated is always peripheral and cannot charge other devices or become host.
But I think those aforementioned requirements could be extended on top of this patch, can they not ? I recall I looked at least at the direction detection and that could be added easily. I have no way of testing any of that functionality, so I didn't add them as part of the patch.
Quoted 6 lines
Sure - if your patch gets merged then I'll just extend it. Fair enough that you cannot test on your board.
To that end, you can add:
Reviewed-by Alvin Šipraga <[email protected]>
Thanks.
If you plan to submit anything on top, I might be able to test at least the charger detect and plug orientation still works ... but that's probably something you can also test on your own, that's the easy part of the USB-C.
Chanwoo Choi
AppliedRe: [PATCH 2/2] extcon: usbc-tusb320: Add USB TYPE-C support
In reply to Marek VasutQuoted 243 lines · Marek Vasut
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem, which can expose details collected by the TUSB320 in a far more precise way than extcon. Since there are existing users in the kernel and in DT which depend on the extcon interface, keep it for now.
Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]--- drivers/extcon/Kconfig | 2 +- drivers/extcon/extcon-usbc-tusb320.c | 159 +++++++++++++++++++++++++++ 2 files changed, 160 insertions(+), 1 deletion(-)drivers/extcon/Kconfig +1
-1@@ -180,7 +180,7 @@ config EXTCON_USBC_CROS_EC config EXTCON_USBC_TUSB320 tristate "TI TUSB320 USB-C extcon support" - depends on I2C + depends on I2C && TYPEC select REGMAP_I2C help Say Y here to enable support for USB Type C cable detection extcondrivers/extcon/extcon-usbc-tusb320.c +155
-0@@ -6,6 +6,7 @@* Author: Michael Auchter <[email protected]> */ +#include <linux/bitfield.h> #include <linux/extcon-provider.h> #include <linux/i2c.h> #include <linux/init.h> @@ -13,6 +14,24 @@#include <linux/kernel.h> #include <linux/module.h> #include <linux/regmap.h> +#include <linux/usb/typec.h> + +#define TUSB320_REG8 0x8 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE GENMASK(7, 6) +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB 0x0 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A 0x1 +#define TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A 0x2 +#define TUSB320_REG8_CURRENT_MODE_DETECT GENMASK(5, 4) +#define TUSB320_REG8_CURRENT_MODE_DETECT_DEF 0x0 +#define TUSB320_REG8_CURRENT_MODE_DETECT_MED 0x1 +#define TUSB320_REG8_CURRENT_MODE_DETECT_ACC 0x2 +#define TUSB320_REG8_CURRENT_MODE_DETECT_HI 0x3 +#define TUSB320_REG8_ACCESSORY_CONNECTED GENMASK(3, 2) +#define TUSB320_REG8_ACCESSORY_CONNECTED_NONE 0x0 +#define TUSB320_REG8_ACCESSORY_CONNECTED_AUDIO 0x4 +#define TUSB320_REG8_ACCESSORY_CONNECTED_ACC 0x5 +#define TUSB320_REG8_ACCESSORY_CONNECTED_DEBUG 0x6 +#define TUSB320_REG8_ACTIVE_CABLE_DETECTION BIT(0)#define TUSB320_REG9 0x9#define TUSB320_REG9_ATTACHED_STATE_SHIFT 6@@ -55,6 +74,10 @@ struct tusb320_priv {struct extcon_dev *edev;struct tusb320_ops *ops;enum tusb320_attached_state state; +struct typec_port *port; +struct typec_capability cap; +enum typec_port_type port_type; +enum typec_pwr_opmode pwr_opmode; };static const char *const tusb_attached_states[] = {@@ -184,6 +207,44 @@ static struct tusb320_ops tusb320l_ops = { .get_revision = tusb320l_get_revision, }; +static int tusb320_set_adv_pwr_mode (struct tusb320_priv *priv) +{ +u8 mode; + +if (priv->pwr_opmode ==TYPEC_PWR_MODE_USB ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_USB ; +else if (priv->pwr_opmode ==TYPEC_PWR_MODE_1_5A ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_15A ; +else if (priv->pwr_opmode ==TYPEC_PWR_MODE_3_0A ) + mode =TUSB320_REG8_CURRENT_MODE_ADVERTISE_30A ; +else /* No other mode is supported. */ +return -EINVAL ; + +return regmap_write_bits (priv->regmap,TUSB320_REG8 , +TUSB320_REG8_CURRENT_MODE_ADVERTISE , +FIELD_PREP (TUSB320_REG8_CURRENT_MODE_ADVERTISE , + mode)); +} + +static int tusb320_port_type_set (struct typec_port *port, +enum typec_port_type type) +{ +struct tusb320_priv *priv =typec_get_drvdata (port); + +if (type ==TYPEC_PORT_SRC ) +return priv->ops->set_mode (priv,TUSB320_MODE_DFP ); +else if (type ==TYPEC_PORT_SNK ) +return priv->ops->set_mode (priv,TUSB320_MODE_UFP ); +else if (type ==TYPEC_PORT_DRP ) +return priv->ops->set_mode (priv,TUSB320_MODE_DRP ); +else +return priv->ops->set_mode (priv,TUSB320_MODE_PORT ); +} + +static const struct typec_operations tusb320_typec_ops = { + .port_type_set = tusb320_port_type_set, +}; +static void tusb320_extcon_irq_handler (struct tusb320_priv *priv,u8 reg) {int state, polarity;@@ -211,6 +272,47 @@ static void tusb320_extcon_irq_handler(struct tusb320_priv *priv, u8 reg) priv->state = state; } +static void tusb320_typec_irq_handler (struct tusb320_priv *priv,u8 reg9) +{ +struct typec_port *port = priv->port; +struct device *dev = priv->dev; +u8 mode, role, state; +int ret, reg8; +bool ori; + + ori = reg9 &TUSB320_REG9_CABLE_DIRECTION ; +typec_set_orientation (port, ori ?TYPEC_ORIENTATION_REVERSE : +TYPEC_ORIENTATION_NORMAL ); + + state = (reg9 >>TUSB320_REG9_ATTACHED_STATE_SHIFT ) & +TUSB320_REG9_ATTACHED_STATE_MASK ; +if (state ==TUSB320_ATTACHED_STATE_DFP ) + role =TYPEC_SOURCE ; +else + role =TYPEC_SINK ; + +typec_set_vconn_role (port, role); +typec_set_pwr_role (port, role); +typec_set_data_role (port, role ==TYPEC_SOURCE ? +TYPEC_HOST :TYPEC_DEVICE ); + + ret =regmap_read (priv->regmap,TUSB320_REG8 , ®8); +if (ret) { +dev_err (dev,"error during reg8 i2c read, ret=%d!\n" , ret); +return ; + } + + mode =FIELD_GET (TUSB320_REG8_CURRENT_MODE_DETECT , reg8); +if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_DEF ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_USB ); +else if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_MED ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_1_5A ); +else if (mode ==TUSB320_REG8_CURRENT_MODE_DETECT_HI ) +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_3_0A ); +else /* Charge through accessory */ +typec_set_pwr_opmode (port,TYPEC_PWR_MODE_USB ); +} +static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) {struct tusb320_priv *priv = dev_id;@@ -225,6 +327,7 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)return IRQ_NONE ;tusb320_extcon_irq_handler (priv, reg); +tusb320_typec_irq_handler (priv, reg);regmap_write (priv->regmap,TUSB320_REG9 , reg);@@ -260,6 +363,58 @@ static int tusb320_extcon_probe(struct tusb320_priv *priv)return 0 ; } +static int tusb320_typec_probe (struct i2c_client *client, +struct tusb320_priv *priv) +{ +struct fwnode_handle *connector; +const char *cap_str; +int ret; + +/* The Type-C connector is optional, for backward compatibility. */ + connector =device_get_named_child_node (&client->dev,"connector" ); +if (!connector) +return 0 ; + +/* Type-C connector found. */ + ret =typec_get_fw_cap (&priv->cap, connector); +if (ret) +return ret; + + priv->port_type = priv->cap.type; + +/* This goes into register 0x8 field CURRENT_MODE_ADVERTISE */ + ret =fwnode_property_read_string (connector,"typec-power-opmode" , &cap_str); +if (ret) +return ret; + + ret =typec_find_pwr_opmode (cap_str); +if (ret <0 ) +return ret; +if (ret ==TYPEC_PWR_MODE_PD ) +return -EINVAL ; + + priv->pwr_opmode = ret; + +/* Initialize the hardware with the devicetree settings. */ + ret =tusb320_set_adv_pwr_mode (priv); +if (ret) +return ret; + + priv->cap.revision =USB_TYPEC_REV_1_1 ; + priv->cap.accessory[0 ] =TYPEC_ACCESSORY_AUDIO ; + priv->cap.accessory[1 ] =TYPEC_ACCESSORY_DEBUG ; + priv->cap.orientation_aware = true; + priv->cap.driver_data = priv; + priv->cap.ops = &tusb320_typec_ops; + priv->cap.fwnode = connector; + + priv->port =typec_register_port (&client->dev, &priv->cap); +if (IS_ERR (priv->port)) +return PTR_ERR (priv->port); + +return 0 ; +} +static int tusb320_probe (struct i2c_client *client,const struct i2c_device_id *id) {
drivers/extcon/extcon-usbc-tusb320.c static int tusb320_probe(struct i2c_client *client, · line 464
Quoted 10 lines
drivers/extcon/extcon-usbc-tusb320.c +4
-0@@ -300,6 +455,10 @@ static int tusb320_probe(struct i2c_client *client,if (ret)return ret; + ret =tusb320_typec_probe (client, priv); +if (ret) +return ret; +/* update initial state */ tusb320_irq_handler (client->irq, priv);
Applied it. Thanks.
Signature · 3 lines
Best Regards, Samsung Electronics Chanwoo Choi
Quoted 4 lines · Marek Vasut
Move extcon code into separate functions in preparation for addition of USB TYPE-C support. No functional change.
Signed-off-by Marek Vasut <[email protected]>
Quoted 136 lines
---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]--- drivers/extcon/extcon-usbc-tusb320.c | 75 +++++++++++++++++----------- 1 file changed, 46 insertions(+), 29 deletions(-)drivers/extcon/extcon-usbc-tusb320.c +46
-29@@ -184,19 +184,9 @@ static struct tusb320_ops tusb320l_ops = { .get_revision = tusb320l_get_revision, }; -static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +static void tusb320_extcon_irq_handler (struct tusb320_priv *priv,u8 reg) { -struct tusb320_priv *priv = dev_id;int state, polarity; -unsigned reg; - -if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { -dev_err (priv->dev,"error during i2c read!\n" ); -return IRQ_NONE ; - } - -if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) -return IRQ_NONE ; state = (reg >>TUSB320_REG9_ATTACHED_STATE_SHIFT ) &TUSB320_REG9_ATTACHED_STATE_MASK ;@@ -219,6 +209,22 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)extcon_sync (priv->edev,EXTCON_USB_HOST ); priv->state = state; +} + +static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +{ +struct tusb320_priv *priv = dev_id; +unsigned int reg; + +if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { +dev_err (priv->dev,"error during i2c read!\n" ); +return IRQ_NONE ; + } + +if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) +return IRQ_NONE ; + +tusb320_extcon_irq_handler (priv, reg);regmap_write (priv->regmap,TUSB320_REG9 , reg);@@ -230,8 +236,32 @@ static const struct regmap_config tusb320_regmap_config = { .val_bits = 8, }; -static int tusb320_extcon_probe (struct i2c_client *client, -const struct i2c_device_id *id) +static int tusb320_extcon_probe (struct tusb320_priv *priv) +{ +int ret; + + priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); +if (IS_ERR (priv->edev)) { +dev_err (priv->dev,"failed to allocate extcon device\n" ); +return PTR_ERR (priv->edev); + } + + ret =devm_extcon_dev_register (priv->dev, priv->edev); +if (ret <0 ) { +dev_err (priv->dev,"failed to register extcon device\n" ); +return ret; + } + +extcon_set_property_capability (priv->edev,EXTCON_USB , +EXTCON_PROP_USB_TYPEC_POLARITY ); +extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , +EXTCON_PROP_USB_TYPEC_POLARITY ); + +return 0 ; +} + +static int tusb320_probe (struct i2c_client *client, +const struct i2c_device_id *id) {struct tusb320_priv *priv;const void *match_data;@@ -257,12 +287,6 @@ static int tusb320_extcon_probe(struct i2c_client *client, priv->ops = (struct tusb320_ops *)match_data; - priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); -if (IS_ERR (priv->edev)) { -dev_err (priv->dev,"failed to allocate extcon device\n" ); -return PTR_ERR (priv->edev); - } -if (priv->ops->get_revision) { ret = priv->ops->get_revision (priv, &revision);if (ret)@@ -272,16 +296,9 @@ static int tusb320_extcon_probe(struct i2c_client *client,dev_info (priv->dev,"chip revision %d\n" , revision); } - ret =devm_extcon_dev_register (priv->dev, priv->edev); -if (ret <0 ) { -dev_err (priv->dev,"failed to register extcon device\n" ); + ret =tusb320_extcon_probe (priv); +if (ret)return ret; - } - -extcon_set_property_capability (priv->edev,EXTCON_USB , -EXTCON_PROP_USB_TYPEC_POLARITY ); -extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , -EXTCON_PROP_USB_TYPEC_POLARITY );/* update initial state */ tusb320_irq_handler (client->irq, priv);@@ -313,7 +330,7 @@ static const struct of_device_id tusb320_extcon_dt_match[] = {MODULE_DEVICE_TABLE (of, tusb320_extcon_dt_match);static struct i2c_driver tusb320_extcon_driver = { - .probe = tusb320_extcon_probe, + .probe = tusb320_probe, .driver = { .name ="extcon-tusb320" , .of_match_table = tusb320_extcon_dt_match,Signature · 1 line
2.35.1
Signature · 1 line
heikki
Chanwoo Choi
AppliedQuoted 130 lines · Marek Vasut
Move extcon code into separate functions in preparation for addition of USB TYPE-C support. No functional change.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Chanwoo Choi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Heikki Krogerus <[email protected]>
Cc: Yassine Oudjana <[email protected]>
To: [email protected]--- drivers/extcon/extcon-usbc-tusb320.c | 75 +++++++++++++++++----------- 1 file changed, 46 insertions(+), 29 deletions(-)drivers/extcon/extcon-usbc-tusb320.c +45
-28@@ -184,19 +184,9 @@ static struct tusb320_ops tusb320l_ops = { .get_revision = tusb320l_get_revision, }; -static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +static void tusb320_extcon_irq_handler (struct tusb320_priv *priv,u8 reg) { -struct tusb320_priv *priv = dev_id;int state, polarity; -unsigned reg; - -if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { -dev_err (priv->dev,"error during i2c read!\n" ); -return IRQ_NONE ; - } - -if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) -return IRQ_NONE ; state = (reg >>TUSB320_REG9_ATTACHED_STATE_SHIFT ) &TUSB320_REG9_ATTACHED_STATE_MASK ;@@ -219,6 +209,22 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)extcon_sync (priv->edev,EXTCON_USB_HOST ); priv->state = state; +} + +static irqreturn_t tusb320_irq_handler (int irq,void *dev_id) +{ +struct tusb320_priv *priv = dev_id; +unsigned int reg; + +if (regmap_read (priv->regmap,TUSB320_REG9 , ®)) { +dev_err (priv->dev,"error during i2c read!\n" ); +return IRQ_NONE ; + } + +if (!(reg &TUSB320_REG9_INTERRUPT_STATUS )) +return IRQ_NONE ; + +tusb320_extcon_irq_handler (priv, reg);regmap_write (priv->regmap,TUSB320_REG9 , reg);@@ -230,8 +236,32 @@ static const struct regmap_config tusb320_regmap_config = { .val_bits = 8, }; -static int tusb320_extcon_probe (struct i2c_client *client, -const struct i2c_device_id *id) +static int tusb320_extcon_probe (struct tusb320_priv *priv) +{ +int ret; + + priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); +if (IS_ERR (priv->edev)) { +dev_err (priv->dev,"failed to allocate extcon device\n" ); +return PTR_ERR (priv->edev); + } + + ret =devm_extcon_dev_register (priv->dev, priv->edev); +if (ret <0 ) { +dev_err (priv->dev,"failed to register extcon device\n" ); +return ret; + } + +extcon_set_property_capability (priv->edev,EXTCON_USB , +EXTCON_PROP_USB_TYPEC_POLARITY ); +extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , +EXTCON_PROP_USB_TYPEC_POLARITY ); + +return 0 ; +} + +static int tusb320_probe (struct i2c_client *client, +const struct i2c_device_id *id) {struct tusb320_priv *priv;const void *match_data;@@ -257,12 +287,6 @@ static int tusb320_extcon_probe(struct i2c_client *client, priv->ops = (struct tusb320_ops *)match_data; - priv->edev =devm_extcon_dev_allocate (priv->dev, tusb320_extcon_cable); -if (IS_ERR (priv->edev)) { -dev_err (priv->dev,"failed to allocate extcon device\n" ); -return PTR_ERR (priv->edev); - } -if (priv->ops->get_revision) { ret = priv->ops->get_revision (priv, &revision);if (ret)@@ -272,16 +296,9 @@ static int tusb320_extcon_probe(struct i2c_client *client,dev_info (priv->dev,"chip revision %d\n" , revision); } - ret =devm_extcon_dev_register (priv->dev, priv->edev); -if (ret <0 ) { -dev_err (priv->dev,"failed to register extcon device\n" ); + ret =tusb320_extcon_probe (priv); +if (ret)return ret; - } - -extcon_set_property_capability (priv->edev,EXTCON_USB , -EXTCON_PROP_USB_TYPEC_POLARITY ); -extcon_set_property_capability (priv->edev,EXTCON_USB_HOST , -EXTCON_PROP_USB_TYPEC_POLARITY );/* update initial state */ tusb320_irq_handler (client->irq, priv);
drivers/extcon/extcon-usbc-tusb320.c static const struct of_device_id tusb320_extcon_dt_match[] = { · line 336
Quoted 8 lines
drivers/extcon/extcon-usbc-tusb320.c +1
-1@@ -313,7 +330,7 @@ static const struct of_device_id tusb320_extcon_dt_match[] = {MODULE_DEVICE_TABLE (of, tusb320_extcon_dt_match);static struct i2c_driver tusb320_extcon_driver = { - .probe = tusb320_extcon_probe, + .probe = tusb320_probe, .driver = { .name ="extcon-tusb320" , .of_match_table = tusb320_extcon_dt_match,
Applied it. Thanks.
Signature · 3 lines
Best Regards, Samsung Electronics Chanwoo Choi