Skip to contentSkip to conversation

drm: bridge: icn6211: Add and use hs_rate and lp_rate

PATCH In review Marek Vasut 2 participants 2 messages Aug 1, 2022 – Aug 26, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm: bridge: icn6211: Add and use hs_rate and lp_rate

Fill in hs_rate and lp_rate to struct mipi_dsi_device for this bridge and adjust DSI input frequency calculations such that they expect the DSI host to configure HS clock according to hs_rate.

This is an optimization for the DSI burst mode case. In case the DSI device supports DSI burst mode, it is recommended to operate the DSI interface at the highest possible HS clock frequency which the DSI device supports. This permits the DSI host to send as short as possible bursts of data on the DSI link and keep the DSI data lanes in LP mode otherwise, which reduces power consumption.

Cc Jagan Teki <[email protected]>
Cc Laurent Pinchart <[email protected]>
Cc Linus Walleij <[email protected]>
Cc Robert Foss <[email protected]>
Cc Sam Ravnborg <[email protected]>
---
 drivers/gpu/drm/bridge/chipone-icn6211.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/gpu/drm/bridge/chipone-icn6211.c +4 -3
index 481c86b2406e8..65966f280cf4e 100644
@@ -259,7 +259,7 @@ static void chipone_configure_pll(struct chipone *icn,
 
 	/*
 	 * DSI byte clock frequency (input into PLL) is calculated as:
-	 *  DSI_CLK = mode clock * bpp / dsi_data_lanes / 8
+	 *  DSI_CLK = HS clock / 4
 	 *
 	 * DPI pixel clock frequency (output from PLL) is mode clock.
 	 *
@@ -273,8 +273,7 @@ static void chipone_configure_pll(struct chipone *icn,
 	 * It seems the PLL input clock after applying P pre-divider have
 	 * to be lower than 20 MHz.
 	 */
-	fin = mode_clock * mipi_dsi_pixel_format_to_bpp(icn->dsi->format) /
-	      icn->dsi->lanes / 8; /* in Hz */
+	fin = icn->dsi->hs_rate / 4; /* in Hz */
 
 	/* Minimum value of P predivider for PLL input in 5..20 MHz */
 	p_min = clamp(DIV_ROUND_UP(fin, 20000000), 1U, 31U);
@@ -515,6 +514,8 @@ static int chipone_dsi_attach(struct chipone *icn)
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
 			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
+	dsi->hs_rate = 500000000;
+	dsi->lp_rate = 16000000;
 
 	ret = mipi_dsi_attach(dsi);
 	if (ret < 0)
Signature · 1 line
2.35.1
#1 lore raw
Quoted 11 lines · Marek Vasut

Fill in hs_rate and lp_rate to struct mipi_dsi_device for this bridge and adjust DSI input frequency calculations such that they expect the DSI host to configure HS clock according to hs_rate.

This is an optimization for the DSI burst mode case. In case the DSI device supports DSI burst mode, it is recommended to operate the DSI interface at the highest possible HS clock frequency which the DSI device supports. This permits the DSI host to send as short as possible bursts of data on the DSI link and keep the DSI data lanes in LP mode otherwise, which reduces power consumption.

Quoted 7 lines
Cc Jagan Teki <[email protected]>
Cc Laurent Pinchart <[email protected]>
Cc Linus Walleij <[email protected]>
Cc Robert Foss <[email protected]>
Cc Sam Ravnborg <[email protected]>

LGTM so patch applied to drm-misc-next

Yours,
Linus Walleij