net: dsa: microchip: vlan configuration for bridge_vlan_unaware ports
cover net: dsa: microchip: vlan configuration for bridge_vlan_unaware ports
During refactoring of ksz spi probe, ds->configure_vlan_while_filtering flag is set in the ksz_setup function. It makes the extack warning when vlan_add command is used when vlan_filtering is turned off for the port.
To allow the vlan_add for the bridge vlan unaware ports, private pvid is used for it. This pvid is used for the vlan_unaware ports. The private pvid is added to the vlan_table during the port_setup function.
For the vlan aware ports, pvid issued by the user application will be used. Bridge vlan pvid is stored in the ksz port structure which can be used during transition between the vlan aware to unaware and vice versa.
Tested using the following sequence for ksz9477 and lan937x
----------------
Setup -> Host1 --- LAN1 -- LAN2 --- Host2
ip link set dev br0 type bridge vlan_filtering 0
bridge vlan add vid 5 dev lan1 pvid untagged
bridge vlan add vid 5 dev lan2 pvid untagged
bridge vlan del vid 5 dev lan1
bridge vlan del vid 5 dev lan2
After each step of execution, transmitted the packets from Host1 and successfully received by the Host2.
Arun Ramadoss (4):
net: dsa: microchip: modify vlan_add function prototype
net: dsa: microchip: lan937x: remove vlan_filtering_is_global flag
net: dsa: microchip: common ksz pvid get and set function
net: dsa: microchip: use private pvid for bridge_vlan_unwaware
drivers/net/dsa/microchip/ksz8.h | 6 +- drivers/net/dsa/microchip/ksz8795.c | 42 +++------- drivers/net/dsa/microchip/ksz9477.c | 40 ++++------ drivers/net/dsa/microchip/ksz9477.h | 5 +- drivers/net/dsa/microchip/ksz_common.c | 98 +++++++++++++++++++++++- drivers/net/dsa/microchip/ksz_common.h | 21 ++++- drivers/net/dsa/microchip/lan937x_main.c | 5 -- 7 files changed, 142 insertions(+), 75 deletions(-)
base-commit: ba323f6bee1d1e70aed280f8c89ac06959559855
Signature · 1 line
2.36.1
RFC PATCH 1/4 net: dsa: microchip: modify vlan_add function prototype
To use the vlan_add from the function other the .port_vlan_add dsa hook, changed the ksz8_vlan_add and ksz9477_vlan_del function prototype which uses only the vlan->vid and vlan->flags.
--- drivers/net/dsa/microchip/ksz8.h | 5 ++--- drivers/net/dsa/microchip/ksz8795.c | 19 +++++++++---------- drivers/net/dsa/microchip/ksz9477.c | 25 ++++++++++--------------- drivers/net/dsa/microchip/ksz9477.h | 4 +--- drivers/net/dsa/microchip/ksz_common.c | 2 +- drivers/net/dsa/microchip/ksz_common.h | 4 +--- 6 files changed, 24 insertions(+), 35 deletions(-)
drivers/net/dsa/microchip/ksz8.h +2 -3
@@ -38,9 +38,8 @@ int ksz8_mdb_del(struct ksz_device *dev, int port, const struct switchdev_obj_port_mdb *mdb, struct dsa_db db);int ksz8_port_vlan_filtering (struct ksz_device *dev,int port,bool flag,struct netlink_ext_ack *extack); -int ksz8_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack); +int ksz8_port_vlan_add (struct ksz_device *dev,int port,u16 vlan_vid, +u16 flags);int ksz8_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); int ksz8_port_mirror_add(struct ksz_device *dev, int port,
drivers/net/dsa/microchip/ksz8795.c +9 -10
@@ -962,11 +962,10 @@ static void ksz8_port_enable_pvid(struct ksz_device *dev, int port, bool state) } } -int ksz8_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack) +int ksz8_port_vlan_add (struct ksz_device *dev,int port,u16 vlan_vid, +u16 flags) { -bool untagged = vlan->flags &BRIDGE_VLAN_INFO_UNTAGGED ; +bool untagged = flags &BRIDGE_VLAN_INFO_UNTAGGED ;struct ksz_port *p = &dev->ports[port];u16 data, new_pvid =0 ;u8 fid, member, valid;
@@ -979,7 +978,7 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port,* Ignore VID 0, which is always untagged. * Ignore CPU port, which will always be tagged. */ -if (untagged != p->remove_tag && vlan->vid !=0 && +if (untagged != p->remove_tag && vlan_vid !=0 && port != dev->cpu_port) {unsigned int vid;
@@ -989,7 +988,7 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port,*/ for (vid =1 ; vid < dev->info->num_vlans; ++vid) {/* Skip the VID we are going to add or reconfigure */ -if (vid == vlan->vid) +if (vid == vlan_vid)continue ; ksz8_from_vlan(dev, dev->vlan_cache[vid].table[0],
@@ -1002,7 +1001,7 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, p->remove_tag = untagged; } -ksz8_r_vlan_table (dev, vlan->vid, &data); +ksz8_r_vlan_table (dev, vlan_vid, &data);ksz8_from_vlan (dev, data, &fid, &member, &valid);/* First time to setup the VLAN entry. */
@@ -1014,11 +1013,11 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, member |=BIT (port);ksz8_to_vlan (dev, fid, member, valid, &data); -ksz8_w_vlan_table (dev, vlan->vid, data); +ksz8_w_vlan_table (dev, vlan_vid, data);/* change PVID */ -if (vlan->flags &BRIDGE_VLAN_INFO_PVID ) - new_pvid = vlan->vid; +if (flags &BRIDGE_VLAN_INFO_PVID ) + new_pvid = vlan_vid;if (new_pvid) {u16 vid;
drivers/net/dsa/microchip/ksz9477.c +10 -15
@@ -370,21 +370,18 @@ int ksz9477_port_vlan_filtering(struct ksz_device *dev, int port,return 0 ; } -int ksz9477_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack) +int ksz9477_port_vlan_add (struct ksz_device *dev,int port,u16 vlan_vid, +u16 flags) {u32 vlan_table[3 ]; -bool untagged = vlan->flags &BRIDGE_VLAN_INFO_UNTAGGED ; +bool untagged = flags &BRIDGE_VLAN_INFO_UNTAGGED ;int err; - err =ksz9477_get_vlan_table (dev, vlan->vid, vlan_table); -if (err) { -NL_SET_ERR_MSG_MOD (extack,"Failed to get vlan table" ); + err =ksz9477_get_vlan_table (dev, vlan_vid, vlan_table); +if (err)return err; - } - vlan_table[0 ] =VLAN_VALID | (vlan->vid &VLAN_FID_M ); + vlan_table[0 ] =VLAN_VALID | (vlan_vid &VLAN_FID_M );if (untagged) vlan_table[1 ] |=BIT (port);else
@@ -393,15 +390,13 @@ int ksz9477_port_vlan_add(struct ksz_device *dev, int port, vlan_table[2 ] |=BIT (port) |BIT (dev->cpu_port); - err =ksz9477_set_vlan_table (dev, vlan->vid, vlan_table); -if (err) { -NL_SET_ERR_MSG_MOD (extack,"Failed to set vlan table" ); + err =ksz9477_set_vlan_table (dev, vlan_vid, vlan_table); +if (err)return err; - }/* change PVID */ -if (vlan->flags &BRIDGE_VLAN_INFO_PVID ) -ksz_pwrite16 (dev, port,REG_PORT_DEFAULT_VID , vlan->vid); +if (flags &BRIDGE_VLAN_INFO_PVID ) +ksz_pwrite16 (dev, port,REG_PORT_DEFAULT_VID , vlan_vid);return 0 ; }
drivers/net/dsa/microchip/ksz9477.h +1 -3
@@ -25,9 +25,7 @@ void ksz9477_freeze_mib(struct ksz_device *dev, int port, bool freeze);void ksz9477_port_init_cnt (struct ksz_device *dev,int port);int ksz9477_port_vlan_filtering (struct ksz_device *dev,int port,bool flag,struct netlink_ext_ack *extack); -int ksz9477_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack); +int ksz9477_port_vlan_add (struct ksz_device *dev,int port,u16 vid,u16 flags);int ksz9477_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); int ksz9477_port_mirror_add(struct ksz_device *dev, int port,
drivers/net/dsa/microchip/ksz_common.c +1 -1
@@ -1351,7 +1351,7 @@ static int ksz_port_vlan_add(struct dsa_switch *ds, int port,if (!dev->dev_ops->vlan_add)return -EOPNOTSUPP ; -return dev->dev_ops->vlan_add (dev, port, vlan, extack); +return dev->dev_ops->vlan_add (dev, port, vlan->vid, vlan->flags); } static int ksz_port_vlan_del(struct dsa_switch *ds, int port,
drivers/net/dsa/microchip/ksz_common.h +1 -3
@@ -267,9 +267,7 @@ struct ksz_dev_ops {void (*r_mib_stat64)(struct ksz_device *dev,int port);int (*vlan_filtering)(struct ksz_device *dev,int port,bool flag,struct netlink_ext_ack *extack); -int (*vlan_add)(struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack); +int (*vlan_add)(struct ksz_device *dev,int port,u16 vid,u16 flags);int (*vlan_del)(struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); int (*mirror_add)(struct ksz_device *dev, int port,
Signature · 1 line
2.36.1
Vladimir Oltean
maintainerRe: [Patch RFC net-next 1/4] net: dsa: microchip: modify vlan_add function prototype
drivers/net/dsa/microchip/ksz8.h int ksz8_mdb_del(struct ksz_device *dev, int port, · line 41
Quoted 12 lines · Arun Ramadoss
drivers/net/dsa/microchip/ksz8.h +1
-3@@ -38,9 +38,8 @@ int ksz8_mdb_del(struct ksz_device *dev, int port, const struct switchdev_obj_port_mdb *mdb, struct dsa_db db);int ksz8_port_vlan_filtering (struct ksz_device *dev,int port,bool flag,struct netlink_ext_ack *extack); -int ksz8_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack); +int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid,
I don't see an impediment to naming "vlan_vid" just "vid".
drivers/net/dsa/microchip/ksz8.h int ksz8_mdb_del(struct ksz_device *dev, int port, · line 44
Quoted 3 lines
drivers/net/dsa/microchip/ksz8.h +1
-0+ u16 flags);int ksz8_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan);
Won't you convert vlan_del too?
Re: [Patch RFC net-next 1/4] net: dsa: microchip: modify vlan_add function prototype
Hi Vladimir,
Thanks for the comment
Quoted 15 lines · Vladimir Oltean
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 11 lines · Arun Ramadoss
drivers/net/dsa/microchip/ksz8.h +0
-0@@ -38,9 +38,8 @@ int ksz8_mdb_del(struct ksz_device *dev, int port, const struct switchdev_obj_port_mdb *mdb, struct dsa_db db); int ksz8_port_vlan_filtering(struct ksz_device *dev, int port, bool flag,
Quoted 8 lines
Quoted 6 lines
drivers/net/dsa/microchip/ksz8.h +1
-3struct netlink_ext_ack *extack); -int ksz8_port_vlan_add (struct ksz_device *dev,int port, -const struct switchdev_obj_port_vlan *vlan, -struct netlink_ext_ack *extack); +int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16
vlan_vid,I don't see an impediment to naming "
vlan_vid" just "vid".
Ok, I will name it as vid.
Quoted 6 lines
Quoted 4 lines
+ u16 flags);
int ksz8_port_vlan_del(structksz_device*dev, int port,const struct switchdev_obj_port_vlan *vlan);Won't you convert
vlan_deltoo?
I will change it too.
RFC PATCH 2/4 net: dsa: microchip: lan937x: remove vlan_filtering_is_global flag
In reply to Arun RamadossTo have the similar implementation among the ksz switches, removed the vlan_filtering_is_global flag which is only present in the lan937x.
--- drivers/net/dsa/microchip/lan937x_main.c | 5 ----- 1 file changed, 5 deletions(-)
drivers/net/dsa/microchip/lan937x_main.c +0 -5
@@ -401,11 +401,6 @@ int lan937x_setup(struct dsa_switch *ds)return ret; } -/* The VLAN aware is a global setting. Mixed vlan -* filterings are not supported. -*/ - ds->vlan_filtering_is_global = true; -/* Enable aggressive back off for half duplex & UNH mode */ lan937x_cfg(dev, REG_SW_MAC_CTRL_0, (SW_PAUSE_UNH_MODE | SW_NEW_BACKOFF | SW_AGGR_BACKOFF),
Signature · 1 line
2.36.1
Vladimir Oltean
maintainerRe: [Patch RFC net-next 2/4] net: dsa: microchip: lan937x: remove vlan_filtering_is_global flag
Quoted 13 lines · Arun Ramadoss
To have the similar implementation among the ksz switches, removed the
vlan_filtering_is_globalflag which is only present in the lan937x.Signed-off-by Arun Ramadoss <[email protected]>--- drivers/net/dsa/microchip/lan937x_main.c | 5 ----- 1 file changed, 5 deletions(-)drivers/net/dsa/microchip/lan937x_main.c +0
-0
drivers/net/dsa/microchip/lan937x_main.c int lan937x_setup(struct dsa_switch *ds) · line 408
Quoted 8 lines
drivers/net/dsa/microchip/lan937x_main.c +0
-5@@ -401,11 +401,6 @@ int lan937x_setup(struct dsa_switch *ds)return ret; } -/* The VLAN aware is a global setting. Mixed vlan -* filterings are not supported. -*/ - ds->vlan_filtering_is_global = true; -
You understand what this flag does, right? It ensures that if you have lan0 and lan1 under VLAN-aware br0, then lan2 which is standalone will declare NETIF_F_HW_VLAN_CTAG_FILTER. In turn, this makes the network stack know that lan2 won't accept VLAN-tagged packets unless there is an 8021q interface with the given VID on top of it. This 8021q interface calls vlan_vid_add() to populate the driver's VLAN RX filter with its VID, and this gets translated into dsa_slave_vlan_rx_add_vid() which ultimately reaches the driver's ->port_vlan_add() function.
If VLAN filtering *is* a global setting, and looking at this call from ksz9477_port_vlan_filtering() which is not per port, I'd say it is:
ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE, true);
then what would happen is that all VLAN tagged traffic would be dropped on the standalone lan2.
I'd say that the ksz9477 is buggy for not declaring vlan_filtering_is_global, rather than encouraging you to delete it from lan937x. In turn, fixing ksz9477 would make setting this flag from a common location possible, because ksz8 needs it too.
Re: [Patch RFC net-next 2/4] net: dsa: microchip: lan937x: remove vlan_filtering_is_global flag
Hi Vladimir,
Thanks for the comment.
Quoted 51 lines · Vladimir Oltean
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 15 lines · Arun Ramadoss
To have the similar implementation among the ksz switches, removed the
vlan_filtering_is_globalflag which is only present in the lan937x.Signed-off-by Arun Ramadoss <[email protected]>--- drivers/net/dsa/microchip/lan937x_main.c | 5 ----- 1 file changed, 5 deletions(-)drivers/net/dsa/microchip/lan937x_main.c +0
-0drivers/net/dsa/microchip/lan937x_main.c int lan937x_setup(struct dsa_switch *ds) · line 408
Quoted 8 lines
drivers/net/dsa/microchip/lan937x_main.c +0
-5@@ -401,11 +401,6 @@ int lan937x_setup(struct dsa_switch *ds)return ret; } -/* The VLAN aware is a global setting. Mixed vlan -* filterings are not supported. -*/ - ds->vlan_filtering_is_global = true; -You understand what this flag does, right? It ensures that if you have
lan0 and lan1 under VLAN-aware br0, then lan2 which is standalone will
declareNETIF_F_HW_VLAN_CTAG_FILTER. In turn, this makes the network stack know that lan2 won't accept VLAN-tagged packets unless there is an
8021q interface with the given VID on top of it. This 8021q interface callsvlan_vid_add()to populate the driver's VLAN RX filter with its VID, and this gets translated intodsa_slave_vlan_rx_add_vid()which ultimately reaches the driver's ->port_vlan_add() function.If VLAN filtering *is* a global setting, and looking at this call from
ksz9477_port_vlan_filtering()which is not per port, I'd say it is:ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE,true);
then what would happen is that all VLAN tagged traffic would be dropped
on the standalone lan2.
Quoted 6 lines
I'd say that the ksz9477 is buggy for not declaring
vlan_filtering_is_global,
rather than encouraging you to delete it from lan937x. In turn, fixing
ksz9477 would make setting this flag from a common location possible, because ksz8 needs it too.
I have done some study on this SW_VLAN_ENABLE bit. By default the pvid of the port is 1 and vlan port membership (0xNA04) is 0xff. So if the bit is 0, then unknown dest addr packets are broadcasted which is the default behaviour of switch.
Now consider when the bit is 1,
- If the invalid vlan packet is received, then based on drop invalid vid or unknown vid forward bit, packets are discarded or forwarded.
- If the valid vlan packet is received, then broadcast to ports in vlan port membership list.
The port membership register set using the ksz9477_cfg_port_member function.
In summary, I infer that we can enable this bit in the port_setup and based on the port membership packets can be forwarded. Is my understanding correct?
Can I remove this patch from this series and submit as the separate one?
Vladimir Oltean
maintainerRe: [Patch RFC net-next 2/4] net: dsa: microchip: lan937x: remove vlan_filtering_is_global flag
Quoted 8 lines · On Tue, Aug 02, 2022 at 04:09:35PM +0000, [email protected] wrote:
I have done some study on this
SW_VLAN_ENABLEbit. By default the pvid of the port is 1 and vlan port membership (0xNA04) is0xff. So if the bit is 0, then unknown dest addr packets are broadcasted which is the default behaviour of switch.
Now consider when the bit is 1,
- If the invalid vlan packet is received, then based on drop invalid vid or unknown vid forward bit, packets are discarded or forwarded.
- If the valid vlan packet is received, then broadcast to ports in vlan
Quoted 8 lines
port membership list.
The port membership register set using theksz9477_cfg_port_memberfunction.
In summary, I infer that we can enable this bit in theport_setupand based on the port membership packets can be forwarded. Is my understanding correct?
Can I remove this patch from this series and submit as the separate one?
I'm not sure that the switch's capabilities are quite in line with the Linux kernel expectations if you always force the 802.1Q VLAN Enable bit to true.
I am looking at Table 4-8: VLAN forwarding from the KSZ9563 datasheet, and it says that when the "Unknown VID forward" bit is set and we are in VLAN enable mode, packets are forwarded to the Unknown VID packet forward list regardless of ALU match (which is "don't care" in this table). In essence this is because the switch failed to resolve the unknown VID to a FID. Other switches have a default FID for this case, but it doesn't appear to hold true for KSZ.
The last thing you want is for packets under a VLAN-unaware bridge to be always flooded to the ports in the Unknown VID packet forward list, and bypass ALU lookups.
RFC PATCH 3/4 net: dsa: microchip: common ksz pvid get and set function
In reply to Arun RamadossAdd the helper function for getting and setting the pvid which will be common for all ksz switches
--- drivers/net/dsa/microchip/ksz8795.c | 8 ++------ drivers/net/dsa/microchip/ksz9477.c | 6 +++--- drivers/net/dsa/microchip/ksz_common.c | 21 +++++++++++++++++++++ drivers/net/dsa/microchip/ksz_common.h | 11 +++++++++++ 4 files changed, 37 insertions(+), 9 deletions(-)
drivers/net/dsa/microchip/ksz8795.c +2 -6
@@ -1020,12 +1020,8 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid, new_pvid = vlan_vid;if (new_pvid) { -u16 vid; -ksz_pread16 (dev, port,REG_PORT_CTRL_VID , &vid); - vid &= ~VLAN_VID_MASK ; - vid |= new_pvid; -ksz_pwrite16 (dev, port,REG_PORT_CTRL_VID , vid); +ksz_set_pvid (dev, port, new_pvid);ksz8_port_enable_pvid (dev, port, true); }
@@ -1042,7 +1038,7 @@ int ksz8_port_vlan_del(struct ksz_device *dev, int port,if (ksz_is_ksz88x3 (dev))return -ENOTSUPP ; -ksz_pread16 (dev, port,REG_PORT_CTRL_VID , &pvid); +ksz_get_pvid (dev, port, &pvid); pvid = pvid &0xFFF ;ksz8_r_vlan_table (dev, vlan->vid, &data);
drivers/net/dsa/microchip/ksz9477.c +3 -3
@@ -396,7 +396,7 @@ int ksz9477_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid,/* change PVID */ if (flags &BRIDGE_VLAN_INFO_PVID ) -ksz_pwrite16 (dev, port,REG_PORT_DEFAULT_VID , vlan_vid); +ksz_set_pvid (dev, port, vlan_vid);return 0 ; }
@@ -408,7 +408,7 @@ int ksz9477_port_vlan_del(struct ksz_device *dev, int port,u32 vlan_table[3 ];u16 pvid; -ksz_pread16 (dev, port,REG_PORT_DEFAULT_VID , &pvid); +ksz_get_pvid (dev, port, &pvid); pvid = pvid &0xFFF ;if (ksz9477_get_vlan_table (dev, vlan->vid, vlan_table)) {
@@ -429,7 +429,7 @@ int ksz9477_port_vlan_del(struct ksz_device *dev, int port,return -ETIMEDOUT ; } -ksz_pwrite16 (dev, port,REG_PORT_DEFAULT_VID , pvid); +ksz_set_pvid (dev, port, pvid);return 0 ; }
drivers/net/dsa/microchip/ksz_common.c +21 -0
@@ -14,6 +14,7 @@#include <linux/phy.h> #include <linux/etherdevice.h> #include <linux/if_bridge.h> +#include <linux/if_vlan.h> #include <linux/of_device.h> #include <linux/of_net.h> #include <linux/micrel_phy.h>
@@ -258,6 +259,7 @@ static const u16 ksz8795_regs[] = { [S_MULTICAST_CTRL] = 0x04, [P_XMII_CTRL_0] = 0x06, [P_XMII_CTRL_1] = 0x56, + [P_DEFAULT_PVID] = 0x03, };static const u32 ksz8795_masks[] = {
@@ -330,6 +332,7 @@ static const u16 ksz8863_regs[] = { [S_START_CTRL] = 0x01, [S_BROADCAST_CTRL] = 0x06, [S_MULTICAST_CTRL] = 0x04, + [P_DEFAULT_PVID] = 0x03, };static const u32 ksz8863_masks[] = {
@@ -372,6 +375,7 @@ static const u16 ksz9477_regs[] = { [S_MULTICAST_CTRL] = 0x0331, [P_XMII_CTRL_0] = 0x0300, [P_XMII_CTRL_1] = 0x0301, + [P_DEFAULT_PVID] = 0x0000, };static const u32 ksz9477_masks[] = {
@@ -1331,6 +1335,23 @@ static enum dsa_tag_protocol ksz_get_tag_protocol(struct dsa_switch *ds,return proto; } +void ksz_get_pvid (struct ksz_device *dev,int port,u16 *pvid) +{ +const u16 *regs = dev->info->regs; +u16 val; + +ksz_pread16 (dev, port, regs[P_DEFAULT_PVID ], &val); + + *pvid = val &VLAN_VID_MASK ; +} + +void ksz_set_pvid (struct ksz_device *dev,int port,u16 pvid) +{ +const u16 *regs = dev->info->regs; + +ksz_prmw16 (dev, port, regs[P_DEFAULT_PVID ],VLAN_VID_MASK , pvid); +} +static int ksz_port_vlan_filtering (struct dsa_switch *ds,int port,bool flag,struct netlink_ext_ack *extack) {
drivers/net/dsa/microchip/ksz_common.h +11 -0
@@ -175,6 +175,7 @@ enum ksz_regs {S_MULTICAST_CTRL ,P_XMII_CTRL_0 ,P_XMII_CTRL_1 , + P_DEFAULT_PVID, }; enum ksz_masks {
@@ -319,6 +320,8 @@ void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);bool ksz_get_gbit (struct ksz_device *dev,int port);phy_interface_t ksz_get_xmii (struct ksz_device *dev,int port,bool gbit);extern const struct ksz_chip_data ksz_switch_chips[]; +void ksz_get_pvid (struct ksz_device *dev,int port,u16 *pvid); +void ksz_set_pvid (struct ksz_device *dev,int port,u16 pvid);/* Common register access functions */
@@ -432,6 +435,14 @@ static inline void ksz_prmw8(struct ksz_device *dev, int port, int offset, mask, val); } +static inline void ksz_prmw16 (struct ksz_device *dev,int port,int offset, +u16 mask,u16 val) +{ +regmap_update_bits (dev->regmap[1 ], + dev->dev_ops->get_port_addr (port, offset), + mask, val); +} +static inline void ksz_regmap_lock (void *__mtx) {struct mutex *mtx = __mtx;
Signature · 1 line
2.36.1
Re: [Patch RFC net-next 3/4] net: dsa: microchip: common ksz pvid get and set function
Quoted 5 lines · Arun Ramadoss
Add the helper function for getting and setting the pvid which will be common for all ksz switches
Signed-off-by Arun Ramadoss <[email protected]>---
Re: [Patch RFC net-next 3/4] net: dsa: microchip: common ksz pvid get and set function
In reply to Arun RamadossQuoted 4 lines · Arun Ramadoss
Add the helper function for getting and setting the pvid which will be common for all ksz switches
Signed-off-by Arun Ramadoss <[email protected]>
--
Florian
RFC PATCH 4/4 net: dsa: microchip: use private pvid for bridge_vlan_unwaware
In reply to Arun RamadossTo remove ds->configure_vlan_while_not_filtering, for the bridge vlan unaware the private pvid of 4095 is used. The bridged vlan pvid is stored in the ksz port structure and it is used only when vlan_filtering is enabled. If vlan_filtering is disabled then private pvid is used.
--- drivers/net/dsa/microchip/ksz8.h | 1 + drivers/net/dsa/microchip/ksz8795.c | 23 +------- drivers/net/dsa/microchip/ksz9477.c | 19 ++---- drivers/net/dsa/microchip/ksz9477.h | 1 + drivers/net/dsa/microchip/ksz_common.c | 81 ++++++++++++++++++++++++-- drivers/net/dsa/microchip/ksz_common.h | 10 +++- 6 files changed, 95 insertions(+), 40 deletions(-)
drivers/net/dsa/microchip/ksz8.h +1 -0
@@ -42,6 +42,7 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid, u16 flags);int ksz8_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); +void ksz8_port_enable_pvid (struct ksz_device *dev,int port,bool state);int ksz8_port_mirror_add (struct ksz_device *dev,int port,struct dsa_mall_mirror_tc_entry *mirror,bool ingress,struct netlink_ext_ack *extack);
drivers/net/dsa/microchip/ksz8795.c +3 -20
@@ -952,7 +952,7 @@ int ksz8_port_vlan_filtering(struct ksz_device *dev, int port, bool flag,return 0 ; } -static void ksz8_port_enable_pvid (struct ksz_device *dev,int port,bool state) +void ksz8_port_enable_pvid (struct ksz_device *dev,int port,bool state) {if (ksz_is_ksz88x3 (dev)) { ksz_cfg(dev, REG_SW_INSERT_SRC_PVID,
@@ -967,8 +967,8 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid, {bool untagged = flags &BRIDGE_VLAN_INFO_UNTAGGED ;struct ksz_port *p = &dev->ports[port]; -u16 data, new_pvid =0 ;u8 fid, member, valid; +u16 data;if (ksz_is_ksz88x3 (dev))return -ENOTSUPP ;
@@ -1015,32 +1015,18 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid,ksz8_to_vlan (dev, fid, member, valid, &data);ksz8_w_vlan_table (dev, vlan_vid, data); -/* change PVID */ -if (flags &BRIDGE_VLAN_INFO_PVID ) - new_pvid = vlan_vid; - -if (new_pvid) { - -ksz_set_pvid (dev, port, new_pvid); - -ksz8_port_enable_pvid (dev, port, true); - } -return 0 ; }int ksz8_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan) { -u16 data, pvid; +u16 data;u8 fid, member, valid;if (ksz_is_ksz88x3 (dev))return -ENOTSUPP ; -ksz_get_pvid (dev, port, &pvid); - pvid = pvid &0xFFF ; -ksz8_r_vlan_table (dev, vlan->vid, &data);ksz8_from_vlan (dev, data, &fid, &member, &valid);
@@ -1055,9 +1041,6 @@ int ksz8_port_vlan_del(struct ksz_device *dev, int port,ksz8_to_vlan (dev, fid, member, valid, &data);ksz8_w_vlan_table (dev, vlan->vid, data); -if (pvid == vlan->vid) -ksz8_port_enable_pvid (dev, port, false); -return 0 ; }
drivers/net/dsa/microchip/ksz9477.c +6 -13
@@ -354,6 +354,12 @@ void ksz9477_flush_dyn_mac_table(struct ksz_device *dev, int port) } } +void ksz9477_port_drop_untagged (struct ksz_device *dev,int port,bool state) +{ +ksz_port_cfg (dev, port,REG_PORT_MRI_MAC_CTRL ,PORT_DROP_NON_VLAN , + state); +} +int ksz9477_port_vlan_filtering (struct ksz_device *dev,int port,bool flag,struct netlink_ext_ack *extack) {
@@ -394,10 +400,6 @@ int ksz9477_port_vlan_add(struct ksz_device *dev, int port, u16 vlan_vid,if (err)return err; -/* change PVID */ -if (flags &BRIDGE_VLAN_INFO_PVID ) -ksz_set_pvid (dev, port, vlan_vid); -return 0 ; }
@@ -406,10 +408,6 @@ int ksz9477_port_vlan_del(struct ksz_device *dev, int port, {bool untagged = vlan->flags &BRIDGE_VLAN_INFO_UNTAGGED ;u32 vlan_table[3 ]; -u16 pvid; - -ksz_get_pvid (dev, port, &pvid); - pvid = pvid &0xFFF ;if (ksz9477_get_vlan_table (dev, vlan->vid, vlan_table)) {dev_dbg (dev->dev,"Failed to get vlan table\n" );
@@ -418,9 +416,6 @@ int ksz9477_port_vlan_del(struct ksz_device *dev, int port, vlan_table[2 ] &= ~BIT (port); -if (pvid == vlan->vid) - pvid =1 ; -if (untagged) vlan_table[1 ] &= ~BIT (port);
@@ -429,8 +424,6 @@ int ksz9477_port_vlan_del(struct ksz_device *dev, int port,return -ETIMEDOUT ; } -ksz_set_pvid (dev, port, pvid); -return 0 ; }
drivers/net/dsa/microchip/ksz9477.h +1 -0
@@ -28,6 +28,7 @@ int ksz9477_port_vlan_filtering(struct ksz_device *dev, int port,int ksz9477_port_vlan_add (struct ksz_device *dev,int port,u16 vid,u16 flags);int ksz9477_port_vlan_del (struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); +void ksz9477_port_drop_untagged (struct ksz_device *dev,int port,bool state);int ksz9477_port_mirror_add (struct ksz_device *dev,int port,struct dsa_mall_mirror_tc_entry *mirror,bool ingress,struct netlink_ext_ack *extack);
drivers/net/dsa/microchip/ksz_common.c +76 -5
152 lines not on this page · raw message
drivers/net/dsa/microchip/ksz_common.h +8 -2
@@ -15,6 +15,7 @@#include <net/dsa.h> #define KSZ_MAX_NUM_PORTS 8 +#define KSZ_DEFAULT_VLAN (VLAN_N_VID - 1)struct vlan_table {u32 table[3 ];
@@ -63,6 +64,11 @@ struct ksz_chip_data {bool internal_phy[KSZ_MAX_NUM_PORTS ]; }; +struct ksz_vlan { +u16 vid; +bool valid; +}; +struct ksz_port {bool remove_tag;/* Remove Tag flag set, for ksz8795 only */ int stp_state;
@@ -81,6 +87,7 @@ struct ksz_port {u16 max_frame;u32 rgmii_tx_val;u32 rgmii_rx_val; +struct ksz_vlan bridge_pvid; };struct ksz_device {
@@ -271,6 +278,7 @@ struct ksz_dev_ops {int (*vlan_add)(struct ksz_device *dev,int port,u16 vid,u16 flags);int (*vlan_del)(struct ksz_device *dev,int port,const struct switchdev_obj_port_vlan *vlan); +void (*drop_untagged)(struct ksz_device *dev,int port,bool untagged);int (*mirror_add)(struct ksz_device *dev,int port,struct dsa_mall_mirror_tc_entry *mirror,bool ingress,struct netlink_ext_ack *extack);
@@ -320,8 +328,6 @@ void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);bool ksz_get_gbit (struct ksz_device *dev,int port);phy_interface_t ksz_get_xmii (struct ksz_device *dev,int port,bool gbit);extern const struct ksz_chip_data ksz_switch_chips[]; -void ksz_get_pvid (struct ksz_device *dev,int port,u16 *pvid); -void ksz_set_pvid (struct ksz_device *dev,int port,u16 pvid);/* Common register access functions */
Signature · 1 line
2.36.1
Vladimir Oltean
maintainerRe: [Patch RFC net-next 4/4] net: dsa: microchip: use private pvid for bridge_vlan_unwaware
drivers/net/dsa/microchip/ksz_common.c static const struct ksz_dev_ops ksz8_dev_ops = { · line 164
Quoted 9 lines · Arun Ramadoss
drivers/net/dsa/microchip/ksz_common.c +1
-0@@ -161,6 +161,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .vlan_filtering = ksz8_port_vlan_filtering, .vlan_add = ksz8_port_vlan_add, .vlan_del = ksz8_port_vlan_del, + .drop_untagged = ksz8_port_enable_pvid,
You'll have to explain this one. What impact does PVID insertion on KSZ8 have upon dropping/not dropping untagged packets? This patch is saying that when untagged packets should be dropped, PVID insertion should be enabled, and when untagged packets should be accepted, PVID insertion should be disabled. How come?
Quoted 20 lines
drivers/net/dsa/microchip/ksz_common.c +2
-0.mirror_add = ksz8_port_mirror_add, .mirror_del = ksz8_port_mirror_del, .get_caps = ksz8_get_caps,@@ -187,6 +188,7 @@ static const struct ksz_dev_ops ksz9477_dev_ops = { .vlan_filtering = ksz9477_port_vlan_filtering, .vlan_add = ksz9477_port_vlan_add, .vlan_del = ksz9477_port_vlan_del, + .drop_untagged = ksz9477_port_drop_untagged, .mirror_add = ksz9477_port_mirror_add, .mirror_del = ksz9477_port_mirror_del, .get_caps = ksz9477_get_caps,@@ -220,6 +222,7 @@ static const struct ksz_dev_ops lan937x_dev_ops = { .vlan_filtering = ksz9477_port_vlan_filtering, .vlan_add = ksz9477_port_vlan_add, .vlan_del = ksz9477_port_vlan_del, + .drop_untagged = ksz9477_port_drop_untagged, .mirror_add = ksz9477_port_mirror_add, .mirror_del = ksz9477_port_mirror_del, .get_caps = lan937x_phylink_get_caps,
drivers/net/dsa/microchip/ksz_common.c static int ksz_enable_port(struct dsa_switch *ds, int port, · line 1262
Quoted 6 lines
drivers/net/dsa/microchip/ksz_common.c +3
-0@@ -1254,6 +1257,9 @@ static int ksz_enable_port(struct dsa_switch *ds, int port, {struct ksz_device *dev = ds->priv; + dev->dev_ops->vlan_add (dev, port,KSZ_DEFAULT_VLAN , +BRIDGE_VLAN_INFO_UNTAGGED ); +
How many times can this be executed before the VLAN add operation fails due to the VLAN already being present on the port? I notice you're ignoring the return code. Wouldn't it be better to do this at port_setup() time instead?
(side note, the PVID for standalone mode can be added at port_setup time. The PVID to use for bridges in VLAN-unaware mode can be allocated at port_bridge_join time)
Quoted 8 lines
drivers/net/dsa/microchip/ksz_common.c +5
-0if (!dsa_is_user_port (ds, port))return 0 ; +static int ksz_commit_pvid (struct dsa_switch *ds,int port) +{ +struct dsa_port *dp =dsa_to_port (ds, port); +struct net_device *br =dsa_port_bridge_dev_get (dp); +struct ksz_device *dev = ds->priv;
drivers/net/dsa/microchip/ksz_common.c void ksz_get_pvid(struct ksz_device *dev, int port, u16 *pvid) · line 1375
Quoted 10 lines
drivers/net/dsa/microchip/ksz_common.c +10
-0+u16 pvid =KSZ_DEFAULT_VLAN ; +bool drop_untagged = false; +struct ksz_port *p; + + p = &dev->ports[port]; + +if (br &&br_vlan_enabled (br)) { + pvid = p->bridge_pvid.vid; + drop_untagged = !p->bridge_pvid.valid; + }
This is better in the sense that it resolves the need for the configure_vlan_while_not_filtering hack. But standalone and VLAN-unaware bridge ports still share the same PVID. Even more so, standalone ports have address learning enabled, which will poison the address database of VLAN-unaware bridge ports (and of other standalone ports):
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Are you going to do further work in this area?
Quoted 8 lines
drivers/net/dsa/microchip/ksz_common.c +8
-0+ +ksz_set_pvid (dev, port, pvid); + +if (dev->dev_ops->drop_untagged) + dev->dev_ops->drop_untagged (dev, port, drop_untagged); + +return 0 ; +}
Re: [Patch RFC net-next 4/4] net: dsa: microchip: use private pvid for bridge_vlan_unwaware
Quoted 16 lines · Vladimir Oltean
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
drivers/net/dsa/microchip/ksz_common.c static const struct ksz_dev_ops ksz8_dev_ops = · line 165
Quoted 11 lines · Arun Ramadoss
drivers/net/dsa/microchip/ksz_common.c +1
-0@@ -161,6 +161,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .vlan_filtering = ksz8_port_vlan_filtering, .vlan_add = ksz8_port_vlan_add, .vlan_del = ksz8_port_vlan_del, + .drop_untagged = ksz8_port_enable_pvid,
Quoted 8 lines
You'll have to explain this one. What impact does PVID insertion on KSZ8
have upon dropping/not dropping untagged packets? This patch is saying
that when untagged packets should be dropped, PVID insertion should be
enabled, and when untagged packets should be accepted, PVID insertion should be disabled. How come?
Its my mistake. I referred KSZ87xx datasheet but I couldn't find the register for the dropping the untagged packet. If that is the case, shall I remove the dropping of untagged packet feature from the ksz8 switches?
Quoted 37 lines
Quoted 23 lines
drivers/net/dsa/microchip/ksz_common.c +0
-0.mirror_add = ksz8_port_mirror_add, .mirror_del = ksz8_port_mirror_del,.get_caps = ksz8_get_caps,drivers/net/dsa/microchip/ksz_common.c +1
-0@@ -187,6 +188,7 @@ static const struct ksz_dev_ops ksz9477_dev_ops = { .vlan_filtering = ksz9477_port_vlan_filtering, .vlan_add = ksz9477_port_vlan_add, .vlan_del = ksz9477_port_vlan_del, + .drop_untagged = ksz9477_port_drop_untagged, .mirror_add = ksz9477_port_mirror_add, .mirror_del = ksz9477_port_mirror_del,.get_caps = ksz9477_get_caps,drivers/net/dsa/microchip/ksz_common.c +1
-0@@ -220,6 +222,7 @@ static const struct ksz_dev_ops lan937x_dev_ops = { .vlan_filtering = ksz9477_port_vlan_filtering, .vlan_add = ksz9477_port_vlan_add, .vlan_del = ksz9477_port_vlan_del, + .drop_untagged = ksz9477_port_drop_untagged, .mirror_add = ksz9477_port_mirror_add, .mirror_del = ksz9477_port_mirror_del,.get_caps = lan937x_phylink_get_caps,drivers/net/dsa/microchip/ksz_common.c static int ksz_enable_port(struct dsa_switch · line 1263
Quoted 7 lines
drivers/net/dsa/microchip/ksz_common.c +3
-0@@ -1254,6 +1257,9 @@ static int ksz_enable_port(struct dsa_switch *ds, int port, {struct ksz_device *dev = ds->priv; + dev->dev_ops->vlan_add (dev, port,KSZ_DEFAULT_VLAN , +BRIDGE_VLAN_INFO_UNTAGGED ); +How many times can this be executed before the VLAN add operation fails
due to the VLAN already being present on the port? I notice you're ignoring the return code. Wouldn't it be better to do this atport_setup()time instead?
Quoted 4 lines
(side note, the PVID for standalone mode can be added at
port_setuptime. The PVID to use for bridges in VLAN-unaware mode can be allocated
atport_bridge_jointime)
Ok. I will add in port_bridge_join function for bridge vlan_aware ports.
Quoted 20 lines
Quoted 9 lines
drivers/net/dsa/microchip/ksz_common.c +5
-0if (!dsa_is_user_port (ds, port))return 0 ; +static int ksz_commit_pvid (struct dsa_switch *ds,int port) +{ +struct dsa_port *dp =dsa_to_port (ds, port); +struct net_device *br =dsa_port_bridge_dev_get (dp); +struct ksz_device *dev = ds->priv;drivers/net/dsa/microchip/ksz_common.c void ksz_get_pvid(struct ksz_device *dev, int port, u16 *pvid) · line 1375
Quoted 10 lines
drivers/net/dsa/microchip/ksz_common.c +10
-0+u16 pvid =KSZ_DEFAULT_VLAN ; +bool drop_untagged = false; +struct ksz_port *p; + + p = &dev->ports[port]; + +if (br &&br_vlan_enabled (br)) { + pvid = p->bridge_pvid.vid; + drop_untagged = !p->bridge_pvid.valid; + }
Quoted 9 lines
This is better in the sense that it resolves the need for the
configure_vlan_while_not_filteringhack. But standalone and VLAN- unaware
bridge ports still share the same PVID. Even more so, standalone ports
have address learning enabled, which will poison the address database of
VLAN-unaware bridge ports (and of other standalone ports):
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Quoted 2 lines
Are you going to do further work in this area?
For now, I thought I can fix the issue for bridge vlan unaware port. I have few other patch series to be submitted like gPTP, tc commands. If standalone port fix also needed for your patch series I can work on it otherwise I can take up later stage.
Quoted 10 lines
Quoted 10 lines
drivers/net/dsa/microchip/ksz_common.c +5
-0+ +ksz_set_pvid (dev, port, pvid); + +if (dev->dev_ops->drop_untagged) + dev->dev_ops->drop_untagged(dev, port,
drop_untagged);drivers/net/dsa/microchip/ksz_common.c +3
-0+ +return 0 ; +}
Vladimir Oltean
maintainerRe: [Patch RFC net-next 4/4] net: dsa: microchip: use private pvid for bridge_vlan_unwaware
Quoted 23 lines · On Tue, Aug 02, 2022 at 02:40:09PM +0000, [email protected] wrote:
Quoted 13 lines · Vladimir Oltean
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 9 lines · Arun Ramadoss
drivers/net/dsa/microchip/ksz_common.c +0
-0@@ -161,6 +161,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .vlan_filtering = ksz8_port_vlan_filtering, .vlan_add = ksz8_port_vlan_add,Quoted 8 lines
drivers/net/dsa/microchip/ksz_common.c static const struct ksz_dev_ops ksz8_dev_ops = { · line 164
Quoted 2 lines
drivers/net/dsa/microchip/ksz_common.c +1
-0.vlan_del = ksz8_port_vlan_del, + .drop_untagged = ksz8_port_enable_pvid,You'll have to explain this one. What impact does PVID insertion on KSZ8 have upon dropping/not dropping untagged packets? This patch is saying that when untagged packets should be dropped, PVID insertion should be enabled, and when untagged packets should be accepted, PVID insertion should be disabled. How come?
Quoted 4 lines
Its my mistake. I referred KSZ87xx datasheet but I couldn't find the register for the dropping the untagged packet. If that is the case, shall I remove the dropping of untagged packet feature from the ksz8 switches?
You'll have to see how KSZ8 behaves when the ingress port is configured with a PVID (through REG_PORT_CTRL_VID) which isn't present in the VLAN table. If untagged packets are dropped, that's your "drop untagged" setting. Some other switches will not do this, and accept untagged packets even if the VLAN table doesn't contain an entry for the PVID (or doesn't have this port as a member of that VLAN), but have a separate knob for dropping untagged traffic.
Quoted 6 lines
Quoted 6 lines
This is better in the sense that it resolves the need for the
configure_vlan_while_not_filteringhack. But standalone and VLAN-unaware bridge ports still share the same PVID. Even more so, standalone ports have address learning enabled, which will poison the address database of VLAN-unaware bridge ports (and of other standalone ports):
Quoted 8 lines
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Quoted 2 lines
Are you going to do further work in this area?
For now, I thought I can fix the issue for bridge vlan unaware port. I have few other patch series to be submitted like gPTP, tc commands. If standalone port fix also needed for your patch series I can work on it otherwise I can take up later stage.
I think the most imperative thing for you to do is to make sure you are not introducing regressions with the port default VID change - this can be done by running the bridge related selftests (and making them pass).
Something which I forgot to mention is that normally, I'd expect a change of VLAN-unaware PVID to also need a change in the way that VLAN-unaware FDB entries are added (other drivers need to remap vid=0 from port_fdb_add() to the PVID that they use for that VLAN-unaware bridge, in your case 4095, for those FDB entries to continue matching properly).
However, I see that currently, ksz9477_fdb_add() sets the "USE FID" bit only for VLAN-aware FDB entries (vid != 0), which leaves me with more questions than answers.
It isn't very well explained what it means to not use FID: let's say there are 2 entries in the static address table, one has "USE FID"=false, and the other has "USE FID"=true and FID=127, and a packet is received which is classified to FID 127. On which entry will this packet match?
The bridge driver gives you all FDB entries at once (VLAN-aware and VLAN-unaware), so if the USE_FID=false entries that the ksz9477 driver uses for VLAN-unaware mode will shadow the VLAN-aware FDB entries, this is going to be a problem.
Also, the way in which the ksz9477 driver translates a 12-bit VID into a 7-bit FID also has me incredibly confused (FID is vlan->vid & VLAN_FID_M, or otherwise said, a simple truncation). This means that your VLAN-unaware PVID of 4095 uses a FID of 127, which is also the same FID as VLANs 127, 255, 383 etc, right? So there is potentially still full address database leakage between VLAN-unaware and VLAN-aware bridges.
I think this phrase from the documentation is under-appreciated in understanding how the hardware works:
| Table 4-8 details the forwarding and discarding actions that are taken | for the various VLAN scenarios. The first entry in the table is | explained by the fact that VLAN Table lookup is enabled even when 802.1Q | VLAN is not enabled.
The last part ("VLAN Table lookup is enabled even when 802.1Q VLAN is not enabled") is what makes it so that the PVID of the port must be present in the VLAN table or otherwise you get packet drops. In turn, if the VLAN table is being looked up, it means that regardless of whether the switch is VLAN-unaware or not, the VID will be transformed into a 7-bit FID.
I want that the FID that is being used for standalone ports and VLAN-unaware bridges (127) to be a fully conscious decision, with the implications understood, and not just something done for me to shut up. There is a risk here that you may think things are fine and work on other features, but things are not fine at all. And in this area, standalone ports/bridge VLANs/ FDB entries/FIDs are very inter-related things. When you change one, you may find that the entire scheme needs to be re-thought.