FogBugz #516535: Fix QSPI write issues
PATCH 16/347 FogBugz #516535: Fix QSPI write issues
From: Chee Hong Ang <[email protected]>
QSPI driver perform chip select on every flash read/write access. The driver need to disable/enable the QSPI controller while performing chip select. This may cause some data lost especially the QSPI controller is configured to run at slower speed as it may take longer time to access the flash device. This patch prevent the driver from disable/enable the QSPI controller too soon and inadvertently halting any ongoing flash read/write access by ensuring the QSPI controller is always in idle mode after each read/write access.
--- drivers/spi/cadence_qspi_apb.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)
drivers/spi/cadence_qspi_apb.c +8 -7
@@ -858,13 +858,9 @@ cadence_qspi_apb_indirect_read_execute(struct cadence_spi_plat *plat,writel (CQSPI_REG_INDIRECTRD_DONE , plat->regbase +CQSPI_REG_INDIRECTRD ); -/* Check indirect done status */ - ret =wait_for_bit_le32 (plat->regbase +CQSPI_REG_INDIRECTRD , -CQSPI_REG_INDIRECTRD_DONE ,0 ,10 ,0 ); -if (ret) { -printf ("Indirect read clear completion error (%i)\n" , ret); - goto failrd; - } +/* Wait til QSPI is idle */ +if (!cadence_qspi_wait_idle (plat->regbase)) +return -EIO ;return 0 ;
@@ -1031,6 +1027,11 @@ cadence_qspi_apb_indirect_write_execute(struct cadence_spi_plat *plat,if (bounce_buf)free (bounce_buf); + +/* Wait til QSPI is idle */ +if (!cadence_qspi_wait_idle (plat->regbase)) +return -EIO ; +return 0 ; failwr:
Signature · 1 line
2.25.1
Hi Jit Loon,
Quoted 9 lines
-----Original Message-----
From: Lim, Jit Loon <[email protected]>
Sent: Tuesday, 2 August, 2022 9:55 PM
To: [email protected]
Cc: Jagan Teki <[email protected]>; Vignesh R <[email protected]>; Vasut, Marek <[email protected]>; Simon <[email protected]>; Chaplin, Kris <[email protected]>; Chee, Tien Fong <[email protected]>; Hea, Kok Kiang <[email protected]>; Lim, Elly Siew Chin <[email protected]>; Kho, Sin Hui
Quoted 8 lines
<[email protected]>; Lokanathan, Raaj <[email protected]>; Maniyam, Dinesh <[email protected]>; Ng, Boon Khai <[email protected]>; Yuslaimi, Alif Zakuan <[email protected]>; Chong, Teik Heng <[email protected]>; Zamri, Muhammad Hazim Izzat <[email protected]>; Lim, Jit Loon <[email protected]>; Chee Hong Ang <[email protected]>
Subject: [PATCH 016/347] FogBugz #516535: Fix QSPI write issues
Please drop the "[PATCH 016/347]" and replace "FogBugz #516535" with appropriate tag.
Quoted 50 lines
From: Chee Hong Ang <[email protected]>
QSPI driver perform chip select on every flash read/write access. The driver need to disable/enable the QSPI controller while performing chip select. This may cause some data lost especially the QSPI controller is configured to run at slower speed as it may take longer time to access the flash device. This patch prevent the driver from disable/enable the QSPI controller too soon and inadvertently halting any ongoing flash read/write access by ensuring the QSPI controller is always in idle mode after each read/write access.
Signed-off-by Chee Hong Ang <[email protected]>--- drivers/spi/cadence_qspi_apb.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)drivers/spi/cadence_qspi_apb.c +8
-7@@ -858,13 +858,9 @@ cadence_qspi_apb_indirect_read_execute(struct cadence_spi_plat *plat,writel (CQSPI_REG_INDIRECTRD_DONE , plat->regbase +CQSPI_REG_INDIRECTRD ); -/* Check indirect done status */ - ret =wait_for_bit_le32 (plat->regbase +CQSPI_REG_INDIRECTRD , -CQSPI_REG_INDIRECTRD_DONE ,0 ,10 ,0 ); -if (ret) { -printf ("Indirect read clear completion error (%i)\n" , ret); - goto failrd; - } +/* Wait til QSPI is idle */ +if (!cadence_qspi_wait_idle (plat->regbase)) +return -EIO ;return 0 ;@@ -1031,6 +1027,11 @@ cadence_qspi_apb_indirect_write_execute(struct cadence_spi_plat *plat, if (bounce_buf) free(bounce_buf); + +/* Wait til QSPI is idle */ +if (!cadence_qspi_wait_idle (plat->regbase)) +return -EIO ; +return 0 ;
Quoted 3 lines
failwr:
--
2.25.1
Regards,
Tien Fong