arm: mvebu: turris_mox: Set "sfp" label in eth1 DT node when only Mox SFP is detected
PATCH 1/1 arm: mvebu: turris_mox: Set "sfp" label in eth1 DT node when only Mox SFP is detected
When Mox SFP module is connected after Topaz or Peridot module then port DT node already contains "sfp" label. But Mox SFP module can be connected also without Topaz or Peridot module in which case it is connected directly into he eth1 DT node, which is without any label. So add "sfp" label into eth1 DT node in this case.
--- board/CZ.NIC/turris_mox/turris_mox.c | 5 +++++ 1 file changed, 5 insertions(+)
board/CZ.NIC/turris_mox/turris_mox.c +5 -0
@@ -821,6 +821,11 @@ int ft_board_setup(void *blob, struct bd_info *bd) "sgmii");if (res <0 )return res; + + res =fdt_setprop_string (blob, node,"label" , +"sfp" ); +if (res <0 ) +return res; } res =fdt_status_okay_by_compatible (blob,"cznic,moxtet-gpio" );
Signature · 1 line
2.20.1
Quoted 7 lines · On Wed, 10 Aug 2022 12:54:11 +0200 Pali Rohár <[email protected]> wrote:
When Mox SFP module is connected after Topaz or Peridot module then port DT node already contains "sfp" label. But Mox SFP module can be connected also without Topaz or Peridot module in which case it is connected directly into he eth1 DT node, which is without any label. So add "sfp" label into eth1 DT node in this case.
Signed-off-by Pali Rohár <[email protected]>
Quoted 7 lines · Pali Rohár
When Mox SFP module is connected after Topaz or Peridot module then port DT node already contains "sfp" label. But Mox SFP module can be connected also without Topaz or Peridot module in which case it is connected directly into he eth1 DT node, which is without any label. So add "sfp" label into eth1 DT node in this case.
Signed-off-by Pali Rohár <[email protected]>
Thanks,
Stefan
Quoted 10 lines
--- board/CZ.NIC/turris_mox/turris_mox.c | 5 +++++ 1 file changed, 5 insertions(+)board/CZ.NIC/turris_mox/turris_mox.c +0
-0@@ -821,6 +821,11 @@ int ft_board_setup(void *blob, struct bd_info *bd) "sgmii");
board/CZ.NIC/turris_mox/turris_mox.c int ft_board_setup(void *blob, struct bd_info *bd) · line 831
Quoted 10 lines
board/CZ.NIC/turris_mox/turris_mox.c +5
-0if (res <0 )return res; + + res =fdt_setprop_string (blob, node,"label" , +"sfp" ); +if (res <0 ) +return res; } res =fdt_status_okay_by_compatible (blob,"cznic,moxtet-gpio" );
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 7 lines · Pali Rohár
When Mox SFP module is connected after Topaz or Peridot module then port DT node already contains "sfp" label. But Mox SFP module can be connected also without Topaz or Peridot module in which case it is connected directly into he eth1 DT node, which is without any label. So add "sfp" label into eth1 DT node in this case.
Signed-off-by Pali Rohár <[email protected]>
Applied to u-boot-marvell/master
Thanks,
Stefan
Quoted 10 lines
--- board/CZ.NIC/turris_mox/turris_mox.c | 5 +++++ 1 file changed, 5 insertions(+)board/CZ.NIC/turris_mox/turris_mox.c +0
-0@@ -821,6 +821,11 @@ int ft_board_setup(void *blob, struct bd_info *bd) "sgmii");
board/CZ.NIC/turris_mox/turris_mox.c int ft_board_setup(void *blob, struct bd_info *bd) · line 831
Quoted 10 lines
board/CZ.NIC/turris_mox/turris_mox.c +5
-0if (res <0 )return res; + + res =fdt_setprop_string (blob, node,"label" , +"sfp" ); +if (res <0 ) +return res; } res =fdt_status_okay_by_compatible (blob,"cznic,moxtet-gpio" );
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]