PolarFire SoC reset controller & clock cleanups
Subsystems (5)
Conor Dooley
maintainerv3 cover PolarFire SoC reset controller & clock cleanups
Hey all,
Kinda two things happening in this series, but I sent it together to ensure the second part would apply correctly.
The first is the reset controller that I promised after discovering the issue triggered by CONFIG_PM & the phy not coming up correctly. I have now removed all the messing with resets from clock enable/disable functions & now use the aux bus to set up a reset controller driver. Since I needed something to test it, I hooked up the reset for the Cadence MACB on PolarFire SoC. This was been split into a second series for v2 (and is now in v6.0-rcN):
https://lore.kernel.org/all/[email protected]/
The second part adds rate control for the MSS PLL clock, followed by some simplifications to the driver & conversions of some custom structs to the corresponding structs in the framework.
I'll take the dts patch myself when the rest of this is accepted. Thanks,
Conor.
Changes since v2:
- reorder reset Makefile/Kconfig entries
- fix a pre-existing bug exposed by clang with this series applied
- add Padmarao who co-authored the original driver to the authors
Conor Dooley (13):
clk: microchip: mpfs: fix clk_cfg array bounds violation
dt-bindings: clk: microchip: mpfs: add reset controller support
clk: microchip: mpfs: add reset controller
reset: add polarfire soc reset support
MAINTAINERS: add polarfire soc reset controller
riscv: dts: microchip: add mpfs specific macb reset support
clk: microchip: mpfs: add MSS pll's set & round rate
clk: microchip: mpfs: move id & offset out of clock structs
clk: microchip: mpfs: simplify control reg access
clk: microchip: mpfs: delete 2 line mpfs_clk_register_foo()
clk: microchip: mpfs: convert cfg_clk to clk_divider
clk: microchip: mpfs: convert periph_clk to clk_gate
clk: microchip: mpfs: update module authorship & licencing
.../bindings/clock/microchip,mpfs.yaml | 17 +- MAINTAINERS | 1 + arch/riscv/boot/dts/microchip/mpfs.dtsi | 7 +- drivers/clk/microchip/Kconfig | 1 + drivers/clk/microchip/clk-mpfs.c | 386 +++++++++--------- drivers/reset/Kconfig | 7 + drivers/reset/Makefile | 2 +- drivers/reset/reset-mpfs.c | 157 +++++++ include/soc/microchip/mpfs.h | 8 + 9 files changed, 391 insertions(+), 195 deletions(-) create mode 100644 drivers/reset/reset-mpfs.c
base-commit: 568035b01cfb107af8d2e4bd2fb9aea22cf5b868
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 1/13 clk: microchip: mpfs: fix clk_cfg array bounds violation
Unnoticed in current code, there is an array bounds violation present during clock registration. This seems to fail gracefully in v6.0-rc1, and life carrys on. While converting the driver to use standard clock structs/ops, kernel panics were seen during boot when built with clang:
[ 0.581754] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000b1 [ 0.591520] Oops [#1] [ 0.594045] Modules linked in: [ 0.597435] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.0.0-rc1-00011-g8e1459cf4eca #1 [ 0.606188] Hardware name: Microchip PolarFire-SoC Icicle Kit (DT) [ 0.613012] epc : __clk_register+0x4a6/0x85c [ 0.617759] ra : __clk_register+0x49e/0x85c [ 0.622489] epc : ffffffff803faf7c ra : ffffffff803faf74 sp : ffffffc80400b720 [ 0.630466] gp : ffffffff810e93f8 tp : ffffffe77fe60000 t0 : ffffffe77ffb3800 [ 0.638443] t1 : 000000000000000a t2 : ffffffffffffffff s0 : ffffffc80400b7c0 [ 0.646420] s1 : 0000000000000001 a0 : 0000000000000001 a1 : 0000000000000000 [ 0.654396] a2 : 0000000000000001 a3 : 0000000000000000 a4 : 0000000000000000 [ 0.662373] a5 : ffffffff803a5810 a6 : 0000000200000022 a7 : 0000000000000006 [ 0.670350] s2 : ffffffff81099d48 s3 : ffffffff80d6e28e s4 : 0000000000000028 [ 0.678327] s5 : ffffffff810ed3c8 s6 : ffffffff810ed3d0 s7 : ffffffe77ffbc100 [ 0.686304] s8 : ffffffe77ffb1540 s9 : ffffffe77ffb1540 s10: 0000000000000008 [ 0.694281] s11: 0000000000000000 t3 : 00000000000000c6 t4 : 0000000000000007 [ 0.702258] t5 : ffffffff810c78c0 t6 : ffffffe77ff88cd0 [ 0.708125] status: 0000000200000120 badaddr: 00000000000000b1 cause: 000000000000000d [ 0.716869] [<ffffffff803fb892>] devm_clk_hw_register+0x62/0xaa [ 0.723420] [<ffffffff80403412>] mpfs_clk_probe+0x1e0/0x244
It fails on "clk_periph_timer" - which uses a different parent, that it tries to find using the macro:
\#define PARENT_CLK(PARENT) (&mpfs_cfg_clks[CLK_##PARENT].cfg.hw)
If parent is RTCREF, so the macro becomes: &mpfs_cfg_clks[33].cfg.hw which is well beyond the end of the array. Amazingly, builds with GCC 11.1 see no problem here, booting correctly and hooking the parent up etc. Builds with clang-15 do not, with the above panic.
Drop the macro for the RTCREF and use the array directly to avoid the panic, using a newly added define that brings the index into the valid range.
--- drivers/clk/microchip/clk-mpfs.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/clk/microchip/clk-mpfs.c +4 -1
@@ -27,6 +27,8 @@#define MSSPLL_POSTDIV_WIDTH 0x07u#define MSSPLL_FIXED_DIV 4u +#define RTCREF_OFFSET (CLK_RTCREF - CLK_ENVM) +struct mpfs_clock_data {void __iomem *base;void __iomem *msspll_base;
@@ -381,7 +383,8 @@ static struct mpfs_periph_hw_clock mpfs_periph_clks[] = {CLK_PERIPH (CLK_MAC0 ,"clk_periph_mac0" ,PARENT_CLK (AHB ),1 ,0 ),CLK_PERIPH (CLK_MAC1 ,"clk_periph_mac1" ,PARENT_CLK (AHB ),2 ,0 ),CLK_PERIPH (CLK_MMC ,"clk_periph_mmc" ,PARENT_CLK (AHB ),3 ,0 ), -CLK_PERIPH (CLK_TIMER ,"clk_periph_timer" ,PARENT_CLK (RTCREF ),4 ,0 ), +CLK_PERIPH (CLK_TIMER ,"clk_periph_timer" , + &mpfs_cfg_clks[CLK_RTCREF -RTCREF_OFFSET ].hw,4 ,0 ),CLK_PERIPH (CLK_MMUART0 ,"clk_periph_mmuart0" ,PARENT_CLK (AHB ),5 ,CLK_IS_CRITICAL ),CLK_PERIPH (CLK_MMUART1 ,"clk_periph_mmuart1" ,PARENT_CLK (AHB ),6 ,0 ), CLK_PERIPH(CLK_MMUART2, "clk_periph_mmuart2", PARENT_CLK(AHB), 7, 0),
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 2/13 dt-bindings: clk: microchip: mpfs: add reset controller support
In reply to Conor DooleyThe "peripheral" devices on PolarFire SoC can be put into reset, so update the device tree binding to reflect the presence of a reset controller.
--- .../bindings/clock/microchip,mpfs.yaml | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/clock/microchip,mpfs.yaml +15 -2
@@ -40,8 +40,21 @@ properties: const: 1 description: | The clock consumer should specify the desired clock by having the clock - ID in its "clocks" phandle cell. See include/dt-bindings/clock/microchip,mpfs-clock.h - for the full list of PolarFire clock IDs. + ID in its "clocks" phandle cell. + See include/dt-bindings/clock/microchip,mpfs-clock.h for the full list of + PolarFire clock IDs. + + resets: + maxItems: 1 + + '#reset-cells': + description: + The AHB/AXI peripherals on the PolarFire SoC have reset support, so from + CLK_ENVM to CLK_CFM. The reset consumer should specify the desired + peripheral via the clock ID in its "resets" phandle cell. + See include/dt-bindings/clock/microchip,mpfs-clock.h for the full list of + PolarFire clock IDs. + const: 1 required: - compatible
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 3/13 clk: microchip: mpfs: add reset controller
In reply to Conor DooleyAdd a reset controller to PolarFire SoC's clock driver. This reset controller is registered as an aux device and read/write functions exported to the drivers namespace so that the reset controller can access the peripheral device reset register.
--- drivers/clk/microchip/Kconfig | 1 + drivers/clk/microchip/clk-mpfs.c | 116 ++++++++++++++++++++++++++++--- include/soc/microchip/mpfs.h | 8 +++ 3 files changed, 114 insertions(+), 11 deletions(-)
drivers/clk/microchip/Kconfig +1 -0
@@ -6,5 +6,6 @@ config COMMON_CLK_PIC32 config MCHP_CLK_MPFS bool "Clk driver for PolarFire SoC" depends on (RISCV && SOC_MICROCHIP_POLARFIRE) || COMPILE_TEST + select AUXILIARY_BUS help Supports Clock Configuration for PolarFire SoC
drivers/clk/microchip/clk-mpfs.c +105 -11
170 lines not on this page · raw message
include/soc/microchip/mpfs.h +8 -0
@@ -40,4 +40,12 @@ struct mpfs_sys_controller *mpfs_sys_controller_get(struct device *dev);#endif /* if IS_ENABLED(CONFIG_POLARFIRE_SOC_SYS_CTRL) */ +#if IS_ENABLED (CONFIG_MCHP_CLK_MPFS ) + +u32 mpfs_reset_read (struct device *dev); + +void mpfs_reset_write (struct device *dev,u32 val); + +#endif /* if IS_ENABLED(CONFIG_MCHP_CLK_MPFS) */ +#endif /* __SOC_MPFS_H__ */
Signature · 1 line
2.36.1
Re: [PATCH v3 03/13] clk: microchip: mpfs: add reset controller
Quoted 155 lines · Conor Dooley
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Add a reset controller to PolarFire SoC's clock driver. This reset controller is registered as an aux device and read/write functions exported to the drivers namespace so that the reset controller can access the peripheral device reset register.
Reviewed-by Daire McNamara <[email protected]>Signed-off-by Conor Dooley <[email protected]>--- drivers/clk/microchip/Kconfig | 1 + drivers/clk/microchip/clk-mpfs.c | 116 ++++++++++++++++++++++++++++--- include/soc/microchip/mpfs.h | 8 +++ 3 files changed, 114 insertions(+), 11 deletions(-)drivers/clk/microchip/Kconfig +1
-0@@ -6,5 +6,6 @@ config COMMON_CLK_PIC32 config MCHP_CLK_MPFS bool "Clk driver for PolarFire SoC" depends on (RISCV && SOC_MICROCHIP_POLARFIRE) || COMPILE_TEST + select AUXILIARY_BUS help Supports Clock Configuration for PolarFire SoCdrivers/clk/microchip/clk-mpfs.c +77
-10@@ -3,12 +3,14 @@* Daire McNamara,<[email protected]> * Copyright (C) 2020 Microchip Technology Inc. All rights reserved. */ +#include <linux/auxiliary_bus.h> #include <linux/clk-provider.h> #include <linux/io.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <dt-bindings/clock/microchip,mpfs-clock.h> +#include <soc/microchip/mpfs.h> /* address offset of control registers */ #define REG_MSSPLL_REF_CR 0x08u@@ -30,6 +32,7 @@#define RTCREF_OFFSET (CLK_RTCREF - CLK_ENVM)struct mpfs_clock_data { +struct device *dev;void __iomem *base;void __iomem *msspll_base;struct clk_hw_onecell_data hw_data;@@ -304,10 +307,6 @@ static int mpfs_periph_clk_enable(struct clk_hw *hw)spin_lock_irqsave (&mpfs_clk_lock, flags); - reg =readl_relaxed (base_addr +REG_SUBBLK_RESET_CR ); - val = reg & ~(1u << periph->shift); -writel_relaxed (val, base_addr +REG_SUBBLK_RESET_CR ); - reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); val = reg | (1u << periph->shift);writel_relaxed (val, base_addr +REG_SUBBLK_CLOCK_CR );@@ -341,12 +340,9 @@ static int mpfs_periph_clk_is_enabled(struct clk_hw *hw)void __iomem *base_addr = periph_hw->sys_base;u32 reg; - reg =readl_relaxed (base_addr +REG_SUBBLK_RESET_CR ); -if ((reg & (1u << periph->shift)) ==0u ) { - reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); -if (reg & (1u << periph->shift)) -return 1 ; - } + reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); +if (reg & (1u << periph->shift)) +return 1 ;return 0 ; }@@ -441,6 +437,98 @@ static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_creturn 0 ; } +/* +* Peripheral clock resets +*/ + +#if IS_ENABLED (CONFIG_RESET_CONTROLLER ) + +u32 mpfs_reset_read (struct device *dev) +{ +struct mpfs_clock_data *clock_data =dev_get_drvdata (dev->parent); + +return readl_relaxed (clock_data->base +REG_SUBBLK_RESET_CR ); +} +EXPORT_SYMBOL_NS_GPL (mpfs_reset_read,MCHP_CLK_MPFS ); + +void mpfs_reset_write (struct device *dev,u32 val) +{ +struct mpfs_clock_data *clock_data =dev_get_drvdata (dev->parent); + +writel_relaxed (val, clock_data->base +REG_SUBBLK_RESET_CR ); +} +EXPORT_SYMBOL_NS_GPL (mpfs_reset_write,MCHP_CLK_MPFS ); + +static void mpfs_reset_unregister_adev (void *_adev) +{ +struct auxiliary_device *adev = _adev; + +auxiliary_device_delete (adev); +} + +static void mpfs_reset_adev_release (struct device *dev) +{ +struct auxiliary_device *adev =to_auxiliary_dev (dev); + +auxiliary_device_uninit (adev); + +kfree (adev); +} + +static struct auxiliary_device *mpfs_reset_adev_alloc (struct mpfs_clock_data *clk_data) +{ +struct auxiliary_device *adev; +int ret; + + adev =kzalloc (sizeof (*adev),GFP_KERNEL ); +if (!adev) +return ERR_PTR (-ENOMEM ); + + adev->name ="reset-mpfs" ; + adev->dev.parent = clk_data->dev; + adev->dev.release = mpfs_reset_adev_release; + adev->id =666u ; + + ret =auxiliary_device_init (adev); +if (ret) { +kfree (adev); +return ERR_PTR (ret); + } + +return adev; +} + +static int mpfs_reset_controller_register (struct mpfs_clock_data *clk_data) +{ +struct auxiliary_device *adev; +int ret; + + adev =mpfs_reset_adev_alloc (clk_data); +if (IS_ERR (adev)) +return PTR_ERR (adev); + + ret =auxiliary_device_add (adev);
drivers/clk/microchip/clk-mpfs.c static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_c · line 520
Quoted 10 lines
drivers/clk/microchip/clk-mpfs.c +10
-0+if (ret) { +auxiliary_device_uninit (adev); +return ret; + } + + ret =devm_add_action_or_reset (clk_data->dev, mpfs_reset_unregister_adev, adev); +if (ret) +return ret; + +return 0 ;
You can just:
return ret; or: return devm_add_action_or_reset();
Quoted 24 lines
drivers/clk/microchip/clk-mpfs.c +13
-0+} + +#else /* !CONFIG_RESET_CONTROLLER */ + +static int mpfs_reset_controller_register (struct mpfs_clock_data *clk_data) +{ +return 0 ; +} + +#endif /* !CONFIG_RESET_CONTROLLER */ +static int mpfs_clk_probe (struct platform_device *pdev) {struct device *dev = &pdev->dev;@@ -465,6 +553,8 @@ static int mpfs_clk_probe(struct platform_device *pdev)return PTR_ERR (clk_data->msspll_base); clk_data->hw_data.num = num_clks; + clk_data->dev = dev; +dev_set_drvdata (dev, clk_data); ret =mpfs_clk_register_mssplls (dev, mpfs_msspll_clks,ARRAY_SIZE (mpfs_msspll_clks), clk_data);
drivers/clk/microchip/clk-mpfs.c static int mpfs_clk_probe(struct platform_device *pdev) · line 581
Quoted 8 lines
drivers/clk/microchip/clk-mpfs.c +4
-0@@ -484,6 +574,10 @@ static int mpfs_clk_probe(struct platform_device *pdev)if (ret)return ret; + ret =mpfs_reset_controller_register (clk_data); +if (ret) +return ret; +return ret;
Ditto
Quoted 31 lines
drivers/clk/microchip/clk-mpfs.c +1
-1}@@ -491,7 +585,7 @@ static const struct of_device_id mpfs_clk_of_match_table[] = { { .compatible = "microchip,mpfs-clkcfg", }, {} }; -MODULE_DEVICE_TABLE (of, mpfs_clk_match_table); +MODULE_DEVICE_TABLE (of, mpfs_clk_of_match_table);static struct platform_driver mpfs_clk_driver = { .probe = mpfs_clk_probe,include/soc/microchip/mpfs.h +8
-1@@ -40,4 +40,12 @@ struct mpfs_sys_controller *mpfs_sys_controller_get(struct device *dev);#endif /* if IS_ENABLED(CONFIG_POLARFIRE_SOC_SYS_CTRL) */ +#if IS_ENABLED (CONFIG_MCHP_CLK_MPFS ) + +u32 mpfs_reset_read (struct device *dev); + +void mpfs_reset_write (struct device *dev,u32 val); + +#endif /* if IS_ENABLED(CONFIG_MCHP_CLK_MPFS) */ +#endif /* __SOC_MPFS_H__ */ --2.36.1
[email protected]
maintainerRe: [PATCH v3 03/13] clk: microchip: mpfs: add reset controller
Quoted 65 lines · On 30/08/2022 07:40, Claudiu Beznea - M18063 wrote:
Quoted 21 lines · Conor Dooley
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Add a reset controller to PolarFire SoC's clock driver. This reset controller is registered as an aux device and read/write functions exported to the drivers namespace so that the reset controller can access the peripheral device reset register.
Reviewed-by Daire McNamara <[email protected]>Signed-off-by Conor Dooley <[email protected]>---
drivers/clk/microchip/clk-mpfs.c +10
-0+static int mpfs_reset_controller_register (struct mpfs_clock_data *clk_data) +{ +struct auxiliary_device *adev; +int ret; + + adev =mpfs_reset_adev_alloc (clk_data); +if (IS_ERR (adev)) +return PTR_ERR (adev); + + ret =auxiliary_device_add (adev);drivers/clk/microchip/clk-mpfs.c static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_c · line 520
Quoted 10 lines
drivers/clk/microchip/clk-mpfs.c +10
-0+if (ret) { +auxiliary_device_uninit (adev); +return ret; + } + + ret =devm_add_action_or_reset (clk_data->dev, mpfs_reset_unregister_adev, adev); +if (ret) +return ret; + +return 0 ;You can just:
return ret; or: return devm_add_action_or_reset();Quoted 27 lines
drivers/clk/microchip/clk-mpfs.c +13
-0+} + +#else /* !CONFIG_RESET_CONTROLLER */ + +static int mpfs_reset_controller_register (struct mpfs_clock_data *clk_data) +{ +return 0 ; +} + +#endif /* !CONFIG_RESET_CONTROLLER */ +static int mpfs_clk_probe (struct platform_device *pdev) {struct device *dev = &pdev->dev;@@ -465,6 +553,8 @@ static int mpfs_clk_probe(struct platform_device *pdev)return PTR_ERR (clk_data->msspll_base); clk_data->hw_data.num = num_clks; + clk_data->dev = dev; +dev_set_drvdata (dev, clk_data); ret =mpfs_clk_register_mssplls (dev, mpfs_msspll_clks,ARRAY_SIZE (mpfs_msspll_clks), clk_data);@@ -484,6 +574,10 @@ static int mpfs_clk_probe(struct platform_device *pdev)if (ret)return ret;
Quoted 10 lines
drivers/clk/microchip/clk-mpfs.c static int mpfs_clk_probe(struct platform_device *pdev) · line 581
Quoted 5 lines
drivers/clk/microchip/clk-mpfs.c +4
-0+ ret =mpfs_reset_controller_register (clk_data); +if (ret) +return ret; +return ret;Ditto
Quoted 2 lines
(quoted diff) +0
-0}
willdo^2
Thanks,
Conor.
Conor Dooley
maintainerPATCH v3 4/13 reset: add polarfire soc reset support
In reply to Conor DooleyAdd support for the resets on Microchip's PolarFire SoC (MPFS). Reset control is a single register, wedged in between registers for clock control. To fit with existed DT etc, the reset controller is created using the aux device framework & set up in the clock driver.
--- drivers/reset/Kconfig | 7 ++ drivers/reset/Makefile | 2 +- drivers/reset/reset-mpfs.c | 157 +++++++++++++++++++++++++++++++++++++ 3 files changed, 165 insertions(+), 1 deletion(-) create mode 100644 drivers/reset/reset-mpfs.c
drivers/reset/Kconfig +7 -0
@@ -152,6 +152,13 @@ config RESET_PISTACHIO help This enables the reset driver for ImgTec Pistachio SoCs. +config RESET_POLARFIRE_SOC + bool "Microchip PolarFire SoC (MPFS) Reset Driver" + depends on AUXILIARY_BUS && MCHP_CLK_MPFS + default MCHP_CLK_MPFS + help + This driver supports peripheral reset for the Microchip PolarFire SoC + config RESET_QCOM_AOSS tristate "Qcom AOSS Reset Driver" depends on ARCH_QCOM || COMPILE_TEST
drivers/reset/Makefile +1 -1
@@ -22,6 +22,7 @@ obj-$(CONFIG_RESET_MESON_AUDIO_ARB) += reset-meson-audio-arb.o obj-$(CONFIG_RESET_NPCM) += reset-npcm.o obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o obj-$(CONFIG_RESET_PISTACHIO) += reset-pistachio.o +obj-$(CONFIG_RESET_POLARFIRE_SOC) += reset-mpfs.o obj-$(CONFIG_RESET_QCOM_AOSS) += reset-qcom-aoss.o obj-$(CONFIG_RESET_QCOM_PDC) += reset-qcom-pdc.o obj-$(CONFIG_RESET_RASPBERRYPI) += reset-raspberrypi.o
@@ -40,4 +41,3 @@ obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o obj-$(CONFIG_RESET_UNIPHIER_GLUE) += reset-uniphier-glue.o obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o -
drivers/reset/reset-mpfs.c new file +157 -0
157 lines not on this page · raw message
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 5/13 MAINTAINERS: add polarfire soc reset controller
In reply to Conor DooleyAdd the newly added reset controller for the PolarFire SoC (MPFS) to the existing MAINTAINERS entry.
--- MAINTAINERS | 1 + 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
@@ -17532,6 +17532,7 @@ F: drivers/char/hw_random/mpfs-rng.c F: drivers/clk/microchip/clk-mpfs.c F: drivers/mailbox/mailbox-mpfs.c F: drivers/pci/controller/pcie-microchip-host.c +F: drivers/reset/reset-mpfs.c F: drivers/rtc/rtc-mpfs.c F: drivers/soc/microchip/ F: drivers/spi/spi-microchip-core.c
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 6/13 riscv: dts: microchip: add mpfs specific macb reset support
In reply to Conor DooleyThe macb on PolarFire SoC has reset support which the generic compatible does not use. Add the newly introduced MPFS specific compatible as the primary compatible to avail of this support & wire up the reset to the clock controllers devicetree entry.
--- arch/riscv/boot/dts/microchip/mpfs.dtsi | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
arch/riscv/boot/dts/microchip/mpfs.dtsi +5 -2
@@ -234,6 +234,7 @@ clkcfg: clkcfg@20002000 { reg = <0x0 0x20002000 0x0 0x1000>, <0x0 0x3E001000 0x0 0x1000>; clocks = <&refclk>; #clock-cells = <1>; + #reset-cells = <1>; }; mmuart0: serial@20000000 {
@@ -383,7 +384,7 @@ can1: can@2010d000 { }; mac0: ethernet@20110000 { - compatible = "cdns,macb"; + compatible = "microchip,mpfs-macb", "cdns,macb"; reg = <0x0 0x20110000 0x0 0x2000>; #address-cells = <1>; #size-cells = <0>;
@@ -392,11 +393,12 @@ mac0: ethernet@20110000 { local-mac-address = [00 00 00 00 00 00]; clocks = <&clkcfg CLK_MAC0>, <&clkcfg CLK_AHB>; clock-names = "pclk", "hclk"; + resets = <&clkcfg CLK_MAC0>; status = "disabled"; }; mac1: ethernet@20112000 { - compatible = "cdns,macb"; + compatible = "microchip,mpfs-macb", "cdns,macb"; reg = <0x0 0x20112000 0x0 0x2000>; #address-cells = <1>; #size-cells = <0>;
@@ -405,6 +407,7 @@ mac1: ethernet@20112000 { local-mac-address = [00 00 00 00 00 00]; clocks = <&clkcfg CLK_MAC1>, <&clkcfg CLK_AHB>; clock-names = "pclk", "hclk"; + resets = <&clkcfg CLK_MAC1>; status = "disabled"; };
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 7/13 clk: microchip: mpfs: add MSS pll's set & round rate
In reply to Conor DooleyThe MSS pll is not a fixed frequency clock, so add set() & round_rate() support.
Control is limited to a 7 bit output divider as other devices on the FPGA occupy the other three outputs of the PLL & prevent changing the multiplier.
--- drivers/clk/microchip/clk-mpfs.c | 54 ++++++++++++++++++++++++++++++++ 1 file changed, 54 insertions(+)
drivers/clk/microchip/clk-mpfs.c +54 -0
@@ -131,8 +131,62 @@ static unsigned long mpfs_clk_msspll_recalc_rate(struct clk_hw *hw, unsigned lonreturn prate * mult / (ref_div *MSSPLL_FIXED_DIV * postdiv); } +static long mpfs_clk_msspll_round_rate (struct clk_hw *hw,unsigned long rate,unsigned long *prate) +{ +struct mpfs_msspll_hw_clock *msspll_hw =to_mpfs_msspll_clk (hw); +void __iomem *mult_addr = msspll_hw->base + msspll_hw->reg_offset; +void __iomem *ref_div_addr = msspll_hw->base +REG_MSSPLL_REF_CR ; +u32 mult, ref_div; +unsigned long rate_before_ctrl; + + mult =readl_relaxed (mult_addr) >>MSSPLL_FBDIV_SHIFT ; + mult &=clk_div_mask (MSSPLL_FBDIV_WIDTH ); + ref_div =readl_relaxed (ref_div_addr) >>MSSPLL_REFDIV_SHIFT ; + ref_div &=clk_div_mask (MSSPLL_REFDIV_WIDTH ); + + rate_before_ctrl = rate * (ref_div *MSSPLL_FIXED_DIV ) / mult; + +return divider_round_rate (hw, rate_before_ctrl, prate,NULL ,MSSPLL_POSTDIV_WIDTH , + msspll_hw->flags); +} + +static int mpfs_clk_msspll_set_rate (struct clk_hw *hw,unsigned long rate,unsigned long prate) +{ +struct mpfs_msspll_hw_clock *msspll_hw =to_mpfs_msspll_clk (hw); +void __iomem *mult_addr = msspll_hw->base + msspll_hw->reg_offset; +void __iomem *ref_div_addr = msspll_hw->base +REG_MSSPLL_REF_CR ; +void __iomem *postdiv_addr = msspll_hw->base +REG_MSSPLL_POSTDIV_CR ; +u32 mult, ref_div, postdiv; +int divider_setting; +unsigned long rate_before_ctrl, flags; + + mult =readl_relaxed (mult_addr) >>MSSPLL_FBDIV_SHIFT ; + mult &=clk_div_mask (MSSPLL_FBDIV_WIDTH ); + ref_div =readl_relaxed (ref_div_addr) >>MSSPLL_REFDIV_SHIFT ; + ref_div &=clk_div_mask (MSSPLL_REFDIV_WIDTH ); + + rate_before_ctrl = rate * (ref_div *MSSPLL_FIXED_DIV ) / mult; + divider_setting =divider_get_val (rate_before_ctrl, prate,NULL ,MSSPLL_POSTDIV_WIDTH , + msspll_hw->flags); + +if (divider_setting <0 ) +return divider_setting; + +spin_lock_irqsave (&mpfs_clk_lock, flags); + + postdiv =readl_relaxed (postdiv_addr); + postdiv &= ~(clk_div_mask (MSSPLL_POSTDIV_WIDTH ) <<MSSPLL_POSTDIV_SHIFT ); +writel_relaxed (postdiv, postdiv_addr); + +spin_unlock_irqrestore (&mpfs_clk_lock, flags); + +return 0 ; +} +static const struct clk_ops mpfs_clk_msspll_ops = { .recalc_rate = mpfs_clk_msspll_recalc_rate, + .round_rate = mpfs_clk_msspll_round_rate, + .set_rate = mpfs_clk_msspll_set_rate, };#define CLK_PLL (_id, _name, _parent, _shift, _width, _flags, _offset) { \
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v3 8/13 clk: microchip: mpfs: move id & offset out of clock structs
In reply to Conor DooleyThe id and offset are the only thing differentiating the clock structs from "regular" clock structures. On the pretext of converting to more normal structures, move the id and offset out of the clock structs and into the hw structs instead.
--- drivers/clk/microchip/clk-mpfs.c | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-)
drivers/clk/microchip/clk-mpfs.c +15 -15
@@ -53,8 +53,6 @@ struct mpfs_msspll_hw_clock {struct mpfs_cfg_clock {const struct clk_div_table *table; -unsigned int id; -u32 reg_offset;u8 shift;u8 width;u8 flags;
@@ -65,12 +63,13 @@ struct mpfs_cfg_hw_clock {void __iomem *sys_base;struct clk_hw hw;struct clk_init_data init; +unsigned int id; +u32 reg_offset; };#define to_mpfs_cfg_clk (_hw) container_of(_hw, struct mpfs_cfg_hw_clock, hw)struct mpfs_periph_clock { -unsigned int id;u8 shift; };
@@ -78,6 +77,7 @@ struct mpfs_periph_hw_clock {struct mpfs_periph_clock periph;void __iomem *sys_base;struct clk_hw hw; +unsigned int id; };#define to_mpfs_periph_clk (_hw) container_of(_hw, struct mpfs_periph_hw_clock, hw)
@@ -243,7 +243,7 @@ static unsigned long mpfs_cfg_clk_recalc_rate(struct clk_hw *hw, unsigned long pvoid __iomem *base_addr = cfg_hw->sys_base;u32 val; - val =readl_relaxed (base_addr + cfg->reg_offset) >> cfg->shift; + val =readl_relaxed (base_addr + cfg_hw->reg_offset) >> cfg->shift; val &=clk_div_mask (cfg->width);return divider_recalc_rate (hw, prate, val, cfg->table, cfg->flags, cfg->width);
@@ -272,10 +272,10 @@ static int mpfs_cfg_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsignedreturn divider_setting;spin_lock_irqsave (&mpfs_clk_lock, flags); - val =readl_relaxed (base_addr + cfg->reg_offset); + val =readl_relaxed (base_addr + cfg_hw->reg_offset); val &= ~(clk_div_mask (cfg->width) << cfg_hw->cfg.shift); val |= divider_setting << cfg->shift; -writel_relaxed (val, base_addr + cfg->reg_offset); +writel_relaxed (val, base_addr + cfg_hw->reg_offset);spin_unlock_irqrestore (&mpfs_clk_lock, flags);
@@ -289,11 +289,11 @@ static const struct clk_ops mpfs_clk_cfg_ops = { };#define CLK_CFG (_id, _name, _parent, _shift, _width, _table, _flags, _offset) { \ - .cfg.id = _id, \ + .id = _id, \ .cfg.shift = _shift, \ .cfg.width = _width, \ .cfg.table = _table, \ - .cfg.reg_offset = _offset, \ + .reg_offset = _offset, \ .cfg.flags = _flags, \ .hw.init = CLK_HW_INIT(_name, _parent, &mpfs_clk_cfg_ops, 0), \ }
@@ -306,11 +306,11 @@ static struct mpfs_cfg_hw_clock mpfs_cfg_clks[] = {CLK_CFG (CLK_AHB ,"clk_ahb" ,"clk_msspll" ,4 ,2 , mpfs_div_ahb_table,0 , REG_CLOCK_CONFIG_CR), { - .cfg.id = CLK_RTCREF, + .id = CLK_RTCREF, .cfg.shift = 0, .cfg.width = 12, .cfg.table = mpfs_div_rtcref_table, - .cfg.reg_offset = REG_RTC_CLOCK_CR, + .reg_offset = REG_RTC_CLOCK_CR, .cfg.flags = CLK_DIVIDER_ONE_BASED, .hw.init = CLK_HW_INIT_PARENTS_DATA("clk_rtcref", mpfs_ext_ref, &mpfs_clk_cfg_ops, 0),
@@ -338,9 +338,9 @@ static int mpfs_clk_register_cfgs(struct device *dev, struct mpfs_cfg_hw_clock * ret =mpfs_clk_register_cfg (dev, cfg_hw, sys_base);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , - cfg_hw->cfg.id); + cfg_hw->id); - id = cfg_hw->cfg.id; + id = cfg_hw->id; data->hw_data.hws[id] = &cfg_hw->hw; }
@@ -408,7 +408,7 @@ static const struct clk_ops mpfs_periph_clk_ops = { };#define CLK_PERIPH (_id, _name, _parent, _shift, _flags) { \ - .periph.id = _id, \ + .id = _id, \ .periph.shift = _shift, \ .hw.init = CLK_HW_INIT_HW(_name, _parent, &mpfs_periph_clk_ops, \ _flags), \
@@ -482,9 +482,9 @@ static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_c ret =mpfs_clk_register_periph (dev, periph_hw, sys_base);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , - periph_hw->periph.id); + periph_hw->id); - id = periph_hws[i].periph.id; + id = periph_hws[i].id; data->hw_data.hws[id] = &periph_hw->hw; }
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v3 9/13 clk: microchip: mpfs: simplify control reg access
In reply to Conor DooleyThe control reg addresses are known when the clocks are registered, so we can, instead of assigning a base pointer to the structs, assign the control reg addresses directly. Accordingly, remove the interim variables used during reads/writes to those registers.
--- drivers/clk/microchip/clk-mpfs.c | 42 +++++++++++++------------------- 1 file changed, 17 insertions(+), 25 deletions(-)
drivers/clk/microchip/clk-mpfs.c +17 -25
@@ -52,6 +52,7 @@ struct mpfs_msspll_hw_clock {#define to_mpfs_msspll_clk (_hw) container_of(_hw, struct mpfs_msspll_hw_clock, hw)struct mpfs_cfg_clock { +void __iomem *reg;const struct clk_div_table *table;u8 shift;u8 width;
@@ -60,7 +61,6 @@ struct mpfs_cfg_clock {struct mpfs_cfg_hw_clock {struct mpfs_cfg_clock cfg; -void __iomem *sys_base;struct clk_hw hw;struct clk_init_data init;unsigned int id;
@@ -70,12 +70,12 @@ struct mpfs_cfg_hw_clock {#define to_mpfs_cfg_clk (_hw) container_of(_hw, struct mpfs_cfg_hw_clock, hw)struct mpfs_periph_clock { +void __iomem *reg;u8 shift; };struct mpfs_periph_hw_clock {struct mpfs_periph_clock periph; -void __iomem *sys_base;struct clk_hw hw;unsigned int id; };
@@ -214,14 +214,13 @@ static int mpfs_clk_register_msspll(struct device *dev, struct mpfs_msspll_hw_clstatic int mpfs_clk_register_mssplls (struct device *dev,struct mpfs_msspll_hw_clock *msspll_hws,unsigned int num_clks,struct mpfs_clock_data *data) { -void __iomem *base = data->msspll_base;unsigned int i;int ret;for (i =0 ; i < num_clks; i++) {struct mpfs_msspll_hw_clock *msspll_hw = &msspll_hws[i]; - ret =mpfs_clk_register_msspll (dev, msspll_hw, base); + ret =mpfs_clk_register_msspll (dev, msspll_hw, data->msspll_base);if (ret)return dev_err_probe (dev, ret,"failed to register msspll id: %d\n" ,CLK_MSSPLL );
@@ -240,10 +239,9 @@ static unsigned long mpfs_cfg_clk_recalc_rate(struct clk_hw *hw, unsigned long p {struct mpfs_cfg_hw_clock *cfg_hw =to_mpfs_cfg_clk (hw);struct mpfs_cfg_clock *cfg = &cfg_hw->cfg; -void __iomem *base_addr = cfg_hw->sys_base;u32 val; - val =readl_relaxed (base_addr + cfg_hw->reg_offset) >> cfg->shift; + val =readl_relaxed (cfg->reg) >> cfg->shift; val &=clk_div_mask (cfg->width);return divider_recalc_rate (hw, prate, val, cfg->table, cfg->flags, cfg->width);
@@ -261,7 +259,6 @@ static int mpfs_cfg_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned {struct mpfs_cfg_hw_clock *cfg_hw =to_mpfs_cfg_clk (hw);struct mpfs_cfg_clock *cfg = &cfg_hw->cfg; -void __iomem *base_addr = cfg_hw->sys_base;unsigned long flags;u32 val;int divider_setting;
@@ -272,10 +269,10 @@ static int mpfs_cfg_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsignedreturn divider_setting;spin_lock_irqsave (&mpfs_clk_lock, flags); - val =readl_relaxed (base_addr + cfg_hw->reg_offset); + val =readl_relaxed (cfg->reg); val &= ~(clk_div_mask (cfg->width) << cfg_hw->cfg.shift); val |= divider_setting << cfg->shift; -writel_relaxed (val, base_addr + cfg_hw->reg_offset); +writel_relaxed (val, cfg->reg);spin_unlock_irqrestore (&mpfs_clk_lock, flags);
@@ -318,9 +315,9 @@ static struct mpfs_cfg_hw_clock mpfs_cfg_clks[] = { };static int mpfs_clk_register_cfg (struct device *dev,struct mpfs_cfg_hw_clock *cfg_hw, -void __iomem *sys_base) +void __iomem *base) { - cfg_hw->sys_base = sys_base; + cfg_hw->cfg.reg = base + cfg_hw->reg_offset;return devm_clk_hw_register (dev, &cfg_hw->hw); }
@@ -328,14 +325,13 @@ static int mpfs_clk_register_cfg(struct device *dev, struct mpfs_cfg_hw_clock *cstatic int mpfs_clk_register_cfgs (struct device *dev,struct mpfs_cfg_hw_clock *cfg_hws,unsigned int num_clks,struct mpfs_clock_data *data) { -void __iomem *sys_base = data->base;unsigned int i, id;int ret;for (i =0 ; i < num_clks; i++) {struct mpfs_cfg_hw_clock *cfg_hw = &cfg_hws[i]; - ret =mpfs_clk_register_cfg (dev, cfg_hw, sys_base); + ret =mpfs_clk_register_cfg (dev, cfg_hw, data->base);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , cfg_hw->id);
@@ -355,15 +351,14 @@ static int mpfs_periph_clk_enable(struct clk_hw *hw) {struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw);struct mpfs_periph_clock *periph = &periph_hw->periph; -void __iomem *base_addr = periph_hw->sys_base;u32 reg, val;unsigned long flags;spin_lock_irqsave (&mpfs_clk_lock, flags); - reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); + reg =readl_relaxed (periph->reg); val = reg | (1u << periph->shift); -writel_relaxed (val, base_addr +REG_SUBBLK_CLOCK_CR ); +writel_relaxed (val, periph->reg);spin_unlock_irqrestore (&mpfs_clk_lock, flags);
@@ -374,15 +369,14 @@ static void mpfs_periph_clk_disable(struct clk_hw *hw) {struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw);struct mpfs_periph_clock *periph = &periph_hw->periph; -void __iomem *base_addr = periph_hw->sys_base;u32 reg, val;unsigned long flags;spin_lock_irqsave (&mpfs_clk_lock, flags); - reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); + reg =readl_relaxed (periph->reg); val = reg & ~(1u << periph->shift); -writel_relaxed (val, base_addr +REG_SUBBLK_CLOCK_CR ); +writel_relaxed (val, periph->reg);spin_unlock_irqrestore (&mpfs_clk_lock, flags); }
@@ -391,10 +385,9 @@ static int mpfs_periph_clk_is_enabled(struct clk_hw *hw) {struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw);struct mpfs_periph_clock *periph = &periph_hw->periph; -void __iomem *base_addr = periph_hw->sys_base;u32 reg; - reg =readl_relaxed (base_addr +REG_SUBBLK_CLOCK_CR ); + reg =readl_relaxed (periph->reg);if (reg & (1u << periph->shift))return 1 ;
@@ -462,9 +455,9 @@ static struct mpfs_periph_hw_clock mpfs_periph_clks[] = { };static int mpfs_clk_register_periph (struct device *dev,struct mpfs_periph_hw_clock *periph_hw, -void __iomem *sys_base) +void __iomem *base) { - periph_hw->sys_base = sys_base; + periph_hw->periph.reg = base +REG_SUBBLK_CLOCK_CR ;return devm_clk_hw_register (dev, &periph_hw->hw); }
@@ -472,14 +465,13 @@ static int mpfs_clk_register_periph(struct device *dev, struct mpfs_periph_hw_clstatic int mpfs_clk_register_periphs (struct device *dev,struct mpfs_periph_hw_clock *periph_hws,int num_clks,struct mpfs_clock_data *data) { -void __iomem *sys_base = data->base;unsigned int i, id;int ret;for (i =0 ; i < num_clks; i++) {struct mpfs_periph_hw_clock *periph_hw = &periph_hws[i]; - ret =mpfs_clk_register_periph (dev, periph_hw, sys_base); + ret =mpfs_clk_register_periph (dev, periph_hw, data->base);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , periph_hw->id);
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v3 10/13 clk: microchip: mpfs: delete 2 line mpfs_clk_register_foo()
In reply to Conor DooleyThe register functions are now comprised of only a single operation each and no longer add anything to the driver. Delete them.
--- drivers/clk/microchip/clk-mpfs.c | 33 ++++++-------------------------- 1 file changed, 6 insertions(+), 27 deletions(-)
drivers/clk/microchip/clk-mpfs.c +6 -27
@@ -203,14 +203,6 @@ static struct mpfs_msspll_hw_clock mpfs_msspll_clks[] = { MSSPLL_FBDIV_WIDTH, 0, REG_MSSPLL_SSCG_2_CR), }; -static int mpfs_clk_register_msspll (struct device *dev,struct mpfs_msspll_hw_clock *msspll_hw, -void __iomem *base) -{ - msspll_hw->base = base; - -return devm_clk_hw_register (dev, &msspll_hw->hw); -} -static int mpfs_clk_register_mssplls (struct device *dev,struct mpfs_msspll_hw_clock *msspll_hws,unsigned int num_clks,struct mpfs_clock_data *data) {
@@ -220,7 +212,8 @@ static int mpfs_clk_register_mssplls(struct device *dev, struct mpfs_msspll_hw_cfor (i =0 ; i < num_clks; i++) {struct mpfs_msspll_hw_clock *msspll_hw = &msspll_hws[i]; - ret =mpfs_clk_register_msspll (dev, msspll_hw, data->msspll_base); + msspll_hw->base = data->msspll_base; + ret =devm_clk_hw_register (dev, &msspll_hw->hw);if (ret)return dev_err_probe (dev, ret,"failed to register msspll id: %d\n" ,CLK_MSSPLL );
@@ -314,14 +307,6 @@ static struct mpfs_cfg_hw_clock mpfs_cfg_clks[] = { } }; -static int mpfs_clk_register_cfg (struct device *dev,struct mpfs_cfg_hw_clock *cfg_hw, -void __iomem *base) -{ - cfg_hw->cfg.reg = base + cfg_hw->reg_offset; - -return devm_clk_hw_register (dev, &cfg_hw->hw); -} -static int mpfs_clk_register_cfgs (struct device *dev,struct mpfs_cfg_hw_clock *cfg_hws,unsigned int num_clks,struct mpfs_clock_data *data) {
@@ -331,7 +316,8 @@ static int mpfs_clk_register_cfgs(struct device *dev, struct mpfs_cfg_hw_clock *for (i =0 ; i < num_clks; i++) {struct mpfs_cfg_hw_clock *cfg_hw = &cfg_hws[i]; - ret =mpfs_clk_register_cfg (dev, cfg_hw, data->base); + cfg_hw->cfg.reg = data->base + cfg_hw->reg_offset; + ret =devm_clk_hw_register (dev, &cfg_hw->hw);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , cfg_hw->id);
@@ -454,14 +440,6 @@ static struct mpfs_periph_hw_clock mpfs_periph_clks[] = { CLK_PERIPH(CLK_CFM, "clk_periph_cfm", PARENT_CLK(AHB), 29, 0), }; -static int mpfs_clk_register_periph (struct device *dev,struct mpfs_periph_hw_clock *periph_hw, -void __iomem *base) -{ - periph_hw->periph.reg = base +REG_SUBBLK_CLOCK_CR ; - -return devm_clk_hw_register (dev, &periph_hw->hw); -} -static int mpfs_clk_register_periphs (struct device *dev,struct mpfs_periph_hw_clock *periph_hws,int num_clks,struct mpfs_clock_data *data) {
@@ -471,7 +449,8 @@ static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_cfor (i =0 ; i < num_clks; i++) {struct mpfs_periph_hw_clock *periph_hw = &periph_hws[i]; - ret =mpfs_clk_register_periph (dev, periph_hw, data->base); + periph_hw->periph.reg = data->base +REG_SUBBLK_CLOCK_CR ; + ret =devm_clk_hw_register (dev, &periph_hw->hw);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , periph_hw->id);
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v3 11/13 clk: microchip: mpfs: convert cfg_clk to clk_divider
In reply to Conor DooleyThe cfg_clk struct is now just a redefinition of the clk_divider struct with custom implentations of the ops, that implement an extra level of redirection. Remove the custom struct and replace it with clk_divider.
--- drivers/clk/microchip/clk-mpfs.c | 78 ++++---------------------------- 1 file changed, 9 insertions(+), 69 deletions(-)
drivers/clk/microchip/clk-mpfs.c +9 -69
@@ -51,24 +51,13 @@ struct mpfs_msspll_hw_clock {#define to_mpfs_msspll_clk (_hw) container_of(_hw, struct mpfs_msspll_hw_clock, hw) -struct mpfs_cfg_clock { -void __iomem *reg; -const struct clk_div_table *table; -u8 shift; -u8 width; -u8 flags; -}; -struct mpfs_cfg_hw_clock { -struct mpfs_cfg_clock cfg; -struct clk_hw hw; +struct clk_divider cfg;struct clk_init_data init;unsigned int id;u32 reg_offset; }; -#define to_mpfs_cfg_clk (_hw) container_of(_hw, struct mpfs_cfg_hw_clock, hw) -struct mpfs_periph_clock {void __iomem *reg;u8 shift;
@@ -228,56 +217,6 @@ static int mpfs_clk_register_mssplls(struct device *dev, struct mpfs_msspll_hw_c* "CFG" clocks */ -static unsigned long mpfs_cfg_clk_recalc_rate (struct clk_hw *hw,unsigned long prate) -{ -struct mpfs_cfg_hw_clock *cfg_hw =to_mpfs_cfg_clk (hw); -struct mpfs_cfg_clock *cfg = &cfg_hw->cfg; -u32 val; - - val =readl_relaxed (cfg->reg) >> cfg->shift; - val &=clk_div_mask (cfg->width); - -return divider_recalc_rate (hw, prate, val, cfg->table, cfg->flags, cfg->width); -} - -static long mpfs_cfg_clk_round_rate (struct clk_hw *hw,unsigned long rate,unsigned long *prate) -{ -struct mpfs_cfg_hw_clock *cfg_hw =to_mpfs_cfg_clk (hw); -struct mpfs_cfg_clock *cfg = &cfg_hw->cfg; - -return divider_round_rate (hw, rate, prate, cfg->table, cfg->width,0 ); -} - -static int mpfs_cfg_clk_set_rate (struct clk_hw *hw,unsigned long rate,unsigned long prate) -{ -struct mpfs_cfg_hw_clock *cfg_hw =to_mpfs_cfg_clk (hw); -struct mpfs_cfg_clock *cfg = &cfg_hw->cfg; -unsigned long flags; -u32 val; -int divider_setting; - - divider_setting =divider_get_val (rate, prate, cfg->table, cfg->width,0 ); - -if (divider_setting <0 ) -return divider_setting; - -spin_lock_irqsave (&mpfs_clk_lock, flags); - val =readl_relaxed (cfg->reg); - val &= ~(clk_div_mask (cfg->width) << cfg_hw->cfg.shift); - val |= divider_setting << cfg->shift; -writel_relaxed (val, cfg->reg); - -spin_unlock_irqrestore (&mpfs_clk_lock, flags); - -return 0 ; -} - -static const struct clk_ops mpfs_clk_cfg_ops = { - .recalc_rate = mpfs_cfg_clk_recalc_rate, - .round_rate = mpfs_cfg_clk_round_rate, - .set_rate = mpfs_cfg_clk_set_rate, -}; -#define CLK_CFG (_id, _name, _parent, _shift, _width, _table, _flags, _offset) { \ .id = _id, \ .cfg.shift = _shift, \
@@ -285,7 +224,8 @@ static const struct clk_ops mpfs_clk_cfg_ops = { .cfg.table = _table, \ .reg_offset = _offset, \ .cfg.flags = _flags, \ - .hw.init = CLK_HW_INIT(_name, _parent, &mpfs_clk_cfg_ops, 0), \ + .cfg.hw.init = CLK_HW_INIT(_name, _parent, &clk_divider_ops, 0), \ + .cfg.lock = &mpfs_clk_lock, \ }static struct mpfs_cfg_hw_clock mpfs_cfg_clks[] = {
@@ -302,8 +242,8 @@ static struct mpfs_cfg_hw_clock mpfs_cfg_clks[] = { .cfg.table = mpfs_div_rtcref_table, .reg_offset = REG_RTC_CLOCK_CR, .cfg.flags = CLK_DIVIDER_ONE_BASED, - .hw.init = - CLK_HW_INIT_PARENTS_DATA("clk_rtcref", mpfs_ext_ref, &mpfs_clk_cfg_ops, 0), + .cfg.hw.init = + CLK_HW_INIT_PARENTS_DATA("clk_rtcref", mpfs_ext_ref, &clk_divider_ops, 0), } };
@@ -317,13 +257,13 @@ static int mpfs_clk_register_cfgs(struct device *dev, struct mpfs_cfg_hw_clock *struct mpfs_cfg_hw_clock *cfg_hw = &cfg_hws[i]; cfg_hw->cfg.reg = data->base + cfg_hw->reg_offset; - ret =devm_clk_hw_register (dev, &cfg_hw->hw); + ret =devm_clk_hw_register (dev, &cfg_hw->cfg.hw);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , cfg_hw->id); id = cfg_hw->id; - data->hw_data.hws[id] = &cfg_hw->hw; + data->hw_data.hws[id] = &cfg_hw->cfg.hw; }return 0 ;
@@ -393,7 +333,7 @@ static const struct clk_ops mpfs_periph_clk_ops = { _flags), \ } -#define PARENT_CLK (PARENT ) (&mpfs_cfg_clks[CLK_##PARENT].hw) +#define PARENT_CLK (PARENT ) (&mpfs_cfg_clks[CLK_##PARENT].cfg.hw)/* * Critical clocks:
@@ -413,7 +353,7 @@ static struct mpfs_periph_hw_clock mpfs_periph_clks[] = {CLK_PERIPH (CLK_MAC1 ,"clk_periph_mac1" ,PARENT_CLK (AHB ),2 ,0 ),CLK_PERIPH (CLK_MMC ,"clk_periph_mmc" ,PARENT_CLK (AHB ),3 ,0 ),CLK_PERIPH (CLK_TIMER ,"clk_periph_timer" , - &mpfs_cfg_clks[CLK_RTCREF -RTCREF_OFFSET ].hw,4 ,0 ), + &mpfs_cfg_clks[CLK_RTCREF -RTCREF_OFFSET ].cfg.hw,4 ,0 ),CLK_PERIPH (CLK_MMUART0 ,"clk_periph_mmuart0" ,PARENT_CLK (AHB ),5 ,CLK_IS_CRITICAL ),CLK_PERIPH (CLK_MMUART1 ,"clk_periph_mmuart1" ,PARENT_CLK (AHB ),6 ,0 ), CLK_PERIPH(CLK_MMUART2, "clk_periph_mmuart2", PARENT_CLK(AHB), 7, 0),
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v3 12/13 clk: microchip: mpfs: convert periph_clk to clk_gate
In reply to Conor DooleyWith the reset code moved to the recently added reset controller, there is no need for custom ops any longer. Remove the custom ops and the custom struct by converting to a clk_gate.
--- drivers/clk/microchip/clk-mpfs.c | 72 +++----------------------------- 1 file changed, 6 insertions(+), 66 deletions(-)
drivers/clk/microchip/clk-mpfs.c +6 -66
@@ -58,19 +58,11 @@ struct mpfs_cfg_hw_clock {u32 reg_offset; }; -struct mpfs_periph_clock { -void __iomem *reg; -u8 shift; -}; -struct mpfs_periph_hw_clock { -struct mpfs_periph_clock periph; -struct clk_hw hw; +struct clk_gate periph;unsigned int id; }; -#define to_mpfs_periph_clk (_hw) container_of(_hw, struct mpfs_periph_hw_clock, hw) -/* * mpfs_clk_lock prevents anything else from writing to the * mpfs clk block while a software locked register is being written.
@@ -273,64 +265,12 @@ static int mpfs_clk_register_cfgs(struct device *dev, struct mpfs_cfg_hw_clock ** peripheral clocks - devices connected to axi or ahb buses. */ -static int mpfs_periph_clk_enable (struct clk_hw *hw) -{ -struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw); -struct mpfs_periph_clock *periph = &periph_hw->periph; -u32 reg, val; -unsigned long flags; - -spin_lock_irqsave (&mpfs_clk_lock, flags); - - reg =readl_relaxed (periph->reg); - val = reg | (1u << periph->shift); -writel_relaxed (val, periph->reg); - -spin_unlock_irqrestore (&mpfs_clk_lock, flags); - -return 0 ; -} - -static void mpfs_periph_clk_disable (struct clk_hw *hw) -{ -struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw); -struct mpfs_periph_clock *periph = &periph_hw->periph; -u32 reg, val; -unsigned long flags; - -spin_lock_irqsave (&mpfs_clk_lock, flags); - - reg =readl_relaxed (periph->reg); - val = reg & ~(1u << periph->shift); -writel_relaxed (val, periph->reg); - -spin_unlock_irqrestore (&mpfs_clk_lock, flags); -} - -static int mpfs_periph_clk_is_enabled (struct clk_hw *hw) -{ -struct mpfs_periph_hw_clock *periph_hw =to_mpfs_periph_clk (hw); -struct mpfs_periph_clock *periph = &periph_hw->periph; -u32 reg; - - reg =readl_relaxed (periph->reg); -if (reg & (1u << periph->shift)) -return 1 ; - -return 0 ; -} - -static const struct clk_ops mpfs_periph_clk_ops = { - .enable = mpfs_periph_clk_enable, - .disable = mpfs_periph_clk_disable, - .is_enabled = mpfs_periph_clk_is_enabled, -}; -#define CLK_PERIPH (_id, _name, _parent, _shift, _flags) { \ .id = _id, \ - .periph.shift = _shift, \ - .hw.init = CLK_HW_INIT_HW(_name, _parent, &mpfs_periph_clk_ops, \ + .periph.bit_idx = _shift, \ + .periph.hw.init = CLK_HW_INIT_HW(_name, _parent, &clk_gate_ops, \ _flags), \ + .periph.lock = &mpfs_clk_lock, \ }#define PARENT_CLK (PARENT ) (&mpfs_cfg_clks[CLK_##PARENT].cfg.hw)
@@ -390,13 +330,13 @@ static int mpfs_clk_register_periphs(struct device *dev, struct mpfs_periph_hw_cstruct mpfs_periph_hw_clock *periph_hw = &periph_hws[i]; periph_hw->periph.reg = data->base +REG_SUBBLK_CLOCK_CR ; - ret =devm_clk_hw_register (dev, &periph_hw->hw); + ret =devm_clk_hw_register (dev, &periph_hw->periph.hw);if (ret)return dev_err_probe (dev, ret,"failed to register clock id: %d\n" , periph_hw->id); id = periph_hws[i].id; - data->hw_data.hws[id] = &periph_hw->hw; + data->hw_data.hws[id] = &periph_hw->periph.hw; }return 0 ;
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v3 13/13 clk: microchip: mpfs: update module authorship & licencing
In reply to Conor DooleyPadmarao wrote the driver in its original, pre upstream form. Daire & myself have been responsible for getting it upstreamable and subsequent development.
Move Daire out of the blurb & into a MODULE_AUTHOR entry & add entries for myself and Padmarao.
While we are at it, convert the MODULE_LICENSE field to its preferred form of "GPL".
--- drivers/clk/microchip/clk-mpfs.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/clk/microchip/clk-mpfs.c +7 -3
@@ -1,7 +1,8 @@// SPDX-License-Identifier: GPL-2.0-only /* -* Daire McNamara,<[email protected]> -* Copyright (C) 2020 Microchip Technology Inc. All rights reserved. +* PolarFire SoC MSS/core complex clock control +* +* Copyright (C) 2020-2022 Microchip Technology Inc. All rights reserved. */ #include <linux/auxiliary_bus.h> #include <linux/clk-provider.h>
@@ -513,4 +514,7 @@ static void __exit clk_mpfs_exit(void)module_exit (clk_mpfs_exit);MODULE_DESCRIPTION ("Microchip PolarFire SoC Clock Driver" ); -MODULE_LICENSE ("GPL v2" ); +MODULE_AUTHOR ("Padmarao Begari <[email protected]>" ); +MODULE_AUTHOR ("Daire McNamara <[email protected]>" ); +MODULE_AUTHOR ("Conor Dooley <[email protected]>" ); +MODULE_LICENSE ("GPL" );
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv