Skip to contentSkip to conversation

arm64: dts: imx8mm-kontron: Improvements and OSM board support

PATCH Superseded Frieder Schrempf 3 participants 11 messages Aug 22, 2022 – Aug 23, 2022

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover arm64: dts: imx8mm-kontron: Improvements and OSM board support

From: Frieder Schrempf <[email protected]>

This set contains a few improvements for the imx8mm-kontron devicetrees (patch 3-7) and support for a new SoM (patch 8, including baseboard) that complies to the Open Standard Module (OSM) 1.0 hardware specification, size S
(https://sget.org/standards/osm).

It also includes binding changes in patch 1 and 2.

Changes in v3:
* drop patch for 2 which was applied separately
* rebase on v6.0-rc1
* rename compatibles and file names

Changes in v2:
* move binding changes to beginning of patchset
* Allow arbitrary regulator names in PCA9450 bindings
* Use voltage rail names from schematic for PMIC regulator-names
* Add SPI NOR partition layout to devicetree
* Remove unneeded header include
* Add tags

Frieder Schrempf (8):
dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM
SoM/board
dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board
arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model
strings
arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card
IO voltage
arm64: dts: imx8mm-kontron: Remove low DDRC operating point
arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for
PMIC regulator-names
arm64: dts: imx8mm-kontron: Add SPI NOR partition layout
arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S

 .../devicetree/bindings/arm/fsl.yaml          |  13 +-
 arch/arm64/boot/dts/freescale/Makefile        |   3 +-
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 376 ++++++++++++++++++
 ...tron-n801x-s.dts => imx8mm-kontron-bl.dts} |   7 +-
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 330 +++++++++++++++
 ...-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} |  53 ++-
 6 files changed, 757 insertions(+), 25 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
 rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} (96%)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
 rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} (87%)
Signature · 1 line
2.37.1
#1 lore raw

PATCH v3 1/8 dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM SoM/board

From: Frieder Schrempf <[email protected]>

This updates the bindings in order to use names for the boards that follow the latest convention used by Kontron marketing.

By updating we make sure, that we can maintain this more easily in future and make sure that the proper devicetree can be selected for the hardware.

---
Changes in v3:
* new patch

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/arm/fsl.yaml +3 -3
index 7431579ab0e8..4dcfa27044f0 100644
@@ -831,7 +831,7 @@ properties:
               - gw,imx8mm-gw7901          # i.MX8MM Gateworks Board
               - gw,imx8mm-gw7902          # i.MX8MM Gateworks Board
               - gw,imx8mm-gw7903          # i.MX8MM Gateworks Board
-              - kontron,imx8mm-n801x-som  # i.MX8MM Kontron SL (N801X) SOM
+              - kontron,imx8mm-sl         # i.MX8MM Kontron SL (N801X) SOM
               - menlo,mx8menlo            # i.MX8MM Menlo board with Verdin SoM
               - toradex,verdin-imx8mm     # Verdin iMX8M Mini Modules
               - toradex,verdin-imx8mm-nonwifi  # Verdin iMX8M Mini Modules without Wi-Fi / BT
@@ -850,8 +850,8 @@ properties:
 
       - description: Kontron BL i.MX8MM (N801X S) Board
         items:
-          - const: kontron,imx8mm-n801x-s
-          - const: kontron,imx8mm-n801x-som
+          - const: kontron,imx8mm-bl
+          - const: kontron,imx8mm-sl
           - const: fsl,imx8mm
 
       - description: Toradex Boards with Verdin iMX8M Mini Modules
Signature · 1 line
2.37.1
Acked-by on v3 1/8
#2 lore raw

Re: [PATCH v3 1/8] dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM SoM/board

Quoted 11 lines · Frieder Schrempf

From: Frieder Schrempf <[email protected]>

This updates the bindings in order to use names for the boards that follow the latest convention used by Kontron marketing.

By updating we make sure, that we can maintain this more easily in future and make sure that the proper devicetree can be selected for the hardware.

---

Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#3 lore raw

PATCH v3 2/8 dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

Add bindings for the Kontron BL i.MX8MM OSM-S board.

---
Changes in v3:
* rename compatibles
* rebase on v6.0-rc1

Changes in v2:
* add A-b tag from Krzysztof (Thanks!)

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +7 -0
index 4dcfa27044f0..2b5a4d293e25 100644
@@ -832,6 +832,7 @@ properties:
               - gw,imx8mm-gw7902          # i.MX8MM Gateworks Board
               - gw,imx8mm-gw7903          # i.MX8MM Gateworks Board
               - kontron,imx8mm-sl         # i.MX8MM Kontron SL (N801X) SOM
+              - kontron,imx8mm-osm-s      # i.MX8MM Kontron OSM-S (N802X) SOM
               - menlo,mx8menlo            # i.MX8MM Menlo board with Verdin SoM
               - toradex,verdin-imx8mm     # Verdin iMX8M Mini Modules
               - toradex,verdin-imx8mm-nonwifi  # Verdin iMX8M Mini Modules without Wi-Fi / BT
@@ -854,6 +855,12 @@ properties:
           - const: kontron,imx8mm-sl
           - const: fsl,imx8mm
 
+      - description: Kontron BL i.MX8MM OSM-S (N802X S) Board
+        items:
+          - const: kontron,imx8mm-bl-osm-s
+          - const: kontron,imx8mm-osm-s
+          - const: fsl,imx8mm
+
       - description: Toradex Boards with Verdin iMX8M Mini Modules
         items:
           - enum:
Signature · 1 line
2.37.1
#4 lore raw

PATCH v3 3/8 arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model strings

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

The official naming includes "SL" (SoM-Line) or "BL" (Board-Line). By updating we make sure, that we can maintain this more easily in future and make sure that the proper devicetree can be selected for the hardware.

---
Changes in v3:
* also rename compatibles and file names
* rebase on v6.0-rc1

Changes in v2:
* none

---
 arch/arm64/boot/dts/freescale/Makefile                        | 2 +-
 .../{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts}     | 4 ++--
 .../{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} | 4 ++--
 3 files changed, 5 insertions(+), 5 deletions(-)
 rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} (98%)
 rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} (98%)
arch/arm64/boot/dts/freescale/Makefile +1 -1
index 8bf7f7ecebaa..d014f7c4c888 100644
@@ -55,7 +55,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
-dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts renamed from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts +2 -2
similarity index 98%
rename from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
rename to arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index 23be1ec538ba..4e5828fa815b 100644
@@ -8,8 +8,8 @@
 #include "imx8mm-kontron-n801x-som.dtsi"
 
 / {
-	model = "Kontron i.MX8MM N801X S";
-	compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+	model = "Kontron BL i.MX8MM (N801X S)";
+	compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm";
 
 	aliases {
 		ethernet1 = &usbnet;
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi renamed from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi +2 -2
similarity index 98%
rename from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
rename to arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 8f90eb02550d..30299c2a98ea 100644
@@ -6,8 +6,8 @@
 #include "imx8mm.dtsi"
 
 / {
-	model = "Kontron i.MX8MM N801X SoM";
-	compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+	model = "Kontron SL i.MX8MM (N801X SOM)";
+	compatible = "kontron,imx8mm-sl", "fsl,imx8mm";
 
 	memory@40000000 {
 		device_type = "memory";
Signature · 1 line
2.37.1
#5 lore raw

PATCH v3 4/8 arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

It turns out that it is not necessary to declare the VSELECT signal as GPIO and let the PMIC driver set it to a fixed high level. This switches the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5 accordingly.

Instead we can do it like other boards already do and simply mux the VSELECT signal of the USDHC interface to the pin. This makes sure that the correct voltage is selected by setting the PMIC's SD_VSEL input to high or low accordingly.

---
Changes in v3:
* rebase on v6.0-rc1

Changes in v2:
* none

---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts  | 3 +++
 arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 2 --
 2 files changed, 3 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts +3 -0
index 4e5828fa815b..7af3c476fd9a 100644
@@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 };
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi +0 -2
index 30299c2a98ea..33179157f619 100644
@@ -86,7 +86,6 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -229,7 +228,6 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
-			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
Signature · 1 line
2.37.1
#6 lore raw

PATCH v3 5/8 arm64: dts: imx8mm-kontron: Remove low DDRC operating point

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

For some reason there is a problem with finding a DDR configuration that works on all operating points and all LPDDR4 types used on the SoM. Therefore the bootloader currently doesn't configure the lowest of the three operating points. Let's also skip this in the kernel devicetree to make sure it isn't used.

---
Changes in v3:
* rebase on v6.0-rc1

Changes in v2:
* none

---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 ----
 1 file changed, 4 deletions(-)
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi +0 -4
index 33179157f619..96ecdce67059 100644
@@ -46,10 +46,6 @@ &ddrc {
 	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
-		opp-25M {
-			opp-hz = /bits/ 64 <25000000>;
-		};
-
 		opp-100M {
 			opp-hz = /bits/ 64 <100000000>;
 		};
Signature · 1 line
2.37.1
#7 lore raw

PATCH v3 6/8 arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for PMIC regulator-names

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

Improve the naming of the regulators to contain the voltage rail names from the schematic.

---
Changes in v3:
* rebase on v6.0-rc1

Changes in v2:
* new patch

---
 .../boot/dts/freescale/imx8mm-kontron-sl.dtsi | 22 +++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi +11 -11
index 96ecdce67059..ce9c27619e26 100644
@@ -85,7 +85,7 @@ pca9450: pmic@25 {
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
-				regulator-name = "buck1";
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
@@ -96,7 +96,7 @@ reg_vdd_soc: BUCK1 {
 			};
 
 			reg_vdd_arm: BUCK2 {
-				regulator-name = "buck2";
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
@@ -107,7 +107,7 @@ reg_vdd_arm: BUCK2 {
 			};
 
 			reg_vdd_dram: BUCK3 {
-				regulator-name = "buck3";
+				regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
@@ -115,7 +115,7 @@ reg_vdd_dram: BUCK3 {
 			};
 
 			reg_vdd_3v3: BUCK4 {
-				regulator-name = "buck4";
+				regulator-name = "+3V3 (BUCK4)";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -123,7 +123,7 @@ reg_vdd_3v3: BUCK4 {
 			};
 
 			reg_vdd_1v8: BUCK5 {
-				regulator-name = "buck5";
+				regulator-name = "+1V8 (BUCK5)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -131,7 +131,7 @@ reg_vdd_1v8: BUCK5 {
 			};
 
 			reg_nvcc_dram: BUCK6 {
-				regulator-name = "buck6";
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
@@ -139,7 +139,7 @@ reg_nvcc_dram: BUCK6 {
 			};
 
 			reg_nvcc_snvs: LDO1 {
-				regulator-name = "ldo1";
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -147,7 +147,7 @@ reg_nvcc_snvs: LDO1 {
 			};
 
 			reg_vdd_snvs: LDO2 {
-				regulator-name = "ldo2";
+				regulator-name = "+0V8_VDD_SNVS (LDO2)";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -155,7 +155,7 @@ reg_vdd_snvs: LDO2 {
 			};
 
 			reg_vdda: LDO3 {
-				regulator-name = "ldo3";
+				regulator-name = "+1V8_VDDA (LDO3)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -163,7 +163,7 @@ reg_vdda: LDO3 {
 			};
 
 			reg_vdd_phy: LDO4 {
-				regulator-name = "ldo4";
+				regulator-name = "+0V9_VDD_PHY (LDO4)";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -171,7 +171,7 @@ reg_vdd_phy: LDO4 {
 			};
 
 			reg_nvcc_sd: LDO5 {
-				regulator-name = "ldo5";
+				regulator-name = "NVCC_SD (LDO5)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
Signature · 1 line
2.37.1
#8 lore raw

PATCH v3 7/8 arm64: dts: imx8mm-kontron: Add SPI NOR partition layout

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

This is the layout used by the bootloader. Add it to the kernel devicetree to make the same layout available in Linux and have the devicetrees synced.

---
Changes in v3:
* rebase on v6.0-rc1

Changes in v2:
* new patch

---
 .../boot/dts/freescale/imx8mm-kontron-sl.dtsi | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi +21 -0
index ce9c27619e26..c227ca813d9e 100644
@@ -66,6 +66,27 @@ flash@0 {
 		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
 		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x1E0000>;
+			};
+
+			partition@1 {
+				label = "env";
+				reg = <0x1E0000 0x10000>;
+			};
+
+			partition@2 {
+				label = "env_redundant";
+				reg = <0x1F0000 0x10000>;
+			};
+		};
 	};
 };
 
Signature · 1 line
2.37.1
#9 lore raw

PATCH v3 8/8 arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S

In reply to Frieder Schrempf

From: Frieder Schrempf <[email protected]>

This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM and the matching baseboard BL i.MX8MM OSM-S.

The SoM hardware complies to the Open Standard Module (OSM) 1.0 specification, size S (https://sget.org/standards/osm).

---
Changes in v3:
* rename devicetrees, compatibles and SoM model
* rebase on v6.0-rc1

Changes in v2:
* add SPI NOR partitions
* use voltage rail names for PMIC regulator-name
* drop unused header include

---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 376 ++++++++++++++++++
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 330 +++++++++++++++
 3 files changed, 707 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
arch/arm64/boot/dts/freescale/Makefile +1 -0
index d014f7c4c888..542e1d661f30 100644
@@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts new file +376 -0

376 lines not on this page · raw message

arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi new file +330 -0

330 lines not on this page · raw message

Signature · 1 line
2.37.1
#10 lore raw
In reply to Frieder Schrempf

Am 22.08.22 um 10:00 schrieb Frieder Schrempf:

Quoted 14 lines

From: Frieder Schrempf <[email protected]>

This set contains a few improvements for the imx8mm-kontron devicetrees (patch 3-7) and support for a new SoM (patch 8, including baseboard) that complies to the Open Standard Module (OSM) 1.0 hardware specification, size S
(https://sget.org/standards/osm).

It also includes binding changes in patch 1 and 2.

Changes in v3:
* drop patch for 2 which was applied separately
* rebase on v6.0-rc1
* rename compatibles and file names

Quoted 7 lines

Changes in v2:
* move binding changes to beginning of patchset
* Allow arbitrary regulator names in PCA9450 bindings
* Use voltage rail names from schematic for PMIC regulator-names
* Add SPI NOR partition layout to devicetree
* Remove unneeded header include
* Add tags

Please ignore this series. I accidentally resent v3 instead of sending v4. Sorry for the noise!