imx: kontron-sl-mx8mm: Improvements and OSM board support
Subsystems (2)
v3 cover imx: kontron-sl-mx8mm: Improvements and OSM board support
From: Frieder Schrempf <[email protected]>
This set contains several improvements for the kontron-sl-mx8mm board configuration (patches 1-17, 19) and support for a new SoM (patch 18, including baseboard) that complies to the Open Standard Module (OSM) 1.0 hardware specification, size S (https://sget.org/standards/osm).
This also syncs the devicetrees with the pending changes in Linux (see [1]).
Changes in v3:
* add Fabio's R-b tags (Thanks!)
* fix OSM-S SoM name to match official name
* fix docs to match official board names
* adjust devicetree names and compatibles
* fix printing of RAM size
* add missing Makefile entry for new dtb
* fix hex numbers and unit addresses in SPI NOR partitions
Changes in v2:
* rebase on u-boot-imx/master
* new patches 2-5, 19
* fix printf warning in board/kontron/sl-mx8mm/spl.c
* remove unused pinmux definitions in board/kontron/sl-mx8mm/spl.c
* describe SPI NOR partitions in devicetree
* move environment to end of SPI NOR
* Add tags
[1] https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/
Frieder Schrempf (19):
imx: kontron-sl-mx8mm: Remove LVDS board type and devicetrees
imx: kontron-sl-mx8mm: Add support for loading from SPI NOR in SPL
imx: kontron-sl-mx8mm: Remove custom board_boot_order() workaround
imx: kontron-sl-mx8mm: Increase CONFIG_SYS_CBSIZE to 2K
imx: kontron-sl-mx8mm: Enable MTD command
imx: kontron-sl-mx8mm: Add redundant environment and SPI NOR
partitions
imx: kontron-sl-mx8mm: Enable environment in MMC
imx: kontron-sl-mx8mm: Migrate to use CONFIG_EXTRA_ENV_TEXT
imx: kontron-sl-mx8mm: Enable bootaux command
imx: kontron-sl-mx8mm: lpddr4_timing.c: Add spaces for proper
alignment
imx: kontron-sl-mx8mm: Remove 100mt DDR setpoint
imx: kontron-sl-mx8mm: Use new LPDDR4 config parameters
imx: kontron-sl-mx8mm: Prepare for other i.MX8MM SoM types
imx: kontron-sl-mx8mm: Adjust devicetree names, compatibles and model
strings
imx: kontron-sl-mx8mm: Use the VSELECT signal to switch SD card IO
voltage
imx: kontron-sl-mx8mm: Use voltage rail names from schematic for PMIC
regulator-names
imx: kontron-sl-mx8mm: Simplify code in spl.c
imx: kontron-sl-mx8mm: Add support for Kontron Electronics SoM SL
i.MX8MM OSM-S
imx: kontron-sl-mx8mm: Prepare for I2C display detection in
environment script
arch/arm/dts/Makefile | 4 +-
...i => imx8mm-kontron-bl-common-u-boot.dtsi} | 21 +-
.../dts/imx8mm-kontron-bl-osm-s-u-boot.dtsi | 14 +
arch/arm/dts/imx8mm-kontron-bl-osm-s.dts | 376 ++++
arch/arm/dts/imx8mm-kontron-bl-u-boot.dtsi | 14 +
...tron-n801x-s.dts => imx8mm-kontron-bl.dts} | 9 +-
.../imx8mm-kontron-n801x-s-lvds-u-boot.dtsi | 6 -
arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dts | 117 -
.../dts/imx8mm-kontron-n801x-s-u-boot.dtsi | 6 -
arch/arm/dts/imx8mm-kontron-osm-s.dtsi | 330 +++
...-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} | 53 +-
board/kontron/sl-mx8mm/MAINTAINERS | 2 +-
board/kontron/sl-mx8mm/lpddr4_timing.c | 1969 ++++++++---------
board/kontron/sl-mx8mm/sl-mx8mm.c | 45 +
board/kontron/sl-mx8mm/sl-mx8mm.env | 7 +
board/kontron/sl-mx8mm/spl.c | 115 +-
configs/kontron-sl-mx8mm_defconfig | 19 +-
doc/board/kontron/sl-mx8mm.rst | 13 +-
include/configs/kontron-sl-mx8mm.h | 16 +-
19 files changed, 1810 insertions(+), 1326 deletions(-)
rename arch/arm/dts/{imx8mm-kontron-n801x-u-boot.dtsi => imx8mm-kontron-bl-common-u-boot.dtsi} (83%)
create mode 100644 arch/arm/dts/imx8mm-kontron-bl-osm-s-u-boot.dtsi
create mode 100644 arch/arm/dts/imx8mm-kontron-bl-osm-s.dts
create mode 100644 arch/arm/dts/imx8mm-kontron-bl-u-boot.dtsi
rename arch/arm/dts/{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} (96%)
delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-s-lvds-u-boot.dtsi
delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dts
delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-s-u-boot.dtsi
create mode 100644 arch/arm/dts/imx8mm-kontron-osm-s.dtsi
rename arch/arm/dts/{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} (87%)
create mode 100644 board/kontron/sl-mx8mm/sl-mx8mm.envSignature · 1 line
2.37.2
PATCH v3 1/19 imx: kontron-sl-mx8mm: Remove LVDS board type and devicetrees
From: Frieder Schrempf <[email protected]>
The display isn't and won't be used in U-Boot. Also the display setup is not yet supported in mainline Linux, so even for cases where the U-Boot devicetree is passed to the kernel there is currently no use for this configuration.
Selecting the proper configuration in the kernel FIT image automatically depending on the detected hardware can be handled by a script in the environment.
---
Changes in v3:
* none
Changes in v2:
* rebase on u-boot-imx/master
--- arch/arm/dts/Makefile | 1 - .../imx8mm-kontron-n801x-s-lvds-u-boot.dtsi | 6 - arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dts | 117 -------------- .../dts/imx8mm-kontron-n801x-s-u-boot.dtsi | 140 ++++++++++++++++- arch/arm/dts/imx8mm-kontron-n801x-u-boot.dtsi | 145 ------------------ board/kontron/sl-mx8mm/spl.c | 46 +----- configs/kontron-sl-mx8mm_defconfig | 1 - 7 files changed, 141 insertions(+), 315 deletions(-) delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-s-lvds-u-boot.dtsi delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dts delete mode 100644 arch/arm/dts/imx8mm-kontron-n801x-u-boot.dtsi
arch/arm/dts/Makefile +0 -1
@@ -940,7 +940,6 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-icore-mx8mm-ctouch2.dtb \ imx8mm-icore-mx8mm-edimm2.2.dtb \ imx8mm-kontron-n801x-s.dtb \ - imx8mm-kontron-n801x-s-lvds.dtb \ imx8mm-mx8menlo.dtb \ imx8mm-venice.dtb \ imx8mm-venice-gw71xx-0x.dtb \
arch/arm/dts/imx8mm-kontron-n801x-s-lvds-u-boot.dtsi deleted +0 -6
@@ -1,6 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2019 Kontron Electronics GmbH - */ - -#include "imx8mm-kontron-n801x-u-boot.dtsi"
arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dts deleted +0 -117
117 lines not on this page · raw message
arch/arm/dts/imx8mm-kontron-n801x-s-u-boot.dtsi +139 -1
143 lines not on this page · raw message
arch/arm/dts/imx8mm-kontron-n801x-u-boot.dtsi deleted +0 -145
145 lines not on this page · raw message
board/kontron/sl-mx8mm/spl.c +2 -44
90 lines not on this page · raw message
configs/kontron-sl-mx8mm_defconfig +0 -1
@@ -66,7 +66,6 @@ CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y -CONFIG_OF_LIST="imx8mm-kontron-n801x-s imx8mm-kontron-n801x-s-lvds" CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y CONFIG_NET_RANDOM_ETHADDR=y
Signature · 1 line
2.37.2
PATCH v3 1/19 imx: kontron-sl-mx8mm: Remove LVDS board type and devicetrees
Quoted 10 lines
From: Frieder Schrempf <[email protected]>
The display isn't and won't be used in U-Boot. Also the display setup is not yet supported in mainline Linux, so even for cases where the U-Boot devicetree is passed to the kernel there is currently no use for this configuration.
Selecting the proper configuration in the kernel FIT image automatically depending on the detected hardware can be handled by a script in the environment.Signed-off-by Frieder Schrempf <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v3 2/19 imx: kontron-sl-mx8mm: Add support for loading from SPI NOR in SPL
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
This was initially enabled, but got accidentally dropped while migrating Kconfig options and resyncing the defconfig in:
commit 9802154a94d6 ("configs: Resync with savedefconfig")
Let's enable this again to be able to boot from SPI NOR.
---
Changes in v3:
* none
Changes in v2:
* new patch
--- configs/kontron-sl-mx8mm_defconfig | 4 ++++ 1 file changed, 4 insertions(+)
configs/kontron-sl-mx8mm_defconfig +4 -0
@@ -19,6 +19,8 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SPL=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y CONFIG_SYS_LOAD_ADDR=0x42000000 CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y
@@ -43,6 +45,8 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_DM_SPI_FLASH=y CONFIG_SPL_POWER=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x58000 CONFIG_SPL_WATCHDOG=y CONFIG_SPL_ATF=y CONFIG_SYS_CBSIZE=256
Signature · 1 line
2.37.2
PATCH v3 2/19 imx: kontron-sl-mx8mm: Add support for loading from SPI NOR in SPL
Quoted 7 lines
From: Frieder Schrempf <[email protected]> This was initially enabled, but got accidentally dropped while migrating
Kconfigoptions and resyncing the defconfig in:
commit9802154a94d6("configs: Resync with savedefconfig") Let's enable this again to be able to boot from SPI NOR.Signed-off-by Frieder Schrempf <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================