Allwinner A31/A83T MIPI CSI-2 and A31 ISP / Platform Support
v5 cover Allwinner A31/A83T MIPI CSI-2 and A31 ISP / Platform Support
This part only concerns Allwinner platform support changes.
Though some patches still need reviewing, they feel ready to go since the MIPI CSI-2 bindings were merged, the updated CSI bindings were reviewed by Rob and the new ISP bindings as well. Although they were not merged yet, they seem ready to go at this point.
Since this multi-part series has been going on for a while, it would be great to see it merged soon!
Changes since v4:
- Removed mbus bindings patch: an equivalent change was merged;
- Added collected tags;
- Rebased on latest media tree.
Changes since v3:
- Reordered v3s mbus compatible in binding;
- Added collected tag;
- Removed rejected interconnects fix.
Changes since all-in-one v2:
- Corrected mbus index used for the interconnects;
- Used extended mbus binding and exported the DRAM clock for that;
- Reworked the description of the core openfirmware change to give more insight about the situation.
Kévin L'hôpital (1):
ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Paul Kocialkowski (5):
clk: sunxi-ng: v3s: Export MBUS and DRAM clocks to the public header
ARM: dts: sun8i: v3s: Add mbus node to represent the interconnect
ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support
ARM: dts: sun8i: v3s: Add support for the ISP
ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 ++++++++++++++++ arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++ arch/arm/boot/dts/sun8i-v3s.dtsi | 121 +++++++++++++++++++ drivers/clk/sunxi-ng/ccu-sun8i-v3s.h | 4 - include/dt-bindings/clock/sun8i-v3s-ccu.h | 4 +- 5 files changed, 251 insertions(+), 6 deletions(-)
Signature · 1 line
2.37.1
PATCH v5 1/6 clk: sunxi-ng: v3s: Export MBUS and DRAM clocks to the public header
In order to declare a mbus node for the v3s, expose its associated clocks to the public header.
--- drivers/clk/sunxi-ng/ccu-sun8i-v3s.h | 4 ---- include/dt-bindings/clock/sun8i-v3s-ccu.h | 4 ++-- 2 files changed, 2 insertions(+), 6 deletions(-)
drivers/clk/sunxi-ng/ccu-sun8i-v3s.h +0 -4
@@ -39,14 +39,10 @@/* The first bunch of module clocks are exported */ -#define CLK_DRAM 58 -/* All the DRAM gates are exported */ /* Some more module clocks are exported */ -#define CLK_MBUS 72 -/* And the GPU module clock is exported */ #define CLK_PLL_DDR1 74
include/dt-bindings/clock/sun8i-v3s-ccu.h +2 -2
@@ -87,7 +87,7 @@#define CLK_SPI0 55#define CLK_USB_PHY0 56#define CLK_USB_OHCI0 57 - +#define CLK_DRAM 58#define CLK_DRAM_VE 59#define CLK_DRAM_CSI 60#define CLK_DRAM_EHCI 61
@@ -101,7 +101,7 @@#define CLK_VE 69#define CLK_AC_DIG 70#define CLK_AVS 71 - +#define CLK_MBUS 72#define CLK_MIPI_CSI 73/* Clocks not available on V3s */
Signature · 1 line
2.37.1
PATCH v5 2/6 ARM: dts: sun8i: v3s: Add mbus node to represent the interconnect
In reply to Paul KocialkowskiThe V3s uses the mbus interconnect to provide DRAM access for a number of blocks. The SoC can only map 2 GiB of DRAM, which is reflected in the dma-ranges property.
--- arch/arm/boot/dts/sun8i-v3s.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm/boot/dts/sun8i-v3s.dtsi +15 -0
@@ -579,6 +579,21 @@ int_mii_phy: ethernet-phy@1 { }; }; + mbus: dram-controller@1c62000 { + compatible = "allwinner,sun8i-v3s-mbus"; + reg = <0x01c62000 0x1000>, + <0x01c63000 0x1000>; + reg-names = "mbus", "dram"; + clocks = <&ccu CLK_MBUS>, + <&ccu CLK_DRAM>, + <&ccu CLK_BUS_DRAM>; + clock-names = "mbus", "dram", "bus"; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x00000000 0x40000000 0x80000000>; + #interconnect-cells = <1>; + }; + spi0: spi@1c68000 { compatible = "allwinner,sun8i-h3-spi"; reg = <0x01c68000 0x1000>;
Signature · 1 line
2.37.1
PATCH v5 3/6 ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support
In reply to Paul KocialkowskiMIPI CSI-2 is supported on the V3s with an A31-based MIPI CSI-2 bridge controller. The controller uses a separate D-PHY, which is the same that is otherwise used for MIPI DSI, but used in Rx mode.
On the V3s, the CSI0 controller is dedicated to MIPI CSI-2 as it does not have access to any parallel interface pins.
Add all the necessary nodes (CSI0, MIPI CSI-2 bridge and D-PHY) to support the MIPI CSI-2 interface.
Note that a fwnode graph link is created between CSI0 and MIPI CSI-2 even when no sensor is connected. This will result in a probe failure for the controller as long as no sensor is connected but this is fine since no other interface is available.
The interconnects property is used to inherit the proper DMA offset.
--- arch/arm/boot/dts/sun8i-v3s.dtsi | 71 ++++++++++++++++++++++++++++++++ 1 file changed, 71 insertions(+)
arch/arm/boot/dts/sun8i-v3s.dtsi +71 -0
@@ -621,6 +621,77 @@ gic: interrupt-controller@1c81000 { interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + csi0: camera@1cb0000 { + compatible = "allwinner,sun8i-v3s-csi"; + reg = <0x01cb0000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI1_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CSI>; + interconnects = <&mbus 5>; + interconnect-names = "dma-mem"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + csi0_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi0>; + }; + }; + }; + }; + + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-v3s-mipi-csi2", + "allwinner,sun6i-a31-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI1_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + phys = <&dphy>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + + mipi_csi2_out_csi0: endpoint { + remote-endpoint = <&csi0_in_mipi_csi2>; + }; + }; + }; + }; + + dphy: d-phy@1cb2000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01cb2000 0x1000>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_MIPI_CSI>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_CSI>; + allwinner,direction = "rx"; + status = "disabled"; + #phy-cells = <0>; + }; + csi1: camera@1cb4000 { compatible = "allwinner,sun8i-v3s-csi"; reg = <0x01cb4000 0x3000>;
Signature · 1 line
2.37.1
PATCH v5 4/6 ARM: dts: sun8i: v3s: Add support for the ISP
In reply to Paul KocialkowskiThe V3s (and related platforms) come with an instance of the A31 ISP. Even though it is very close to the A31 ISP, it is not exactly register-compatible and a dedicated compatible only is used as a result.
Just like most other blocks of the camera pipeline, the ISP uses the common CSI bus, module and ram clock as well as reset.
A port connection to the ISP is added to CSI0 for convenience since CSI0 serves for MIPI CSI-2 interface support, which is likely to receive raw data that will need to be processed by the ISP to produce a final image.
The interconnects property is used to inherit the proper DMA offset.
--- arch/arm/boot/dts/sun8i-v3s.dtsi | 35 ++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/boot/dts/sun8i-v3s.dtsi +35 -0
@@ -645,6 +645,14 @@ csi0_in_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_out_csi0>; }; }; + + port@2 { + reg = <2>; + + csi0_out_isp: endpoint { + remote-endpoint = <&isp_in_csi0>; + }; + }; }; };
@@ -703,5 +711,32 @@ csi1: camera@1cb4000 { resets = <&ccu RST_BUS_CSI>; status = "disabled"; }; + + isp: isp@1cb8000 { + compatible = "allwinner,sun8i-v3s-isp"; + reg = <0x01cb8000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI1_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CSI>; + interconnects = <&mbus 5>; + interconnect-names = "dma-mem"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + isp_in_csi0: endpoint { + remote-endpoint = <&csi0_out_isp>; + }; + }; + }; + }; }; };
Signature · 1 line
2.37.1
PATCH v5 5/6 ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
In reply to Paul KocialkowskiMIPI CSI-2 is supported on the A83T with a dedicated controller that covers both the protocol and D-PHY. It can be connected to the CSI interface as a V4L2 subdev through the fwnode graph.
This is not done by default since connecting the bridge without a subdev attached to it will cause a failure on the CSI driver.
--- arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
arch/arm/boot/dts/sun8i-a83t.dtsi +26 -0
@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 { status = "disabled"; }; + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + }; + }; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun8i-a83t-dw-hdmi"; reg = <0x01ee0000 0x10000>;
Signature · 1 line
2.37.1
Re: [PATCH v5 5/6] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
Hi Paul,
Thank you for the patch.
Quoted 6 lines · Paul Kocialkowski
MIPI CSI-2 is supported on the A83T with a dedicated controller that covers both the protocol and D-PHY. It can be connected to the CSI interface as a V4L2 subdev through the fwnode graph.
This is not done by default since connecting the bridge without a subdev attached to it will cause a failure on the CSI driver.
No urgency, but would it be possible to fix this so that the CSI-2 receiver can be connected to the CSI unconditionally in DT ? The connection exists at the hardware level in the SoC, and should thus exist here too, regardless of whether or not a sensor is connected.
Quoted 42 lines
Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm/boot/dts/sun8i-a83t.dtsi +26
-0@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 { status = "disabled"; }; + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + }; + }; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun8i-a83t-dw-hdmi"; reg = <0x01ee0000 0x10000>;
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH v5 5/6] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
Hi Laurent,
Quoted 9 lines · Laurent Pinchart
Hi Paul,
Thank you for the patch.
Quoted 4 lines · Paul Kocialkowski
MIPI CSI-2 is supported on the A83T with a dedicated controller that covers both the protocol and D-PHY. It can be connected to the CSI interface as a V4L2 subdev through the fwnode graph.
Quoted 7 lines
Quoted 2 lines
This is not done by default since connecting the bridge without a subdev attached to it will cause a failure on the CSI driver.
No urgency, but would it be possible to fix this so that the CSI-2 receiver can be connected to the CSI unconditionally in DT ? The connection exists at the hardware level in the SoC, and should thus exist here too, regardless of whether or not a sensor is connected.
Yes it's true that having the link always would be legitimate.
For the context, this CSI controller can be switched between the MIPI CSI-2 controller and a parallel sensor input (i.e. it's not dedicated to one or the other like on the V3).
Last time I tried, having the connection between the two always there resulted in the unability to use a parallel sensor when no sensor is attached to the mipi csi-2 receiver. Probably because the async notifier never completes since the mipi csi-2's subdev is never registered without a sensor subdev attached.
Do you see a way to handle this case properly?
Thanks,
Paul
Quoted 47 lines
Quoted 42 lines
Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm/boot/dts/sun8i-a83t.dtsi +26
-0@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 { status = "disabled"; }; + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + }; + }; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun8i-a83t-dw-hdmi"; reg = <0x01ee0000 0x10000>;Signature · 3 lines
Regards, Laurent Pinchart
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
Re: [PATCH v5 5/6] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
Quoted 26 lines · Paul Kocialkowski
Hi Laurent,
Quoted 9 lines · Laurent Pinchart
Hi Paul,
Thank you for the patch.
Quoted 4 lines · Paul Kocialkowski
MIPI CSI-2 is supported on the A83T with a dedicated controller that covers both the protocol and D-PHY. It can be connected to the CSI interface as a V4L2 subdev through the fwnode graph.
Quoted 7 lines
Quoted 2 lines
This is not done by default since connecting the bridge without a subdev attached to it will cause a failure on the CSI driver.
No urgency, but would it be possible to fix this so that the CSI-2 receiver can be connected to the CSI unconditionally in DT ? The connection exists at the hardware level in the SoC, and should thus exist here too, regardless of whether or not a sensor is connected.
Yes it's true that having the link always would be legitimate.
For the context, this CSI controller can be switched between the MIPI CSI-2 controller and a parallel sensor input (i.e. it's not dedicated to one or the other like on the V3).
Quoted 6 lines
Last time I tried, having the connection between the two always there resulted in the unability to use a parallel sensor when no sensor is attached to the mipi csi-2 receiver. Probably because the async notifier never completes since the mipi csi-2's subdev is never registered without a sensor subdev attached.
Do you see a way to handle this case properly?
It sounds like an issue in the CSI-2 receiver driver. If there's no input device attached to it, it should register its subdev directly, without its own async notifier.
Quoted 42 lines
Quoted 42 lines
Quoted 42 lines
Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm/boot/dts/sun8i-a83t.dtsi +26
-0@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 { status = "disabled"; }; + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + }; + }; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun8i-a83t-dw-hdmi"; reg = <0x01ee0000 0x10000>;
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH v5 5/6] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
Hi Laurent,
Quoted 32 lines · Laurent Pinchart
Quoted 31 lines · Paul Kocialkowski
Hi Laurent,
Quoted 9 lines · Laurent Pinchart
Hi Paul,
Thank you for the patch.
Quoted 4 lines · Paul Kocialkowski
MIPI CSI-2 is supported on the A83T with a dedicated controller that covers both the protocol and D-PHY. It can be connected to the CSI interface as a V4L2 subdev through the fwnode graph.
Quoted 7 lines
Quoted 2 lines
This is not done by default since connecting the bridge without a subdev attached to it will cause a failure on the CSI driver.
No urgency, but would it be possible to fix this so that the CSI-2 receiver can be connected to the CSI unconditionally in DT ? The connection exists at the hardware level in the SoC, and should thus exist here too, regardless of whether or not a sensor is connected.
Yes it's true that having the link always would be legitimate.
For the context, this CSI controller can be switched between the MIPI CSI-2 controller and a parallel sensor input (i.e. it's not dedicated to one or the other like on the V3).
Last time I tried, having the connection between the two always there resulted in the unability to use a parallel sensor when no sensor is attached to the mipi csi-2 receiver. Probably because the async notifier never completes since the mipi csi-2's subdev is never registered without a sensor subdev attached.
Quoted 5 lines
Quoted 1 line
Do you see a way to handle this case properly?
It sounds like an issue in the CSI-2 receiver driver. If there's no input device attached to it, it should register its subdev directly, without its own async notifier.
Yes it turns out there was an error on that side, thanks for bringing it up! I have sent a fixup series which takes care of it.
Now it becomes possible to always describe the links without downsides. Well, the CSI driver will still wait for the MIPI CSI-2 bridge's subdev when its node is enabled in device-tree, but I think that is expected.
Cheers,
Paul
Quoted 47 lines
Quoted 42 lines
Quoted 42 lines
Quoted 42 lines
Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm/boot/dts/sun8i-a83t.dtsi +26
-0@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 { status = "disabled"; }; + mipi_csi2: csi@1cb1000 { + compatible = "allwinner,sun8i-a83t-mipi-csi2"; + reg = <0x01cb1000 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_MIPI_CSI>, + <&ccu CLK_CSI_MISC>; + clock-names = "bus", "mod", "mipi", "misc"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mipi_csi2_in: port@0 { + reg = <0>; + }; + + mipi_csi2_out: port@1 { + reg = <1>; + }; + }; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun8i-a83t-dw-hdmi"; reg = <0x01ee0000 0x10000>;Signature · 3 lines
Regards, Laurent Pinchart
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
PATCH v5 6/6 ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
In reply to Paul KocialkowskiFrom: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +102 -0
@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + }; + reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";
@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; }; +&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + }; + }; + }; +}; + &de { status = "okay"; };
@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>; + status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";
@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;
@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; }; +®_dldo4 { + regulator-always-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + ®_drivevbus { regulator-name = "usb0-vbus"; status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;
Signature · 1 line
2.37.1
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Hi Paul and Kévin,
Thank you for the patch.
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Quoted 27 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +13
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>;
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +10
-0+ vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };
Are those three regulators on the Banana Pi, or on the camera module ?
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;
All of this (except the status = "okay") should go to sun8i-a83t.dtsi.
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };
This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;
This looks like a candidate for upstreaming in sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.
Quoted 56 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 5 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; }; +®_dldo4 { + regulator-always-on;
Does it have to be always on ?
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";
Doesn't this belong to the base board .dts ? Same below.
Quoted 16 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +8
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus"; status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Hi Laurent,
Thansk for the review,
Quoted 7 lines · Laurent Pinchart
Hi Paul and Kévin,
Thank you for the patch.
Quoted 2 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
Quoted 8 lines
Quoted 6 lines
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdf
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 38 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 11 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; };
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins. Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 27 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 16 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +8
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;Signature · 3 lines
Regards, Laurent Pinchart
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Quoted 11 lines · Paul Kocialkowski
Quoted 10 lines · Laurent Pinchart
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
Quoted 7 lines
Quoted 1 line
I see a single sensor in this file, am I missing something ?
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/
OK. That's fine, let's just reword the commit message.
Quoted 4 lines
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
They're accepted in the upstream kernel as far as I know, a git grep for /plugin/ in .dts files produces 18 matches.
Quoted 10 lines
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdf
It's not great indeed, but not that uncommon either (unfortunately). I wonder if we need some kind of reset GPIO API, but that would be a hack at most I think.
Quoted 87 lines
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 38 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 11 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; };Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.
Quoted 5 lines
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins.
Out of curiosity, what features do those dedicated camera I2C controllers provide, compared to "normal" I2C controllers ?
Quoted 3 lines
Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
OK.
Quoted 68 lines
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Quoted 8 lines
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
That's right. I've modeled that as a parent regulator in the past, even if it doesn't reflect the exact hardware topology, it's functionally equivalent.
Quoted 28 lines
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 22 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 16 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +8
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Hi Laurent,
Quoted 14 lines · Laurent Pinchart
Quoted 13 lines · Paul Kocialkowski
Quoted 11 lines · Laurent Pinchart
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Quoted 7 lines
Quoted 5 lines
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/OK. That's fine, let's just reword the commit message.
Sure.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
They're accepted in the upstream kernel as far as I know, a git grep for /plugin/ in .dts files produces 18 matches.
Oh okay, definitely good to know thanks!
Quoted 11 lines
Quoted 10 lines
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdf
Quoted 3 lines
It's not great indeed, but not that uncommon either (unfortunately). I wonder if we need some kind of reset GPIO API, but that would be a hack at most I think.
Yeah I don't see any obvious clean solution here. But that could still be two separate dt overlays for now.
Quoted 87 lines
Quoted 87 lines
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 44 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.
Quoted 8 lines
Quoted 5 lines
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins.
Out of curiosity, what features do those dedicated camera I2C controllers provide, compared to "normal" I2C controllers ?
IIRC there's some feature to send i2c messages synced with the camera interface vsync signal, to have some kind of hardware atomic mechanism for reconfiguring a sensor.
Not sure that's very relevant for us and an implementation for it would probably just support regular I2C. We can probably achieve simialr results with the request API.
Quoted 83 lines
Quoted 3 lines
Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
OK.
Quoted 68 lines
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Quoted 8 lines
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
Quoted 3 lines
That's right. I've modeled that as a parent regulator in the past, even if it doesn't reflect the exact hardware topology, it's functionally equivalent.
Sounds good, I'll change it that way.
Cheers,
Paul
Quoted 33 lines
Quoted 28 lines
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 22 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 16 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +8
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;Signature · 3 lines
Regards, Laurent Pinchart
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Hi Laurent and Paul
Quoted 49 lines · Paul Kocialkowski
Hi Laurent,
Quoted 14 lines · Laurent Pinchart
Quoted 13 lines · Paul Kocialkowski
Quoted 11 lines · Laurent Pinchart
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Quoted 7 lines
Quoted 5 lines
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/OK. That's fine, let's just reword the commit message.
Sure.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
They're accepted in the upstream kernel as far as I know, a git grep for /plugin/ in .dts files produces 18 matches.
Oh okay, definitely good to know thanks!
Quoted 11 lines
Quoted 10 lines
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdf
Quoted 6 lines
Quoted 3 lines
It's not great indeed, but not that uncommon either (unfortunately). I wonder if we need some kind of reset GPIO API, but that would be a hack at most I think.
Yeah I don't see any obvious clean solution here. But that could still be two separate dt overlays for now.
Just to throw the idea out there, (ab)use the regulator API so that they share a regulator-gpio device that claims that GPIO. When either sensor requests the regulator, the reset line will get pulled to the appropriate state.
Dave
Quoted 235 lines
Quoted 87 lines
Quoted 87 lines
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 44 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.Quoted 8 lines
Quoted 5 lines
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins.
Out of curiosity, what features do those dedicated camera I2C controllers provide, compared to "normal" I2C controllers ?
IIRC there's some feature to send i2c messages synced with the camera interface vsync signal, to have some kind of hardware atomic mechanism for reconfiguring a sensor.
Not sure that's very relevant for us and an implementation for it would probably just support regular I2C. We can probably achieve simialr results with the request API.
Quoted 83 lines
Quoted 3 lines
Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
OK.
Quoted 68 lines
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Quoted 8 lines
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
Quoted 3 lines
That's right. I've modeled that as a parent regulator in the past, even if it doesn't reflect the exact hardware topology, it's functionally equivalent.
Sounds good, I'll change it that way.
Cheers,
Paul
Quoted 32 lines
Quoted 19 lines
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 13 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; };Quoted 9 lines
Quoted 9 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 439
Quoted 9 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;--
Regards,Quoted 1 line
Laurent Pinchart
--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Hi Dave,
Quoted 57 lines · Dave Stevenson
Hi Laurent and Paul
Quoted 53 lines · Paul Kocialkowski
Hi Laurent,
Quoted 14 lines · Laurent Pinchart
Quoted 13 lines · Paul Kocialkowski
Quoted 11 lines · Laurent Pinchart
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Quoted 7 lines
Quoted 5 lines
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/OK. That's fine, let's just reword the commit message.
Sure.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
They're accepted in the upstream kernel as far as I know, a git grep for /plugin/ in .dts files produces 18 matches.
Oh okay, definitely good to know thanks!
Quoted 14 lines
Quoted 10 lines
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdfIt's not great indeed, but not that uncommon either (unfortunately). I wonder if we need some kind of reset GPIO API, but that would be a hack at most I think.
Quoted 7 lines
Quoted 2 lines
Yeah I don't see any obvious clean solution here. But that could still be two separate dt overlays for now.
Just to throw the idea out there, (ab)use the regulator API so that they share a regulator-gpio device that claims that GPIO. When either sensor requests the regulator, the reset line will get pulled to the appropriate state.
Yeah I guess that would solve the single-gpio/multiple-users issue. But besides abusing one of the regulators for the job, that would also make it hard to respect the power sequence of the sensor.
I think I would be happier with a dedicated GPIO reset driver that consumes a single GPIO and provides as many GPIOs as needed with a behavior similar to a reset controller: go out of reset as soon as one of the provided GPIOs requests it and get back to reset as soon as all the provided GPIOs need reset.
It's a bit weird but maybe that's legit enough to make its way upstream.
Paul
Quoted 237 lines
Dave
Quoted 235 lines
Quoted 87 lines
Quoted 87 lines
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 44 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.Quoted 8 lines
Quoted 5 lines
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins.
Out of curiosity, what features do those dedicated camera I2C controllers provide, compared to "normal" I2C controllers ?
IIRC there's some feature to send i2c messages synced with the camera interface vsync signal, to have some kind of hardware atomic mechanism for reconfiguring a sensor.
Not sure that's very relevant for us and an implementation for it would probably just support regular I2C. We can probably achieve simialr results with the request API.
Quoted 83 lines
Quoted 3 lines
Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
OK.
Quoted 68 lines
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Quoted 8 lines
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
Quoted 3 lines
That's right. I've modeled that as a parent regulator in the past, even if it doesn't reflect the exact hardware topology, it's functionally equivalent.
Sounds good, I'll change it that way.
Cheers,
Paul
Quoted 32 lines
Quoted 19 lines
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 13 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; };Quoted 9 lines
Quoted 9 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 439
Quoted 9 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;--
Regards,Quoted 1 line
Laurent Pinchart
--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
Re: [PATCH NOT FOR MERGE v5 6/6] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
In reply to Paul KocialkowskiHi Paul,
Quoted 149 lines · Paul Kocialkowski
Quoted 14 lines · Laurent Pinchart
Quoted 13 lines · Paul Kocialkowski
Quoted 11 lines · Laurent Pinchart
Quoted 8 lines · Paul Kocialkowski
From: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
I see a single sensor in this file, am I missing something ?
Quoted 7 lines
Quoted 5 lines
Indeed this patch only adds the OV8865, not the OV5640 which is also present on the same camera board extension.
A patch was submitted some time ago adding support for (only) the OV5640:
https://lore.kernel.org/lkml/[email protected]/OK. That's fine, let's just reword the commit message.
Sure.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
Sounds like a perfect candidate for an overlay, it could then be merged upstream.
Do we have an upstream place to merge device-tree overlays now?
They're accepted in the upstream kernel as far as I know, a git grep for /plugin/ in .dts files produces 18 matches.
Oh okay, definitely good to know thanks!
Quoted 11 lines
Quoted 10 lines
I'll check if it's possible to describe both sensors together and actually be able to select one or the other properly from userspace. Last time I tried this wasn't possible: there's at least the shared reset GPIO used by both sensors, which cannot be requested by the two drivers in parallel.
To be honest this is very poor hardware design and it was almost certainly designed with the idea that only one sensor will be configured per boot. See https://wiki.banana-pi.org/Camera and
https://drive.google.com/file/d/0B4PAo2nW2KfnOEFTMjZ2aEVGUVU/view?usp=sharing
for the schematics pdfQuoted 3 lines
It's not great indeed, but not that uncommon either (unfortunately). I wonder if we need some kind of reset GPIO API, but that would be a hack at most I think.
Yeah I don't see any obvious clean solution here. But that could still be two separate dt overlays for now.
Quoted 87 lines
Quoted 87 lines
Quoted 31 lines
Quoted 31 lines
Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++ 1 file changed, 102 insertions(+)arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +17
-0@@ -85,6 +85,30 @@ led-1 { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd {Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts led-1 { · line 110
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +6
-0+ compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + };Are those three regulators on the Banana Pi, or on the camera module ?
That's on the camera module.
Quoted 44 lines
Quoted 7 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +1
-0+ reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";@@ -115,6 +139,23 @@ &cpu100 { cpu-supply = <®_dcdc3>; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 150
Quoted 10 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +9
-0+&csi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>;All of this (except the status = "okay") should go to
sun8i-a83t.dtsi.arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts &cpu100 { · line 154
Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ + csi_in_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_out_csi>; + };This too actually, once the issue mentioned in patch 5/6 gets fixed.
Quoted 8 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +4
-0+ }; + }; +}; + &de { status = "okay"; };arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts hdmi_out_con: endpoint { · line 193
Quoted 6 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0@@ -147,6 +188,36 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>;This looks like a candidate for upstreaming in
sun8i-a83t-bananapi-m3.dts, it shouldn't be in the overlay.Quoted 8 lines
Quoted 5 lines
I2C2 is actually also exported in the PH pins, which is available on the board header, so it's not obvious that using the PE pins should be the default.
The context is that Allwinner SoCs usually have a dedicated I2C controller for cameras, but also route a "generic" I2C controller on the same pins.
Out of curiosity, what features do those dedicated camera I2C controllers provide, compared to "normal" I2C controllers ?
Quoted 7 lines
IIRC there's some feature to send i2c messages synced with the camera interface vsync signal, to have some kind of hardware atomic mechanism for reconfiguring a sensor.
Not sure that's very relevant for us and an implementation for it would probably just support regular I2C. We can probably achieve simialr results with the request API.
This hardware feature would be very useful to improve compliance with the real-time requirements of the camera sensor. It's something that I would really like to be supported in Linux, but we'll need to design a new API for it.
Quoted 117 lines
Quoted 83 lines
Quoted 3 lines
Here that's on the PE14/15 pins. Since we don't have mainline support for this camera-dedicated I2C controller, we end up routing the generic one to the PE pins, which are routed to the camera connector.
OK.
Quoted 68 lines
In the future we could add support for this camera-dedicated controller, which would then allow routing i2c2 to the PH pins independently. This is what the downstream Allwinner BSP kernel does.
Quoted 59 lines
Quoted 59 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +45
-0+ status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <360000000>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;@@ -327,11 +416,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; };Quoted 4 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 420
Quoted 2 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +2
-0+®_dldo4 { + regulator-always-on;Does it have to be always on ?
Quoted 8 lines
Mhh so I realize the regulators handling here is quite messy. I guess I didn't do such a good review of this patch internally.
The situation is that the regulators on the camera board all have their enable pin tied to the DLDO4 output, but that would be best described as a vin-supply of the ov8865 regulators above. Their real vin supply is an always-on board-wide power source but I don't think we can represent another regulator acting as enable signal in a better way.
Quoted 3 lines
That's right. I've modeled that as a parent regulator in the past, even if it doesn't reflect the exact hardware topology, it's functionally equivalent.
Sounds good, I'll change it that way.
Quoted 28 lines
Quoted 28 lines
Now beware that the camera board schematics are confusing as they show resistors (R17, R18, R19, R20, R23) connecting some power lines together, but they are not populated on the board (I guess the point is to make a variant of the design without regulators on the camera board and to use ones from the PMU instead). This probably confused Kevin and I back when this patch was made.
Quoted 22 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts ®_dldo3 { · line 423
Quoted 3 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +3
-0+ regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi";Doesn't this belong to the base board .dts ? Same below.
Quoted 16 lines
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +8
-0+}; + ®_drivevbus { regulator-name = "usb0-vbus";AVDD-CSI status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;
Signature · 3 lines
Regards, Laurent Pinchart