New PolarFire SoC devkit devicetrees & 22.09 reference design updates
Subsystems (3)
Conor Dooley
maintainerv4 cover New PolarFire SoC devkit devicetrees & 22.09 reference design updates
Hey all,
Some 6.1 targeted changes here.
Firstly, two new dev kits (one first-party & one from Aries Embedded). They've been sitting in our vendor tree, so are being sent where they belong.
Secondly, another release of our reference design for the Icicle kit is due in September. Usually these do not really change much for the devicetree, but this time around a pair of changes impact the memory map.
The first of these is adding dma-ranges to the pcie controller. The controller had some issues to begin with & with the current reference design (v2022.05) would not work with mainline Linux nor has it since reference design v2021.08. A combination of the property, a change to the FPGA design & a small fix to the driver will get it working with mainline again. The other non-backwards compatible change to the reference design is moves of the peripherals instantiated in the fabric. Currently they are fairly spread out & a common complaint has been that this leaves little room in the fic3 section of the memory map for custom peripherals without removing the existing ones.
This series depends on [0] so as not to add dtbs_check warnings. The fabric clock support is added by [1].
Thanks,
Conor.
Changes since v3:
- add an extra patch reducing the fic3 clock rate
Changes since v2:
- drop the sd & emmc versions of the aries devicetree
- remove a extra newline
Changes since v1:
- made the polarberry part of an enum in patch 1
0 - https://lore.kernel.org/linux-gpio/[email protected]/
1 - https://lore.kernel.org/linux-clk/[email protected]/
Conor Dooley (8):
dt-bindings: riscv: microchip: document icicle reference design
dt-bindings: riscv: microchip: document the aries m100pfsevp
riscv: dts: microchip: add pci dma ranges for the icicle kit
riscv: dts: microchip: move the mpfs' pci node to -fabric.dtsi
riscv: dts: microchip: icicle: update pci address properties
riscv: dts: microchip: icicle: re-jig fabric peripheral addresses
riscv: dts: microchip: reduce the fic3 clock rate
riscv: dts: microchip: add a devicetree for aries' m100pfsevp
Shravan Chippa (1):
dt-bindings: riscv: microchip: document the sev kit
Vattipalli Praveen (1):
riscv: dts: microchip: add sevkit device tree
.../devicetree/bindings/riscv/microchip.yaml | 20 +- arch/riscv/boot/dts/microchip/Makefile | 2 + .../dts/microchip/mpfs-icicle-kit-fabric.dtsi | 44 ++++- .../boot/dts/microchip/mpfs-icicle-kit.dts | 3 +- .../dts/microchip/mpfs-m100pfs-fabric.dtsi | 45 +++++ .../boot/dts/microchip/mpfs-m100pfsevp.dts | 179 ++++++++++++++++++ .../dts/microchip/mpfs-polarberry-fabric.dtsi | 29 +++ .../dts/microchip/mpfs-sev-kit-fabric.dtsi | 45 +++++ .../riscv/boot/dts/microchip/mpfs-sev-kit.dts | 145 ++++++++++++++ arch/riscv/boot/dts/microchip/mpfs.dtsi | 29 --- 10 files changed, 499 insertions(+), 42 deletions(-) create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 1/10 dt-bindings: riscv: microchip: document icicle reference design
The icicle kit reference design's v2022.09 release,made some changes to the memory map - including adding the ability to read the fabric clock controllers via the system controller bus & making the PCI controller work with upstream Linux.
While the PCI was not working in the v2022.03 design, so nothing is broken there in terms of backwards compatibility, the fabric clocks used in the v2022.03 design were chosen by the individual run of the synthesis tool. In the v2022.09 reference design, the clocks are fixed to use the "north west" fabric Clock Conditioning Circuitry.
Make use of a new compatible to denote that this is not backwards compatible.
--- .../devicetree/bindings/riscv/microchip.yaml | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/riscv/microchip.yaml +12 -6
@@ -17,12 +17,18 @@ properties: $nodename: const: '/' compatible: - items: - - enum: - - microchip,mpfs-icicle-kit - - microchip,mpfs-icicle-reference-rtlv2203 - - sundance,polarberry - - const: microchip,mpfs + oneOf: + - items: + - enum: + - microchip,mpfs-icicle-reference-rtlv2203 + - microchip,mpfs-icicle-reference-rtlv2209 + - const: microchip,mpfs-icicle-kit + - const: microchip,mpfs + + - items: + - enum: + - sundance,polarberry + - const: microchip,mpfs additionalProperties: true
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 2/10 dt-bindings: riscv: microchip: document the aries m100pfsevp
In reply to Conor DooleyAdd a compatible for the Aries Embedded M100PFSEVP SOM + EVK platform.
--- Documentation/devicetree/bindings/riscv/microchip.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/riscv/microchip.yaml +1 -0
@@ -27,6 +27,7 @@ properties: - items: - enum: + - aries,m100pfsevp - sundance,polarberry - const: microchip,mpfs
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 3/10 dt-bindings: riscv: microchip: document the sev kit
In reply to Conor DooleyFrom: Shravan Chippa <[email protected]>
Update devicetree bindings document with PolarFire SoC Video Kit, known by its "sev-kit" product code.
--- Documentation/devicetree/bindings/riscv/microchip.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/riscv/microchip.yaml +1 -0
@@ -28,6 +28,7 @@ properties: - items: - enum: - aries,m100pfsevp + - microchip,mpfs-sev-kit - sundance,polarberry - const: microchip,mpfs
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 4/10 riscv: dts: microchip: add pci dma ranges for the icicle kit
In reply to Conor DooleyThe recently removed, accidentally included, "matr0" property was used in place of a dma-ranges property. The PCI controller is non-functional with mainline Linux in the v2022.02 or later reference designs and has not worked without configuration of address-translation since v2021.08.
Add the address translation that will be used by the v2022.09 reference design & update the compatible used by the dts.
--- arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 7 ++++++- arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts | 3 ++- 2 files changed, 8 insertions(+), 2 deletions(-)
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi +6 -1
@@ -2,7 +2,8 @@ /* Copyright (c) 2020-2021 Microchip Technology Inc */ / { - compatible = "microchip,mpfs-icicle-reference-rtlv2203", "microchip,mpfs"; + compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit", + "microchip,mpfs"; core_pwm0: pwm@41000000 { compatible = "microchip,corepwm-rtl-v4";
@@ -37,3 +38,7 @@ fabric_clk1: fabric-clk1 { clock-frequency = <125000000>; }; }; + +&pcie { + dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>; +};
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts +2 -1
@@ -11,7 +11,8 @@ / { model = "Microchip PolarFire-SoC Icicle Kit"; - compatible = "microchip,mpfs-icicle-kit", "microchip,mpfs"; + compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit", + "microchip,mpfs"; aliases { ethernet0 = &mac1;
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 5/10 riscv: dts: microchip: move the mpfs' pci node to -fabric.dtsi
In reply to Conor DooleyIn today's edition of moving things around:
The PCIe root port on PolarFire SoC is more part of the FPGA than of the Core Complex. It is located on the other side of the chip and, apart from its interrupts, most of its configuration is determined by the FPGA bitstream rather. This includes:
- address translation in both directions
- the addresses at which the config and data regions appear to the core complex
- the clocks used by the AXI bus
- the plic interrupt used
Moving the PCIe node to the -fabric.dtsi makes it clearer than a singular configuration for root port is not correct & allows the base SoC dtsi to be more easily included.
--- .../dts/microchip/mpfs-icicle-kit-fabric.dtsi | 32 +++++++++++++++++-- .../dts/microchip/mpfs-polarberry-fabric.dtsi | 29 +++++++++++++++++ arch/riscv/boot/dts/microchip/mpfs.dtsi | 29 ----------------- 3 files changed, 58 insertions(+), 32 deletions(-)
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi +29 -3
@@ -37,8 +37,34 @@ fabric_clk1: fabric-clk1 { #clock-cells = <0>; clock-frequency = <125000000>; }; -}; -&pcie { - dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>; + pcie: pcie@2000000000 { + compatible = "microchip,pcie-host-1.0"; + #address-cells = <0x3>; + #interrupt-cells = <0x1>; + #size-cells = <0x2>; + device_type = "pci"; + reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>; + reg-names = "cfg", "apb"; + bus-range = <0x0 0x7f>; + interrupt-parent = <&plic>; + interrupts = <119>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, + <0 0 0 2 &pcie_intc 1>, + <0 0 0 3 &pcie_intc 2>, + <0 0 0 4 &pcie_intc 3>; + interrupt-map-mask = <0 0 0 7>; + clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>; + clock-names = "fic0", "fic1", "fic3"; + ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>; + dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>; + msi-parent = <&pcie>; + msi-controller; + status = "disabled"; + pcie_intc: interrupt-controller { + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + }; + }; };
arch/riscv/boot/dts/microchip/mpfs-polarberry-fabric.dtsi +29 -0
@@ -13,4 +13,33 @@ fabric_clk1: fabric-clk1 { #clock-cells = <0>; clock-frequency = <125000000>; }; + + pcie: pcie@2000000000 { + compatible = "microchip,pcie-host-1.0"; + #address-cells = <0x3>; + #interrupt-cells = <0x1>; + #size-cells = <0x2>; + device_type = "pci"; + reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>; + reg-names = "cfg", "apb"; + bus-range = <0x0 0x7f>; + interrupt-parent = <&plic>; + interrupts = <119>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, + <0 0 0 2 &pcie_intc 1>, + <0 0 0 3 &pcie_intc 2>, + <0 0 0 4 &pcie_intc 3>; + interrupt-map-mask = <0 0 0 7>; + clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>; + clock-names = "fic0", "fic1", "fic3"; + ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>; + msi-parent = <&pcie>; + msi-controller; + status = "disabled"; + pcie_intc: interrupt-controller { + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + }; + }; };
arch/riscv/boot/dts/microchip/mpfs.dtsi +0 -29
@@ -464,35 +464,6 @@ usb: usb@20201000 { status = "disabled"; }; - pcie: pcie@2000000000 { - compatible = "microchip,pcie-host-1.0"; - #address-cells = <0x3>; - #interrupt-cells = <0x1>; - #size-cells = <0x2>; - device_type = "pci"; - reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>; - reg-names = "cfg", "apb"; - bus-range = <0x0 0x7f>; - interrupt-parent = <&plic>; - interrupts = <119>; - interrupt-map = <0 0 0 1 &pcie_intc 0>, - <0 0 0 2 &pcie_intc 1>, - <0 0 0 3 &pcie_intc 2>, - <0 0 0 4 &pcie_intc 3>; - interrupt-map-mask = <0 0 0 7>; - clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>; - clock-names = "fic0", "fic1", "fic3"; - ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>; - msi-parent = <&pcie>; - msi-controller; - status = "disabled"; - pcie_intc: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - mbox: mailbox@37020000 { compatible = "microchip,mpfs-mailbox"; reg = <0x0 0x37020000 0x0 0x1000>, <0x0 0x2000318C 0x0 0x40>;
Signature · 1 line
2.36.1
Conor Dooley
maintainerPATCH v4 6/10 riscv: dts: microchip: icicle: update pci address properties
In reply to Conor DooleyFor the v2022.09 reference design the PCI root port's data region has been moved to FIC1 from FIC0. This is a shorter path, allowing for higher clock rates and improved through-put. As a result, the address at which the PCIe's data region appears to the core complex has changed. The config region's address is unchanged.
As FIC0 is no longer used, its clock can be removed too.
--- .../boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi +6 -5
@@ -2,6 +2,7 @@ /* Copyright (c) 2020-2021 Microchip Technology Inc */ / { + compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit", "microchip,mpfs";
@@ -38,13 +39,13 @@ fabric_clk1: fabric-clk1 { clock-frequency = <125000000>; }; - pcie: pcie@2000000000 { + pcie: pcie@3000000000 { compatible = "microchip,pcie-host-1.0"; #address-cells = <0x3>; #interrupt-cells = <0x1>; #size-cells = <0x2>; device_type = "pci"; - reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>; + reg = <0x30 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>; reg-names = "cfg", "apb"; bus-range = <0x0 0x7f>; interrupt-parent = <&plic>;
@@ -54,9 +55,9 @@ pcie: pcie@2000000000 { <0 0 0 3 &pcie_intc 2>, <0 0 0 4 &pcie_intc 3>; interrupt-map-mask = <0 0 0 7>; - clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>; - clock-names = "fic0", "fic1", "fic3"; - ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>; + clocks = <&fabric_clk1>, <&fabric_clk3>; + clock-names = "fic1", "fic3"; + ranges = <0x3000000 0x0 0x8000000 0x30 0x8000000 0x0 0x80000000>; dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>; msi-parent = <&pcie>; msi-controller;
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v4 7/10 riscv: dts: microchip: icicle: re-jig fabric peripheral addresses
In reply to Conor DooleyWhen users try to add onto the reference design, they find that the current addresses that peripherals connected to Fabric InterConnect (FIC) 3 use are restrictive. For the v2022.09 reference design, the peripherals have been shifted down, leaving more contiguous address space for their custom IP/peripherals.
--- arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi +4 -4
@@ -6,18 +6,18 @@ / { compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit", "microchip,mpfs"; - core_pwm0: pwm@41000000 { + core_pwm0: pwm@40000000 { compatible = "microchip,corepwm-rtl-v4"; - reg = <0x0 0x41000000 0x0 0xF0>; + reg = <0x0 0x40000000 0x0 0xF0>; microchip,sync-update-mask = /bits/ 32 <0>; #pwm-cells = <2>; clocks = <&fabric_clk3>; status = "disabled"; }; - i2c2: i2c@44000000 { + i2c2: i2c@40000200 { compatible = "microchip,corei2c-rtl-v7"; - reg = <0x0 0x44000000 0x0 0x1000>; + reg = <0x0 0x40000200 0x0 0x1000>; #address-cells = <1>; #size-cells = <0>; clocks = <&fabric_clk3>;
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v4 8/10 riscv: dts: microchip: reduce the fic3 clock rate
In reply to Conor DooleyFor the v2022.09 release of the reference design, the fic3 clock rate been reduced from 62.5 MHz to 50 MHz as it allows timing to be closed significantly more quickly by customers who chose to build the reference design themselves.
--- arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi +1 -1
@@ -30,7 +30,7 @@ i2c2: i2c@40000200 { fabric_clk3: fabric-clk3 { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <62500000>; + clock-frequency = <50000000>; }; fabric_clk1: fabric-clk1 {
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v4 9/10 riscv: dts: microchip: add sevkit device tree
In reply to Conor DooleyFrom: Vattipalli Praveen <[email protected]>
Add a basic dts for the Microchip Smart Embedded Vision dev kit. The SEV kit is an upcoming first party board, featuring an MPFS250T and:
- Dual Sony Camera Sensors (IMX334)
- IEEE 802.11 b/g/n 20MHz (1x1) Wi-Fi
- Bluetooth 5 Low Energy
- 4 GB DDR4 x64
- 2 GB LPDDR4 x32
- 1 GB SPI Flash
- 8 GB eMMC flash & SD card slot (multiplexed)
- HDMI2.0 Video Input/Output
- MIPI DSI Output
- MIPI CSI-2 Input
--- arch/riscv/boot/dts/microchip/Makefile | 1 + .../dts/microchip/mpfs-sev-kit-fabric.dtsi | 45 ++++++ .../riscv/boot/dts/microchip/mpfs-sev-kit.dts | 145 ++++++++++++++++++ 3 files changed, 191 insertions(+) create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
arch/riscv/boot/dts/microchip/Makefile +1 -0
@@ -1,4 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi new file +45 -0
45 lines not on this page · raw message
arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts new file +145 -0
145 lines not on this page · raw message
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Conor Dooley
maintainerPATCH v4 10/10 riscv: dts: microchip: add a devicetree for aries' m100pfsevp
In reply to Conor DooleyAdd device trees for both configs used by the Aries Embedded M100PFSEVP. The M100OFSEVP consists of a MPFS250T on a SOM, featuring:
- 2GB DDR4 SDRAM dedicated to the HMS
- 512MB DDR4 SDRAM dedicated to the FPGA
- 32 MB SPI NOR Flash
- 4 GByte eMMC
and a carrier board with:
- 2x Gigabit Ethernet
- USB
- 2x UART
- 2x CAN
- TFT connector
- HSMC extension connector
- 3x PMOD extension connectors
- microSD-card slot
--- arch/riscv/boot/dts/microchip/Makefile | 1 + .../dts/microchip/mpfs-m100pfs-fabric.dtsi | 45 +++++ .../boot/dts/microchip/mpfs-m100pfsevp.dts | 179 ++++++++++++++++++ 3 files changed, 225 insertions(+) create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts
arch/riscv/boot/dts/microchip/Makefile +1 -0
@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-m100pfsevp.dtb dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi new file +45 -0
45 lines not on this page · raw message
arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +179 -0
179 lines not on this page · raw message
Signature · 7 lines
2.36.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
A message that is not in the archive (sent off-list or not yet received): CO6PR11MB5604046550E3D74CBBC8E94681409@CO6PR11MB5604.namprd11.prod.outlook.com
[email protected]
maintainerRe: [PATCH v4 10/10] riscv: dts: microchip: add a devicetree for aries' m100pfsevp
Hey Shravan,
Please don't drop the lists etc from CC.
On 08/09/2022 12:29, shravan Chippa - I35088 wrote:>
Quoted 154 lines
Quoted 110 lines
-----Original Message-----
From: Conor Dooley <[email protected]>
Sent: 08 September 2022 04:47 PM
To: Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley - M52691 <[email protected]>; Daire McNamara - X61553 <[email protected]>; shravan Chippa - I35088 <[email protected]>
Cc: Paul Walmsley <[email protected]>; Palmer Dabbelt <[email protected]>; Albert Ou <[email protected]>; Cyril Jean - M31571 <[email protected]>; Lewis Hanly - M34782 <[email protected]>; Praveen Kumar - I30718 <[email protected]>; Wolfgang Grandegger <wg@aries- embedded.de>; Hugh Breslin - M31864 <[email protected]>; [email protected]; [email protected]; linux- [email protected]
Subject: [PATCH v4 10/10] riscv: dts: microchip: add a devicetree for aries' m100pfsevpAdd device trees for both configs used by the Aries Embedded M100PFSEVP. The M100OFSEVP consists of a MPFS250T on a SOM,
featuring:
- 2GB DDR4 SDRAM dedicated to the HMS
- 512MB DDR4 SDRAM dedicated to the FPGA
- 32 MB SPI NOR Flash
- 4 GByte eMMCand a carrier board with:
- 2x Gigabit Ethernet
- USB
- 2x UART
- 2x CAN
- TFT connector
- HSMC extension connector
- 3x PMOD extension connectors
- microSD-card slotm100pfs-som-mpfs025t-pcie-serdes
microchip-soc-fpga-m100pfsevp-riscv-hsmc-pmod
embedded.de/products/M100PFS/Hardware/M100PFSEVP-Schematics.pdf
Co-developed-by Wolfgang Grandegger <[email protected]>Signed-off-by Wolfgang Grandegger <[email protected]>Signed-off-by Conor Dooley <[email protected]>arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +4
-0@@ -0,0 +1,179 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Original all-in-one devicetree: + * Copyright (C) 2021-2022 - Wolfgang Grandegger <wg@aries-embedded.de>
+ * Rewritten to use includes:
+ * Copyright (C) 2022 - Conor Dooley <[email protected]> */arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +49
-0+/dts-v1/; + +#include "mpfs.dtsi" +#include "mpfs-m100pfs-fabric.dtsi" + +/* Clock frequency (in Hz) of the rtcclk */ +#define MTIMER_FREQ 1000000 + +/ { + model = "Aries Embedded M100PFEVPS"; + compatible = "aries,m100pfsevp", "microchip,mpfs"; + + aliases { + ethernet0 = &mac0; + ethernet1 = &mac1; + serial0 = &mmuart0; + serial1 = &mmuart1; + serial2 = &mmuart2; + serial3 = &mmuart3; + serial4 = &mmuart4; + gpio0 = &gpio0; + gpio1 = &gpio2; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; + + cpus { + timebase-frequency = <MTIMER_FREQ>; + }; + + ddrc_cache_lo: memory@80000000 { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x40000000>; + }; + ddrc_cache_hi: memory@1040000000 { + device_type = "memory"; + reg = <0x10 0x40000000 0x0 0x40000000>; + }; +}; + +&can0 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; +};arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts line 66
Quoted 10 lines
arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +10
-0+ +&i2c1 { + status = "okay"; +}; + +&gpio0 { + interrupts = <13>, <14>, <15>, <16>, + <17>, <18>, <19>, <20>, + <21>, <22>, <23>, <24>, + <25>, <26>;Commented bellow...
Quoted 18 lines
arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +18
-0+ ngpios = <14>; + status = "okay"; + + pmic-irq-hog { + gpio-hog; + gpios = <13 0>; + input; + }; + + /* Set to low for eMMC, high for SD-card */ + mmc-sel-hog { + gpio-hog; + gpios = <12 0>; + output-high; + }; +}; + +&gpio2 {arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts line 94
Quoted 10 lines
arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +10
-0+ interrupts = <13>, <14>, <15>, <16>, + <17>, <18>, <19>, <20>, + <21>, <22>, <23>, <24>, + <25>, <26>, <27>, <28>, + <29>, <30>, <31>, <32>, + <33>, <34>, <35>, <36>, + <37>, <38>, <39>, <40>, + <41>, <42>, <43>, <44>; + status = "okay"; +};Same interrupt numbers GPIO2 and GPIO0?
Quoted 3 lines
As per my understanding, GPIO2 and GPIO0 are using maxed interrupt lines Only one bank GPIO0/GPIO2 can work in direct interrupt mode other should be in non-direct interrupt mode.
Yeah, good spot - this cannot be correct. I had a look in the HSS and there does not appear to be anything setting the GPIO_INTERRUPT_FAB_CR for the m100pfsevp target & therefore would be at its default value of 0 - so GPIO2 should be using interrupt 53 for all GPIOs.
Thanks,
Conor.
Quoted 88 lines
Quoted 87 lines
arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts new file +85
-1+ +&mac0 { + status = "okay"; + phy-mode = "gmii"; + phy-handle = <&phy0>; + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&mac1 { + status = "okay"; + phy-mode = "gmii"; + phy-handle = <&phy1>; + phy1: ethernet-phy@0 { + reg = <0>; + }; +}; + +&mbox { + status = "okay"; +}; + +&mmc { + max-frequency = <50000000>; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + no-1-8-v; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; + disable-wp; + status = "okay"; +}; + +&mmuart1 { + status = "okay"; +}; + +&mmuart2 { + status = "okay"; +}; + +&mmuart3 { + status = "okay"; +}; + +&mmuart4 { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&qspi { + status = "okay"; +}; + +&refclk { + clock-frequency = <125000000>; +}; + +&rtc { + status = "okay"; +}; + +&spi0 { + status = "okay"; +}; + +&spi1 { + status = "okay"; +}; + +&syscontroller { + status = "okay"; +}; + +&usb { + status = "okay"; + dr_mode = "host"; +}; --2.36.1