Add support for TI TPS65219 PMIC.
Subsystems (6)
v5 cover Add support for TI TPS65219 PMIC.
Hi everyone,
Sending again v5 changing deprecated mail for Lee Jones.
bindings and regulator are already there as it is based on the regulator tree branch for-6.1:
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
Changes in v5:
- Remove pm_power_off functionality as it is unused in ARM64 systems
- Change mfd subject to prefixes matching subsystem
Validation:
regulator: tps65219: Fix .bypass_val_on setting
reported by Axel Lin has been validated on board.
Regards,
Jerome
Previous versions:
v4 - https://lore.kernel.org/lkml/[email protected]/
v3 - https://lore.kernel.org/lkml/[email protected]/
v2 - https://lore.kernel.org/lkml/[email protected]/
v1 - https://lore.kernel.org/lkml/[email protected]/
Jerome Neanne (5):
DONOTMERGE: arm64: dts: ti: Add TI TPS65219 PMIC support for AM642 SK
board.
DONOTMERGE: arm64: dts: ti: Add pinmux and irq mapping for TPS65219
external interrupts
DONOTMERGE: arm64: dts: ti: k3-am642-sk: Enable tps65219 power-button
mfd: tps65219: Add driver for TI TPS65219 PMIC
arm64: defconfig: Add tps65219 as modules
Markus Schneider-Pargmann (1):
Input: Add tps65219 interrupt driven powerbutton
MAINTAINERS | 1 + arch/arm64/boot/dts/ti/k3-am642-sk.dts | 115 ++++++++ arch/arm64/configs/defconfig | 3 + drivers/input/misc/Kconfig | 10 + drivers/input/misc/Makefile | 1 + drivers/input/misc/tps65219-pwrbutton.c | 149 ++++++++++ drivers/mfd/Kconfig | 14 + drivers/mfd/Makefile | 1 + drivers/mfd/tps65219.c | 320 ++++++++++++++++++++++ include/linux/mfd/tps65219.h | 345 ++++++++++++++++++++++++ 10 files changed, 959 insertions(+) create mode 100644 drivers/input/misc/tps65219-pwrbutton.c create mode 100644 drivers/mfd/tps65219.c create mode 100644 include/linux/mfd/tps65219.h
Signature · 1 line
2.17.1
PATCH v5 1/6 DONOTMERGE: arm64: dts: ti: Add TI TPS65219 PMIC support for AM642 SK board.
Add support fot the TI Power Management IC TPS65219 on the AM642 SKEVM board.
Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.
--- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 104 +++++++++++++++++++++++++ 1 file changed, 104 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +104 -0
@@ -150,6 +150,20 @@ vin-supply = <&com8_ls_en>; gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>; }; + + vsel_sd_nddr: gpio-regulator { + compatible = "regulator-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&vsel_sd_nddr_pins_default>; + regulator-name = "tps65219-LDO1-SEL-SD"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + vin-supply = <&ldo1_reg>; + gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0>, + <3300000 0x1>; + }; }; &main_pmx0 {
@@ -181,6 +195,13 @@ >; }; + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
@@ -267,6 +288,12 @@ AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */ >; }; + + vsel_sd_nddr_pins_default: vsel-sd-nddr-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */ + >; + }; }; &mcu_uart0 {
@@ -315,6 +342,83 @@ status = "disabled"; }; +&main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + status = "okay"; + + tps65219: pmic@30 { + compatible = "ti,tps65219"; + reg = <0x30>; + system-power-controller; + + buck1-supply = <&vcc_3v3_sys>; + buck2-supply = <&vcc_3v3_sys>; + buck3-supply = <&vcc_3v3_sys>; + ldo1-supply = <&vcc_3v3_sys>; + ldo2-supply = <&buck2_reg>; + ldo3-supply = <&vcc_3v3_sys>; + ldo4-supply = <&vcc_3v3_sys>; + + regulators { + buck1_reg: buck1 { + regulator-name = "VDD_CORE"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + }; + + buck2_reg: buck2 { + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + buck3_reg: buck3 { + regulator-name = "VDD_LPDDR4"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-name = "VDDSHV_SD_IO_PMIC"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-allow-bypass; + }; + + ldo2_reg: ldo2 { + regulator-name = "VDDAR_CORE"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: ldo4 { + regulator-name = "VDD_PHY_2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; &main_i2c1 { pinctrl-names = "default"; pinctrl-0 = <&main_i2c1_pins_default>;
Signature · 1 line
2.17.1
PATCH v5 2/6 DONOTMERGE: arm64: dts: ti: Add pinmux and irq mapping for TPS65219 external interrupts
In reply to Jerome NeanneInterrupt occurring on PMIC TPS65219 is propagated to SOC through EXTINTn pin connected to gic500 interrupt controller
Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.
--- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +10 -0
@@ -294,6 +294,12 @@ AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */ >; }; + + pmic_irq_pins_default: pmic-irq-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0278, PIN_INPUT, 0) /* (C19) EXTINTn */ + >; + }; }; &mcu_uart0 {
@@ -352,6 +358,10 @@ compatible = "ti,tps65219"; reg = <0x30>; system-power-controller; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_irq_pins_default>; + interrupt-parent = <&gic500>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; buck1-supply = <&vcc_3v3_sys>; buck2-supply = <&vcc_3v3_sys>;
Signature · 1 line
2.17.1
PATCH v5 3/6 DONOTMERGE: arm64: dts: ti: k3-am642-sk: Enable tps65219 power-button
In reply to Jerome NeanneThis board uses the pin as a power-button, enable it.
Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.
--- arch/arm64/boot/dts/ti/k3-am642-sk.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -0
@@ -362,6 +362,7 @@ pinctrl-0 = <&pmic_irq_pins_default>; interrupt-parent = <&gic500>; interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + ti,power-button; buck1-supply = <&vcc_3v3_sys>; buck2-supply = <&vcc_3v3_sys>;
Signature · 1 line
2.17.1
PATCH v5 4/6 mfd: tps65219: Add driver for TI TPS65219 PMIC
In reply to Jerome NeanneThe TPS65219 is a power management IC PMIC designed to supply a wide range of SoCs in both portable and stationary applications. Any SoC can control TPS65219 over a standard I2C interface.
It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
- GPIOs
- Multi Function Pins (MFP)
- power-button
This patch adds support for tps65219 PMIC. At this time only the functionalities listed below are made available:
- Regulators probe and functionalities
- warm and cold reset support
- SW shutdown support
- Regulator warnings via IRQs
- Power-button via IRQ
--- MAINTAINERS | 1 + drivers/mfd/Kconfig | 14 ++ drivers/mfd/Makefile | 1 + drivers/mfd/tps65219.c | 320 ++++++++++++++++++++++++++++++++ include/linux/mfd/tps65219.h | 345 +++++++++++++++++++++++++++++++++++ 5 files changed, 681 insertions(+) create mode 100644 drivers/mfd/tps65219.c create mode 100644 include/linux/mfd/tps65219.h
MAINTAINERS +1 -0
@@ -14926,6 +14926,7 @@ F: drivers/mfd/menelaus.c F: drivers/mfd/palmas.c F: drivers/mfd/tps65217.c F: drivers/mfd/tps65218.c +F: drivers/mfd/tps65219.c F: drivers/mfd/tps65910.c F: drivers/mfd/twl-core.[ch] F: drivers/mfd/twl4030*.c
drivers/mfd/Kconfig +14 -0
@@ -1576,6 +1576,20 @@ config MFD_TPS65218 This driver can also be built as a module. If so, the module will be called tps65218. +config MFD_TPS65219 + tristate "TI TPS65219 Power Management IC" + depends on I2C && OF + select MFD_CORE + select REGMAP_I2C + select REGMAP_IRQ + help + If you say yes here you get support for the TPS65219 series of Power + Management ICs. These include voltage regulators, GPIOs and + push/power button that are often used in portable devices. + + This driver can also be built as a module. If so, the module + will be called tps65219. + config MFD_TPS6586X bool "TI TPS6586x Power Management chips" depends on I2C=y
drivers/mfd/Makefile +1 -0
@@ -101,6 +101,7 @@ obj-$(CONFIG_TPS6507X) += tps6507x.o obj-$(CONFIG_MFD_TPS65086) += tps65086.o obj-$(CONFIG_MFD_TPS65217) += tps65217.o obj-$(CONFIG_MFD_TPS65218) += tps65218.o +obj-$(CONFIG_MFD_TPS65219) += tps65219.o obj-$(CONFIG_MFD_TPS65910) += tps65910.o obj-$(CONFIG_MFD_TPS65912) += tps65912-core.o obj-$(CONFIG_MFD_TPS65912_I2C) += tps65912-i2c.o
drivers/mfd/tps65219.c new file +320 -0
320 lines not on this page · raw message
include/linux/mfd/tps65219.h new file +345 -0
345 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v5 5/6 Input: Add tps65219 interrupt driven powerbutton
In reply to Jerome NeanneFrom: Markus Schneider-Pargmann <[email protected]>
TPS65219 has different interrupts compared to other TPS6521* chips. TPS65219 defines two interrupts for the powerbutton one for push and one for release.
This driver is very simple in that it maps the push interrupt to a key input and the release interrupt to a key release.
--- drivers/input/misc/Kconfig | 10 ++ drivers/input/misc/Makefile | 1 + drivers/input/misc/tps65219-pwrbutton.c | 149 ++++++++++++++++++++++++ 3 files changed, 160 insertions(+) create mode 100644 drivers/input/misc/tps65219-pwrbutton.c
drivers/input/misc/Kconfig +10 -0
@@ -468,6 +468,16 @@ config INPUT_TPS65218_PWRBUTTON To compile this driver as a module, choose M here. The module will be called tps65218-pwrbutton. +config INPUT_TPS65219_PWRBUTTON + tristate "TPS65219 Power button driver" + depends on MFD_TPS65219 + help + Say Y here if you want to enable power button reporting for + TPS65219 Power Management IC devices. + + To compile this driver as a module, choose M here. The module will + be called tps65219-pwrbutton. + config INPUT_AXP20X_PEK tristate "X-Powers AXP20X power button driver" depends on MFD_AXP20X
drivers/input/misc/Makefile +1 -0
@@ -78,6 +78,7 @@ obj-$(CONFIG_INPUT_SOC_BUTTON_ARRAY) += soc_button_array.o obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_STPMIC1_ONKEY) += stpmic1_onkey.o obj-$(CONFIG_INPUT_TPS65218_PWRBUTTON) += tps65218-pwrbutton.o +obj-$(CONFIG_INPUT_TPS65219_PWRBUTTON) += tps65219-pwrbutton.o obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o obj-$(CONFIG_INPUT_TWL4030_VIBRA) += twl4030-vibra.o obj-$(CONFIG_INPUT_TWL6040_VIBRA) += twl6040-vibra.o
drivers/input/misc/tps65219-pwrbutton.c new file +149 -0
149 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v5 5/6] Input: Add tps65219 interrupt driven powerbutton
Hi Jerome,
Quoted 13 lines · Jerome Neanne
drivers/input/misc/tps65219-pwrbutton.c new file +13
-0+static int tps65219_pb_probe (struct platform_device *pdev) +{ +struct tps65219 *tps =dev_get_drvdata (pdev->dev.parent); +struct device *dev = &pdev->dev; +struct tps65219_pwrbutton *pwr; +struct input_dev *idev; +int error; +int push_irq; +int release_irq; + + pwr =devm_kzalloc (dev,sizeof (*pwr),GFP_KERNEL ); +if (!pwr) +return -ENOMEM ;
drivers/input/misc/tps65219-pwrbutton.c line 67
Quoted 10 lines
drivers/input/misc/tps65219-pwrbutton.c new file +10
-0+ + idev =devm_input_allocate_device (dev); +if (!idev) +return -ENOMEM ; + + idev->name = pdev->name; +snprintf (pwr->phys,sizeof (pwr->phys),"%s/input0" , + pdev->name); + idev->phys = pwr->phys; + idev->dev.parent = dev;
As I mentioned in my previous email, this assignment is not needed given that devm_input_allocate_device() is used. Otherwise:
Please feel free to merge through MFD tree.
Thanks.
Signature · 1 line
Dmitry
PATCH v5 6/6 arm64: defconfig: Add tps65219 as modules
In reply to Jerome NeanneThis adds defconfig option to support TPS65219 PMIC, MFD, Regulators and power-button.
--- arch/arm64/configs/defconfig | 3 +++ 1 file changed, 3 insertions(+)
arch/arm64/configs/defconfig +3 -0
@@ -406,6 +406,7 @@ CONFIG_TOUCHSCREEN_GOODIX=m CONFIG_TOUCHSCREEN_EDT_FT5X06=m CONFIG_INPUT_MISC=y CONFIG_INPUT_PM8941_PWRKEY=y +CONFIG_INPUT_TPS65219_PWRBUTTON=m CONFIG_INPUT_PM8XXX_VIBRATOR=m CONFIG_INPUT_PWM_BEEPER=m CONFIG_INPUT_PWM_VIBRA=m
@@ -639,6 +640,7 @@ CONFIG_MFD_SPMI_PMIC=y CONFIG_MFD_RK808=y CONFIG_MFD_SEC_CORE=y CONFIG_MFD_SL28CPLD=y +CONFIG_MFD_TPS65219=m CONFIG_MFD_ROHM_BD718XX=y CONFIG_MFD_WCD934X=m CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -666,6 +668,7 @@ CONFIG_REGULATOR_QCOM_SPMI=y CONFIG_REGULATOR_RK808=y CONFIG_REGULATOR_S2MPS11=y CONFIG_REGULATOR_TPS65132=m +CONFIG_REGULATOR_TPS65219=m CONFIG_REGULATOR_VCTRL=m CONFIG_RC_CORE=m CONFIG_RC_DECODERS=y
Signature · 1 line
2.17.1