Skip to contentSkip to conversation

net: mv643xx_eth: support MII/GMII/RGMII modes

PATCH Superseded David Yang 4 participants 10 messages Sep 30, 2022 – Oct 4, 2022

Subsystems (3)

v1 of 6 Superseded Latest is v6 →

lore
Share & tools
lore

David Yang

author
#0 lore raw

PATCH 1/1 net: mv643xx_eth: support MII/GMII/RGMII modes

On device reset all ports are automatically set to RGMII mode. MII mode must be explicitly enabled.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
 drivers/net/ethernet/marvell/mv643xx_eth.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/net/ethernet/marvell/mv643xx_eth.c +16 -0
index b6be0552a..e2216ce5e 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -1245,6 +1246,21 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
 	wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+	/* If two Ethernet controllers present in the SoC, MII modes follow the
+	 * following matrix:
+	 *
+	 * Port0 Mode	Port1 Mode	Port0 RGMII_EN	Port1 RGMII_EN
+	 * RGMII	RGMII		1		1
+	 * RGMII	MII/MMII	1		0
+	 * MII/MMII	RGMII		0		1
+	 * GMII		N/A		0		0
+	 *
+	 * To enable GMII on Port 0, Port 1 must also disable RGMII_EN too.
+	 */
+	if (!phy_interface_is_rgmii(dev->phydev))
+		wrlp(mp, PORT_SERIAL_CONTROL1,
+		     rdlp(mp, PORT_SERIAL_CONTROL1) & ~RGMII_EN);
 }
 
 /* statistics ***************************************************************/
Signature · 1 line
2.35.1
#1 lore raw
Quoted 35 lines · David Yang

On device reset all ports are automatically set to RGMII mode. MII mode must be explicitly enabled.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
 drivers/net/ethernet/marvell/mv643xx_eth.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/net/ethernet/marvell/mv643xx_eth.c +6 -0
index b6be0552a..e2216ce5e 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -1245,6 +1246,21 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
 	wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+	/* If two Ethernet controllers present in the SoC, MII modes follow the
+	 * following matrix:
+	 *
+	 * Port0 Mode	Port1 Mode	Port0 RGMII_EN	Port1 RGMII_EN

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1263

Quoted 10 lines
drivers/net/ethernet/marvell/mv643xx_eth.c +10 -0
+	 * RGMII	RGMII		1		1
+	 * RGMII	MII/MMII	1		0
+	 * MII/MMII	RGMII		0		1
+	 * GMII		N/A		0		0
+	 *
+	 * To enable GMII on Port 0, Port 1 must also disable RGMII_EN too.
+	 */
+	if (!phy_interface_is_rgmii(dev->phydev))
+		wrlp(mp, PORT_SERIAL_CONTROL1,
+		     rdlp(mp, PORT_SERIAL_CONTROL1) & ~RGMII_EN);

I could be reading this wrong, but doesn't this break the third line:

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1256

Quoted 1 line
drivers/net/ethernet/marvell/mv643xx_eth.c +1 -0
+	 * MII/MMII	RGMII		0		1

Port 1 probes first, phy_interface is rgmii, so nothing happens, port1 RGMII_EN is left true.

Port 0 then probes, MII/MMII is not RGMII, so port1 RGMII_EN is cleared, breaking port1.

I think you need to be more specific with the comparison.

Andrew

author
#2 lore raw

PATCH v2 1/1 net: mv643xx_eth: support MII/GMII/RGMII modes

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
v2: clarify modes work on controllers, read default value from PSC1

 drivers/net/ethernet/marvell/mv643xx_eth.c | 36 ++++++++++++++++++++--
 1 file changed, 33 insertions(+), 3 deletions(-)
drivers/net/ethernet/marvell/mv643xx_eth.c +33 -3
index b6be0552a..ddaccc979 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -1215,6 +1216,7 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 	             DISABLE_AUTO_NEG_SPEED_GMII |
 		     DISABLE_AUTO_NEG_FOR_FLOW_CTRL |
 		     DISABLE_AUTO_NEG_FOR_DUPLEX;
+	u32 psc1r = rdlp(mp, PORT_SERIAL_CONTROL1);
 
 	if (dev->phydev->autoneg == AUTONEG_ENABLE) {
 		/* enable auto negotiation */
@@ -1245,6 +1247,30 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
 	wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+	/* If two Ethernet controllers present in the SoC, and both of them have
+	 * RGMII_EN disabled, the first controller will be in GMII mode and the
+	 * second one is effectively disabled, instead of two MII interfaces.
+	 *
+	 * To enable GMII in the first controller, the second one must also be
+	 * configured (and may be enabled) with RGMII_EN disabled too, even
+	 * though it cannot be used at all.
+	 */
+	switch (dev->phydev->interface) {
+	case PHY_INTERFACE_MODE_MII:
+	case PHY_INTERFACE_MODE_GMII:
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r & ~RGMII_EN);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r | RGMII_EN);
+		break;
+	default:
+		/* Unknown; don't touch */
+		break;
+	}
 }
 
 /* statistics ***************************************************************/
@@ -2975,11 +3001,15 @@ static int get_phy_mode(struct mv643xx_eth_private *mp)
 	if (dev->of_node)
 		err = of_get_phy_mode(dev->of_node, &iface);
 
-	/* Historical default if unspecified. We could also read/write
-	 * the interface state in the PSC1
+	/* Read the interface state in the PSC1.
+	 *
+	 * Modes of two devices may interact; see comments in
+	 * mv643xx_eth_adjust_link. Currently there is no way to detect another
+	 * device within this scope; blindly set MII here.
 	 */
 	if (!dev->of_node || err)
-		iface = PHY_INTERFACE_MODE_GMII;
+		iface = rdlp(mp, PORT_SERIAL_CONTROL1) & RGMII_EN ?
+			PHY_INTERFACE_MODE_RGMII : PHY_INTERFACE_MODE_MII;
 	return iface;
 }
 
Signature · 1 line
2.35.1
maintainer
#3 lore raw

Hello,

Quoted 9 lines · David Yang

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

It looks like that despite the subj change, this is superseded by:

https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

I'm updating the PW accordingly. Please let me know if you intended otherwise.

Thanks,

Paolo

author
#4 lore raw
In reply to Andrew Lunn
Quoted 55 lines · Andrew Lunn <[email protected]> 于2022年10月1日周六 04:28写道:
Quoted 35 lines · David Yang

On device reset all ports are automatically set to RGMII mode. MII mode must be explicitly enabled.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
 drivers/net/ethernet/marvell/mv643xx_eth.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/net/ethernet/marvell/mv643xx_eth.c +6 -0
index b6be0552a..e2216ce5e 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND                  0x0048
 #define TXQ_FIX_PRIO_CONF            0x004c
 #define PORT_SERIAL_CONTROL1         0x004c
+#define  RGMII_EN                    0x00000008
 #define  CLK125_BYPASS_EN            0x00000010
 #define TX_BW_RATE                   0x0050
 #define TX_BW_MTU                    0x0058
@@ -1245,6 +1246,21 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
      wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+     /* If two Ethernet controllers present in the SoC, MII modes follow the
+      * following matrix:
+      *
+      * Port0 Mode   Port1 Mode      Port0 RGMII_EN  Port1 RGMII_EN

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1263

Quoted 10 lines
drivers/net/ethernet/marvell/mv643xx_eth.c +10 -0
+      * RGMII        RGMII           1               1
+      * RGMII        MII/MMII        1               0
+      * MII/MMII     RGMII           0               1
+      * GMII         N/A             0               0
+      *
+      * To enable GMII on Port 0, Port 1 must also disable RGMII_EN too.
+      */
+     if (!phy_interface_is_rgmii(dev->phydev))
+             wrlp(mp, PORT_SERIAL_CONTROL1,
+                  rdlp(mp, PORT_SERIAL_CONTROL1) & ~RGMII_EN);

I could be reading this wrong, but doesn't this break the third line:

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1256

Quoted 1 line
drivers/net/ethernet/marvell/mv643xx_eth.c +1 -0
+      * MII/MMII     RGMII           0               1

Port 1 probes first, phy_interface is rgmii, so nothing happens, port1 RGMII_EN is left true.

Quoted 6 lines

Port 0 then probes, MII/MMII is not RGMII, so port1 RGMII_EN is cleared, breaking port1.

I think you need to be more specific with the comparison.

Andrew

Oh, I see. So you mean "phy-mode" property should belong to controller, not port? I thought one controller can have at most one port.

#5 lore raw
Quoted 59 lines · Yangfl
Quoted 58 lines · Andrew Lunn <[email protected]> 于2022年10月1日周六 04:28写道:
Quoted 35 lines · David Yang

On device reset all ports are automatically set to RGMII mode. MII mode must be explicitly enabled.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
 drivers/net/ethernet/marvell/mv643xx_eth.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/net/ethernet/marvell/mv643xx_eth.c +6 -0
index b6be0552a..e2216ce5e 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND                  0x0048
 #define TXQ_FIX_PRIO_CONF            0x004c
 #define PORT_SERIAL_CONTROL1         0x004c
+#define  RGMII_EN                    0x00000008
 #define  CLK125_BYPASS_EN            0x00000010
 #define TX_BW_RATE                   0x0050
 #define TX_BW_MTU                    0x0058
@@ -1245,6 +1246,21 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
      wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+     /* If two Ethernet controllers present in the SoC, MII modes follow the
+      * following matrix:
+      *
+      * Port0 Mode   Port1 Mode      Port0 RGMII_EN  Port1 RGMII_EN

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1263

Quoted 10 lines
drivers/net/ethernet/marvell/mv643xx_eth.c +10 -0
+      * RGMII        RGMII           1               1
+      * RGMII        MII/MMII        1               0
+      * MII/MMII     RGMII           0               1
+      * GMII         N/A             0               0
+      *
+      * To enable GMII on Port 0, Port 1 must also disable RGMII_EN too.
+      */
+     if (!phy_interface_is_rgmii(dev->phydev))
+             wrlp(mp, PORT_SERIAL_CONTROL1,
+                  rdlp(mp, PORT_SERIAL_CONTROL1) & ~RGMII_EN);

I could be reading this wrong, but doesn't this break the third line:

drivers/net/ethernet/marvell/mv643xx_eth.c static void mv643xx_eth_adjust_link(struct net_device *dev) · line 1256

Quoted 1 line
drivers/net/ethernet/marvell/mv643xx_eth.c +1 -0
+      * MII/MMII     RGMII           0               1

Port 1 probes first, phy_interface is rgmii, so nothing happens, port1 RGMII_EN is left true.

Port 0 then probes, MII/MMII is not RGMII, so port1 RGMII_EN is cleared, breaking port1.

Quoted 7 lines
Quoted 3 lines

I think you need to be more specific with the comparison.

Andrew

Oh, I see. So you mean "phy-mode" property should belong to controller, not port? I thought one controller can have at most one port.

If you look at mv643xx_eth_shared_of_probe(), it appears a controller can have multiple ports. And:

        if (dev_num == 3) {
                dev_err(&pdev->dev, "too many ports registered\n");
                return -EINVAL;
        }

I don't know the details?

Andrew

author
#6 lore raw

PATCH v3 1/1 net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
v2: clarify modes work on controllers, read default value from PSC1
v3: Kirkwood only

 drivers/net/ethernet/marvell/mv643xx_eth.c | 48 ++++++++++++++++++++--
 1 file changed, 44 insertions(+), 4 deletions(-)
drivers/net/ethernet/marvell/mv643xx_eth.c +44 -4
index b6be0552a..355bb8ba7 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -367,6 +368,7 @@ struct mv643xx_eth_private {
 	struct mv643xx_eth_shared_private *shared;
 	void __iomem *base;
 	int port_num;
+	bool kirkwood;
 
 	struct net_device *dev;
 
@@ -1215,6 +1217,7 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 	             DISABLE_AUTO_NEG_SPEED_GMII |
 		     DISABLE_AUTO_NEG_FOR_FLOW_CTRL |
 		     DISABLE_AUTO_NEG_FOR_DUPLEX;
+	u32 psc1r;
 
 	if (dev->phydev->autoneg == AUTONEG_ENABLE) {
 		/* enable auto negotiation */
@@ -1245,6 +1248,36 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
 	wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+	if (mp->kirkwood) {
+		psc1r = rdlp(mp, PORT_SERIAL_CONTROL1);
+		/* On Kirkwood with two Ethernet controllers, if both of them
+		 * have RGMII_EN disabled, the first controller will be in GMII
+		 * mode and the second one is effectively disabled, instead of
+		 * two MII interfaces.
+		 *
+		 * To enable GMII in the first controller, the second one must
+		 * also be configured (and may be enabled) with RGMII_EN
+		 * disabled too, even though it cannot be used at all.
+		 */
+		switch (dev->phydev->interface) {
+		case PHY_INTERFACE_MODE_MII:
+		case PHY_INTERFACE_MODE_GMII:
+			psc1r &= ~RGMII_EN;
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+		case PHY_INTERFACE_MODE_RGMII_ID:
+		case PHY_INTERFACE_MODE_RGMII_RXID:
+		case PHY_INTERFACE_MODE_RGMII_TXID:
+			psc1r |= RGMII_EN;
+			break;
+		default:
+			/* Unknown; don't touch */
+			break;
+		}
+
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r);
+	}
 }
 
 /* statistics ***************************************************************/
@@ -2975,11 +3008,16 @@ static int get_phy_mode(struct mv643xx_eth_private *mp)
 	if (dev->of_node)
 		err = of_get_phy_mode(dev->of_node, &iface);
 
-	/* Historical default if unspecified. We could also read/write
-	 * the interface state in the PSC1
+	/* Read the interface state in the PSC1.
+	 *
+	 * Modes of two devices may interact on Kirkwood. Currently there is no
+	 * way to detect another device within this scope; blindly set MII
+	 * here.
 	 */
 	if (!dev->of_node || err)
-		iface = PHY_INTERFACE_MODE_GMII;
+		iface = rdlp(mp, PORT_SERIAL_CONTROL1) & RGMII_EN ?
+			PHY_INTERFACE_MODE_RGMII : mp->kirkwood ?
+			PHY_INTERFACE_MODE_MII : PHY_INTERFACE_MODE_GMII;
 	return iface;
 }
 
@@ -3124,9 +3162,11 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 	 * all other SoCs/System Controllers using this driver.
 	 */
 	if (of_device_is_compatible(pdev->dev.of_node,
-				    "marvell,kirkwood-eth-port"))
+				    "marvell,kirkwood-eth-port")) {
 		wrlp(mp, PORT_SERIAL_CONTROL1,
 		     rdlp(mp, PORT_SERIAL_CONTROL1) & ~CLK125_BYPASS_EN);
+		mp->kirkwood = 1;
+	}
 
 	/*
 	 * Start with a default rate, and if there is a clock, allow
Signature · 1 line
2.35.1
author
#7 lore raw

PATCH v4 1/1 net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
v2: clarify modes work on controllers, read default value from PSC1
v3: Kirkwood only
v4: cleanup

 drivers/net/ethernet/marvell/mv643xx_eth.c | 57 +++++++++++++++++++---
 1 file changed, 51 insertions(+), 6 deletions(-)
drivers/net/ethernet/marvell/mv643xx_eth.c +51 -6
index b6be0552a..4d4ee36b5 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -1215,6 +1216,7 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 	             DISABLE_AUTO_NEG_SPEED_GMII |
 		     DISABLE_AUTO_NEG_FOR_FLOW_CTRL |
 		     DISABLE_AUTO_NEG_FOR_DUPLEX;
+	u32 psc1r;
 
 	if (dev->phydev->autoneg == AUTONEG_ENABLE) {
 		/* enable auto negotiation */
@@ -1245,6 +1247,38 @@ static void mv643xx_eth_adjust_link(struct net_device *dev)
 
 out_write:
 	wrlp(mp, PORT_SERIAL_CONTROL, pscr);
+
+	if (dev->dev->of_node &&
+	    of_device_is_compatible(dev->dev->of_node,
+				    "marvell,kirkwood-eth-port")) {
+		psc1r = rdlp(mp, PORT_SERIAL_CONTROL1);
+		/* On Kirkwood with two Ethernet controllers, if both of them
+		 * have RGMII_EN disabled, the first controller will be in GMII
+		 * mode and the second one is effectively disabled, instead of
+		 * two MII interfaces.
+		 *
+		 * To enable GMII in the first controller, the second one must
+		 * also be configured (and may be enabled) with RGMII_EN
+		 * disabled too, even though it cannot be used at all.
+		 */
+		switch (dev->phydev->interface) {
+		case PHY_INTERFACE_MODE_MII:
+		case PHY_INTERFACE_MODE_GMII:
+			psc1r &= ~RGMII_EN;
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+		case PHY_INTERFACE_MODE_RGMII_ID:
+		case PHY_INTERFACE_MODE_RGMII_RXID:
+		case PHY_INTERFACE_MODE_RGMII_TXID:
+			psc1r |= RGMII_EN;
+			break;
+		default:
+			/* Unknown; don't touch */
+			break;
+		}
+
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r);
+	}
 }
 
 /* statistics ***************************************************************/
@@ -2972,15 +3006,26 @@ static int get_phy_mode(struct mv643xx_eth_private *mp)
 	phy_interface_t iface;
 	int err;
 
-	if (dev->of_node)
+	if (dev->of_node) {
 		err = of_get_phy_mode(dev->of_node, &iface);
+		if (!err)
+			return iface;
+	}
+
+	/* Read the interface state in the PSC1 */
+	if (rdlp(mp, PORT_SERIAL_CONTROL1) & RGMII_EN)
+		return PHY_INTERFACE_MODE_RGMII;
 
-	/* Historical default if unspecified. We could also read/write
-	 * the interface state in the PSC1
+	/* Modes of two devices may interact on Kirkwood. Currently there is no
+	 * way to detect another device within this scope; blindly set MII
+	 * here.
 	 */
-	if (!dev->of_node || err)
-		iface = PHY_INTERFACE_MODE_GMII;
-	return iface;
+	if (dev->of_node &&
+	    of_device_is_compatible(dev->of_node, "marvell,kirkwood-eth"))
+		return PHY_INTERFACE_MODE_MII;
+
+	/* Historical default if unspecified */
+	return PHY_INTERFACE_MODE_GMII;
 }
 
 static struct phy_device *phy_scan(struct mv643xx_eth_private *mp,
Signature · 1 line
2.35.1
maintainer
#8 lore raw

Re: [PATCH v4] net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood

Quoted 7 lines · On Sat, 1 Oct 2022 06:25:39 +0800 David Yang wrote:

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

Well, this version does not build:

drivers/net/ethernet/marvell/mv643xx_eth.c:1252:38: error: member reference type 'struct device' is not a pointer; did you mean to use '.'?

            of_device_is_compatible(dev->dev->of_node,
                                    ~~~~~~~~^~
                                            .
author
#9 lore raw

PATCH v5 1/1 net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII mode, the first controller enters GMII mode, while the second controller is effectively disabled. This requires configuring (and maybe enabling) the second controller in the device tree, even though it cannot be used.

---
v2: clarify modes work on controllers, read default value from PSC1
v3: Kirkwood only
v4: cleanup
v5: test on 88f6282

 drivers/net/ethernet/marvell/mv643xx_eth.c | 49 ++++++++++++++++++----
 include/linux/mv643xx_eth.h                |  1 +
 2 files changed, 43 insertions(+), 7 deletions(-)
drivers/net/ethernet/marvell/mv643xx_eth.c +42 -7
index b6be0552a..ed674c512 100644
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -2761,6 +2762,8 @@ static int mv643xx_eth_shared_of_add_port(struct platform_device *pdev,
 	mv643xx_eth_property(pnp, "rx-sram-addr", ppd.rx_sram_addr);
 	mv643xx_eth_property(pnp, "rx-sram-size", ppd.rx_sram_size);
 
+	of_get_phy_mode(pnp, &ppd.interface);
+
 	ppd.phy_node = of_parse_phandle(pnp, "phy-handle", 0);
 	if (!ppd.phy_node) {
 		ppd.phy_addr = MV643XX_ETH_PHY_NONE;
@@ -3092,6 +3095,7 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 	struct mv643xx_eth_private *mp;
 	struct net_device *dev;
 	struct phy_device *phydev = NULL;
+	u32 psc1r;
 	int err, irq;
 
 	pd = dev_get_platdata(&pdev->dev);
@@ -3119,14 +3123,45 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 
 	mp->dev = dev;
 
-	/* Kirkwood resets some registers on gated clocks. Especially
-	 * CLK125_BYPASS_EN must be cleared but is not available on
-	 * all other SoCs/System Controllers using this driver.
-	 */
 	if (of_device_is_compatible(pdev->dev.of_node,
-				    "marvell,kirkwood-eth-port"))
-		wrlp(mp, PORT_SERIAL_CONTROL1,
-		     rdlp(mp, PORT_SERIAL_CONTROL1) & ~CLK125_BYPASS_EN);
+				    "marvell,kirkwood-eth-port")) {
+		psc1r = rdlp(mp, PORT_SERIAL_CONTROL1);
+
+		/* Kirkwood resets some registers on gated clocks. Especially
+		 * CLK125_BYPASS_EN must be cleared but is not available on
+		 * all other SoCs/System Controllers using this driver.
+		 */
+		psc1r &= ~CLK125_BYPASS_EN;
+
+		/* On Kirkwood with two Ethernet controllers, if both of them
+		 * have RGMII_EN disabled, the first controller will be in GMII
+		 * mode and the second one is effectively disabled, instead of
+		 * two MII interfaces.
+		 *
+		 * To enable GMII in the first controller, the second one must
+		 * also be configured (and may be enabled) with RGMII_EN
+		 * disabled too, even though it cannot be used at all.
+		 */
+		switch (pd->interface) {
+		/* Use internal to denote second controller being disabled */
+		case PHY_INTERFACE_MODE_INTERNAL:
+		case PHY_INTERFACE_MODE_MII:
+		case PHY_INTERFACE_MODE_GMII:
+			psc1r &= ~RGMII_EN;
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+		case PHY_INTERFACE_MODE_RGMII_ID:
+		case PHY_INTERFACE_MODE_RGMII_RXID:
+		case PHY_INTERFACE_MODE_RGMII_TXID:
+			psc1r |= RGMII_EN;
+			break;
+		default:
+			/* Unknown; don't touch */
+			break;
+		}
+
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r);
+	}
 
 	/*
 	 * Start with a default rate, and if there is a clock, allow
include/linux/mv643xx_eth.h +1 -0
index 3682ae75c..14dc448f0 100644
@@ -59,6 +59,7 @@ struct mv643xx_eth_platform_data {
 	 */
 	int			speed;
 	int			duplex;
+	phy_interface_t		interface;
 
 	/*
 	 * How many RX/TX queues to use.
Signature · 1 line
2.35.1