iio: adc: add max11410 adc driver
Subsystems (3)
v7 cover iio: adc: add max11410 adc driver
Note: No sign-off tag for David as he was unreachable when the initial patch was sent.
Changelog:
since v7:
- add asm-generic/unaligned.h header (reported by kernel test robot)
- dtbinding: specify 2 items for interrupt-names
- dtbinding: reorder required block
since v6:
- don't require avdd supply if not needed
since v5:
- allow user to specify both interrupt pins
- keep irq info in max11410_state struct and use irq by name
- get irqs by fwnode_get_irq_byname
- don't allocate trigger when no irq supplied
- fix deadlock condition in write_raw
- minor style fixes
- fix devicetree binding errors reported by dt_binding_check
- convert module license to GPL as suggested by checkpatch
since v4:
- add in_voltage_filter2_notch_{center,en} attrs for sinc4 filter
- add ABI documentation for filter sysfs
- check interrupt-names property for configuring gpio of max11410
- remove hardwaregain property
- add scale_available property for channes using PGA
- separate vref regulator error -ENODEV from other errors
- don't register trigger if no irq specified
- style fixes
since v3:
- prefix defines with MAX11410_
- group vref regulators
- use builtin iio_validate_scan_mask_onehot
- validate iio trigger
- move scan data into state struct
- require vrefn regulator in DT if used by any channel
- don't require irq for triggered buffer
- remove filter sysfs attr and ABI documentation
- add in_voltage_filter[0-1]_notch_{center,en} attrs
since v2:
- remove bit position shifting, use field_prep instead
- reduce the amount of reg writes in max11410_configure_channel
- add error checking in max11410_parse_channels
- remove some unneeded blank lines and minor style fixes
- remove scan data assignment in max11410_trigger_handler
Ibrahim Tilki (3):
iio: adc: add max11410 adc driver
dt-bindings: iio: adc: add adi,max11410.yaml
Documentation: ABI: testing: add max11410 doc
.../ABI/testing/sysfs-bus-iio-adc-max11410 | 13 + .../bindings/iio/adc/adi,max11410.yaml | 176 +++ drivers/iio/adc/Kconfig | 13 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/max11410.c | 1050 +++++++++++++++++ 5 files changed, 1253 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-adc-max11410 create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml create mode 100644 drivers/iio/adc/max11410.c
Signature · 1 line
2.25.1
PATCH v7 1/3 iio: adc: add max11410 adc driver
Adding support for max11410 24-bit, 1.9ksps delta-sigma adc which has 3 differential reference and 10 differential channel inputs. Inputs and references can be buffered internally. Inputs can also be amplified with internal PGA.
Device has four digital filter modes: FIR50/60, FIR50, FIR60 and SINC4. FIR 50Hz and 60Hz rejections can be enabled/disabled separately. Digital filter selection affects sampling frequency range so driver has to consider the configured filter when configuring sampling frequency.
--- drivers/iio/adc/Kconfig | 13 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/max11410.c | 1050 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1064 insertions(+) create mode 100644 drivers/iio/adc/max11410.c
drivers/iio/adc/Kconfig +13 -0
@@ -667,6 +667,19 @@ config MAX11205 To compile this driver as a module, choose M here: the module will be called max11205. +config MAX11410 + tristate "Analog Devices MAX11410 ADC driver" + depends on SPI + select REGMAP_SPI + select IIO_BUFFER + select IIO_TRIGGER + select IIO_TRIGGERED_BUFFER + help + Say yes here to build support for Analog Devices MAX11410 ADCs. + + To compile this driver as a module, choose M here: the module will be + called max11410. + config MAX1241 tristate "Maxim max1241 ADC driver" depends on SPI_MASTER
drivers/iio/adc/Makefile +1 -0
@@ -62,6 +62,7 @@ obj-$(CONFIG_MAX1027) += max1027.o obj-$(CONFIG_MAX11100) += max11100.o obj-$(CONFIG_MAX1118) += max1118.o obj-$(CONFIG_MAX11205) += max11205.o +obj-$(CONFIG_MAX11410) += max11410.o obj-$(CONFIG_MAX1241) += max1241.o obj-$(CONFIG_MAX1363) += max1363.o obj-$(CONFIG_MAX9611) += max9611.o
drivers/iio/adc/max11410.c new file +1050 -0
1,050 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v7 2/3 dt-bindings: iio: adc: add adi,max11410.yaml
In reply to Ibrahim TilkiAdding devicetree binding documentation for max11410 adc.
--- .../bindings/iio/adc/adi,max11410.yaml | 176 ++++++++++++++++++ 1 file changed, 176 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml new file +176 -0
@@ -0,0 +1,176 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2022 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,max11410.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices MAX11410 ADC device driver + +maintainers: + - Ibrahim Tilki <[email protected]> + +description: | + Bindings for the Analog Devices MAX11410 ADC device. Datasheet can be + found here: + https://datasheets.maximintegrated.com/en/ds/MAX11410.pdf + +properties: + compatible: + enum: + - adi,max11410 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + description: Name of the gpio pin of max11410 used for IRQ + minItems: 1 + items: + - enum: [gpio0, gpio1] + - const: gpio1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + avdd-supply: + description: Optional avdd supply. Used as reference when no explicit reference supplied. + + vref0p-supply: + description: vref0p supply can be used as reference for conversion. + + vref1p-supply: + description: vref1p supply can be used as reference for conversion. + + vref2p-supply: + description: vref2p supply can be used as reference for conversion. + + vref0n-supply: + description: vref0n supply can be used as reference for conversion. + + vref1n-supply: + description: vref1n supply can be used as reference for conversion. + + vref2n-supply: + description: vref2n supply can be used as reference for conversion. + + spi-max-frequency: + maximum: 8000000 + +patternProperties: + "^channel(@[0-9])?$": + $ref: "adc.yaml" + type: object + description: Represents the external channels which are connected to the ADC. + + properties: + reg: + description: The channel number in single-ended mode. + minimum: 0 + maximum: 9 + + adi,reference: + description: | + Select the reference source to use when converting on + the specific channel. Valid values are: + 0: VREF0P/VREF0N + 1: VREF1P/VREF1N + 2: VREF2P/VREF2N + 3: AVDD/AGND + 4: VREF0P/AGND + 5: VREF1P/AGND + 6: VREF2P/AGND + If this field is left empty, AVDD/AGND is selected. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6] + default: 3 + + adi,input-mode: + description: | + Select signal path of input channels. Valid values are: + 0: Buffered, low-power, unity-gain path (default) + 1: Bypass path + 2: PGA path + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + + diff-channels: true + + bipolar: true + + settling-time-us: true + + adi,buffered-vrefp: + description: Enable buffered mode for positive reference. + type: boolean + + adi,buffered-vrefn: + description: Enable buffered mode for negative reference. + type: boolean + + required: + - reg + + additionalProperties: false + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "adi,max11410"; + spi-max-frequency = <8000000>; + + interrupt-parent = <&gpio>; + interrupts = <25 2>; + interrupt-names = "gpio1"; + + avdd-supply = <&adc_avdd>; + + vref1p-supply = <&adc_vref1p>; + vref1n-supply = <&adc_vref1n>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + }; + + channel@1 { + reg = <1>; + diff-channels = <2 3>; + adi,reference = <1>; + bipolar; + settling-time-us = <100000>; + }; + + channel@2 { + reg = <2>; + diff-channels = <7 9>; + adi,reference = <5>; + adi,input-mode = <2>; + settling-time-us = <50000>; + }; + }; + };
Signature · 1 line
2.25.1
Re: [PATCH v7 2/3] dt-bindings: iio: adc: add adi,max11410.yaml
Quoted 3 lines · Ibrahim Tilki
Adding devicetree binding documentation for max11410 adc.
Signed-off-by Ibrahim Tilki <[email protected]>
(...)
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml line 69
Quoted 9 lines
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml new file +9
-0+ vref2n-supply: + description: vref2n supply can be used as reference for conversion. + + spi-max-frequency: + maximum: 8000000 + +patternProperties: + "^channel(@[0-9])?$": + $ref: "adc.yaml"
No need for quotes.
Quoted 66 lines
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml new file +66
-0+ type: object + description: Represents the external channels which are connected to the ADC. + + properties: + reg: + description: The channel number in single-ended mode. + minimum: 0 + maximum: 9 + + adi,reference: + description: | + Select the reference source to use when converting on + the specific channel. Valid values are: + 0: VREF0P/VREF0N + 1: VREF1P/VREF1N + 2: VREF2P/VREF2N + 3: AVDD/AGND + 4: VREF0P/AGND + 5: VREF1P/AGND + 6: VREF2P/AGND + If this field is left empty, AVDD/AGND is selected. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6] + default: 3 + + adi,input-mode: + description: | + Select signal path of input channels. Valid values are: + 0: Buffered, low-power, unity-gain path (default) + 1: Bypass path + 2: PGA path + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + + diff-channels: true + + bipolar: true + + settling-time-us: true + + adi,buffered-vrefp: + description: Enable buffered mode for positive reference. + type: boolean + + adi,buffered-vrefn: + description: Enable buffered mode for negative reference. + type: boolean + + required: + - reg + + additionalProperties: false + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + spi {
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml line 145
Quoted 10 lines
Documentation/devicetree/bindings/iio/adc/adi,max11410.yaml new file +10
-0+ #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "adi,max11410"; + spi-max-frequency = <8000000>; + + interrupt-parent = <&gpio>; + interrupts = <25 2>;
What does the 2 stand for? I already asked to fix this.
Best regards,
Krzysztof
PATCH v7 3/3 Documentation: ABI: testing: add max11410 doc
In reply to Ibrahim TilkiAdding documentation for Analog Devices max11410 adc userspace sysfs.
--- .../ABI/testing/sysfs-bus-iio-adc-max11410 | 13 +++++++++++++ 1 file changed, 13 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-adc-max11410
Documentation/ABI/testing/sysfs-bus-iio-adc-max11410 new file +13 -0
@@ -0,0 +1,13 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_filterY_notch_en +Date: September 2022 +KernelVersion: 6.0 +Contact: [email protected] +Description: + Enable or disable a notch filter. + +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_filterY_notch_center +Date: September 2022 +KernelVersion: 6.0 +Contact: [email protected] +Description: + Center frequency of the notch filter in Hz.
Signature · 1 line
2.25.1