configs/lichee_rv: new defconfig
PATCH 1/1 configs/lichee_rv: new defconfig
Lichee RV - Nezha CM is a compute module with modular design, equipped with Allwinner D1 chip (based on T-Head XuanTie C906 core), 512MB DDR3 RAM.
Board support is based on the nezha defconfig already available in buildroot.
https://wiki.sipeed.com/hardware/en/lichee/RV/RV.html
https://linux-sunxi.org/Sipeed_Lichee_RV
Signed-off-by Angelo Compagnucci <[email protected]>
--- board/lichee_rv/genimage.cfg | 37 +++++++++++++ ...t-building-u-boot.toc1-for-lichee-rv.patch | 54 +++++++++++++++++++ board/lichee_rv/readme.txt | 26 +++++++++ configs/lichee_rv_defconfig | 34 ++++++++++++ 4 files changed, 151 insertions(+) create mode 100644 board/lichee_rv/genimage.cfg create mode 100644 board/lichee_rv/patches_rv/uboot/0002-Makefile-HACK-Support-building-u-boot.toc1-for-lichee-rv.patch create mode 100644 board/lichee_rv/readme.txt create mode 100644 configs/lichee_rv_defconfig
board/lichee_rv/genimage.cfg new file +37 -0
@@ -0,0 +1,37 @@ +# Minimal SD card image for the Allwinner Nezha + +image sdcard.img { + hdimage { + } + + partition boot0-1 { + in-partition-table = "no" + image = "boot0_sdcard_sun20iw1p1.bin" + offset = 8K + } + + partition boot0-2 { + in-partition-table = "no" + image = "boot0_sdcard_sun20iw1p1.bin" + offset = 128K + } + + partition u-boot-1 { + in-partition-table = "no" + image = "u-boot.toc1" + offset = 12M + } + + partition u-boot-2 { + in-partition-table = "no" + image = "u-boot.toc1" + offset = 16400K + } + + partition rootfs { + partition-type = 0x83 + image = "rootfs.ext4" + bootable = "true" + offset = 18M + } +}
board/lichee_rv/patches_rv/uboot/0002-Makefile-HACK-Support-building-u-boot.toc1-for-lichee-rv.patch new file +54 -0
54 lines not on this page · raw message
board/lichee_rv/readme.txt new file +26 -0
@@ -0,0 +1,26 @@ +Lichee RV +=============== + +Lichee RV - Nezha CM is a compute module with modular design, equipped +with Allwinner D1 chip (based on T-Head XuanTie C906 core), 512MB DDR3 RAM. +It can boot from TF card or SD-NAND, uses two sets of M.2 b key 67 pin +connectors to route all IO, making it convient for wide use and easy to replace. + +How to build +============ + +$ make lichee_rv_defconfig +$ make + +How to write the SD card +======================== + +Once the build process is finished you will have an image called "sdcard.img" +in the output/images/ directory. + +Copy the bootable "sdcard.img" onto an SD card with "dd": + + $ sudo dd if=output/images/sdcard.img of=/dev/sdX + +Connect a TTL UART to the debug connector, insert the microSD card and +plug in a USB-C cable to the PWR connector to boot the system.
configs/lichee_rv_defconfig new file +34 -0
@@ -0,0 +1,34 @@ +BR2_riscv=y +BR2_GLOBAL_PATCH_DIR="board/lichee_rv/patches_rv" +BR2_ROOTFS_OVERLAY="board/nezha/overlay" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/lichee_rv/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,smaeul,linux,f4bce410a6b47606557cb0d291572afc4c240c85)/linux-f4bce410a6b47606557cb0d291572afc4c240c85.tar.gz" +BR2_LINUX_KERNEL_DEFCONFIG="nezha" +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="allwinner/sun20i-d1-lichee-rv" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +# BR2_TARGET_ROOTFS_TAR is not set +BR2_TARGET_OPENSBI=y +BR2_TARGET_OPENSBI_CUSTOM_TARBALL=y +BR2_TARGET_OPENSBI_CUSTOM_TARBALL_LOCATION="$(call github,smaeul,opensbi,4bcaf9aa1dbc69ccb68998c7d462ef895163d493)/opensbi-4bcaf9aa1dbc69ccb68998c7d462ef895163d493.tar.gz" +BR2_TARGET_OPENSBI_PLAT="generic" +# BR2_TARGET_OPENSBI_INSTALL_JUMP_IMG is not set +BR2_TARGET_SUN20I_D1_SPL=y +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,smaeul,u-boot,7446a47204fd8923b99ced0091667979c4fd27fa)/uboot-7446a47204fd8923b99ced0091667979c4fd27fa.tar.gz" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="lichee_rv" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y +BR2_TARGET_UBOOT_NEEDS_OPENSBI=y +# BR2_TARGET_UBOOT_FORMAT_BIN is not set +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.toc1" +BR2_PACKAGE_HOST_GENIMAGE=y
Signature · 6 lines
2.25.1 _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot