ARM: dts: imx7d-sdb: config the max pressure for tsc2046
Sasha Levin
maintainerPATCH 1/6 ARM: dts: imx7d-sdb: config the max pressure for tsc2046
From: Haibo Chen <[email protected]>
[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]
Use the general touchscreen method to config the max pressure for touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for ABS_PRESSURE, when config the same max and min value, weston will meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen [17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE [17:19:39.183] event1 - ADS7846 Touchscreen: was rejected [17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator could not load cursor 'dnd-move' could not load cursor 'dnd-copy' could not load cursor 'dnd-none' No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max" belong to the deprecated properties, so remove them. Also for "ti,x-min", "ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default value in driver, so are redundant, also remove here.
--- arch/arm/boot/dts/imx7d-sdb.dts | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
arch/arm/boot/dts/imx7d-sdb.dts +1 -6
@@ -126,12 +126,7 @@ tsc2046@0 { interrupt-parent = <&gpio2>; interrupts = <29 0>; pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>; - ti,x-min = /bits/ 16 <0>; - ti,x-max = /bits/ 16 <0>; - ti,y-min = /bits/ 16 <0>; - ti,y-max = /bits/ 16 <0>; - ti,pressure-max = /bits/ 16 <0>; - ti,x-plate-ohms = /bits/ 16 <400>; + touchscreen-max-pressure = <255>; wakeup-source; }; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 2/6 ARM: dts: imx6q: add missing properties for sram
From: Alexander Stein <[email protected]>
[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6q.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6q.dtsi +3 -0
@@ -82,6 +82,9 @@ soc { ocram: sram@00900000 { compatible = "mmio-sram"; reg = <0x00900000 0x40000>; + ranges = <0 0x00900000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 3/6 ARM: dts: imx6dl: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6dl.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6dl.dtsi +3 -0
@@ -63,6 +63,9 @@ soc { ocram: sram@00900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 4/6 ARM: dts: imx6qp: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property sram@940000: '#size-cells' is a required property sram@940000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/imx6qp.dtsi +6 -0
@@ -47,12 +47,18 @@ soc { ocram2: sram@00940000 { compatible = "mmio-sram"; reg = <0x00940000 0x20000>; + ranges = <0 0x00940000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; }; ocram3: sram@00960000 { compatible = "mmio-sram"; reg = <0x00960000 0x20000>; + ranges = <0 0x00960000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 5/6 ARM: dts: imx6sl: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6sl.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6sl.dtsi +3 -0
@@ -102,6 +102,9 @@ soc { ocram: sram@00900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6SL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 6/6 ARM: orion: fix include path
In reply to Sasha LevinFrom: Arnd Bergmann <[email protected]>
[ Upstream commit 63872304bdb3decd5454f4dd210c25395278ed13 ]
Now that CONFIG_ARCH_MULTIPLATFORM can be disabled anywhere, there is a build failure for plat-orion:
arch/arm/plat-orion/irq.c:19:10: fatal error: plat/irq.h: No such file or directory
Make the include path unconditional.
--- arch/arm/plat-orion/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/plat-orion/Makefile +1 -1
@@ -1,7 +1,7 @@ # # Makefile for the linux kernel. # -ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include +ccflags-y := -I$(srctree)/$(src)/include orion-gpio-$(CONFIG_GPIOLIB) += gpio.o obj-$(CONFIG_PLAT_ORION_LEGACY) += irq.o pcie.o time.o common.o mpp.o
Signature · 1 line
2.35.1
Hi!
Quoted 22 lines
From: Haibo Chen <[email protected]>
[ Upstream commit
e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272]Use the general touchscreen method to config the max pressure for touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will meet the following issue,[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen [17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE [17:19:39.183] event1 - ADS7846 Touchscreen: was rejected [17:19:39.183] event1 - not using input device '/dev/input/event1'This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator could not load cursor 'dnd-move' could not load cursor 'dnd-copy' could not load cursor 'dnd-none' No devices listed.
Quoted 4 lines
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max" belong to the deprecated properties, so remove them. Also for "ti,x-min", "ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default value in driver, so are redundant, also remove here.
Did someone check the source code in 4.9? AFAICT it still tries to use the properties, and probing seems to be different from newer kernels.
Best regards,
Pavel
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany