arm64: dts: freescale: imx8dxl: add scu_gpio node
Subsystems (2)
PATCH 1/2 arm64: dts: freescale: imx8dxl: add scu_gpio node
add scu_gpio node in system-controller.
--- arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/freescale/imx8dxl.dtsi +6 -0
@@ -133,6 +133,12 @@ clk: clock-controller { clock-names = "xtal_32KHz", "xtal_24Mhz"; }; + scu_gpio: gpio { + compatible = "fsl,imx8qxp-sc-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + iomuxc: pinctrl { compatible = "fsl,imx8dxl-iomuxc"; };
Signature · 1 line
2.34.1
PATCH 2/2 arm64: dts: freescale: imx8dxl-evk: enable mii_select node
The mii_select node is used to determine the fec1's interface type. Using "enable-active-high" property to configure the interface type as "RMII". Deleting the property as "RGMII".
--- arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts +10 -0
@@ -90,6 +90,16 @@ reg_usdhc2_vmmc: regulator-3 { enable-active-high; off-on-delay-us = <3480>; }; + + mii_select: regulator-4 { + compatible = "regulator-fixed"; + regulator-name = "mii-select"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&scu_gpio 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; }; &eqos {
Signature · 1 line
2.34.1
A soft ping to Shawn.
Thanks,
Shenwei
Quoted 40 lines
-----Original Message-----
From: Shenwei Wang <[email protected]>
Sent: Tuesday, October 11, 2022 2:47 PM
To: Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Shawn Guo <[email protected]>; Sascha Hauer <[email protected]>
Cc: Pengutronix Kernel Team <[email protected]>; Fabio Estevam <[email protected]>; dl-linux-imx <[email protected]>; Shenwei Wang <[email protected]>; Viorel Suman <[email protected]>; Abel Vesa <[email protected]>; Ming Qian <[email protected]>; Peng Fan <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 1/2] arm64: dts: freescale: imx8dxl: addscu_gpionodeadd
scu_gpionode in system-controller.Signed-off-by Shenwei Wang <[email protected]>--- arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)arch/arm64/boot/dts/freescale/imx8dxl.dtsi +6
-1@@ -133,6 +133,12 @@ clk: clock-controller { clock-names = "xtal_32KHz", "xtal_24Mhz"; }; + scu_gpio: gpio { + compatible = "fsl,imx8qxp-sc-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + iomuxc: pinctrl { compatible = "fsl,imx8dxl-iomuxc"; }; --2.34.1
Shawn Guo
AppliedQuoted 3 lines · Shenwei Wang
add
scu_gpionode in system-controller.Signed-off-by Shenwei Wang <[email protected]>
Applied both, thanks!