Skip to contentSkip to conversation

spi: spi-imx: mx51 support for more than 4 gpio chip selects

PATCH Superseded Chris Lesiak 1 participant 1 message Oct 17, 2022

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spi: spi-imx: mx51 support for more than 4 gpio chip selects

The MX51_ECSPI_CTRL and MX51_ECSPI_CONFIG registers have bit fields that only support the four slave select channels. If we are using a gpio to support chip_select > 3, we need to be careful not to write outside the bit fields. Probably the biggest issue is the 2-bit CHANNEL_SELECT field of MX51_ECSPI_CTRL overflowing into the BURST_LENGTH field. That will likely cause a DMA TX timeout.

To prevent this, when chip_select > 3, use slave select = 3.

This should allow up to four channels using the built-in slave selects, or any of the first three chip selects optionally using built-in slave selects with gpio used for additional channels.

---
 drivers/spi/spi-imx.c | 43 ++++++++++++++++++++++++++++++++-----------
 1 file changed, 32 insertions(+), 11 deletions(-)
drivers/spi/spi-imx.c +32 -11
index 30d82cc7300b..9c4e979ab74d 100644
@@ -253,6 +253,8 @@ static bool spi_imx_can_dma(struct spi_controller *controller, struct spi_device
        return true;
 }
 
+#define MX51_ECSPI_MAX_HW_CS           3
+
 #define MX51_ECSPI_CTRL                0x08
 #define MX51_ECSPI_CTRL_ENABLE         (1 <<  0)
 #define MX51_ECSPI_CTRL_XCH            (1 <<  2)
@@ -521,6 +523,17 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
        u32 testreg, delay;
        u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
        u32 current_cfg = cfg;
+       u8 hw_chip_select;
+
+       if (spi->cs_gpiod) {
+               hw_chip_select = MX51_ECSPI_MAX_HW_CS;
+       } else if (spi->chip_select <= MX51_ECSPI_MAX_HW_CS) {
+               hw_chip_select = spi->chip_select;
+       } else {
+               dev_err(spi_imx->dev, "hardware chip select is out of range: %i\n",
+                       spi->chip_select);
+               return -EINVAL;
+       }
 
        /* set Master or Slave mode */
        if (spi_imx->slave_mode)
@@ -535,7 +548,7 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
                ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
 
        /* set chip select to use */
-       ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
+       ctrl |= MX51_ECSPI_CTRL_CS(hw_chip_select);
 
        /*
         * The ctrl register must be written first, with the EN bit set other
@@ -556,22 +569,22 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
         * BURST_LENGTH + 1 bits are received
         */
        if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
-               cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+               cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(hw_chip_select);
        else
-               cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+               cfg |= MX51_ECSPI_CONFIG_SBBCTRL(hw_chip_select);
 
        if (spi->mode & SPI_CPOL) {
-               cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
-               cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+               cfg |= MX51_ECSPI_CONFIG_SCLKPOL(hw_chip_select);
+               cfg |= MX51_ECSPI_CONFIG_SCLKCTL(hw_chip_select);
        } else {
-               cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
-               cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+               cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(hw_chip_select);
+               cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(hw_chip_select);
        }
 
        if (spi->mode & SPI_CS_HIGH)
-               cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+               cfg |= MX51_ECSPI_CONFIG_SSBPOL(hw_chip_select);
        else
-               cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+               cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(hw_chip_select);
 
        if (cfg == current_cfg)
                return 0;
@@ -616,14 +629,22 @@ static void mx51_configure_cpha(struct spi_imx_data *spi_imx,
        bool cpha = (spi->mode & SPI_CPHA);
        bool flip_cpha = (spi->mode & SPI_RX_CPHA_FLIP) && spi_imx->rx_only;
        u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
+       u8 hw_chip_select;
+
+       if (spi->cs_gpiod)
+               hw_chip_select = MX51_ECSPI_MAX_HW_CS;
+       else if (spi->chip_select <= MX51_ECSPI_MAX_HW_CS)
+               hw_chip_select = spi->chip_select;
+       else
+               return;
 
        /* Flip cpha logical value iff flip_cpha */
        cpha ^= flip_cpha;
 
        if (cpha)
-               cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+               cfg |= MX51_ECSPI_CONFIG_SCLKPHA(hw_chip_select);
        else
-               cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+               cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(hw_chip_select);
 
        writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
 }

--
2.26.2

Chris Lesiak
Principal Design Engineer, Software
402-467-0693