ke-am62x-sk_evm: add ospi support
cover ke-am62x-sk_evm: add ospi support
There's a S28HS512T Flash (by Cypress) on the AM625 SK EVM.
- Add necessary DT nodes to enable OSPI interface with this flash.
- Enable all configs that enable the OSPI related drivers and commands like SF probe.
Tested on my AM62 SK EVM, attaching logs below.
Logs:
------------------------------------------------------------------------
U-Boot SPL 2022.10-rc5-00012-g435596d57f8b-dirty (Sep 26 2022 - 16:27:48 +0530)
SYSFW ABI: 3.1 (firmware rev 0x0008 '8.4.6--v08.04.06 (Jolly Jellyfi') Trying to boot from MMC2
Starting ATF on ARM64 core...
NOTICE: BL31: v2.7(release):v2.7.0-dirty NOTICE: BL31: Built : 14:30:02, Aug 27 2022
U-Boot SPL 2022.10-rc5-00012-g435596d57f8b-dirty (Sep 26 2022 - 17:51:27 +0530)
SYSFW ABI: 3.1 (firmware rev 0x0008 '8.4.6--v08.04.06 (Jolly Jellyfi') Trying to boot from MMC2
U-Boot 2022.10-rc5-00012-g435596d57f8b-dirty (Sep 26 2022 - 17:51:27 +0530)
SoC: AM62X SR1.0 GP Model: Texas Instruments AM625 SK DRAM: 2 GiB Core: 37 devices, 18 uclasses, devicetree: separate MMC: mmc@fa10000: 2, mmc@fa00000: 1, mmc@fa20000: 3 Loading Environment from nowhere... OK In: serial@2800000 Out: serial@2800000 Err: serial@2800000 Net: No ethernet found. Hit any key to stop autoboot: 0
=> sf probe
SF: Detected s28hs512t with page size 256 Bytes, erase size 256 KiB, total 64 MiB
=> fatload mmc 1 $loadaddr tiboot3.bin
285482 bytes read in 17 ms (16 MiB/s)
=> sf update $loadaddr 0x0 $filesize
device 0 offset 0x0, size 0x45b2a
285482 bytes written, 0 bytes skipped in 2.623s, speed 111322 B/s => sf read 0x90000000 0x0 $filesize
device 0 offset 0x0, size 0x45b2a
SF: 285482 bytes @ 0x0 Read: OK
=> md $loadaddr
82000000: 94048230 fd038230 010203a0 64140202 0...0..........d 82000010: 3f829a45 85bb6dd8 232b5568 f8f4176f E..?.m..hU+#o... 82000020: 309fb7ff 2a09060d f7864886 0d01010d ...0...*.H...... 82000030: 81300005 300b319d 55030609 02130604 ..0..1.0...U.... 82000040: 0b315355 03060930 0c080455 31585402 US1.0...U....TX1 82000050: 060d300f 07045503 6144060c 73616c6c .0...U....Dallas 82000060: 25302731 04550306 541e0c0a 73617865 1'0%..U....Texas 82000070: 736e4920 6d757274 73746e65 636e4920 Instruments Inc 82000080: 6f70726f 65746172 30133164 55030611 orporated1.0...U 82000090: 0a0c0b04 636f7250 6f737365 13317372 ....Processors1. 820000a0: 03061130 0c030455 2049540a 70707553 0...U....TI Supp 820000b0: 3174726f 061b301d 48862a09 010df786 ort1.0...*.H.... 820000c0: 0e160109 70707573 4074726f 632e6974 [email protected] 820000d0: 1e306d6f 32320d17 36323930 38353031 om0...2209261058 820000e0: 175a3331 3132320d 31363230 31383530 13Z..22102610581 820000f0: 81305a33 300b319d 55030609 02130604 3Z0..1.0...U.... => md 0x90000000 90000000: 94048230 fd038230 010203a0 64140202 0...0..........d 90000010: 3f829a45 85bb6dd8 232b5568 f8f4176f E..?.m..hU+#o... 90000020: 309fb7ff 2a09060d f7864886 0d01010d ...0...*.H...... 90000030: 81300005 300b319d 55030609 02130604 ..0..1.0...U.... 90000040: 0b315355 03060930 0c080455 31585402 US1.0...U....TX1 90000050: 060d300f 07045503 6144060c 73616c6c .0...U....Dallas 90000060: 25302731 04550306 541e0c0a 73617865 1'0%..U....Texas 90000070: 736e4920 6d757274 73746e65 636e4920 Instruments Inc 90000080: 6f70726f 65746172 30133164 55030611 orporated1.0...U 90000090: 0a0c0b04 636f7250 6f737365 13317372 ....Processors1. 900000a0: 03061130 0c030455 2049540a 70707553 0...U....TI Supp 900000b0: 3174726f 061b301d 48862a09 010df786 ort1.0...*.H.... 900000c0: 0e160109 70707573 4074726f 632e6974 [email protected] 900000d0: 1e306d6f 32320d17 36323930 38353031 om0...2209261058 900000e0: 175a3331 3132320d 31363230 31383530 13Z..22102610581 900000f0: 81305a33 300b319d 55030609 02130604 3Z0..1.0...U....
=> cmp.b $loadaddr 0x90000000 $filesize
Total of 285482 byte(s) were the same
------------------------------------------------------------------------
Thus tested read, write and probe flash from u-boot prompt
Dhruva Gole (2):
arm: dts: k3-am625-sk: Add OSPI support
configs: am62x_evm_a53: Enable OSPI Flash support
arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++ configs/am62x_evm_a53_defconfig | 13 +++++ 3 files changed, 114 insertions(+)
Signature · 1 line
2.25.1
PATCH 1/2 arm: dts: k3-am625-sk: Add OSPI support
Add DT nodes to enable S28HS512T OSPI flash on the SK board.
--- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++ 2 files changed, 101 insertions(+)
arch/arm/dts/k3-am625-sk-u-boot.dtsi +24 -0
@@ -102,3 +102,27 @@ &main_mmc1_pins_default { u-boot,dm-spl; }; + +&fss { + u-boot,dm-spl; +}; + +&ospi0_pins_default { + u-boot,dm-spl; +}; + +&ospi0 { + u-boot,dm-spl; + + flash@0 { + u-boot,dm-spl; + + partitions { + u-boot,dm-spl; + + partition@3fc0000 { + u-boot,dm-spl; + }; + }; + }; +};
arch/arm/dts/k3-am625-sk.dts +77 -0
92 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH 1/2] arm: dts: k3-am625-sk: Add OSPI support
Quoted 6 lines · Dhruva Gole
Add DT nodes to enable S28HS512T OSPI flash on the SK board.
Signed-off-by Dhruva Gole <[email protected]>--- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++
What is the status of the non u-boot.dtsi portion of this patch with upstream Linux? Thanks.
Signature · 1 line
Tom
Re: [EXTERNAL] Re: [PATCH 1/2] arm: dts: k3-am625-sk: Add OSPI support
Hi Tom,
Quoted 11 lines · Tom Rini
Quoted 6 lines · Dhruva Gole
Add DT nodes to enable S28HS512T OSPI flash on the SK board.
Signed-off-by Dhruva Gole <[email protected]>--- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++What is the status of the non
u-boot.dtsiportion of this patch with upstream Linux? Thanks.
In upstream, please refer to https://elixir.bootlin.com/linux/latest/source/arch/arm64/boot/dts/ti/k3-am625-sk.dts#L24
spi0 = &ospi0;
and pinmux is all done in a similar fashion as I have done in these patches.
Quoted 1 line
Signature · 2 lines
Thanks and Regards, Dhruva Gole
Re: [EXTERNAL] Re: [PATCH 1/2] arm: dts: k3-am625-sk: Add OSPI support
Quoted 12 lines · Dhruva Gole
Hi Tom,
Quoted 9 lines · Tom Rini
Quoted 6 lines · Dhruva Gole
Add DT nodes to enable S28HS512T OSPI flash on the SK board.
Signed-off-by Dhruva Gole <[email protected]>--- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++
Quoted 8 lines
Quoted 2 lines
What is the status of the non
u-boot.dtsiportion of this patch with upstream Linux? Thanks.In upstream, please refer to https://elixir.bootlin.com/linux/latest/source/arch/arm64/boot/dts/ti/k3-am625-sk.dts#L24
spi0 = &ospi0;
and pinmux is all done in a similar fashion as I have done in these patches.
The preferred way to do this then is to post a patch syncing the whole of the DTS files with a given upstream tag then, so that it's clear and also so the trees stay up to date. This also applies to the patches you posted today.
Signature · 1 line
Tom
Re: [PATCH 1/2] arm: dts: k3-am625-sk: Add OSPI support
Quoted 18 lines · Tom Rini
Quoted 17 lines · Dhruva Gole
Hi Tom,
Quoted 11 lines · Tom Rini
Quoted 6 lines · Dhruva Gole
Add DT nodes to enable S28HS512T OSPI flash on the SK board.
Signed-off-by Dhruva Gole <[email protected]>--- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +++++++++ arch/arm/dts/k3-am625-sk.dts | 77 ++++++++++++++++++++++++++++What is the status of the non
u-boot.dtsiportion of this patch with upstream Linux? Thanks.In upstream, please refer to https://elixir.bootlin.com/linux/latest/source/arch/arm64/boot/dts/ti/k3-am625-sk.dts#L24
Quoted 8 lines
Quoted 3 lines
spi0 = &ospi0;
and pinmux is all done in a similar fashion as I have done in these patches.
The preferred way to do this then is to post a patch syncing the whole of the DTS files with a given upstream tag then, so that it's clear and also so the trees stay up to date. This also applies to the patches you posted today.
Okay noted, I will be sending out a new series where I will sync up the DTS files with kernel upstream.
Quoted 1 line
Also kindly note that the series https://lore.kernel.org/u-boot/[email protected]/ supersedes this series.
I will also be re-spinning that series based on the suggestions given so far.
Signature · 2 lines
Thanks and Regards, Dhruva Gole
PATCH 2/2 configs: am62x_evm_a53: Enable OSPI Flash support
In reply to Dhruva GoleSet the necessary config options that help to build the necessary drivers that support spansion S28HS512T Flash
--- configs/am62x_evm_a53_defconfig | 13 +++++++++++++ 1 file changed, 13 insertions(+)
configs/am62x_evm_a53_defconfig +13 -0
@@ -31,7 +31,11 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400 CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img" CONFIG_SPL_DM_MAILBOX=y +CONFIG_SPL_DM_SPI_FLASH=y CONFIG_SPL_POWER_DOMAIN=y +# CONFIG_SPL_SPI_FLASH_TINY is not set +CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPL_SPI_LOAD=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_SYS_BOOTM_LEN=0x800000 CONFIG_CMD_MMC=y
@@ -57,6 +61,12 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ADMA=y CONFIG_SPL_MMC_SDHCI_ADMA=y CONFIG_MMC_SDHCI_AM654=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_SOFT_RESET=y +CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_S28HS512T=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_SINGLE=y
@@ -70,6 +80,9 @@ CONFIG_DM_SERIAL=y CONFIG_SOC_DEVICE=y CONFIG_SOC_DEVICE_TI_K3=y CONFIG_SOC_TI=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_CADENCE_QSPI=y CONFIG_SYSRESET=y CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_TI_SCI=y
Signature · 1 line
2.25.1