Skip to contentSkip to conversation

watchdog: aspeed: Add pre-timeout interrupt support

PATCH In review Eddie James 2 participants 5 messages Oct 19, 2022 – Oct 20, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover watchdog: aspeed: Add pre-timeout interrupt support

Enable the watchdog pre-timeout interrupt if enabled in the device tree, and setup the relevant device trees.

Eddie James (3):
watchdog: aspeed: Add pre-timeout interrupt support
ARM: dts: aspeed: Setup watchdog pre-timeout interrupt
ARM: dts: aspeed: p10bmc: Set watchdog pre-timeout interrupt

 arch/arm/boot/dts/aspeed-bmc-ibm-bonnell.dts |  1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts |  1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts |  1 +
 arch/arm/boot/dts/aspeed-g5.dtsi             |  3 ++
 arch/arm/boot/dts/aspeed-g6.dtsi             |  4 ++
 drivers/watchdog/aspeed_wdt.c                | 54 +++++++++++++++++++-
 6 files changed, 62 insertions(+), 2 deletions(-)
Signature · 1 line
2.31.1
#1 lore raw

PATCH 1/3 watchdog: aspeed: Add pre-timeout interrupt support

Enable the pre-timeout interrupt if requested by device property.

---
 drivers/watchdog/aspeed_wdt.c | 54 +++++++++++++++++++++++++++++++++--
 1 file changed, 52 insertions(+), 2 deletions(-)
drivers/watchdog/aspeed_wdt.c +52 -2
index bd06622813eb..6a6d53a9e21c 100644
@@ -5,11 +5,14 @@
  * Joel Stanley <[email protected]>
  */
 
+#include <linux/bits.h>
 #include <linux/delay.h>
+#include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_irq.h>
 #include <linux/platform_device.h>
 #include <linux/watchdog.h>
 
@@ -22,24 +25,37 @@ struct aspeed_wdt {
 	struct watchdog_device	wdd;
 	void __iomem		*base;
 	u32			ctrl;
+	u8			stop : 1;
 };
 
 struct aspeed_wdt_config {
 	u32 ext_pulse_width_mask;
+	u32 irq_shift;
+	u32 irq_mask;
 };
 
 static const struct aspeed_wdt_config ast2400_config = {
 	.ext_pulse_width_mask = 0xff,
+	.irq_shift = 0,
+	.irq_mask = 0,
 };
 
 static const struct aspeed_wdt_config ast2500_config = {
 	.ext_pulse_width_mask = 0xfffff,
+	.irq_shift = 12,
+	.irq_mask = GENMASK(31, 12),
+};
+
+static const struct aspeed_wdt_config ast2600_config = {
+	.ext_pulse_width_mask = 0xfffff,
+	.irq_shift = 0,
+	.irq_mask = GENMASK(31, 10),
 };
 
 static const struct of_device_id aspeed_wdt_of_table[] = {
 	{ .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config },
 	{ .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config },
-	{ .compatible = "aspeed,ast2600-wdt", .data = &ast2500_config },
+	{ .compatible = "aspeed,ast2600-wdt", .data = &ast2600_config },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
@@ -58,6 +74,7 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
 #define   WDT_CTRL_RESET_SYSTEM		BIT(1)
 #define   WDT_CTRL_ENABLE		BIT(0)
 #define WDT_TIMEOUT_STATUS	0x10
+#define   WDT_TIMEOUT_STATUS_IRQ		BIT(2)
 #define   WDT_TIMEOUT_STATUS_BOOT_SECONDARY	BIT(1)
 #define WDT_CLEAR_TIMEOUT_STATUS	0x14
 #define   WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION	BIT(0)
@@ -243,6 +260,17 @@ static const struct watchdog_info aspeed_wdt_info = {
 	.identity	= KBUILD_MODNAME,
 };
 
+static irqreturn_t aspeed_wdt_irq(int irq, void *arg)
+{
+	struct aspeed_wdt *wdt = arg;
+	u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
+
+	if (status & WDT_TIMEOUT_STATUS_IRQ)
+		panic("Watchdog pre-timeout IRQ");
+
+	return IRQ_NONE;
+}
+
 static int aspeed_wdt_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -253,6 +281,7 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
 	const char *reset_type;
 	u32 duration;
 	u32 status;
+	u32 timeout = 0;
 	int ret;
 
 	wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
@@ -291,6 +320,27 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
 	if (of_device_is_compatible(np, "aspeed,ast2400-wdt"))
 		wdt->ctrl = WDT_CTRL_1MHZ_CLK;
 
+	if (config->irq_mask) {
+		if (!of_property_read_u32(np, "aspeed,pre-timeout-irq-us", &timeout) && timeout) {
+			int irq =  platform_get_irq(pdev, 0);
+
+			if (irq < 0) {
+				dev_warn(dev, "Couldn't find IRQ: %d\n", irq);
+				timeout = 0;
+			} else {
+				ret = devm_request_irq(dev, irq, aspeed_wdt_irq, IRQF_SHARED,
+						       dev_name(dev), wdt);
+				if (ret) {
+					dev_warn(dev, "Couldn't request IRQ:%d\n", ret);
+					timeout = 0;
+				} else {
+					wdt->ctrl |= ((timeout << config->irq_shift) &
+						      config->irq_mask) | WDT_CTRL_WDT_INTR;
+				}
+			}
+		}
+	}
+
 	/*
 	 * Control reset on a per-device basis to ensure the
 	 * host is not affected by a BMC reboot
@@ -308,7 +358,7 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
 		else if (!strcmp(reset_type, "system"))
 			wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP |
 				     WDT_CTRL_RESET_SYSTEM;
-		else if (strcmp(reset_type, "none"))
+		else if (strcmp(reset_type, "none") && !timeout)
 			return -EINVAL;
 	}
 	if (of_property_read_bool(np, "aspeed,external-signal"))
Signature · 1 line
2.31.1
#2 lore raw

PATCH 2/3 ARM: dts: aspeed: Setup watchdog pre-timeout interrupt

In reply to Eddie James

Specify the interrupt lines for the base SOCs that support it.

---
 arch/arm/boot/dts/aspeed-g5.dtsi | 3 +++
 arch/arm/boot/dts/aspeed-g6.dtsi | 4 ++++
 2 files changed, 7 insertions(+)
arch/arm/boot/dts/aspeed-g5.dtsi +3 -0
index c89092c3905b..2ed19bb5710a 100644
@@ -402,18 +402,21 @@ wdt1: watchdog@1e785000 {
 				compatible = "aspeed,ast2500-wdt";
 				reg = <0x1e785000 0x20>;
 				clocks = <&syscon ASPEED_CLK_APB>;
+				interrupts = <27>;
 			};
 
 			wdt2: watchdog@1e785020 {
 				compatible = "aspeed,ast2500-wdt";
 				reg = <0x1e785020 0x20>;
 				clocks = <&syscon ASPEED_CLK_APB>;
+				interrupts = <27>;
 			};
 
 			wdt3: watchdog@1e785040 {
 				compatible = "aspeed,ast2500-wdt";
 				reg = <0x1e785040 0x20>;
 				clocks = <&syscon ASPEED_CLK_APB>;
+				interrupts = <27>;
 				status = "disabled";
 			};
 
arch/arm/boot/dts/aspeed-g6.dtsi +4 -0
index 1387a763a6a5..a9a53724f2af 100644
@@ -531,23 +531,27 @@ uart5: serial@1e784000 {
 
 			wdt1: watchdog@1e785000 {
 				compatible = "aspeed,ast2600-wdt";
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x1e785000 0x40>;
 			};
 
 			wdt2: watchdog@1e785040 {
 				compatible = "aspeed,ast2600-wdt";
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x1e785040 0x40>;
 				status = "disabled";
 			};
 
 			wdt3: watchdog@1e785080 {
 				compatible = "aspeed,ast2600-wdt";
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x1e785080 0x40>;
 				status = "disabled";
 			};
 
 			wdt4: watchdog@1e7850c0 {
 				compatible = "aspeed,ast2600-wdt";
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x1e7850C0 0x40>;
 				status = "disabled";
 			};
Signature · 1 line
2.31.1
#3 lore raw

PATCH 3/3 ARM: dts: aspeed: p10bmc: Set watchdog pre-timeout interrupt

In reply to Eddie James

Specify the pre-timeout interrupt time to enable the interrupt on P10 BMC systems.

---
 arch/arm/boot/dts/aspeed-bmc-ibm-bonnell.dts | 1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts | 1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 1 +
 3 files changed, 3 insertions(+)
arch/arm/boot/dts/aspeed-bmc-ibm-bonnell.dts +1 -0
index 6789c1ec286a..7acdda8791a0 100644
@@ -889,6 +889,7 @@ &wdt1 {
 };
 
 &wdt2 {
+	aspeed,pre-timeout-irq-us = <600000>;
 	status = "okay";
 };
 
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts +1 -0
index fcc890e3ad73..6d2e68e3fddf 100644
@@ -3653,6 +3653,7 @@ &wdt1 {
 };
 
 &wdt2 {
+	aspeed,pre-timeout-irq-us = <600000>;
 	status = "okay";
 };
 
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts +1 -0
index 4879da4cdbd2..8fd63df3959c 100644
@@ -2376,6 +2376,7 @@ &wdt1 {
 };
 
 &wdt2 {
+	aspeed,pre-timeout-irq-us = <600000>;
 	status = "okay";
 };
 
Signature · 1 line
2.31.1
maintainer
#4 lore raw
In reply to Eddie James

Hi Eddie,

Quoted 3 lines · Eddie James

Enable the watchdog pre-timeout interrupt if enabled in the device tree, and setup the relevant device trees.

Have you put this on the upstream lists too? (I'd recommend sending out the wdt change and the device tree updates can go in once you've got the .c change merged).

Cheers,

Joel

Quoted 17 lines

Eddie James (3):
watchdog: aspeed: Add pre-timeout interrupt support
ARM: dts: aspeed: Setup watchdog pre-timeout interrupt
ARM: dts: aspeed: p10bmc: Set watchdog pre-timeout interrupt

 arch/arm/boot/dts/aspeed-bmc-ibm-bonnell.dts |  1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts |  1 +
 arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts |  1 +
 arch/arm/boot/dts/aspeed-g5.dtsi             |  3 ++
 arch/arm/boot/dts/aspeed-g6.dtsi             |  4 ++
 drivers/watchdog/aspeed_wdt.c                | 54 +++++++++++++++++++-
 6 files changed, 62 insertions(+), 2 deletions(-)

--
2.31.1