imx8mm_evk: Add an entry for USB boot
Subsystems (2)
PATCH 1/2 imx8mm_evk: Add an entry for USB boot
Add an entry for USB boot so that U-Boot could be loaded via the Serial Download Protocol.
--- board/freescale/imx8mm_evk/spl.c | 2 ++ 1 file changed, 2 insertions(+)
board/freescale/imx8mm_evk/spl.c +2 -0
@@ -33,6 +33,8 @@ DECLARE_GLOBAL_DATA_PTR;int spl_board_boot_device (enum boot_device boot_dev_spl) {switch (boot_dev_spl) { +case USB_BOOT : +return BOOT_DEVICE_BOARD ;case SD2_BOOT :case MMC2_BOOT :return BOOT_DEVICE_MMC1 ;
Signature · 1 line
2.25.1
PATCH 2/2 imx8mm_evk: Add Serial Download Protocol support
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO to reduce its size.
--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)
arch/arm/dts/imx8mm-evk-u-boot.dtsi +16 -0
@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };
@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };
configs/imx8mm_evk_defconfig +21 -0
@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000
@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048
@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y
@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y
@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y
Signature · 1 line
2.25.1
Re: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
Hi
Quoted 59 lines · Fabio Estevam
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
$ uuu -brun spl flash.binBased on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select
CONFIG_LTOto reduce its size.Signed-off-by Fabio Estevam <[email protected]>--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)arch/arm/dts/imx8mm-evk-u-boot.dtsi +16
-0@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };configs/imx8mm_evk_defconfig +0
-0
configs/imx8mm_evk_defconfig CONFIG_SPL_SERIAL=y · line 20
Quoted 4 lines
configs/imx8mm_evk_defconfig +1
-0@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=y
Is the entry required? or part of the series. If so could you explain in the commit message?
Michael
Quoted 55 lines
configs/imx8mm_evk_defconfig +20
-1CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y --2.25.1
Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com
RE: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
Hello Michael,
Quoted 70 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Michael Nazzareno Trimarchi
Sent: Tuesday, September 20, 2022 7:46 AM
To: Fabio Estevam <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH 2/2]imx8mm_evk: Add Serial Download Protocol supportHi
arch/arm/dts/imx8mm-evk-u-
Quoted 21 lines · Fabio Estevam
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
$ uuu -brun spl flash.binBased on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select
CONFIG_LTOto reduce its size.Signed-off-by Fabio Estevam <[email protected]>--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)arch/arm/dts/imx8mm-evk-u- renamed from arch/arm/dts/imx8mm-evk-u-boot.dtsi +0
-0
boot.dtsiQuoted 37 lines
index
36fbf56bc5..d82428f8fe100644arch/arm/dts/imx8mm-evk-u-boot.dtsi +16
-0@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };configs/imx8mm_evk_defconfig +0
-0
Quoted 8 lines
configs/imx8mm_evk_defconfig CONFIG_SPL_SERIAL=y · line 20
Quoted 5 lines
configs/imx8mm_evk_defconfig +1
-0@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=yIs the entry required? or part of the series. If so could you explain in the commit message?
While not being strictly part of the series, Fabio did explained the LTO enablement in the commit message above. This reduces the size of SPL, which in turn allows it to fit into IRAM.
-- andrey
Quoted 72 lines
Michael
Quoted 53 lines
configs/imx8mm_evk_defconfig +20
-1CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y --Quoted 2 lines
2.25.1
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
[email protected]
__________________________________Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
[email protected]
www.amarulasolutions.com
Re: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
HI
Quoted 82 lines · ZHIZHIKIN Andrey
Hello Michael,
Quoted 70 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Michael Nazzareno Trimarchi
Sent: Tuesday, September 20, 2022 7:46 AM
To: Fabio Estevam <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH 2/2]imx8mm_evk: Add Serial Download Protocol supportHi
arch/arm/dts/imx8mm-evk-u-
Quoted 21 lines · Fabio Estevam
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
$ uuu -brun spl flash.binBased on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select
CONFIG_LTOto reduce its size.Signed-off-by Fabio Estevam <[email protected]>--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)arch/arm/dts/imx8mm-evk-u- renamed from arch/arm/dts/imx8mm-evk-u-boot.dtsi +0
-0
boot.dtsiQuoted 37 lines
index
36fbf56bc5..d82428f8fe100644arch/arm/dts/imx8mm-evk-u-boot.dtsi +16
-0@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };configs/imx8mm_evk_defconfig +0
-0Quoted 8 lines
configs/imx8mm_evk_defconfig CONFIG_SPL_SERIAL=y · line 20
Quoted 5 lines
configs/imx8mm_evk_defconfig +1
-0@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=yIs the entry required? or part of the series. If so could you explain in the commit message?
Quoted 4 lines
While not being strictly part of the series, Fabio did explained the LTO enablement in the commit message above. This reduces the size of SPL, which in turn allows it to fit into IRAM.
Sorry too early. I was thinking that I was read this comment in marek review for other patch but was reported even here
Michael
Quoted 74 lines
-- andrey
Quoted 72 lines
Michael
Quoted 53 lines
configs/imx8mm_evk_defconfig +20
-1CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y --Quoted 2 lines
2.25.1
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
[email protected]
__________________________________Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
[email protected]
www.amarulasolutions.com
Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com
Re: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
In reply to Fabio EstevamHi Fabio,
Just have a question, the tcpci driver is not supported, so how do you manage to make SDP work?
Regards,
Peng.
Quoted 114 lines · Fabio Estevam
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
$ uuu -brun spl flash.binBased on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select
CONFIG_LTOto reduce its size.Signed-off-by Fabio Estevam <[email protected]>--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)arch/arm/dts/imx8mm-evk-u-boot.dtsi +16
-0@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };configs/imx8mm_evk_defconfig +21
-0@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y
Fabio Estevam
reviewerRe: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
Hi Peng,
Quoted 5 lines · Peng Fan
Hi Fabio,
Just have a question, the tcpci driver is not supported, so how do you manage to make SDP work?
I understand that the tcpci driver is required when a USB role switch is needed.
I am only using the usbotg1 as a peripheral.
Here are the logs:
On the host PC:
$ sudo uuu -brun spl flash.bin
On the console:
U-Boot SPL 2022.10-rc5-00003-g9e02955991-dirty (Sep 19 2022 - 21:49:01 -0300) No pmic
SEC0: RNG instantiated
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 885712 to 0x40400000... done
Jumping to header at 0x40400000
Header Tag is not an IMX image
Found header at 0x40420400
NOTICE: BL31: v2.2(release):rel_imx_5.4.47_2.2.0-0-gc949a888e NOTICE: BL31: Built : 17:18:02, Sep 19 2022
U-Boot 2022.10-rc5-00003-g9e02955991-dirty (Sep 19 2022 - 21:49:01 -0300)
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: FSL i.MX8MM EVK board DRAM: 2 GiB Core: 176 devices, 23 uclasses, devicetree: separate WDT: Started watchdog@30280000 with servicing (60s timeout) MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@30890000 Out: serial@30890000 Err: serial@30890000 SEC0: RNG instantiated Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0
u-boot=>
One issue that I observed and haven't had a chance to debug yet is that running 'ums 0 mmc 1' works only when issued for the first time.
If I interrupt with CRLC+C and then launch 'ums 0 mmc 1' again, it does not work.
This is unrelated to SDP and happens when I boot from SD card as well.
If you have any ideas, please let me know.
Thanks,
Fabio Estevam
Re: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
Quoted 4 lines · Fabio Estevam
Hi Peng,
Quoted 1 line · Peng Fan
Quoted 8 lines
Quoted 4 lines
Hi Fabio,
Just have a question, the tcpci driver is not supported, so how do you manage to make SDP work?
I understand that the tcpci driver is required when a USB role switch is needed.
I am only using the usbotg1 as a peripheral.
ok, got it.
Quoted 46 lines
Here are the logs:
On the host PC:
$ sudo uuu -brun spl flash.binOn the console:
U-Boot SPL 2022.10-rc5-00003-g9e02955991-dirty (Sep 19 2022 - 21:49:01 -0300) No pmic
SEC0: RNG instantiated
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from USB SDP
SDP: initialize...
SDP: handle requests...
Downloading file of size 885712 to0x40400000... done
Jumping to header at0x40400000
Header Tag is not an IMX image
Found header at0x40420400NOTICE: BL31: v2.2(release):rel_imx_5.4.47_2.2.0-0-gc949a888e NOTICE: BL31: Built : 17:18:02, Sep 19 2022U-Boot 2022.10-rc5-00003-g9e02955991-dirty (Sep 19 2022 - 21:49:01 -0300)
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: FSL i.MX8MM EVK board DRAM: 2 GiB Core: 176 devices, 23 uclasses, devicetree: separate WDT: Started watchdog@30280000 with servicing (60s timeout) MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@30890000 Out: serial@30890000 Err: serial@30890000 SEC0: RNG instantiated Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0u-boot=>
One issue that I observed and haven't had a chance to debug yet is that running 'ums 0 mmc 1' works only when issued for the first time.
Quoted 6 lines
If I interrupt with CRLC+C and then launch 'ums 0 mmc 1' again, it does not work.
This is unrelated to SDP and happens when I boot from SD card as well.
If you have any ideas, please let me know.
I am not sure, the master branch has this issue? Any specific config option required?
Thanks,
Peng.
Quoted 4 lines
Thanks,
Fabio Estevam
Fabio Estevam
reviewerRe: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
Hi Peng,
Quoted 2 lines · Peng Fan
I am not sure, the master branch has this issue? Any specific config option required?
Yes, to reproduce this issue on U-Boot master, just need to apply this series plus Marek's fix:
https://lore.kernel.org/u-boot/CAOMZO5Cid5eck=ahiowbAKOjaQNzOORNLU-PxadkMFSEnqvNmg@mail.gmail.com/T/#t
It looks like some clock-related issue:
u-boot=> ums 0 mmc 1
UMS: LUN 0, dev mmc 1, hwpart 0, sector 0x0, count 0x3b72400 CTRL+C - Operation aborted
clk usb_bus already disabled
After issuing CTRL+C, dmesg on the host PC shows lots of USB failures.
If you have any suggestions, please let me know.
Thanks
Re: [PATCH 2/2] imx8mm_evk: Add Serial Download Protocol support
In reply to Fabio EstevamQuoted 6 lines · Fabio Estevam
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:
Quoted 8 lines
$ uuu -brun spl flash.binBased on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select
CONFIG_LTOto reduce its size.Signed-off-by Fabio Estevam <[email protected]>
Quoted 100 lines
--- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 16 ++++++++++++++++ configs/imx8mm_evk_defconfig | 21 +++++++++++++++++++++ 2 files changed, 37 insertions(+)arch/arm/dts/imx8mm-evk-u-boot.dtsi +16
-0@@ -20,6 +20,10 @@ }; }; +&aips4 { + u-boot,dm-spl; +}; + ®_usdhc2_vmmc { u-boot,off-on-delay-us = <20000>; };@@ -84,6 +88,18 @@ u-boot,dm-spl; }; +&usbmisc1 { + u-boot,dm-spl; +}; + +&usbphynop1 { + u-boot,dm-spl; +}; + +&usbotg1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };configs/imx8mm_evk_defconfig +21
-0@@ -17,6 +17,7 @@ CONFIG_SPL_SERIAL=y CONFIG_SPL_DRIVERS_MISC=y CONFIG_SPL=y CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_LTO=y CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000@@ -38,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C=y CONFIG_SPL_POWER=y +CONFIG_SPL_USB_HOST=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y CONFIG_SPL_WATCHDOG=y CONFIG_SYS_MAXARGS=64 CONFIG_SYS_CBSIZE=2048@@ -50,6 +54,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y@@ -80,9 +86,13 @@ CONFIG_PHY_ATHEROS=y CONFIG_PHY_GIGE=y CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_SPL_PHY=y +CONFIG_SPL_NOP_PHY=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y CONFIG_DM_PMIC=y CONFIG_SPL_DM_PMIC_PCA9450=y CONFIG_DM_REGULATOR=y@@ -97,4 +107,15 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +# CONFIG_USB_STORAGE is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x40400000 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y
PATCH 2/2 imx8mm_evk: Add Serial Download Protocol support
In reply to Fabio EstevamQuoted 10 lines
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command:$ uuu -brun spl flash.bin Based on a patch from Marek Vasut for the imx8mm-mx8menlo board. Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO to reduce its size. Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Peng Fan <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Quoted 4 lines · Fabio Estevam
Add an entry for USB boot so that U-Boot could be loaded via the Serial Download Protocol.
Signed-off-by Fabio Estevam <[email protected]>
Quoted 17 lines
--- board/freescale/imx8mm_evk/spl.c | 2 ++ 1 file changed, 2 insertions(+)board/freescale/imx8mm_evk/spl.c +2
-0@@ -33,6 +33,8 @@ DECLARE_GLOBAL_DATA_PTR;int spl_board_boot_device (enum boot_device boot_dev_spl) {switch (boot_dev_spl) { +case USB_BOOT : +return BOOT_DEVICE_BOARD ;case SD2_BOOT :case MMC2_BOOT :return BOOT_DEVICE_MMC1 ;
PATCH 1/2 imx8mm_evk: Add an entry for USB boot
In reply to Fabio EstevamQuoted 4 lines
Add an entry for USB boot so that U-Boot could be loaded via the Serial Download Protocol.
Signed-off-by Fabio Estevam <[email protected]>Reviewed-by Peng Fan <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================