Skip to contentSkip to conversation

arm: dts: Create common imx8mn-u-boot

PATCH New Adam Ford 2 participants 15 messages Oct 22, 2022 – Oct 24, 2022

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

v2 cover arm: dts: Create common imx8mn-u-boot

Every imx8mn board has a bunch of similar entries on their respective board-u-boot.dtsi file to make the board bootable. Instead of maintaining multiple files with duplicate code, have them all point to a new, common file. This file includes the necessary nodes that were common to nearly all boards and added spba1 to help faciliate SPL_DM_SERIAL. This also adds support for CONFIG_FSPI_CONF_HEADER which can be used to generate flash.bin files for booting from FlexSPI.

Adam Ford (7):
arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi
arm: dts: imx8mn-beacon-kit: Consolidate with imx8mn-u-boot
arm: dts: imx8mn-bsh-smm-s2: Consolidate with imx8mn-u-boot
arm: dts: imx8mn-ddr4-evk: Consolidate with imx8mn-u-boot
arm: dts: imx8mn-evk: Consolidate with imx8mn-u-boot
arm: dts: imx8mn-var-som-symphony: Consolidate with imx8mn-u-boot
arm: dts: imx8mn-venice: Consolidate with imx8mn-u-boot

For the series:

 arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi    | 180 +------------
 .../dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi  | 172 +-----------
 arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi      | 188 +------------
 arch/arm/dts/imx8mn-evk-u-boot.dtsi           | 108 --------
 arch/arm/dts/imx8mn-u-boot.dtsi               | 248 ++++++++++++++++++
 .../dts/imx8mn-var-som-symphony-u-boot.dtsi   | 188 +------------
 arch/arm/dts/imx8mn-venice-u-boot.dtsi        | 196 +-------------
 7 files changed, 254 insertions(+), 1026 deletions(-)
 create mode 100644 arch/arm/dts/imx8mn-u-boot.dtsi
Signature · 1 line
2.34.1
author
#1 lore raw

PATCH v2 1/7 arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi

Multiple boards create duplicate entries in their respective -u-boot.dtsi files which all basically do the same thing. To consolidate these and make it easier to make improvements going forward, consolidate them all into one place.

This file creates a flash.bin image using binman, and supports LPDDR4, DDR4 and DDR3. Since individual boards use different peripherals and different UART ports, those entries were kept in their respective board files, but the spba1 node was addded which contains all UART1-3 to help facilitate SPL_DM_SERIAL. Individual users will still need to include their respective UART and pinctrl nodes for those UARTS.

This consolidated file also supports generating a flash.bin file which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is enabled.

arch/arm/dts/imx8mn-u-boot.dtsi new file +248 -0
new file mode 100644
index 0000000000..327d4070fc
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks
+ */
+
+/ {
+	binman: binman {
+		multiple-images;
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	wdt-reboot {
+		compatible = "wdt-reboot";
+		wdt = <&wdog1>;
+		u-boot,dm-spl;
+	};
+};
+
+&{/soc@0} {
+	u-boot,dm-pre-reloc;
+	u-boot,dm-spl;
+};
+
+&aips1 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+	u-boot,dm-spl;
+};
+
+&aips3 {
+	u-boot,dm-spl;
+};
+
+&aips4 {
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+	/delete-property/ assigned-clocks;
+	/delete-property/ assigned-clock-parents;
+	/delete-property/ assigned-clock-rates;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&osc_24m {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&spba1 {
+	u-boot,dm-spl;
+};
+
+&wdog1 {
+	u-boot,dm-spl;
+};
+
+&binman {
+	 u-boot-spl-ddr {
+		filename = "u-boot-spl-ddr.bin";
+		pad-byte = <0xff>;
+		align-size = <4>;
+		align = <4>;
+
+		u-boot-spl {
+			align-end = <4>;
+			filename = "u-boot-spl.bin";
+		};
+
+		ddr-1d-imem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_1d_imem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_imem_1d.bin";
+#else
+			filename = "ddr3_imem_1d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-1d-dmem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_1d_dmem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_dmem_1d.bin";
+#else
+			filename = "ddr3_dmem_1d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-2d-imem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_2d_imem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_imem_2d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-2d-dmem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_2d_dmem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_dmem_2d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
+
+			blob {
+				filename = "u-boot-spl-ddr.bin";
+			};
+		};
+	};
+
+	itb {
+		filename = "u-boot.itb";
+
+		fit {
+			description = "Configuration to load ATF before U-Boot";
+			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+			fit,fdt-list = "of-list";
+			#address-cells = <1>;
+
+			images {
+				uboot {
+					arch = "arm64";
+					compression = "none";
+					description = "U-Boot (64-bit)";
+					load = <CONFIG_SYS_TEXT_BASE>;
+					type = "standalone";
+
+					uboot-blob {
+						filename = "u-boot-nodtb.bin";
+						type = "blob-ext";
+					};
+				};
+
+				atf {
+					arch = "arm64";
+					compression = "none";
+					description = "ARM Trusted Firmware";
+					entry = <0x960000>;
+					load = <0x960000>;
+					type = "firmware";
+
+					atf-blob {
+						filename = "bl31.bin";
+						type = "atf-bl31";
+					};
+				};
+
+				binman_fip: fip {
+					arch = "arm64";
+					compression = "none";
+					description = "Trusted Firmware FIP";
+					load = <0x40310000>;
+					type = "firmware";
+				};
+
+				@fdt-SEQ {
+					compression = "none";
+					description = "NAME";
+					type = "flat_dt";
+
+					uboot-fdt-blob {
+						filename = "u-boot.dtb";
+						type = "blob-ext";
+					};
+				};
+			};
+
+			configurations {
+				default = "@config-DEFAULT-SEQ";
+
+				binman_configuration: @config-SEQ {
+					description = "NAME";
+					fdt = "fdt-SEQ";
+					firmware = "uboot";
+					loadables = "atf";
+				};
+			};
+		};
+	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+#ifdef CONFIG_FSPI_CONF_HEADER
+		fspi_conf_block {
+			filename = CONFIG_FSPI_CONF_FILE;
+			type = "blob-ext";
+			offset = <0x400>;
+		};
+
+		spl {
+			filename = "spl.bin";
+			offset = <0x1000>;
+			type = "blob-ext";
+		};
+
+		binman_uboot: uboot {
+			filename = "u-boot.itb";
+			offset = <0x59000>;
+			type = "blob-ext";
+		};
+#else
+
+		spl {
+			offset = <0x0>;
+			filename = "spl.bin";
+			type = "blob-ext";
+		};
+
+		binman_uboot: uboot {
+			offset = <0x58000>;
+			filename = "u-boot.itb";
+			type = "blob-ext";
+		};
+#endif
+	};
+};
Signature · 1 line
2.34.1
#2 lore raw

PATCH v2 1/7 arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi

Quoted 260 lines

Multiple boards create duplicate entries in their respective -u-boot.dtsi files which all basically do the same thing. To consolidate these and make it easier to make improvements going forward, consolidate them all into one place. This file creates a flash.bin image using binman, and supports LPDDR4, DDR4 and DDR3. Since individual boards use different peripherals and different UART ports, those entries were kept in their respective board files, but the spba1 node was addded which contains all UART1-3 to help facilitate SPL_DM_SERIAL. Individual users will still need to include their respective UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is enabled.

arch/arm/dts/imx8mn-u-boot.dtsi new file +238 -0
new file mode 100644
index 0000000000..327d4070fc
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks
+ */
+
+/ {
+	binman: binman {
+		multiple-images;
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	wdt-reboot {
+		compatible = "wdt-reboot";
+		wdt = <&wdog1>;
+		u-boot,dm-spl;
+	};
+};
+
+&{/soc@0} {
+	u-boot,dm-pre-reloc;
+	u-boot,dm-spl;
+};
+
+&aips1 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+	u-boot,dm-spl;
+};
+
+&aips3 {
+	u-boot,dm-spl;
+};
+
+&aips4 {
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+	/delete-property/ assigned-clocks;
+	/delete-property/ assigned-clock-parents;
+	/delete-property/ assigned-clock-rates;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&osc_24m {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&spba1 {
+	u-boot,dm-spl;
+};
+
+&wdog1 {
+	u-boot,dm-spl;
+};
+
+&binman {
+	 u-boot-spl-ddr {
+		filename = "u-boot-spl-ddr.bin";
+		pad-byte = <0xff>;
+		align-size = <4>;
+		align = <4>;
+
+		u-boot-spl {
+			align-end = <4>;
+			filename = "u-boot-spl.bin";
+		};
+
+		ddr-1d-imem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_1d_imem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_imem_1d.bin";
+#else
+			filename = "ddr3_imem_1d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-1d-dmem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_1d_dmem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_dmem_1d.bin";
+#else
+			filename = "ddr3_dmem_1d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-2d-imem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_2d_imem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_imem_2d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+
+		ddr-2d-dmem-fw {
+#ifdef CONFIG_IMX8M_LPDDR4
+			filename = "lpddr4_pmu_train_2d_dmem.bin";
+#elif CONFIG_IMX8M_DDR4
+			filename = "ddr4_dmem_2d.bin";
+#endif
+			type = "blob-ext";
+			align-end = <4>;
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
+
+			blob {
+				filename = "u-boot-spl-ddr.bin";
+			};
+		};
+	};
+
+	itb {
+		filename = "u-boot.itb";
+
+		fit {
+			description = "Configuration to load ATF before U-Boot";
+			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+			fit,fdt-list = "of-list";
+			#address-cells = <1>;
+
+			images {
+				uboot {
+					arch = "arm64";
+					compression = "none";
+					description = "U-Boot (64-bit)";
+					load = <CONFIG_SYS_TEXT_BASE>;
+					type = "standalone";
+
+					uboot-blob {
+						filename = "u-boot-nodtb.bin";
+						type = "blob-ext";
+					};
+				};
+
+				atf {
+					arch = "arm64";
+					compression = "none";
+					description = "ARM Trusted Firmware";
+					entry = <0x960000>;
+					load = <0x960000>;
+					type = "firmware";
+
+					atf-blob {
+						filename = "bl31.bin";
+						type = "atf-bl31";
+					};
+				};
+
+				binman_fip: fip {
+					arch = "arm64";
+					compression = "none";
+					description = "Trusted Firmware FIP";
+					load = <0x40310000>;
+					type = "firmware";
+				};
+
+				@fdt-SEQ {
+					compression = "none";
+					description = "NAME";
+					type = "flat_dt";
+
+					uboot-fdt-blob {
+						filename = "u-boot.dtb";
+						type = "blob-ext";
+					};
+				};
+			};
+
+			configurations {
+				default = "@config-DEFAULT-SEQ";
+
+				binman_configuration: @config-SEQ {
+					description = "NAME";
+					fdt = "fdt-SEQ";
+					firmware = "uboot";
+					loadables = "atf";
+				};
+			};
+		};
+	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+#ifdef CONFIG_FSPI_CONF_HEADER
+		fspi_conf_block {
+			filename = CONFIG_FSPI_CONF_FILE;
+			type = "blob-ext";
+			offset = <0x400>;
+		};
+
+		spl {
+			filename = "spl.bin";
+			offset = <0x1000>;
+			type = "blob-ext";
+		};
+
+		binman_uboot: uboot {
+			filename = "u-boot.itb";
+			offset = <0x59000>;
+			type = "blob-ext";
+		};
+#else
+
+		spl {
+			offset = <0x0>;
+			filename = "spl.bin";
+			type = "blob-ext";

arch/arm/dts/imx8mn-u-boot.dtsi line 248

Quoted 10 lines
arch/arm/dts/imx8mn-u-boot.dtsi new file +10 -0
+		};
+
+		binman_uboot: uboot {
+			offset = <0x58000>;
+			filename = "u-boot.itb";
+			type = "blob-ext";
+		};
+#endif
+	};
+};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#3 lore raw

PATCH v2 2/7 arm: dts: imx8mn-beacon-kit: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi +2 -178
index 0efa6862eb..3180d57239 100644
@@ -1,24 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright 2020 Compass Electronics Group, LLC
+ * Copyright 2022 Logic PD, Inc. dba Beacon EmbeddedWorks
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -28,27 +13,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -61,15 +25,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
 &pca6416_0 {
 	compatible = "ti,tca6416";
 };
@@ -106,10 +61,6 @@
 	u-boot,off-on-delay-us = <20000>;
 };
 
-&spba1 {
-	u-boot,dm-spl;
-};
-
 &uart2 {
 	u-boot,dm-spl;
 };
@@ -132,133 +83,6 @@
 	mmc-hs400-enhanced-strobe;
 };
 
-&wdog1 {
-	u-boot,dm-spl;
-};
-
 &pinctrl_wdog {
 	u-boot,dm-spl;
 };
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl: blob-ext@1 {
-			offset = <0x0>;
-			filename = "spl.bin";
-		};
-
-		uboot: blob-ext@2 {
-			offset = <0x58000>;
-			filename = "u-boot.itb";
-		};
-	};
-};
Signature · 1 line
2.34.1
#4 lore raw

PATCH v2 2/7 arm: dts: imx8mn-beacon-kit: Consolidate with imx8mn-u-boot

Quoted 213 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi +2 -168
index 0efa6862eb..3180d57239 100644
@@ -1,24 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright 2020 Compass Electronics Group, LLC
+ * Copyright 2022 Logic PD, Inc. dba Beacon EmbeddedWorks
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -28,27 +13,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -61,15 +25,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
 &pca6416_0 {
 	compatible = "ti,tca6416";
 };
@@ -106,10 +61,6 @@
 	u-boot,off-on-delay-us = <20000>;
 };
 
-&spba1 {
-	u-boot,dm-spl;
-};
-
 &uart2 {
 	u-boot,dm-spl;
 };
@@ -132,133 +83,6 @@
 	mmc-hs400-enhanced-strobe;
 };
 
-&wdog1 {
-	u-boot,dm-spl;
-};
-
 &pinctrl_wdog {
 	u-boot,dm-spl;
 };
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl: blob-ext@1 {

arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi line 264

Quoted 10 lines
arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi +0 -10
-			offset = <0x0>;
-			filename = "spl.bin";
-		};
-
-		uboot: blob-ext@2 {
-			offset = <0x58000>;
-			filename = "u-boot.itb";
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#5 lore raw

PATCH v2 3/7 arm: dts: imx8mn-bsh-smm-s2: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi +1 -171
index c4ae7ca4f3..3967e0bd15 100644
@@ -4,22 +4,7 @@
  * Copyright 2021 BSH Hausgeraete GmbH
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -29,27 +14,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&aips4 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -66,15 +30,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
 &pinctrl_i2c1 {
 	u-boot,dm-spl;
 };
@@ -98,128 +53,3 @@
 &wdog1 {
 	u-boot,dm-spl;
 };
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr3_imem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr3_dmem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "atf-bl31";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};
Signature · 1 line
2.34.1
#6 lore raw

PATCH v2 3/7 arm: dts: imx8mn-bsh-smm-s2: Consolidate with imx8mn-u-boot

Quoted 194 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi +1 -161
index c4ae7ca4f3..3967e0bd15 100644
@@ -4,22 +4,7 @@
  * Copyright 2021 BSH Hausgeraete GmbH
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -29,27 +14,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&aips4 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -66,15 +30,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
 &pinctrl_i2c1 {
 	u-boot,dm-spl;
 };
@@ -98,128 +53,3 @@
 &wdog1 {
 	u-boot,dm-spl;
 };
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr3_imem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr3_dmem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "atf-bl31";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;

arch/arm/dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi line 225

Quoted 10 lines
arch/arm/dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi +0 -10
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#7 lore raw

PATCH v2 4/7 arm: dts: imx8mn-ddr4-evk: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi +1 -187
index 3fdb20cb35..54f3ebe88b 100644
@@ -3,66 +3,7 @@
  * Copyright 2019, 2021 NXP
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-	firmware {
-		optee {
-			compatible = "linaro,optee-tz";
-			method = "smc";
-		};
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&iomuxc {
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &pinctrl_reg_usdhc2_vmmc {
 	u-boot,dm-spl;
@@ -147,130 +88,3 @@
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
 };
-
-&wdog1 {
-	u-boot,dm-spl;
-};
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr4_imem_1d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr4_dmem_1d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "ddr4_imem_2d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "ddr4_dmem_2d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl: blob-ext@1 {
-			offset = <0x0>;
-			filename = "spl.bin";
-		};
-
-		uboot: blob-ext@2 {
-			offset = <0x58000>;
-			filename = "u-boot.itb";
-		};
-	};
-};
Signature · 1 line
2.34.1
#8 lore raw

PATCH v2 4/7 arm: dts: imx8mn-ddr4-evk: Consolidate with imx8mn-u-boot

Quoted 196 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi +1 -177
index 3fdb20cb35..54f3ebe88b 100644
@@ -3,66 +3,7 @@
  * Copyright 2019, 2021 NXP
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-	firmware {
-		optee {
-			compatible = "linaro,optee-tz";
-			method = "smc";
-		};
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&iomuxc {
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &pinctrl_reg_usdhc2_vmmc {
 	u-boot,dm-spl;
@@ -147,130 +88,3 @@
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
 };
-
-&wdog1 {
-	u-boot,dm-spl;
-};
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr4_imem_1d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr4_dmem_1d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "ddr4_imem_2d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "ddr4_dmem_2d_201810.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl: blob-ext@1 {

arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi line 276

Quoted 10 lines
arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi +0 -10
-			offset = <0x0>;
-			filename = "spl.bin";
-		};
-
-		uboot: blob-ext@2 {
-			offset = <0x58000>;
-			filename = "u-boot.itb";
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#9 lore raw

PATCH v2 5/7 arm: dts: imx8mn-evk: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-evk-u-boot.dtsi +0 -108
index c4b83d3f7e..6c6c949f43 100644
@@ -24,111 +24,3 @@
 &pinctrl_pmic {
 	u-boot,dm-spl;
 };
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-};
Signature · 1 line
2.34.1
#10 lore raw

PATCH v2 5/7 arm: dts: imx8mn-evk: Consolidate with imx8mn-u-boot

Quoted 109 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-evk-u-boot.dtsi +0 -98
index c4b83d3f7e..6c6c949f43 100644
@@ -24,111 +24,3 @@
 &pinctrl_pmic {
 	u-boot,dm-spl;
 };
-
-&binman {
-	 u-boot-spl-ddr {
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-		align-size = <4>;
-		align = <4>;
-
-		u-boot-spl {
-			align-end = <4>;
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			type = "blob-ext";
-			align-end = <4>;
-		};
-	};
-
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			#address-cells = <1>;
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
-			images {
-				uboot {
-					description = "U-Boot (64-bit)";
-					type = "standalone";
-					arch = "arm64";
-					compression = "none";
-					load = <CONFIG_SYS_TEXT_BASE>;
-
-					uboot_blob: blob-ext {
-						filename = "u-boot-nodtb.bin";
-					};
-				};
-
-				atf {
-					description = "ARM Trusted Firmware";
-					type = "firmware";
-					arch = "arm64";
-					compression = "none";
-					load = <0x960000>;
-					entry = <0x960000>;
-
-					atf_blob: blob-ext {
-						filename = "bl31.bin";
-					};
-				};
-
-				fdt {
-					description = "NAME";
-					type = "flat_dt";
-					compression = "none";
-
-					uboot_fdt_blob: blob-ext {
-						filename = "u-boot.dtb";
-					};
-				};
-			};
-
-			configurations {
-				default = "conf";
-

arch/arm/dts/imx8mn-evk-u-boot.dtsi line 134

Quoted 10 lines
arch/arm/dts/imx8mn-evk-u-boot.dtsi +0 -10
-				conf {
-					description = "NAME";
-					firmware = "uboot";
-					loadables = "atf";
-					fdt = "fdt";
-				};
-			};
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#11 lore raw

PATCH v2 6/7 arm: dts: imx8mn-var-som-symphony: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-var-som-symphony-u-boot.dtsi +1 -187
index ed1ab10ded..a20683155c 100644
@@ -3,22 +3,7 @@
  * Copyright 2021 Collabora Ltd.
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -28,27 +13,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&aips4 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -65,15 +29,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
 &pinctrl_i2c1 {
 	u-boot,dm-spl;
 };
@@ -113,144 +68,3 @@
 &usdhc3 {
 	u-boot,dm-spl;
 };
-
-&wdog1 {
-	u-boot,dm-spl;
-};
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr4_imem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr4_dmem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-imem-fw {
-			filename = "ddr4_imem_2d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "ddr4_dmem_2d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "atf-bl31";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};
Signature · 1 line
2.34.1
#12 lore raw

PATCH v2 6/7 arm: dts: imx8mn-var-som-symphony: Consolidate with imx8mn-u-boot

Quoted 210 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-var-som-symphony-u-boot.dtsi +1 -177
index ed1ab10ded..a20683155c 100644
@@ -3,22 +3,7 @@
  * Copyright 2021 Collabora Ltd.
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
 	u-boot,dm-spl;
@@ -28,27 +13,6 @@
 	u-boot,dm-spl;
 };
 
-&aips1 {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&aips4 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
 &gpio1 {
 	u-boot,dm-spl;
 };
@@ -65,15 +29,6 @@
 	u-boot,dm-spl;
 };
 
-&iomuxc {
-	u-boot,dm-spl;
-};
-
-&osc_24m {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
 &pinctrl_i2c1 {
 	u-boot,dm-spl;
 };
@@ -113,144 +68,3 @@
 &usdhc3 {
 	u-boot,dm-spl;
 };
-
-&wdog1 {
-	u-boot,dm-spl;
-};
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "ddr4_imem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "ddr4_dmem_1d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-imem-fw {
-			filename = "ddr4_imem_2d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "ddr4_dmem_2d.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "atf-bl31";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;

arch/arm/dts/imx8mn-var-som-symphony-u-boot.dtsi line 256

Quoted 10 lines
arch/arm/dts/imx8mn-var-som-symphony-u-boot.dtsi +0 -10
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#13 lore raw

PATCH v2 7/7 arm: dts: imx8mn-venice: Consolidate with imx8mn-u-boot

In reply to Adam Ford

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-venice-u-boot.dtsi +1 -195
index 42e4d935cf..aea48f2d79 100644
@@ -3,60 +3,7 @@
  * Copyright 2022 Gateworks Corporation
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&iomuxc {
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &gpio1 {
 	u-boot,dm-spl;
@@ -114,147 +61,6 @@
 	u-boot,dm-spl;
 };
 
-&wdog1 {
-	u-boot,dm-spl;
-};
-
 &pinctrl_wdog {
 	u-boot,dm-spl;
 };
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "blob-ext";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};
Signature · 1 line
2.34.1
#14 lore raw

PATCH v2 7/7 arm: dts: imx8mn-venice: Consolidate with imx8mn-u-boot

Quoted 207 lines

Now that a unified imx8mn-u-boot is available, remove duplicated code for generating flash.bin and other common imx8mn peripherals.

arch/arm/dts/imx8mn-venice-u-boot.dtsi +1 -185
index 42e4d935cf..aea48f2d79 100644
@@ -3,60 +3,7 @@
  * Copyright 2022 Gateworks Corporation
  */
 
-/ {
-	binman: binman {
-		multiple-images;
-	};
-
-	wdt-reboot {
-		compatible = "wdt-reboot";
-		wdt = <&wdog1>;
-		u-boot,dm-spl;
-	};
-};
-
-&{/soc@0} {
-	u-boot,dm-pre-reloc;
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&spba1 {
-	u-boot,dm-spl;
-};
-
-&clk {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-	/delete-property/ assigned-clocks;
-	/delete-property/ assigned-clock-parents;
-	/delete-property/ assigned-clock-rates;
-};
-
-&osc_24m {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips1 {
-	u-boot,dm-spl;
-	u-boot,dm-pre-reloc;
-};
-
-&aips2 {
-	u-boot,dm-spl;
-};
-
-&aips3 {
-	u-boot,dm-spl;
-};
-
-&iomuxc {
-	u-boot,dm-spl;
-};
+#include "imx8mn-u-boot.dtsi"
 
 &gpio1 {
 	u-boot,dm-spl;
@@ -114,147 +61,6 @@
 	u-boot,dm-spl;
 };
 
-&wdog1 {
-	u-boot,dm-spl;
-};
-
 &pinctrl_wdog {
 	u-boot,dm-spl;
 };
-
-&binman {
-	u-boot-spl-ddr {
-		align = <4>;
-		align-size = <4>;
-		filename = "u-boot-spl-ddr.bin";
-		pad-byte = <0xff>;
-
-		u-boot-spl {
-			align-end = <4>;
-			filename = "u-boot-spl.bin";
-		};
-
-		ddr-1d-imem-fw {
-			filename = "lpddr4_pmu_train_1d_imem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-1d-dmem-fw {
-			filename = "lpddr4_pmu_train_1d_dmem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-imem-fw {
-			filename = "lpddr4_pmu_train_2d_imem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-
-		ddr-2d-dmem-fw {
-			filename = "lpddr4_pmu_train_2d_dmem.bin";
-			align-end = <4>;
-			type = "blob-ext";
-		};
-	};
-
-	spl {
-		filename = "spl.bin";
-
-		mkimage {
-			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x912000";
-
-			blob {
-				filename = "u-boot-spl-ddr.bin";
-			};
-		};
-	};
-
-	itb {
-		filename = "u-boot.itb";
-
-		fit {
-			description = "Configuration to load ATF before U-Boot";
-			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-			fit,fdt-list = "of-list";
-			#address-cells = <1>;
-
-			images {
-				uboot {
-					arch = "arm64";
-					compression = "none";
-					description = "U-Boot (64-bit)";
-					load = <CONFIG_SYS_TEXT_BASE>;
-					type = "standalone";
-
-					uboot_blob {
-						filename = "u-boot-nodtb.bin";
-						type = "blob-ext";
-					};
-				};
-
-				atf {
-					arch = "arm64";
-					compression = "none";
-					description = "ARM Trusted Firmware";
-					entry = <0x960000>;
-					load = <0x960000>;
-					type = "firmware";
-
-					atf_blob {
-						filename = "bl31.bin";
-						type = "blob-ext";
-					};
-				};
-
-				binman_fip: fip {
-					arch = "arm64";
-					compression = "none";
-					description = "Trusted Firmware FIP";
-					load = <0x40310000>;
-					type = "firmware";
-				};
-
-				@fdt-SEQ {
-					compression = "none";
-					description = "NAME";
-					type = "flat_dt";
-
-					uboot_fdt_blob {
-						filename = "u-boot.dtb";
-						type = "blob-ext";
-					};
-				};
-			};
-
-			configurations {
-				default = "@config-DEFAULT-SEQ";
-
-				binman_configuration: @config-SEQ {
-					description = "NAME";
-					fdt = "fdt-SEQ";
-					firmware = "uboot";
-					loadables = "atf";
-				};
-			};
-		};
-	};
-
-	imx-boot {
-		filename = "flash.bin";
-		pad-byte = <0x00>;
-
-		spl {
-			filename = "spl.bin";
-			offset = <0x0>;

arch/arm/dts/imx8mn-venice-u-boot.dtsi line 260

Quoted 10 lines
arch/arm/dts/imx8mn-venice-u-boot.dtsi +0 -10
-			type = "blob-ext";
-		};
-
-		binman_uboot: uboot {
-			filename = "u-boot.itb";
-			offset = <0x58000>;
-			type = "blob-ext";
-		};
-	};
-};

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================