Skip to contentSkip to conversation

mips: ralink: mt7621: fix too-early kzalloc

RFC PATCH In review John Thomson 3 participants 9 messages Nov 3, 2022 – Nov 5, 2022

Subsystems (9)
Staging PCI MIPS Arm MediaTek +5 more subsystems
lore
Share & tools
lore
#0 lore raw

cover mips: ralink: mt7621: fix too-early kzalloc

ralink mt7621 attempts to use kzalloc before normal memory management is available.
Before v6.1-rc1, mt7621.c soc_dev_init silently failed to kzalloc and returned in soc_dev_init, but continued to boot without the soc device registered.
After, kernel crashes before it outputs any console messages

This was bisected to an mm/slub change (detailed in patch 3)

RFC due to
- probably a (much) better way to do this
- do not have mt7621 device with PCIe to test
drivers/phy/ralink/phy-mt7621-pci.c
- should this reference a commit as Fixes?

#1 lore raw

RFC PATCH 1/3 mips: ralink: mt7621: define MT7621_SYSC_BASE with __iomem

So that MT7621_SYSC_BASE can be used later in multiple functions without needing to repeat this __iomem declaration each time

---
 arch/mips/include/asm/mach-ralink/mt7621.h | 4 +++-
 arch/mips/ralink/mt7621.c                  | 7 +++----
 2 files changed, 6 insertions(+), 5 deletions(-)
arch/mips/include/asm/mach-ralink/mt7621.h +3 -1
index 6bbf082dd149..905c5b3ed2bd 100644
@@ -7,10 +7,12 @@
 #ifndef _MT7621_REGS_H_
 #define _MT7621_REGS_H_
 
+#define IOMEM(x)			((void __iomem *)(KSEG1ADDR(CPHYSADDR(x))))
+
 #define MT7621_PALMBUS_BASE		0x1C000000
 #define MT7621_PALMBUS_SIZE		0x03FFFFFF
 
-#define MT7621_SYSC_BASE		0x1E000000
+#define MT7621_SYSC_BASE		IOMEM(0x1E000000)
 
 #define SYSC_REG_CHIP_NAME0		0x00
 #define SYSC_REG_CHIP_NAME1		0x04
arch/mips/ralink/mt7621.c +3 -4
index fb0565bc34fd..17dbf28897e0 100644
@@ -126,7 +126,6 @@ static void soc_dev_init(struct ralink_soc_info *soc_info, u32 rev)
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
-	void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7621_SYSC_BASE);
 	unsigned char *name = NULL;
 	u32 n0;
 	u32 n1;
@@ -154,8 +153,8 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 		__sync();
 	}
 
-	n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
-	n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+	n0 = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME0);
+	n1 = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME1);
 
 	if (n0 == MT7621_CHIP_NAME0 && n1 == MT7621_CHIP_NAME1) {
 		name = "MT7621";
@@ -164,7 +163,7 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
 	}
 	ralink_soc = MT762X_SOC_MT7621AT;
-	rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
+	rev = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_REV);
 
 	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
 		"MediaTek %s ver:%u eco:%u",
Signature · 1 line
2.37.2
#2 lore raw

RFC PATCH 2/3 mips: ralink: mt7621: soc queries and tests as functions

In reply to John Thomson

Move the SoC register value queries and tests to specific functions, to remove repetition of logic
No functional changes intended

---
 arch/mips/ralink/mt7621.c | 86 +++++++++++++++++++++++++++------------
 1 file changed, 61 insertions(+), 25 deletions(-)
arch/mips/ralink/mt7621.c +61 -25
index 17dbf28897e0..f2443b833bc3 100644
@@ -97,7 +97,57 @@ void __init ralink_of_remap(void)
 		panic("Failed to remap core resources");
 }
 
-static void soc_dev_init(struct ralink_soc_info *soc_info, u32 rev)
+static const unsigned int __init mt7621_get_soc_name0(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME0);
+}
+
+static const unsigned int __init mt7621_get_soc_name1(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME1);
+}
+
+static const bool __init mt7621_soc_valid(void)
+{
+	if (mt7621_get_soc_name0() == MT7621_CHIP_NAME0 &&
+			mt7621_get_soc_name1() == MT7621_CHIP_NAME1)
+		return true;
+	else
+		return false;
+}
+
+static const char __init *mt7621_get_soc_id(void)
+{
+	if (mt7621_soc_valid())
+		return "MT7621";
+	else
+		return "invalid";
+}
+
+static const unsigned int __init mt7621_get_soc_rev(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_REV);
+}
+
+static const unsigned int __init mt7621_get_soc_ver(void)
+{
+	return (mt7621_get_soc_rev() >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK;
+}
+
+static const unsigned int __init mt7621_get_soc_eco(void)
+{
+	return (mt7621_get_soc_rev() & CHIP_REV_ECO_MASK);
+}
+
+static const char __init *mt7621_get_soc_revision(void)
+{
+	if (mt7621_get_soc_rev() == 1 && mt7621_get_soc_eco() == 1)
+		return "E2";
+	else
+		return "E1";
+}
+
+static void soc_dev_init(struct ralink_soc_info *soc_info)
 {
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
@@ -108,12 +158,7 @@ static void soc_dev_init(struct ralink_soc_info *soc_info, u32 rev)
 
 	soc_dev_attr->soc_id = "mt7621";
 	soc_dev_attr->family = "Ralink";
-
-	if (((rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK) == 1 &&
-	    (rev & CHIP_REV_ECO_MASK) == 1)
-		soc_dev_attr->revision = "E2";
-	else
-		soc_dev_attr->revision = "E1";
+	soc_dev_attr->revision = mt7621_get_soc_revision();
 
 	soc_dev_attr->data = soc_info;
 
@@ -126,11 +171,6 @@ static void soc_dev_init(struct ralink_soc_info *soc_info, u32 rev)
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
-	unsigned char *name = NULL;
-	u32 n0;
-	u32 n1;
-	u32 rev;
-
 	/* Early detection of CMP support */
 	mips_cm_probe();
 	mips_cpc_probe();
@@ -153,27 +193,23 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 		__sync();
 	}
 
-	n0 = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME0);
-	n1 = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME1);
-
-	if (n0 == MT7621_CHIP_NAME0 && n1 == MT7621_CHIP_NAME1) {
-		name = "MT7621";
+	if (mt7621_soc_valid())
 		soc_info->compatible = "mediatek,mt7621-soc";
-	} else {
-		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
-	}
+	else
+		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n",
+				mt7621_get_soc_name0(),
+				mt7621_get_soc_name1());
 	ralink_soc = MT762X_SOC_MT7621AT;
-	rev = __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_REV);
 
 	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
 		"MediaTek %s ver:%u eco:%u",
-		name,
-		(rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK,
-		(rev & CHIP_REV_ECO_MASK));
+		mt7621_get_soc_id(),
+		mt7621_get_soc_ver(),
+		mt7621_get_soc_eco());
 
 	soc_info->mem_detect = mt7621_memory_detect;
 
-	soc_dev_init(soc_info, rev);
+	soc_dev_init(soc_info);
 
 	if (!register_cps_smp_ops())
 		return;
Signature · 1 line
2.37.2
#3 lore raw

RFC PATCH 3/3 mips: ralink: mt7621: do not use kzalloc too early

In reply to John Thomson

Following commit 6edf2576a6cc ("mm/slub: enable debugging memory wasting of kmalloc") mt7621 failed to boot very early, without showing any console messages.
This exposed the pre-existing bug of mt7621.c using kzalloc before normal memory management was available.
Prior to this slub change, there existed the unintended protection against "kmem_cache *s" being NULL as slab_pre_alloc_hook() happened to return NULL and bailed out of slab_alloc_node().
This allowed mt7621 prom_soc_init to fail in the soc_dev_init kzalloc, but continue booting without this soc device.

Console output from a DEBUG_ZBOOT vmlinuz kernel loading, with mm/slub modified to warn on kmem_cache zero or null:

zimage at: 80B842A0 810B4BC0
Uncompressing Linux at load address 80001000
Copy device tree to address 80B80EE0
Now, booting the kernel...

[    0.000000] Linux version 6.1.0-rc3+ (john@john)
(mipsel-buildroot-linux-gnu-gcc.br_real (Buildroot
2021.11-4428-g6b6741b) 12.2.0, GNU ld (GNU Binutils) 2.39) #73 SMP Wed
     Nov  2 05:10:01 AEST 2022
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: CPU: 0 PID: 0 at mm/slub.c:3416
kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.1.0-rc3+ #73
[    0.000000] Stack : 810fff78 80084d98 00000000 00000004 00000000
00000000 80889d04 80c90000
[    0.000000]         80920000 807bd328 8089d368 80923bd3 00000000
00000001 80889cb0 00000000
[    0.000000]         00000000 00000000 807bd328 8084bcb1 00000002
00000002 00000001 6d6f4320
[    0.000000]         00000000 80c97d3d 80c97d68 fffffffc 807bd328
00000000 00000000 00000000
[    0.000000]         00000000 a0000000 80910000 8110a0b4 00000000
00000020 80010000 80010000
[    0.000000]         ...
[    0.000000] Call Trace:
[    0.000000] [<80008260>] show_stack+0x28/0xf0
[    0.000000] [<8070c958>] dump_stack_lvl+0x60/0x80
[    0.000000] [<8002e184>] __warn+0xc4/0xf8
[    0.000000] [<8002e210>] warn_slowpath_fmt+0x58/0xa4
[    0.000000] [<801c0fac>] kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] [<8092856c>] prom_soc_init+0x1fc/0x2b4
[    0.000000] [<80928060>] prom_init+0x44/0xf0
[    0.000000] [<80929214>] setup_arch+0x4c/0x6a8
[    0.000000] [<809257e0>] start_kernel+0x88/0x7c0
[    0.000000]
[    0.000000] ---[ end trace 0000000000000000 ]---
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled

This early kzalloc was introduced in commit 71b9b5e0130d ("MIPS: ralink:
mt7621: introduce 'soc_device' initialization")

---
 arch/mips/ralink/mt7621.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
arch/mips/ralink/mt7621.c +9 -5
index f2443b833bc3..836965021d5c 100644
@@ -25,6 +25,7 @@
 #define MT7621_MEM_TEST_PATTERN         0xaa5555aa
 
 static u32 detect_magic __initdata;
+struct ralink_soc_info *soc_info_ptr;
 
 int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
 {
@@ -147,27 +148,30 @@ static const char __init *mt7621_get_soc_revision(void)
 		return "E1";
 }
 
-static void soc_dev_init(struct ralink_soc_info *soc_info)
+static int __init mt7621_soc_dev_init(void)
 {
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
-		return;
+		return -ENOMEM;
 
 	soc_dev_attr->soc_id = "mt7621";
 	soc_dev_attr->family = "Ralink";
 	soc_dev_attr->revision = mt7621_get_soc_revision();
 
-	soc_dev_attr->data = soc_info;
+	soc_dev_attr->data = soc_info_ptr;
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev)) {
 		kfree(soc_dev_attr);
-		return;
+		return PTR_ERR(soc_dev);
 	}
+
+	return 0;
 }
+device_initcall(mt7621_soc_dev_init);
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
@@ -209,7 +213,7 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 
 	soc_info->mem_detect = mt7621_memory_detect;
 
-	soc_dev_init(soc_info);
+	soc_info_ptr = soc_info;
 
 	if (!register_cps_smp_ops())
 		return;
Signature · 1 line
2.37.2
#4 lore raw

Re: [RFC PATCH 3/3] mips: ralink: mt7621: do not use kzalloc too early

Quoted 122 lines · John Thomson

Following commit 6edf2576a6cc ("mm/slub: enable debugging memory wasting of kmalloc") mt7621 failed to boot very early, without showing any console messages.
This exposed the pre-existing bug of mt7621.c using kzalloc before normal memory management was available.
Prior to this slub change, there existed the unintended protection against "kmem_cache *s" being NULL as slab_pre_alloc_hook() happened to return NULL and bailed out of slab_alloc_node().
This allowed mt7621 prom_soc_init to fail in the soc_dev_init kzalloc, but continue booting without this soc device.

Console output from a DEBUG_ZBOOT vmlinuz kernel loading, with mm/slub modified to warn on kmem_cache zero or null:

zimage at: 80B842A0 810B4BC0
Uncompressing Linux at load address 80001000
Copy device tree to address 80B80EE0
Now, booting the kernel...

[    0.000000] Linux version 6.1.0-rc3+ (john@john)
(mipsel-buildroot-linux-gnu-gcc.br_real (Buildroot
2021.11-4428-g6b6741b) 12.2.0, GNU ld (GNU Binutils) 2.39) #73 SMP Wed
     Nov  2 05:10:01 AEST 2022
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: CPU: 0 PID: 0 at mm/slub.c:3416
kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.1.0-rc3+ #73
[    0.000000] Stack : 810fff78 80084d98 00000000 00000004 00000000
00000000 80889d04 80c90000
[    0.000000]         80920000 807bd328 8089d368 80923bd3 00000000
00000001 80889cb0 00000000
[    0.000000]         00000000 00000000 807bd328 8084bcb1 00000002
00000002 00000001 6d6f4320
[    0.000000]         00000000 80c97d3d 80c97d68 fffffffc 807bd328
00000000 00000000 00000000
[    0.000000]         00000000 a0000000 80910000 8110a0b4 00000000
00000020 80010000 80010000
[    0.000000]         ...
[    0.000000] Call Trace:
[    0.000000] [<80008260>] show_stack+0x28/0xf0
[    0.000000] [<8070c958>] dump_stack_lvl+0x60/0x80
[    0.000000] [<8002e184>] __warn+0xc4/0xf8
[    0.000000] [<8002e210>] warn_slowpath_fmt+0x58/0xa4
[    0.000000] [<801c0fac>] kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] [<8092856c>] prom_soc_init+0x1fc/0x2b4
[    0.000000] [<80928060>] prom_init+0x44/0xf0
[    0.000000] [<80929214>] setup_arch+0x4c/0x6a8
[    0.000000] [<809257e0>] start_kernel+0x88/0x7c0
[    0.000000]
[    0.000000] ---[ end trace 0000000000000000 ]---
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled

This early kzalloc was introduced in commit 71b9b5e0130d ("MIPS: ralink:
mt7621: introduce 'soc_device' initialization")

Link:
https://lore.kernel.org/linux-mm/[email protected]/

---
 arch/mips/ralink/mt7621.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
arch/mips/ralink/mt7621.c +9 -5
index f2443b833bc3..836965021d5c 100644
@@ -25,6 +25,7 @@
 #define MT7621_MEM_TEST_PATTERN         0xaa5555aa
 
 static u32 detect_magic __initdata;
+struct ralink_soc_info *soc_info_ptr;
 
 int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
 {
@@ -147,27 +148,30 @@ static const char __init *mt7621_get_soc_revision(void)
 		return "E1";
 }
 
-static void soc_dev_init(struct ralink_soc_info *soc_info)
+static int __init mt7621_soc_dev_init(void)
 {
 	struct soc_device *soc_dev;
 	struct soc_device_attribute *soc_dev_attr;
 
 	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
 	if (!soc_dev_attr)
-		return;
+		return -ENOMEM;
 
 	soc_dev_attr->soc_id = "mt7621";
 	soc_dev_attr->family = "Ralink";
 	soc_dev_attr->revision = mt7621_get_soc_revision();
 
-	soc_dev_attr->data = soc_info;
+	soc_dev_attr->data = soc_info_ptr;
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev)) {
 		kfree(soc_dev_attr);
-		return;
+		return PTR_ERR(soc_dev);
 	}
+
+	return 0;
 }
+device_initcall(mt7621_soc_dev_init);
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
@@ -209,7 +213,7 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 
 	soc_info->mem_detect = mt7621_memory_detect;
 
-	soc_dev_init(soc_info);
+	soc_info_ptr = soc_info;
 
 	if (!register_cps_smp_ops())
 		return;
Signature · 1 line
2.37.2

I backported this to kernel 5.10 as a test
without it, there was no /sys/bus/soc
with it, the drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c driver panicked in soc_device_match_attr
This was fixed with an added sentinel element in the quirk table:

drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c +0 -0
@@ -293,7 +293,8 @@ static struct phy *mt7621_pcie_phy_of_xlate(struct device *d

ev,
}

static const struct soc_device_attribute mt7621_pci_quirks_match[] = {

-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }

};

static const struct regmap_config mt7621_pci_phy_regmap_config = {

There is the same quirk table to kernel 5.15 in drivers/staging/mt7621-pci/pci-mt7621.c Should I add commits for these for the stable kernels?

In master, these files are now
drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c

Should I add sentinels to the soc_device_attribute quirk tables in all of these files?

Cheers,

Signature · 1 line
  John Thomson
#5 lore raw

Re: [RFC PATCH 3/3] mips: ralink: mt7621: do not use kzalloc too early

Hi John,

Thanks for the patches!

Quoted 47 lines · John Thomson
Quoted 45 lines · John Thomson

Following commit 6edf2576a6cc ("mm/slub: enable debugging memory wasting of kmalloc") mt7621 failed to boot very early, without showing any console messages.
This exposed the pre-existing bug of mt7621.c using kzalloc before normal memory management was available.
Prior to this slub change, there existed the unintended protection against "kmem_cache *s" being NULL as slab_pre_alloc_hook() happened to return NULL and bailed out of slab_alloc_node().
This allowed mt7621 prom_soc_init to fail in the soc_dev_init kzalloc, but continue booting without this soc device.

Console output from a DEBUG_ZBOOT vmlinuz kernel loading, with mm/slub modified to warn on kmem_cache zero or null:

zimage at: 80B842A0 810B4BC0
Uncompressing Linux at load address 80001000
Copy device tree to address 80B80EE0
Now, booting the kernel...

[    0.000000] Linux version 6.1.0-rc3+ (john@john)
(mipsel-buildroot-linux-gnu-gcc.br_real (Buildroot
2021.11-4428-g6b6741b) 12.2.0, GNU ld (GNU Binutils) 2.39) #73 SMP Wed
     Nov  2 05:10:01 AEST 2022
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: CPU: 0 PID: 0 at mm/slub.c:3416
kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.1.0-rc3+ #73
[    0.000000] Stack : 810fff78 80084d98 00000000 00000004 00000000
00000000 80889d04 80c90000
[    0.000000]         80920000 807bd328 8089d368 80923bd3 00000000
00000001 80889cb0 00000000
[    0.000000]         00000000 00000000 807bd328 8084bcb1 00000002
00000002 00000001 6d6f4320
[    0.000000]         00000000 80c97d3d 80c97d68 fffffffc 807bd328
00000000 00000000 00000000
[    0.000000]         00000000 a0000000 80910000 8110a0b4 00000000
00000020 80010000 80010000
[    0.000000]         ...
[    0.000000] Call Trace:
[    0.000000] [<80008260>] show_stack+0x28/0xf0
[    0.000000] [<8070c958>] dump_stack_lvl+0x60/0x80
[    0.000000] [<8002e184>] __warn+0xc4/0xf8
[    0.000000] [<8002e210>] warn_slowpath_fmt+0x58/0xa4
[    0.000000] [<801c0fac>] kmem_cache_alloc+0x5a4/0x5e8
Quoted 8 lines
Quoted 8 lines
[    0.000000] [<8092856c>] prom_soc_init+0x1fc/0x2b4
[    0.000000] [<80928060>] prom_init+0x44/0xf0
[    0.000000] [<80929214>] setup_arch+0x4c/0x6a8
[    0.000000] [<809257e0>] start_kernel+0x88/0x7c0
[    0.000000]
[    0.000000] ---[ end trace 0000000000000000 ]---
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled

Last version I tested on my gnubee PC1 mt7621 board was v6.0 and all was booting properly.

Quoted 62 lines
Quoted 62 lines

This early kzalloc was introduced in commit 71b9b5e0130d ("MIPS: ralink:
mt7621: introduce 'soc_device' initialization")

Link:
https://lore.kernel.org/linux-mm/[email protected]/

---
 arch/mips/ralink/mt7621.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
arch/mips/ralink/mt7621.c +8 -4
index f2443b833bc3..836965021d5c 100644
@@ -25,6 +25,7 @@
 #define MT7621_MEM_TEST_PATTERN         0xaa5555aa
 
 static u32 detect_magic __initdata;
+struct ralink_soc_info *soc_info_ptr;
 
 int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
 {
@@ -147,27 +148,30 @@ static const char __init *mt7621_get_soc_revision(void)
              return "E1";
 }
 
-static void soc_dev_init(struct ralink_soc_info *soc_info)
+static int __init mt7621_soc_dev_init(void)
 {
      struct soc_device *soc_dev;
      struct soc_device_attribute *soc_dev_attr;
 
      soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
      if (!soc_dev_attr)
-             return;
+             return -ENOMEM;
 
      soc_dev_attr->soc_id = "mt7621";
      soc_dev_attr->family = "Ralink";
      soc_dev_attr->revision = mt7621_get_soc_revision();
 
-     soc_dev_attr->data = soc_info;
+     soc_dev_attr->data = soc_info_ptr;
 
      soc_dev = soc_device_register(soc_dev_attr);
      if (IS_ERR(soc_dev)) {
              kfree(soc_dev_attr);
-             return;
+             return PTR_ERR(soc_dev);
      }
+
+     return 0;
 }
+device_initcall(mt7621_soc_dev_init);
 
 void __init prom_soc_init(struct ralink_soc_info *soc_info)
 {
@@ -209,7 +213,7 @@ void __init prom_soc_init(struct ralink_soc_info *soc_info)
 
      soc_info->mem_detect = mt7621_memory_detect;
 
Quoted 7 lines
Quoted 7 lines
arch/mips/ralink/mt7621.c +1 -2
-     soc_dev_init(soc_info);
+     soc_info_ptr = soc_info;
 
      if (!register_cps_smp_ops())
              return;
--

2.37.2

I was trying to quicky add all of them to my trew using b4 with [0] but I am getting a DNS error with that URL...

So, I am a bit busy this week but hopefully next week I'll try to make time to test all of your changes. Let me test all your changes and come back to you again.

[0]: https://lore.kernel.org/lkml/[email protected]/T/#m75e858f83a3e2e26ca84295d2d09040e14128e71

Quoted 20 lines

I backported this to kernel 5.10 as a test
without it, there was no /sys/bus/soc
with it, the drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c driver panicked in soc_device_match_attr
This was fixed with an added sentinel element in the quirk table:

drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c +2 -1
@@ -293,7 +293,8 @@ static struct phy *mt7621_pcie_phy_of_xlate(struct device *d
 ev,
 }
 
 static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }
 };
 

static const struct regmap_config mt7621_pci_phy_regmap_config = {

Quoted 8 lines

There is the same quirk table to kernel 5.15 in drivers/staging/mt7621-pci/pci-mt7621.c Should I add commits for these for the stable kernels?

In master, these files are now
drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c

Should I add sentinels to the soc_device_attribute quirk tables in all of these files?

I guess we should add sentinel in all related files. Please CC me with your series if you send any patch before I come back to you after testing.

Quoted 4 lines

Cheers,
--
John Thomson

Thanks,
Sergio Paracuellos

maintainer Tested-by Acked-by
#6 lore raw

Re: [RFC PATCH 3/3] mips: ralink: mt7621: do not use kzalloc too early

Hi John,

Quoted 63 lines · Sergio Paracuellos

Hi John,

Thanks for the patches!

Quoted 47 lines · John Thomson
Quoted 45 lines · John Thomson

Following commit 6edf2576a6cc ("mm/slub: enable debugging memory wasting of kmalloc") mt7621 failed to boot very early, without showing any console messages.
This exposed the pre-existing bug of mt7621.c using kzalloc before normal memory management was available.
Prior to this slub change, there existed the unintended protection against "kmem_cache *s" being NULL as slab_pre_alloc_hook() happened to return NULL and bailed out of slab_alloc_node().
This allowed mt7621 prom_soc_init to fail in the soc_dev_init kzalloc, but continue booting without this soc device.

Console output from a DEBUG_ZBOOT vmlinuz kernel loading, with mm/slub modified to warn on kmem_cache zero or null:

zimage at: 80B842A0 810B4BC0
Uncompressing Linux at load address 80001000
Copy device tree to address 80B80EE0
Now, booting the kernel...

[    0.000000] Linux version 6.1.0-rc3+ (john@john)
(mipsel-buildroot-linux-gnu-gcc.br_real (Buildroot
2021.11-4428-g6b6741b) 12.2.0, GNU ld (GNU Binutils) 2.39) #73 SMP Wed
     Nov  2 05:10:01 AEST 2022
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: CPU: 0 PID: 0 at mm/slub.c:3416
kmem_cache_alloc+0x5a4/0x5e8
[    0.000000] Modules linked in:
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.1.0-rc3+ #73
[    0.000000] Stack : 810fff78 80084d98 00000000 00000004 00000000
00000000 80889d04 80c90000
[    0.000000]         80920000 807bd328 8089d368 80923bd3 00000000
00000001 80889cb0 00000000
[    0.000000]         00000000 00000000 807bd328 8084bcb1 00000002
00000002 00000001 6d6f4320
[    0.000000]         00000000 80c97d3d 80c97d68 fffffffc 807bd328
00000000 00000000 00000000
[    0.000000]         00000000 a0000000 80910000 8110a0b4 00000000
00000020 80010000 80010000
[    0.000000]         ...
[    0.000000] Call Trace:
[    0.000000] [<80008260>] show_stack+0x28/0xf0
[    0.000000] [<8070c958>] dump_stack_lvl+0x60/0x80
[    0.000000] [<8002e184>] __warn+0xc4/0xf8
[    0.000000] [<8002e210>] warn_slowpath_fmt+0x58/0xa4
[    0.000000] [<801c0fac>] kmem_cache_alloc+0x5a4/0x5e8
Quoted 8 lines
Quoted 8 lines
[    0.000000] [<8092856c>] prom_soc_init+0x1fc/0x2b4
[    0.000000] [<80928060>] prom_init+0x44/0xf0
[    0.000000] [<80929214>] setup_arch+0x4c/0x6a8
[    0.000000] [<809257e0>] start_kernel+0x88/0x7c0
[    0.000000]
[    0.000000] ---[ end trace 0000000000000000 ]---
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
Quoted 2 lines

Last version I tested on my gnubee PC1 mt7621 board was v6.0 and all was booting properly.

I have verified with 6.1.0-rc1 system does not boot as you was pointed out here. After adding your patches the system boots and got an Oops because soc_device_match_attr:

[   20.569959] CPU 0 Unable to handle kernel paging request at virtual
address 675f6b6c, epc == 80403dec, ra == 804ae11c
[   20.591060] Oops[#1]:
[   20.595462] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1+ #148
[   20.608265] $ 0   : 00000000 00000001 82262a00 00000000
[   20.618615] $ 4   : 675f6b6c 808dea04 00000000 804ae138
[   20.628983] $ 8   : 00000000 808787ba 00000000 821f4b00
[   20.639351] $12   : 0000005b 0000005d 0000002d 0000005c
[   20.649735] $16   : 82253580 807b4034 807b4034 804ae138
[   20.660087] $20   : fffffff4 82c382b8 809e1094 00000008
[   20.670455] $24   : 0000002a 0000003f
[   20.680823] $28   : 82050000 82051c30 80a0d638 804ae11c
[   20.691190] Hi    : 00000037
[   20.696891] Lo    : 5c28f6a0
[   20.702610] epc   : 80403dec glob_match+0x1c/0x240
[   20.712100] ra    : 804ae11c soc_device_match_attr+0xac/0xc8
[   20.723330] Status: 11000403 KERNEL EXL IE
[   20.731626] Cause : 40800008 (ExcCode 02)
[   20.739576] BadVA : 675f6b6c
[   20.745277] PrId  : 0001992f (MIPS 1004Kc)
[   20.753414] Modules linked in:
[   20.759448] Process swapper/0 (pid: 1, threadinfo=(ptrval),
task=(ptrval), tls=00000000)
[   20.775520] Stack : fffffff4 80496ab8 820c6010 828c8518 80950000
ffffffea 80950000 80496b48
[   20.792106]         00000000 828c8400 820c6010 821f4880 1e160000
821bc754 82253734 7f8268e6
[   20.808707]         809c6a94 807b4034 804ae138 809c8e88 819a0000
804ae1d8 80a0d638 80438e10
[   20.825282]         821f3e70 80950000 808c0000 828c8400 820c6000
828c8548 820c6010 80456608
[   20.841879]         821f3dc0 821d32c0 819a0000 801d8768 821f3dc0
821d32c0 828c8540 80950000
[   20.858473]         ...
[   20.863298] Call Trace:
[   20.868137] [<80403dec>] glob_match+0x1c/0x240
[   20.876955] [<804ae11c>] soc_device_match_attr+0xac/0xc8
[   20.887500] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.897176] [<804ae1d8>] soc_device_match+0x98/0xc8
[   20.906869] [<80456608>] mt7621_pcie_probe+0x90/0x7b8
[   20.916876] [<8049b46c>] platform_probe+0x54/0x94
[   20.926206] [<80499058>] really_probe+0x200/0x434
[   20.935538] [<80499520>] driver_probe_device+0x44/0xd4
[   20.945732] [<80499ae0>] __driver_attach+0xb8/0x1b0
[   20.955428] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.965089] [<80497f18>] bus_add_driver+0x100/0x218
[   20.974763] [<8049a338>] driver_register+0xd0/0x118
[   20.984438] [<80001590>] do_one_initcall+0x8c/0x28c
[   20.994115] [<809e21c8>] kernel_init_freeable+0x254/0x28c
[   21.004845] [<80781070>] kernel_init+0x24/0x118
[   21.013830] [<800034f8>] ret_from_kernel_thread+0x14/0x1c
[   21.024522]
[   21.027457] Code: 240f005c  2418002a  2419003f <80820000> 24a90001
90a70000  104c006f  24860001  2843005c
[   21.046810]
[   21.049830] ---[ end trace 0000000000000000 ]---
[   21.058935] Kernel panic - not syncing: Fatal exception
[   21.069310] Rebooting in 1 seconds..

I have fixed this adding two sentinels in the following files:

drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c

sergio@camaron:~/GNUBEE-SERGIO-TEST/linux$ git diff
drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c
(quoted diff) +0 -0

b/drivers/pci/controller/pcie-mt7621.c
index 4bd1abf26008..ee7aad09d627 100644

drivers/pci/controller/pcie-mt7621.c +0 -0
@@ -466,7 +466,8 @@ static int mt7621_pcie_register_host(struct

pci_host_bridge *host)
}

static const struct soc_device_attribute mt7621_pcie_quirks_match[] = {

-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }

};

static int mt7621_pcie_probe(struct platform_device *pdev)

(quoted diff) +0 -0

b/drivers/phy/ralink/phy-mt7621-pci.c
index 5e6530f545b5..85888ab2d307 100644

drivers/phy/ralink/phy-mt7621-pci.c +0 -0
@@ -280,7 +280,8 @@ static struct phy *mt7621_pcie_phy_of_xlate(struct

device *dev,
}

static const struct soc_device_attribute mt7621_pci_quirks_match[] = {

-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }

};

static const struct regmap_config mt7621_pci_phy_regmap_config = {

With this two minor changes and your patches the system properly boots and behaves properly.

So FWIW feel free to add my:

Please, let me know if you want me to send any patches or if you are going to create a complete patchset with all the needed changes.

Thank you very much for doing this!

Best regards,
Sergio Paracuellos

[snip]

#7 lore raw

Re: [RFC PATCH 3/3] mips: ralink: mt7621: do not use kzalloc too early

Quoted 104 lines · Sergio Paracuellos

I have verified with 6.1.0-rc1 system does not boot as you was pointed out here. After adding your patches the system boots and got an Oops because soc_device_match_attr:

[   20.569959] CPU 0 Unable to handle kernel paging request at virtual
address 675f6b6c, epc == 80403dec, ra == 804ae11c
[   20.591060] Oops[#1]:
[   20.595462] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1+ #148
[   20.608265] $ 0   : 00000000 00000001 82262a00 00000000
[   20.618615] $ 4   : 675f6b6c 808dea04 00000000 804ae138
[   20.628983] $ 8   : 00000000 808787ba 00000000 821f4b00
[   20.639351] $12   : 0000005b 0000005d 0000002d 0000005c
[   20.649735] $16   : 82253580 807b4034 807b4034 804ae138
[   20.660087] $20   : fffffff4 82c382b8 809e1094 00000008
[   20.670455] $24   : 0000002a 0000003f
[   20.680823] $28   : 82050000 82051c30 80a0d638 804ae11c
[   20.691190] Hi    : 00000037
[   20.696891] Lo    : 5c28f6a0
[   20.702610] epc   : 80403dec glob_match+0x1c/0x240
[   20.712100] ra    : 804ae11c soc_device_match_attr+0xac/0xc8
[   20.723330] Status: 11000403 KERNEL EXL IE
[   20.731626] Cause : 40800008 (ExcCode 02)
[   20.739576] BadVA : 675f6b6c
[   20.745277] PrId  : 0001992f (MIPS 1004Kc)
[   20.753414] Modules linked in:
[   20.759448] Process swapper/0 (pid: 1, threadinfo=(ptrval),
task=(ptrval), tls=00000000)
[   20.775520] Stack : fffffff4 80496ab8 820c6010 828c8518 80950000
ffffffea 80950000 80496b48
[   20.792106]         00000000 828c8400 820c6010 821f4880 1e160000
821bc754 82253734 7f8268e6
[   20.808707]         809c6a94 807b4034 804ae138 809c8e88 819a0000
804ae1d8 80a0d638 80438e10
[   20.825282]         821f3e70 80950000 808c0000 828c8400 820c6000
828c8548 820c6010 80456608
[   20.841879]         821f3dc0 821d32c0 819a0000 801d8768 821f3dc0
821d32c0 828c8540 80950000
[   20.858473]         ...
[   20.863298] Call Trace:
[   20.868137] [<80403dec>] glob_match+0x1c/0x240
[   20.876955] [<804ae11c>] soc_device_match_attr+0xac/0xc8
[   20.887500] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.897176] [<804ae1d8>] soc_device_match+0x98/0xc8
[   20.906869] [<80456608>] mt7621_pcie_probe+0x90/0x7b8
[   20.916876] [<8049b46c>] platform_probe+0x54/0x94
[   20.926206] [<80499058>] really_probe+0x200/0x434
[   20.935538] [<80499520>] driver_probe_device+0x44/0xd4
[   20.945732] [<80499ae0>] __driver_attach+0xb8/0x1b0
[   20.955428] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.965089] [<80497f18>] bus_add_driver+0x100/0x218
[   20.974763] [<8049a338>] driver_register+0xd0/0x118
[   20.984438] [<80001590>] do_one_initcall+0x8c/0x28c
[   20.994115] [<809e21c8>] kernel_init_freeable+0x254/0x28c
[   21.004845] [<80781070>] kernel_init+0x24/0x118
[   21.013830] [<800034f8>] ret_from_kernel_thread+0x14/0x1c
[   21.024522]
[   21.027457] Code: 240f005c  2418002a  2419003f <80820000> 24a90001
90a70000  104c006f  24860001  2843005c
[   21.046810]
[   21.049830] ---[ end trace 0000000000000000 ]---
[   21.058935] Kernel panic - not syncing: Fatal exception
[   21.069310] Rebooting in 1 seconds..

I have fixed this adding two sentinels in the following files:

drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c

sergio@camaron:~/GNUBEE-SERGIO-TEST/linux$ git diff
drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c
drivers/pci/controller/pcie-mt7621.c +2 -1
index 4bd1abf26008..ee7aad09d627 100644
@@ -466,7 +466,8 @@ static int mt7621_pcie_register_host(struct
 pci_host_bridge *host)
 }
 
 static const struct soc_device_attribute mt7621_pcie_quirks_match[] = {
-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }
 };
 

static int mt7621_pcie_probe(struct platform_device *pdev)

drivers/phy/ralink/phy-mt7621-pci.c +2 -1
index 5e6530f545b5..85888ab2d307 100644
@@ -280,7 +280,8 @@ static struct phy *mt7621_pcie_phy_of_xlate(struct
 device *dev,
 }
 
 static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }
 };
 

static const struct regmap_config mt7621_pci_phy_regmap_config = {

Quoted 2 lines

With this two minor changes and your patches the system properly boots and behaves properly.

Thank you for finding time, and testing and verifying this.

Quoted 8 lines

So FWIW feel free to add my:

Please, let me know if you want me to send any patches or if you are going to create a complete patchset with all the needed changes.

I sent in these two patches with Fixes tags, and some queries about getting
those pci & phy changes in before this fix, and also possibly in the 5.10 and 5.15 stable trees, in case we want this kzalloc change too early backported as well? Please let me know what you think.

Quoted 7 lines

Thank you very much for doing this!

Best regards,
Sergio Paracuellos

[snip]

Some more queries here:
I should add a note in this commit message that this boot failure only happens with CONFIG_SLUB=y Fixes reference or not?
Fixes 71b9b5e0130d ("MIPS: ralink: mt7621: introduce 'soc_device' initialization")
I used device_initcall, but postcore_initcall also works fine, and I am not sure of the difference here.

Cheers,

Signature · 1 line
  John Thomson
#8 lore raw

Re: [RFC PATCH 3/3] mips: ralink: mt7621: do not use kzalloc too early

Hi John,

Quoted 118 lines · John Thomson
Quoted 104 lines · Sergio Paracuellos

I have verified with 6.1.0-rc1 system does not boot as you was pointed out here. After adding your patches the system boots and got an Oops because soc_device_match_attr:

[   20.569959] CPU 0 Unable to handle kernel paging request at virtual
address 675f6b6c, epc == 80403dec, ra == 804ae11c
[   20.591060] Oops[#1]:
[   20.595462] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1+ #148
[   20.608265] $ 0   : 00000000 00000001 82262a00 00000000
[   20.618615] $ 4   : 675f6b6c 808dea04 00000000 804ae138
[   20.628983] $ 8   : 00000000 808787ba 00000000 821f4b00
[   20.639351] $12   : 0000005b 0000005d 0000002d 0000005c
[   20.649735] $16   : 82253580 807b4034 807b4034 804ae138
[   20.660087] $20   : fffffff4 82c382b8 809e1094 00000008
[   20.670455] $24   : 0000002a 0000003f
[   20.680823] $28   : 82050000 82051c30 80a0d638 804ae11c
[   20.691190] Hi    : 00000037
[   20.696891] Lo    : 5c28f6a0
[   20.702610] epc   : 80403dec glob_match+0x1c/0x240
[   20.712100] ra    : 804ae11c soc_device_match_attr+0xac/0xc8
[   20.723330] Status: 11000403 KERNEL EXL IE
[   20.731626] Cause : 40800008 (ExcCode 02)
[   20.739576] BadVA : 675f6b6c
[   20.745277] PrId  : 0001992f (MIPS 1004Kc)
[   20.753414] Modules linked in:
[   20.759448] Process swapper/0 (pid: 1, threadinfo=(ptrval),
task=(ptrval), tls=00000000)
[   20.775520] Stack : fffffff4 80496ab8 820c6010 828c8518 80950000
ffffffea 80950000 80496b48
[   20.792106]         00000000 828c8400 820c6010 821f4880 1e160000
821bc754 82253734 7f8268e6
[   20.808707]         809c6a94 807b4034 804ae138 809c8e88 819a0000
804ae1d8 80a0d638 80438e10
[   20.825282]         821f3e70 80950000 808c0000 828c8400 820c6000
828c8548 820c6010 80456608
[   20.841879]         821f3dc0 821d32c0 819a0000 801d8768 821f3dc0
821d32c0 828c8540 80950000
[   20.858473]         ...
[   20.863298] Call Trace:
[   20.868137] [<80403dec>] glob_match+0x1c/0x240
[   20.876955] [<804ae11c>] soc_device_match_attr+0xac/0xc8
[   20.887500] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.897176] [<804ae1d8>] soc_device_match+0x98/0xc8
[   20.906869] [<80456608>] mt7621_pcie_probe+0x90/0x7b8
[   20.916876] [<8049b46c>] platform_probe+0x54/0x94
[   20.926206] [<80499058>] really_probe+0x200/0x434
[   20.935538] [<80499520>] driver_probe_device+0x44/0xd4
[   20.945732] [<80499ae0>] __driver_attach+0xb8/0x1b0
[   20.955428] [<80496b48>] bus_for_each_dev+0x7c/0xc0
[   20.965089] [<80497f18>] bus_add_driver+0x100/0x218
[   20.974763] [<8049a338>] driver_register+0xd0/0x118
[   20.984438] [<80001590>] do_one_initcall+0x8c/0x28c
[   20.994115] [<809e21c8>] kernel_init_freeable+0x254/0x28c
[   21.004845] [<80781070>] kernel_init+0x24/0x118
[   21.013830] [<800034f8>] ret_from_kernel_thread+0x14/0x1c
[   21.024522]
[   21.027457] Code: 240f005c  2418002a  2419003f <80820000> 24a90001
90a70000  104c006f  24860001  2843005c
[   21.046810]
[   21.049830] ---[ end trace 0000000000000000 ]---
[   21.058935] Kernel panic - not syncing: Fatal exception
[   21.069310] Rebooting in 1 seconds..

I have fixed this adding two sentinels in the following files:

drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c

sergio@camaron:~/GNUBEE-SERGIO-TEST/linux$ git diff
drivers/pci/controller/pcie-mt7621.c
drivers/phy/ralink/phy-mt7621-pci.c
drivers/pci/controller/pcie-mt7621.c +2 -1
index 4bd1abf26008..ee7aad09d627 100644
@@ -466,7 +466,8 @@ static int mt7621_pcie_register_host(struct
 pci_host_bridge *host)
 }
 
 static const struct soc_device_attribute mt7621_pcie_quirks_match[] = {
-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }
 };
 

static int mt7621_pcie_probe(struct platform_device *pdev)

drivers/phy/ralink/phy-mt7621-pci.c +2 -1
index 5e6530f545b5..85888ab2d307 100644
@@ -280,7 +280,8 @@ static struct phy *mt7621_pcie_phy_of_xlate(struct
 device *dev,
 }
 
 static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
-       { .soc_id = "mt7621", .revision = "E2" }
+       { .soc_id = "mt7621", .revision = "E2" },
+       { /* sentinel */ }
 };
 

static const struct regmap_config mt7621_pci_phy_regmap_config = {

Quoted 2 lines

With this two minor changes and your patches the system properly boots and behaves properly.

Thank you for finding time, and testing and verifying this.

Quoted 6 lines

So FWIW feel free to add my:

Quoted 6 lines
Quoted 2 lines

Please, let me know if you want me to send any patches or if you are going to create a complete patchset with all the needed changes.

I sent in these two patches with Fixes tags, and some queries about getting
those pci & phy changes in before this fix, and also possibly in the 5.10 and 5.15 stable trees, in case we want this kzalloc change too early backported as well? Please let me know what you think.

I don't really know. I don't think kzalloc patches are stable material, so I don't think we have a real need of backporting these two also. Also, this SoC is used intensively for the openWRT community and never reported an issue in this way and they are using both 5.10 (stable) and 5.15 (development) kernels.

Quoted 11 lines
Quoted 8 lines

Thank you very much for doing this!

Best regards,
Sergio Paracuellos

[snip]

Some more queries here:
I should add a note in this commit message that this boot failure only happens with CONFIG_SLUB=y

It does not hurt at all adding this, so it will be helpful for sure in future if issues appear.

Quoted 2 lines

Fixes reference or not?
Fixes 71b9b5e0130d ("MIPS: ralink: mt7621: introduce 'soc_device' initialization")

I guess it should be also there.

Quoted 1 line

I used device_initcall, but postcore_initcall also works fine, and I am not sure of the difference here.

Difference is the execution order at boot. postcore_initcall is executed earlier than device_initcall. See [0] for details.

Thanks.
Sergio Paracuellos

[0]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/init/main.c

Quoted 5 lines

Cheers,
--
John Thomson