Skip to contentSkip to conversation

net: hinic: Convert the cmd code from decimal to hex to be more readable

PATCH Applied Cai Huoqing 2 participants 4 messages Nov 3, 2022 – Nov 7, 2022

Subsystems (3)
lore
Share & tools
lore

Cai Huoqing

author maintainer
#0 lore raw

PATCH v4 1/3 net: hinic: Convert the cmd code from decimal to hex to be more readable

The print cmd code is in hex, so using hex cmd code intead of decimal is easy to check the value with print info.

---
v1->v2:

	1.Add net-next prefix.
	The comments link: https://lore.kernel.org/lkml/[email protected]/
v2->v3:
	1.Merge PATCH 3/3 to this series.
v3->v4:
	1.Revert the empty lines.
	The comments link: https://lore.kernel.org/lkml/[email protected]/
 .../net/ethernet/huawei/hinic/hinic_hw_dev.h  | 104 +++++++++---------
 1 file changed, 52 insertions(+), 52 deletions(-)
drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h +52 -52
index d2d89b0a5ef0..6dae116a11f8 100644
@@ -46,104 +46,104 @@ enum hinic_port_cmd {
 	HINIC_PORT_CMD_VF_REGISTER = 0x0,
 	HINIC_PORT_CMD_VF_UNREGISTER = 0x1,
 
-	HINIC_PORT_CMD_CHANGE_MTU       = 2,
+	HINIC_PORT_CMD_CHANGE_MTU = 0x2,
 
-	HINIC_PORT_CMD_ADD_VLAN         = 3,
-	HINIC_PORT_CMD_DEL_VLAN         = 4,
+	HINIC_PORT_CMD_ADD_VLAN = 0x3,
+	HINIC_PORT_CMD_DEL_VLAN = 0x4,
 
-	HINIC_PORT_CMD_SET_PFC		= 5,
+	HINIC_PORT_CMD_SET_PFC = 0x5,
 
-	HINIC_PORT_CMD_SET_MAC          = 9,
-	HINIC_PORT_CMD_GET_MAC          = 10,
-	HINIC_PORT_CMD_DEL_MAC          = 11,
+	HINIC_PORT_CMD_SET_MAC = 0x9,
+	HINIC_PORT_CMD_GET_MAC = 0xA,
+	HINIC_PORT_CMD_DEL_MAC = 0xB,
 
-	HINIC_PORT_CMD_SET_RX_MODE      = 12,
+	HINIC_PORT_CMD_SET_RX_MODE = 0xC,
 
-	HINIC_PORT_CMD_GET_PAUSE_INFO	= 20,
-	HINIC_PORT_CMD_SET_PAUSE_INFO	= 21,
+	HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14,
+	HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15,
 
-	HINIC_PORT_CMD_GET_LINK_STATE   = 24,
+	HINIC_PORT_CMD_GET_LINK_STATE = 0x18,
 
-	HINIC_PORT_CMD_SET_LRO		= 25,
+	HINIC_PORT_CMD_SET_LRO = 0x19,
 
-	HINIC_PORT_CMD_SET_RX_CSUM	= 26,
+	HINIC_PORT_CMD_SET_RX_CSUM = 0x1A,
 
-	HINIC_PORT_CMD_SET_RX_VLAN_OFFLOAD = 27,
+	HINIC_PORT_CMD_SET_RX_VLAN_OFFLOAD = 0x1B,
 
-	HINIC_PORT_CMD_GET_PORT_STATISTICS = 28,
+	HINIC_PORT_CMD_GET_PORT_STATISTICS = 0x1C,
 
-	HINIC_PORT_CMD_CLEAR_PORT_STATISTICS = 29,
+	HINIC_PORT_CMD_CLEAR_PORT_STATISTICS = 0x1D,
 
-	HINIC_PORT_CMD_GET_VPORT_STAT	= 30,
+	HINIC_PORT_CMD_GET_VPORT_STAT = 0x1E,
 
-	HINIC_PORT_CMD_CLEAN_VPORT_STAT	= 31,
+	HINIC_PORT_CMD_CLEAN_VPORT_STAT	= 0x1F,
 
-	HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 37,
+	HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25,
 
-	HINIC_PORT_CMD_SET_PORT_STATE   = 41,
+	HINIC_PORT_CMD_SET_PORT_STATE = 0x29,
 
-	HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 43,
+	HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B,
 
-	HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 44,
+	HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 0x2C,
 
-	HINIC_PORT_CMD_SET_RSS_HASH_ENGINE = 45,
+	HINIC_PORT_CMD_SET_RSS_HASH_ENGINE = 0x2D,
 
-	HINIC_PORT_CMD_GET_RSS_HASH_ENGINE = 46,
+	HINIC_PORT_CMD_GET_RSS_HASH_ENGINE = 0x2E,
 
-	HINIC_PORT_CMD_GET_RSS_CTX_TBL  = 47,
+	HINIC_PORT_CMD_GET_RSS_CTX_TBL = 0x2F,
 
-	HINIC_PORT_CMD_SET_RSS_CTX_TBL  = 48,
+	HINIC_PORT_CMD_SET_RSS_CTX_TBL = 0x30,
 
-	HINIC_PORT_CMD_RSS_TEMP_MGR	= 49,
+	HINIC_PORT_CMD_RSS_TEMP_MGR	= 0x31,
 
-	HINIC_PORT_CMD_RD_LINE_TBL	= 57,
+	HINIC_PORT_CMD_RD_LINE_TBL = 0x39,
 
-	HINIC_PORT_CMD_RSS_CFG		= 66,
+	HINIC_PORT_CMD_RSS_CFG = 0x42,
 
-	HINIC_PORT_CMD_FWCTXT_INIT      = 69,
+	HINIC_PORT_CMD_FWCTXT_INIT = 0x45,
 
-	HINIC_PORT_CMD_GET_LOOPBACK_MODE = 72,
-	HINIC_PORT_CMD_SET_LOOPBACK_MODE,
+	HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48,
+	HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49,
 
-	HINIC_PORT_CMD_ENABLE_SPOOFCHK = 78,
+	HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E,
 
-	HINIC_PORT_CMD_GET_MGMT_VERSION = 88,
+	HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58,
 
-	HINIC_PORT_CMD_SET_FUNC_STATE   = 93,
+	HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D,
 
-	HINIC_PORT_CMD_GET_GLOBAL_QPN   = 102,
+	HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66,
 
-	HINIC_PORT_CMD_SET_VF_RATE = 105,
+	HINIC_PORT_CMD_SET_VF_RATE = 0x69,
 
-	HINIC_PORT_CMD_SET_VF_VLAN	= 106,
+	HINIC_PORT_CMD_SET_VF_VLAN = 0x6A,
 
-	HINIC_PORT_CMD_CLR_VF_VLAN,
+	HINIC_PORT_CMD_CLR_VF_VLAN = 0x6B,
 
-	HINIC_PORT_CMD_SET_TSO          = 112,
+	HINIC_PORT_CMD_SET_TSO = 0x70,
 
-	HINIC_PORT_CMD_UPDATE_FW	= 114,
+	HINIC_PORT_CMD_UPDATE_FW = 0x72,
 
-	HINIC_PORT_CMD_SET_RQ_IQ_MAP	= 115,
+	HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73,
 
-	HINIC_PORT_CMD_LINK_STATUS_REPORT = 160,
+	HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0,
 
-	HINIC_PORT_CMD_UPDATE_MAC = 164,
+	HINIC_PORT_CMD_UPDATE_MAC = 0xA4,
 
-	HINIC_PORT_CMD_GET_CAP          = 170,
+	HINIC_PORT_CMD_GET_CAP = 0xAA,
 
-	HINIC_PORT_CMD_GET_LINK_MODE	= 217,
+	HINIC_PORT_CMD_GET_LINK_MODE = 0xD9,
 
-	HINIC_PORT_CMD_SET_SPEED	= 218,
+	HINIC_PORT_CMD_SET_SPEED = 0xDA,
 
-	HINIC_PORT_CMD_SET_AUTONEG	= 219,
+	HINIC_PORT_CMD_SET_AUTONEG = 0xDB,
 
-	HINIC_PORT_CMD_GET_STD_SFP_INFO = 240,
+	HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0,
 
-	HINIC_PORT_CMD_SET_LRO_TIMER	= 244,
+	HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4,
 
-	HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 249,
+	HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9,
 
-	HINIC_PORT_CMD_GET_SFP_ABS	= 251,
+	HINIC_PORT_CMD_GET_SFP_ABS = 0xFB,
 };
 
 /* cmd of mgmt CPU message for HILINK module */
Signature · 1 line
2.25.1
author maintainer
#1 lore raw

PATCH v4 2/3 net: hinic: Add control command support for VF PMD driver in DPDK

HINIC has a mailbox for PF-VF communication and the VF driver could send port control command to PF driver via mailbox.

The control command only can be set to register in PF, so add support in PF driver for VF PMD driver control command when VF PMD driver work with linux PF driver.

Then, no need to add handlers to nic_vf_cmd_msg_handler[], because the host driver just forwards it to the firmware. Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC) which will recv and deal with these commands.

---
v1->v2:
1.Update the commit messsage.
2.Add net-next prefix.
The comments link: https://lore.kernel.org/lkml/[email protected]/
v2->v3:
1.Merge PATCH 3/3 to this series.

 .../net/ethernet/huawei/hinic/hinic_hw_dev.h  | 66 +++++++++++++++++++
 .../net/ethernet/huawei/hinic/hinic_sriov.c   | 18 +++++
 2 files changed, 84 insertions(+)
drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h +66 -0
index 6dae116a11f8..6b5797e69781 100644
@@ -51,6 +51,9 @@ enum hinic_port_cmd {
 	HINIC_PORT_CMD_ADD_VLAN = 0x3,
 	HINIC_PORT_CMD_DEL_VLAN = 0x4,
 
+	HINIC_PORT_CMD_SET_ETS = 0x7,
+	HINIC_PORT_CMD_GET_ETS = 0x8,
+
 	HINIC_PORT_CMD_SET_PFC = 0x5,
 
 	HINIC_PORT_CMD_SET_MAC = 0x9,
@@ -59,6 +62,8 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_SET_RX_MODE = 0xC,
 
+	HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE = 0xD,
+
 	HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14,
 	HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15,
 
@@ -81,6 +86,7 @@ enum hinic_port_cmd {
 	HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25,
 
 	HINIC_PORT_CMD_SET_PORT_STATE = 0x29,
+	HINIC_PORT_CMD_GET_PORT_STATE = 0x30,
 
 	HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B,
 
@@ -100,17 +106,29 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_RSS_CFG = 0x42,
 
+	HINIC_PORT_CMD_GET_PHY_TYPE = 0x44,
+
 	HINIC_PORT_CMD_FWCTXT_INIT = 0x45,
 
 	HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48,
 	HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49,
 
+	HINIC_PORT_CMD_GET_JUMBO_FRAME_SIZE = 0x4A,
+	HINIC_PORT_CMD_SET_JUMBO_FRAME_SIZE = 0x4B,
+
 	HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E,
 
 	HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58,
 
+	HINIC_PORT_CMD_GET_PORT_TYPE = 0x5B,
+
 	HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D,
 
+	HINIC_PORT_CMD_GET_PORT_ID_BY_FUNC_ID = 0x5E,
+
+	HINIC_PORT_CMD_GET_DMA_CS = 0x64,
+	HINIC_PORT_CMD_SET_DMA_CS = 0x65,
+
 	HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66,
 
 	HINIC_PORT_CMD_SET_VF_RATE = 0x69,
@@ -125,25 +143,73 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73,
 
+	HINIC_PORT_CMD_SET_PFC_THD = 0x75,
+
 	HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0,
 
+	HINIC_PORT_CMD_SET_LOSSLESS_ETH	= 0xA3,
+
 	HINIC_PORT_CMD_UPDATE_MAC = 0xA4,
 
 	HINIC_PORT_CMD_GET_CAP = 0xAA,
 
+	HINIC_PORT_CMD_UP_TC_ADD_FLOW = 0xAF,
+	HINIC_PORT_CMD_UP_TC_DEL_FLOW = 0xB0,
+	HINIC_PORT_CMD_UP_TC_GET_FLOW = 0xB1,
+
+	HINIC_PORT_CMD_UP_TC_FLUSH_TCAM = 0xB2,
+
+	HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK = 0xB3,
+
+	HINIC_PORT_CMD_UP_TC_ENABLE = 0xB4,
+
+	HINIC_PORT_CMD_UP_TC_GET_TCAM_BLOCK = 0xB5,
+
+	HINIC_PORT_CMD_SET_IPSU_MAC = 0xCB,
+	HINIC_PORT_CMD_GET_IPSU_MAC = 0xCC,
+
+	HINIC_PORT_CMD_SET_XSFP_STATUS = 0xD4,
+
 	HINIC_PORT_CMD_GET_LINK_MODE = 0xD9,
 
 	HINIC_PORT_CMD_SET_SPEED = 0xDA,
 
 	HINIC_PORT_CMD_SET_AUTONEG = 0xDB,
 
+	HINIC_PORT_CMD_CLEAR_QP_RES = 0xDD,
+
+	HINIC_PORT_CMD_SET_SUPER_CQE = 0xDE,
+
+	HINIC_PORT_CMD_SET_VF_COS = 0xDF,
+	HINIC_PORT_CMD_GET_VF_COS = 0xE1,
+
+	HINIC_PORT_CMD_CABLE_PLUG_EVENT	= 0xE5,
+
+	HINIC_PORT_CMD_LINK_ERR_EVENT = 0xE6,
+
+	HINIC_PORT_CMD_SET_COS_UP_MAP = 0xE8,
+
+	HINIC_PORT_CMD_RESET_LINK_CFG = 0xEB,
+
 	HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0,
 
+	HINIC_PORT_CMD_FORCE_PKT_DROP = 0xF3,
+
 	HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4,
 
+	HINIC_PORT_CMD_SET_VHD_CFG = 0xF7,
+
+	HINIC_PORT_CMD_SET_LINK_FOLLOW = 0xF8,
+
 	HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9,
 
 	HINIC_PORT_CMD_GET_SFP_ABS = 0xFB,
+
+	HINIC_PORT_CMD_Q_FILTER	= 0xFC,
+
+	HINIC_PORT_CMD_TCAM_FILTER = 0xFE,
+
+	HINIC_PORT_CMD_SET_VLAN_FILTER = 0xFF,
 };
 
 /* cmd of mgmt CPU message for HILINK module */
drivers/net/ethernet/huawei/hinic/hinic_sriov.c +18 -0
index f7e05b41385b..ee357088d021 100644
@@ -489,6 +489,24 @@ static struct vf_cmd_check_handle nic_cmd_support_vf[] = {
 	{HINIC_PORT_CMD_UPDATE_MAC, hinic_mbox_check_func_id_8B},
 	{HINIC_PORT_CMD_GET_CAP, hinic_mbox_check_func_id_8B},
 	{HINIC_PORT_CMD_GET_LINK_MODE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_GET_VF_COS, NULL},
+	{HINIC_PORT_CMD_SET_VHD_CFG, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_VLAN_FILTER, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_Q_FILTER, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_TCAM_FILTER, NULL},
+	{HINIC_PORT_CMD_UP_TC_ADD_FLOW, NULL},
+	{HINIC_PORT_CMD_UP_TC_DEL_FLOW, NULL},
+	{HINIC_PORT_CMD_UP_TC_FLUSH_TCAM, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_UP_TC_ENABLE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_CABLE_PLUG_EVENT, NULL},
+	{HINIC_PORT_CMD_LINK_ERR_EVENT, NULL},
+	{HINIC_PORT_CMD_SET_PORT_STATE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_ETS, NULL},
+	{HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE, NULL},
+	{HINIC_PORT_CMD_RESET_LINK_CFG, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_LINK_FOLLOW, NULL},
+	{HINIC_PORT_CMD_CLEAR_QP_RES, NULL},
 };
 
 #define CHECK_IPSU_15BIT	0X8000
Signature · 1 line
2.25.1
author maintainer
#2 lore raw

PATCH v4 3/3 net: hinic: Add support for configuration of rx-vlan-filter by ethtool

In reply to Cai Huoqing

When ethtool config rx-vlan-filter, the driver will send control command to firmware, then set to hardware in this patch.

---
v1->v3:

	1.Merge this patch to the series.
	comments link: https://lore.kernel.org/lkml/[email protected]/
 .../net/ethernet/huawei/hinic/hinic_main.c    | 10 ++++++
 .../net/ethernet/huawei/hinic/hinic_port.c    | 33 +++++++++++++++++++
 .../net/ethernet/huawei/hinic/hinic_port.h    | 12 +++++++
 3 files changed, 55 insertions(+)
drivers/net/ethernet/huawei/hinic/hinic_main.c +10 -0
index 9d4d795e1081..977c41473ab7 100644
@@ -1092,6 +1092,16 @@ static int set_features(struct hinic_dev *nic_dev,
 		}
 	}
 
+	if (changed & NETIF_F_HW_VLAN_CTAG_FILTER) {
+		ret = hinic_set_vlan_fliter(nic_dev,
+					    !!(features &
+					       NETIF_F_HW_VLAN_CTAG_FILTER));
+		if (ret) {
+			err = ret;
+			failed_features |= NETIF_F_HW_VLAN_CTAG_FILTER;
+		}
+	}
+
 	if (err) {
 		nic_dev->netdev->features = features ^ failed_features;
 		return -EIO;
drivers/net/ethernet/huawei/hinic/hinic_port.c +33 -0
index 0a39c3dffa9a..9406237c461e 100644
@@ -447,6 +447,39 @@ int hinic_set_rx_vlan_offload(struct hinic_dev *nic_dev, u8 en)
 	return 0;
 }
 
+int hinic_set_vlan_fliter(struct hinic_dev *nic_dev, u32 en)
+{
+	struct hinic_hwdev *hwdev = nic_dev->hwdev;
+	struct hinic_hwif *hwif = hwdev->hwif;
+	struct pci_dev *pdev = hwif->pdev;
+	struct hinic_vlan_filter vlan_filter;
+	u16 out_size = sizeof(vlan_filter);
+	int err;
+
+	if (!hwdev)
+		return -EINVAL;
+
+	vlan_filter.func_idx = HINIC_HWIF_FUNC_IDX(hwif);
+	vlan_filter.enable = en;
+
+	err = hinic_port_msg_cmd(hwdev, HINIC_PORT_CMD_SET_VLAN_FILTER,
+				 &vlan_filter, sizeof(vlan_filter),
+				 &vlan_filter, &out_size);
+	if (vlan_filter.status == HINIC_MGMT_CMD_UNSUPPORTED) {
+		err = HINIC_MGMT_CMD_UNSUPPORTED;
+	} else if ((err == HINIC_MBOX_VF_CMD_ERROR) &&
+			   HINIC_IS_VF(hwif)) {
+		err = HINIC_MGMT_CMD_UNSUPPORTED;
+	} else if (err || !out_size || vlan_filter.status) {
+		dev_err(&pdev->dev,
+			"Failed to set vlan fliter, err: %d, status: 0x%x, out size: 0x%x\n",
+			err, vlan_filter.status, out_size);
+		err = -EINVAL;
+	}
+
+	return err;
+}
+
 int hinic_set_max_qnum(struct hinic_dev *nic_dev, u8 num_rqs)
 {
 	struct hinic_hwdev *hwdev = nic_dev->hwdev;
drivers/net/ethernet/huawei/hinic/hinic_port.h +12 -0
index c9ae3d4dc547..c8694ac7c702 100644
@@ -351,6 +351,16 @@ struct hinic_vlan_cfg {
 	u8      rsvd1[5];
 };
 
+struct hinic_vlan_filter {
+	u8	status;
+	u8	version;
+	u8	rsvd0[6];
+
+	u16	func_idx;
+	u8	rsvd1[2];
+	u32	enable;
+};
+
 struct hinic_rss_template_mgmt {
 	u8	status;
 	u8	version;
@@ -831,6 +841,8 @@ int hinic_get_vport_stats(struct hinic_dev *nic_dev,
 
 int hinic_set_rx_vlan_offload(struct hinic_dev *nic_dev, u8 en);
 
+int hinic_set_vlan_fliter(struct hinic_dev *nic_dev, u32 en);
+
 int hinic_get_mgmt_version(struct hinic_dev *nic_dev, u8 *mgmt_ver);
 
 int hinic_set_link_settings(struct hinic_hwdev *hwdev,
Signature · 1 line
2.25.1
#3 lore raw
In reply to Cai Huoqing
This series was applied to netdev/net-next.git (master) by David S. Miller <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (master) by David S. Miller <[email protected]>:

Quoted 14 lines · On Thu, 3 Nov 2022 16:05:09 +0800 you wrote:

The print cmd code is in hex, so using hex cmd code intead of decimal is easy to check the value with print info.

---
v1->v2:

	1.Add net-next prefix.
	The comments link: https://lore.kernel.org/lkml/[email protected]/
v2->v3:
	1.Merge PATCH 3/3 to this series.
v3->v4:
	1.Revert the empty lines.
	The comments link: https://lore.kernel.org/lkml/[email protected]/
Quoted 1 line

[...]

Here is the summary with links:
- [net-next,v4,1/3] net: hinic: Convert the cmd code from decimal to hex to be more readable

    https://git.kernel.org/netdev/net-next/c/ac33d7ae8f71
  - [net-next,v4,2/3] net: hinic: Add control command support for VF PMD driver in DPDK
    https://git.kernel.org/netdev/net-next/c/13265568a863
  - [net-next,v4,3/3] net: hinic: Add support for configuration of rx-vlan-filter by ethtool
    https://git.kernel.org/netdev/net-next/c/2acf960e3be6

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html