mlx5 fixes 2022-11-02
Subsystems (5)
From: Saeed Mahameed <[email protected]>
v1->v2:
- Fix 32bit build issue.
This series provides bug fixes to mlx5 driver. Please pull and let me know if there is any problem.
Thanks,
Saeed.
The following changes since commit b7cbc6740bd6ad5d43345a2504f7e4beff0d709f:
net: fman: Unregister ethernet device on removal (2022-11-04 19:33:38 -0700)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git tags/mlx5-fixes-2022-11-02
for you to fetch changes up to 4a1ed426f330a544f8b56c2e4fae6a8c4fa77ccd:
net/mlx5e: TC, Fix slab-out-of-bounds in parse_tc_actions (2022-11-05 00:04:34 -0700)
----------------------------------------------------------------
mlx5-fixes-2022-11-02
----------------------------------------------------------------
Chris Mi (1):
net/mlx5: E-switch, Set to legacy mode if failed to change switchdev mode
Jianbo Liu (1):
net/mlx5e: TC, Fix wrong rejection of packet-per-second policing
Maxim Mikityanskiy (2):
net/mlx5e: Add missing sanity checks for max TX WQE size net/mlx5e: Fix usage of DMA sync API
Moshe Shemesh (1):
net/mlx5: Fix possible deadlock on mlx5e_tx_timeout_work
Roi Dayan (3):
net/mlx5e: Fix tc acts array not to be dependent on enum order net/mlx5e: E-Switch, Fix comparing termination table instance net/mlx5e: TC, Fix slab-out-of-bounds in parse_tc_actions
Roy Novich (1):
net/mlx5: Allow async trigger completion execution on single CPU systems
Shay Drory (1):
net/mlx5: fw_reset: Don't try to load device in case PCI isn't working
Vlad Buslov (1):
net/mlx5: Bridge, verify LAG state when adding bond to bridge
drivers/net/ethernet/mellanox/mlx5/core/cmd.c | 11 ++- .../ethernet/mellanox/mlx5/core/en/rep/bridge.c | 31 ++++++++ .../ethernet/mellanox/mlx5/core/en/tc/act/act.c | 92 ++++++++-------------- drivers/net/ethernet/mellanox/mlx5/core/en/txrx.h | 24 +++++- drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c | 4 +- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 13 ++- drivers/net/ethernet/mellanox/mlx5/core/en_rx.c | 27 ++++--- drivers/net/ethernet/mellanox/mlx5/core/en_tc.c | 14 ++-- drivers/net/ethernet/mellanox/mlx5/core/en_tx.c | 5 ++ drivers/net/ethernet/mellanox/mlx5/core/eswitch.c | 14 ++-- .../ethernet/mellanox/mlx5/core/eswitch_offloads.c | 18 +---- .../mellanox/mlx5/core/eswitch_offloads_termtbl.c | 14 ++-- drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c | 3 +- 13 files changed, 153 insertions(+), 117 deletions(-)
PATCH v2 1/11 net/mlx5: Bridge, verify LAG state when adding bond to bridge
From: Vlad Buslov <[email protected]>
Mlx5 LAG is initialized asynchronously on a workqueue which means that for a brief moment after setting mlx5 UL representors as lower devices of a bond netdevice the LAG itself is not fully initialized in the driver. When adding such bond device to a bridge mlx5 bridge code will not consider it as offload-capable, skip creating necessary bookkeeping and fail any further bridge offload-related commands with it (setting VLANs, offloading FDBs, etc.). In order to make the error explicit during bridge initialization stage implement the code that detects such condition during NETDEV_PRECHANGEUPPER event and returns an error.
--- .../mellanox/mlx5/core/en/rep/bridge.c | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+)
drivers/net/ethernet/mellanox/mlx5/core/en/rep/bridge.c +31 -0
@@ -164,6 +164,36 @@ static int mlx5_esw_bridge_port_changeupper(struct notifier_block *nb, void *ptrreturn err; } +static int +mlx5_esw_bridge_changeupper_validate_netdev (void *ptr) +{ +struct net_device *dev =netdev_notifier_info_to_dev (ptr); +struct netdev_notifier_changeupper_info *info = ptr; +struct net_device *upper = info->upper_dev; +struct net_device *lower; +struct list_head *iter; + +if (!netif_is_bridge_master (upper) || !netif_is_lag_master (dev)) +return 0 ; + +netdev_for_each_lower_dev (dev, lower, iter) { +struct mlx5_core_dev *mdev; +struct mlx5e_priv *priv; + +if (!mlx5e_eswitch_rep (lower)) +continue ; + + priv =netdev_priv (lower); + mdev = priv->mdev; +if (!mlx5_lag_is_active (mdev)) +return -EAGAIN ; +if (!mlx5_lag_is_shared_fdb (mdev)) +return -EOPNOTSUPP ; + } + +return 0 ; +} +static int mlx5_esw_bridge_switchdev_port_event (struct notifier_block *nb,unsigned long event,void *ptr) {
@@ -171,6 +201,7 @@ static int mlx5_esw_bridge_switchdev_port_event(struct notifier_block *nb,switch (event) {case NETDEV_PRECHANGEUPPER : + err =mlx5_esw_bridge_changeupper_validate_netdev (ptr);break ;case NETDEV_CHANGEUPPER :
Signature · 1 line
2.38.1
PATCH v2 2/11 net/mlx5: Allow async trigger completion execution on single CPU systems
In reply to Saeed MahameedFrom: Roy Novich <[email protected]>
For a single CPU system, the kernel thread executing mlx5_cmd_flush() never releases the CPU but calls down_trylock(&cmd→sem) in a busy loop. On a single processor system, this leads to a deadlock as the kernel thread which executes mlx5_cmd_invoke() never gets scheduled. Fix this, by adding the cond_resched() call to the loop, allow the command completion kernel thread to execute.
--- drivers/net/ethernet/mellanox/mlx5/core/cmd.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/cmd.c +8 -3
@@ -1770,12 +1770,17 @@ void mlx5_cmd_flush(struct mlx5_core_dev *dev)struct mlx5_cmd *cmd = &dev->cmd;int i; -for (i =0 ; i < cmd->max_reg_cmds; i++) -while (down_trylock (&cmd->sem)) +for (i =0 ; i < cmd->max_reg_cmds; i++) { +while (down_trylock (&cmd->sem)) {mlx5_cmd_trigger_completions (dev); +cond_resched (); + } + } -while (down_trylock (&cmd->pages_sem)) +while (down_trylock (&cmd->pages_sem)) {mlx5_cmd_trigger_completions (dev); +cond_resched (); + }/* Unlock cmdif */ up (&cmd->pages_sem);
Signature · 1 line
2.38.1
PATCH v2 3/11 net/mlx5: E-switch, Set to legacy mode if failed to change switchdev mode
In reply to Saeed MahameedFrom: Chris Mi <[email protected]>
No need to rollback to the other mode because probably will fail again. Just set to legacy mode and clear fdb table created flag. So that fdb table will not be cleared again.
--- .../net/ethernet/mellanox/mlx5/core/eswitch.c | 14 ++++++++------ .../mellanox/mlx5/core/eswitch_offloads.c | 18 +++--------------- 2 files changed, 11 insertions(+), 21 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/eswitch.c +8 -6
@@ -1387,12 +1387,14 @@ void mlx5_eswitch_disable_locked(struct mlx5_eswitch *esw) esw->mode ==MLX5_ESWITCH_LEGACY ?"LEGACY" :"OFFLOADS" , esw->esw_funcs.num_vfs, esw->enabled_vports); - esw->fdb_table.flags &= ~MLX5_ESW_FDB_CREATED ; -if (esw->mode ==MLX5_ESWITCH_OFFLOADS ) -esw_offloads_disable (esw); -else if (esw->mode ==MLX5_ESWITCH_LEGACY ) -esw_legacy_disable (esw); -mlx5_esw_acls_ns_cleanup (esw); +if (esw->fdb_table.flags &MLX5_ESW_FDB_CREATED ) { + esw->fdb_table.flags &= ~MLX5_ESW_FDB_CREATED ; +if (esw->mode ==MLX5_ESWITCH_OFFLOADS ) +esw_offloads_disable (esw); +else if (esw->mode ==MLX5_ESWITCH_LEGACY ) +esw_legacy_disable (esw); +mlx5_esw_acls_ns_cleanup (esw); + }if (esw->mode ==MLX5_ESWITCH_OFFLOADS )devl_rate_nodes_destroy (devlink);
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c +3 -15
@@ -2310,7 +2310,7 @@ static int esw_create_restore_table(struct mlx5_eswitch *esw)static int esw_offloads_start (struct mlx5_eswitch *esw,struct netlink_ext_ack *extack) { -int err, err1; +int err; esw->mode =MLX5_ESWITCH_OFFLOADS ; err =mlx5_eswitch_enable_locked (esw, esw->dev->priv.sriov.num_vfs);
@@ -2318,11 +2318,6 @@ static int esw_offloads_start(struct mlx5_eswitch *esw,NL_SET_ERR_MSG_MOD (extack,"Failed setting eswitch to offloads" ); esw->mode =MLX5_ESWITCH_LEGACY ; - err1 =mlx5_eswitch_enable_locked (esw,MLX5_ESWITCH_IGNORE_NUM_VFS ); -if (err1) { -NL_SET_ERR_MSG_MOD (extack, -"Failed setting eswitch back to legacy" ); - }mlx5_rescan_drivers (esw->dev); }if (esw->offloads.inline_mode ==MLX5_INLINE_MODE_NONE ) {
@@ -3389,19 +3384,12 @@ int esw_offloads_enable(struct mlx5_eswitch *esw)static int esw_offloads_stop (struct mlx5_eswitch *esw,struct netlink_ext_ack *extack) { -int err, err1; +int err; esw->mode =MLX5_ESWITCH_LEGACY ; err =mlx5_eswitch_enable_locked (esw,MLX5_ESWITCH_IGNORE_NUM_VFS ); -if (err) { +if (err)NL_SET_ERR_MSG_MOD (extack,"Failed setting eswitch to legacy" ); - esw->mode =MLX5_ESWITCH_OFFLOADS ; - err1 =mlx5_eswitch_enable_locked (esw,MLX5_ESWITCH_IGNORE_NUM_VFS ); -if (err1) { -NL_SET_ERR_MSG_MOD (extack, -"Failed setting eswitch back to offloads" ); - } - }return err; }
Signature · 1 line
2.38.1
PATCH v2 4/11 net/mlx5: fw_reset: Don't try to load device in case PCI isn't working
In reply to Saeed MahameedFrom: Shay Drory <[email protected]>
In case PCI reads fail after unload, there is no use in trying to load the device.
--- drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c +2 -1
@@ -152,7 +152,8 @@ static void mlx5_fw_reset_complete_reload(struct mlx5_core_dev *dev)mlx5_unload_one (dev);if (mlx5_health_wait_pci_up (dev))mlx5_core_err (dev,"reset reload flow aborted, PCI reads still not working\n" ); -mlx5_load_one (dev, false); +else +mlx5_load_one (dev, false);devlink_remote_reload_actions_performed (priv_to_devlink (dev),0 ,BIT (DEVLINK_RELOAD_ACTION_DRIVER_REINIT ) |BIT (DEVLINK_RELOAD_ACTION_FW_ACTIVATE ));
Signature · 1 line
2.38.1
PATCH v2 5/11 net/mlx5: Fix possible deadlock on mlx5e_tx_timeout_work
In reply to Saeed MahameedFrom: Moshe Shemesh <[email protected]>
Due to the cited patch, devlink health commands take devlink lock and this may result in deadlock for mlx5e_tx_reporter as it takes local state_lock before calling devlink health report and on the other hand devlink health commands such as diagnose for same reporter take local state_lock after taking devlink lock (see kernel log below).
To fix it, remove local state_lock from mlx5e_tx_timeout_work() before calling devlink_health_report() and take care to cancel the work before any call to close channels, which may free the SQs that should be handled by the work. Before cancel_work_sync(), use current_work() to check we are not calling it from within the work, as mlx5e_tx_timeout_work() itself may close the channels and reopen as part of recovery flow.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1 Not tainted
------------------------------------------------------
kworker/u16:2/65 is trying to acquire lock:ffff888122f6c2f8 (&devlink->lock_key#2){+.+.}-{3:3}, at: devlink_health_report+0x2f1/0x7e0
but task is already holding lock:ffff888121d20be0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&priv->state_lock){+.+.}-{3:3}:
__mutex_lock+0x12c/0x14b0
mlx5e_rx_reporter_diagnose+0x71/0x700 [mlx5_core]
devlink_nl_cmd_health_reporter_diagnose_doit+0x212/0xa50
genl_family_rcv_msg_doit+0x1e9/0x2f0
genl_rcv_msg+0x2e9/0x530
netlink_rcv_skb+0x11d/0x340
genl_rcv+0x24/0x40
netlink_unicast+0x438/0x710
netlink_sendmsg+0x788/0xc40
sock_sendmsg+0xb0/0xe0
__sys_sendto+0x1c1/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0-> #0 (&devlink->lock_key#2){+.+.}-{3:3}:
__lock_acquire+0x2c8a/0x6200
lock_acquire+0x1c1/0x550
__mutex_lock+0x12c/0x14b0
devlink_health_report+0x2f1/0x7e0
mlx5e_health_report+0xc9/0xd7 [mlx5_core]
mlx5e_reporter_tx_timeout+0x2ab/0x3d0 [mlx5_core]
mlx5e_tx_timeout_work+0x1c1/0x280 [mlx5_core]
process_one_work+0x7c2/0x1340
worker_thread+0x59d/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&priv->state_lock);
lock(&devlink->lock_key#2);
lock(&priv->state_lock); lock(&devlink->lock_key#2);
*** DEADLOCK ***
4 locks held by kworker/u16:2/65:
#0: ffff88811a55b138 ((wq_completion)mlx5e#2){+.+.}-{0:0}, at: process_one_work+0x6e2/0x1340 #1: ffff888101de7db8 ((work_completion)(&priv->tx_timeout_work)){+.+.}-{0:0}, at: process_one_work+0x70f/0x1340 #2: ffffffff84ce8328 (rtnl_mutex){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x53/0x280 [mlx5_core] #3: ffff888121d20be0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
stack backtrace: CPU: 1 PID: 65 Comm: kworker/u16:2 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core] Call Trace: <TASK> dump_stack_lvl+0x57/0x7d check_noncircular+0x278/0x300 ? print_circular_bug+0x460/0x460 ? find_held_lock+0x2d/0x110 ? __stack_depot_save+0x24c/0x520 ? alloc_chain_hlocks+0x228/0x700 __lock_acquire+0x2c8a/0x6200 ? register_lock_class+0x1860/0x1860 ? kasan_save_stack+0x1e/0x40 ? kasan_set_free_info+0x20/0x30 ? ____kasan_slab_free+0x11d/0x1b0 ? kfree+0x1ba/0x520 ? devlink_health_do_dump.part.0+0x171/0x3a0 ? devlink_health_report+0x3d5/0x7e0 lock_acquire+0x1c1/0x550 ? devlink_health_report+0x2f1/0x7e0 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? find_held_lock+0x2d/0x110 __mutex_lock+0x12c/0x14b0 ? devlink_health_report+0x2f1/0x7e0 ? devlink_health_report+0x2f1/0x7e0 ? mutex_lock_io_nested+0x1320/0x1320 ? trace_hardirqs_on+0x2d/0x100 ? bit_wait_io_timeout+0x170/0x170 ? devlink_health_do_dump.part.0+0x171/0x3a0 ? kfree+0x1ba/0x520 ? devlink_health_do_dump.part.0+0x171/0x3a0 devlink_health_report+0x2f1/0x7e0 mlx5e_health_report+0xc9/0xd7 [mlx5_core] mlx5e_reporter_tx_timeout+0x2ab/0x3d0 [mlx5_core] ? lockdep_hardirqs_on_prepare+0x400/0x400 ? mlx5e_reporter_tx_err_cqe+0x1b0/0x1b0 [mlx5_core] ? mlx5e_tx_reporter_timeout_dump+0x70/0x70 [mlx5_core] ? mlx5e_tx_reporter_dump_sq+0x320/0x320 [mlx5_core] ? mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core] ? mutex_lock_io_nested+0x1320/0x1320 ? process_one_work+0x70f/0x1340 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? lock_downgrade+0x6e0/0x6e0 mlx5e_tx_timeout_work+0x1c1/0x280 [mlx5_core] process_one_work+0x7c2/0x1340 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? pwq_dec_nr_in_flight+0x230/0x230 ? rwlock_bug.part.0+0x90/0x90 worker_thread+0x59d/0xec0 ? process_one_work+0x1340/0x1340 kthread+0x28f/0x330 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK>
--- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +4 -2
@@ -2954,6 +2954,9 @@ static int mlx5e_switch_priv_channels(struct mlx5e_priv *priv,netif_carrier_off (netdev);mlx5e_deactivate_priv_channels (priv); +/* Once deactivated, new tx_timeout_work won't be initiated. */ +if (current_work () != &priv->tx_timeout_work) +cancel_work_sync (&priv->tx_timeout_work); old_chs = priv->channels; priv->channels = *new_chs;
@@ -3106,6 +3109,7 @@ int mlx5e_close_locked(struct net_device *netdev)netif_carrier_off (priv->netdev);mlx5e_deactivate_priv_channels (priv); +cancel_work_sync (&priv->tx_timeout_work);mlx5e_close_channels (&priv->channels);return 0 ;
@@ -4657,7 +4661,6 @@ static void mlx5e_tx_timeout_work(struct work_struct *work)int i;rtnl_lock (); -mutex_lock (&priv->state_lock);if (!test_bit (MLX5E_STATE_OPENED , &priv->state)) goto unlock;
@@ -4676,7 +4679,6 @@ static void mlx5e_tx_timeout_work(struct work_struct *work) } unlock: -mutex_unlock (&priv->state_lock);rtnl_unlock (); }
Signature · 1 line
2.38.1
Jakub Kicinski
maintainerRe: [V2 net 05/11] net/mlx5: Fix possible deadlock on mlx5e_tx_timeout_work
drivers/net/ethernet/mellanox/mlx5/core/en_main.c static int mlx5e_switch_priv_channels(struct mlx5e_priv *priv, · line 2959
Quoted 3 lines · On Sat, 5 Nov 2022 00:10:22 -0700 Saeed Mahameed wrote:
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +3
-0+/* Once deactivated, new tx_timeout_work won't be initiated. */ +if (current_work () != &priv->tx_timeout_work) +cancel_work_sync (&priv->tx_timeout_work);
The work takes rtnl_lock, are there no callers of mlx5e_switch_priv_channels() that are under rtnl_lock()?
This patch is definitely going onto my "expecting Fixes" bingo card :S
Paolo Abeni
maintainerRe: [V2 net 05/11] net/mlx5: Fix possible deadlock on mlx5e_tx_timeout_work
Quoted 10 lines · Jakub Kicinski
drivers/net/ethernet/mellanox/mlx5/core/en_main.c static int mlx5e_switch_priv_channels(struct mlx5e_priv *priv, · line 2959
Quoted 3 lines · On Sat, 5 Nov 2022 00:10:22 -0700 Saeed Mahameed wrote:
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +3
-0+/* Once deactivated, new tx_timeout_work won't be initiated. */ +if (current_work () != &priv->tx_timeout_work) +cancel_work_sync (&priv->tx_timeout_work);The work takes
rtnl_lock, are there no callers ofmlx5e_switch_priv_channels()that are underrtnl_lock()?This patch is definitely going onto my "expecting Fixes" bingo card :S
I think Jakub is right and even mlx5e_close_locked() will deadlock on cancel_work_sync() if the work is scheduled but it has not yet acquired the rtnl lock.
IIRC lockdep is not able to catch this kind of situation, so you can only observe the deadlock when reaching the critical scenario.
I'm wild guessing than a possible solution would be restrict the state_lock scope in mlx5e_tx_timeout_work() around the state check, without additional cancel_work operations.
Thanks,
Paolo
Re: [V2 net 05/11] net/mlx5: Fix possible deadlock on mlx5e_tx_timeout_work
Quoted 9 lines · Paolo Abeni
Quoted 8 lines · Jakub Kicinski
drivers/net/ethernet/mellanox/mlx5/core/en_main.c static int mlx5e_switch_priv_channels(struct mlx5e_priv *priv, · line 2959
Quoted 3 lines · On Sat, 5 Nov 2022 00:10:22 -0700 Saeed Mahameed wrote:
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +3
-0+/* Once deactivated, new tx_timeout_work won't be initiated. */ +if (current_work () != &priv->tx_timeout_work) +cancel_work_sync (&priv->tx_timeout_work);The work takes
rtnl_lock, are there no callers ofmlx5e_switch_priv_channels()that are underrtnl_lock()?
Quoted 6 lines
Quoted 2 lines
This patch is definitely going onto my "expecting Fixes" bingo card :S
I think Jakub is right and even
mlx5e_close_locked()will deadlock oncancel_work_sync()if the work is scheduled but it has not yet acquired the rtnl lock.
Yes you are absolutely correct, you can see the deadlock just by looking at the patch diff and applying common sense that mlx5e_switch_priv_channels() is being called under rtnl.
Quoted 8 lines
IIRC lockdep is not able to catch this kind of situation, so you can only observe the deadlock when reaching the critical scenario.
I'm wild guessing than a possible solution would be restrict the
state_lockscope inmlx5e_tx_timeout_work()around the state check, without additionalcancel_workoperations.
Thanks, i will drop the patch for now and send v3 without it.
Quoted 4 lines
Thanks,
Paolo
PATCH v2 6/11 net/mlx5e: Add missing sanity checks for max TX WQE size
In reply to Saeed MahameedFrom: Maxim Mikityanskiy <[email protected]>
The commit cited below started using the firmware capability for the maximum TX WQE size. This commit adds an important check to verify that the driver doesn't attempt to exceed this capability, and also restores another check mistakenly removed in the cited commit (a WQE must not exceed the page size).
--- .../net/ethernet/mellanox/mlx5/core/en/txrx.h | 24 ++++++++++++++++++- .../net/ethernet/mellanox/mlx5/core/en_main.c | 7 ++++++ .../net/ethernet/mellanox/mlx5/core/en_tx.c | 5 ++++ 3 files changed, 35 insertions(+), 1 deletion(-)
drivers/net/ethernet/mellanox/mlx5/core/en/txrx.h +23 -1
@@ -11,6 +11,27 @@#define INL_HDR_START_SZ (sizeof(((struct mlx5_wqe_eth_seg *)NULL)->inline_hdr.start)) +/* IPSEC inline data includes: +* 1. ESP trailer: up to 255 bytes of padding, 1 byte for pad length, 1 byte for +* next header. +* 2. ESP authentication data: 16 bytes for ICV. +*/ +#define MLX5E_MAX_TX_IPSEC_DS DIV_ROUND_UP(sizeof(struct mlx5_wqe_inline_seg) + \ + 255 + 1 + 1 + 16, MLX5_SEND_WQE_DS) + +/* 366 should be big enough to cover all L2, L3 and L4 headers with possible +* encapsulations. +*/ +#define MLX5E_MAX_TX_INLINE_DS DIV_ROUND_UP(366 - INL_HDR_START_SZ + VLAN_HLEN, \ + MLX5_SEND_WQE_DS) + +/* Sync the calculation with mlx5e_sq_calc_wqe_attr. */ +#define MLX5E_MAX_TX_WQEBBS DIV_ROUND_UP(MLX5E_TX_WQE_EMPTY_DS_COUNT + \ + MLX5E_MAX_TX_INLINE_DS + \ + MLX5E_MAX_TX_IPSEC_DS + \ + MAX_SKB_FRAGS + 1, \ + MLX5_SEND_WQEBB_NUM_DS) +#define MLX5E_RX_ERR_CQE (cqe) (get_cqe_opcode(cqe) != MLX5_CQE_RESP_SEND) static inline
@@ -424,6 +445,8 @@ mlx5e_set_eseg_swp(struct sk_buff *skb, struct mlx5_wqe_eth_seg *eseg,static inline u16 mlx5e_stop_room_for_wqe (struct mlx5_core_dev *mdev,u16 wqe_size) { +WARN_ON_ONCE (PAGE_SIZE /MLX5_SEND_WQE_BB <mlx5e_get_max_sq_wqebbs (mdev)); +/* A WQE must not cross the page boundary, hence two conditions: * 1. Its size must not exceed the page size. * 2. If the WQE size is X, and the space remaining in a page is less
@@ -436,7 +459,6 @@ static inline u16 mlx5e_stop_room_for_wqe(struct mlx5_core_dev *mdev, u16 wqe_si"wqe_size %u is greater than max SQ WQEBBs %u" , wqe_size, mlx5e_get_max_sq_wqebbs(mdev)); -return MLX5E_STOP_ROOM (wqe_size); }
drivers/net/ethernet/mellanox/mlx5/core/en_main.c +7 -0
@@ -5696,6 +5696,13 @@ int mlx5e_attach_netdev(struct mlx5e_priv *priv)mlx5e_fs_set_state_destroy (priv->fs, !test_bit (MLX5E_STATE_DESTROYING , &priv->state)); +/* Validate the max_wqe_size_sq capability. */ +if (WARN_ON_ONCE (mlx5e_get_max_sq_wqebbs (priv->mdev) <MLX5E_MAX_TX_WQEBBS )) { +mlx5_core_warn (priv->mdev,"MLX5E: Max SQ WQEBBs firmware capability: %u, needed %lu\n" , +mlx5e_get_max_sq_wqebbs (priv->mdev),MLX5E_MAX_TX_WQEBBS ); +return -EIO ; + } +/* max number of channels may have changed */ max_nch =mlx5e_calc_max_nch (priv->mdev, priv->netdev, profile);if (priv->channels.params.num_channels > max_nch) {
drivers/net/ethernet/mellanox/mlx5/core/en_tx.c +5 -0
@@ -305,6 +305,8 @@ static void mlx5e_sq_calc_wqe_attr(struct sk_buff *skb, const struct mlx5e_tx_atu16 ds_cnt_inl =0 ;u16 ds_cnt_ids =0 ; +/* Sync the calculation with MLX5E_MAX_TX_WQEBBS. */ +if (attr->insz) ds_cnt_ids =DIV_ROUND_UP (sizeof (struct mlx5_wqe_inline_seg ) + attr->insz,MLX5_SEND_WQE_DS );
@@ -317,6 +319,9 @@ static void mlx5e_sq_calc_wqe_attr(struct sk_buff *skb, const struct mlx5e_tx_at inl +=VLAN_HLEN ; ds_cnt_inl =DIV_ROUND_UP (inl,MLX5_SEND_WQE_DS ); +if (WARN_ON_ONCE (ds_cnt_inl >MLX5E_MAX_TX_INLINE_DS )) +netdev_warn (skb->dev,"ds_cnt_inl = %u > max %u\n" , ds_cnt_inl, + (u16 )MLX5E_MAX_TX_INLINE_DS ); ds_cnt += ds_cnt_inl; }
Signature · 1 line
2.38.1
PATCH v2 7/11 net/mlx5e: Fix usage of DMA sync API
In reply to Saeed MahameedFrom: Maxim Mikityanskiy <[email protected]>
DMA sync functions should use the same direction that was used by DMA mapping. Use DMA_BIDIRECTIONAL for XDP_TX from regular RQ, which reuses the same mapping that was used for RX, and DMA_TO_DEVICE for XDP_TX from XSK RQ and XDP_REDIRECT, which establish a new mapping in this direction. On the RX side, use the same direction that was used when setting up the mapping (DMA_BIDIRECTIONAL for XDP, DMA_FROM_DEVICE otherwise).
Also don't skip sync for device when establishing a DMA_FROM_DEVICE mapping for RX, as some architectures (ARM) may require invalidating caches before the device can use the mapping. It doesn't break the bugfix made in
commit 0b7cfa4082fb ("net/mlx5e: Fix page DMA map/unmap attributes"), since the bug happened on unmap.
--- .../net/ethernet/mellanox/mlx5/core/en/xdp.c | 4 +-- .../net/ethernet/mellanox/mlx5/core/en_rx.c | 27 ++++++++++--------- 2 files changed, 16 insertions(+), 15 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c +2 -2
@@ -117,7 +117,7 @@ mlx5e_xmit_xdp_buff(struct mlx5e_xdpsq *sq, struct mlx5e_rq *rq, xdpi.page.rq = rq; dma_addr =page_pool_get_dma_addr (page) + (xdpf->data - (void *)xdpf); -dma_sync_single_for_device (sq->pdev, dma_addr, xdptxd.len,DMA_TO_DEVICE ); +dma_sync_single_for_device (sq->pdev, dma_addr, xdptxd.len,DMA_BIDIRECTIONAL );if (unlikely (xdp_frame_has_frags (xdpf))) { sinfo =xdp_get_shared_info_from_frame (xdpf);
@@ -131,7 +131,7 @@ mlx5e_xmit_xdp_buff(struct mlx5e_xdpsq *sq, struct mlx5e_rq *rq,skb_frag_off (frag); len =skb_frag_size (frag);dma_sync_single_for_device (sq->pdev, addr, len, -DMA_TO_DEVICE ); +DMA_BIDIRECTIONAL ); } }
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c +14 -13
@@ -266,7 +266,7 @@ static inline bool mlx5e_rx_cache_get(struct mlx5e_rq *rq, union mlx5e_alloc_uni addr =page_pool_get_dma_addr (au->page);/* Non-XSK always uses PAGE_SIZE. */ -dma_sync_single_for_device (rq->pdev, addr,PAGE_SIZE ,DMA_FROM_DEVICE ); +dma_sync_single_for_device (rq->pdev, addr,PAGE_SIZE , rq->buff.map_dir);return true; }
@@ -282,8 +282,7 @@ static inline int mlx5e_page_alloc_pool(struct mlx5e_rq *rq, union mlx5e_alloc_ureturn -ENOMEM ;/* Non-XSK always uses PAGE_SIZE. */ - addr =dma_map_page_attrs (rq->pdev, au->page,0 ,PAGE_SIZE , - rq->buff.map_dir,DMA_ATTR_SKIP_CPU_SYNC ); + addr =dma_map_page (rq->pdev, au->page,0 ,PAGE_SIZE , rq->buff.map_dir);if (unlikely (dma_mapping_error (rq->pdev, addr))) {page_pool_recycle_direct (rq->page_pool, au->page); au->page =NULL ;
@@ -427,14 +426,15 @@ mlx5e_add_skb_frag(struct mlx5e_rq *rq, struct sk_buff *skb, {dma_addr_t addr =page_pool_get_dma_addr (au->page); -dma_sync_single_for_cpu (rq->pdev, addr + frag_offset, len,DMA_FROM_DEVICE ); +dma_sync_single_for_cpu (rq->pdev, addr + frag_offset, len, + rq->buff.map_dir);page_ref_inc (au->page);skb_add_rx_frag (skb,skb_shinfo (skb)->nr_frags, au->page, frag_offset, len, truesize); }static inline void -mlx5e_copy_skb_header (struct device *pdev,struct sk_buff *skb, +mlx5e_copy_skb_header (struct mlx5e_rq *rq,struct sk_buff *skb,struct page *page,dma_addr_t addr,int offset_from,int dma_offset,u32 headlen) {
@@ -442,7 +442,8 @@ mlx5e_copy_skb_header(struct device *pdev, struct sk_buff *skb,/* Aligning len to sizeof(long) optimizes memcpy performance */ unsigned int len =ALIGN (headlen,sizeof (long )); -dma_sync_single_for_cpu (pdev, addr + dma_offset, len,DMA_FROM_DEVICE ); +dma_sync_single_for_cpu (rq->pdev, addr + dma_offset, len, + rq->buff.map_dir);skb_copy_to_linear_data (skb, from, len); }
@@ -1538,7 +1539,7 @@ mlx5e_skb_from_cqe_linear(struct mlx5e_rq *rq, struct mlx5e_wqe_frag_info *wi, addr =page_pool_get_dma_addr (au->page);dma_sync_single_range_for_cpu (rq->pdev, addr, wi->offset, - frag_size,DMA_FROM_DEVICE ); + frag_size, rq->buff.map_dir);net_prefetch (data); prog =rcu_dereference (rq->xdp_prog);
@@ -1587,7 +1588,7 @@ mlx5e_skb_from_cqe_nonlinear(struct mlx5e_rq *rq, struct mlx5e_wqe_frag_info *wi addr =page_pool_get_dma_addr (au->page);dma_sync_single_range_for_cpu (rq->pdev, addr, wi->offset, - rq->buff.frame0_sz,DMA_FROM_DEVICE ); + rq->buff.frame0_sz, rq->buff.map_dir);net_prefetchw (va);/* xdp_frame data area */ net_prefetch (va + rx_headroom);
@@ -1608,7 +1609,7 @@ mlx5e_skb_from_cqe_nonlinear(struct mlx5e_rq *rq, struct mlx5e_wqe_frag_info *wi addr =page_pool_get_dma_addr (au->page);dma_sync_single_for_cpu (rq->pdev, addr + wi->offset, - frag_consumed_bytes,DMA_FROM_DEVICE ); + frag_consumed_bytes, rq->buff.map_dir);if (!xdp_buff_has_frags (&xdp)) {/* Init on the first fragment to avoid cold cache access
@@ -1905,7 +1906,7 @@ mlx5e_skb_from_cqe_mpwrq_nonlinear(struct mlx5e_rq *rq, struct mlx5e_mpw_info *wmlx5e_fill_skb_data (skb, rq, au, byte_cnt, frag_offset);/* copy header */ addr =page_pool_get_dma_addr (head_au->page); -mlx5e_copy_skb_header (rq->pdev, skb, head_au->page, addr, +mlx5e_copy_skb_header (rq, skb, head_au->page, addr, head_offset, head_offset, headlen);/* skb linear part was allocated with headlen and aligned to long */ skb->tail += headlen;
@@ -1939,7 +1940,7 @@ mlx5e_skb_from_cqe_mpwrq_linear(struct mlx5e_rq *rq, struct mlx5e_mpw_info *wi, addr =page_pool_get_dma_addr (au->page);dma_sync_single_range_for_cpu (rq->pdev, addr, head_offset, - frag_size,DMA_FROM_DEVICE ); + frag_size, rq->buff.map_dir);net_prefetch (data); prog =rcu_dereference (rq->xdp_prog);
@@ -1987,7 +1988,7 @@ mlx5e_skb_from_cqe_shampo(struct mlx5e_rq *rq, struct mlx5e_mpw_info *wi,if (likely (frag_size <=BIT (MLX5E_SHAMPO_LOG_MAX_HEADER_ENTRY_SIZE ))) {/* build SKB around header */ -dma_sync_single_range_for_cpu (rq->pdev, head->addr,0 , frag_size,DMA_FROM_DEVICE ); +dma_sync_single_range_for_cpu (rq->pdev, head->addr,0 , frag_size, rq->buff.map_dir);prefetchw (hdr);prefetch (data); skb =mlx5e_build_linear_skb (rq, hdr, frag_size, rx_headroom, head_size,0 );
@@ -2009,7 +2010,7 @@ mlx5e_skb_from_cqe_shampo(struct mlx5e_rq *rq, struct mlx5e_mpw_info *wi, }prefetchw (skb->data); -mlx5e_copy_skb_header (rq->pdev, skb, head->page, head->addr, +mlx5e_copy_skb_header (rq, skb, head->page, head->addr, head_offset + rx_headroom, rx_headroom, head_size);/* skb linear part was allocated with headlen and aligned to long */
Signature · 1 line
2.38.1
PATCH v2 8/11 net/mlx5e: Fix tc acts array not to be dependent on enum order
In reply to Saeed MahameedFrom: Roi Dayan <[email protected]>
The tc acts array should not be dependent on kernel internal flow action id enum. Fix the array initialization.
--- .../mellanox/mlx5/core/en/tc/act/act.c | 92 +++++++------------ 1 file changed, 32 insertions(+), 60 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.c +32 -60
@@ -6,70 +6,42 @@#include "en/tc_priv.h" #include "mlx5_core.h" -/* Must be aligned with enum flow_action_id. */ static struct mlx5e_tc_act *tc_acts_fdb[NUM_FLOW_ACTIONS ] = { - &mlx5e_tc_act_accept, - &mlx5e_tc_act_drop, - &mlx5e_tc_act_trap, - &mlx5e_tc_act_goto, - &mlx5e_tc_act_mirred, - &mlx5e_tc_act_mirred, - &mlx5e_tc_act_redirect_ingress, -NULL ,/* FLOW_ACTION_MIRRED_INGRESS, */ - &mlx5e_tc_act_vlan, - &mlx5e_tc_act_vlan, - &mlx5e_tc_act_vlan_mangle, - &mlx5e_tc_act_tun_encap, - &mlx5e_tc_act_tun_decap, - &mlx5e_tc_act_pedit, - &mlx5e_tc_act_pedit, - &mlx5e_tc_act_csum, -NULL ,/* FLOW_ACTION_MARK, */ - &mlx5e_tc_act_ptype, -NULL ,/* FLOW_ACTION_PRIORITY, */ -NULL ,/* FLOW_ACTION_WAKE, */ -NULL ,/* FLOW_ACTION_QUEUE, */ - &mlx5e_tc_act_sample, - &mlx5e_tc_act_police, - &mlx5e_tc_act_ct, -NULL ,/* FLOW_ACTION_CT_METADATA, */ - &mlx5e_tc_act_mpls_push, - &mlx5e_tc_act_mpls_pop, -NULL ,/* FLOW_ACTION_MPLS_MANGLE, */ -NULL ,/* FLOW_ACTION_GATE, */ -NULL ,/* FLOW_ACTION_PPPOE_PUSH, */ -NULL ,/* FLOW_ACTION_JUMP, */ -NULL ,/* FLOW_ACTION_PIPE, */ - &mlx5e_tc_act_vlan, - &mlx5e_tc_act_vlan, + [FLOW_ACTION_ACCEPT ] = &mlx5e_tc_act_accept, + [FLOW_ACTION_DROP ] = &mlx5e_tc_act_drop, + [FLOW_ACTION_TRAP ] = &mlx5e_tc_act_trap, + [FLOW_ACTION_GOTO ] = &mlx5e_tc_act_goto, + [FLOW_ACTION_REDIRECT ] = &mlx5e_tc_act_mirred, + [FLOW_ACTION_MIRRED ] = &mlx5e_tc_act_mirred, + [FLOW_ACTION_REDIRECT_INGRESS ] = &mlx5e_tc_act_redirect_ingress, + [FLOW_ACTION_VLAN_PUSH ] = &mlx5e_tc_act_vlan, + [FLOW_ACTION_VLAN_POP ] = &mlx5e_tc_act_vlan, + [FLOW_ACTION_VLAN_MANGLE ] = &mlx5e_tc_act_vlan_mangle, + [FLOW_ACTION_TUNNEL_ENCAP ] = &mlx5e_tc_act_tun_encap, + [FLOW_ACTION_TUNNEL_DECAP ] = &mlx5e_tc_act_tun_decap, + [FLOW_ACTION_MANGLE ] = &mlx5e_tc_act_pedit, + [FLOW_ACTION_ADD ] = &mlx5e_tc_act_pedit, + [FLOW_ACTION_CSUM ] = &mlx5e_tc_act_csum, + [FLOW_ACTION_PTYPE ] = &mlx5e_tc_act_ptype, + [FLOW_ACTION_SAMPLE ] = &mlx5e_tc_act_sample, + [FLOW_ACTION_POLICE ] = &mlx5e_tc_act_police, + [FLOW_ACTION_CT ] = &mlx5e_tc_act_ct, + [FLOW_ACTION_MPLS_PUSH ] = &mlx5e_tc_act_mpls_push, + [FLOW_ACTION_MPLS_POP ] = &mlx5e_tc_act_mpls_pop, + [FLOW_ACTION_VLAN_PUSH_ETH ] = &mlx5e_tc_act_vlan, + [FLOW_ACTION_VLAN_POP_ETH ] = &mlx5e_tc_act_vlan, }; -/* Must be aligned with enum flow_action_id. */ static struct mlx5e_tc_act *tc_acts_nic[NUM_FLOW_ACTIONS ] = { - &mlx5e_tc_act_accept, - &mlx5e_tc_act_drop, -NULL ,/* FLOW_ACTION_TRAP, */ - &mlx5e_tc_act_goto, - &mlx5e_tc_act_mirred_nic, -NULL ,/* FLOW_ACTION_MIRRED, */ -NULL ,/* FLOW_ACTION_REDIRECT_INGRESS, */ -NULL ,/* FLOW_ACTION_MIRRED_INGRESS, */ -NULL ,/* FLOW_ACTION_VLAN_PUSH, */ -NULL ,/* FLOW_ACTION_VLAN_POP, */ -NULL ,/* FLOW_ACTION_VLAN_MANGLE, */ -NULL ,/* FLOW_ACTION_TUNNEL_ENCAP, */ -NULL ,/* FLOW_ACTION_TUNNEL_DECAP, */ - &mlx5e_tc_act_pedit, - &mlx5e_tc_act_pedit, - &mlx5e_tc_act_csum, - &mlx5e_tc_act_mark, -NULL ,/* FLOW_ACTION_PTYPE, */ -NULL ,/* FLOW_ACTION_PRIORITY, */ -NULL ,/* FLOW_ACTION_WAKE, */ -NULL ,/* FLOW_ACTION_QUEUE, */ -NULL ,/* FLOW_ACTION_SAMPLE, */ -NULL ,/* FLOW_ACTION_POLICE, */ - &mlx5e_tc_act_ct, + [FLOW_ACTION_ACCEPT ] = &mlx5e_tc_act_accept, + [FLOW_ACTION_DROP ] = &mlx5e_tc_act_drop, + [FLOW_ACTION_GOTO ] = &mlx5e_tc_act_goto, + [FLOW_ACTION_REDIRECT ] = &mlx5e_tc_act_mirred_nic, + [FLOW_ACTION_MANGLE ] = &mlx5e_tc_act_pedit, + [FLOW_ACTION_ADD ] = &mlx5e_tc_act_pedit, + [FLOW_ACTION_CSUM ] = &mlx5e_tc_act_csum, + [FLOW_ACTION_MARK ] = &mlx5e_tc_act_mark, + [FLOW_ACTION_CT ] = &mlx5e_tc_act_ct, };/**
Signature · 1 line
2.38.1
PATCH v2 9/11 net/mlx5e: TC, Fix wrong rejection of packet-per-second policing
In reply to Saeed MahameedFrom: Jianbo Liu <[email protected]>
In the bellow commit, we added support for PPS policing without removing the check which block offload of such cases. Fix it by removing this check.
--- drivers/net/ethernet/mellanox/mlx5/core/en_tc.c | 6 ------ 1 file changed, 6 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c +0 -6
@@ -4758,12 +4758,6 @@ int mlx5e_policer_validate(const struct flow_action *action,return -EOPNOTSUPP ; } -if (act->police.rate_pkt_ps) { -NL_SET_ERR_MSG_MOD (extack, -"QoS offload not support packets per second" ); -return -EOPNOTSUPP ; - } -return 0 ; }
Signature · 1 line
2.38.1
PATCH v2 10/11 net/mlx5e: E-Switch, Fix comparing termination table instance
In reply to Saeed MahameedFrom: Roi Dayan <[email protected]>
The pkt_reformat pointer being saved under flow_act and not dest attribute in the termination table instance. Fix the comparison pointers.
Also fix returning success if one pkt_reformat pointer is null and the other is not.
--- .../mellanox/mlx5/core/eswitch_offloads_termtbl.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c +8 -6
@@ -30,9 +30,9 @@ mlx5_eswitch_termtbl_hash(struct mlx5_flow_act *flow_act, sizeof(dest->vport.num), hash); hash =jhash ((const void *)&dest->vport.vhca_id,sizeof (dest->vport.num), hash); -if (dest->vport.pkt_reformat) - hash =jhash (dest->vport.pkt_reformat, -sizeof (*dest->vport.pkt_reformat), +if (flow_act->pkt_reformat) + hash =jhash (flow_act->pkt_reformat, +sizeof (*flow_act->pkt_reformat), hash);return hash; }
@@ -53,9 +53,11 @@ mlx5_eswitch_termtbl_cmp(struct mlx5_flow_act *flow_act1,if (ret)return ret; -return dest1->vport.pkt_reformat && dest2->vport.pkt_reformat ? -memcmp (dest1->vport.pkt_reformat, dest2->vport.pkt_reformat, -sizeof (*dest1->vport.pkt_reformat)) :0 ; +if (flow_act1->pkt_reformat && flow_act2->pkt_reformat) +return memcmp (flow_act1->pkt_reformat, flow_act2->pkt_reformat, +sizeof (*flow_act1->pkt_reformat)); + +return !(flow_act1->pkt_reformat == flow_act2->pkt_reformat); } static int
Signature · 1 line
2.38.1
PATCH v2 11/11 net/mlx5e: TC, Fix slab-out-of-bounds in parse_tc_actions
In reply to Saeed MahameedFrom: Roi Dayan <[email protected]>
esw_attr is only allocated if namespace is fdb.
BUG: KASAN: slab-out-of-bounds in parse_tc_actions+0xdc6/0x10e0 [mlx5_core] Write of size 4 at addr ffff88815f185b04 by task tc/2135 CPU: 5 PID: 2135 Comm: tc Not tainted 6.1.0-rc2+ #2 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x57/0x7d print_report+0x170/0x471 ? parse_tc_actions+0xdc6/0x10e0 [mlx5_core] kasan_report+0xbc/0xf0 ? parse_tc_actions+0xdc6/0x10e0 [mlx5_core] parse_tc_actions+0xdc6/0x10e0 [mlx5_core]
--- drivers/net/ethernet/mellanox/mlx5/core/en_tc.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c +6 -2
@@ -3633,10 +3633,14 @@ mlx5e_clone_flow_attr_for_post_act(struct mlx5_flow_attr *attr, attr2->action =0 ; attr2->flags =0 ; attr2->parse_attr = parse_attr; - attr2->esw_attr->out_count =0 ; - attr2->esw_attr->split_count =0 ; attr2->dest_chain =0 ; attr2->dest_ft =NULL ; + +if (ns_type ==MLX5_FLOW_NAMESPACE_FDB ) { + attr2->esw_attr->out_count =0 ; + attr2->esw_attr->split_count =0 ; + } +return attr2; }
Signature · 1 line
2.38.1