Collected pending TI dmtimer dts changes
Subsystems (2)
v2 cover Collected pending TI dmtimer dts changes
Hi,
Here are the pending TI dmtimer dts changes posted earlier. The related driver and binding changes are now in the mainline Linux. There has been no changes to these patches, I just updated them against current Linux next and added the tags from Georgi.
Regards,
Tony
Changes since v1:
- Rebase to apply, use base commit fdb02688f22b ("arm64: dts: ti: k3-am65:
Enable McASP nodes at the board level") as requested by Nishanth
Tony Lindgren (4):
arm64: dts: ti: k3-am65: Configure pinctrl for timer IO pads
arm64: dts: ti: k3-am65: Add general purpose timers for am65
arm64: dts: ti: k3-am62: Add general purpose timers for am62
arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 97 ++++++++++++++ arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 45 +++++++ arch/arm64/boot/dts/ti/k3-am625-sk.dts | 17 ++- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 162 +++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi | 63 +++++++++ 5 files changed, 379 insertions(+), 5 deletions(-)
Signature · 1 line
2.38.1
PATCH v2 1/4 arm64: dts: ti: k3-am65: Configure pinctrl for timer IO pads
Compared to the earlier TI SoCs, am65 has an additional level of dedicated multiplexing registers for the timer IO pads.
There are timer IO pads in the MCU domain, and in the MAIN domain. These pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the CASCADE_EN bit is documented in TRM "12.8.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit muxes the previous timer output, or possibly and external TIMER_IO pad source, to the input clock of the selected timer instance for odd numered timers. For the even numbered timers, the CASCADE_EN bit does not do anything. The timer cascade input routing options are shown in TRM "Figure 12-3632. Timers Overview". For handling beyond multiplexing, the driver support for timer cascading should be likely be handled via the clock framework.
--- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 18 ++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi | 18 ++++++++++++++++++ 2 files changed, 36 insertions(+)
arch/arm64/boot/dts/ti/k3-am65-main.dtsi +18 -0
@@ -134,6 +134,24 @@ rng: rng@4e10000 { }; }; + /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */ + main_timerio_input: pinctrl@104200 { + compatible = "pinctrl-single"; + reg = <0x0 0x104200 0x0 0x30>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000001ff>; + }; + + /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */ + main_timerio_output: pinctrl@104280 { + compatible = "pinctrl-single"; + reg = <0x0 0x104280 0x0 0x20>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000f>; + }; + main_pmx0: pinctrl@11c000 { compatible = "pinctrl-single"; reg = <0x0 0x11c000 0x0 0x2e4>;
arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi +18 -0
@@ -20,6 +20,24 @@ phy_gmii_sel: phy@4040 { }; }; + /* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */ + mcu_timerio_input: pinctrl@40f04200 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04200 0x0 0x10>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x00000101>; + }; + + /* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */ + mcu_timerio_output: pinctrl@40f04280 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04280 0x0 0x8>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x00000003>; + }; + mcu_uart0: serial@40a00000 { compatible = "ti,am654-uart"; reg = <0x00 0x40a00000 0x00 0x100>;
Signature · 1 line
2.38.1
PATCH v2 2/4 arm64: dts: ti: k3-am65: Add general purpose timers for am65
In reply to Tony LindgrenThere are 12 general purpose timers on am65 that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional four timers in the MCU domain that do not have interrupts routable for Linux.
We configure the timers with the 25 MHz input clock by default as the 32.768 kHz clock may not be wired on the device. We leave the MCU domain timers clock mux unconfigured, and mark the MCU domain timers reserved. The MCU domain timers are likely reserved by the software for the ESM module.
Compared to am64, the timer clocks are different on am65. And the MCU timers are at a different IO address. Then j72 adds more timers compared to am65 with a total of 30 timers. And the j72 clocks are different.
To avoid duplication for dtsi files, eventually we may want to consider adding timer specific shared dtsi files with the timer clocks mapped using SoC specific files in include/dt-bindings/clock. But let's get am65 timers usable first.
--- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 144 +++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi | 45 +++++++ 2 files changed, 189 insertions(+)
arch/arm64/boot/dts/ti/k3-am65-main.dtsi +144 -0
@@ -285,6 +285,150 @@ main_spi4: spi@2140000 { status = "disabled"; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 23 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 23 0>; + assigned-clock-parents = <&k3_clks 23 1>; + power-domains = <&k3_pds 23 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 24 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 24 0>; + assigned-clock-parents = <&k3_clks 24 1>; + power-domains = <&k3_pds 24 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 27 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 27 0>; + assigned-clock-parents = <&k3_clks 27 1>; + power-domains = <&k3_pds 27 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 28 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 28 0>; + assigned-clock-parents = <&k3_clks 28 1>; + power-domains = <&k3_pds 28 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 29 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 29 0>; + assigned-clock-parents = <&k3_clks 29 1>; + power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 30 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 30 0>; + assigned-clock-parents = <&k3_clks 30 1>; + power-domains = <&k3_pds 30 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 31 0>; + assigned-clocks = <&k3_clks 31 0>; + assigned-clock-parents = <&k3_clks 31 1>; + clock-names = "fck"; + power-domains = <&k3_pds 31 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 32 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 32 0>; + assigned-clock-parents = <&k3_clks 32 1>; + power-domains = <&k3_pds 32 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 33 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 33 0>; + assigned-clock-parents = <&k3_clks 33 1>; + power-domains = <&k3_pds 33 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 34 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 34 0>; + assigned-clock-parents = <&k3_clks 34 1>; + power-domains = <&k3_pds 34 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 25 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 25 0>; + assigned-clock-parents = <&k3_clks 25 1>; + power-domains = <&k3_pds 25 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 26 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 26 0>; + assigned-clock-parents = <&k3_clks 26 1>; + power-domains = <&k3_pds 26 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + sdhci0: mmc@4f80000 { compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>;
arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi +45 -0
51 lines not on this page · raw message
Signature · 1 line
2.38.1
PATCH v2 3/4 arm64: dts: ti: k3-am62: Add general purpose timers for am62
In reply to Tony LindgrenThere are 8 general purpose timers on am65 that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional four timers in the MCU domain that do not have interrupts routable for Linux.
We configure the timers with the 25 MHz input clock by default as the 32.768 kHz clock may not be wired on the device. We leave the MCU domain timers clock mux unconfigured, and mark the MCU domain timers reserved. The MCU domain timers are likely reserved by the software for the ESM module.
Compared to am65, the timers on am62 do not have a dedicated IO mux for the timers. On am62, the timers have different interrupts, clocks and power domains compared to am65, and the MCU timers are at a different IO address.
--- arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 97 ++++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 45 +++++++++++ 2 files changed, 142 insertions(+)
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +97 -0
@@ -192,6 +192,103 @@ main_pmx0: pinctrl@f4000 { pinctrl-single,function-mask = <0xffffffff>; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 36 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 36 2>; + assigned-clock-parents = <&k3_clks 36 3>; + power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 37 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 37 2>; + assigned-clock-parents = <&k3_clks 37 3>; + power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 38 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 38 2>; + assigned-clock-parents = <&k3_clks 38 3>; + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 39 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 39 2>; + assigned-clock-parents = <&k3_clks 39 3>; + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 40 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 40 2>; + assigned-clock-parents = <&k3_clks 40 3>; + power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 41 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 41 2>; + assigned-clock-parents = <&k3_clks 41 3>; + power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 42 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 42 2>; + assigned-clock-parents = <&k3_clks 42 3>; + power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 2>; + assigned-clock-parents = <&k3_clks 43 3>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_uart0: serial@2800000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>;
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi +45 -0
51 lines not on this page · raw message
Signature · 1 line
2.38.1
Nishanth Menon
maintainerRe: [PATCH v2 3/4] arm64: dts: ti: k3-am62: Add general purpose timers for am62
arch/arm64/boot/dts/ti/k3-am62-main.dtsi main_pmx0: pinctrl@f4000 {
Quoted 9 lines · Tony Lindgren
--- arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 97 ++++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 45 +++++++++++ 2 files changed, 142 insertions(+)arch/arm64/boot/dts/ti/k3-am62-main.dtsi +0
-0@@ -192,6 +192,103 @@ main_pmx0: pinctrl@f4000 {
[...]
Quoted 4 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +4
-0+ + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>;
arch/arm64/boot/dts/ti/k3-am62-main.dtsi main_pmx0: pinctrl@f4000 { · line 291
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +10
-0+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 2>; + assigned-clock-parents = <&k3_clks 43 3>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + +
^^ Looks like an extra EoL crept in here.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v2 3/4] arm64: dts: ti: k3-am62: Add general purpose timers for am62
Quoted 11 lines · Nishanth Menon
arch/arm64/boot/dts/ti/k3-am62-main.dtsi main_pmx0: pinctrl@f4000 {
Quoted 9 lines · Tony Lindgren
--- arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 97 ++++++++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 45 +++++++++++ 2 files changed, 142 insertions(+)arch/arm64/boot/dts/ti/k3-am62-main.dtsi +0
-0@@ -192,6 +192,103 @@ main_pmx0: pinctrl@f4000 {[...]
Quoted 15 lines
Quoted 4 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +4
-0+ + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>;arch/arm64/boot/dts/ti/k3-am62-main.dtsi main_pmx0: pinctrl@f4000 { · line 291
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +10
-0+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 2>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 2>; + assigned-clock-parents = <&k3_clks 43 3>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + +^^ Looks like an extra EoL crept in here.
Oops, will send out an updated set with that fixed and without the last patch.
Regards,
Tony
PATCH v2 4/4 arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led
In reply to Tony LindgrenOn am625, pad c17 can be used either in gpio mode or pwm mode to control the connected led. Let's change to use pwm-led for additional brighness control.
The pwm controller is dmtimer7 for pad C17. We configure it for 128 Hz rate (1000000000 / 7812500) similar to what has been done elsewhere for pwm-leds.
--- arch/arm64/boot/dts/ti/k3-am625-sk.dts | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)
arch/arm64/boot/dts/ti/k3-am625-sk.dts +12 -5
@@ -131,18 +131,25 @@ vdd_sd_dv: regulator-4 { }; leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&usr_led_pins_default>; + compatible = "pwm-leds"; led-0 { label = "am62-sk:green:heartbeat"; - gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>; + pwms = <&main_pwm7 0 7812500 0>; + max-brightness = <255>; linux,default-trigger = "heartbeat"; function = LED_FUNCTION_HEARTBEAT; default-state = "off"; }; }; + + main_pwm7: dmtimer-main-pwm-7 { + pinctrl-0 = <&usr_led_pins_default>; + pinctrl-names = "default"; + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&main_timer7>; + }; }; &main_pmx0 {
@@ -203,7 +210,7 @@ AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */ usr_led_pins_default: usr-led-pins-default { pinctrl-single,pins = < - AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */ + AM62X_IOPAD(0x244, PIN_OUTPUT, 2) /* (C17) MMC1_SDWP.TIMER_IO7 */ >; };
Signature · 1 line
2.38.1
Nishanth Menon
maintainerRe: [PATCH v2 4/4] arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led
On 18:35-20221107, Tony Lindgren wrote:
[...]
Quoted 7 lines
--- arch/arm64/boot/dts/ti/k3-am625-sk.dts | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)arch/arm64/boot/dts/ti/k3-am625-sk.dts +0
-0
[...]
arch/arm64/boot/dts/ti/k3-am625-sk.dts vdd_sd_dv: regulator-4 { · line 149
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-am625-sk.dts +5
-0+ + main_pwm7: dmtimer-main-pwm-7 { + pinctrl-0 = <&usr_led_pins_default>; + pinctrl-names = "default"; + compatible = "ti,omap-dmtimer-pwm";
we'd need to convert Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt to yaml for me to be able to accept this :(
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v2 4/4] arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led
Quoted 11 lines · Nishanth Menon
On 18:35-20221107, Tony Lindgren wrote:
[...]Quoted 7 lines
--- arch/arm64/boot/dts/ti/k3-am625-sk.dts | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)arch/arm64/boot/dts/ti/k3-am625-sk.dts +0
-0[...]
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am625-sk.dts vdd_sd_dv: regulator-4 { · line 149
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-am625-sk.dts +5
-0+ + main_pwm7: dmtimer-main-pwm-7 { + pinctrl-0 = <&usr_led_pins_default>; + pinctrl-names = "default"; + compatible = "ti,omap-dmtimer-pwm";we'd need to convert
Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txtto yaml for me to be able to accept this :(
OK. Let's drop this last patch for now.
Regards,
Tony