Skip to contentSkip to conversation

imx8m: USDHC3 base address definition for i.MX8MP

PATCH In review Martyn Welch 4 participants 13 messages Oct 25, 2022 – Nov 8, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v5 1/5 imx8m: USDHC3 base address definition for i.MX8MP

The i.MX8MP also has USDHC3, allow access to the relvant base address definition.

---

Changes in v2:
- None

Changes in v3:
- None

Changes in v4:
- None

Changes in v5:
- None

 arch/arm/include/asm/arch-imx8m/imx-regs.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/include/asm/arch-imx8m/imx-regs.h +1 -1
index 29d5baaab8..c46d4f7e00 100644
@@ -47,7 +47,7 @@
 #define USDHC1_BASE_ADDR	0x30B40000
 #define USDHC2_BASE_ADDR	0x30B50000
 #define QSPI0_AMBA_BASE     0x08000000
-#ifdef CONFIG_IMX8MM
+#if defined(CONFIG_IMX8MM) || defined(CONFIG_IMX8MP)
 #define USDHC3_BASE_ADDR	0x30B60000
 #endif
 #define UART_BASE_ADDR(n)	(			\
Signature · 1 line
2.35.1
#1 lore raw

PATCH v5 2/5 ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP

The i.MX8MP SoC contains 2 more i2c buses. Add support for the configuration of these buses.

---

Changes in v2:
- None

Changes in v3:
- None

Changes in v4:
- None

Changes in v5:
- None

 arch/arm/include/asm/arch-imx8m/imx-regs.h |  4 ++++
 arch/arm/mach-imx/i2c-mxv7.c               |  6 ++++++
 arch/arm/mach-imx/imx8m/clock_imx8mm.c     | 12 +++++++++---
 3 files changed, 19 insertions(+), 3 deletions(-)
arch/arm/include/asm/arch-imx8m/imx-regs.h +4 -0
index c46d4f7e00..6595d97f0a 100644
@@ -44,6 +44,10 @@
 #define I2C3_BASE_ADDR		0x30A40000
 #define I2C4_BASE_ADDR		0x30A50000
 #define UART4_BASE_ADDR		0x30A60000
+#ifdef CONFIG_IMX8MP
+#define I2C5_BASE_ADDR          0x30AD0000
+#define I2C6_BASE_ADDR          0x30AE0000
+#endif
 #define USDHC1_BASE_ADDR	0x30B40000
 #define USDHC2_BASE_ADDR	0x30B50000
 #define QSPI0_AMBA_BASE     0x08000000
arch/arm/mach-imx/i2c-mxv7.c +6 -0
index 85d648b56e..a5866cf9f7 100644
@@ -70,6 +70,12 @@ static void * const i2c_bases[] = {
 #ifdef I2C4_BASE_ADDR
 	(void *)I2C4_BASE_ADDR,
 #endif
+#ifdef I2C5_BASE_ADDR
+	(void *)I2C5_BASE_ADDR,
+#endif
+#ifdef I2C6_BASE_ADDR
+	(void *)I2C6_BASE_ADDR,
+#endif
 };
 
 /* i2c_index can be from 0 - 3 */
arch/arm/mach-imx/imx8m/clock_imx8mm.c +9 -3
index 4db55f8608..64ad57e9b3 100644
@@ -36,11 +36,17 @@ void enable_ocotp_clk(unsigned char enable)
 
 int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
 {
-	/* 0 - 3 is valid i2c num */
-	if (i2c_num > 3)
+	u8 i2c_ccgr[6] = {
+			CCGR_I2C1, CCGR_I2C2, CCGR_I2C3, CCGR_I2C4,
+#if (IS_ENABLED(CONFIG_IMX8MP))
+			CCGR_I2C5_8MP, CCGR_I2C6_8MP
+#endif
+	};
+
+	if (i2c_num > ARRAY_SIZE(i2c_ccgr))
 		return -EINVAL;
 
-	clock_enable(CCGR_I2C1 + i2c_num, !!enable);
+	clock_enable(i2c_ccgr[i2c_num], !!enable);
 
 	return 0;
 }
Signature · 1 line
2.35.1
#2 lore raw

Re: [PATCH v5 2/5] ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP

Quoted 70 lines · Martyn Welch

The i.MX8MP SoC contains 2 more i2c buses. Add support for the configuration of these buses.

---

Changes in v2:
- None

Changes in v3:
- None

Changes in v4:
- None

Changes in v5:
- None

  arch/arm/include/asm/arch-imx8m/imx-regs.h |  4 ++++
  arch/arm/mach-imx/i2c-mxv7.c               |  6 ++++++
  arch/arm/mach-imx/imx8m/clock_imx8mm.c     | 12 +++++++++---
  3 files changed, 19 insertions(+), 3 deletions(-)
arch/arm/include/asm/arch-imx8m/imx-regs.h +4 -0
index c46d4f7e00..6595d97f0a 100644
@@ -44,6 +44,10 @@
  #define I2C3_BASE_ADDR		0x30A40000
  #define I2C4_BASE_ADDR		0x30A50000
  #define UART4_BASE_ADDR		0x30A60000
+#ifdef CONFIG_IMX8MP
+#define I2C5_BASE_ADDR          0x30AD0000
+#define I2C6_BASE_ADDR          0x30AE0000
+#endif
  #define USDHC1_BASE_ADDR	0x30B40000
  #define USDHC2_BASE_ADDR	0x30B50000
  #define QSPI0_AMBA_BASE     0x08000000
arch/arm/mach-imx/i2c-mxv7.c +6 -0
index 85d648b56e..a5866cf9f7 100644
@@ -70,6 +70,12 @@ static void * const i2c_bases[] = {
  #ifdef I2C4_BASE_ADDR
  	(void *)I2C4_BASE_ADDR,
  #endif
+#ifdef I2C5_BASE_ADDR
+	(void *)I2C5_BASE_ADDR,
+#endif
+#ifdef I2C6_BASE_ADDR
+	(void *)I2C6_BASE_ADDR,
+#endif
  };
 
  /* i2c_index can be from 0 - 3 */
arch/arm/mach-imx/imx8m/clock_imx8mm.c +5 -2
index 4db55f8608..64ad57e9b3 100644
@@ -36,11 +36,17 @@ void enable_ocotp_clk(unsigned char enable)
 
  int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
  {
-	/* 0 - 3 is valid i2c num */
-	if (i2c_num > 3)
+	u8 i2c_ccgr[6] = {
+			CCGR_I2C1, CCGR_I2C2, CCGR_I2C3, CCGR_I2C4,
+#if (IS_ENABLED(CONFIG_IMX8MP))
+			CCGR_I2C5_8MP, CCGR_I2C6_8MP
+#endif

arch/arm/mach-imx/imx8m/clock_imx8mm.c void enable_ocotp_clk(unsigned char enable) · line 52

Quoted 10 lines
arch/arm/mach-imx/imx8m/clock_imx8mm.c +4 -1
+	};
+
+	if (i2c_num > ARRAY_SIZE(i2c_ccgr))
  		return -EINVAL;
 
-	clock_enable(CCGR_I2C1 + i2c_num, !!enable);
+	clock_enable(i2c_ccgr[i2c_num], !!enable);
 
  	return 0;
  }

With DM_CLK or SPL_DM_CLK enabled, this function is not needed anymore. Do you have DM_CLK and SPL_DM_CLK enabled?

Regards,
Peng.

#3 lore raw

PATCH v5 2/5 ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP

In reply to Martyn Welch
Quoted 3 lines

The i.MX8MP SoC contains 2 more i2c buses. Add support for the configuration of these buses.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#4 lore raw

PATCH v5 3/5 drivers: power: pmic: Add support for rn5t568 PMIC

In reply to Martyn Welch

Add support for the rn5t568 PMIC to the rn5t567 driver.

---

Changes in v2:
- None

Changes in v3:
- None

Changes in v4:
- None

Changes in v5:
- None

 drivers/power/pmic/rn5t567.c | 1 +
 1 file changed, 1 insertion(+)
drivers/power/pmic/rn5t567.c +1 -0
index d9a8298ebb..9d103dd840 100644
@@ -53,6 +53,7 @@ static struct dm_pmic_ops rn5t567_ops = {
 
 static const struct udevice_id rn5t567_ids[] = {
 	{ .compatible = "ricoh,rn5t567" },
+	{ .compatible = "ricoh,rn5t568" },
 	{ }
 };
 
Signature · 1 line
2.35.1
Reviewed-by on v5 3/5
#5 lore raw

RE: [PATCH v5 3/5] drivers: power: pmic: Add support for rn5t568 PMIC

Quoted 9 lines

-----Original Message-----
From: Martyn Welch [mailto:[email protected]]
Sent: Tuesday, October 25, 2022 6:55 PM
To: [email protected]; [email protected]; Jaehoon Chung <[email protected]>
Cc: Martyn Welch <[email protected]>; [email protected]
Subject: [PATCH v5 3/5] drivers: power: pmic: Add support for rn5t568 PMIC

Quoted 3 lines

Add support for the rn5t568 PMIC to the rn5t567 driver.

Best Regards,
Jaehoon Chung

Quoted 31 lines

---

Changes in v2:
- None

Changes in v3:
- None

Changes in v4:
- None

Changes in v5:
- None

 drivers/power/pmic/rn5t567.c | 1 +
 1 file changed, 1 insertion(+)
drivers/power/pmic/rn5t567.c +1 -1
index d9a8298ebb..9d103dd840 100644
@@ -53,6 +53,7 @@ static struct dm_pmic_ops rn5t567_ops = {
 
 static const struct udevice_id rn5t567_ids[] = {
 	{ .compatible = "ricoh,rn5t567" },
+	{ .compatible = "ricoh,rn5t568" },
 	{ }
 };
 
--

2.35.1

#6 lore raw

PATCH v5 3/5 drivers: power: pmic: Add support for rn5t568 PMIC

In reply to Martyn Welch
Quoted 3 lines

Add support for the rn5t568 PMIC to the rn5t567 driver.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#7 lore raw

PATCH v5 4/5 drivers: power: pmic: Enable use of rn5t567 PMIC in SPL

In reply to Martyn Welch

From: Martyn Welch <[email protected]>

The support added later in this series tweaks the PMIC voltages in the SPL. Enable support for the rn5t567 in SPL builds to allow this to be done cleanly.

---

Changes in v3:
- New patch (replaces addition of legacy support for rn5t567)

Changes in v4:
- None

Changes in v5:
- Rebase to current master branch

 drivers/power/pmic/Kconfig  | 8 ++++++++
 drivers/power/pmic/Makefile | 2 +-
 2 files changed, 9 insertions(+), 1 deletion(-)
drivers/power/pmic/Kconfig +8 -0
index 0478f2aa1d..628d3a94bc 100644
@@ -300,6 +300,14 @@ config PMIC_RN5T567
 	regulators Real-Time Clock and 4 GPIOs. This driver provides
 	register access only.
 
+config SPL_PMIC_RN5T567
+	bool "Enable driver for Ricoh RN5T567 PMIC in SPL"
+	depends on SPL_DM_PMIC
+	---help---
+	The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO
+	regulators Real-Time Clock and 4 GPIOs. This driver provides
+	register access only.
+
 config PMIC_TPS65090
 	bool "Enable driver for Texas Instruments TPS65090 PMIC"
 	---help---
drivers/power/pmic/Makefile +1 -1
index e1d3545490..58c6507c58 100644
@@ -22,7 +22,7 @@ obj-$(CONFIG_$(SPL_)PMIC_AXP) += axp.o
 obj-$(CONFIG_PMIC_MAX8997) += max8997.o
 obj-$(CONFIG_PMIC_QCOM) += pmic_qcom.o
 obj-$(CONFIG_$(SPL_TPL_)PMIC_RK8XX) += rk8xx.o
-obj-$(CONFIG_PMIC_RN5T567) += rn5t567.o
+obj-$(CONFIG_$(SPL_)PMIC_RN5T567) += rn5t567.o
 obj-$(CONFIG_PMIC_TPS65090) += tps65090.o
 obj-$(CONFIG_PMIC_S5M8767) += s5m8767.o
 obj-$(CONFIG_DM_PMIC_TPS65910) += pmic_tps65910_dm.o
Signature · 1 line
2.35.1
Reviewed-by on v5 4/5
#8 lore raw

RE: [PATCH v5 4/5] drivers: power: pmic: Enable use of rn5t567 PMIC in SPL

Quoted 10 lines

-----Original Message-----
From: Martyn Welch [mailto:[email protected]]
Sent: Tuesday, October 25, 2022 6:55 PM
To: [email protected]; [email protected]; Jaehoon Chung <[email protected]>
Cc: Martyn Welch <[email protected]>; Simon Glass <[email protected]>; u- [email protected]
Subject: [PATCH v5 4/5] drivers: power: pmic: Enable use of rn5t567 PMIC in SPL

Quoted 8 lines

From: Martyn Welch <[email protected]>

The support added later in this series tweaks the PMIC voltages in the SPL. Enable support for the rn5t567 in SPL builds to allow this to be done cleanly.

Best Regards,
Jaehoon Chung

Quoted 49 lines

---

Changes in v3:
- New patch (replaces addition of legacy support for rn5t567)

Changes in v4:
- None

Changes in v5:
- Rebase to current master branch

 drivers/power/pmic/Kconfig  | 8 ++++++++
 drivers/power/pmic/Makefile | 2 +-
 2 files changed, 9 insertions(+), 1 deletion(-)
drivers/power/pmic/Kconfig +8 -0
index 0478f2aa1d..628d3a94bc 100644
@@ -300,6 +300,14 @@ config PMIC_RN5T567
 	regulators Real-Time Clock and 4 GPIOs. This driver provides
 	register access only.
 
+config SPL_PMIC_RN5T567
+	bool "Enable driver for Ricoh RN5T567 PMIC in SPL"
+	depends on SPL_DM_PMIC
+	---help---
+	The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO
+	regulators Real-Time Clock and 4 GPIOs. This driver provides
+	register access only.
+
 config PMIC_TPS65090
 	bool "Enable driver for Texas Instruments TPS65090 PMIC"
 	---help---
drivers/power/pmic/Makefile +1 -2
index e1d3545490..58c6507c58 100644
@@ -22,7 +22,7 @@ obj-$(CONFIG_$(SPL_)PMIC_AXP) += axp.o
 obj-$(CONFIG_PMIC_MAX8997) += max8997.o
 obj-$(CONFIG_PMIC_QCOM) += pmic_qcom.o
 obj-$(CONFIG_$(SPL_TPL_)PMIC_RK8XX) += rk8xx.o
-obj-$(CONFIG_PMIC_RN5T567) += rn5t567.o
+obj-$(CONFIG_$(SPL_)PMIC_RN5T567) += rn5t567.o
 obj-$(CONFIG_PMIC_TPS65090) += tps65090.o
 obj-$(CONFIG_PMIC_S5M8767) += s5m8767.o
 obj-$(CONFIG_DM_PMIC_TPS65910) += pmic_tps65910_dm.o
--

2.35.1

#9 lore raw

PATCH v5 4/5 drivers: power: pmic: Enable use of rn5t567 PMIC in SPL

In reply to Martyn Welch
Quoted 7 lines

From: Martyn Welch <[email protected]>
The support added later in this series tweaks the PMIC voltages in the SPL. Enable support for the rn5t567 in SPL builds to allow this to be done cleanly.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#10 lore raw

PATCH v5 5/5 arm: imx8mp: Initial MSC SM2S iMX8MP support

In reply to Martyn Welch

Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.

---

Changes in v2:
- Renamed FDT to closer match kernel
- Sync with kernel FDT
- Update for changes made in U-Boot

Changes in v3:
- Use imx8mp-u-boot.dtsi
- Switch to use of DM PMIC support in SPL

Changes in v4:
- Rebased to latest imx master branch

Changes in v5:
- Rebased on latest master branch
- Add MAINTAINERS entry
- Migrate symbols to Kbuild config
- Simplify header file

 MAINTAINERS                                   |    9 +
 arch/arm/dts/Makefile                         |    1 +
 arch/arm/dts/imx8mp-msc-sm2s-u-boot.dtsi      |   65 +
 arch/arm/dts/imx8mp-msc-sm2s.dts              |  820 ++++++++
 arch/arm/mach-imx/imx8m/Kconfig               |    8 +
 board/msc/sm2s_imx8mp/Kconfig                 |   15 +
 board/msc/sm2s_imx8mp/Makefile                |   12 +
 board/msc/sm2s_imx8mp/imximage-8mp-lpddr4.cfg |    8 +
 board/msc/sm2s_imx8mp/lpddr4_timing.c         | 1842 +++++++++++++++++
 board/msc/sm2s_imx8mp/sm2s_imx8mp.c           |   60 +
 board/msc/sm2s_imx8mp/spl.c                   |  273 +++
 configs/msc_sm2s_imx8mp_defconfig             |  105 +
 include/configs/msc_sm2s_imx8mp.h             |   64 +
 13 files changed, 3282 insertions(+)
 create mode 100644 arch/arm/dts/imx8mp-msc-sm2s-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx8mp-msc-sm2s.dts
 create mode 100644 board/msc/sm2s_imx8mp/Kconfig
 create mode 100644 board/msc/sm2s_imx8mp/Makefile
 create mode 100644 board/msc/sm2s_imx8mp/imximage-8mp-lpddr4.cfg
 create mode 100644 board/msc/sm2s_imx8mp/lpddr4_timing.c
 create mode 100644 board/msc/sm2s_imx8mp/sm2s_imx8mp.c
 create mode 100644 board/msc/sm2s_imx8mp/spl.c
 create mode 100644 configs/msc_sm2s_imx8mp_defconfig
 create mode 100644 include/configs/msc_sm2s_imx8mp.h
MAINTAINERS +9 -0
index cb4d44584d..256e464aff 100644
@@ -398,6 +398,15 @@ F:	drivers/timer/atmel_tcb_timer.c
 F:	include/dt-bindings/mfd/atmel-flexcom.h
 F:	drivers/timer/mchp-pit64b-timer.c
 
+ARM MSC SM2S IMX8MP SOM
+M:	Martyn Welch <[email protected]>
+M:	Ian Ray <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/imx8mp-msc-sm2s*
+F:	board/msc/sm2s_imx8mp/
+F:	configs/msc_sm2s_imx8mp_defconfig
+F:	include/configs/msc_sm2s_imx8mp.h
+
 ARM NEXELL S5P4418
 M:	Stefan Bosch <[email protected]>
 S:	Maintained
arch/arm/dts/Makefile +1 -0
index 30e69b9f67..510b8afc02 100644
@@ -976,6 +976,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
 	imx8mp-dhcom-pdk2.dtb \
 	imx8mp-evk.dtb \
 	imx8mp-icore-mx8mp-edimm2.2.dtb \
+	imx8mp-msc-sm2s.dtb \
 	imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-venice.dtb \
 	imx8mp-venice-gw74xx.dtb \
arch/arm/dts/imx8mp-msc-sm2s-u-boot.dtsi new file +65 -0

65 lines not on this page · raw message

arch/arm/dts/imx8mp-msc-sm2s.dts new file +820 -0

820 lines not on this page · raw message

arch/arm/mach-imx/imx8m/Kconfig +8 -0
index 8cd7c7a8dd..eccee6b213 100644
@@ -284,6 +284,13 @@ config TARGET_IMX8MP_RSB3720A1_6G
 	select SUPPORT_SPL
 	select IMX8M_LPDDR4
 
+config TARGET_MSC_SM2S_IMX8MP
+	bool "MSC SMARC2 i.MX8MPLUS"
+	select BINMAN
+	select IMX8MP
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4
+
 config TARGET_LIBREM5
 	bool "Purism Librem5 Phone"
 	select BINMAN
@@ -311,6 +318,7 @@ source "board/google/imx8mq_phanbell/Kconfig"
 source "board/kontron/pitx_imx8m/Kconfig"
 source "board/kontron/sl-mx8mm/Kconfig"
 source "board/menlo/mx8menlo/Kconfig"
+source "board/msc/sm2s_imx8mp/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mp/Kconfig"
 source "board/purism/librem5/Kconfig"
board/msc/sm2s_imx8mp/Kconfig new file +15 -0
new file mode 100644
index 0000000000..f71a5b2bcd
@@ -0,0 +1,15 @@
+if TARGET_MSC_SM2S_IMX8MP
+
+config SYS_BOARD
+	default "sm2s_imx8mp"
+
+config SYS_VENDOR
+	default "msc"
+
+config SYS_CONFIG_NAME
+	default "msc_sm2s_imx8mp"
+
+config IMX_CONFIG
+	default "board/msc/sm2s_imx8mp/imximage-8mp-lpddr4.cfg"
+
+endif
board/msc/sm2s_imx8mp/Makefile new file +12 -0
new file mode 100644
index 0000000000..f60dd7260c
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2021 AVNET Embedded, MSC Technologies GmbH
+#
+# SPDX-License-Identifier:      GPL-2.0
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o lpddr4_timing.o
+else
+obj-y += sm2s_imx8mp.o
+endif
+
board/msc/sm2s_imx8mp/imximage-8mp-lpddr4.cfg new file +8 -0
new file mode 100644
index 0000000000..8aadedb102
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2021 NXP
+ */
+
+ROM_VERSION	v2
+BOOT_FROM	sd
+LOADER		u-boot-spl-ddr.bin	0x920000
board/msc/sm2s_imx8mp/lpddr4_timing.c new file +1842 -0

1,842 lines not on this page · raw message

board/msc/sm2s_imx8mp/sm2s_imx8mp.c new file +60 -0

60 lines not on this page · raw message

board/msc/sm2s_imx8mp/spl.c new file +273 -0

136 lines not on this page · raw message

configs/msc_sm2s_imx8mp_defconfig new file +105 -0

105 lines not on this page · raw message

include/configs/msc_sm2s_imx8mp.h new file +64 -0

64 lines not on this page · raw message

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.35.1

Part of the diff is not shown here. View the raw message.

#11 lore raw

PATCH v5 5/5 arm: imx8mp: Initial MSC SM2S iMX8MP support

Quoted 3 lines

Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#12 lore raw

PATCH v5 1/5 imx8m: USDHC3 base address definition for i.MX8MP

In reply to Martyn Welch
Quoted 3 lines

The i.MX8MP also has USDHC3, allow access to the relvant base address definition.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================