Skip to contentSkip to conversation

Accessiblity: speakup: specifying the default driver parameters among the module params

PATCH New Osama Muhammad 1 participant 16 messages Nov 9, 2022 Speakup console speech driver

lore
Share & tools
lore
#0 lore raw

cover Accessiblity: speakup: specifying the default driver parameters among the module params

This patch series is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup modules
allows to easily set that at boot, rather than
setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

Osama Muhammad (15):
Accessiblity: speakup_soft: specifying the default driver parameters
among the module params
Accessiblity: speakup_apollo: specifying the default driver parameters
among the module params
Accessiblity: speakup_audptr: specifying the default driver parameters
among the module params
Accessiblity: speakup_bns: specifying the default driver parameters
among the module params
Accessiblity: speakup_decext: specifying the default driver parameters
among the module params
Accessiblity: speakup_decpc: specifying the default driver parameters
among the module params
Accessiblity: speakup_dtlk: specifying the default driver parameters
among the module params
Accessiblity: speakup_dtlk: specifying the default driver parameters
among the module params
Accessiblity: speakup_dummy: specifying the default driver parameters
among the module params
Accessiblity: speakup_keypc: specifying the default driver parameters
among the module params
Accessiblity: speakup_dtlk: specifying the default driver parameters
among the module params
Accessiblity: speakup_spkout: specifying the default driver parameters
among the module params
Accessiblity: speakup_txprt: specifying the default driver parameters
among the module params
Accessiblity: speakup_acntpc: specifying the default driver parameters
among the module params
Accessiblity: speakup_acntsa: specifying the default driver parameters
among the module params

 .../accessibility/speakup/speakup_acntpc.c    | 38 +++++++++---
 .../accessibility/speakup/speakup_acntsa.c    | 37 +++++++++---
 .../accessibility/speakup/speakup_apollo.c    | 46 ++++++++++++---
 .../accessibility/speakup/speakup_audptr.c    | 42 ++++++++++---
 drivers/accessibility/speakup/speakup_bns.c   | 36 ++++++++---
 .../accessibility/speakup/speakup_decext.c    | 44 ++++++++++----
 drivers/accessibility/speakup/speakup_decpc.c | 48 +++++++++++----
 .../accessibility/speakup/speakup_dectlk.c    | 45 ++++++++++----
 drivers/accessibility/speakup/speakup_dtlk.c  | 50 ++++++++++++----
 drivers/accessibility/speakup/speakup_dummy.c | 53 +++++++++++++----
 drivers/accessibility/speakup/speakup_keypc.c | 29 +++++++--
 drivers/accessibility/speakup/speakup_ltlk.c  | 53 +++++++++++++----
 drivers/accessibility/speakup/speakup_soft.c  | 59 ++++++++++++++-----
 .../accessibility/speakup/speakup_spkout.c    | 43 +++++++++++---
 drivers/accessibility/speakup/speakup_txprt.c | 45 +++++++++++---
 15 files changed, 524 insertions(+), 144 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/15 Accessiblity: speakup_soft: specifying the default driver parameters among the module params

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_soft module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_soft.c | 59 ++++++++++++++------
 1 file changed, 43 insertions(+), 16 deletions(-)
drivers/accessibility/speakup/speakup_soft.c +43 -16
index 28c8f60370cf..6d446824677b 100644
@@ -33,21 +33,30 @@ static struct miscdevice synth_device, synthu_device;
 static int init_pos;
 static int misc_registered;
 
-static struct var_t vars[] = {
-	/* DIRECT is put first so that module_param_named can access it easily */
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
-
-	{ CAPS_START, .u.s = {"\x01+3p" } },
-	{ CAPS_STOP, .u.s = {"\x01-3p" } },
-	{ PAUSE, .u.n = {"\x01P" } },
-	{ RATE, .u.n = {"\x01%ds", 2, 0, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x01%dp", 5, 0, 9, 0, 0, NULL } },
-	{ INFLECTION, .u.n = {"\x01%dr", 5, 0, 9, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"\x01%db", 0, 0, 3, 0, 0, NULL } },
-	{ VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
-	{ FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
+
+enum default_vars_id {
+	DIRECT_ID = 0, CAPS_START_ID, CAPS_STOP_ID,
+	PAUSE_ID, RATE_ID, PITCH_ID, INFLECTION_ID,
+	VOL_ID, TONE_ID, PUNCT_ID, VOICE_ID,
+	FREQUENCY_ID, V_LAST_VAR_ID,
+	 NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+
+	[DIRECT_ID]  = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x01+3p" } },
+	[CAPS_STOP_ID]  = { CAPS_STOP, .u.s = {"\x01-3p" } },
+	[PAUSE_ID]  = { PAUSE, .u.n = {"\x01P" } },
+	[RATE_ID]  = { RATE, .u.n = {"\x01%ds", 2, 0, 9, 0, 0, NULL } },
+	[PITCH_ID]  = { PITCH, .u.n = {"\x01%dp", 5, 0, 9, 0, 0, NULL } },
+	[INFLECTION_ID]  = { INFLECTION, .u.n = {"\x01%dr", 5, 0, 9, 0, 0, NULL } },
+	[VOL_ID]  = { VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
+	[TONE_ID]  = { TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
+	[PUNCT_ID]  = { PUNCT, .u.n = {"\x01%db", 0, 0, 3, 0, 0, NULL } },
+	[VOICE_ID]  = { VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
+	[FREQUENCY_ID]  = { FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -451,10 +460,28 @@ static int softsynth_adjust(struct spk_synth *synth, struct st_var_header *var)
 }
 
 module_param_named(start, synth_soft.startup, short, 0444);
-module_param_named(direct, vars[0].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(inflection, vars[INFLECTION_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(frequency, vars[FREQUENCY_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
 MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+MODULE_PARM_DESC(rate, "Sets the rate of the synthesizer.");
+MODULE_PARM_DESC(pitch, "Sets the pitch of the synthesizer.");
+MODULE_PARM_DESC(inflection, "Sets the inflection of the synthesizer.");
+MODULE_PARM_DESC(vol, "Sets the volume of the speech synthesizer.");
+MODULE_PARM_DESC(tone, "Sets the tone of the speech synthesizer.");
+MODULE_PARM_DESC(punct, "Sets the amount of punctuation spoken by the synthesizer.");
+MODULE_PARM_DESC(voice, "Sets the voice used by the synthesizer.");
+MODULE_PARM_DESC(frequency, "Sets the frequency of speech synthesizer.");
 
 module_spk_synth(synth_soft);
 
Signature · 1 line
2.25.1
#2 lore raw

PATCH 2/15 Accessiblity: speakup_apollo: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_apollo module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_apollo.c    | 46 +++++++++++++++----
 1 file changed, 37 insertions(+), 9 deletions(-)
drivers/accessibility/speakup/speakup_apollo.c +37 -9
index c84a7e0864b7..d2fbb3f57221 100644
@@ -24,15 +24,28 @@
 
 static void do_catch_up(struct spk_synth *synth);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"cap, " } },
-	{ CAPS_STOP, .u.s = {"" } },
-	{ RATE, .u.n = {"@W%d", 6, 1, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"@F%x", 10, 0, 15, 0, 0, NULL } },
-	{ VOL, .u.n = {"@A%x", 10, 0, 15, 0, 0, NULL } },
-	{ VOICE, .u.n = {"@V%d", 1, 1, 6, 0, 0, NULL } },
-	{ LANG, .u.n = {"@=%d,", 1, 1, 4, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, VOICE_ID, LANG_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"cap, " } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"" } },
+	[RATE_ID] = { RATE, .u.n = {"@W%d", 6, 1, 9, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"@F%x", 10, 0, 15, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"@A%x", 10, 0, 15, 0, 0, NULL } },
+	[VOICE_ID] = { VOICE, .u.n = {"@V%d", 1, 1, 6, 0, 0, NULL } },
+	[LANG_ID] = { LANG, .u.n = {"@=%d,", 1, 1, 4, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -193,10 +206,25 @@ static void do_catch_up(struct spk_synth *synth)
 module_param_named(ser, synth_apollo.ser, int, 0444);
 module_param_named(dev, synth_apollo.dev_name, charp, 0444);
 module_param_named(start, synth_apollo.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(lang, vars[LANG_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(lang, "Set the lang variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
+
 
 module_spk_synth(synth_apollo);
 
Signature · 1 line
2.25.1
#3 lore raw

PATCH 3/15 Accessiblity: speakup_audptr: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding a default variables to the speakup_audptr module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_audptr.c    | 42 +++++++++++++++----
 1 file changed, 33 insertions(+), 9 deletions(-)
drivers/accessibility/speakup/speakup_audptr.c +33 -9
index 4d16d60db9b2..55813f3e40ff 100644
@@ -19,15 +19,24 @@
 static int synth_probe(struct spk_synth *synth);
 static void synth_flush(struct spk_synth *synth);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x05[f99]" } },
-	{ CAPS_STOP, .u.s = {"\x05[f80]" } },
-	{ RATE, .u.n = {"\x05[r%d]", 10, 0, 20, 100, -10, NULL } },
-	{ PITCH, .u.n = {"\x05[f%d]", 80, 39, 4500, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x05[g%d]", 21, 0, 40, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x05[s%d]", 9, 0, 63, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"\x05[A%c]", 0, 0, 3, 0, 0, "nmsa" } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID, PUNCT_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x05[f99]" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x05[f80]" } },
+	[RATE_ID] = { RATE, .u.n = {"\x05[r%d]", 10, 0, 20, 100, -10, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x05[f%d]", 80, 39, 4500, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x05[g%d]", 21, 0, 40, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x05[s%d]", 9, 0, 63, 0, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"\x05[A%c]", 0, 0, 3, 0, 0, "nmsa" } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -158,10 +167,25 @@ static int synth_probe(struct spk_synth *synth)
 module_param_named(ser, synth_audptr.ser, int, 0444);
 module_param_named(dev, synth_audptr.dev_name, charp, 0444);
 module_param_named(start, synth_audptr.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_audptr);
 
Signature · 1 line
2.25.1
#4 lore raw

PATCH 4/15 Accessiblity: speakup_bns: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_bns module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_bns.c | 36 ++++++++++++++++-----
 1 file changed, 28 insertions(+), 8 deletions(-)
drivers/accessibility/speakup/speakup_bns.c +28 -8
index b8103eb117b8..60507756499c 100644
@@ -16,14 +16,23 @@
 #define SYNTH_CLEAR 0x18
 #define PROCSPEECH '\r'
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x05\x31\x32P" } },
-	{ CAPS_STOP, .u.s = {"\x05\x38P" } },
-	{ RATE, .u.n = {"\x05%dE", 8, 1, 16, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x05%dP", 8, 0, 16, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x05%dV", 8, 0, 16, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x05%dT", 8, 0, 16, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x05\x31\x32P" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x05\x38P" } },
+	[RATE_ID] = { RATE, .u.n = {"\x05%dE", 8, 1, 16, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x05%dP", 8, 0, 16, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x05%dV", 8, 0, 16, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x05%dT", 8, 0, 16, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -113,10 +122,21 @@ static struct spk_synth synth_bns = {
 module_param_named(ser, synth_bns.ser, int, 0444);
 module_param_named(dev, synth_bns.dev_name, charp, 0444);
 module_param_named(start, synth_bns.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
 
 module_spk_synth(synth_bns);
 
Signature · 1 line
2.25.1
#5 lore raw

PATCH 5/15 Accessiblity: speakup_decext: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding a default variables to the speakup_decext module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_decext.c    | 44 ++++++++++++++-----
 1 file changed, 34 insertions(+), 10 deletions(-)
drivers/accessibility/speakup/speakup_decext.c +34 -10
index eaebf62300a4..271bcf279bf9 100644
@@ -38,16 +38,25 @@ static void synth_flush(struct spk_synth *synth);
 
 static int in_escape;
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"[:dv ap 222]" } },
-	{ CAPS_STOP, .u.s = {"[:dv ap 100]" } },
-	{ RATE, .u.n = {"[:ra %d]", 7, 0, 9, 150, 25, NULL } },
-	{ PITCH, .u.n = {"[:dv ap %d]", 100, 0, 100, 0, 0, NULL } },
-	{ INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
-	{ VOL, .u.n = {"[:dv gv %d]", 13, 0, 16, 0, 5, NULL } },
-	{ PUNCT, .u.n = {"[:pu %c]", 0, 0, 2, 0, 0, "nsa" } },
-	{ VOICE, .u.n = {"[:n%c]", 0, 0, 9, 0, 0, "phfdburwkv" } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID, INFLECTION_ID,
+	VOL_ID, PUNCT_ID, VOICE_ID,
+	DIRECT_ID, V_LAST_ID,
+	NB_ID,
+};
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"[:dv ap 222]" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"[:dv ap 100]" } },
+	[RATE_ID] = { RATE, .u.n = {"[:ra %d]", 7, 0, 9, 150, 25, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"[:dv ap %d]", 100, 0, 100, 0, 0, NULL } },
+	[INFLECTION_ID] = { INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"[:dv gv %d]", 13, 0, 16, 0, 5, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"[:pu %c]", 0, 0, 2, 0, 0, "nsa" } },
+	[VOICE_ID] = { VOICE, .u.n = {"[:n%c]", 0, 0, 9, 0, 0, "phfdburwkv" } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -225,10 +234,25 @@ static void synth_flush(struct spk_synth *synth)
 module_param_named(ser, synth_decext.ser, int, 0444);
 module_param_named(dev, synth_decext.dev_name, charp, 0444);
 module_param_named(start, synth_decext.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(inflection, vars[INFLECTION_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(inflection, "Set the inflection variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
 
 module_spk_synth(synth_decext);
 
Signature · 1 line
2.25.1
#6 lore raw

PATCH 6/15 Accessiblity: speakup_decpc: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_decpc module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_decpc.c | 48 +++++++++++++++----
 1 file changed, 38 insertions(+), 10 deletions(-)
drivers/accessibility/speakup/speakup_decpc.c +38 -10
index dec314dee214..083ca9265805 100644
@@ -134,16 +134,27 @@ static int synth_portlist[] = { 0x340, 0x350, 0x240, 0x250, 0 };
 static int in_escape, is_flushing;
 static int dt_stat, dma_state;
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"[:dv ap 200]" } },
-	{ CAPS_STOP, .u.s = {"[:dv ap 100]" } },
-	{ RATE, .u.n = {"[:ra %d]", 9, 0, 18, 150, 25, NULL } },
-	{ PITCH, .u.n = {"[:dv ap %d]", 80, 0, 100, 20, 0, NULL } },
-	{ INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
-	{ VOL, .u.n = {"[:vo se %d]", 5, 0, 9, 5, 10, NULL } },
-	{ PUNCT, .u.n = {"[:pu %c]", 0, 0, 2, 0, 0, "nsa" } },
-	{ VOICE, .u.n = {"[:n%c]", 0, 0, 9, 0, 0, "phfdburwkv" } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID, INFLECTION_ID,
+	VOL_ID, PUNCT_ID, VOICE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID,
+};
+
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"[:dv ap 200]" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"[:dv ap 100]" } },
+	[RATE_ID] = { RATE, .u.n = {"[:ra %d]", 9, 0, 18, 150, 25, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"[:dv ap %d]", 80, 0, 100, 20, 0, NULL } },
+	[INFLECTION_ID] = { INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"[:vo se %d]", 5, 0, 9, 5, 10, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"[:pu %c]", 0, 0, 2, 0, 0, "nsa" } },
+	[VOICE_ID] = { VOICE, .u.n = {"[:n%c]", 0, 0, 9, 0, 0, "phfdburwkv" } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -483,8 +494,25 @@ static void dtpc_release(struct spk_synth *synth)
 }
 
 module_param_named(start, synth_dec_pc.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(inflection, vars[INFLECTION_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
+
 
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(inflection, "Set the inflection variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
 
 module_spk_synth(synth_dec_pc);
 
Signature · 1 line
2.25.1
#7 lore raw

PATCH 7/15 Accessiblity: speakup_dectlk: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding a default variables to the speakup_dectlk module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_dectlk.c    | 45 ++++++++++++++-----
 1 file changed, 35 insertions(+), 10 deletions(-)
drivers/accessibility/speakup/speakup_dectlk.c +35 -10
index 2a7e8d727904..56334405d865 100644
@@ -40,16 +40,24 @@ static int is_flushing;
 static DEFINE_SPINLOCK(flush_lock);
 static DECLARE_WAIT_QUEUE_HEAD(flush);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"[:dv ap 160] " } },
-	{ CAPS_STOP, .u.s = {"[:dv ap 100 ] " } },
-	{ RATE, .u.n = {"[:ra %d] ", 180, 75, 650, 0, 0, NULL } },
-	{ PITCH, .u.n = {"[:dv ap %d] ", 122, 50, 350, 0, 0, NULL } },
-	{ INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
-	{ VOL, .u.n = {"[:dv g5 %d] ", 86, 60, 86, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"[:pu %c] ", 0, 0, 2, 0, 0, "nsa" } },
-	{ VOICE, .u.n = {"[:n%c] ", 0, 0, 9, 0, 0, "phfdburwkv" } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID, INFLECTION_ID,
+	VOL_ID, PUNCT_ID, VOICE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID,
+};
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"[:dv ap 160] " } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"[:dv ap 100 ] " } },
+	[RATE_ID] = { RATE, .u.n = {"[:ra %d] ", 180, 75, 650, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"[:dv ap %d] ", 122, 50, 350, 0, 0, NULL } },
+	[INFLECTION_ID] = { INFLECTION, .u.n = {"[:dv pr %d] ", 100, 0, 10000, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"[:dv g5 %d] ", 86, 60, 86, 0, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"[:pu %c] ", 0, 0, 2, 0, 0, "nsa" } },
+	[VOICE_ID] = { VOICE, .u.n = {"[:n%c] ", 0, 0, 9, 0, 0, "phfdburwkv" } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -306,10 +314,27 @@ static void synth_flush(struct spk_synth *synth)
 module_param_named(ser, synth_dectlk.ser, int, 0444);
 module_param_named(dev, synth_dectlk.dev_name, charp, 0444);
 module_param_named(start, synth_dectlk.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(inflection, vars[INFLECTION_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(inflection, "Set the inflection variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_dectlk);
 
Signature · 1 line
2.25.1
#8 lore raw

PATCH 8/15 Accessiblity: speakup_dtlk: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_dtlk module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_dtlk.c | 50 +++++++++++++++-----
 1 file changed, 39 insertions(+), 11 deletions(-)
drivers/accessibility/speakup/speakup_dtlk.c +39 -11
index 6f01e010aaf4..fa826568937b 100644
@@ -37,17 +37,27 @@ static unsigned int synth_portlist[] = {
 
 static u_char synth_status;
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x01+35p" } },
-	{ CAPS_STOP, .u.s = {"\x01-35p" } },
-	{ RATE, .u.n = {"\x01%ds", 8, 0, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x01%dp", 50, 0, 99, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"\x01%db", 7, 0, 15, 0, 0, NULL } },
-	{ VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
-	{ FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID, PUNCT_ID,
+	VOICE_ID, FREQUENCY_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID,
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x01+35p" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x01-35p" } },
+	[RATE_ID] = { RATE, .u.n = {"\x01%ds", 8, 0, 9, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x01%dp", 50, 0, 99, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"\x01%db", 7, 0, 15, 0, 0, NULL } },
+	[VOICE_ID] = { VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
+	[FREQUENCY_ID] = { FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -376,9 +386,27 @@ static void dtlk_release(struct spk_synth *synth)
 
 module_param_hw_named(port, port_forced, int, ioport, 0444);
 module_param_named(start, synth_dtlk.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(frequency, vars[FREQUENCY_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
 
 MODULE_PARM_DESC(port, "Set the port for the synthesizer (override probing).");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(frequency, "Set the frequency variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_dtlk);
 
Signature · 1 line
2.25.1
#9 lore raw

PATCH 9/15 Accessiblity: speakup_dummy: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_dummy module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_dummy.c | 53 +++++++++++++++----
 1 file changed, 42 insertions(+), 11 deletions(-)
drivers/accessibility/speakup/speakup_dummy.c +42 -11
index 56419dbb28d3..52b2c5d44576 100644
@@ -18,17 +18,30 @@
 #define DRV_VERSION "2.11"
 #define SYNTH_CLEAR '!'
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"CAPS_START\n" } },
-	{ CAPS_STOP, .u.s = {"CAPS_STOP\n" } },
-	{ PAUSE, .u.s = {"PAUSE\n"} },
-	{ RATE, .u.n = {"RATE %d\n", 8, 1, 16, 0, 0, NULL } },
-	{ PITCH, .u.n = {"PITCH %d\n", 8, 0, 16, 0, 0, NULL } },
-	{ INFLECTION, .u.n = {"INFLECTION %d\n", 8, 0, 16, 0, 0, NULL } },
-	{ VOL, .u.n = {"VOL %d\n", 8, 0, 16, 0, 0, NULL } },
-	{ TONE, .u.n = {"TONE %d\n", 8, 0, 16, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"PUNCT %d\n", 0, 0, 3, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	PAUSE_ID,
+	RATE_ID, PITCH_ID, INFLECTION_ID,
+	VOL_ID, TONE_ID, PUNCT_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"CAPS_START\n" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"CAPS_STOP\n" } },
+	[PAUSE_ID] = { PAUSE, .u.s = {"PAUSE\n"} },
+	[RATE_ID] = { RATE, .u.n = {"RATE %d\n", 8, 1, 16, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"PITCH %d\n", 8, 0, 16, 0, 0, NULL } },
+	[INFLECTION_ID] = { INFLECTION, .u.n = {"INFLECTION %d\n", 8, 0, 16, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"VOL %d\n", 8, 0, 16, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"TONE %d\n", 8, 0, 16, 0, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"PUNCT %d\n", 0, 0, 3, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -129,10 +142,28 @@ static struct spk_synth synth_dummy = {
 module_param_named(ser, synth_dummy.ser, int, 0444);
 module_param_named(dev, synth_dummy.dev_name, charp, 0444);
 module_param_named(start, synth_dummy.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(inflection, vars[INFLECTION_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(inflection, "Set the inflection variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_dummy);
 
Signature · 1 line
2.25.1
#10 lore raw

PATCH 10/15 Accessiblity: speakup_keypc: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_keypc module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_keypc.c | 29 +++++++++++++++----
 1 file changed, 23 insertions(+), 6 deletions(-)
drivers/accessibility/speakup/speakup_keypc.c +23 -6
index f61b62f1ea4d..9356f6379560 100644
@@ -33,12 +33,21 @@ static int synth_port;
 static int port_forced;
 static unsigned int synth_portlist[] = { 0x2a8, 0 };
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"[f130]" } },
-	{ CAPS_STOP, .u.s = {"[f90]" } },
-	{ RATE, .u.n = {"\04%c ", 8, 0, 10, 81, -8, NULL } },
-	{ PITCH, .u.n = {"[f%d]", 5, 0, 9, 40, 10, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"[f130]" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"[f90]" } },
+	[RATE_ID] = { RATE, .u.n = {"\04%c ", 8, 0, 10, 81, -8, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"[f%d]", 5, 0, 9, 40, 10, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -305,9 +314,17 @@ static void keynote_release(struct spk_synth *synth)
 
 module_param_hw_named(port, port_forced, int, ioport, 0444);
 module_param_named(start, synth_keypc.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
 
 MODULE_PARM_DESC(port, "Set the port for the synthesizer (override probing).");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
+
 
 module_spk_synth(synth_keypc);
 
Signature · 1 line
2.25.1
#11 lore raw

PATCH 11/15 Accessiblity: speakup_ltlk: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_ltlk module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_ltlk.c | 53 ++++++++++++++++----
 1 file changed, 42 insertions(+), 11 deletions(-)
drivers/accessibility/speakup/speakup_ltlk.c +42 -11
index f885cfaa27c8..1e279ae143bf 100644
@@ -18,17 +18,28 @@
 
 static int synth_probe(struct spk_synth *synth);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x01+35p" } },
-	{ CAPS_STOP, .u.s = {"\x01-35p" } },
-	{ RATE, .u.n = {"\x01%ds", 8, 0, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x01%dp", 50, 0, 99, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
-	{ PUNCT, .u.n = {"\x01%db", 7, 0, 15, 0, 0, NULL } },
-	{ VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
-	{ FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID, PUNCT_ID,
+	VOICE_ID, FREQUENCY_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x01+35p" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x01-35p" } },
+	[RATE_ID] = { RATE, .u.n = {"\x01%ds", 8, 0, 9, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x01%dp", 50, 0, 99, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x01%dv", 5, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x01%dx", 1, 0, 2, 0, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"\x01%db", 7, 0, 15, 0, 0, NULL } },
+	[VOICE_ID] = { VOICE, .u.n = {"\x01%do", 0, 0, 7, 0, 0, NULL } },
+	[FREQUENCY_ID] = { FREQUENCY, .u.n = {"\x01%df", 5, 0, 9, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -160,10 +171,30 @@ static int synth_probe(struct spk_synth *synth)
 module_param_named(ser, synth_ltlk.ser, int, 0444);
 module_param_named(dev, synth_ltlk.dev_name, charp, 0444);
 module_param_named(start, synth_ltlk.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(voice, vars[VOICE_ID].u.n.default_val, int, 0444);
+module_param_named(frequency, vars[FREQUENCY_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(voice, "Set the voice variable on load.");
+MODULE_PARM_DESC(frequency, "Set the frequency variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_ltlk);
 
Signature · 1 line
2.25.1
#12 lore raw

PATCH 12/15 Accessiblity: speakup_spkout: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_spkout module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_spkout.c    | 43 +++++++++++++++----
 1 file changed, 34 insertions(+), 9 deletions(-)
drivers/accessibility/speakup/speakup_spkout.c +34 -9
index 5e3bb3aa98b6..d3f26095b0ee 100644
@@ -18,15 +18,26 @@
 
 static void synth_flush(struct spk_synth *synth);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x05P+" } },
-	{ CAPS_STOP, .u.s = {"\x05P-" } },
-	{ RATE, .u.n = {"\x05R%d", 7, 0, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x05P%d", 3, 0, 9, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x05V%d", 9, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x05T%c", 8, 0, 25, 65, 0, NULL } },
-	{ PUNCT, .u.n = {"\x05M%c", 0, 0, 3, 0, 0, "nsma" } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID, PUNCT_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x05P+" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x05P-" } },
+	[RATE_ID] = { RATE, .u.n = {"\x05R%d", 7, 0, 9, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x05P%d", 3, 0, 9, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x05V%d", 9, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x05T%c", 8, 0, 25, 65, 0, NULL } },
+	[PUNCT_ID] = { PUNCT, .u.n = {"\x05M%c", 0, 0, 3, 0, 0, "nsma" } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -124,10 +135,24 @@ static void synth_flush(struct spk_synth *synth)
 module_param_named(ser, synth_spkout.ser, int, 0444);
 module_param_named(dev, synth_spkout.dev_name, charp, 0444);
 module_param_named(start, synth_spkout.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(punct, vars[PUNCT_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(punct, "Set the punct variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
+
 
 module_spk_synth(synth_spkout);
 
Signature · 1 line
2.25.1
#13 lore raw

PATCH 13/15 Accessiblity: speakup_txprt: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding a default variables to the speakup_txprt module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 drivers/accessibility/speakup/speakup_txprt.c | 45 +++++++++++++++----
 1 file changed, 37 insertions(+), 8 deletions(-)
drivers/accessibility/speakup/speakup_txprt.c +37 -8
index 9e781347f7eb..4d0a0d4c41f0 100644
@@ -16,14 +16,29 @@
 #define SYNTH_CLEAR 0x18
 #define PROCSPEECH '\r' /* process speech char */
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\x05P8" } },
-	{ CAPS_STOP, .u.s = {"\x05P5" } },
-	{ RATE, .u.n = {"\x05R%d", 5, 0, 9, 0, 0, NULL } },
-	{ PITCH, .u.n = {"\x05P%d", 5, 0, 9, 0, 0, NULL } },
-	{ VOL, .u.n = {"\x05V%d", 5, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\x05T%c", 12, 0, 25, 61, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\x05P8" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\x05P5" } },
+	[RATE_ID] = { RATE, .u.n = {"\x05R%d", 5, 0, 9, 0, 0, NULL } },
+	[PITCH_ID] = { PITCH, .u.n = {"\x05P%d", 5, 0, 9, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\x05V%d", 5, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\x05T%c", 12, 0, 25, 61, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 	 };
 
@@ -112,10 +127,24 @@ static struct spk_synth synth_txprt = {
 module_param_named(ser, synth_txprt.ser, int, 0444);
 module_param_named(dev, synth_txprt.dev_name, charp, 0444);
 module_param_named(start, synth_txprt.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
+
 
 module_spk_synth(synth_txprt);
 
Signature · 1 line
2.25.1
#14 lore raw

PATCH 14/15 Accessiblity: speakup_acntpc: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_acntpc module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_acntpc.c    | 38 +++++++++++++++----
 1 file changed, 30 insertions(+), 8 deletions(-)
drivers/accessibility/speakup/speakup_acntpc.c +30 -8
index a55b60754eb1..a27e6bbf05da 100644
@@ -34,14 +34,23 @@ static int synth_port_control;
 static int port_forced;
 static unsigned int synth_portlist[] = { 0x2a8, 0 };
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\033P8" } },
-	{ CAPS_STOP, .u.s = {"\033P5" } },
-	{ RATE, .u.n = {"\033R%c", 9, 0, 17, 0, 0, "0123456789abcdefgh" } },
-	{ PITCH, .u.n = {"\033P%d", 5, 0, 9, 0, 0, NULL } },
-	{ VOL, .u.n = {"\033A%d", 5, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\033V%d", 5, 0, 9, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\033P8" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\033P5" } },
+	[RATE_ID] = { RATE, .u.n = {"\033R%c", 9, 0, 17, 0, 0, "0123456789abcdefgh" } },
+	[PITCH_ID] = { PITCH, .u.n = {"\033P%d", 5, 0, 9, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\033A%d", 5, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\033V%d", 5, 0, 9, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -305,9 +314,22 @@ static void accent_release(struct spk_synth *synth)
 
 module_param_hw_named(port, port_forced, int, ioport, 0444);
 module_param_named(start, synth_acntpc.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
+
+
 
 MODULE_PARM_DESC(port, "Set the port for the synthesizer (override probing).");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_acntpc);
 
Signature · 1 line
2.25.1
#15 lore raw

PATCH 15/15 Accessiblity: speakup_acntsa: specifying the default driver parameters among the module params

In reply to Osama Muhammad

This is an enhancement which allows to specify the default driver parameters among the module parameters.

Adding default variables to the speakup_acntsa module allows to easily set that at boot, rather than setting the sys variables after boot.
More details can be found here:
https://github.com/linux-speakup/speakup/issues/7

---
 .../accessibility/speakup/speakup_acntsa.c    | 37 +++++++++++++++----
 1 file changed, 29 insertions(+), 8 deletions(-)
drivers/accessibility/speakup/speakup_acntsa.c +29 -8
index 2697c51ed6b5..26bb9f9399d3 100644
@@ -19,14 +19,24 @@
 
 static int synth_probe(struct spk_synth *synth);
 
-static struct var_t vars[] = {
-	{ CAPS_START, .u.s = {"\033P8" } },
-	{ CAPS_STOP, .u.s = {"\033P5" } },
-	{ RATE, .u.n = {"\033R%c", 9, 0, 17, 0, 0, "0123456789abcdefgh" } },
-	{ PITCH, .u.n = {"\033P%d", 5, 0, 9, 0, 0, NULL } },
-	{ VOL, .u.n = {"\033A%d", 9, 0, 9, 0, 0, NULL } },
-	{ TONE, .u.n = {"\033V%d", 5, 0, 9, 0, 0, NULL } },
-	{ DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
+
+enum default_vars_id {
+	CAPS_START_ID = 0, CAPS_STOP_ID,
+	RATE_ID, PITCH_ID,
+	VOL_ID, TONE_ID,
+	DIRECT_ID, V_LAST_VAR_ID,
+	NB_ID
+};
+
+
+static struct var_t vars[NB_ID] = {
+	[CAPS_START_ID] = { CAPS_START, .u.s = {"\033P8" } },
+	[CAPS_STOP_ID] = { CAPS_STOP, .u.s = {"\033P5" } },
+	[RATE_ID] = { RATE, .u.n = {"\033R%c", 9, 0, 17, 0, 0, "0123456789abcdefgh" } },
+	[PITCH_ID] = { PITCH, .u.n = {"\033P%d", 5, 0, 9, 0, 0, NULL } },
+	[VOL_ID] = { VOL, .u.n = {"\033A%d", 9, 0, 9, 0, 0, NULL } },
+	[TONE_ID] = { TONE, .u.n = {"\033V%d", 5, 0, 9, 0, 0, NULL } },
+	[DIRECT_ID] = { DIRECT, .u.n = {NULL, 0, 0, 1, 0, 0, NULL } },
 	V_LAST_VAR
 };
 
@@ -129,10 +139,21 @@ static int synth_probe(struct spk_synth *synth)
 module_param_named(ser, synth_acntsa.ser, int, 0444);
 module_param_named(dev, synth_acntsa.dev_name, charp, 0444);
 module_param_named(start, synth_acntsa.startup, short, 0444);
+module_param_named(rate, vars[RATE_ID].u.n.default_val, int, 0444);
+module_param_named(pitch, vars[PITCH_ID].u.n.default_val, int, 0444);
+module_param_named(vol, vars[VOL_ID].u.n.default_val, int, 0444);
+module_param_named(tone, vars[TONE_ID].u.n.default_val, int, 0444);
+module_param_named(direct, vars[DIRECT_ID].u.n.default_val, int, 0444);
 
 MODULE_PARM_DESC(ser, "Set the serial port for the synthesizer (0-based).");
 MODULE_PARM_DESC(dev, "Set the device e.g. ttyUSB0, for the synthesizer.");
 MODULE_PARM_DESC(start, "Start the synthesizer once it is loaded.");
+MODULE_PARM_DESC(rate, "Set the rate variable on load.");
+MODULE_PARM_DESC(pitch, "Set the pitch variable on load.");
+MODULE_PARM_DESC(vol, "Set the vol variable on load.");
+MODULE_PARM_DESC(tone, "Set the tone variable on load.");
+MODULE_PARM_DESC(direct, "Set the direct variable on load.");
+
 
 module_spk_synth(synth_acntsa);
 
Signature · 1 line
2.25.1