qcom: add basic interconnect support to UFS
Subsystems (5)
cover qcom: add basic interconnect support to UFS
This patch set adds very basic support for the interconnect framework to the Qualcomm portion of the UFS framework since the firmware on these platforms expects the interconnect votes to be present. The maximum throughput is requested to match what's already done in a few other drivers.
Here's the relevant entries from the interconnect_summary file in debugfs that shows the two ICC paths are setup for the first UFS host controller on the SA8540p automotive board (sc8280xp).
node tag avg peak
--------------------------------------------------------------------
xm_ufs_mem 0 4294967295 1d84000.ufs 0 0 4294967295 qns_a1noc_snoc 0 4294967295 1d84000.ufs 0 0 4294967295 qnm_gemnoc_cnoc 115 4294967295 1d84000.ufs 0 0 4294967295 a6f8800.usb 0 0 40000 884000.serial 0 115 115 qhs_ufs_mem_cfg 0 4294967295 1d84000.ufs 0 0 4294967295 chm_apps 115 4294967295 1d84000.ufs 0 0 4294967295
a6f8800.usb 0 0 40000
884000.serial 0 115 115qnm_snoc_sf 1000000 4294967295
1d84000.ufs 0 0 4294967295
a6f8800.usb 0 1000000 2500000qns_gem_noc_cnoc 115 4294967295
1d84000.ufs 0 0 4294967295 a6f8800.usb 0 0 40000 884000.serial 0 115 115
qns_llcc 1000000 4294967295
1d84000.ufs 0 0 4294967295
a6f8800.usb 0 1000000 2500000llcc_mc 1000000 4294967295
1d84000.ufs 0 0 4294967295
a6f8800.usb 0 1000000 2500000
ebi 1000000 4294967295
1d84000.ufs 0 0 4294967295
a6f8800.usb 0 1000000 2500000
qnm_aggre1_noc 0 4294967295 1d84000.ufs 0 0 4294967295 qns_gemnoc_sf 1000000 4294967295 1d84000.ufs 0 0 4294967295
a6f8800.usb 0 1000000 2500000
Brian Masney (2):
scsi: ufs: ufs-qcom: add basic interconnect support
arm64: dts: qcom: sc8280xp: add interconnect properties to ufs nodes
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 8 ++++++++ drivers/ufs/host/ufs-qcom.c | 25 +++++++++++++++++++++++++ 2 files changed, 33 insertions(+)
Signature · 1 line
2.38.1
PATCH 1/2 scsi: ufs: ufs-qcom: add basic interconnect support
The firmware on the Qualcomm platforms expects the interconnect votes to be present. Let's add very basic support where the maximum throughput is requested to match what's done in a few other drivers.
This will not break boot on systems where the interconnects and interconnect-names properties are not specified in device tree for UFS since the interconnect framework will silently return.
--- drivers/ufs/host/ufs-qcom.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)
drivers/ufs/host/ufs-qcom.c +25 -0
@@ -7,6 +7,7 @@#include <linux/time.h> #include <linux/clk.h> #include <linux/delay.h> +#include <linux/interconnect.h> #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h>
@@ -936,6 +937,22 @@ static const struct reset_control_ops ufs_qcom_reset_ops = { .deassert = ufs_qcom_reset_deassert, }; +static int ufs_qcom_icc_init (struct device *dev,char *pathname) +{ +struct icc_path *path; +int ret; + + path =devm_of_icc_get (dev, pathname); +if (IS_ERR (path)) +return dev_err_probe (dev,PTR_ERR (path),"failed to acquire interconnect path\n" ); + + ret =icc_set_bw (path,0 ,UINT_MAX ); +if (ret <0 ) +return dev_err_probe (dev, ret,"failed to set bandwidth request\n" ); + +return 0 ; +} +/** * ufs_qcom_init - bind phy with controller * @hba: host controller instance
@@ -991,6 +1008,14 @@ static int ufs_qcom_init(struct ufs_hba *hba) err =dev_err_probe (dev,PTR_ERR (host->generic_phy),"Failed to get PHY\n" ); goto out_variant_clear; } + + err =ufs_qcom_icc_init (dev,"ufs-ddr" ); +if (err) + goto out_variant_clear; + + err =ufs_qcom_icc_init (dev,"cpu-ufs" ); +if (err) + goto out_variant_clear; } host->device_reset = devm_gpiod_get_optional(dev, "reset",
Signature · 1 line
2.38.1
Re: [PATCH 1/2] scsi: ufs: ufs-qcom: add basic interconnect support
Quoted 29 lines · Brian Masney
The firmware on the Qualcomm platforms expects the interconnect votes to be present. Let's add very basic support where the maximum throughput is requested to match what's done in a few other drivers.
This will not break boot on systems where the interconnects and interconnect-names properties are not specified in device tree for UFS since the interconnect framework will silently return.
Signed-off-by Brian Masney <[email protected]>--- drivers/ufs/host/ufs-qcom.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/ufs/host/ufs-qcom.c +1
-0@@ -7,6 +7,7 @@#include <linux/time.h> #include <linux/clk.h> #include <linux/delay.h> +#include <linux/interconnect.h> #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h> @@ -936,6 +937,22 @@ static const struct reset_control_ops ufs_qcom_reset_ops = { .deassert = ufs_qcom_reset_deassert, };
drivers/ufs/host/ufs-qcom.c static const struct reset_control_ops ufs_qcom_reset_ops = { · line 949
Quoted 10 lines
drivers/ufs/host/ufs-qcom.c +10
-0+static int ufs_qcom_icc_init (struct device *dev,char *pathname) +{ +struct icc_path *path; +int ret; + + path =devm_of_icc_get (dev, pathname); +if (IS_ERR (path)) +return dev_err_probe (dev,PTR_ERR (path),"failed to acquire interconnect path\n" ); + + ret =icc_set_bw (path,0 ,UINT_MAX );
Please use icc macros for setting the bandwidth. Like, GBps_to_icc(), MBps_to_icc() etc...
Also, during the init stage you can set a minimum bandwidth that will allow the controller to get probed successfully. Then, you should update the bandwidth based on the gear in pwr_change_notify() callback.
Quoted 11 lines
drivers/ufs/host/ufs-qcom.c +6
-0+if (ret <0 ) +return dev_err_probe (dev, ret,"failed to set bandwidth request\n" ); + +return 0 ; +} +/** * ufs_qcom_init - bind phy with controller * @hba: host controller instance @@ -991,6 +1008,14 @@ static int ufs_qcom_init(struct ufs_hba *hba) err =dev_err_probe (dev,PTR_ERR (host->generic_phy),"Failed to get PHY\n" );
drivers/ufs/host/ufs-qcom.c static int ufs_qcom_init(struct ufs_hba *hba) · line 1018
Quoted 10 lines
drivers/ufs/host/ufs-qcom.c +8
-0goto out_variant_clear; } + + err =ufs_qcom_icc_init (dev,"ufs-ddr" ); +if (err) + goto out_variant_clear; + + err =ufs_qcom_icc_init (dev,"cpu-ufs" ); +if (err) + goto out_variant_clear;
It'd be nice to have a single function that initializes both paths.
Thanks,
Mani
Quoted 6 lines
drivers/ufs/host/ufs-qcom.c +0
-0} host->device_reset = devm_gpiod_get_optional(dev, "reset",Signature · 1 line
2.38.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
Re: [PATCH 1/2] scsi: ufs: ufs-qcom: add basic interconnect support
In reply to Brian MasneyQuoted 29 lines · Brian Masney
The firmware on the Qualcomm platforms expects the interconnect votes to be present. Let's add very basic support where the maximum throughput is requested to match what's done in a few other drivers.
This will not break boot on systems where the interconnects and interconnect-names properties are not specified in device tree for UFS since the interconnect framework will silently return.
Signed-off-by Brian Masney <[email protected]>--- drivers/ufs/host/ufs-qcom.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/ufs/host/ufs-qcom.c +1
-0@@ -7,6 +7,7 @@#include <linux/time.h> #include <linux/clk.h> #include <linux/delay.h> +#include <linux/interconnect.h> #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h> @@ -936,6 +937,22 @@ static const struct reset_control_ops ufs_qcom_reset_ops = { .deassert = ufs_qcom_reset_deassert, };
drivers/ufs/host/ufs-qcom.c static const struct reset_control_ops ufs_qcom_reset_ops = { · line 949
Quoted 10 lines
drivers/ufs/host/ufs-qcom.c +10
-0+static int ufs_qcom_icc_init (struct device *dev,char *pathname) +{ +struct icc_path *path; +int ret; + + path =devm_of_icc_get (dev, pathname); +if (IS_ERR (path)) +return dev_err_probe (dev,PTR_ERR (path),"failed to acquire interconnect path\n" ); + + ret =icc_set_bw (path,0 ,UINT_MAX );
I noticed that this patch bumps peak_bw (and leaves average_bw as 0), while vendor kernels bump average_bw, but ib (peak_bw) is set to 0.
Quoted 24 lines
drivers/ufs/host/ufs-qcom.c +14
-0+if (ret <0 ) +return dev_err_probe (dev, ret,"failed to set bandwidth request\n" ); + +return 0 ; +} +/** * ufs_qcom_init - bind phy with controller * @hba: host controller instance @@ -991,6 +1008,14 @@ static int ufs_qcom_init(struct ufs_hba *hba) err =dev_err_probe (dev,PTR_ERR (host->generic_phy),"Failed to get PHY\n" ); goto out_variant_clear; } + + err =ufs_qcom_icc_init (dev,"ufs-ddr" ); +if (err) + goto out_variant_clear; + + err =ufs_qcom_icc_init (dev,"cpu-ufs" ); +if (err) + goto out_variant_clear; } host->device_reset = devm_gpiod_get_optional(dev, "reset",
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH 1/2] scsi: ufs: ufs-qcom: add basic interconnect support
In reply to Brian MasneyQuoted 10 lines · Brian Masney
The firmware on the Qualcomm platforms expects the interconnect votes to be present. Let's add very basic support where the maximum throughput is requested to match what's done in a few other drivers.
This will not break boot on systems where the interconnects and interconnect-names properties are not specified in device tree for UFS since the interconnect framework will silently return.
Signed-off-by Brian Masney <[email protected]>---
Hi everyone!
This was never merged, but it's actually strictly necessary!
For example UFS dies on SM8450 if we add sync_state to its interconnect driver, as there's no votes cast.
Can we look into this again?
Konrad
Quoted 53 lines
drivers/ufs/host/ufs-qcom.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/ufs/host/ufs-qcom.c +25
-0@@ -7,6 +7,7 @@#include <linux/time.h> #include <linux/clk.h> #include <linux/delay.h> +#include <linux/interconnect.h> #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h> @@ -936,6 +937,22 @@ static const struct reset_control_ops ufs_qcom_reset_ops = { .deassert = ufs_qcom_reset_deassert, }; +static int ufs_qcom_icc_init (struct device *dev,char *pathname) +{ +struct icc_path *path; +int ret; + + path =devm_of_icc_get (dev, pathname); +if (IS_ERR (path)) +return dev_err_probe (dev,PTR_ERR (path),"failed to acquire interconnect path\n" ); + + ret =icc_set_bw (path,0 ,UINT_MAX ); +if (ret <0 ) +return dev_err_probe (dev, ret,"failed to set bandwidth request\n" ); + +return 0 ; +} +/** * ufs_qcom_init - bind phy with controller * @hba: host controller instance @@ -991,6 +1008,14 @@ static int ufs_qcom_init(struct ufs_hba *hba) err =dev_err_probe (dev,PTR_ERR (host->generic_phy),"Failed to get PHY\n" ); goto out_variant_clear; } + + err =ufs_qcom_icc_init (dev,"ufs-ddr" ); +if (err) + goto out_variant_clear; + + err =ufs_qcom_icc_init (dev,"cpu-ufs" ); +if (err) + goto out_variant_clear; } host->device_reset = devm_gpiod_get_optional(dev, "reset",
PATCH 2/2 arm64: dts: qcom: sc8280xp: add interconnect properties to ufs nodes
In reply to Brian MasneyAdd the missing interconnects and interconnect-names properties to the ufs_mem_hc and ufs_card_hc nodes.
--- arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +8 -0
@@ -856,6 +856,10 @@ ufs_mem_hc: ufs@1d84000 { iommus = <&apps_smmu 0xe0 0x0>; + interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>; + interconnect-names = "ufs-ddr", "cpu-ufs"; + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, <&gcc GCC_UFS_PHY_AHB_CLK>,
@@ -924,6 +928,10 @@ ufs_card_hc: ufs@1da4000 { iommus = <&apps_smmu 0x4a0 0x0>; + interconnects = <&aggre2_noc MASTER_UFS_CARD 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_CARD_CFG 0>; + interconnect-names = "ufs-ddr", "cpu-ufs"; + clocks = <&gcc GCC_UFS_CARD_AXI_CLK>, <&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>, <&gcc GCC_UFS_CARD_AHB_CLK>,
Signature · 1 line
2.38.1
Quoted 9 lines · Brian Masney
This patch set adds very basic support for the interconnect framework to the Qualcomm portion of the UFS framework since the firmware on these platforms expects the interconnect votes to be present. The maximum throughput is requested to match what's already done in a few other drivers.
Here's the relevant entries from the
interconnect_summaryfile in debugfs that shows the two ICC paths are setup for the first UFS host controller on the SA8540p automotive board (sc8280xp).
I wonder whether this is solving the same or orthogonal problem as my old patchset here:
https://lore.kernel.org/all/[email protected]/
Best regards,
Krzysztof
Quoted 7 lines · Krzysztof Kozlowski
Quoted 6 lines · Brian Masney
This patch set adds very basic support for the interconnect framework to the Qualcomm portion of the UFS framework since the firmware on these platforms expects the interconnect votes to be present. The maximum throughput is requested to match what's already done in a few other drivers.
Quoted 8 lines
Quoted 3 lines
Here's the relevant entries from the
interconnect_summaryfile in debugfs that shows the two ICC paths are setup for the first UFS host controller on the SA8540p automotive board (sc8280xp).I wonder whether this is solving the same or orthogonal problem as my old patchset here:
More or less it does. Vendor kernel scales both paths according to the gear selected. I was surprised to see just two entries there. sdm845 has 22 entries in its msm-bus scaling table. What was the reason for just two entries in your case?
What was the net result for that patchset? Is it going to be merged anytime?
I think we can start with just a version of this patchset that enables static ICC config and then upgrade that with proper OPP tables, WDYT?
(I wrote 'a version' since I had to modify the patch to set avg_bw instead of setting the peak_bw and to pass different values instead of UINT_MAX, I'll send it).
Signature · 2 lines
With best wishes Dmitry