Skip to contentSkip to conversation

ASoC: ops: Correct bounds check for second channel on SX controls

PATCH In review Charles Keepax 2 participants 6 messages Nov 25, 2022 – Nov 28, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 ASoC: ops: Correct bounds check for second channel on SX controls

Currently the check against the max value for the control is being applied after the value has had the minimum applied and been masked. But the max value simply indicates the number of volume levels on an SX control, and as such should just be applied on the raw value.

Fixes 97eea946b939 ("ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()")

---

Changes since v1:
- Correct fixes SHA.

 sound/soc/soc-ops.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
sound/soc/soc-ops.c +3 -4
index 1970bda074d8a..55b009d3c6815 100644
@@ -464,16 +464,15 @@ int snd_soc_put_volsw_sx(struct snd_kcontrol *kcontrol,
 	ret = err;
 
 	if (snd_soc_volsw_is_stereo(mc)) {
-		unsigned int val2;
-
-		val_mask = mask << rshift;
-		val2 = (ucontrol->value.integer.value[1] + min) & mask;
+		unsigned int val2 = ucontrol->value.integer.value[1];
 
 		if (mc->platform_max && val2 > mc->platform_max)
 			return -EINVAL;
 		if (val2 > max)
 			return -EINVAL;
 
+		val_mask = mask << rshift;
+		val2 = (val2 + min) & mask;
 		val2 = val2 << rshift;
 
 		err = snd_soc_component_update_bits(component, reg2, val_mask,
Signature · 1 line
2.30.2
#1 lore raw

PATCH v2 2/2 ASoC: cs42l51: Correct PGA Volume minimum value

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---

No changes since v1.

 sound/soc/codecs/cs42l51.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/cs42l51.c +1 -1
index 51721edd8f53c..e88d9ff95cdfc 100644
@@ -143,7 +143,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
 			0, 0xA0, 96, adc_att_tlv),
 	SOC_DOUBLE_R_SX_TLV("PGA Volume",
 			CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-			0, 0x19, 30, pga_tlv),
+			0, 0x1A, 30, pga_tlv),
 	SOC_SINGLE("Playback Deemphasis Switch", CS42L51_DAC_CTL, 3, 1, 0),
 	SOC_SINGLE("Auto-Mute Switch", CS42L51_DAC_CTL, 2, 1, 0),
 	SOC_SINGLE("Soft Ramp Switch", CS42L51_DAC_CTL, 1, 1, 0),
Signature · 1 line
2.30.2
#2 lore raw

Re: [PATCH v2 2/2] ASoC: cs42l51: Correct PGA Volume minimum value

Quoted 19 lines · Charles Keepax

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---

No changes since v1.

 sound/soc/codecs/cs42l51.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/cs42l51.c +0 -0
index 51721edd8f53c..e88d9ff95cdfc 100644

sound/soc/codecs/cs42l51.c static const struct snd_kcontrol_new cs42l51_snd_controls[] = { · line 146

Quoted 5 lines
sound/soc/codecs/cs42l51.c +1 -1
@@ -143,7 +143,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
                        0, 0xA0, 96, adc_att_tlv),
        SOC_DOUBLE_R_SX_TLV("PGA Volume",
                        CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-                       0, 0x19, 30, pga_tlv),
+                       0, 0x1A, 30, pga_tlv),

The original patch where this control was added [1] already used 0x1A, however this was later changed to 0x19 in [2]. Your patch now reverts that change. Does this mean [2] was incorrect? If that is the case, shouldn't the commit message for this patch mention that it fixes [2] ?

[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://lore.kernel.org/all/[email protected]/

Best regards,

Guillermo Rodriguez Garcia
[email protected]

#3 lore raw

Re: [PATCH v2 2/2] ASoC: cs42l51: Correct PGA Volume minimum value

Quoted 33 lines · Guillermo Rodriguez Garcia
Quoted 19 lines · Charles Keepax

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---

No changes since v1.

 sound/soc/codecs/cs42l51.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/cs42l51.c +0 -0
index 51721edd8f53c..e88d9ff95cdfc 100644

sound/soc/codecs/cs42l51.c static const struct snd_kcontrol_new cs42l51_snd_controls[] = { · line 146

Quoted 5 lines
sound/soc/codecs/cs42l51.c +1 -1
@@ -143,7 +143,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
                        0, 0xA0, 96, adc_att_tlv),
        SOC_DOUBLE_R_SX_TLV("PGA Volume",
                        CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-                       0, 0x19, 30, pga_tlv),
+                       0, 0x1A, 30, pga_tlv),

The original patch where this control was added [1] already used 0x1A, however this was later changed to 0x19 in [2]. Your patch now reverts that change. Does this mean [2] was incorrect? If that is the case, shouldn't the commit message for this patch mention that it fixes [2] ?

Quoted 3 lines

[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://lore.kernel.org/all/[email protected]/

Hmm... good digging, I didn't realise it was me who broke that. Apologies in that chain I went around and checked a bunch of SX controls to make sure they matched the datasheets, but it seems I got a bit confused by the weird ordering of the values in the datasheet. Since you have hardware would you be able to check, before we merge this revert? A simple check that writing 0 to the control sets the register value to 0x1A and writing 30 sets the register to 0x18 would suffice.

Thanks,
Charles

#4 lore raw

Re: [PATCH v2 2/2] ASoC: cs42l51: Correct PGA Volume minimum value

Quoted 39 lines · Charles Keepax
Quoted 33 lines · Guillermo Rodriguez Garcia
Quoted 19 lines · Charles Keepax

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---

No changes since v1.

 sound/soc/codecs/cs42l51.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/cs42l51.c +0 -0
index 51721edd8f53c..e88d9ff95cdfc 100644

sound/soc/codecs/cs42l51.c static const struct snd_kcontrol_new cs42l51_snd_controls[] = { · line 146

Quoted 5 lines
sound/soc/codecs/cs42l51.c +1 -1
@@ -143,7 +143,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
                        0, 0xA0, 96, adc_att_tlv),
        SOC_DOUBLE_R_SX_TLV("PGA Volume",
                        CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-                       0, 0x19, 30, pga_tlv),
+                       0, 0x1A, 30, pga_tlv),

The original patch where this control was added [1] already used 0x1A, however this was later changed to 0x19 in [2]. Your patch now reverts that change. Does this mean [2] was incorrect? If that is the case, shouldn't the commit message for this patch mention that it fixes [2] ?

Quoted 3 lines

[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://lore.kernel.org/all/[email protected]/

Quoted 8 lines

Hmm... good digging, I didn't realise it was me who broke that. Apologies in that chain I went around and checked a bunch of SX controls to make sure they matched the datasheets, but it seems I got a bit confused by the weird ordering of the values in the datasheet. Since you have hardware would you be able to check, before we merge this revert? A simple check that writing 0 to the control sets the register value to 0x1A and writing 30 sets the register to 0x18 would suffice.

Just checked. The values are correct after applying the patch:

$ amixer cset name='PGA Volume' '0','0'
$ i2cget -y -f  2 0x4A 0x0A
0x1a
$ i2cget -y -f  2 0x4A 0x0B
0x1a
$ amixer cset name='PGA Volume' '30','30'
$ i2cget -y -f  2 0x4A 0x0A
0x18
$ i2cget -y -f  2 0x4A 0x0B
0x18

BR,

Guillermo Rodriguez Garcia
[email protected]

#5 lore raw

Re: [PATCH v2 2/2] ASoC: cs42l51: Correct PGA Volume minimum value

Quoted 41 lines · Guillermo Rodriguez Garcia
Quoted 28 lines · Charles Keepax
Quoted 23 lines · Guillermo Rodriguez Garcia
Quoted 9 lines · Charles Keepax

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---

sound/soc/codecs/cs42l51.c static const struct snd_kcontrol_new cs42l51_snd_controls[] = { · line 146

Quoted 5 lines
sound/soc/codecs/cs42l51.c +1 -1
@@ -143,7 +143,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
                        0, 0xA0, 96, adc_att_tlv),
        SOC_DOUBLE_R_SX_TLV("PGA Volume",
                        CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-                       0, 0x19, 30, pga_tlv),
+                       0, 0x1A, 30, pga_tlv),

The original patch where this control was added [1] already used 0x1A, however this was later changed to 0x19 in [2]. Your patch now reverts that change. Does this mean [2] was incorrect? If that is the case, shouldn't the commit message for this patch mention that it fixes [2] ?

Quoted 3 lines

[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://lore.kernel.org/all/[email protected]/

Quoted 8 lines

Hmm... good digging, I didn't realise it was me who broke that. Apologies in that chain I went around and checked a bunch of SX controls to make sure they matched the datasheets, but it seems I got a bit confused by the weird ordering of the values in the datasheet. Since you have hardware would you be able to check, before we merge this revert? A simple check that writing 0 to the control sets the register value to 0x1A and writing 30 sets the register to 0x18 would suffice.

Just checked. The values are correct after applying the patch:

Quoted 10 lines
$ amixer cset name='PGA Volume' '0','0'
$ i2cget -y -f  2 0x4A 0x0A
0x1a
$ i2cget -y -f  2 0x4A 0x0B
0x1a
$ amixer cset name='PGA Volume' '30','30'
$ i2cget -y -f  2 0x4A 0x0A
0x18
$ i2cget -y -f  2 0x4A 0x0B
0x18

Excellent thank you so much for your help on this. I will send a new version of the patch with the fixes tag applied.

Thanks,
Charles