iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
PATCH 1/1 iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
Some inputs need to be wired up to produce proper measurements, without this change only near zero values are reported.
--- drivers/iio/adc/twl6030-gpadc.c | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
drivers/iio/adc/twl6030-gpadc.c +32 -0
@@ -57,6 +57,18 @@#define TWL6030_GPADCS BIT(1)#define TWL6030_GPADCR BIT(0) +#define USB_VBUS_CTRL_SET 0x04 +#define USB_ID_CTRL_SET 0x06 + +#define TWL6030_MISC1 0xE4 +#define VBUS_MEAS 0x01 +#define ID_MEAS 0x01 + +#define VAC_MEAS 0x04 +#define VBAT_MEAS 0x02 +#define BB_MEAS 0x01 + +/** * struct twl6030_chnl_calib - channel calibration * @gain: slope coefficient for ideal curve
@@ -927,6 +939,26 @@ static int twl6030_gpadc_probe(struct platform_device *pdev)return ret; } + ret =twl_i2c_write_u8 (TWL_MODULE_USB ,VBUS_MEAS ,USB_VBUS_CTRL_SET ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + + ret =twl_i2c_write_u8 (TWL_MODULE_USB ,ID_MEAS ,USB_ID_CTRL_SET ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + + ret =twl_i2c_write_u8 (TWL6030_MODULE_ID0 , +VBAT_MEAS |BB_MEAS |BB_MEAS , +TWL6030_MISC1 ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + indio_dev->name =DRIVER_NAME ; indio_dev->info = &twl6030_gpadc_iio_info; indio_dev->modes =INDIO_DIRECT_MODE ;
Signature · 1 line
2.30.2
Jonathan Cameron
maintainerQuoted 4 lines · On Thu, 1 Dec 2022 19:16:35 +0100 Andreas Kemnade <[email protected]> wrote:
Some inputs need to be wired up to produce proper measurements, without this change only near zero values are reported.
Signed-off-by Andreas Kemnade <[email protected]>
Sounds like a fix to me. If so, Fixes tag?
Anything in here we should be turning off again if the driver is removed or toggling on suspend? If not, other than the space below this looks fine to me.
Jonathan
Quoted 13 lines
--- drivers/iio/adc/twl6030-gpadc.c | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)drivers/iio/adc/twl6030-gpadc.c +1
-0@@ -57,6 +57,18 @@#define TWL6030_GPADCS BIT(1)#define TWL6030_GPADCR BIT(0) +#define USB_VBUS_CTRL_SET 0x04
drivers/iio/adc/twl6030-gpadc.c line 70
Quoted 10 lines
drivers/iio/adc/twl6030-gpadc.c +10
-0+#define USB_ID_CTRL_SET 0x06 + +#define TWL6030_MISC1 0xE4 +#define VBUS_MEAS 0x01 +#define ID_MEAS 0x01 + +#define VAC_MEAS 0x04 +#define VBAT_MEAS 0x02 +#define BB_MEAS 0x01 +
I'm always of the view one blank line is enough! I'll tidy this up whilst applying.
Quoted 31 lines
drivers/iio/adc/twl6030-gpadc.c +21
-0+/** * struct twl6030_chnl_calib - channel calibration * @gain: slope coefficient for ideal curve @@ -927,6 +939,26 @@ static int twl6030_gpadc_probe(struct platform_device *pdev)return ret; } + ret =twl_i2c_write_u8 (TWL_MODULE_USB ,VBUS_MEAS ,USB_VBUS_CTRL_SET ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + + ret =twl_i2c_write_u8 (TWL_MODULE_USB ,ID_MEAS ,USB_ID_CTRL_SET ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + + ret =twl_i2c_write_u8 (TWL6030_MODULE_ID0 , +VBAT_MEAS |BB_MEAS |BB_MEAS , +TWL6030_MISC1 ); +if (ret <0 ) { +dev_err (dev,"failed to wire up inputs\n" ); +return ret; + } + indio_dev->name =DRIVER_NAME ; indio_dev->info = &twl6030_gpadc_iio_info; indio_dev->modes =INDIO_DIRECT_MODE ;
Quoted 9 lines · On Sun, 4 Dec 2022 15:41:52 +0000 Jonathan Cameron <[email protected]> wrote:
Quoted 4 lines · On Thu, 1 Dec 2022 19:16:35 +0100 Andreas Kemnade <[email protected]> wrote:
Some inputs need to be wired up to produce proper measurements, without this change only near zero values are reported.
Signed-off-by Andreas Kemnade <[email protected]>Sounds like a fix to me. If so, Fixes tag?
seems to be there since the beginning, to it would be
I think it was just not used with the charger (which is not in mainline yet), so it was probably ignored.
Quoted 4 lines
Anything in here we should be turning off again if the driver is removed or toggling on suspend? If not, other than the space below this looks fine to me.
I would consider that as configuration, comparing with the nearest relative twl4030, there a similar bit is set in the probe() without disabling it in the remove().
But I think we should set TWL6030_GPADCR in remove() as we do in suspend(), but that is another fix.
Regards,
Andreas
Jonathan Cameron
maintainerQuoted 11 lines · On Sun, 4 Dec 2022 21:27:51 +0100 Andreas Kemnade <[email protected]> wrote:
Quoted 8 lines · On Sun, 4 Dec 2022 15:41:52 +0000 Jonathan Cameron <[email protected]> wrote:
Quoted 4 lines · On Thu, 1 Dec 2022 19:16:35 +0100 Andreas Kemnade <[email protected]> wrote:
Some inputs need to be wired up to produce proper measurements, without this change only near zero values are reported.
Signed-off-by Andreas Kemnade <[email protected]>
Quoted 7 lines
Quoted 1 line
Sounds like a fix to me. If so, Fixes tag?
seems to be there since the beginning, to it would be
Fixes 1696f36482e70 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")I think it was just not used with the charger (which is not in mainline yet), so it was probably ignored.
Makes sense. I've applied it at marked it for stable on basis it wants the fixes tag and would get picked up anyway + appears unlikely to have bad side effects.
Quoted 10 lines
Quoted 5 lines
Anything in here we should be turning off again if the driver is removed or toggling on suspend? If not, other than the space below this looks fine to me.
I would consider that as configuration, comparing with the nearest relative twl4030, there a similar bit is set in the
probe()without disabling it in theremove().But I think we should set
TWL6030_GPADCRinremove()as we do insuspend(), but that is another fix.
There are always more fixes :)
Jonathan
Quoted 3 lines
Regards,
Andreas