Skip to contentSkip to conversation

doc: dtbinding: Add doc for privilege regs settings

PATCH New Jit Loon Lim 1 participant 5 messages Dec 5, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/5 doc: dtbinding: Add doc for privilege regs settings

From: Tien Fong Chee <[email protected]>

Add a document to describe firewall and privilege register settings binding information.

---
 .../misc/socfpga_secreg.txt                   | 26 +++++++++++++++++++
 1 file changed, 26 insertions(+)
 create mode 100644 doc/device-tree-bindings/misc/socfpga_secreg.txt
doc/device-tree-bindings/misc/socfpga_secreg.txt new file +26 -0
new file mode 100644
index 0000000000..66df51f613
@@ -0,0 +1,26 @@
+* Firewall and privilege register settings in device tree
+
+Required properties:
+--------------------
+
+- compatible: should contain "intel,socfpga-secreg"
+- intel,offset-settings: 32-bit offset address of block register, and then
+						 followed by 32-bit value settings.
+
+Example:
+--------
+
+		socfpga_secreg: socfpga-secreg {
+			compatible = "intel,socfpga-secreg";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			u-boot,dm-pre-reloc;
+
+			i_sys_mgr@ffd12000 {
+				reg = <0xffd12000 0x00000228>;
+				intel,offset-settings =
+					<0x00000020 0xff010000>,
+					<0x00000024 0xffffffff>;
+				u-boot,dm-pre-reloc;
+			};
+		};
Signature · 1 line
2.26.2
#1 lore raw

PATCH 2/5 misc: socfpga_secreg: Enable register settings in DTS

From: Tien Fong Chee <[email protected]>

Enable register settings from device tree in SPL, which require high privilege access like firewall registers. This also provides user a clean interface and all register settings are centralized in one place, device tree.

---
 drivers/misc/Kconfig          |  9 ++++
 drivers/misc/Makefile         |  2 +
 drivers/misc/socfpga_secreg.c | 86 +++++++++++++++++++++++++++++++++++
 3 files changed, 97 insertions(+)
 create mode 100644 drivers/misc/socfpga_secreg.c
drivers/misc/Kconfig +9 -0
index a6da6e215d..d9da836675 100644
@@ -645,4 +645,13 @@ config SL28CPLD
 	  the base driver which provides common access methods for the
 	  sub-drivers.
 
+config SPL_SOCFPGA_SEC_REG
+	bool "Enable register setting from device tree in SPL"
+	depends on SPL
+	help
+	  Enable register setting from device tree in SPL, which require
+	  high privilege access like firewall registers. This also
+	  provides user a clean interface and all register settings are
+	  centralized in one place, device tree.
+
 endmenu
drivers/misc/Makefile +2 -0
index d494639cd9..183d92b6e0 100644
@@ -29,6 +29,7 @@ ifdef CONFIG_SPL_BUILD
 obj-$(CONFIG_SANDBOX) += spltest_sandbox.o
 endif
 endif
+
 obj-$(CONFIG_ALI152X) += ali512x.o
 obj-$(CONFIG_ALTERA_SYSID) += altera_sysid.o
 obj-$(CONFIG_ATSHA204A) += atsha204a-i2c.o
@@ -89,3 +90,4 @@ obj-$(CONFIG_K3_AVS0) += k3_avs.o
 obj-$(CONFIG_ESM_K3) += k3_esm.o
 obj-$(CONFIG_ESM_PMIC) += esm_pmic.o
 obj-$(CONFIG_SL28CPLD) += sl28cpld.o
+obj-$(CONFIG_SPL_SOCFPGA_SEC_REG) += socfpga_secreg.o
drivers/misc/socfpga_secreg.c new file +86 -0

86 lines not on this page · raw message

Signature · 1 line
2.26.2
#2 lore raw

PATCH 3/5 arm: dts: socfpga: Copy existing FW & SEC config to DTS

In reply to Jit Loon Lim

From: Tien Fong Chee <[email protected]>

Copy existing firewall and secure register settings in source codes to device tree.

---
 arch/arm/dts/socfpga_agilex-u-boot.dtsi    |  13 ++-
 arch/arm/dts/socfpga_n5x-u-boot.dtsi       |  10 ++
 arch/arm/dts/socfpga_soc64_u-boot.dtsi     | 112 +++++++++++++++++++++
 arch/arm/dts/socfpga_stratix10-u-boot.dtsi |  17 +++-
 4 files changed, 150 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/dts/socfpga_soc64_u-boot.dtsi
arch/arm/dts/socfpga_agilex-u-boot.dtsi +12 -1
index 08f7cf7f7a..774cebd30c 100644
@@ -2,9 +2,10 @@
 /*
  * U-Boot additions
  *
- * Copyright (C) 2019-2020 Intel Corporation <www.intel.com>
+ * Copyright (C) 2019-2021 Intel Corporation <www.intel.com>
  */
 
+#include "socfpga_soc64_u-boot.dtsi"
 #include "socfpga_soc64_fit-u-boot.dtsi"
 
 /{
@@ -84,6 +85,16 @@
 	u-boot,dm-pre-reloc;
 };
 
+&socfpga_secreg {
+	soc_noc_fw_mpfe_csr_inst_0_mpfe_scr@f8020000 {
+		reg = <0xf8020000 0x0000001c>;
+		intel,offset-settings =
+			<0x00000000 0x00010101>,
+			<0x00000004 0x00000001>;
+		u-boot,dm-pre-reloc;
+	};
+};
+
 &sysmgr {
 	compatible = "altr,sys-mgr", "syscon";
 	u-boot,dm-pre-reloc;
arch/arm/dts/socfpga_n5x-u-boot.dtsi +10 -0
index d377ae5f69..98cbd4c808 100644
@@ -5,6 +5,7 @@
  * Copyright (C) 2020-2021 Intel Corporation <www.intel.com>
  */
 
+#include "socfpga_soc64_u-boot.dtsi"
 #include "socfpga_soc64_fit-u-boot.dtsi"
 #include <dt-bindings/clock/n5x-clock.h>
 
@@ -130,6 +131,15 @@
 
 &spi1 {
 	clocks = <&clkmgr N5X_L4_MAIN_CLK>;
+
+&socfpga_secreg {
+	soc_noc_fw_mpfe_csr_inst_0_mpfe_scr@f8020000 {
+		reg = <0xf8020000 0x0000001c>;
+		intel,offset-settings =
+			<0x00000000 0x00010101>,
+			<0x00000004 0x00000001>;
+		u-boot,dm-pre-reloc;
+	};
 };
 
 &sysmgr {
arch/arm/dts/socfpga_soc64_u-boot.dtsi new file +112 -0

112 lines not on this page · raw message

arch/arm/dts/socfpga_stratix10-u-boot.dtsi +16 -1
index 3e3a378046..577cbf9770 100644
@@ -2,7 +2,22 @@
 /*
  * U-Boot additions
  *
- * Copyright (C) 2020 Intel Corporation <www.intel.com>
+ * Copyright (C) 2020-2021 Intel Corporation <www.intel.com>
  */
 
+#include "socfpga_soc64_u-boot.dtsi"
 #include "socfpga_soc64_fit-u-boot.dtsi"
+
+&socfpga_secreg {
+	i_ccu_noc_registers@f7000000 {
+		reg = <0xf7000000 0x00049e60>;
+		intel,offset-settings =
+			<0x000105a0 0x00000000>,
+			<0x000105c0 0x00000000>,
+			<0x000105e0 0x00000000>,
+			<0x00010600 0x00000000>,
+			<0x00010620 0x00000000>,
+			<0x00010640 0x00000000>;
+		u-boot,dm-pre-reloc;
+	};
+};
Signature · 1 line
2.26.2
#3 lore raw

PATCH 4/5 arm: dts: socfpga: Update existing FW & SEC config to DTS

In reply to Jit Loon Lim

From: Tien Fong Chee <[email protected]>

Update N5X existing firewall and secure register settings in source codes to device tree.

---
 arch/arm/dts/socfpga_n5x-u-boot.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/socfpga_n5x-u-boot.dtsi +2 -0
index 98cbd4c808..c25d99366a 100644
@@ -132,6 +132,8 @@
 &spi1 {
 	clocks = <&clkmgr N5X_L4_MAIN_CLK>;
 
+};
+
 &socfpga_secreg {
 	soc_noc_fw_mpfe_csr_inst_0_mpfe_scr@f8020000 {
 		reg = <0xf8020000 0x0000001c>;
Signature · 1 line
2.26.2
#4 lore raw

PATCH 5/5 arm: socfpga: Switch FW settings from codes to DTS

In reply to Jit Loon Lim

From: Tien Fong Chee <[email protected]>

Switching the firewall, and high privilege registers setting in source codes over to device tree implementation.

---
 arch/arm/Kconfig                              |  2 ++
 arch/arm/mach-socfpga/Makefile                | 29 +++++++++++++------
 .../include/mach/system_manager_soc64.h       |  3 ++
 arch/arm/mach-socfpga/spl_agilex.c            |  9 ++++--
 arch/arm/mach-socfpga/spl_n5x.c               |  8 +++--
 arch/arm/mach-socfpga/spl_s10.c               | 11 ++++---
 configs/socfpga_agilex_nand_atf_defconfig     |  1 -
 configs/socfpga_agilex_nand_defconfig         |  1 -
 configs/socfpga_n5x_atf_defconfig             |  1 -
 configs/socfpga_n5x_defconfig                 |  1 -
 configs/socfpga_n5x_vab_defconfig             |  1 -
 configs/socfpga_stratix10_nand_atf_defconfig  |  1 -
 ...onfig => socfpga_stratix10_nand_defconfig} | 18 ++++++------
 13 files changed, 54 insertions(+), 32 deletions(-)
 copy configs/{socfpga_agilex_nand_defconfig => socfpga_stratix10_nand_defconfig} (82%)
 mode change 100755 => 100644
arch/arm/Kconfig +2 -0
index 949ebb46ba..128039e207 100644
@@ -1115,6 +1115,8 @@ config ARCH_SOCFPGA
 	select SPL_LIBGENERIC_SUPPORT
 	select SPL_OF_CONTROL
 	select SPL_SEPARATE_BSS if TARGET_SOCFPGA_SOC64
+	select SPL_DRIVERS_MISC if TARGET_SOCFPGA_SOC64
+	select SPL_SOCFPGA_SEC_REG if TARGET_SOCFPGA_SOC64
 	select SPL_SERIAL
 	select SPL_SYSRESET
 	select SPL_WATCHDOG
arch/arm/mach-socfpga/Makefile +20 -9
index 58a486f6de..0112555926 100644
@@ -35,10 +35,18 @@ obj-y	+= mailbox_s10.o
 obj-y	+= misc_soc64.o
 obj-y	+= mmu-arm64_s10.o
 obj-y	+= reset_manager_s10.o
+obj-y	+= smmu_s10.o
 obj-y	+= system_manager_soc64.o
 obj-y	+= timer_s10.o
 obj-y	+= wrap_handoff_soc64.o
 obj-y	+= wrap_pll_config_soc64.o
+ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_ARMV8_PSCI) += psci.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_ecc_dbe_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_fpga_reconfig_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_registers_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_rsu_s10.o
+endif
 endif
 
 ifdef CONFIG_TARGET_SOCFPGA_AGILEX
@@ -49,11 +57,19 @@ obj-y	+= misc_soc64.o
 obj-y	+= mmu-arm64_s10.o
 obj-y	+= reset_manager_s10.o
 obj-$(CONFIG_SOCFPGA_SECURE_VAB_AUTH)	+= secure_vab.o
+obj-y	+= smmu_s10.o
 obj-y	+= system_manager_soc64.o
 obj-y	+= timer_s10.o
 obj-$(CONFIG_SOCFPGA_SECURE_VAB_AUTH)	+= vab.o
 obj-y	+= wrap_handoff_soc64.o
 obj-y	+= wrap_pll_config_soc64.o
+ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_ARMV8_PSCI) += psci.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_ecc_dbe_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_fpga_reconfig_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_registers_s10.o
+obj-$(CONFIG_ARMV8_PSCI) += smc_rsu_s10.o
+endif
 endif
 
 ifdef CONFIG_TARGET_SOCFPGA_N5X
@@ -71,10 +87,6 @@ obj-$(CONFIG_SOCFPGA_SECURE_VAB_AUTH)	+= vab.o
 obj-y	+= wrap_handoff_soc64.o
 obj-y	+= wrap_pll_config_soc64.o
 ifndef CONFIG_SPL_BUILD
-obj-y   += rsu.o
-obj-y   += rsu_ll_qspi.o
-obj-y   += rsu_misc.o
-obj-y	+= rsu_s10.o
 obj-$(CONFIG_ARMV8_PSCI) += psci.o
 obj-$(CONFIG_ARMV8_PSCI) += smc_ecc_dbe_s10.o
 obj-$(CONFIG_ARMV8_PSCI) += smc_registers_s10.o
@@ -90,21 +102,20 @@ obj-y	+= wrap_iocsr_config.o
 obj-y	+= wrap_pinmux_config.o
 obj-y	+= wrap_sdram_config.o
 endif
-ifdef CONFIG_TARGET_SOCFPGA_SOC64
-obj-y	+= firewall.o
-obj-y	+= spl_soc64.o
-endif
 ifdef CONFIG_TARGET_SOCFPGA_ARRIA10
 obj-y	+= spl_a10.o
 endif
 ifdef CONFIG_TARGET_SOCFPGA_STRATIX10
 obj-y	+= spl_s10.o
+obj-y	+= spl_soc64.o
 endif
 ifdef CONFIG_TARGET_SOCFPGA_AGILEX
 obj-y	+= spl_agilex.o
+obj-y	+= spl_soc64.o
 endif
 ifdef CONFIG_TARGET_SOCFPGA_N5X
 obj-y	+= spl_n5x.o
+obj-y	+= spl_soc64.o
 endif
 else
 obj-$(CONFIG_SPL_ATF) += secure_reg_helper.o
@@ -117,4 +128,4 @@ CFLAGS_wrap_iocsr_config.o	+= -I$(srctree)/board/$(BOARDDIR)
 CFLAGS_wrap_pinmux_config.o	+= -I$(srctree)/board/$(BOARDDIR)
 CFLAGS_wrap_pll_config.o	+= -I$(srctree)/board/$(BOARDDIR)
 CFLAGS_wrap_sdram_config.o	+= -I$(srctree)/board/$(BOARDDIR)
-endif
+endif
\ No newline at end of file
arch/arm/mach-socfpga/include/mach/system_manager_soc64.h +3 -0
index 4441649a31..c24319ffe5 100644
@@ -16,6 +16,9 @@ void populate_sysmgr_pinmux(void);
 #define SYSMGR_SOC64_DMA_PERIPH			0x24
 #define SYSMGR_SOC64_SDMMC			0x28
 #define SYSMGR_SOC64_SDMMC_L3MASTER		0x2c
+#define SYSMGR_SOC64_NANDGRP_L3MASTER		0x34
+#define SYSMGR_SOC64_USB0_L3MASTER		0x38
+#define SYSMGR_SOC64_USB1_L3MASTER		0x3c
 #define SYSMGR_SOC64_EMAC_GLOBAL		0x40
 #define SYSMGR_SOC64_EMAC0			0x44
 #define SYSMGR_SOC64_EMAC1			0x48
arch/arm/mach-socfpga/spl_agilex.c +7 -2
index c279f97cea..a2af30ee57 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2019 Intel Corporation <www.intel.com>
+ * Copyright (C) 2019-2022 Intel Corporation <www.intel.com>
  *
  */
 
@@ -65,7 +65,12 @@ void board_init_f(ulong dummy)
 	print_reset_info();
 	cm_print_clock_quick_summary();
 
-	firewall_setup();
+	ret = uclass_get_device_by_name(UCLASS_NOP, "socfpga-secreg", &dev);
+	if (ret) {
+		printf("Firewall & secure settings init failed: %d\n", ret);
+		hang();
+	}
+
 	ret = uclass_get_device(UCLASS_CACHE, 0, &dev);
 	if (ret) {
 		debug("CCU init failed: %d\n", ret);
arch/arm/mach-socfpga/spl_n5x.c +6 -2
index 92037190e2..2abc722a3c 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2020-2021 Intel Corporation <www.intel.com>
+ * Copyright (C) 2020-2022 Intel Corporation <www.intel.com>
  *
  */
 
@@ -73,7 +73,11 @@ void board_init_f(ulong dummy)
 	print_reset_info();
 	cm_print_clock_quick_summary();
 
-	firewall_setup();
+	ret = uclass_get_device_by_name(UCLASS_NOP, "socfpga-secreg", &dev);
+	if (ret) {
+		printf("Firewall & secure settings init failed: %d\n", ret);
+		hang();
+	}
 
 	ret = uclass_get_device(UCLASS_CACHE, 0, &dev);
 	if (ret) {
arch/arm/mach-socfpga/spl_s10.c +7 -4
index 4044dc335e..da623df097 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2016-2018 Intel Corporation <www.intel.com>
+ * Copyright (C) 2016-2022 Intel Corporation <www.intel.com>
  *
  */
 
@@ -30,6 +30,7 @@ void board_init_f(ulong dummy)
 {
 	const struct cm_config *cm_default_cfg = cm_get_default_config();
 	int ret;
+	struct udevice *dev;
 
 	ret = spl_early_init();
 	if (ret)
@@ -68,7 +69,11 @@ void board_init_f(ulong dummy)
 	print_reset_info();
 	cm_print_clock_quick_summary();
 
-	firewall_setup();
+	ret = uclass_get_device_by_name(UCLASS_NOP, "socfpga-secreg", &dev);
+	if (ret) {
+		printf("Firewall & secure settings init failed: %d\n", ret);
+		hang();
+	}
 
 	/* disable ocram security at CCU for non secure access */
 	clrbits_le32(CCU_REG_ADDR(CCU_CPU0_MPRT_ADMASK_MEM_RAM0),
@@ -77,8 +82,6 @@ void board_init_f(ulong dummy)
 		     CCU_ADMASK_P_MASK | CCU_ADMASK_NS_MASK);
 
 #if CONFIG_IS_ENABLED(ALTERA_SDRAM)
-		struct udevice *dev;
-
 		ret = uclass_get_device(UCLASS_RAM, 0, &dev);
 		if (ret) {
 			debug("DRAM init failed: %d\n", ret);
configs/socfpga_agilex_nand_atf_defconfig +0 -1
index fb92ff2514..58a28481f6 100755
@@ -8,7 +8,6 @@ CONFIG_ENV_SIZE=0x20000
 CONFIG_ENV_OFFSET=0x00200000
 CONFIG_DM_GPIO=y
 CONFIG_SPL_TEXT_BASE=0xffe00000
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_TARGET_SOCFPGA_AGILEX_SOCDK=y
 CONFIG_IDENT_STRING="socfpga_agilex"
 CONFIG_SPL_FS_FAT=y
configs/socfpga_agilex_nand_defconfig +0 -1
index 5613237ae5..f3b3c0b602 100755
@@ -8,7 +8,6 @@ CONFIG_ENV_SIZE=0x20000
 CONFIG_ENV_OFFSET=0x00200000
 CONFIG_DM_GPIO=y
 CONFIG_SPL_TEXT_BASE=0xffe00000
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_TARGET_SOCFPGA_AGILEX_SOCDK=y
 CONFIG_IDENT_STRING="socfpga_agilex"
 CONFIG_SPL_FS_FAT=y
configs/socfpga_n5x_atf_defconfig +0 -1
index d4e77f8147..5e94a923bc 100644
@@ -97,6 +97,5 @@ CONFIG_WDT=y
 CONFIG_PANIC_HANG=y
 CONFIG_SHA512_ALGO=y
 CONFIG_SHA384=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_FS_LOADER=y
 CONFIG_SPL_ENV_SUPPORT=y
configs/socfpga_n5x_defconfig +0 -1
index ede28f530e..1f69277c8c 100644
@@ -85,7 +85,6 @@ CONFIG_WDT=y
 CONFIG_PANIC_HANG=y
 CONFIG_SHA512_ALGO=y
 CONFIG_SHA384=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_FS_LOADER=y
 CONFIG_SPL_ENV_SUPPORT=y
 
configs/socfpga_n5x_vab_defconfig +0 -1
index d2de1eccf5..0f55959a45 100644
@@ -99,6 +99,5 @@ CONFIG_CMD_WDT=y
 CONFIG_PANIC_HANG=y
 CONFIG_SHA512_ALGO=y
 CONFIG_SHA384=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_FS_LOADER=y
 CONFIG_SPL_ENV_SUPPORT=y
configs/socfpga_stratix10_nand_atf_defconfig +0 -1
index a3fd9742e8..29c96bf6f1 100755
@@ -9,7 +9,6 @@ CONFIG_ENV_OFFSET=0x00200000
 CONFIG_SYS_SPI_U_BOOT_OFFS=0x02000000
 CONFIG_DM_GPIO=y
 CONFIG_SPL_TEXT_BASE=0xFFE00000
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
 CONFIG_TARGET_SOCFPGA_STRATIX10_SOCDK=y
 CONFIG_IDENT_STRING="socfpga_stratix10"
 CONFIG_SPL_FS_FAT=y
configs/socfpga_stratix10_nand_defconfig renamed from configs/socfpga_agilex_nand_defconfig +9 -9
old mode 100755
new mode 100644
similarity index 82%
copy from configs/socfpga_agilex_nand_defconfig
copy to configs/socfpga_stratix10_nand_defconfig
index 5613237ae5..f41d2dc82c
@@ -6,28 +6,27 @@ CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_ENV_SIZE=0x20000
 CONFIG_ENV_OFFSET=0x00200000
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x02000000
 CONFIG_DM_GPIO=y
-CONFIG_SPL_TEXT_BASE=0xffe00000
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_TARGET_SOCFPGA_AGILEX_SOCDK=y
-CONFIG_IDENT_STRING="socfpga_agilex"
+CONFIG_SPL_TEXT_BASE=0xFFE00000
+CONFIG_TARGET_SOCFPGA_STRATIX10_SOCDK=y
+CONFIG_IDENT_STRING="socfpga_stratix10"
 CONFIG_SPL_FS_FAT=y
 CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
 # CONFIG_PSCI_RESET is not set
 CONFIG_ARMV8_PSCI=y
-CONFIG_DEFAULT_DEVICE_TREE="socfpga_agilex_socdk_nand"
+CONFIG_DEFAULT_DEVICE_TREE="socfpga_stratix10_socdk_nand"
 CONFIG_NAND_BOOT=y
 CONFIG_BOOTDELAY=5
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="earlycon panic=-1"
 CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="run nandload; run linux_qspi_enable; run nandboot"
+CONFIG_BOOTCOMMAND="run nandload; run linux_qspi_enable; run rsu_status; run nandboot"
 CONFIG_SPL_MTD_SUPPORT=y
 CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_CACHE=y
 CONFIG_SPL_SPI_LOAD=y
 CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="SOCFPGA_AGILEX # "
+CONFIG_SYS_PROMPT="SOCFPGA_STRATIX10 # "
 CONFIG_CMD_MEMTEST=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
@@ -83,4 +82,5 @@ CONFIG_USB_DWC2=y
 CONFIG_USB_STORAGE=y
 CONFIG_DESIGNWARE_WATCHDOG=y
 CONFIG_WDT=y
-# CONFIG_SPL_USE_TINY_PRINTF is not set
\ No newline at end of file
+# CONFIG_SPL_USE_TINY_PRINTF is not set
+CONFIG_PANIC_HANG=y
\ No newline at end of file
Signature · 1 line
2.26.2